Euro-Pro 1100H Dressmaker Instruction Manual

TROUBLE SHOOTING
1.The sewing machine does not run when the power switch is pressed.
* Batteries are inserted incorrectly.Re-insert using the diagram provided
inside the battery compartment.
+ Batteries are exhausted. Replaced with new ones.
* Make sure the Adapter(6V,1.2A) €: foot controller connected in the right
position: &—¢—®
2.The sewing machie runs, but does form stitches,
* Incorrectly threaded Re-thread machine.
* Needle is incorrectly threaded. Make sure thread is threaded from left to right.
* Needle is not properly inserted.
* Batteries are installed incorrectly. Check the diagram in the battery
compartment & re-install.
» Caution: To remove fabric after sewing, first turn the handwheel to raise the
needle to the highest position. Lift the Presser Foot & remove the fabric. This
will avoid of bending the needle.
3.The machine runs slowly.
+ Used batteries & new batteries are used together. Replace with the new
batteries.
- Use only AA(#3,1.5V) batteries.
4.The sewing machine stops sewing.
* Very heavy fabric or too many layers of fabric will force the sewing machine
to stop.
* Thread is tangled in the lower bobbin. Stop the machine. Cut the tangled
threads to clear it from the machine. Re-thread both the bobbin and the needle.
» Poor quality stitching: refer to "Adjust Thread Tension"
* When new batteries are installed, the sewing machine should work for
approximately 2 hours under normal sewing conditions. Remember that
heavy fabric requires more power, so it will reduce the running time of the
batteries.
Dressma ker
INSTRUCTION MANUAL
Please read the instruction manual carefully before
operating the sewing machine.
For information or assistance:
Para más información o asistencia:
Pour plus d'information ou pour obtenir de l'assistance:
EURO-PRO Operating LLC
U.S.: 94 Main Mill Street, Door 16, Canada: 4400, Bois-Franc
Plattsburgh, NY 12901
Tél.: (800) 361-4639
St-Laurent, QC H4S 1A7
EURO-PRO Operating LLC - All rights reserved
EURO-PRO Operating LLC - Tous droits réservés
Modele 1100H
EURO-PRO X
Guarantee Bond
This guarantee applies to defects resulting from imperfections
in manufacture of parts entering into the manufacture and
assembly of the sewing machine which this bond
accompanies, for a period of one (1) year, subject to the
following conditions, exclusions and exceptions.
This guarantee is enforceable if said sewing machine is given
reasonably good care and proper maintenance in accordance
with the accompanying printed instructions.
Needles, lamp bulb, and bobbins which normally require
replacement are not covered under this warranty.
Your exclusive remedy for any losses or damages resulting
from defects in both performance, workmanship and materials
of this product shall be the repair or replacement of this product.
The manufacturer shall not be liable for consequential or
incidential damages for breach of any express or implied
warranty of this product.
This guarantee is extend only to the original purchaser of the
machine and this guarantee excludes all other legal and/or
conventional guarantees. The only responsibility of EURO -
PRO Operating LLC, if any, is in relation to the specific
obligations expressly assumed by it under the terms of this
guarantee bond.
For repairs or replacement, send to:
U.S:: 94 Main Mill Street, Door 16, Plattsburgh, NY 12901, Tel.: (800)361-4639
Canada: 4400 Bois Franc, St. Laurent, Quebec, H4S 1A7, Tel.: (800) 361-4639
Please include proof of purchase and $ 8.95 to cover cost of
return shipping & handling.
printed in China Rev.03/04
GETTING STARTED
Bobbins ail spool
SS =
Rewinding |
spool pin \ / Needle
WE
Adaptor Foot Control Threader
BATTERY INSTALLATION
1.Battery compartment is on the bottom of sewing
machine.
2.Open the cover of battery compartment and place
4"AA"alkaline battery as the diagram provided.
Make sure the batteries are in the right polarities
marked on the machine.
3.Replace the cover.
Caution : Make sure that the power switch is in the
OFF position when changing the batteries. If you
install the batteries when the power is ON , the
machine may run suddenly.
THREADING UPPER THREAD
uz:
.
Caution: When threading the machine,
make sure the power switch is OFF.
1.Put the bobbin into the spool pin.
2.Thread following the numbers 1-2-3-4-5-6
3.Needle must be threaded from left to right.
REPLACE THE LOWER BOBBIN
+
3
Caution: When replacing the lower bobbin,
make sure the power switch is OFF.
1.Slide the bobbin cover to the left and
pull it out.
2.Remove the bobbin from the case.
3.Place the new bobbin in compartment,
leaving a 3" tail.
4.Hold the end of the upper thread with the
left hand, and turn the handwheel slowly
anti-clockwise until the needle goes down
and up again to its highest position. Pull
the upper thread slowly and the lower
thread will be coming up in a loop. Pull
up both threads to the back and place
them together under the presser foot.
5.Replace the bobbin cover.
0
CAUTION
1.Don't press the power switch & Foot Control at the same time.
2.Don't use the batteries & the adaptor at the same time.
3.Make sure the batteries are in the correct position.
4.Don't keep the machine running for too long.
5.Sewing some very stretchy fabrics might result in skipping stitches-use
stretch needle.
6.Adaptor (6V) or 4 size "AA" batteries(1.5V)
The machine provides 2-speed sewing
(faster & normal).To run the machine at
the faster speed press the speed control
switch. Press the Speed switch again to
return to normal speed.
Large spool pin
(for winding
Spool pin
(for rewinding)
1.Remove the lower bobbin from the bobbin
holder.
2.Pull up short spool pin and metal bobbin
on top of machine, then replace a large
spool of thread on it by insert a large
spool pin.
3.Put the bobbin to be filled on the bobbin
winding pin and wrap thread counter-
clockwise around the bobbin several
times. (pay attention to the direction of
threading)
4 Depress the power switch and run until the
bobbin is full. Use your finger to control the
thread winding up and down. Press the
switch again to stop and remove the bobbin.
Caution:Remove batteries and/or disconnect
the adaptor before starting to replace needle.
1. Turning the handwheel anti-clockwise to
raise up the needle to its highest position.
Hold the old needle and loosen the needle
clamp screw. Remove the old needle and
discard responsibly. (See diagram )
2.Insert the new needle into the clamp with
the flat side toward the right. Be sure to
push the needle all the way up into the
needle clamp before tightening the needle
clamp screw.
3.Tighten the needle clamp screw.
4. The needle type recommended is size 90/14
house-use needle or equivalent.
1.Turn the handwheel to raise up the
needle to the highest position, lift the
presser foot and place the fabric under
the presser foot.(see diagram 1)
2.Lower the presser foot (see diagram 2)
3.Press the power switch and begin
sewing. Don't pull the fabric.
4 After finishing sewing, press the power
switch again to stop sewing.
(See diagram 3)
5.Rotate the handwheel to bring the needle
to the highest position. Lift up the presser
foot and gently pull the fabric away from
the machine.(see diagram 4)
1.Sewing back over the seam at the
beginning and end will secure the
stitches and strengthen the seam.
2.When reverse sewing is required,
simply press the reverse button.
3.Don't press the Reverse Button
down too much, otherwise it will
cause too long a stitch length.
1.1f additional light is required, press the
switch to turn the light on, press the
switch again to turn the light off.
Before sewing your item, test for the
correct stitch length, using a piece of fabric.
The machine can provide three-stitch length.
As shown in the figure, when the dial is
adjusted in the position 1, the stitch is in
shortest. When the dial is at the position 3.
the stitch length is in its longest position.
Normally we suggest you to adjust it in
the position 2.
A correctly adjusted seam has the upper and the lower threads even and the
junction in the middle of the fabric. (see the illustration)
PPER THREAD
1.1f the upper thread (visible on the
top of the cloth)become a straight line,
turn the thread tension dial anti-clockwise
to obtain a balanced stitch.(see the figure)
FABRIC
A я я A À n
OWER THREAD
2.1f the lower thread (visible on the
underside) become a straight line, turn
the thread tension dial clockwise until you
obtain a balanced stitch.
PPER THREAD FABRIC
WUVULC
LOWER THREAD