advertisement
FPA405
INSTRUCTION MANUAL
We’ll Make It Stress-Free
If you have any questions along the way, just give us a call:
1-888-333-9952 (UK: 0800-056-2853) we’re ready to help!
2
IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS – PLEASE READ ENTIRE MANUAL PRIOR TO USE
Before You Begin
Please check the following items:
Your TV and any accessories you plan to use do not exceed the specifi ed weight limit of your TV mount.
You read and understand these directions.
You refer to the documentation that came with your TV for additional guidance.
You have the tools needed for installation.
If your TV bracket has built-in or integrated spacers (see
Figure 1), or mounting holes or slots that are wider than
11mm [.43 in.] (see Figure 2), you cannot use this product.
Call Customer Service for assistance.
Figure 1
<11mm
[.43 in.]
Figure 2
WARNING:
•
This product is only designed to be used with Sanus VuePoint television mounts and mounted BELOW the television.
•
This soundbar mount was designed to be installed and utilized
ONLY as specifi ed in this manual. The manufacturer is not responsible for improper assembly, use, or handling of this product.
•
The wall must be capable of supporting fi ve times the weight of the TV, mount, and soundbar combined.
•
Failure to follow these instructions could result in an unstable situation that may result in property damage or personal injury.
Please contact Customer Service with any questions.
3
Weight Limit for the FPA405 Items Needed
Phillips Screwdriver
15 lb (6.8 kg)
DO NOT EXCEED!
Level
CAUTION:
Avoid potential personal injuries and property damage!
You must verify that the weight of the TV plus the soundbar mount, soundbar, and any accessories is lower than the maximum weight rating of the
TV mount.
4
SANUS VUEPOINT TELEVISION MOUNT
Arm Position
05
NOTE:
TV/bracket arms
05
should be positioned as vertically as possible.
05
05
5
Supplied Parts and Hardware
WARNING:
This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service. Never use damaged parts!
NOTE: Not all hardware included will be used.
Parts and Hardware for STEP 1 (and 3)
Soundbar Bracket Arm “C” Washer
Keyhole Screw
Knob
6
01
x 2
02
x 2
03
x 2
04
x 4
Parts and Hardware for STEP 3
TV Bracket Arm
Hardware for TV Bracket
TV Screw Washers
05
x 2
Mount Spacer
M4/M5
07
x 4
M6/M8
08
x 4
06
x 2
Large M4/M5
09
x 4
Large M6/M8
10
x 4
7
8
Hardware for TV Bracket
Screws for TVs with a Flat/Unobstructed Back
M4 x 16mm
11
x 4
M5 x 16mm
12
x 4
M6 x 16mm
13
x 4
M6 x 25mm
14
x 4
M8 x 20mm
15
x 4
Hardware for TV Bracket
Screws for TVs with Irregular/Obstructed Backs
M4 x 40mm
16
x 4
M5 x 40mm
17
x 4
M6 x 40mm
18
x 4
M8 x 40mm
20
x 4
M6 x 50mm
19
x 4
Spacer for TVs with Irregular/
Obstructed Backs
21
x 4
9
STEP 1
Mount Bracket Arms to Soundbar - Option 1
Check the compatibility of the soundbar bracket with your soundbar.
Assemble knobs
04
and screws
03
.
Attach the soundbar arms
01
to soundbar. Do not fully tighten the knobs
04
.
NOTE:
When planning on the position of the soundbar, make sure you will be able to access the control buttons.
04
03
10
01
04
03
01
11
STEP 1
Mount Bracket Arms to Soundbar - Option 2
Check the compatibility of the soundbar bracket with your soundbar.
Assemble knobs
04
and screws
03
.
Some connections to the soundbar may require a “C” washer soundbar arms
02
to ensure that the
01
lay fl at on the soundbar. If required, slip a “C” washer
02
onto the knob screws
03
and under the arms
01
and loosely tighten the knobs
04
.
04
03
12
04
01
02
04
02
03
02
04
01
13
STEP 1
Mount Bracket Arms to Hanger - Option 3
Some soundbars will come with a manufacturer supplied hanger.
Attach the soundbar arms
01
to the soundbar hanger with knobs
04
and screws
03
.
Do not fully tighten the knobs
04
.
14
01
SOUNDBAR
MANUFACTURER
SUPPLIED HANGER
04
03
01
15
STEP 2
Prepare TV
If your TV is already mounted:
A.
Remove any cables attached to the TV.
B.
Remove the TV/bracket assembly from the wall plate, arm assembly, or pillar. Please see your
TV wall mount installation manual for guidance.
A
HEAVY! You may need assistance with this step!
C.
Remove the TV bracket from the TV.
IMPORTANT!
! Please see your TV wall mount manual for instructions on how to remove the TV
16
interface bracket.
! Save the TV hardware in case you want to use the TV
without the soundbar in the future.
! You must use the hardware provided with this product instead of the hardware that came with your mount.
B
C
17
STEP 3
Install TV Bracket with the TV/Bracket Arms
Determine the bolt diameter for your monitor and your TV type - M4, M5, M6, or M8.
Step 3-1 Step 3-2
• For TVs with a fl at/unobstructed back, see
Step 3-1
• For TVs with an irregular/obstructed back, see Step 3-2
If you need extra space to accommodate cables, recesses, or protrusions, see Step 3-2 that uses spacers.
Standard confi gurations are shown. For special applications, contact Customer Service.
CAUTION:
Use the shortest screw and spacer combination needed to accommodate cables, recesses, or protrusions. Using hardware
that is too long may damage your monitor’s internal components!
18
STEP 3-1
06
06
11 12 13 14 15
07 08 09 10
WARNING:
You must use the larger washers
09
or
10
unless they do not fi t your tv bracket.
05
NOTE:
Soundbar must be mounted below the TV as shown.
19
20
STEP 3-2
06
06
05
16 17 18 19 20
07 08 09 10
WARNING:
You must use the larger washers
09
or
10
unless they do not fi t your tv bracket.
21
NOTE:
Soundbar must be mounted below the TV as shown.
CAUTION:
The end of the TV/bracket arms
05
must not extend beyond the edge of the TV.
05
05
21
STEP 4
Attach Soundbar Assembly to TV
Attach the soundbar/bracket arm
01
assembly to the TV/bracket arms
05
using knobs
04
. Do not completely tighten the connections.
NOTE:
You may need to use trial and error to get the soundbar TV brackets set to the right confi guration.
22
Options 1 and 2
04
05
04
01
01
Option 3
04
05
04
05
05
01
01
23
STEP 5
Adjust Arms
Adjust the soundbar/bracket arms
01
and the TV/bracket arms
05
until soundbar or hanger is the in desired position.
NOTE:
Final position of soundbar must be within 51 mm (2 in.) of the TV.
24
≤51 mm (2 in.)
05
01
25
STEP 6
Tighten Connections
When soundbar or hanger is in the desired position, tighten all connections.
26
STEP 7
Hang Assembly
Follow your TV wall mount installation manual to re-hang the assembly.
Options 1 and 2 Option 3
27
ESPAÑOL
INSTRUCCIONES DE SEGURIDAD IMPORTANTES. CONSÉRVELAS. LEA TODO EL MANUAL ANTES DE UTILIZAR ESTE PRODUCTO.
Antes de comenzar
Revise los siguientes puntos:
Que su televisor y cualquier accesorio que vaya a utilizar no excedan el límite de peso especificado del soporte del televisor.
Que va a leer y que comprende estas indicaciones.
Que va a consultarla documentación que viene con su televisor para ver otras instrucciones.
Que tiene las herramientas necesarias para la instalación.
Si la placa de sujeción tiene separadores incorporados o integrados (ver Figura 1) u orificios o ranuras de montaje más anchos que 11 mm [43 pulg.] (ver Figura 2), no debe usar este producto. Comuníquese con el Servicio de Atención al Cliente para recibir ayuda.
28
ESPAÑOL
ADVERTENCIA:
•
Este producto fue diseñado para usarse únicamente con soportes para televisores Sanus VuePoint y deben colocarse DEBAJO del televisor.
•
Este soporte para barra de sonido fue diseñado para instalarse y utilizarse
SOLO como se especifica en este manual. El fabricante no se hace responsable por el armado, manipulación o uso incorrectos de este producto.
•
La pared debe soportar cinco veces el peso del televisor, del soporte y de la barra de sonido juntos.
•
No seguir estas instrucciones podría ocasionar una situación inestable que puede causar daños materiales o lesiones físicas.
Comuníquese con el Servicio de Atención al Cliente si tiene alguna pregunta.
29
ESPAÑOL
Límite de peso para el FPA405
6,8 kg (15 libras)
¡NO LO EXCEDA!
PRECAUCIÓN:
Evite lesiones y daños materiales.
Debe verificar que el peso del televisor, junto con el soporte para la barra de sonido y los accesorios sea menor que el peso máximo permitido para el soporte del televisor.
Piezas necesarias
Destornillador Phillips Nivel
30
SOPORTE PARA TELEVISOR SANUS VUEPOINT
Posición del brazo
NOTA:
Los brazos del módulo televisor-placas
05
deben colocarse lo más verticales posible.
Piezas y accesorios suministrados
ADVERTENCIA:
Este producto contiene piezas pequeñas que, si fuesen tragadas, podrían producir asfixia.
Antes de iniciar el ensamblaje, compruebe que todas las piezas estén incluidas y en buenas condiciones. Si faltan piezas o alguna está dañada, no devuelva el artículo al distribuidor; póngase en contacto con el Servicio de Atención al Cliente.
Nunca utilice piezas deterioradas.
NOTA: No todos los accesorios incluidos deberán utilizarse.
ESPAÑOL
PASO 1
Instalar los brazos de la placa de sujeción a la barra de sonido (Opción 1)
Verifique la compatibilidad de la placa de sujeción para barra de sonido con su barra de sonido.
Ensamble las perillas
04
y tornillos
03
.
Acople los brazos de la barra de sonido
01
a la barra de sonido. No ajuste completamente las perillas
04
.
NOTA:
Al planificar la ubicación de la barra de sonido, asegúrese de que podrá acceder a los botones de los controles.
PASO 1
Instalar los brazos de la placa de sujeción a la barra de sonido (Opción 2)
Verifique la compatibilidad de la placa de sujeción para barra de sonido con su barra de sonido.
Ensamble las perillas
04
y tornillos
03
.
Algunas conexiones de la barra de sonido pueden requerir una arandela en “C” asegurar que los brazos de la barra de sonido
02
para
01
permanezcan horizontales sobre la barra de sonido. Si es necesario, introduzca una arandela en “C” las perillas
02
sobre los tornillos de
03
y debajo de los brazos
01
y luego ajuste levemente las perillas
04
.
31
ESPAÑOL
PASO 1
Instalar los brazos de la placa de sujeción al soporte (Opción 3)
Algunas barras de sonido vienen con un soporte proporcionado por el fabricante.
Acople los brazos de la barra de sonido
01
al soporte de la misma con las perillas
04
y los tornillos
03
.
No ajuste completamente las perillas
04
.
PASO 2
Preparar el televisor
Si su televisor ya está instalado en un soporte:
A.
Retire todos los cables conectados al televisor.
B.
Retire el módulo televisor-placas de la placa mural, del brazo o del soporte vertical.
Consulte el manual de instalación de la placa mural del televisor para ver las instrucciones.
¡ELEMENTO PESADO! Es posible que necesite ayuda en este paso.
C.
Retire la placa de sujeción del televisor.
IMPORTANTE
! Consulte el manual de la placa mural del televisor para ver las instrucciones sobre cómo retirar el soporte de conexión del televisor.
32
ESPAÑOL
! Guarde los elementos de sujeción del televisor en caso de desear utilizar en el futuro el televisor
sin la barra de sonido.
! Debe utilizar los elementos de sujeción proporcionados con este producto en lugar de aquellos que vinieron con el soporte.
PASO 3
Instale la placa de sujeción del televisor con el módulo televisor-placas
Determine el diámetro de los pernos para su monitor y su tipo de televisor: M4, M5, M6, o M8.
• Para televisores con dorso plano/libre de obstrucciones, consulte el Paso 3-1
• Para televisores con dorso irregular/con obstrucciones, consulte el Paso 3-2
Si necesita más espacio para cables, concavidades o protuberancias, consulte el Paso 3-2 que utiliza separadores.
Se ilustran las configuraciones estándar. En caso de aplicaciones especiales, comuníquese con el Servicio de Atención al Cliente.
PRECAUCIÓN:
Utilice la combinación más corta de tornillo y separador para cables, concavidades o protuberancias. Utilizar tornillos demasiado largos puede dañar los componentes
internos del monitor.
33
ESPAÑOL
PASO 3-1 PASO 3-2
ADVERTENCIA:
Debe usar las arandelas más grandes
09
o
10
, a menos que no sean adecuadas para el soporte del televisor.
NOTA:
La barra de sonido debe colocarse debajo del televisor, tal como se muestra.
PRECAUCIÓN:
Los extremos de los brazos del televisor/placa de sujeción
05
no deben sobrepasar el borde del televisor.
PASO 4
Acople el módulo de la barra de sonido al televisor
Fije el módulo barra de sonido/brazo usando perillas
01
a los brazos del televisor/placa de sujeción
05
04
. No ajuste completamente las conexiones.
NOTA:
Es posible que deba usar el método de ensayo y error para lograr la configuración correcta del conjunto barra de sonido/placas de sujeción del televisor.
34
ESPAÑOL
PASO 5
Ajuste los brazos
Acomode los brazos de la barra de sonido/placa de sujeción placa de sujeción
01
y los brazos del televisor/
05
hasta que la barra de sonido o el soporte de la misma se encuentre en la posición deseada.
NOTA:
La barra de sonido debe colocarse a una distancia máxima de 51 mm (2'') del televisor.
PASO 6
Ajuste las conexiones
Cuando la barra de sonido o su soporte se encuentre en la posición deseada, ajuste todas las conexiones.
PASO 7
Colgar el módulo
Siga las instrucciones del manual de instalación de la placa mural del televisor para volver a colgar el módulo.
35
Customer Service
Americas: 888-333-9952 • [email protected]
UK: 0800-056-2853
SANUS • 6436 City West Parkway • Eden Prairie, MN 55344 USA
36
©2013 Milestone AV Technologies, a Duchossois Group Company. All rights reserved.
Sanus is a division of Milestone.
All other brand names or marks are used for identifi cation purposes and are trademarks of their respective owners.
6902-002055 00
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project