Mazda CX-3

2016-2020

Toyota Yaris

2019-2020

Visit MetraOnline.com

for more detailed information about the product and up-to-date vehicle specific applications

KIT FEATURES

• ISO DDIN radio provision †

• Pioneer modular DDIN radio provision ‡

† Kit designed for “L” shaped aftermarket radio, with chassis at bottom

‡ Pioneer radios DMH-C2550NEX and DMH-C2500NEX

KIT COMPONENTS

• A) Trim panel • B) Back panel • C) Radio bracket • D) Pioneer brackets • E) Panel clips (2) • F) Flat-head radio screws (8)

A B C D E

F

107-MZ1B

I N S TA L L AT I O N I N S T R U C T I O N S

U.S. Patent Pending

TABLE OF CONTENTS

Dash Disassembly ..................................................2

Kit Preparation .......................................................3

Kit Assembly

–ISO DDIN radio provision .................................4-5

–Pioneer modular DDIN radio provision ......... 6-7

WIRING & ANTENNA CONNECTIONS (sold separately)

Wire harness: 70-7903L, 70-7905

Antenna adapter: 40-HD10L

Steering wheel control:

Go to AXXESSINTERFACES.COM for options

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver

• 10mm Socket wrench

Attention!

Let the vehicle sit with the key out of the ignition for a few minutes before removing the factory radio. When testing the aftermarket equipment, ensure that all factory equipment is connected before cycling the key to ignition.

Metra. The World’s Best Kits.

® MetraOnline.com

© COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 9/17/20 INST107-MZ1B

1.

Unclip and remove the panel on the top of the dash behind the radio display.

(Figure A)

2.

Unclip and remove the panel on the top of the dash in front of the radio display.

(Figure B)

3.

Remove (2) 10mm bolts securing the radio. Slide the radio out, then unplug and remove. (Figure C)

Continue to Kit Preparation (Figure A)

DASH DISASSEMBLY

(Figure B) (Figure C)

2 1.800.221.0932 | MetraOnline.com

1.

Attach (2) panel clips provided to the radio bracket . (Figure A)

Continue to Kit Assembly

KIT PREPARATION

(Figure A)

REV. 9/17/2020 INST107-MZ1B 3

ISO DDIN radio provision

1.

Secure the radio bracket to the radio using screws supplied with the radio. (Figure A)

Note: Radio chassis screws must be flush.

Screws are provided if needed.

2.

Slide the radio bracket assembly into the dash opening. The rear of the bracket should go into the rear support slot in the dash. (Figure B)

3.

Secure at the front with the factory hardware. (Figure B)

4.

Clip the back panel over the radio.

(Figure C)

Continued on the next page

(Figure A)

KIT ASSEMBLY

(Figure B) (Figure C)

4 1.800.221.0932 | MetraOnline.com

5.

Clip the panel in front of the radio to the dash. (Figure D)

6.

Clip the trim panel to the back panel over the face of the radio. (Figure E)

KIT ASSEMBLY

(CONT.)

(Figure D) (Figure E)

REV. 9/17/2020 INST107-MZ1B 5

Pioneer Modular DDIN radio provision

Note: For step 1 reference the installation manual provided with the radio for which hardware to use. The display screen and radio chassis use two different types of screws.

1.

Secure the Pioneer chassis and display screen to the Pioneer brackets using (8) screws supplied with the radio.

(Figures A and B)

2.

Connect the RGB extension cable to the display and chassis.

3.

Secure the radio bracket to the radio using screws supplied with the radio. (Figure C)

Note: Radio chassis screws must be flush.

Screws are provided if needed.

Continued on the next page

(Figure A)

6

KIT ASSEMBLY

(Figure B) (Figure C)

1.800.221.0932 | MetraOnline.com

4.

Slide the radio bracket assembly into the dash opening. The rear of the bracket should go into the rear support slot in the dash. (Figure D)

5.

Secure at the front with the factory hardware. (Figure D)

6.

Clip the back panel over the radio.

(Figure E)

(Figure D)

KIT ASSEMBLY

(CONT.)

7.

Clip the panel in front of the radio to the dash. (Figure F)

8.

Clip the trim panel to the back panel over the face of the radio. Clip the panel in front of the radio to the dash. (Figure G)

(Figure F)

(Figure E) (Figure G)

REV. 9/17/2020 INST107-MZ1B 7

Metra. The World’s Best Kits.

® MetraOnline.com

107-MZ1B

I N S TA L L AT I O N I N S T R U C T I O N S

Having difficulties? We’re here to help.

Contact our Tech Support line at:

386-257-1187

Or via email at: [email protected]

Tech Support Hours (Eastern Standard Time)

Monday - Friday: 9:00 AM - 7:00 PM

Saturday: 10:00 AM - 7:00 PM

Sunday: 10:00 AM - 4:00 PM

® K NOWLEDGE IS P OWER

E nhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry.

Log onto www.installerinstitute.com or call

800-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians

© COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 9/17/20 INST107-MZ1B