Symmons 3602-MB-1.5-TRM Duro Single Handle 1-Spray Tub and Shower Faucet Trim Specification
Add to My manuals2 Pages
advertisement
Location:
Duro
®
3602-TRM, 3602TRMTC
Tub/Shower Trim
Specification Submittal
Feature Highlights
• Duro Tub/Shower Trim
• Requires Temptrol ® Pressure Balancing Tub/Shower Valve
• Metal lever handle
• 7" diverter tub spout
• 1 mode showerhead
• 2.5 gpm (9.5 L/min) flow restrictor
• Components shall be metal and nonmetallic construction, plated in standard Polished Chrome finish
• Available with TA-10 flow control spindle and T-12A cap assembly for Temptrol valve bodies installed with Test Cap
(order p/n 3602TRMTC)
Model Numbers
☐ 3602-TRM
Tub/Shower Trim, Temptrol Pressure Balancing Tub/Shower Valve ordered separately
☐ 3602TRMTC
Tub/Shower Trim with TA-10 flow control spindle and
T-12A cap assembly, must order Temptrol valve with Test Cap
Options/Modifications
☐ -1.5
☐ -2.0
☐ -EX
☐ -L1
☐ -REB
☐ -SH1
☐ -SH2
☐ -SH4
☐ -SS
☐ -T2
☐ -VP
☐ -BBZ
☐ -MB
☐ -STN
CG 1.5 gpm (5.7 L/min) flow restrictor
2.0 gpm (7.6 L/min) flow restrictor
Exposed column/slide bar, hand shower bracket and hand shower wand (36EX)
Less showerhead
Rebuild trim kit, includes TA-10 and TA-4
Alternative 352SH Dia showerhead
Alternative 352SH-3, 3 mode showerhead
Alternative 361SH square showerhead
Slip spout on any tub/shower unit
Alternative 361DTS, square diverter tub spout
Vandal resistant escutcheon screws in place of standard screws
Brushed Bronze finish
Matte Black finish
Satin Nickel finish
Compliance
Note: Append appropriate -suffix to model number.
• ASME A112.18.1/CSA B125.1
Warranty
Limited Lifetime - to the original end purchaser in consumer/residential installations.
5 Years - for industrial/commercial installations.
Refer to www.symmons.com/warranty for complete warranty information.
Go to www.symmons.com/register to register your Symmons product.
Dimensions
EE
M
R
S
P
Q
N
O
T
U
V
K
L
E
F
C
D
G
A
B
H
I
J
Measurements
Ø 2-1/2", 64 mm
6", 152 mm
Ref. 77", 1956 mm
3-1/2", 89 mm
Sq. 7-1/2", 191 mm
Ø 2-1/2", 64 mm
Ref. 32", 813 mm
Ref. 12", 305 mm
3-1/8", 79 mm
3-1/2", 89 mm
Rough-in
2-3/8" ± 1/2", 60 mm ± 13 mm
5-1/2", 140 mm
Male 1/2-14 NPT fitting must protrude 5-1/2" (140 mm) from finished wall
7", 178 mm
6-3/4", 171 mm
6-3/4", 171 mm
5-5/8", 143 mm
2-1/4", 57 mm
2-1/2", 64 mm
5/8", 16 mm
5-5/8", 143 mm
Male 1/2-14 NPT fitting must protrude 4-7/16" (113 mm) from finished wall
FF
II
LL
JJ
-SH1 -SH2
-SH4 -T2
TT
VV
Notes:
1) Valve body and piping not included and shown as reference only.
2) Plaster shield (p/n T-176) for dry wall, plaster or other type walls 1/2" or greater.
3) All dimensions measured from nominal rough-in (see K as reference).
4) Dimensions subject to change without notice.
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Phone: (800) 796-6667 ■ Fax: (800) 961-9621
Copyright © 2019 Symmons Industries, Inc. ■ symmons.com ■ [email protected] ■ ZV-1497 REV D ■ 020119
advertisement
Related manuals
advertisement