View Manager

®

16 Plus

Quick Reference Guide

1

RCTT16BE Enhanced T

OUCH

T

RACKER

®

Overview

Displays the Dome's ID Code.

Initiates the currently selected

SpeedDome's Apple Peel pattern.

Displays currently selected camera number,

Quick View number or Pattern number.

Also displays system prompts and messages.

Toggles the state of the dome's output.

Invokes the menu.

Clears the last keypad entry or active alarm.

Opens or closes the camera's iris, making the image on the monitor appear darker or lighter.

Sequences through the available monitor display modes: 2x2, 3x3,

4x4, and full-screen.

Controls the camera's zoom function.

B

A

Men u

Iris

Outp On ut

Off

Clea r

Clos e

Open

Info

Peel

7

0

4

8

1

2

3

5

6

Flip

View

9

Previo us

Next

Patte rn

Patte at rn

Seq

D

C

Enters the number of the Camera,

Quick View, Pattern, or Output.

Flips the currently selected SpeedDome

180º.

Calls up a Quick View.

Calls up a Pattern one time.

Repeats a Pattern indefinitely.

Initiates the Sequence.

Controls the camera's pan and tilt function.

Also allows you to interface with the menu.

New and Improved Features

The enhanced TOUCH TRACKER allows you to customize the following features:

• LCD backlight brightness

• Volume control for key click

• Turn key click On or Off

Enables you to step through the installed cameras—one at a time—in sequential order.

Calls up video from a specific camera.

Controls the camera's focus function.

In addition, the following features have changed to improve the usability and reliability of the Touch Tracker:

• Larger, hard plastic keys

− Number

− Function

− Camera and Monitor keys (with icons)

• New Tracker Ball and mechanism

− Eliminates need for calibration

• Microswitch zoom and focus keys

• Updated color scheme

8000-2654-01, Rev. A1 (4 pages) SENSORVISON PRODUCTS 1

LCD Menu

Define Sequence

Setup View

Record Pattern

Alarm Actions

Config Devices

Reset Dome

Select Language

Tog Primary / 2nd

Tog Zoom / Focus

Adjust V-Phase

Show Sys Info

Ping Dome / TTR

Adj Backlighting

Adj Keyclick Vol

Keyclick ON/OFF

Press the Menu button on the keypad to invoke the menu. This scrollable menu appears on the LCD. Only two menu selections are visible at one time on the LCD.

Move the Tracker Ball up and down to scroll through the menu selections. To select the item on the top line of the

LCD (in this example Define Sequence), press a Zoom button. To select the item on the bottom line of the LCD

(in this example Setup View) press a Focus button.

Apple Peel

The “Apple Peel” consists of three revolutions of camera panning, with tilt starting at the ceiling line. Each revolution tilts down approximately 30°. The Apple Peel will provide you with a complete view of the area.

APPLE PEEL PATTERN

Press the number of the camera whose video you want to display full-screen, then press button).

( Camera

Sequence through the

Cameras

To display all of the available cameras—one at a time— in sequential order, press the Previous and Next buttons. Each time you press Previous , the previous camera is displayed. Each time you press Next , the next camera is displayed.

Select the Monitor Display

Format

If you are connected to a quad splitter or multiplexer, you can specify the monitor display format:

• Full-screen

• 2X2 (for quad splitters and 4, 9, and 16-camera multiplexers)

• 3X3 (for 9 and 16-camera multiplexers)

• 4X4 (for 16-camera multiplexers)

Press ( Display button) to sequence through the available display formats. For quad splitters, the Display button switches between Quad A (cameras 1-4) and

Quad B (cameras 5-8).

“Flip” the SpeedDome

To flip the currently selected SpeedDome 180° in the opposite direction, press Flip .

Run “Apple Peel”

To instruct the currently selected SpeedDome to run the

Apple Peel pattern, press Peel .

The Apple Peel pattern will repeat itself indefinitely until you issue a camera command (pan, tilt, zoom or focus) to the dome running the pattern.

RCTT16BE / VM16 PLUS ENHANCED TOUCH TRACKER

8000-2654-01, REV. A1

Clear an Alarm

To clear the alarm whose information appears on the

LCD press Clear .

Control Dome Outputs

1. Refer to the Dome Input / Output chart to see which outputs are connected to which domes, and what the on / off states are for those domes.

2. Press the number of the camera whose output you want to turn on or off, then press Camera .

3. Press the number of the output (1 - 4) that you want to turn on or off.

4. Press Output On to turn the Output on; press

Output Off to turn the Output off.

Display a Quick View

Note : SpeedDome Ultra III supports 96 views. Other domes support 4 views.

1. Press the number of the camera whose Quick View you want to display, then press Camera .

2. Press the number of the Quick View you want to display (1 - 96), and then press View .

Run a Pattern

1. Press the number of the camera whose Pattern you want to display, then press Camera .

2. Press the number of the Pattern you want to display

(1 - 3), then press Pattern (if you want the pattern to run one time only) or Repeat Pattern (if you want the

Pattern to repeat itself indefinitely).

If you select a repeating Pattern, the Pattern will repeat itself until you issue a camera command (pan, tilt zoom or focus) to the dome running the Pattern.

Run the Sequence

To initiate the pre-defined Sequence, press Seq . The

Sequence will repeat itself indefinitely until you press

Seq or Clear .

Define a Quick View

Note : SpeedDome Ultra III and newer domes supports

96 views. Other domes support 4 views.

1. On the monitor, display the picture for which you want to create a quick view.

2. Press Menu to display the LCD Menu. Use the

Tracker Ball to scroll through the choices.

3. Press Zoom or Focus to select Setup View .

4. Press the number buttons (1 - 96) that you want to assign to this Quick View.

5. Press Zoom or Focus to save.

Define a Pattern

1. On the monitor, display the picture that you want to be the starting point of the Pattern.

2. Press Menu to display the LCD Menu. Use the

Tracker Ball to scroll through the choices.

3. Press Zoom or Focus to select Record Pattern .

4. Press the number (1 - 3) that you want to assign to this pattern.

5. Move the camera around, zoom and focus as necessary to create a logical camera pattern.

If you make a mistake during programming and no longer want to program the pattern, press Clear .

6. When you complete creating the pattern, press Next .

SpeedDome LT Auto Pan

Programming

1. On the monitor, display the picture that you want to be the starting point of the Auto Pan.

2. Press Menu to display the LCD Menu. Use the

Tracker Ball to scroll through the choices.

3. Press Zoom or Focus to select Record Pattern .

4. Press the number 1 on the keypad.

5. Move the camera to the end point, then press Next .

When you select Pattern 1 for this dome, the camera will pan smoothly from side-to-side until another camera command is issued.

RCTT16BE / VM16 PLUS ENHANCED TOUCH TRACKER

8000-2654-01, REV. A1

Define the Sequence

1. Press Menu to display the LCD Menu. Use the

Tracker Ball to scroll through the choices.

2. Press Zoom or Focus to select Define Sequence .

3. Use the Tracker Ball to scroll through the list of events until the event you want to define or re-define appears on the LCD.

4. In the Cam field, indicate which camera this event was defined on (use the number buttons).

5. In the Act field, indicate the kind of Action you are specifying for this event. Press View for a Quick

View; press Pattern for a Pattern. For a fixed shot, press Clear to leave this field blank.

6. If the action is a Quick View or Pattern, enter the specific Quick View or Pattern number (use the number buttons).

7. In the Dur field, indicate the duration time for this event (use the number buttons).

8. Repeat steps 3 through 7 for each event to be defined in the sequence.

Adjust LCD Backlighting

1. Press Menu to display the LCD Menu. Use the

Tracker Ball to scroll through the choices.

2. Press Zoom or Focus to select Adj

Backlighting .

3. Press Next to make the backlighting brighter; press

Previous to make the backlighting dimmer.

Adjust Key Click Volume

1. Press Menu to display the LCD Menu. Use the

Tracker Ball to scroll through the choices.

2. Press Zoom or Focus to select Adj Keyclick

Vol .

3. Press Previous to make the volume softer; press

Next to make the volume louder.

Turn Key Click On / Off

1. Press Menu to display the LCD Menu. Use the

Tracker Ball to scroll through the choices.

2. Press Zoom or Focus to select Key Click

On/Off .

3. Press Next to turn the key click on or off. The current setting appears on the LCD.

− If the key click is on, Keyclick ON appears on the LCD.

− If the key click is off, Keyclick OFF appears on the LCD.

1. Press Menu to display the LCD Menu. Use the

Tracker Ball to scroll through the choices.

2. Press Zoom or Focus to select Select Language .

3. Use the Tracker Ball to scroll through the language selections.

4. Press Zoom or Focus to select the correct language.

The enhanced T OUCH T RACKER supports the following languages:

− English

− Dutch

− German

− French

− Hungarian

− Italian

− Japanese

− Portuguese

− Spanish

− Swedish

View Manager and T

OUCH

T

RACKER

are trademarks of Sensormatic

Electronics Corporation. Other product names (if any) mentioned herein may be trademarks or registered trademarks of Sensormatic or other companies.

No part of this guide may be reproduced in any form without written permission from Sensormatic Electronics Corporation.

© 2005 Sensormatic Electronics Corp. All rights reserved.

RLJ 5/05

RCTT16BE / VM16 PLUS ENHANCED TOUCH TRACKER

8000-2654-01, REV. A1