Symmons S-3502-CYL-B-MB-1.5-TRM Dia Single Handle 1-Spray Tub and Shower Faucet Trim Specification
Add to My manuals2 Pages
advertisement
Location:
Dia
®
S-3502-CYL-B
Tub/Shower System
Specification Submittal
Feature Highlights Options/Modifications cont.
• Secondary integral diverter
• Metal lever handle
• Adjustable stop screw to limit handle turn
• 7" non-diverter tub spout
• 1 mode showerhead
• 2.5 gpm (9.5 L/min) standard flow restrictor
• Components shall be metal and nonmetallic construction, plated in standard polished chrome finish
Model Numbers
☐ -X Integral service stops - allows water shutoff at valve for service
☐ -X-CHKS Integral check stops - for use in installations where a positive shut-off device is used downstream of mixing valve
☐ -BBZ
☐ -MB
☐ -STN
Brushed Bronze finish
Matte Black finish
Satin Nickel finish
Note: Append appropriate -suffix to model number.
☐ S-3502-CYL-B
Tub/Shower Shower System with Symmons
Temptrol® 4-port pressure balancing mixing valve
☐ S-46-2-BODY
Symmons Temptrol 4-port pressure balancing mixing valve
☐ S-46-2X-BODY
Symmons Temptrol 4-port pressure balancing mixing valve with integral service stops
Compliance
- ASME A112.18.1/CSA B125.1
Warranty
Options/Modifications
☐ -1.5
☐ -2.0
☐ Delete
Suffix B
☐ -IPS
☐ -L/HD
☐ -REB
☐ -REV
☐
☐ -SH3
☐ -SH4
☐ -SS
☐
☐
☐
-SH2
-T4
-TRM
-VP
CG 1.5 gpm (5.7 L/min) flow restrictor
2.0 gpm (7.6 L/min) flow restrictor
Chrome only plastic escutcheon on valve with color graphics/indicators
1/2" female IPS connections
Less showerhead
Rebuild trim kit, includes TA-10 and TA-4
Reverse coring, hot on right, cold on left, for back to back installations
Alternative 352SH-3, 3 mode showerhead
(Chrome and Satin Nickel finish only)
Alternative 362SH Duro showerhead
Alternative 361SH Duro square showerhead
Slip spout (available in chrome and
STN finish only)
Alternative 361TS, non-diverter square tub spout
Trim only, valve must be ordered separately
Vandal resistant escutcheon screws in place of standard screws
Limited Lifetime - to the original end purchaser in consumer/residential installations.
5 Years - for industrial/commercial installations.
Refer to www.symmons.com/warranty for complete warranty information.
Dimensions
EE
S
T
N
O
P
Q
R
K
L
D
E
F
A
B
C
I
J
G
H
M
U
Measurements
Ø 2-1/2", 64 mm
6-3/4", 171 mm
Ref. 77", 1956 mm
3-1/2", 89 mm
Ø 7-1/2", 191 mm
Ø 2-1/2", 64 mm
Ref. 32", 813 mm
Ref. 12", 305 mm
3", 76 mm
2-7/8", 73 mm
Rough-in
2-3/8" ± 1/2", 60 mm ± 13 mm
5-1/4", 133 mm
Male 1/2-14 NPT fitting must protrude 5-1/4" (133 mm) from finished wall
7", 178 mm
6-3/4", 171 mm
6", 152 mm
5-5/8", 143 mm
2-1/4", 57 mm
2-1/2", 64 mm
5-5/8", 143 mm
Male 1/2-14 NPT fitting must protrude 4-7/16" (113 mm) from finished wall
II
LL
JJ
FF
-SH2 -SH3
-SH4 -T4
TT
Notes:
1) Plaster shield (p/n T-176) for dry wall, plaster or other type walls 1/2" or greater.
2) Do not install positive shut-off device/devices that do not allow the valve to flow at least 1.5 gpm to valve outlets.
3) All dimensions measured from nominal rough-in (see K as reference).
4) Dimensions subject to change without notice.
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Phone: (800) 796-6667 ■ Fax: (800) 961-9621
Copyright © 2018 Symmons Industries, Inc. ■ symmons.com ■ [email protected] ■ ZV-1638 REV C ■ 081318
advertisement
Related manuals
advertisement