advertisement
Rimage ® Everest Encore™ Printer User Guide
Rimage Corporation
201 General Mills Blvd, Golden
Valley, MN 55427, USA
Toll Free +1.800.445.8288
Rimage Europe GmbH
Albert-Einstein-Straße 26
63128 Dietzenbach, GERMANY
Tel +49 (0)6074.8521.0
Rimage Japan Co., Ltd.
4F Arai #38 Bldg.,
2-7-1 Hamamatsu-cho,
Minato-ku, Tokyo 105-0013 JAPAN
Tel +81.3.6452.8780
Rimage Taiwan
2F.-7, No. 508, Sec. 5,
Zhongxiao East Road., Xinyi Dist.,
Taipei City 110, TAIWAN
Tel +886.2.2726.0100
Rimage Information
Technology (Shanghai)
Co., Ltd.
RM # 206, 207, 2F
No.1 FuXing Zhong Road
HuangPu District
Shanghai, 200025 CHINA
Tel +86.021.5887.8905
Rimage Corporation reserves the right to make improvements to the equipment and software described in this document at any time without any prior notice. Rimage Corporation reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of Rimage Corporation to notify any person or organization of such revisions or changes.
This document may contain links to web sites that were current at the time of publication, but may have moved or become inactive since. This document may contain links to sites on the Internet that are owned and operated by third parties. Rimage Corporation is not responsible for the content of any such third-party site.
© 2020, Rimage Corporation
Rimage® and Everest® are registered trademarks of the Rimage Corporation. Rimage Producer™, Prism™, and Encore™ are trademarks of the Rimage Corporation. Windows® is a registered trademark of Microsoft Corporation.
All other trademarks and registered trademarks are the property of their respective owners.
The most recent version of this document can be found at www.rimage.com/support .
2004001_A For more information visit www.rimage.com/support
Contents
Introduction
..................................................................... 1
About this User Guide ...............................................................1
About the Everest Encore Printer ..............................................1
Unpacking and Setup Instructions
.............................................1
Important Information
..................................................... 2
Technical Support ......................................................................2
Optical Disc Recording Software Disclaimer
..............................2
Safety and Compliance Information
..........................................2
Support Contact Information
.....................................................2
Safety Precautions ....................................................................................3
Compliance Information ...........................................................................5
Everest Encore Printer Requirements ................................ 6
Ribbon Requirements
................................................................6
Everest Encore Ribbons .............................................................................6
Label Design Requirements
.......................................................6
Print Requirements
....................................................................7
Identifying the Parts of the Everest Encore Printer
............ 8
Front View
................................................................................8
Control Panel .............................................................................8
Control Panel Indicators ............................................................................8
Switches
.....................................................................................8
AC Voltage Switch .....................................................................................8
Control Panel Indicators ............................................................................8
Back View
..................................................................................9
AC Voltage Switch ...................................................................................10
Mode Switch ...........................................................................................10
Operating the Everest Encore Printer
.............................. 11
Power On or Off the Everest Encore Printer
............................11
Power On or Off a Standalone Printer ....................................................11
Power On or Off a Printer Connected to an Autoloader or AutoPrinter .11
Place a Disc on the Printer Tray
...............................................11
Set your Printing Preferences
.......................................... 12
Default Printable Area Settings
................................................12
Set Your Printing Preferences
..................................................12
Access Printing Preferences ....................................................................12
Access Printing Preferences through the Windows Start Menu .....................12
Access Printing Preferences through CD Designer .......................................... 12
Access Printing Preferences when Printing PDFs ............................................ 13
Set the Media Type, Media Size, Orientation, and Ribbon Type .............13
Set the Print Quality, Color Matching, and Image Adjustments .............13
Set the Printable Area .............................................................................14
Adjust the Print Alignment and Color Density ........................................14
Check the Ribbon Remaining
...................................................15
View the Ribbon Status ...........................................................................15
Maintaining the Everest Encore Printer
........................... 16
Maintenance Schedule ............................................................16
Change the Print Ribbon
..........................................................16
Remove the Print Ribbon ........................................................................16
Install the Print Ribbon ...........................................................................18
Change the Retransfer Ribbon
.................................................19
Remove the Retransfer Ribbon ...............................................................19
Install the Retransfer Ribbon ..................................................................20
Clean the Everest Encore Printer .............................................20
Clean the Print Head ...............................................................................20
Clean the Tacky Rollers ...........................................................................21
Clean the Rear Air Filter ..........................................................................22
Clean the Side Air Filters ........................................................................23
Clean the Platen Roller ............................................................................24
Clean the Sensors ....................................................................................26
2004001_A For more information visit www.rimage.com/support
Introduction
This manual provides the information needed to operate, configure, and maintain the Rimage Everest Encore™ printer.
For information specific to your autoloader or Rimage AutoPrinter refer to the product’s User Guide found at www.rimage.com/support .
Important!
Your Everest Encore printer may not look exactly like the model featured in this user guide.
About this User Guide
• While we try to maintain all versions of our manuals and documentations, please note that the English version found on our web site always contains the most up-to-date information.
• Unless otherwise indicated, all Windows navigation statements are Windows 10 paths. Other Windows operating system navigation may differ slightly.
• These notes and symbols are used throughout the manual to help clarify information:
Tip: A Tip suggests alternative methods that may not be obvious and helps you understand the benefits and capabilities of the product.
Important!
• An Important note provides information essential to the completion of a task.
•
•
Important supplemental information.
You can disregard information in a Tip and still complete a task, but do not disregard an Important note.
Caution: A Caution indicates that failure to observe this guideline could result in loss or damage to the equipment, product, software, or data.
Warning!
A Warning indicates that failure to follow this guideline could result in bodily injury to personnel operating or maintaining the equipment.
2004001_A
About the Everest Encore Printer
The Everest Encore printer is part of the Rimage series of printers. The printer can be used as a stand alone printer, or with a Rimage autoloader or
Rimage AutoPrinter.
Unpacking and Setup Instructions
Unpacking and installation instructions are included with the Everest Encore printer. Refer to the Rimage Everest Encore Setup and Installation Guide , as well as the setup and installation guide included with your Rimage autoloader or AutoPrinter.
For more information visit www.rimage.com/support 1
Important Information
This section provides support contact information, and cautions and warnings, for the Everest Encore printer.
Technical Specifications for this product can be found at www.rimage.com/ support .
Support Contact Information
US, Canada, Latin America
Rimage Corporation
201 General Mills Blvd, Golden
Valley, MN 55427, USA
Attn: Rimage Services
Email: [email protected]
Telephone:
North America: 800.553.8312
Mexico/Latin America: 952.946.0004 option 2
Fax: 952.944.7808
Europe
Rimage Europe GmbH
Albert-Einstein-Straße 26
63128 Dietzenbach, GERMANY
Email: [email protected]
Telephone: +49 (0)6074.8521.0
Fax: +49 (0)6074.8521.100
Asia/Pacific
Rimage Japan Co., Ltd.
4F Arai #38 Bldg.,
2-7-1 Hamamatsu-cho,
Minato-ku, Tokyo 105-0013, JAPAN
Email: [email protected]
Telephone: +81.3.6452.8780
Fax: +81.3.6452.8785
Rimage Taiwan
2F.-7, No. 508, Sec. 5
Zhongxiao East Rd., Xinyi Dist.,
Taipei City 110, TAIWAN
Email: [email protected]
Telephone: +886.2.2726.0100
Rimage China
RM # 206, 207, 2F
No.1 FuXing Zhong Road
HuangPu District
Shanghai, 200025 CHINA
Email: [email protected] [email protected]
Telephone: +86.021.5887.8905
Contact Rimage Services
Website: www.rimage.com/support
When you contact Rimage
Services, please provide:
• System serial number and software version
• Functional and technical description of the problem
• Exact error message received
Copy and record the following information from your Rimage product for future reference.
Note: Make sure you update the Serial
Number anytime you receive a replacement system .
Serial Number:
Product Name:
Date of Purchase:
Technical Support
Rimage offers a variety of service and support options for the Everest Encore printer including Exchange Services. Please contact your Rimage Value
Added Reseller or Rimage for additional information and pricing.
Optical Disc Recording Software Disclaimer
This Product, Software, or Documentation may be designed to assist you in reproducing material in which you own the copyright or have obtained permission to copy from the copyright owner. Unless you own the copyright or have permission to copy from the copyright owner, you may be violating copyright law and be subject to payment of damages and other remedies. If you are uncertain about your rights, you should contact your legal advisor. If you are neither in possession of the copyright nor have authorization from the owner of the copyright, unauthorized copying of copyrighted material on an optical disc or any other media violates national and international legislation and can result in severe penalties.
2004001_A For more information visit www.rimage.com/support 2
Important Information
Safety and Compliance Information
This manual and the indications on the product allow proper and safe operation. The indication marks below help protect you and other persons from injury, and equipment from damage.
Safety Precautions
To ensure safety, read these precautions and familiarize yourself with their meaning before using the equipment.
Warning!
• Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiant exposure.
• Do not disassemble or use tools on the printer. All service procedures should be performed by a Rimage-authorized technician, or sent in for Rimageauthorized repair.
• Do not service the printer with the power cord plugged in the AC outlet.
• The interior of the printer contains sharp edges.
• The front bezel of the printer can be opened by hand. Do not insert your fingers.
• Do not touch the heat roller.
Country-specific cautions for Wideband Data Transmission systems: 2400-2483.5 MHz
• France: Do not use outdoors.
• Italy: If used outside of own premises, general authorization is required.
• Norway: This subsection does not apply for the geographical area within a radius of 20km from the center of NY-Alesund.
• Use only the supplied AC power cord. Fore more information or to order a new power cord, contact Rimage Customer Service.
• This product is designed for an office environment.
• Do not use the printer if it is overheating or an abnormal smell is detected.
This may result in a fire and an electric shock. In case of heating or abnormal smell, immediately disconnect the cable from the outlet. Contact your Rimage-authorized dealer for repairs.
• Allow sufficient free space for opening the printer tray. Do not touch the printer tray while it is in motion.
• If the side cover is opened while power is supplied, the printer will stop. Do not reach into the printer while it is in operation. Do not attempt to bypass the door interlock.
• This printer has no power switch. Power is disconnected completely by unplugging the cable. Rimage recommends installing the printer in a position that allows immediate disconnection of the power cable. Always hold the plug when disconnecting the cable from the outlet.
• This printer has a voltage slide switch on the back of the unit. Before use, check that is set to the correct voltage. Please do not use any voltage other than 110VAC or 220VAC. This could result in a fire and an electric shock.
• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
Caution:
• All equipment with AC line voltage, or low DC voltages, such as switches, power supplies, fuses, fans, and non-stepper motors, must be replaced with
Rimage-approved components to maintain the safety approval issued by
UL.
2004001_A For more information visit www.rimage.com/support 3
Important Information
Caution:
• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
• “This device complies with Industry Canada’s licence-exempt RSSs.
Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.”
• “Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
1) l’appareil ne doit pas produire de brouillage;
2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.”
2004001_A For more information visit www.rimage.com/support 4
Important Information
Compliance Information
Product Name
Model
Notice for USA
Notice for Canada
Notice for Europe
Notice for Japan
Notice for Australia
Rimage Everest Encore Printer
CDPR23B
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when this equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
This product complies with UL 60950-1, 2nd Edition.
This Class A digital apparatus complies with Canadian ICES-003 Issue 6: 2016, updated April 2017. Cet appareil numerigue de la classe A est conforme a la norme NMB-003 du Canade.
This product complies with CAN/CSA-C22.2 No. 60950-1, 2nd Edition.
This product is in conformity with the EMC Directive 2014/30/EU, Radio Directive 2014/53/EU and the Low-Voltage Directive 2014/35/EU through compliance with the following European Standards: EN55032:2012/AC:2013 Class A Limit; EN55024:2010; EN301 489-17 V3.2.0;
EN301 489-1 V2.2.0; EN300 330 V2.1.1; EN60950-1, 2nd Edition. The CE mark has been affixed in accordance with the CE Marking Directive
93/68/EEC.
This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment
(VCCI). If this equipment is used in a domestic environment, radio interference may occur, in which case, the user may be required to take corrective action.
Translation:
この装置は、情報処理装置等電波障害自主規制協議会（ＶＣＣＩ）の基準に基づくクラスA 情報技術装置です。この装置を家庭環境で使用すると電
波妨害を引き起こすことがあります。この場合には使用者が適切な対策を講ずるよう要求されることがあります。
This product complies with AS/NZS CISPR32:2015.
2004001_A For more information visit www.rimage.com/support 5
Everest Encore Printer Requirements
This section describes ribbon, label design, and print requirements for the
Everest Encore printer.
Ribbon Requirements
Important!
• Rimage only supports the use of Rimage brand ribbons in our printers.
Printer issues that occur as a result of using ribbons from manufacturers other than Rimage are not included under your Rimage warranty or maintenance agreement.
•
•
•
•
For optimum results, make sure that Everest Encore ribbons are stored at a temperature between 41° and 95°F (5° to 35°C) and humidity level between 45% and 85%.
Avoid moisture and direct sunlight.
Do not reuse ribbons.
Use only ribbons designed for the Everest Encore printer. Refer to the table below.
The Everest Encore printer requires a print ribbon and a retransfer ribbon.
The standard print ribbon has three colors: Cyan, Magenta, and Yellow
(CMY). These three colors combine in printing to create full-color discs. Print ribbons are also available in black.
Everest Encore Ribbons
Ribbon Type
3-Color (CMY)
Black (monochrome)
Retransfer ribbon (500 prints)
Number of Discs Printed
500
1000
500
Label Design Requirements
• Label design size – Design labels with a height of 12 cm and width of 12 cm. A full-size disc is 120 mm (4.723”) in diameter. The hole is 15 mm
(0.59”). The printable area and hub sizes vary depending on the disc manufacturer.
Tip: The media that are in Rimage Media Kits have a printable area of
118-24 mm. On most labels, print settings of 118 mm and 24 mm are recommended.
Printable
Area 118 mm
Hub Size
24 mm
• Color mode – If your Everest Encore is on a Rimage autoloader, convert all labels to the RGB color mode in order to import them into
CD Designer. If the Everest Encore is a standalone printer or on an
AutoEverest AutoPrinter, and you are printing directly from an imageediting program, you can work in the color mode of your choice.
• Resolution (pixels per inch) – For best results, use images set to a minimum of 300 pixels per inch. You may notice better results if you use images with 600 pixels per inch or higher.
2001474_A For more information visit rimage.com/support 6
Everest Encore Printer Requirements
Print Requirements
Any label you create and save through CD Designer is in the correct file format (.btw) for printing to an Everest Encore on a Rimage autoloader. You can also print labels saved as PDF files if your Everest Encore is on a Rimage autoloader.
If you are using a standalone Everest Encore printer or an AutoEverest
AutoPrinter, you can print directly from any application with print capability.
2001474_A For more information visit rimage.com/support 7
Identifying the Parts of the Everest Encore Printer
This section describes the Everest Encore printer hardware and features.
Front View
Side Cover Latches
Control Panel
The control panel is located on the front of the Everest Encore.
It includes an operator button and four indicator lights. (One light is on the operator button.) The control panel allows you to monitor and control the printer.
The table below identifies the name and function of all parts of the control panel.
Handle
Side
Cover
Control
Panel
2004001_A
Image
Switches
Name
Operator button
Function
The Operator button is used to complete the following tasks:
• Open the printer tray
Printer
Tray switch and the
Error indicator light
(on the operator button) .
The Error indicator light illuminates when operator action is required.
AC voltage
AC Voltage Switch
The AC voltage switch is used to select the AC voltage of the power outlet.
For more information visit www.rimage.com/support
• Reset after an error
Switch
• Put the printer into sleep mode. To put the printer into sleep mode, press and hold the
Operator button for 10 seconds.
To resume normal operation, press the Operator button again.
8
Identifying the Parts of the Everest Encore Printer
Disc Present indicator light
The Disc Present indicator light illuminates when a disc is placed on the tray or when the disc is properly clamped.
The Disc Present indicator light flashes when there is a problem.
The number of flashes in each cycle indicates the type of problem.
• 1 flash = Side cover is open or ribbon latch 1, 2 or 3 is open
• 2 flashes = Print ribbon problem
(incorrect, missing, or depleted print ribbon)
• 3 flashes = Retransfer ribbon problem (missing or depleted retransfer ribbon)
• 4 flashes = Error upon clamping the disc on the printer tray
Back View
Power
Connector
Active indicator light
Power indicator light
The Active indicator light illuminates when the printer has completed initialization.
The Active indicator light flashes when the printer is receiving data from the host.
The Power indicator light illuminates when the printer is powered on.
Printer Cable
Connector
Original Position of
Shipping Screw
USB Connector
Storage Position for Shipping Screw
Mode Switch
AC Voltage
Switch
2004001_A For more information visit www.rimage.com/support 9
Identifying the Parts of the Everest Printer
Switches
Mode Switch
AC Voltage Switch
There are two switches on the rear of the Everest Encore: the AC voltages switch and the mode switch.
AC Voltage Switch
The AC voltage switch is used to select the AC voltage of the power outlet.
This switch has two positions: 110V and 220V.
Warning! Set the AC voltage switch to match the voltage of the AC power outlet.
Mode Switch
Important!
You must power off the printer before changing the mode.
Power the printer on when the mode switch is set.
The mode switch is a rotary switch used to set the operational mode of the
Everest Encore. The opening at the base of the cap on the switch indicates the selected mode. When the printer is shipped, it is set to the correct mode for your operation. You should not have to change the switch position unless you perform diagnostic tests.
2
3
Switch Position
0
All others
Use
Standalone printer
Rimage autoloader or AutoPrinter
Diagnostic testing
Not used
2004001_A For more information visit www.rimage.com/support 10
Operating the Everest Encore Printer
This section provides the information needed to operate your Everest Encore printer.
Power On or Off the Everest Encore Printer
The Everest Encore printer does not have a power switch. The printer is powered on and off according to your system setup. Refer to the sections below.
Power On or Off a Standalone Printer
Follow these steps for a standalone Everest Encore printer:
• To power on the printer, connect the power cord from the printer to a power outlet.
• To power off the printer, disconnect the power cord from the rear of the printer.
Power On or Off a Printer Connected to an Autoloader or
AutoPrinter
Follow these steps if your Everest Encore is connected to an autoloader or
AutoPrinter:
• To power on the printer, power on the autoloader or AutoPrinter .
• To power off the printer, power off the autoloader or AutoPrinter .
Tip: The printer enters power saving mode if it is idle for more than 30 minutes. When this occurs, the printer takes 2-3 minutes to warm up after a job is sent to the printer.
Place a Disc on the Printer Tray
Use this procedure to place a disc on the printer tray.
1. Press the operator button . The printer tray opens.
2. Place the disc on the print pad . Make sure that the printable surface faces up, and the stacking ring faces the print pad.
Important!
To avoid scratching or damaging the recording surface of the disc, the disc must not rest on the holding pins or the centering pin.
Pad
Centering
Pin
2004001_A
Holding
Pins
For more information visit www.rimage.com/support
Printer Tray
11
Set your Printing Preferences
This section provides the information needed to set up your printing preferences and check the amount of print and retransfer ribbon remaining using a Windows PC.
Default Printable Area Settings
Most discs have the following printable areas:
Disc without stacking ring:
• Outer Diameter 118 mm
• Inner Diameter 24 mm
Disc with stacking ring:
Standard Area:
• Outer Diameter 118 mm
•
•
Inner Diameter 38 mm
Hub Area:
• Outer Diameter 35 mm
Inner Diameter 17 mm
Set Your Printing Preferences
Printing preferences allow you to set up your Everest Encore printer to produce the best possible labels on your discs.
Important : Unless otherwise indicated, all Windows navigation statements are Windows 10 paths. Other Windows operating systems’ navigation may differ slightly.
Access Printing Preferences
Use one of the procedures below to access the Everest Encore Printing
Preferences.
Access Printing Preferences through the Windows Start Menu
Using this method, printing preferences are saved in the printer driver settings and are applied to all newly created labels.
1. Select: Start > Devices and Printers .
2. Right-click the Everest Encore printer . The dropdown menu displays.
3. Select Printing Preferences . The Rimage Everest Encore Printing
Preferences dialog box opens.
Access Printing Preferences through CD Designer
Using this method, printing preferences are saved with the label file and are used instead of the printer driver settings.
1. Open the desired label file in CD Designer.
2. From the File menu, select Print .
The Print window opens.
3. From the Name dropdown list, select the Everest Encore printer .
4. Select the Document Properties button. The Rimage Everest Encore
Properties dialog box opens.
2004001_A For more information visit www.rimage.com/support 12
Set your Printing Preferences
Access Printing Preferences when Printing PDFs
Set the Print Quality, Color Matching, and Image
Adjustments
Use the procedure below to access printing preferences for PDF files.
Important! The procedure below applies only if you are printing PDF labels using a Rimage autoloader. It does not apply if you are using an AutoEverest
AutoPrinter. When you use this procedure, the changes to the settings are global and apply to all PDF labels.
1. Select: Start > Devices and Printers .
1. Access Printing Preferences.
Refer to page 12 for instructions.
2. Select the Advanced tab.
3. View or change the printing preferences.
a. Select the desired Print Quality . (The options are Photo or
Graphics ).
b. Select the desired criteria for Color Matching .
2. Right-click on the Everest Encore printer . The dropdown menu displays.
3. From the dropdown menu, select Printer Properties . The Rimage
Everest Encore Properties dialog box opens.
Tip: The default setting for color matching is Match for CMYK printing .
4. Select the Advanced tab.
5. At the bottom of the Advanced tab, select Printing Defaults… The
Rimage Everest Encore Printing Defaults dialog box opens.
c. From the Image Adjustments dropdown list, select None, High contrast, Vivid colors, or Custom .
If you select Custom , the Settings button becomes active: i. Select the Settings button. The Custom Settings window opens.
Set the Media Type, Media Size, Orientation, and Ribbon
Type
1. Access Printing Preferences.
Refer to page 12 for instructions.
2. Select the Main tab.
3. View or change the printing preferences.
a. Select the appropriate Media Type .
ii. Select the desired Print Threshold Settings .
iii. Move the Contrast Boost slider to adjust the image contrast.
iv. Move the Saturation Boost slider to adjust the image saturation.
v. Select OK to close the Custom Settings window.
b. Select the appropriate Media Size .
c. Select the desired number of Copies .
d. Select the desired Orientation e. Select the appropriate type of
.
Ribbon .
Tip: To modify the printable area, refer to the Set the Printable Area on page 14.
4. Select Apply when you have made the desired choices in the Rimage
Everest Encore Printing Preferences window.
5. Select OK to close the Rimage Everest Encore Printing Preferences window.
4. When you have made the desired choices in the Rimage Everest Encore
Printing Preferences window, select Apply .
5. Select OK to close the Rimage Everest Encore Printing Preferences window.
2004001_A For more information visit www.rimage.com/support 13
Set your Printing Preferences
Set the Printable Area
This functionality allows you to adjust the printable area settings for standard CD/DVD 120 mm media. These settings control the outer and inner diameters so that the label prints on the disc without overlapping the disc edges.
Tip: Printable Area settings created within a CD Designer label file will override the printer and fax settings in Windows.
1. Access Printing Preferences.
Refer to page 12 for instructions.
2. Select the Advanced tab.
3. View or change the Printable Area preferences.
a. Select the Modify button at the bottom of the Advanced tab. The
Printable Area Settings window opens.
b. To modify only Standard Area settings, select the Standard radio button.
i. Enter the desired Outer Diameter .
ii. Enter the desired Inner Diameter .
c. To print on a disc with a stacking ring, select the Advanced radio button. The Hub Area settings display.
i. Enter the desired Outer Diameter for the hub.
ii. Enter the desired Inner Diameter for the hub.
d. Select OK to save the changes. The Printable Area Settings window closes.
e. If necessary, select Default to return to the default f. When you have made the desired choices in the Rimage Everest
Encore Printing Preferences window, select Apply .
4. Select OK to close the Rimage Everest Encore Printing Preferences window.
2004001_A
Adjust the Print Alignment and Color Density
1. Access Printing Preferences.
Refer to page 12 for instructions.
2. Select the Utility tab.
3. Select Status Monitor… button. The Rimage Everest Encore Status
Monitor window opens with the Status tab active.
Tip: On the Status tab, you can view the progress of a print job, the type of print ribbon installed, and the estimated percentages of unused ribbon for the print and retransfer ribbons. To reset the estimate for the number of prints remaining on the ribbons, refer to the View the Ribbon
Status section on page 15.
4. Select the Printer Information tab to view or change the Print Alignment and Color Density settings.
Tips:
• The Printer Information tab also displays the current firmware version and serial number of your Everest Encore printer.
• Select Default to return to the default Print Alignment Settings or
Color Density Settings.
a. View or change the Print Alignment Settings .
i. Select the Modify button from the Print Alignment Settings pane. The Print Alignment Setting s window opens.
ii. Select the desired Color/Monochrome setting in the Horizontal
Alignment Settings pane to modify the horizontal alignment for all ribbon types.
iii. Select the desired Color setting to modify the vertical alignment for prints with a CMY ribbon.
iv. Select the desired Monochrome setting to modify the vertical alignment for prints with a monochrome ribbon.
v. Select OK to save the changes. The Print Alignment Settings window closes.
For more information visit www.rimage.com/support 14
Set your Printing Preferences b. View or change the Color Density Settings .
i. Select the Modify button from the Color Density Settings pane.
The Color Density Settings window opens.
ii. Select the desired Cyan , Magenta and Yellow settings to modify the color density.
iii. Select the desired Black setting to modify the density for monochrome images.
iv. Select OK to save your changes. The Color Density Settings window closes.
5. Select Close to close the Status Monitor dialog box.
6. Select OK to close the Rimage Everest Encore Printing Preferences window.
Check the Ribbon Remaining
The operator panel on Rimage Producer V and Catalyst autoloaders displays the estimated number of prints remaining on the print ribbon and the retransfer ribbon.
For standalone Everest Encore printers and AutoPrinters, you can check the amount of ribbon remaining using the Status feature of the printer driver.
Use the following procedure to check the amount of ribbon remaining for a standalone Everest Encore printer or AutoEverest AutoPrinter.
View the Ribbon Status
The Status tab of the Status Monitor window for Windows allows you to view the estimated percentage and number of prints remaining on the print and retransfer ribbons.
1. Access Printing Preferences . Refer to page 12 for instructions.
2. Select the Utility tab.
3. Select Status Monitor… The Status Monitor window opens, with the
Status tab active.
4. View the ribbon information :
• Current printer status.
• Estimated percentage and number of prints remaining on the print and retransfer ribbons.
Tip: If you remove a ribbon from the Everest Encore printer and reinsert it, the system recognizes the amount of ribbon remaining in the consumable monitoring application. Partially used ribbons from other Everest printers will not display accurately in the consumable monitoring application .
5. Reset the estimate for the number of prints remaining on the retransfer ribbon.
a. Select Options.
The Reset retransfer prints remaining window opens. b. If you are using a 500-print ribbon, check the Use 500 print retransfer ribbon box.
c. Select Reset prints . The Reset prints window opens.
d. Select Yes to confirm the reset. The Reset prints and Reset retransfer prints remaining windows close. e. Select Close to close the Status Monitor window.
f. Select OK to close the Printing Preferences window.
2004001_A For more information visit www.rimage.com/support 15
Maintaining the Everest Encore Printer
You must perform routine maintenance to keep the Everest Encore operating at optimum performance. The table below lists maintenance tasks, frequency, and references to cleaning instructions in this user guide.
Maintenance Schedule
Task Frequency
Change the print ribbon
3-Color
Ribbon (CMY)
After 500 discs
Black Ribbon
(monochrome) After 1000 discs
Change the retransfer ribbon
After 500 discs
Clean the print head After 2000 discs (as needed) or at every ribbon change
Clean the tacky rollers After 2000 discs or at every ribbon change
Clean the sensors Clean the sensors if:
• You receive any of the following error messages stating that the:
Printer is not detecting the print ribbon.
Upper or lower sensor is not responding.
Instructions
Refer to the Change the Print
Ribbon section on page 16.
Refer to the Change the
Retransfer Ribbon section on page 19.
Refer to the Clean the Print Head section on page 20.
Refer to the Clean the Tacky
Rollers section on page 21.
Refer to the Clean the Sensors section on page 26.
Clean the air filters
• The printing is off center.
Monthly
Clean the platen roller Important! Clean the platen roller only if you notice a diminished print quality, such as white specks, on the printed disc.
Clean the exterior Weekly
Refer to the Clean the Rear Air
Filters and Clean the Side Air
Filters sections on page 22,23.
Refer to the
Roller
Clean the Platen
section on page 24.
Wipe the exterior of the printer with a lint-free cloth.
Important! For optimum performance, keep the Everest Encore in a clean, dust-free environment.
Change the Print Ribbon
Before you change or install a new Everest Encore print ribbon, allow time for the new ribbon to become acclimated to the environment. Allow more time for greater temperature and humidity differences.
Important!
• Rimage supports only the use of Rimage brand ribbons in our printers.
Printer issues that occur as a result of using ribbons from manufacturers other than Rimage are not included under your Rimage warranty or maintenance agreement.
• For optimum results, make sure that Everest Encore ribbons are stored at a temperature between 41° and 95°F (5° to 35°C) and humidity level between 45% and 85%.
•
•
•
Avoid moisture and direct sunlight.
Do not reuse ribbons.
Use only ribbons designed for the Everest Encore printer.
Remove the Print Ribbon
Side Cover Latches
1. Open the side cover .
a. Press the two side cover latches to release the side cover.
b. Lower the side cover .
Side Cover
2004001_A For more information visit www.rimage.com/support 16
Maintaining the Everest Encore Printer
2. Access the print ribbon .
Latch 1
Tip: Perform cleaning procedures while the print ribbon is removed. For more information refer to the Clean the Everest Encore Printer section on page 20 .
3. Remove the print ribbon from the carrier.
Take-up Roll
Print Ribbon
Carrier a. Open latch 1 .
b. Pull the print ribbon carrier straight out of the printer.
c. Lay the print ribbon carrier on its back.
Supply Roll a. Slide the supply roll to the left.
b. Slide the take-up roll to the right.
c. Discard the used print ribbon .
2001474_A For more information visit rimage.com/support 17
Install the Print Ribbon
1. Remove the new print ribbon from the packaging.
2. Install the print ribbon on the print ribbon carrier.
a. With the supply roll on the left side, unwind several inches of the print ribbon .
Tacky Roller Guide Rollers e. Rotate the take up roll clockwise so the ribbon is aligned and lies flat. You may need to lift the ribbon up from the tacky roller to straighten it.
Take-up Roll
Take-up Roll
Supply Roll b. Lay the print ribbon across the tacky roller and guide rollers.
c. Install the supply roll as shown.
d. Install the take-up roll as shown.
2004001_A
Important:
• Do not rotate the ribbon past the Cleaning Bars at the front of the ribbon.
• If you installed a monocolor ribbon, advance the ribbon so the ink portion of the ribbon is advanced to the take-up roll.
3. Reassemble the printer .
a. Set the print ribbon carrier upright.
b. Slide the print ribbon carrier into the printer.
c. Close latch 1 .
d. Close the side cover .
Tip: Ribbon color can vary from lot to lot. After you load the new ribbon, you may need to adjust the density settings in the printer driver. Refer to the
Adjust the Print Alignment and Color Density section on page 14.
The printer is ready for use.
For more information visit www.rimage.com/support 18
Change the Retransfer Ribbon
Before you change or first install the Everest Encore retransfer ribbon, allow time for the new ribbon to become acclimated to the environment. Allow more time for greater temperature and humidity differences.
Important!
• Rimage supports only the use of Rimage brand ribbons in our printers.
Printer issues that occur as a result of using ribbons by manufacturers other than Rimage are not included under your Rimage warranty or maintenance agreement.
•
•
For optimum results, make sure that Everest Encore ribbons are stored at a temperature between 41° and 95°F (5° to 35°C) and humidity level between 45% and 85%.
Avoid moisture and direct sunlight.
•
•
Do not reuse ribbons.
Make sure you only use ribbons designed for the Everest Encore printer.
Remove the Retransfer Ribbon
1. Open the side cover .
a. Press the two side cover latches to release the side cover.
b. Lower the side cover .
Side Cover Latches
2. Remove the used retransfer ribbon .
Retransfer
Ribbon Carrier
Retransfer
Rolls
Latch 1
Latch 2 Latch 3 a. Open latches 1, 2, and 3 .
b. Grasp the handle to slide the retransfer ribbon carrier out of the printer.
c. Lift the retransfer rolls out of the carrier.
d. Carefully slide the retransfer ribbon from the retransfer ribbon carrier .
e. Discard the used retransfer ribbon .
2004001_A
Side Cover
For more information visit www.rimage.com/support 19
Install the Retransfer Ribbon
1. Remove the new retransfer ribbon from the packaging.
Supply Roll Take-up Roll
3. Rotate the take-up roll counterclockwise in order to tighten the retransfer ribbon.
4. Reassemble the printer .
a. Slide the retransfer carrier into the printer.
b. Close latches 1 , 2 , and 3 . c. Close the side cover .
The printer is ready for use.
Clean the Everest Encore Printer
Regular cleaning helps to keep your Everest Encore printer in optimal operating condition.
Clean the Print Head
Latch 1 Print Head
Retransfer Ribbon Carrier
2. Position the retransfer ribbon .
a. With the supply roll on the left side, unwind several inches of the retransfer ribbon .
b. Slide the retransfer ribbon under the retransfer ribbon carrier.
c. Install the supply roll on the left side of the retransfer ribbon carrier.
Be sure that the ribbon winds under the supply roll.
d. Bring the take-up roll up and around the guide rollers and snap the roll into place.
2004001_A
#
Tools required:
• Sponge swabs with long handles (included in the Everest cleaning kit)
• 99% Isopropyl alcohol
For more information visit www.rimage.com/support 20
1. Access the print head .
a. Press the two side cover latches to release the side cover.
b. Lower the side cover .
c. Open latch 1 .
d. Remove the print ribbon carrier . For specific instructions, refer to the Change the Print Ribbon procedure on page 16.
2. Clean the print head .
Caution! Do not scratch the print head. Remember the following tips:
• Always wipe from one end of the print head to the other without stopping in the middle.
• Only wipe the area indicated.
a. Apply isopropyl alcohol to the sponge swab .
Print Head Area to Wipe b. Use the sponge swab to wipe across the print head from one end to the other in the direction shown.
c. Repeat as needed until the print head is clean of dust and debris.
d. Use the sponge swab to remove any waxy buildup from the roller below the print head.
3. Prepare the printer for use.
a. Install the print ribbon . For specific instructions, refer to the Change the Print Ribbon procedure on page 16.
b. Install the print ribbon carrier .
c. Close all latches .
d. Close the side cover .
The printer is ready for use.
Clean the Tacky Rollers
#
Tools required:
• Sponge swabs with long handles (included in the Everest cleaning kit)
• 99% Isopropyl alcohol
1. Remove the print ribbon . For specific instructions, refer to the Change the Print Ribbon procedure on page 16.
2. Clean tacky roller 1 (on the print ribbon carrier).
Print Ribbon Carrier
Tacky
Roller 1
Wipe
Direction
Roller
2004001_A For more information visit www.rimage.com/support 21
a. Apply isopropyl alcohol to the sponge swab .
b. Use the sponge swab to clean tacky roller 1 .
c. Use the sponge swab to remove any waxy buildup from other parts of the ribbon carrier .
d. Install the print ribbon on the print ribbon carrier. Refer to the
Change the Print Ribbon procedure on page 16.
3. Inside the printer, use the sponge swab to wipe tacky roller 2 .
Clean the Rear Air Filter
#
Tool Required: Phillips #2 screwdriver
1. Remove the air filter .
Fan Cover Air Filter
Screws
Tacky
Roller 2
4. Prepare the printer for use.
a. Install the print ribbon carrier .
b. Close all latches .
c. Close the side cover .
The printer is ready for use.
a. At the rear of the printer, remove the Phillips screws (Qty. 2) that secure the fan cover.
b. Remove the fan cover .
c. Remove the air filter .
2. Clean the air filter .
a. Hold the air filter under running water.
b. Allow the air filter to dry.
3. Prepare the printer for use.
a. When the air filter is dry, place it inside the fan cover .
b. Insert the screws (Qty. 2) to secure the fan cover to the back of the printer.
The printer is ready for use.
2004001_A For more information visit www.rimage.com/support 22
Clean the Side Air Filters
#
Tool Required: Torx T10 screwdriver
1. Open the side cover .
a. Press the two side cover latches to release the side cover.
3. Remove the three air filters from the fan cover.
4. Clean the air filters .
Air Filters
Side Cover b. Lower the side cover and the attached fan cover .
2. Remove the fan cover from the side cover. a. Remove the Torx T10 screws (Qty. 4) from the inside of the side cover.
b. Close the side cover . The fan cover remains on the work surface, with air filters exposed.
Tip: If the fan cover remains attached to the side cover, gently lower the fan cover.
Fan Cover a. Hold each air filter under running water.
b. Allow the air filters to dry.
2004001_A For more information visit www.rimage.com/support 23
5. Prepare the printer for use.
a. When the air filters are dry, position them on the inside of the fan cover.
b. Make sure that the tabs on the fan cover fit into the holes in the side cover.
Tabs
Side Cover
1. Prepare to clean the platen roller .
a. Power off the printer .
b. At the back of the printer, turn the mode switch to position 3
(diagnostic mode).
c. Power on the printer .
2. Access the platen roller .
a. Press the two side cover latches to release the side cover.
Ribbon Carrier
Retransfer
Ribbon Carrier
Fan Cover c. Open the side cover .
d. Insert and tighten the Torx T10 screws (Qty. 4) to secure the fan cover to the side cover.
e. Close the side cover and the attached fan cover.
The printer is ready for use.
Clean the Platen Roller
Important!
Clean the platen roller only if you notice a diminished print quality, such as white specks on the printed disc.
#
Tools required:
• Sponge swabs with long handles (included in the Everest
Cleaning Kit)
• 99% Isopropyl alcohol
2004001_A
Latch 1
For more information visit www.rimage.com/support
Latch 2 Latch 3
24
b. Lower the side cover . c. Open latches 1, 2, and 3 inside of the printer.
d. Remove the print ribbon carrier. For specific instructions, refer to the Change the Print Ribbon procedure on page 16.
e. Pull out the retransfer ribbon carrier. For specific instructions, refer to the Change the Retransfer Ribbon procedure on page 19.
3. Press and hold the operator button for 2 seconds to access Diagnostic
Test 1. The platen roller begins to rotate and the Active indicator light on the front panel blinks.
4. Clean the platen roller (to the right of the print head).
Platen
Roller a. Remove the sponge swab and the swab handle from the Everest cleaning kit. b. Insert the sponge swab into the unnotched end of the swab handle.
Sponge
Swab
Swab
Handle
Notch
2004001_A
Head c. Apply isopropyl alcohol to the sponge swab .
d. As the platen roller rotates, use the sponge swab to wipe the platen roller .
Caution! Do not apply pressure when cleaning the platen roller with the sponge swabs. Applying pressure may damage the platen roller, leaving scratch marks on the printed disc.
Tip: As you wipe the platen roller, allow it to rotate a full turn before moving to the next area.
5. Press and release the operator button to exit diagnostics mode.
6. Prepare the printer for use.
a. Power off the printer .
b. Install the print ribbon carrier .
For more information visit www.rimage.com/support 25
c. Install the retransfer ribbon carrier.
d. Close all latches.
e. Close the side cover .
f. Turn the mode switch to the correct operating position.
For more information, refer to the Switches section on page 10.
g. Power on the printer .
The printer is ready for use.
Clean the Sensors
When should you clean the sensors?
• You receive an error message stating that the printer is not detecting the print ribbon.
• You receive an error message stating that the upper sensor is not responding.
• You receive an error message stating that the lower sensor is not responding.
• The printing is off center.
#
Tools Required
• Sponge swabs with long handles (included in the
Everest cleaning kit)
• Can of compressed air
1. Access the sensors .
a. Press the two side cover latches to release the side cover.
b. Lower the side cover .
c. Open latch 1 .
d. Remove the print ribbon carrier . For specific instructions, refer to the Remove the Print Ribbon procedure on page 16.
e. Remove the retransfer ribbon carrier. For specific instructions, refer to the Remove the Retransfer Ribbon procedure on page 19.
2. Power off the printer, autoloader or AutoPrinter . Refer to the Power On and Off the Everest Encore Printer section on page 11 for instructions.
Important!
Do not clean the printer sensors until the printer is completely powered off.
3. Locate the sensors .
• Print ribbon sensor
• Upper sensor
• Lower sensor
Ribbon
Sensor Upper
Sensor
Lower
Sensor
2004001_A For more information visit www.rimage.com/support 26
4. Locate the swab handle found in the Everest Cleaning Kit. Remove the sponge swab from the swab handle if necessary.
Sponge
Swab
Swab
Handle
Notch
Tip: One end of the handle has a slot with a notch in it approximately ¼ inches from the end. This is the end that goes into the printer.
5. Clean the sensors .
a. Position the slotted end of the swab handle by the sensor. Refer to page 26 for the sensors’ location. b. Position the can of compressed air’s nozzle in the unnotched end of the handle.
c. Blow compressed air in to the end of the handle for one to two seconds.
d. Repeat two to three times.
e. Repeat for each of the three sensors.
6. Prepare the Printer for use.
a. Replace the print ribbon carrier .
b. Replace the retransfer ribbon carrier .
c. Close the latches .
d. Close the cover .
The printer is ready for use.
2004001_A For more information visit www.rimage.com/support 27
advertisement
Related manuals
advertisement