Owner Instructions

Original Instructions

CAUTION, Read instructions before using the machine.

HVB 160 Henry / HEB 160 Hetty

Numatic Lithium-Ion Battery Powered

www.numatic.com

Kit - AS29E

NOTE*

Located in the bottom of your box is your Lithium-Ion Battery and charger

*

Assembly

1 2 3

4

Operating your machine for the first time

1

Your Battery will arrive in transportation mode.

It is not possible to operate your

Henry, until the battery is first placed on the charger.

2

It is recommended that a battery is fully charged before first use.

Using your machine

2 Speed Switch

CLICK

State of charge

Normal operation

indicator

Operating times

High Speed Setting = >20 mins

Low Speed Settings = >30 mins

@ room temperature

Battery Vacuum State of Charge Indicator

Indicator show battery state of charge (S0C)

Recharging required

Error Condition

Indicator does not illuminate

Indicator flashes on / off

+ +

+

Low

Using your machine

1

Low

2

Wand docking

High

Tool Tidy

6

1

4

7

3

2

Cleaning

5

8

9

2

1

10

1

1

CLICK

2

Fitting the Face on

CLICK

CLICK

2

Removing the Face

6

7

4

5

8

Rating Label

1 Voltage

2

3

Power rating

Weight (ready to use)

Company Name & Address

Machine Description

Machine yr/wk Serial number

WEEE Logo

CE Mark

1

2

6

3

4

5

PPE

(personal protective equipment) That may be required for certain operations.

About your machine

7 8

Ear Protection Safety Footwear Head Protection Safety Gloves Eye Protection Protective

Clothing

NOTE: A risk assessment should be conducted to determine which PPE should be worn.

Dust / Allergens

Protection

Hi Viz Jacket

Caution Floor Sign

Safety Critical Components

Multi-Regional Charger (100-240V ~ 50/60Hz)

Lithium-Ion Battery 2.9Ah @ 4.2V/cell

WEEE Legislation

(Waste, Electrical and Electronic Equipment)

Vacuum cleaner, accessories,Charger and packaging should be sorted for enviromental-friendly recycling.

(Only for EU Countries)

Do not dispose of vacuum cleaner into household waste! According to the European

Directive 2012/19/EU on waste electrical and electronic equipment and its incorporation into national law.

Vacuum cleaners that are no longer suitable for use must be separately collected and sent for recovery in an enviromental-friendly manner.

Daily:-

Keep the machine clean, including hoses and tubes. Ensure the dust bag and filter are fitted.

Regularly examine the charger. Check dust bag frequently. Check the filter is clean.

Weekly - as daily and:-

Check for any worn or damaged parts and replace immediately.

Do not steam clean or pressure wash.

Batteries:-

Always recharge the batteries after use.

Information for DRY USE Vacuum cleaners

Ensure you read the instruction manual before using the appliance.

Operators shall be adequately instructed on the use of these appliances, as with all electrical equipment, care and attention must be exercised at all times during use, you must also make certain that routine and preventative maintenance is carried out periodically to ensure safe operation.

WARNING

Failure to carry out maintenance as necessary, including the replacement of parts to the correct standard could render this equipment unsafe and the manufacturer can accept no responsibility in this respect.

This appliance is for DRY USE only.

You must remove the battery from the machine BEFORE cleaning or maintenance and when replacing parts.

This appliance is intended to be assembled, cleaned and maintained by an adult.

This appliance is not suitable for the collection of biological hazards, hazardous or explosive dusts. Contact your local distributor if you require a appliance capable of performing these tasks.

This machine is not to be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience or knowledge.

Children must not play with the appliance. Cleaning and user maintenance must not be carried out by children without supervision.

You must ensure that the filtration system fitted to the appliance is suitable for the material being collected.

This appliance must not be stored outside, or used in wet environments, or to collect wet materials.

The vacuum cleaner should be stored in a dry place and is for indoor use only.

CAUTION

NOTES

This appliance complies with the requirements of IEC/EN 60335-2-69, IEC 60335-

2-2

This appliance is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and offices.

If the vacuum cleaner stops working, remove the battery from the appliance before investigating where the fault lies.

Failure to rectify the problem or in the event of a breakdown contact your Numatic dealer or the

Numatic Technical helpline +44 (0)1460 269268.

World Wide Lithium-Ion Battery Technical Helpline +1-703-741-5970

If the vacuum cleaner has a blockage, switch off, remove the battery from the appliance, and inspect the floor tool, wands and hose for debris. If the floor tool, wands and hose are clear, replace the dust bag and clean the filter.

This appliance is equipped with a thermal cut-out to protect the motor and other vital appliance parts from overheating.

The vacuum cleaner should be inspected after use for damage.

The size and quality of the dust bag and filters affect the machine efficiency.

Use of non-original dust bags or non-original filters can cause restricted air flow which may lead to appliance overload.

DO

● Keep your appliance clean.

● Fully charge battery before first use.

● Keep the filter clean.

● Use dust bags, they will enhance performance and help keep appliance clean.

● Use a Numatic Original dust bags under fine dust conditions.

● Keep hoses and tubes clear.

● Replace any worn or damaged parts immediately.

● Change dust bag frequently.

● Keep diffuser filter (where fitted) clean.

● Remove battery from appliance when not in use.

DO NOT

● Use to suck up hot ashes, lighted cigarette ends or flammable gases.

● Use steam cleaners, pressure washers or immerse in water to clean the appliance.

● Attempt appliance maintenance or cleaning unless the battery has been removed from the appliance.

● Use or store in a wet environment or to collect wet materials.

● Under any circumstances place foreign objects including (but not limited to) air fresheners, air freshener capsules or scented beads of any type into the top filter of the machine. Doing so can be dangerous and risk damage to the machine and may invalidate the machine warranty.

Important Warnings – Batteries

Read all the warnings before using the battery.

This cleaner uses Numatic Lithium-Ion batteries. Used batteries should be disposed of safely and placed in a sealed plastic bag and then handled according to all locally approved precautions and environmental regulations.

a) b)

Do not dismantle, open or shred secondary cells or batteries.

Do not expose cells or batteries to heat or fire. Avoid storage in direct sunlight j) k) l) m) g) h) i) e) f) c) d) q) r) s) t) n) o) p)

Do not short-circuit a cell or battery. Do not store cells or batteries haphazardly in a box or drawer where they may short-circuit each other or be short circuited by other metal objects.

Do not remove a cell or battery from its original packaging until required for use.

Do not subject cells or batteries to mechanical shock.

In the event of cell leaking, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice.

Do not use any charger other than that specifically provided for use with the appliance.

Observe the plus (+) and minus (-) marks on the cell, battery and appliance and ensure correct use.

Do not use any cell or battery which is not designed for use with the appliance.

Seek medical advice immediately if a cell or battery has been swallowed.

Use only original NUMATIC batteries, when replacement batteries are required.

Keep cells and batteries clean and dry.

Secondary cells and batteries need to be charged before use.

Do not leave a battery on prolonged charge when not in use.

After extended periods of storage, it may be necessary to charge and discharge the cells or batteries several times to obtain maximum performance.

Retain the original appliance literature for future reference.

When possible, remove the battery from the equipment when not in use.

Do not immerse in any liquid.

Do not charge damaged batteries.

If the batteries or cells are leaking, return batteries to a disposal plant or a similar local

facility.

u) The batteries must be removed from the appliance before the appliance is scrapped.

The battery is equipped with electronic thermal protection, refer to the Temperature Range Table below for recommended operating conditions.

Temperature Range Table

Storing +5 ... +35 0 C

Discharge

Charge

Shipment

Humidity

+5 ... +35 0 C

+5 ... +35 0 C

-40 ... +80 0 C

10 ... 90% RH no condensation

In case battery is subject to environmental conditions outside the above parameters user must allow at least 3 hours for battery to acclimatise at room temperature before attempting to operate.

If the battery is found to be faulty at any time, contact Numatic International, or World Wide Lithium-Ion Battery Technical Helpline +1-703-741-5970

Care and Disposal of Li Ion Batteries

DEFECTIVE BATTERIES

ATTENTION

Please follow all safety guidelines set out.

A defective battery should not be stored inside buildings on any account.

• If a customer wishes to return a battery to a supplier, then collection of the battery must be arranged by the supplier, however, Faulty batteries must not be returned through the postal system or by courier.

• If on return to a supplier, OR at a customer base, a suspected defective battery shows any signs of impact damage, distortion, blistering, loose parts or leakage then on no account should it be offered for condition checking. It must be considered defective and the procedures described followed.

• If, on return to a supplier, OR at a customer base, a suspected defective battery, that shows

No signs of impact damage, distortion, blistering, loose parts or leakage, may be offered for condition checking with an appropriate battery condition checking device operated by a competent person.

• If on checking the battery is found to be operational then a single recharge cycle under observation can be attempted with the appropriate Numatic charger.

• If the battery recharges correctly on this single recharge cycle then it can be deemed a good battery.

• If the battery fails to recharge correctly on this single recharge cycle then it must be deemed a defective battery and the procedures followed.

• On no account must any further attempt to recharge be made.

• A defective battery should not be stored inside buildings on any account.

• The defective discharged battery can then be stored in a locked battery waste container which should be plastic or plastic lined and placed away from buildings and clearly signed as a defective battery container with appropriate warnings.

The battery is to be disposed of safely and in accordance with all locally approved precautions and environmental regulations.

1 2

Charging the battery

CLICK

3

5

4

Brand Name: Numatic

Type: Charger 903227

Charger Status Indications

The charger is equiped with a double colour LED’s to indicate the status of the charger and battery.

CHARGE INDICATOR

Green Continuously On

STATUS

Charge Complete

Green Flashing Without Pause

Red Continuously On

Red Flashing Without Pause

Charger in Standby

Charging

Preparing to Charge

ERROR INDICATOR

1 Red Flash With Pause

2 Red Flashes With Pause

3 Red Flashes With Pause

STATUS

Battery Fault

Charger Over Temperature

Charger Fault

NOTE*

Your Battery will arrive in transportaion mode, to preserve shelf life.

It is not possible to operate (discharge) the battery until the battery is placed on the charger.

It is recommended that a battery is fully charged before first use.

Important Warnings – Charger

•

•

•

•

•

•

•

•

•

•

•

•

•

•

Read all these warnings before using the charger.

• CAUTION!

Charge only Numatic Lithium-Ion batteries, other types of batteries may burst causing personal injury and damage.

Check the mains cord regularly for any sign of damage. If the mains cord of the charger is damaged, it must be replaced by an original NUMATIC INTERNATIONAL cord available from the manufacturer or service agent.

Do not use damaged devices.

Protect the charger against moisture and store it in a dry place.

Do not use the charger if it is wet.

The mains voltage available must correspond to the voltage stated on the rating plate of the charger.

Do not operate charger in explosive environment.

Do not carry the charger by holding the mains cord.

Do not handle the electrical cord or plug, with wet hands.

Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

Do not cover the charger.

Do not open the charger. Repairs shall be done only by authorised personnel.

Do not charge damaged batteries.

Do only charge dry batteries.

Do not charge non-rechargeable batteries in this charger.

Warning:

The battery included in this product must only be charged by the Numatic Charger supplied with the product under NO circumstances should an alternative non Numatic charger be used as there is risk severe damage and fire could result. Only use genuine Numatic parts.

Instructions for Use – Charging Batteries

1.

2.

3.

The charger is intended for use only on flat surfaces, place horizontally on floor or work suface.

The charger is intended for use with the power cord supplied, the power unit is capable of operating at different voltages without user adjustment.

If your charger is fitted with a non detachable cable this can only be changed by an authorized service partner.

Make sure cable replacements are a genuine Numatic service part.

If the charger is damaged or does not charge anymore, do not use and contact your supplier.

Charging Procedure:

Ensure the battery is fully inserted into the charger.

Fit the mains power cord to charger and suitable power supply.

Charger Status Lights table, (see page 11).

Hazards

Health Hazards (Acute & Chronic).

The chemicals used in the battery are in a sealed container.

Risk of exposure only occurs if the battery is abused or damaged.

Contact of electrolyte and lithium with skin and eyes should be avoided.

Signs & Symptoms of Exposure.

A damaged or leaking battery can cause chemical burns upon contact.

First Aid Measures

If exposed to any of the Chemicals mentioned in the Hazards section please follow the procedures below:

Eyes.

Flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower eyelid.

Seek medical attention.

Skin.

Remove contaminated clothing and rinse skin with plenty of water or shower for 15 minutes.

Seek medical attention.

Inhalation.

Vacate from site of exposure to fresh air immediately. Use oxygen if available.

Ingestion.

Give at least two glasses of milk or water. Induce vomiting unless patient is unconscious.

Seek medical attention.

Note:

Inhalation, skin contact and eye contact are possible if the battery is damaged.

Exposure to internal contents, the corrosive fumes will be very irritating to skin, eyes and mucous membranes.

Overexposure can cause symptoms of non-fibroid lung injury and membrane irritation.

Spare Parts

902928

903245

901607

909291

907076

907075

Lithium-Ion Battery

Charger UK (Hard Wired)

11” TriTex Filter

NVM - 1CH HepaFlo Dust bags x 3

NVM - 1CH HepaFlo Dust bags x 5

NVM - 1CH HepaFlo Dust bags x 10

Drum Size Operating Times

Data

Protection Class Weight

(Ready to work)

6.88 kg Class III 6 L Hi = >20 mins

Lo = >30 mins

Sound Pressure (LpA)

Uncertainty (KpA)

Hi = 64.5 dB (A)

Lo = 62.6 dB (A)

Size

320 x 340 x 320 mm

Schematic Diagram

DRW-21326 (A06)

Declaration of conformity

Lithium - Ion Battery Warranty.

Numatic International will guarantee your Numatic

Lithium - Ion battery for 500 recharging cycles, providing the cycles have been carried out to the manufacturer’s specifications and requirements.

Failure to use the correct Numatic charger will void your warranty.

HVB 160 / HEB 160

Distributed by:-

Numatic International Limited,

Chard, Somerset, TA20 2GB

Telephone: 01460 68600

UNITED KINGDOM: www.numatic.co.uk GERMANY: www.numatic.de

SWITZERLAND: www.numatic.ch FRANCE: www.numatic.fr

NETHERLANDS: www.numatic.nl PORTUGAL: www.numatic.pt

SOUTH AFRICA: www.numatic.co.za

Subject to change without prior notice. www.numatic.co.uk © Numatic International Limited

905666 11/19 (A08)