Technical Data

VCXG-22M.R

Digital Monochrome Matrix Camera, 2.1 Megapixel, GigE

Article No. 11209586

Firmware Revision 3.0

Sensor Graph: Relative Response

Frame Rates / Partial Scan

(Measured at Mono8/BayerRG8-Format)

Digital Output: High Active

Sensor Information

Model Name

Type

Shutter

Resolution

Scan Area

Pixel Size

Sony IMX290

1/2.8″ progressive scan CMOS

Rolling Shutter, Global Reset Shutter

1920 × 1080 pixels

5.56 mm x 3.13 mm

2.9 µm x 2.9 µm

Data Quality

Dark Noise (



)

Saturation

Dynamic Range

SNR

Quantum efficiency η

Acquisition

Resolution

Interface Frame Rate

(depends on used interface performance)

@ 20 °C, gain = 1, exposure time = 4 msec

3 e- typical

14000 e- typical

71 dB typical

41 dB typical

83 % @ 536 nm typical

Acquisition Frame Rate 1)

(Burst Mode)

1920 px x 1080 px

Format Resolution max. Frame Rate

(@ Trigger Mode) 2)

Full Frame

Binning 2x2

Binning 2x1

1920

960

960 x x x

1080

540

1080

58 fps

89 fps

58 fps

Binning 1x2 1920 x 540 89 fps

89 fps | t readout

= 11.2 msec

(max. Res. Full Frame) @ 10 bit

60 fps | t readout

= 16.7 msec

(max. Res. Full Frame) @ 12 bit

Mono8, Mono10, Mono12, Mono12p Pixel Formats

Partial Scan

True Partial Scan with increasing Frame Rate on Y direction, Region of Interest (ROI) arbitrary

Width: minimum 32, increment 32

Heigth: minimum 2, increment 2

Off or

Off or 0.39 … 65535 Hz

Adjustable Acquisition

Frame Rate

Acquisition Mode

Acquisition Status

Exposure Mode

Readout Mode

Continuous, Single Frame and Multi Frame

AcquisitionActive, AcquisitionTrigger Wait

Timed not available

Image Pre-Processing

Analog Controls

Auto Function

Exposure Time (15 µsec … 60 sec | Step Size 1 µsec)

Gain ( 0…48 dB), Offset (0 ... 255 LSB | 12 bit)

ExposureAuto and GainAuto with BrightnessAutoPriority based on BrightnessAuto ROI

LUT

Color Models

Color Processing

Color Adjustment

Color Enhancement

Color Tolerance

-

-

-

-

Luminance (12 bit)

Mono

1) Sensor readout, different from pixel format

2)

depends on the used interface

2)

depends on the used interface

TDS_VCXG-22M.R

02.06.2020

1

The Information in this document is subject to change without notice.

Baumer Optronic GmbH

Radeberg, Germany

Digital Output: Low Active

Digital Input

Trigger Mode: Start up time and valid Trigger

Image Pre-Processing

Binning Horizontal

Binning Vertical

Image Flipping

Defect Pixel Correction

Fix Pattern Noise

Correction

1 or 2

1 or 2 no via Defect Pixel List with up to 512 Pixel Coordinates

-

Process Synchronization

Trigger Mode

Trigger Overlap Type

Trigger Sources

Trigger Delay

External Flash Sync

Encoder Function

PTP Function

Off (Free Running), On (Trigger)

Trigger Mode On: Off

Trigger Mode Off: Not available

Hardware (Line0, 1, 2), Software, Counter 1, 2 End, Action

CMD (Action 1), All or Off max. Trigger Delay out of t readout

:

1)

11124 µsec / 10 µsec @ 10 bit (Rolling / Global Reset)

16603 µsec / 14.9 µsec @ 12 bit (Rolling / Global Reset) max. Trigger Delay during t readout

: 1)

-

-

-

0 ... 2 sec, Tracking and buffering of up to 256 triggers via Exposure Active t delay flash

≤ 3 µsec, t duration

=t exposure

Digital I/Os

Lines

Output Sources

Line Debouncer

Input: Line 0, Output: Line3, GPIO: Line 1, Line 2

Off, ExposureActive, Timer1, ReadoutActive,

UserOutput 1-3 and TriggerReady

Low and high signal separately selectable

Debouncing Time 0 … 5 msec, Step Size: 1 μsec

GPIO IN

GPIO

Memory

Image Buffer

Non-volatile Memory

95 MB

16 Images (Trigger Mode) / 1 Image (Free Running Mode)

128 kb

Network Interface Data

Interface Gigabit Ethernet 1000BASE-T 1000 Mbits/sec

Fast Ethernet 100 BASE-T 100 Mbits/sec

Ethernet IP Configuration Persistent IP, DHCP, LLA

Packet Size 576 … 9000 Byte, Jumbo Frames supported

GigE Vision

®

Features

Events DeviceTemperatureStatusChanged, EventLost,

Transmission via Asynchronous

Message Channel

ExposureEnd, ExposureStart, FrameEnd, FrameStart,

FrameTransferSkipped, GigEVisionError,

Action CMD

Frame Counter

Payload Size

Timestamp

Packet Delay

Packet Resend

GigE Vision

GigEVisionHeartbeatTimeOut, PrimaryApplicationSwitch,

Line0..2 FallingEdge, Line0..2 RisingEdge,

TransferBufferFull, TransferBufferReady,

TriggerOverlapped, TriggerReady, TriggerSkipped yes, Action 1 for Trigger up to 2 32

0 … 4147412 Byte

64 bit, resolution in nsec, increment = 8

0 .. 2

32 – 1 nsec

Resend Buffer: 64 MB (16 Images) v2.0 (v1.2 backward compatible)

1)

GPIO OUT High Active

Sensor readout, different from pixel format

TDS_VCXG-22M.R

02.06.2020

2

The Information in this document is subject to change without notice.

Baumer Optronic GmbH

Radeberg, Germany

Pin Assignment Data Interface

Pin Assignment Process Interface

(on camera side)

5

7

6 4

3

1 2

8 wire colors on connecting cables

(ordered separately)

1 White

2 Brown

3 Green

4 Yellow

5 Grey

6 Pink

7 Blue

8 Red

Device Temperature: T = Measurement Point

Interfaces and Connectors

Data and Power Interface Gigabit Ethernet Transfer Rate 1000 Mbits/sec

Fast Ethernet Transfer Rate 100 Mbits/sec

Connector:

8P8C Modular Jack (RJ45),

screw lock type

Assignment: 1 - MX1+ 2 - MX1-

3 - MX2+

5 - MX3-

7 - MX4+

4 - MX3+

6 - MX2-

8 - MX4-

Process Interface

Caution

Connector: M8/8-pin

(SACC-DSI-M8MS-8CON-M8-L180)

Assignment: 1 - GPIO (Line2) 2 - Power Vcc

3 - IN1 (Line0)

5 - Power VCC OUT

7 - GND (Power, GPIO)

4 - GND IN1

6 - OUT1 (Line3)

8 - GPIO (Line1)

* Note GPIOs: Ground loops are to be avoided and can lead to destruction of the device.

Optical Data

Lens Mount

Optical Filter

Mechanical Data

Housing

Protection Class

Weight

Dimensions

C-Mount

-

Zinc die casting, baked varnish

(until 02-2020 nickel-chrome-plated)

IP40 (with mounted lens and GigE cable)

120 g

LED Signalling

TDS_VCXG-22M.R

02.06.2020

Environmental Data

Storage Temperature

Operating Temperature

*)

-

10 °C … + 70 °C

+5 °C … +65 °C @ T = Measurement Point or

+5 °C … +72 °C @ internal Temperature Sensor

Ambient temperature above 37 °C requires heat dissipation measures.

Int. Temperature yes, accuracy:

Sensor

Humidity

±1 °C (typ) 0 °C ... +85 °C

10 % … 90 % non-condensing

*)

the maximum temperature for Sony sensor characteristics (sensor performance) are guaranteed up to 54°C @

Measurement Point or 60°C @ internal temperature sensor

LED Signalling

LED LED 1

LED 2

Green static

Green flash

Yellow static

Yellow flash

Link ON

RX active

Error

TX active

3

The Information in this document is subject to change without notice.

Baumer Optronic GmbH

Radeberg, Germany

Electrical Data

Power Supply (ext.)

Power over Ethernet

Power Consumption

Digital Input

Digital Output

GPIO

GPIO used as Input:

GPIO used as Output:

Caution

VCC: 12 … 24 V DC ± 20%

I: 79 … 159 mA

Class 1 device

VCC: 36 … 57 V DC

I: 50 mA @ 48 VDC approx. 1.9 W @ 12VDC and 58 fps approx. 2.4 W @ 48 VDC (PoE) and 58 fps

(Factory Setting “Default”)

Optocoupler

U

IN(low)

:

0.0 … 4.5 VDC

U

IN(high)

: 11.0 … 30.0 VDC

I

IN

: 3.0 … 10.0 mA min. Impulse Length: 2.0 μsec

Optocoupler

U

EXT

: 5 … 30 V DC

I

OUT

: max. 50 mA t

ON

= typ. 3 µsec t

OFF

= typ. 40 µsec direct, without optocoupler

U

IN(low)

: 0.0 … 0.8 VDC

U

IN(high)

: 2.0 … 30.0 VDC min. Impulse Length: 2.0 μsec

U

Out(low)

: 0.0 … 0.4 VDC (I sink max

: 50 mA)

U

Out(high)

: 2.4 … 3.3VDC (I max

: 1 mA)

* The General Purpose I/Os (GPIOs) are not potential-free and do not have an overrun cut-off. Incorrect wiring (overvoltage, undervoltage or voltage reversal) can lead to defects in the electronic system.

Ground loops are to be avoided and can lead to destruction of the device.

Conformity

Conformity CE, RoHS, REACH

KC Registration No. / Date - / -

MTBF 60 years @ T = 45 °C / 39 years @ T = 60 °C

T = Measurement Point

GenICam™ Features

Short Exposure Range

Timer

Counter

Sequencer

-

Timer Selector: Timer 1

TimerTriggerSource:

Line0, SoftwareTrigger, ExposureStart, ExposureEnd,

FrameTransferSkipped, TriggerSkipped, Action 1 and Off

TimerDelay: 0 μsec … 2 sec, Step Size: 1 μsec

TimerDuration:

4 μsec … 2 sec, Step Size: 1 μsec

Counter Selector: Counter 1, Counter 2

CounterValue: 0 … 65535

Counter Event Source: Counter1End or Counter2End,

ExposureActive, FrameTransferSkipped, FrameTrigger,

TriggerSkipped, Line0..2 and Off

Counter Reset Source: Counter1End, Counter2End,

Line0..2 and Off no

TDS_VCXG-22M.R

02.06.2020

4

The Information in this document is subject to change without notice.

Baumer Optronic GmbH

Radeberg, Germany

TDS_VCXG-22M.R

02.06.2020

GenICam

TM

Features

User Sets

Acquisition Abort

Chunk Data

Device Temperature

Factory Settings: UserSet0 (read only)

Freely Programmable: UserSet1, UserSet2, UserSet3

Parameters: any user definable Parameter

Delay up to 16.7 msec yes,

Chunk Selector: Binning, BlackLevel, CounterValue,

DeviceTemperature, ExposureTime, FrameID, Gain,

Height, Image, ImageControl, LineStatusAll,OffsetX,

OffsetY, PixelFormat, , Timestamp, Width

InHouse

Event generation for Normal to High, High to Exceeded and Exceeded to Normal

Exceeded (no image transfer) = max. internal temperature sensor + 1 °C yes, up to max. Device Link Speed Device Link Throughput

Limit

Custom Data

SFNC Version yes, 128 Byte v2.4

Factory Settings after Start-Up

Ethernet IP Configuration

Trigger Mode Off (Free Running)

Analog Controls

Pixel Format

Exposure Time: 4 msec, Gain: 0 dB, Offset: 0

Mono8

Partial Scan Off

Acquisition Frame Rate Off

Timer/Counter/Sequencer Off

Defect Pixel Correction ON

- Fixed Pattern Noise

Correction

Digital Input

Digital Output

GPIO 1/2

TriggerSource

Line0, invert = false

Line3, invert = false, line source = Off

Line1, Line2, invert = false, LineMode = Input

All

Partial Scan

@ FullFrame, min Exposure, Mono8 (monochrome camera) or BayerRG8 (color camera)

Full HD

SXGA

HD720

XGA

SVGA

VGA

CIF

QVGA

QCIF

LineScan

Resolution

1920 x 1080

1280 x 1024

1280 x 720

1024 x 768

800 x 600

640 x 480

352 x 288

320 x 240

176 x 144

1920 x 1024

1920 x 512

1920 x 256

1920 x 128

1920 x 64

1920 x 32

1920 x 16

1920 x 8

1920 x 4

1920 x 2

1920 x 1

2) depends on the used interface max. fps acquisition

234,9

296,9

296,9

296,9

296,9

297,0

296,9

297,0

-

58,5

91,8

129,7

124,7

157,5

194,4

296,9

297,0

-

61,7

121,3 max. fps interface 2)

234,9

296,9

296,9

296,9

296,9

297,0

296,9

297,0

-

58,5

91,8

129,7

124,7

157,5

194,4

296,9

297,0

-

61,7

121,3

5

The Information in this document is subject to change without notice.

Baumer Optronic GmbH

Radeberg, Germany