IMPORTANT:

RETAIN FOR FUTURE REFERENCE

READ CAREFULLY

BATH VANITY WITH HEATER

INSTRUCTION MANUAL

MODEL # 15II500ARA

Questions, problems, missing parts?

Twin-Star International, Inc.

Delray Beach, FL 33445

Made in China

Printed in China

©2012, Twin-Star International, Inc.

V020917

1

For Customer Service: www.twinstarhome.com

866-661-1218

8:30 a.m. - 5:30 p.m., EST, Monday-Friday

IMPORTANT INSTRUCTIONS

Please read and understand this entire manual before attempting to assemble, operate or install the product. If you have any questions regarding the product or assembly, please call customer service at 1-866-661-1218, 8:30 a.m.-5:30 p.m., EST, Monday-Friday.

When using electrical appliances always follow basic precautions to reduce the risk of shock, and injury to persons including the following:

1. Read all instructions before using this appliance.

2. This appliance is hot when in use. To avoid burns do not touch hot surfaces with bare skin.

Keep combustible materials such as furniture, pillows, bedding, papers, clothes and curtains at least 3 ft / 0.9 m from the front of this appliance.

WARNING: Use extreme caution when operating heater near children and the invalid.

3. The appliance is not to be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given instruction or are

4. This appliance is not a toy. Supervise children when they are close to heater.

5. If possible, always unplug this appliance when not in use.

6. Do not operate any heater with a damaged cord or plug, after the appliance malfunctions, or if it has been dropped or damaged in any manner.

7. If the supply cord is damaged it must be replaced by the manufacturer, it’s service agent or similarly

!

must be replaced prior to operating this heater again.

10. Do not use outdoors.

11. Do not run cord under carpeting. Do not cover cord with throw rugs, runners or the like. Arrange cord

"! !" "

12. To disconnect this appliance turn controls to the off position and then remove plug from outlet.

13. Connect to properly grounded outlets only.

14. This appliance must be electrically grounded in accordance with local codes or, in the absence of local codes, with the current CSA C22.1 Canadian Electrical Code or for U.S.A. installations, follow local codes and the National Electrical Code, ANSI/NFPA NO.70.

15. The heater must not be located immediately below a socket-outlet.

16. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause

$

%&' $ $( ) ! surfaces, like a bed, where opening may become blocked.

18. This appliance has hot and arcing or sparking parts inside. Do not use in areas where gasoline,

* ' $!

clothing. Do not hang Christmas stockings or other decorations on or near this product.

19. Use this appliance only as described in the manual. Any other use not recommended by the

! $+

20. There is a thermostat limiter inside the heater. When inner temperature is overheating or abnormal

heating occurs the thermostat protective device will cut off the power supply to avoid damage to the

$!

2

IMPORTANT INSTRUCTIONS

21. Always plug heater directly into a wall outlet/receptacle. Never use with an extension cord or

relocatable power tap (outlet/power strip).

22. Reference Fig. 1 for grounding instructions. This heater is for use on 120 volts. The cord has a plug as shown in Fig. 1A. An adapter as shown in Fig.1C is available for connecting three-blade grounding type plugs to two-slot receptacles. The grounding pin extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available.

Grounding Pin

Adapter

Grounding

Means

Cover Of Grounded

Outlet Box

Metal

Screws

A B

C D

Grounding

Pin

Fig. 1

SAVE THESE

INSTRUCTIONS

For product warranty registration please visit:

www.twinstarhome.com/registration

Before setting up this product please record the model number and serial number of this product in the spaces below for registration and warranty reference.

Heater Model Number Serial Number

3

PACKAGE CONTENTS

Fig. 2

Remote Control

A

C

Touch-up Pen

Bath Vanity with Heater

D

E

Counter-top Remote Stand

Part

A

B

C

D

E

HARDWARE CONTENTS

AA

Screw

0.2 in. x 1.5 in.

Description

Bath Vanity with Heater

Remote Control

Touch-up Pen

Counter-top Remote Stand

Wall Mounted Remote Holder

Wall Mounted Remote Holder

Quantity

1

1

1

1

1 x 3

4

B

HEATER LOCATION

HEATER PLUG & MAIN POWER SWITCH

When choosing a location for your new heater be sure that the general instructions are followed.

Also, for best effect, install the heater out of direct sunlight.

ELECTRICAL CONNECTION

=%>=?%@JQ XJY " grounded outlet is required. Preferably, the heater will be on a dedicated circuit as other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow when the heater is in operation. The unit comes standard with 6 feet

(1.8 m) three wire cord, exiting from the rear of the heater.

CAUTION : Do not exceed the current rating of the current tap. Always plug heaters directly into a wall outlet/ receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).

ELECTICAL SPECIFICATIONS (15II500ARA)

The heater is equipped with a ground fault circuit indicator plug. Plug the heater directly into a standard 120V outlet; the light will indicate correct function.

1. Press the TEST button,if the indicator light goes

out function is correct.

2. Press the RESET button, if the indicator

becomes re-lit function is normal.

3. The Heater has a main power switch on the

back of the heater enclosure. Ensure that the

main power switch is in on the ON position as

shown in Fig. 4.

RESET

TEST

Voltage

Amps

Watts

%@JQZXJY

12.5 Amps

1500 Watts

INDICATOR

LIGHT

CLEARANCE TO COMBUSTIBLES

Keep electrical cords, drapery, furniture and other combustibles at least 3 feet (0.9 m) from the front and sides of the heater.

CLEANING TRIM

Clean the trim using a soft cloth, slightly dampened with citrus oil based product and buff with a clean soft cloth. DO NOT use brass polish or household cleaners as these products will damage the metal trim. Citrus oil based products can be obtained at supermarkets or hardware stores.

Fig. 3

Main Power

Switch Fig. 4

5

Remote Control Installation

5.2

D

5.1

5.3

6.2

Fig. 5

E

6.1

6.3

Fig. 6

6

Heater Functions:

To Turn On or Off the Heater:

Press the HEATER button which will turn on or off the heater regardless

of the programed settings.

To Adjust the Thermostat:

Press the the THERMOSTAT button; the temperature display will start

* )\] '

theremostat adjustable range is 50°F to 97°F (10°C - 36°C.)

To Change Between °F and °C:

Press and hold the HEATER button for 4 seconds.

Setting the Time and Date:

To Set the Time:

'^?_ " * ""

to adjust the hours, press enter to adjust the minutes next then press enter to select AM or PM.

To Set the Date:

)='_ ! "$" *

down buttons to select the day of the week then press enter.

Setting the Program:

Weekday or Weekend Program:

the heater has two programs that can be individually set:

`\$z?{|

`\$z} }

To Set the Program:

press WEEKDAY or WEEKEND on the control panel to set either program.

`' " " * 

then press ENTER on the remote control.

`]( "* ! }

press enter.

For example if the Weekday starting time was set at 8:00am and the run length at 2:00 then the

heater will run Monday - Friday 8:00am - 10:00am.

`\ " +

the desired temperature.

7

REPLACING THE REMOTE CONTROL BATTERIES

When the remote control stops operating, or it’s range seems reduced, it is time to replace the batteries. To extend the life of the batteries remove the batteries if the remote control won’t be used for a long period of time.

1. The battery compartment is located on the back end of the remote.

2. Press the small tab inward as you slide the battery door open and remove the old batteries.

3. Insert (2) AAA batteries, making sure the + and - sides of the battery match the inside of the battery

compartment.

4. Replace the battery door.

CAUTION:

`=" ! !

` !

`‚ !

`_ " …†{‡

` ! " !( !

`

Note: Do not mix old and new batteries.

) ($ …‡… ‡

Caution: Do not ingest batteries.

If batteries have been swallowed, contact the municipal poison control center.

DISPOSAL OF USED BATTERIES

€ "

Batteries shall not be treated as municipal waste. Batteries should be disposed of at an appropriate collection point for recycling.

By ensuring the used batteries are disposed of correctly, you will help prevent potential negative consequences for the environment and human health. The recycling of materials will help to conserve natural resources.

For more information about recycling of used batteries please contact your local municipality waste disposal service.

NOTE : This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. Interference can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by trying one or more of the following measures:

` 

` ^ "

` ‚ !! ! "

` ‚ (ƒ'Q !

FCC STATEMENT

1.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference and

(2) This device must accept any interference received, including interference that may cause undesired

operation

2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

8

TROUBLESHOOTING GUIDE

PROBLEM

1. Heater does not blow warm air.

SOLUTION

1a. The ambient temperature is higher than the thermostat

setting.

1b. Unplug the unit from the wall outlet for 2 hours. After 2

hours plug the unit back into wall outlet, and operate as

normal.

1c. Check if the air inlet is blocked.

@ ˆ"*" 2a. Check if the air inlet is blocked.

3. The heater does not run in the

program.

3a. Check that the thermostat is higher than the room

temperature.

4. The heater is not responding to

signals from the remote control.

5. The heater does not work.

4a. The remote and heater body may have become unpaired.

To re-pair the remote and heater press and hold the

HEATER and ENTER buttons simultaneously. The heater

body will emit a long beep to indicate pairing was

successful.

4b. See display to judge if no power of battery.

4c. Remote can be opeate the unit within 7 m. Need to see if

there have a long distance between remote control and

hetaer body.

5a. Check the main power switch on the back of heater if it is

in the ON position;

5b. The indicator light on the power cord not lit. Press the

RESET button, if the indicator becomes re-lit function is

normal.

WARNING: Make sure the power is turned off before proceeding. Any electrical repairs or rewiring of this unit should be carried out by a licensed electrician in accordance with national and local codes.

If repairing or replacing any electrical component or wiring, the original wire routing, color coding and securing locations must be followed.

WARNING: Electrical outlet wiring must comply with local building codes and other

$! $+

WARNING: Do not use this heater if any part of it has been under water. Immediately

! electrical system.

Warning: Disconnect power before attempting any maintenance or cleaning to reduce the

$! $+

Warning: During any service of this appliance, the power to the unit must be turned off.

First turn the main power switch to the “OFF” position. Then remove the electrical plug from the wall outlet.

9

1-YEAR LIMITED WARRANTY

The manufacturer warrants that your new vanity heater is free from manufacturing and material defects for a period of one year from date of purchase, subject to the following conditions and limitations.

1. Install and operate this electric heater in accordance with the installation and operating

!" = "!

accident, or misuse of the product shall nullify this warranty.

2. This warranty is non-transferable and is made to the original owner, provided that the purchase was

!

3. The warranty is limited to the repair or replacement of part(s) found to be defective in material or workmanship, provided that such part(s) have been subjected to normal conditions of use and

! ! ! ‰

4. The manufacturer may, at it’s discretion, fully discharge all obligations with respect to this warranty by refunding the wholesale price of the defective part(s).

5. Any installation, labor, construction, transportation, or other related costs/expenses arising from defective part(s), repair, replacement, or otherwise of same, will not be covered by this warranty, nor shall the manufacturer assume responsibility for same.

6. The owner/user assumes all other risks, if any, including the risk of any direct, indirect or consequential loss or damage arising out of the use, or inability to use the product, except as provided by law.

7. All other warranties – expressed or implied –with respect to the product, it’s components and accessories, or any obligations/liabilities on the part of the manufacturer are hereby

'! ‰!

any other liabilities with respect to the sale of the product.

9. The warranties as outlined within this document do not apply to non accessories used

in conjunction with the installation of this product.

%J'" "

from state to state.

This warranty is void if: a. The heater is subjected to prolonged periods of dampness or condensation.

' "! ! c. You do not have the original receipt of purchase.

IF WARRANTY SERVICE IS NEEDED

Contact the manufacturer at www.twinstarhome.com or call our customer service department at 1-866-661-1218, 8:30 a.m.-5:30 p.m., EST, Monday-Friday. Make sure you have your warranty, your sales receipt, location of purchase and the model/serial number of your product.

10