Comnet CLKFE1EO(C,U) Kit Series Datasheet

Ethernet-over-Copper Extender With Pass-Through PoE

CLKFE1EO(C,U) Series

-40º TO + 75º EXTENDER PASS-THRU

The ComNet CopperLine® Ethernet over copper kit supports one channel of

10/100Mbps Ethernet with Pass-through PoE over twisted pair cable (CAT-

5, UTP), or over coaxial cable. The single channel units included in the kit may be powered by a PoE switch or the included power supply. These units extend a powered device (PD) over long distance copper. DIP switches are provided for user-selection of local or remote, 10 or 100Mbps, and 1 pair or

4 pair (UTP) settings.

FEATURES

› Transmits individual Ethernet data channels with Passthrough PoE over standard UTP or Coaxial cable

› Extends Ethernet up to 3,000 feet (914 m) at 10 Mbps or

2,000 feet (610 m) at 100 Mbps over UTP cable

› Extends Ethernet up to 5,000 feet (1,524 m) at 10 Mbps or

2,000 feet (610m) at 100 Mbps over Coaxial cable

› Extended temperature operation from -40°C to +75°C

› Extended Pass-through PoE meets the IEEE 802.3af standard for Power over Ethernet

› Full 10/100 Mbps Bandwidth

› Supports Multicast, Unicast and Jumbo Frame

› Symmetric Bandwidth provides consistent upload and download with virtually zero packet loss over the total usable distance

› Type tested to RFC-2544 TCP/IP network bandwidth packet transmission standards

› User-selectable data rate for maximum bandwidth and transmission distance utilization

› Complies with all major IEEE standards and RFC network protocols for UDP, TCP/IP, HTTP/HTTPs

› Designed to meet full compliance with the environmental requirements (ambient operating temperature, mechanical shock, vibration, humidity with condensation, high-line/lowline voltage conditions and transient voltage protection) of

NEMA TS-1/TS-2 and the Caltrans Specification for Traffic

Signal Control Equipment.

› Designed and manufactured in the USA

› LED status indicators confirm operating status

› Small package for limited space installations

› Lifetime warranty

APPLICATIONS

› Retrofit existing analog CCTV installations to Ethernet- based systems

› CCTV systems for casinos, airports, school campuses

LIFETIME WARRANTY WWW.COMNET.NET

TECH SUPPORT: 1.888.678.9427

CLKFE1EO(C,U) Series Ethernet-over-Copper Extender With Pass-Through PoE

SPECIFICATIONS

Ethernet

Data Interface

Data Rate

RFC

Standards

Transmission Distances¹

10/100BaseT(X) Ethernet

DIP-switch selectable 10/100Mbps

Full data rate / full duplex up to the maximum rated distance

2544 TCP/IP Packet Transmission

IEEE 802.3af PoE,

RFC: 768 UDP, 2068 HTTP, 793 TCP

791 IP, 1783 TFTP, 894 IP over Ethernet.

See chart below

Connectors

Ethernet RJ-45

Extended Distance

Operating Power

Coaxial (C): female BNC

Ethernet (U): RJ-45

Powered by PoE or 2-pin screw terminal for local power

Power

Pass-Through Mode

Current Protection

Operates on PoE power or optional 9 to 36 VDC or 24 VAC, 1.5 W

Automatic Resettable Solid-State Current Limiters

Mechanical

LED Indicators

Circuit Board

Size (L×W×H)

Shipping Weight

Environmental

MTBF

Operating Temp

Storage Temp

Relative Humidity

AGENCY COMPLIANCE

Operating Power

Ethernet Link/Activity

Extended Link/Activity

Meets IPC Standard

3.3 × 2.5 × 1.1 in (8.4 × 6.4 × 2.8 cm)

<1 lbs./0.5 kg

>100,000 hours

– 40˚ C to +75˚ C

UL Safety certifications conducted at maximum ambient temperatures (Tma) of 65ºC.

– 40˚ C to +80˚ C

0% to 95% (non-condensing)²

ORDERING INFORMATION

Part Number

CLKFE1EOC

Description

2 Ethernet-over-Coax Extenders, Local/Remote Configurable, Small Size, Includes Power Supplies

Cable

Coax

CLKFE1EOU 2 Ethernet-over-UTP Extenders, Local/Remote Configurable, Small Size, Includes Power Supplies UTP

Accessories:

Options

Unit-appropriate power supply (one each provided with each extender unit, for benign 0 to 50ºC applications only. Hardened power supply available, consult factory)

[2] Add suffix ‘/C’ for Conformally Coated Circuit Boards to extend to condensation conditions (Extra charge, consult factory)

DIN-Rail Mounting Adaptor Kit - With Mounting Hardware (Optional, order model DINBKT1 or DINBKT4) (Suitable for 1CH and 4CH units only)

[1] Distance figures are based on a 50 V PSE PoE power source, and external power supplies for the extenders. Distance figures are obtained using in-house testing mirroring installations. Factors such as coaxial and copper cable quality, the number of connectors and splices in the cable run, the use of PoE, and environmental conditions encountered within the installation might affect the actual transmission distance and should be taken into consideration. Due to advanced negotiation signaling required in IEEE802.3at applications, pass-through applications are limited to IEEE802.3af PD devices only. When using UTP models Pass-Through PoE is only possible in 4-pair mode.

LIFETIME WARRANTY WWW.COMNET.NET

TECH SUPPORT: 1.888.678.9427

CLKFE1EO(C,U) Series Ethernet-over-Copper Extender With Pass-Through PoE

MAXIMUM TRANSMISSION DISTANCES

1

Media

Data Rate 10M

COAX - RG59/U

100M 10M

UTP - 4 pair

100M 10M

UTP - 1 pair

100M

Source Power

Non-PoE Max.Distance

PoE CLASS2 (6.5W)

PoE CLASS3 (13W) 1

1

1

15W 30W

3,000 ft

914 m

750 ft

228 m

5,000 ft

1,524 m

3,000 ft

914 m

850 ft

259 m

15W

2,000 ft

610 m

750 ft

228 m

2,000 ft

610 m

30W

2,000 ft

610 m

850 ft

259 m

15W

914 m

750 ft

228 m

3,000 ft

3,000 ft

914 m

30W

3,000 ft

914 m

850 ft

259 m

15W

2,000 ft

2,000 ft

610 m

750 ft

228 m

610 m

30W

2,000 ft

610 m

850 ft

259 m

3,000 ft

914 m

N/A

N/A

N/A

1,000 ft

305 m

[1] Distance figures are based on a 50 V PSE PoE power source, and external power supplies for the extenders. Distance figures are obtained using in-house testing mirroring installations. Factors such as coaxial and copper cable quality, the number of connectors and splices in the cable run, the use of PoE, and environmental conditions encountered within the installation might affect the actual transmission distance and should be taken into consideration. Due to advanced negotiation signaling required in IEEE802.3at applications, pass-through applications are limited to IEEE802.3af PD devices only. When using UTP models Pass-Through PoE is only possible in 4-pair mode.

TYPICAL APPLICATIONS

PoE Pass-Through Mode

10 or 100 Mbps

PoE Switch

CLFE1EO(C,U)

Extended Distance

CLFE1EO(C,U)

Non-PoE Mode

10 or 100 Mbps

Switch

CLFE1EO(C,U)

12 VDC /

24 VAC

Extended Distance

CLFE1EO(C,U)

12 VDC /

24 VAC

PoE Camera

IP Camera

Cat-5 Cable

UTP or Coax

PoE Power

3 CORPORATE DRIVE | DANBURY, CONNECTICUT 06810 | USA | T: 203.796.5300

| F: 203.796.5303

| TECH SUPPORT: 1.888.678.9427

| [email protected]

8 TURNBERRY PARK ROAD | GILDERSOME | MORLEY | LEEDS, UK LS27 7LE | T: +44 (0)113 307 6400 | F: +44 (0)113 253 7462 | [email protected]

© 2018 Communication Networks. All Rights Reserved. “ComNet” and the “ComNet Logo” are registered trademarks of Communication Networks.

08 Aug 2018