- Computers & electronics
- Telecom & navigation
- Mobile phones
- Car kits
- Metra
- 95-9315B
- Installation Guide
Metra 95-9315B Car Kit Installation Guide
Add to My manuals4 Pages
Metra 95-9315B is a car installation kit designed to provide a seamless and secure mounting solution for ISO DDIN radios in BMW 1 Series vehicles manufactured between 2008 and 2013, specifically those without factory navigation and equipped with automatic climate control.
advertisement
95-9315B
I N S TA L L AT I O N I N S T R U C T I O N S
BMW
1 Series
(without NAV, with automatic climate control)
2008-2013
KIT FEATURES
• ISO DDIN radio provision
• Painted to match the factory finish
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Preparation ....................................................2-3
Kit Assembly ..........................................................3
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: LC-BMRC-01 (non-amplified models)
Antenna Adapter: 40-EU10
KIT COMPONENTS
• A) Radio housing • B) Radio brackets • C) Switch panel cover • D) Ribbon cable
A B C D
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• Cutting tool
Metra. The World’s Best Kits.
® MetraOnline.com
© COPYRIGHT 2018 METRA ELECTRONICS CORPORATION
CAUTION! All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running.
REV. 2/14/18 INST95-9315B
DASH DISASSEMBLY
1.
Unclip and remove the dash trim panel above the radio and glove box.
2.
Unclip the climate control panel, then unplug and remove.
3.
Unclip the switch panel below the climate control panel (if equipped), then unplug and remove.
4.
Unclip and remove the climate controls from the climate control panel.
5.
Remove (2) screws securing the bottom of the radio, then unplug and remove the radio.
Continue to Kit Preparation
Please visit Metraonline.com for
Dash Disassembly illustrations.
KIT PREPARATION
1.
Using a cutting tool, remove the sections of sub-dash indicated to provide clearance for the radio and climate controls. (Figure A)
Note: There may be other obstructions from allowing the radio to slide into the dash depending on the size of the radio. Carefully cut as needed, making sure not to cut anything structural.
For models with a switch panel below the climate control.
2.
Remove (5) screws securing the switch panel back plate, then remove the switch panel circuit board.
3.
Unplug the ribbon cable from the circuit board. (Figure B)
Continued on the next page
(Figure A)
Remove shaded areas
(Figure B)
2 1.800.221.0932 | MetraOnline.com
KIT PREPARATION
(CONT.)
4.
Attach the White connector from the ribbon cable supplied with the kit to the circuit board.
5.
Reinstall the circuit board back into the switch panel.
6.
Clip the climate control panel, and switch panel, into the radio housing.
(Figure C)
7.
Attach the Black connector from the ribbon cable to the climate control panel. (Figure D)
(Figure C)
For models without a switch panel below the climate control.
8.
Clip the switch panel cover to the radio trim panel.
9.
Disregard the ribbon cable, it will not be used in this application.
Continue to Kit Assembly
(Figure D)
KIT ASSEMBLY
ISO DDIN radio provision
1.
Attach the radio brackets to the radio using the screws supplied with the radio. (Figure A)
2.
Locate the factory wiring harness and connector in the dash and complete all necessary connections to the radio.
Metra recommends using the proper mating adapter from Metra and/or
Axxess. Test the radio for proper operation.
3.
Secure the completed assembly into the dash with the facory screws.
4.
Reassemble the dash in reverse order of disassembly using radio trim panel assembly to complete the installation.
(Figure A)
REV. 2/14/2018 INST95-9315B 3
95-9315B
I N S TA L L AT I O N I N S T R U C T I O N S
IMPORTANT
If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.
Metra. The World’s Best Kits.
® MetraOnline.com
© COPYRIGHT 2018 METRA ELECTRONICS CORPORATION
® K NOWLEDGE IS P OWER
E nhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps toward a better tomorrow.
Metra recommends MECP certified technicians
REV. 2/14/18 INST95-9315B
advertisement
Related manuals
advertisement