Aiwa NSX-SZ900 Service Manual

All manuals and user guides at all-guides.com

NSX-SZ900

LH

SERVICE MANUAL

COMPACT DISC

STEREO SYSTEM

BASIC TAPE MECHANISM : 2ZM-3MK2 PR7NM

BASIC CD MECHANISM : BZG-5 ZD3N1DM

SYSTEM SPEAKER

CD

CASSEIVER

REMOTE

CONTROLLER

SX-WNSZ900

NSX-SZ900 CX-NSZ900 RC-BAS04

SX-S85

all-guides.com

• This Service Manual is the “Revision Publishing” and replaces “Simple Manual”

of CX-NSZ900 (LH), (S/M Code No. 09-013-444-1T1).

• If requiring information about the CD mechanism, see Service Manual of BZG-5,

(S/M Code No. 09-00C-353-3N2).

S/M Code No. 09-015-444-1R1

REVISION

DA

TA


SPECIFICATIONS

<FM tuner section>

Tuning range

Usable sensitivity (IHF)

Antenna terminals

<AM Tuner section>

Tuning range

87.5 MHz to 108 MHz

13.2 dBf

75 ohms (unbalanced)

Usable sensitivity

Antenna

530 kHz to 1710 kHz (10 kHz step)

531 kHz to 1602 kHz (9 kHz step)

350

µ

V/m

Loop antenna

<Amplifier section>

Main amplifier

Power output Rated: 172 W + 172 W

(6 ohms, T.H.D. 1 %, 1 kHz )

Reference: 215 W + 215 W

(6 ohms, T.H.D. 10 %, 1 kHz )

Total harmonic distortion 0.1 % (150 W, 1 kHz, 6 ohms,

DIN AUDIO)

Satellite amplifier

Power output Rated: 20 W + 20 W

(8 ohms, T.H.D. 1 %, 1 kHz )

Reference: 25 W + 25 W

(8 ohms, T.H.D. 10 %, 1 kHz )

Total harmonic distortion 0.2 % (8 W, 1 kHz, 8 ohms,

DIN AUDIO)

Inputs VIDEO/AUX: 300 mV (adjustable)

MD: 300 mV (adjustable)

MIC 1, MIC 2: 1.0 mV (10 kohms)

Outputs SPEAKERS: 6 ohms or more

SATELLITE SPEAKERS:

8 ohms or more

LINE OUT: 210 mV

CD DIGITAL OUT (OPTICAL)

PHONES: 32 ohms or more

<Cassette deck section>

Track format

Frequency response

Recording system

Heads

4 tracks, 2 channels stereo

CrO

2

tape: 50 Hz – 16 kHz

Normal tape: 50 Hz – 15 kHz

AC bias

Deck 1: Playback x 1

Deck 2: Recording/playback x 1, erase x 1

<CD player section>

Laser

D-A converter

Signal-to-noise ratio

Harmonic distortion

<General>

Power requirements

Power consumption

Power consumption in standby mode

Dimensions (W x H x D)

Weight

Semiconductor laser (

1 bit dual

85 dB (1 kHz, 0 dB)

0.05 % (1 kHz, 0 dB)

λ

= 780 nm)

120 V/ 220 V – 230 V/ 240 V AC

(switchable) 50/60 Hz

250 W

With ECO mode on: 0.6 W

With ECO mode off: 40 W

260 x 326 x 394 mm

10.5 kg

<Main speakers SX-WNSZ900>

Speaker system 3 way, Built-in subwoofer

Speaker units

(magnetic shielded type)

Subwoofer: 200 mm cone type

Impedance

Full range: 100 mm cone type

Super tweeter: 20 mm ceramic type x 2

6 ohms


Weight

240 x 324 x 294 mm

5.4 kg

<Satellite speakers SX-S85>

Speaker system

Speaker units

Impedance

Sensitivity


Weight

Full range (magnetic shielded type)

80 mm cone type

8 ohms

87 dB/W/m

100 x 325 x 95 mm (with pedestal)

100 x 186 x 84 mm (without pedestal)

0.6 kg

• Design and specifications are subject to change without

notice.

• The word “BBE” and the “BBE symbol” are trademarks of BBE

Sound, Inc.

Under license from BBE Sound, Inc.

– 2 –


PROTECTION OF EYES FROM LASER BEAM DURING SERVICING

This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing.

WARNING!!

WHEN SERVICING, DO NOT APPROACH THE LASER

EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS

NECESSARY TO CONFIRM LASER BEAM EMISSION.

BE SURE TO OBSERVE FROM A DISTANCE OF MORE

THAN 30cm FROM THE SURFACE OF THE OBJEC-

TIVE LENS ON THE OPTICAL PICK-UP BLOCK.

s Caution: Invisible laser radiation when open and interlocks defeated avoid exposure to beam.

s Advarsel: Usynlig laserståling ved åbning, når sikkerhedsafbrydere er ude af funktion.

Undgå udsættelse for stråling.

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herin may result in hazardous radiation exposure.

ATTENTION

L’utillisation de commandes, réglages ou procédures autres que ceux spécifiés peut entraîner une dangereuse exposition aux radiations.

ADVARSEL

Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude af funktion. Undgå udsættelse for stråling.

This Compact Disc player is classified as a CLASS 1

LASER product.

The CLASS 1 LASER PRODUCT label is located on the rear exterior.

VAROITUS!

Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saataa altistaa käyt-täjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.

VARNING!

Om apparaten används på annat sätt än vad som specificeras i denna bruksanvising, kan användaren utsättas för osynling laserstrålning, som överskrider gränsen för laserklass 1.

CLASS 1 LASER PRODUCT

KLASSE 1 LASER PRODUKT

LUOKAN 1 LASER LAITE

KLASS 1 LASER APPARAT

Precaution to replace Optical block

(KSS-213F)

Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode.

1) After the connection, remove solder shown in right figure.

PICK-UP Assy PWB

Solder

– 3 –


NOTE ON BEFORE STARTING REPAIR

1. Forced discharge of electrolytic capacitor of power supply block

When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect can occur.

In order to prevent the secondary trouble, perform the following measures before starting repair work.

Discharge procedure

1 Remove the AC power cord.

2 Connect a discharging resistor at an end of lead wire that has clips at both ends. Connect the other end of the lead wire to metal chassis.

3 Contact the other end of the discharging resistor to the positive (+) side (+VH) of C101. (For two seconds)

4 Contact the same end of the discharging resistor as step

3 to the negative (-) side (-VH) of C102 in the same way.

(For two seconds)

5 Check that voltage across C101 and C102 has decreased to 1 V or less using a multimeter or an oscilloscope.

2

MAIN C.B

D101

3

C101 C102

4

2

Select a discharging resistor referring to the following table.

Charging voltage (V)

(C101, 102)

25-48

Discharging resistor (

100

Ω

)

Rated power (W)

3

49-140 220 5

Parts number

87-A00-247-090

87-A00-232-090

Fig-1

Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the reference numbers of the charging capacitors on schematic diagram before starting the discharging work.

2. Check items before exchanging the MICROCOMPUTER

Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming that the MICROCOMPUTER is surely defective.

2-1. Regarding the HOLD terminal of the MICROCOMPUTER

When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly.

When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD terminal before exchange.

When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.

• Good or no good judgement of the MICROCOMPUTER

1 Turn on the AC main power.

2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.

3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the

MICROCOMPUTER is judged to be good.

– 4 –


In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.

2-2. Regarding reset

There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.

When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no good of the MICROCOMPUTER.

1 Remove the AC power cord.

MICR

OCOMPUTER

18

15

FRONT C.B

%

VSS

C113

MICRO-

COMPUTER

*

VDD

C113

FRONT C.B

Short with tweezers.

Fig-2-2

2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.

3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is good.

Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.

2-3. Confirmation of soldering state of MICROCOMPUTER

Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the

MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.

– 5 –


ELECTRICAL MAIN PARTS LIST

IC

REF. NO.

PART NO.

KANRI

NO.

DESCRIPTION REF. NO.

PART NO.

KANRI DESCRIPTION

NO.

C11 87-012-368-080 C-CAP,S 0.1-50 Z F

C12 87-012-368-080 C-CAP,S 0.1-50 Z F

C13 87-012-368-080 C-CAP,S 0.1-50 Z F

C14 87-012-368-080 C-CAP,S 0.1-50 Z F

C20 87-010-918-090 CAP,E 4700-50 SMG

8B-NF6-601-030 C-IC,LC876670B-5V72

87-A21-911-040 C-IC,M61515FP

87-A21-023-040 C-IC,BA3835F

87-A21-051-040 C-IC,BU9990-03FS

87-A21-831-010 IC,SPS-422-1-F1 C21 87-A12-780-090 CAP,E 4700-35 M 85 SKR

C23 87-A10-231-090 CAP,E 3300-80

C24 87-A10-231-090 CAP,E 3300-80

C31 87-A12-062-080 CAP,E 100-10 SMG

C32 87-012-286-080 C-CAP,U 0.01-25 K B

87-A21-695-010 IC,LA1845L

87-A21-928-010 IC,LC72131D-N

87-A20-783-040 C-IC,BA7762AFS

87-A21-018-040 C-IC,M65849BFP631D

87-A21-948-030 C-IC,BD3877KS2

87-A21-269-010 IC,EW732

C33 87-A12-071-080 CAP,E 47-25 SMG

C34 87-A12-089-080 CAP,E 3.3-50 SMG

C35 87-012-286-080 C-CAP,U 0.01-25 KB

C36 87-A12-062-080 CAP,E 100-10 SMG

C37 87-A12-072-080 CAP,E 100-25 SMG

TRANSISTOR

C38 87-A12-092-080 CAP,E 22-50 SMG

C39 87-A12-067-080 CAP,E 330-16 SMG

C40 87-A12-074-080 CAP,E 470-25 SMG

C101 87-012-276-080 C-CAP,U 1500P-50 K B

C102 87-012-276-080 C-CAP,U 1500P-50 K B

87-A30-559-010 TR,CSB1370EF

87-A30-076-080 C-TR,2SC3052F

87-A30-075-080 C-TR,2SA1235F

87-A30-186-010 FET,2SK3053

87-A30-107-070 C-TR,CMBT5401

C103 87-012-368-080 C-CAP,S 0.1-50 Z F

C104 87-012-368-080 C-CAP,S 0.1-50 Z F

C105 87-012-368-080 C-CAP,S 0.1-50 Z F

C106 87-012-368-080 C-CAP,S 0.1-50 Z F

C123 87-010-759-080 C-CAP,U 0.1-25 Z F

87-A30-484-080 C-TR,KRA102S

87-A30-106-040 C-TR,CMBT5551

87-A30-190-080 TR,CC5551

87-A30-204-010 TR,2SD2439

87-A30-205-010 TR,2SB1588

C124 87-010-759-080 C-CAP,U 0.1-25 Z F

C125 87-010-759-080 C-CAP,U 0.1-25 Z F

C126 87-010-759-080 C-CAP,U 0.1-25 Z F

C130 87-012-274-080 C-CAP,U 1000P-50 K B

C131 87-A12-087-080 CAP,E 1-50 SMG

87-A30-086-040 C-TR,CSD1306E

87-026-609-080 TR,KTA1266GR

87-A30-468-080 C-TR,KRC102S-RTK

87-A30-087-080 C-FET,2SK2158

87-A30-256-010 TR,2SD1933

C132 87-A12-071-080 CAP,E 47-25 SMG

C133 87-A12-071-080 CAP,E 47-25 SMG

C301 87-012-188-080 C-CAP,U 47P-50 CH

C302 87-012-188-080 C-CAP,U 47P-50 CH

C303 87-012-336-080 C-CAP,U 330P-50 J SL

87-A30-255-010 TR,2SB1342

87-A30-071-080 C-TR,RT1N 144C

87-A30-582-080 TR,CDA1585BC

87-A30-495-080 TR,2SA1981Y

87-A30-074-080 C-TR,RT1P 141C

87-026-225-080 CFET,2SJ106GR

87-A30-494-080 TR,2SA1980G

87-026-610-080 TR,KTC3198GR

87-A30-234-080 TR,CSC4115BC

87-A30-063-080 C-TR,KRA104S

C304 87-012-336-080 C-CAP,U 330P-50 J SL

C305 87-012-336-080 C-CAP,U 330P-50 J SL

C306 87-012-336-080 C-CAP,U 330P-50 J SL

C307 87-A10-262-080 C-CAP,U 1-10 Z F

C309 87-A10-260-080 C-CAP,U 0.1-16 K B

C310 87-A10-260-080 C-CAP,U 0.1-16 K B

C311 87-010-787-080 CAP,U 0.022-25 K B

C312 87-010-787-080 CAP,U 0.022-25 K B

C313 87-012-277-080 C-CAP,U 1800P-50 K B GRM

C314 87-012-277-080 C-CAP,U 1800P-50 K B GRM

87-A30-216-080 TR,2SA933AS(R)

87-A30-521-080 C-TR,2SC5345S(O)

87-A30-489-080 C-TR,KRA107S

89-503-602-080 C-FET,2SK360E

89-327-143-080 C-TR,2S2714O

MAIN C.B

C315 87-012-275-080 C-CAP,U 1200P-50 K B GRM

DIODE

C316 87-012-275-080 C-CAP,U 1200P-50 K B GRM

C321 87-A10-828-080 C-CAP,U 0.33-6.3 K B

C322 87-A10-828-080 C-CAP,U 0.33-6.3 K B

87-017-149-080 ZENER,HZS6A2L

87-A40-291-080 DIODE,1N4148M (CPT)

87-A40-673-090 DIODE,D10XB20

87-010-788-080 DIODE,1N4003 LES all-guides.com

87-A40-747-080 ZENER,UZ5.1BSB

87-A40-749-080 ZENER,UZ5.6BSB

87-A40-270-080 C-DIODE,MC2838

87-A40-269-080 C-DIODE,MC2836

C324 87-A12-071-080 CAP,E 47-25 SMG

C325 87-A12-057-080 CAP,E 330-6.3 SMG

C327 87-A12-090-080 CAP,E 4.7-50 SMG

C328 87-A12-090-080 CAP,E 4.7-50 SMG

C332 87-A10-262-080 C-CAP,U 1-10 Z F

C335 87-A12-087-080 CAP,E 1-50 SMG

C336 87-A12-087-080 CAP,E 1-50 SMG

C337 87-010-831-080 C-CAP,U 0.1-16 Z F

87-A40-764-080 ZENER,UZ10BSC C339 87-010-831-080 C-CAP,U 0.1-16 Z F

C340 87-010-831-080 C-CAP,U 0.1-16 Z F

C351 87-A10-039-080 C-CAP,U 470P-50 J CH 87-A40-488-080 DIODE,1SS244

87-A40-739-080 ZENER,UZ2.7BSA

87-A40-748-080 ZENER,UZ5.6BSA

87-A40-769-080 ZENER,UZ18BSB

87-A40-802-080 ZENER,UZ5.1BSC

C352 87-A10-039-080 C-CAP,U 470P-50 J CH

C354 87-010-175-080 C-CAP,S 560P-50 J SL

C355 87-012-274-080 C-CAP,U 1000P-50 K B

C356 87-A12-071-080 CAP,E 47-25 SMG

C357 87-012-286-080 CAP,U 0.01-25 87-A40-781-080 ZENER,UZ36BSA

87-A40-553-080 DIODE,1N4003 LES

87-A40-745-080 ZENER,UZ4.7BSA

87-A40-530-080 DIODE,RB721Q-40

C358 87-012-279-080 C-CAP,U 2700P-50 B

C359 87-012-279-080 C-CAP,U 2700P-50 B

C360 87-012-279-080 C-CAP,U 2700P-50 B

C363 87-A12-361-080 CAP,M 5600P-100 J CP

C370 87-010-831-080 C-CAP,U 0.1-16 Z F

– 6 –


REF. NO.

PART NO.

KANRI

NO.

DESCRIPTION

C373 87-A10-794-080 C-CAP,U 0.15-16 Z F

C374 87-A10-794-080 C-CAP,U 0.15-16 Z F

C378 87-010-831-080 C-CAP,U 0.1-16 Z F

C379 87-A12-069-080 CAP,E 22-25 SMG

C380 87-A12-069-080 CAP,E 22-25 SMG

C381 87-012-286-080 CAP,U 0.01-25

C382 87-012-176-080 C-CAP,U 15P-50 CH

C383 87-012-286-080 CAP,U 0.01-25

C384 87-A12-088-080 CAP,E 2.2-50 SMG

C386 87-010-831-080 C-CAP,U 0.1-16 Z F

C387 87-012-335-080 C-CAP,U 270P-50 J SL

C388 87-012-199-080 C-CAP,U 220P-50 J CH

C391 87-012-337-080 C-CAP,U 56P-50 J CH GRM

C392 87-012-337-080 C-CAP,U 56P-50 J CH GRM

C393 87-012-337-080 C-CAP,U 56P-50 J CH GRM

C394 87-012-337-080 C-CAP,U 56P-50 J CH GRM

C501 87-A12-062-080 CAP,E 100-10 SMG

C502 87-010-831-080 C-CAP,U 0.1- 16 Z F

C503 87-A10-353-080 C-CAP,U 0.22-10KB

C504 87-A10-353-080 C-CAP,U 0.22-10KB

C505 87-A10-025-080 C-CAP,U 0.22-16Z F

C506 87-012-280-080 CAP,U 3300P-50

C507 87-010-177-080 C-CAP,S 820P-50 J SL C2012

C508 87-A10-260-080 C-CAP,U 0.1-16 K B

C509 87-A10-260-080 C-CAP,U 0.1-16 K B

C510 87-012-280-080 CAP,U 3300P-50

C511 87-010-177-080 C-CAP,S 820P-50 J SL C2012

C512 87-A10-025-080 C-CAP,U 0.22-16 Z F

C513 87-A12-083-080 CAP,E 0.1-50 SMG

C514 87-A12-061-080 CAP,E 47-10 SMG

C515 87-A12-087-080 CAP,E 1-50 SMG

C516 87-A12-087-080 CAP,E 1-50 SMG

C517 87-012-279-080 C-CAP,U 2700P-50 B

C518 87-012-279-080 C-CAP,U 2700P-50 B

C531 87-A12-091-080 CAP,E 10-50 SMG

C532 87-010-831-080 C-CAP,U 0.1-16 Z F

C533 87-010-831-080 C-CAP,U 0.1-16 Z F

C534 87-012-199-080 C-CAP,U 220P-50 J CH

C535 87-012-274-080 C-CAP,U 1000P-50 K B

C536 87-010-831-080 C-CAP,U 0.1-16 Z F

C537 87-012-188-080 C-CAP,U 47P-50 CH

C538 87-012-188-080 C-CAP,U 47P-50 CH

C539 87-012-188-080 C-CAP,U 47P-50 CH

C541 87-012-274-080 C-CAP,U 1000P-50 K B

C609 87-012-277-080 C-CAP,U 1800P-50 B

C610 87-012-277-080 C-CAP,U 1800P-50 B

C611 87-010-956-080 C-CAP,S 0.068-25B

C612 87-A11-070-080 C-CAP,U 0.033-16 K B

C613 87-012-286-080 C-CAP,U 0.01-25

C614 87-012-286-080 C-CAP,U 0.01-25

C615 87-A10-260-080 C-CAP,U 0.1-16 K B

C616 87-A10-260-080 C-CAP,U 0.1-16 K B

C617 87-010-829-080 C-CAP,U 0.047-16

C618 87-A12-087-080 CAP,E 1-50 SMG

C619 87-A12-062-080 CAP,E 100-10 SMG

C620 87-012-280-080 C-CAP,U 3300P-50 K B

C623 87-A12-087-080 CAP,E 1-50 SMG

C624 87-A12-087-080 CAP,E 1-50 SMG

C626 87-A12-062-080 CAP,E 100-10 SMG

C627 87-A12-086-080 CAP,E 0.47-50 SMG

C628 87-A12-086-080 CAP,E 0.47-50 SMG

C629 87-A10-504-080 C-CAP,U 0.047-16 K B

C630 87-A10-504-080 C-CAP,U 0.047-16 K B

C631 87-012-281-080 C-CAP,U 3900P-50 B

C632 87-012-281-080 C-CAP,U 3900P-50 B

C633 87-010-831-080 C-CAP,U 0.1-16 Z F

C634 87-010-831-080 C-CAP,U 0.1-16 Z F

C635 87-A12-376-080 CAP,M 0.1-100 J CP

C636 87-A12-376-080 CAP,M 0.1-100 J CP

C637 87-A12-376-080 CAP,M 0.1-100 J CP

– 7 –

REF. NO.

PART NO.

KANRI DESCRIPTION

NO.

C638 87-A12-376-080 CAP,M 0.1-100 J CP

C639 87-A12-091-080 CAP,E 10-50 SMG

C641 87-A12-085-080 CAP,E 0.33-50 SMG

C642 87-A12-085-080 CAP,E 0.33-50 SMG

C643 87-010-831-080 C-CAP,U 0.1-16F

C644 87-A12-087-080 CAP,E 1-50 SMG

C647 87-A12-088-080 CAP,E 2.2-50 SMG

C648 87-A12-088-080 CAP,E 2.2-50 SMG

C671 87-012-195-080 C-CAP,U 100P-50CH

C672 87-012-195-080 C-CAP,U 100P-50CH

C673 87-012-286-080 CAP,U 0.01-25

C677 87-A12-085-080 CAP,E 0.33-50 SMG

C678 87-A12-085-080 CAP,E 0.33-50 SMG

C679 87-010-831-080 C-CAP,U 0.1-16 Z F

C680 87-012-286-080 C-CAP,U 0.01-25

C682 87-010-831-080 C-CAP,U 0.1-16 Z F

C698 87-012-172-080 C-CAP,U 10P-50 D CH

C699 87-012-195-080 C-CAP,U 100P-50CH

C771 87-A12-062-080 CAP,E 100-10 SMG

C772 87-012-286-080 CAP,U 0.01-25

C779 87-010-784-080 C-CAP,U 0.012-25 B

C780 87-010-784-080 C-CAP,U 0.012-25 B

C782 87-012-286-080 C-CAP,U 0.01-25

C783 87-012-286-080 C-CAP,U 0.01-25

C784 87-012-286-080 C-CAP,U 0.01-25

C785 87-012-286-080 C-CAP,U 0.01-25

C786 87-012-286-080 C-CAP,U 0.01-25

C788 87-012-167-080 C-CAP,U 5P-50 C CH

C789 87-016-116-080 C-CAP,U 0.015-25 J B CB

C790 87-016-116-080 C-CAP,U 0.015-25 J B CB

C791 87-010-831-080 C-CAP,U 0.1-16F

C792 87-012-286-080 C-CAP,U 0.01-25

C793 87-A12-090-080 CAP,E 4.7-50 SMG

C795 87-012-286-080 C-CAP,U 0.01-25

C796 87-012-286-080 C-CAP,U 0.01-25

C797 87-A12-091-080 CAP,E 10-50 SMG

C798 87-012-286-080 C-CAP,U 0.01-25

C799 87-A12-065-080 CAP,E 33-16 SMG

C800 87-010-829-080 C-CAP,U 0.047-16 F

C801 87-A12-089-080 CAP,E 3.3-50 SMG

C802 87-010-829-080 C-CAP,U 0.047-16 F

C803 87-010-787-080 C-CAP,U 0.022-25 B

C804 87-A12-062-080 CAP,E 100-10 SMG

C807 87-A12-086-080 CAP,E 0.47-50 SMG

C808 87-A12-087-080 CAP,E 1-50 SMG

C809 87-A12-087-080 CAP,E 1-50 SMG

C810 87-010-831-080 C-CAP,U 0.1-16F

C811 87-A12-089-080 CAP,E 3.3-50 SMG

C812 87-A12-089-080 CAP,E 3.3-50 SMG

C814 87-012-286-080 C-CAP,U 0.01-25

C815 87-A12-086-080 CAP,E 0.47-50 SMG

C816 87-A12-086-080 CAP,E 0.47-50 SMG

C821 87-A12-091-080 CAP,E 10-50 SMG

C823 87-010-177-080 C-CAP,S 820P-50 J SL C2012

C824 87-A12-090-080 CAP,E 4.7-50 SMG

C825 87-A10-504-080 C-CAP,U 0.047-16 K B

C842 87-012-286-080 C-CAP,U 0.01-25 B

C844 87-012-286-080 C-CAP,U 0.01-25 B

C850 87-A12-071-080 CAP,E 47-25 SMG

C851 87-012-286-080 C-CAP,U 0.01-25 B

C852 87-012-286-080 C-CAP,U 0.01-25 B

C853 87-012-286-080 C-CAP,U 0.01-25 B

C858 87-010-831-080 C-CAP,U 0.1-16F

C901 87-018-145-080 CAP,TC-U 6.8P-50 CH

C904 87-012-286-080 C-CAP,U 0.01-25 B

C905 87-012-286-080 C-CAP,U 0.01-25 B

C907 87-012-286-080 C-CAP,U 0.01-25 B

C908 87-A10-915-080 C-CAP,U 1000P-25 J CH

C909 87-012-286-080 C-CAP,U 0.01-25 B

C910 87-012-174-080 C-CAP,U 12P-50 CH


REF. NO.

PART NO.

KANRI

NO.

DESCRIPTION

C911 87-012-170-080 C-CAP,U 8P-50 D CH

C912 87-012-195-080 C-CAP,U 100P-50 J CH

C913 87-012-286-080 C-CAP,U 0.01-25 B

C914 87-012-166-080 C-CAP,U 4P-50 C CH

C915 87-012-174-080 C-CAP,U 12P-50 CH

C916 87-012-180-080 C-CAP,U 22P-50 CH

C917 87-012-186-080 C-CAP,U 39P-50 CH

C918 87-A10-039-080 C-CAP,U 470P-50 J CH

C921 87-012-195-080 C-CAP,U 100P-50 CH

C922 87-012-174-080 C-CAP,U 12P-50 CH

C959 87-010-831-080 C-CAP,U 0.1-16F

C960 87-010-831-080 C-CAP,U 0.1-16F

C961 87-012-167-080 C-CAP,U 5P-50 CH

C963 87-015-785-080 C-CAP,0.1-25 Z F C3216

C971 87-A12-067-080 CAP,E 330-16 SMG

C972 87-A12-090-080 CAP,E 4.7-50 SMG

C973 87-012-286-080 C-CAP,U 0.01-25

C974 87-012-286-080 C-CAP,U 0.01-25

C979 87-012-195-080 C-CAP,U 100P-50CH

C981 87-A12-071-080 CAP,E 47-25 SMG

C982 87-010-831-080 C-CAP,U 0.1-16F

C983 87-012-286-080 C-CAP,U 0.01-25

C984 87-012-286-080 C-CAP,U 0.01-25

C987 87-012-286-080 C-CAP,U 0.01-25

C991 87-012-176-080 C-CAP,U 15P-50 CH

C992 87-012-176-080 C-CAP,U 15P-50 CH

C993 87-012-274-080 C-CAP,U 1000P-50B

C995 87-012-274-080 C-CAP,U 1000P-50B

C997 87-010-831-080 C-CAP,U 0.1-16F

C998 87-A12-071-080 CAP,E 47-25 SMG

C999 87-A11-155-080 CAP,TC U 0.01-16 Z F

CF831 87-008-261-010 FILTER,CF SFE10.7MA5-A

CF832 87-008-261-010 FILTER,CF SFE10.7MA5-A

CN11 87-A60-996-010 CONN,13P V BLK TAC-L13X-A3

CN12 87-A61-108-010 CONN,5P V TID-A

CN131 87-A60-619-010 CONN,2P V 2MM JMT

CN132 87-A60-619-010 CONN,2P V 2MM JMT

CN301 87-A60-620-010 CONN,3P V 2MM JMT

CN351 87-A60-625-010 CONN,8P V 2MM JMT

CN601 87-099-719-010 CONN,30P TYK-B(X)

CN602 87-099-194-010 CONN,6P V BLK 6216

CN604 87-099-749-010 CONN,9P V 9604SC

CN607 87-A60-996-010 CONN,13P V BLK TAC-L13X-A3

CNA11 8A-NF8-653-010 CONN ASSY,9P TID-A(480)

CNA12 8B-NF7-618-010 CONN ASSY,3P V PANO

CNA101 8B-NF6-660-010 CONN ASSY,2P V PANO(250)

D902 87-A40-128-080 C-VARI-CAP,HVA202A

D903 87-A40-128-080 C-VARI-CAP,HVA202A

FB501 87-008-372-080 FILTER, EMI BL 01 RN1

FFC602 88-906-251-110 FF-CABLE,6P 1.25

FFC604 88-909-141-110 FF-CABLE,9P 1.25 140MM

J101 87-A60-929-010 JACK,DIA6.3 BLK ST W/S TAI

J102 87-A60-238-010 TERMINAL,SP 4P (MSC)

J104 87-A60-881-010 JACK,PIN 2P MSP 242V05 PBSN

J601 87-A60-885-010 JACK,PIN 6P R/W MSC

J831 87-A60-202-010 TERMINAL,ANT 4P MSP-154V-02

L101 87-A50-610-010 COIL,1UH K(MDEC)

L102 87-A50-610-010 COIL,1UH K(MDEC)

L121 87-A50-610-010 COIL,1UH K(MDEC)

L122 87-A50-610-010 COIL,1UH K(MDEC)

L301 87-A50-625-010 COIL,TRAP 85KHZ (SANWA)

L302 87-A50-625-010 COIL,TRAP 85KHZ (SANWA)

L351 87-007-342-010 COIL,OSC 85KHZ BIAS

L801 87-A50-608-010 COIL,FM DET-N(TOK)

L802 87-A91-551-010 FLTR,PCFJZH-450 L(TOK)

L811 87-005-847-080 COIL,2.2UH(CECS)

L832 87-005-847-080 COIL,2.2UH(CECS)

L902 88-ZA1-602-110 COIL,FM-RF-U2 2G

L903 88-ZA1-601-010 COIL,FM-RF-U1 2G

L904 87-005-847-080 COIL,2.2UH(CECS)

REF. NO.

PART NO.

KANRI DESCRIPTION

NO.

L905 88-ZA1-624-010 COIL,FM IFT 7-6.2(COILS)

L906 88-ZA1-603-010 COIL,FM-OSC-U 2G

L951 8A-NF8-667-010 COIL,AM PACK 4(TOK)

R151 87-A00-879-050 RES,M/F 270-1W J

R152 87-A00-879-050 RES,M/F 270-1W J

R153 87-A00-879-050 RES,M/F 270-1W J

R154 87-A00-879-050 RES,M/F 270-1W J

R790 87-012-286-080 C-CAP,U 0.01-25 B

R991 87-012-195-080 C-CAP,U 100P-50CH

R993 87-012-195-080 C-CAP,U 100P-50CH

R995 87-012-195-080 C-CAP,U 100P-50CH

SFR351 87-024-436-080 SFR,47K H RH063MC

SFR352 87-024-436-080 SFR,47K H RH063MC

WH11 87-A91-179-010 HLDR,WIRE 2.5-11P

X992 87-A70-306-010 VIB,XTAL 4.500MHZ CSA-309ST

– 8 –

FRONT C.B

C113 87-010-788-080 C-CAP,U 0.33-25 Z F

C201 87-016-083-080 C-CAP,S 0.15-16 K R

C202 87-012-270-080 CAP,U 470P-50 K B

C207 87-010-590-080 C-CAP,S 0.015-16 K R

C301 87-012-180-080 C-CAP,U 22P-50 J CH

C302 87-012-180-080 C-CAP,U 22P-50 J CH

C303 87-012-180-080 C-CAP,U 22P-50 J CH

C304 87-012-180-080 C-CAP,U 22P-50 J CH

C305 87-012-180-080 C-CAP,U 22P-50 J CH

C306 87-010-759-080 C-CAP,U 0.1-25 Z F

C307 87-A12-317-080 C-CAP,U 0.1-50 Z F

C351 87-012-188-080 C-CAP,U 47P-50 J CH

C352 87-012-188-080 C-CAP,U 47P-50 J CH

C353 87-012-188-080 C-CAP,U 47P-50 J CH

C354 87-012-188-080 C-CAP,U 47P-50 J CH

C355 87-012-188-080 C-CAP,U 47P-50 J CH

C383 87-010-759-080 C-CAP,U 0.1-25 Z F

C384 87-010-759-080 C-CAP,U 0.1-25 Z F

C385 87-010-759-080 C-CAP,U 0.1-25 Z F

C386 87-010-759-080 C-CAP,U 0.1-25 Z F

C387 87-010-759-080 C-CAP,U 0.1-25 Z F

C601 87-012-282-080 CAP,U 4700P-50 K B

C602 87-010-405-040 CAP,E 10-50 M 11L SME

C605 87-A12-317-080 C-CAP,U 0.1-50 Z F

C606 87-010-112-040 CAP,E 100-16 M 11L SME

C607 87-010-759-080 C-CAP,U 0.1-25 Z F

C611 87-012-274-080 C-CAP,U 1000P-50 K B

C612 87-010-546-040 CAP,E 0.33-50 M 11L SME

C613 87-012-191-080 C-CAP,U 68P-50 J CH

C614 87-012-274-080 C-CAP,U 1000P-50 K B

C652 87-012-279-080 C-CAP,U 2700P-50 K B GRM

C653 87-010-785-080 C-CAP,U 0.015-25 K B GRM

C701 87-010-406-040 CAP,E 22-50 M 11L SME

C901 87-010-759-080 C-CAP,U 0.1-25 Z F

C902 87-012-335-080 C-CAP,U 270P-50 J SL

C903 87-012-195-080 C-CAP,U 100P-50 J CH

C904 87-010-596-080 C-CAP,S 0.047-16 K R C2012

C905 87-012-176-080 C-CAP,U 15P-50 J CH

C906 87-A10-189-040 CAP,E 220-10 M 5L

C908 87-012-274-080 C-CAP,U 1000P-50 K B

C909 87-012-286-080 C-CAP,U 0.01-25 K B

C910 87-012-270-080 C-CAP,U 470P-50 K B

C911 87-012-199-080 C-CAP,U 220P-50 J CH

C912 87-012-199-080 C-CAP,U 220P-50 J CH

C913 87-012-199-080 C-CAP,U 220P-50 J CH

C914 87-012-199-080 C-CAP,U 220P-50 J CH

C915 87-012-199-080 C-CAP,U 220P-50 J CH

C916 87-012-199-080 C-CAP,U 220P-50 J CH

C917 87-012-199-080 C-CAP,U 220P-50 J CH

C918 87-012-199-080 C-CAP,U 220P-50 J CH

C919 87-012-199-080 C-CAP,U 220P-50 J CH

C920 87-012-199-080 C-CAP,U 220P-50 J CH


REF. NO.

PART NO.

KANRI DESCRIPTION

NO.

C921 87-012-270-080 C-CAP,U 470P-50 K B

C923 87-010-759-080 C-CAP,U 0.1-25 Z F

C925 87-A12-317-080 C-CAP,U 0.1-50 Z F

C926 87-010-759-080 C-CAP,U 0.1-25 Z F

C927 87-010-759-080 C-CAP,U 0.1-25 Z F

C928 87-010-408-040 CAP,E 47-50 M 11L SME

C929 87-012-369-080 C-CAP,S 0.047-50 Z F

C931 87-010-404-040 CAP,E 4.7-50 M 11L SME

C933 87-010-404-040 CAP,E 4.7-50 M 11L SME

C991 87-010-405-040 CAP,E 10-50 M 11L SME

C992 87-012-336-080 C-CAP,U 330P-50 J SL

CN101 87-099-720-010 CONN,30P BLK TYK-B(P)

CN104 87-099-017-010 CONN,15P V BLK 6216

CN151 87-099-196-010 CONN,8P V BLK 6216

CN801 87-099-212-010 CONN,5P V BLK 6216

FB301 87-008-372-080 FLTR,EMI BL01 RN1

FB601 87-008-372-080 FLTR,EMI BL01 RN1

FFC104 88-915-181-110 FF-CABLE,15P 1.25 180MM

FFC151 88-908-301-110 FF-CABLE,8P 1.25

FFC801 88-905-061-110 FF-CABLE,5P 1.25 60MM

FL901 8B-NF7-621-010 FL,BJ815GNK

J601 87-A61-242-010 JACK,6.3 BLK MONO W/SW V KM

J602 87-A61-242-010 JACK,6.3 BLK MONO W/SW V KM

L901 87-A50-657-010 COIL,CLK 9.43MHZ (TOKO)7KLY

LED201 87-A40-317-080 LED,SLR-342VCT31 RED

LED401 87-A40-268-080 LED,SLH-56DCT31 ORN





S301 87-A90-164-080 SW,TACT SKQNAB(N)









S351 8B-NF6-218-010 HLDR,TS CRAMP








KEY C.B

C501 87-010-759-080 C-CAP,U 0.1-25 Z F

C502 87-A12-317-080 C-CAP,U 0.1-50 Z F

C531 87-012-180-080 C-CAP,U 22P-50 J CH

C532 87-012-180-080 C-CAP,U 22P-50 J CH

C533 87-012-180-080 C-CAP,U 22P-50 J CH

C534 87-012-180-080 C-CAP,U 22P-50 J CH

C535 87-012-180-080 C-CAP,U 22P-50 J CH

C536 87-012-180-080 C-CAP,U 22P-50 J CH

C537 87-012-180-080 C-CAP,U 22P-50 J CH

C571 87-012-188-080 C-CAP,U 47P-50 J CH

C572 87-012-188-080 C-CAP,U 47P-50 J CH

C573 87-012-188-080 C-CAP,U 47P-50 J CH

C574 87-012-188-080 C-CAP,U 47P-50 J CH

C575 87-012-188-080 C-CAP,U 47P-50 J CH

C576 87-012-188-080 C-CAP,U 47P-50 J CH

C577 87-012-188-080 C-CAP,U 47P-50 J CH

C581 87-012-274-080 C-CAP,U 1000P-50 K B

C582 87-012-195-080 C-CAP,U 100P-50 J CH

C583 87-012-195-080 C-CAP,U 100P-50 J CH

C591 87-012-274-080 C-CAP,U 1000P-50 K B

– 9 –

REF. NO.

PART NO.

KANRI DESCRIPTION

NO.

C592 87-012-195-080 C-CAP,U 100P-50 J CH

C593 87-012-195-080 C-CAP,U 100P-50 J CH

C802 87-012-197-080 C-CAP,U 150P-50 J CH

C804 87-012-283-080 C-CAP,U 5600P-50 K B

C805 87-010-831-080 C-CAP,U 0.1-16 Z F

C806 87-010-401-040 CAP,E 1-50 M 11L SME

C808 87-010-831-080 C-CAP,U 0.1-16 Z F

C809 87-012-198-080 C-CAP,U 180P-50 J CH

C810 87-010-263-040 CAP,E 100-10 M 11L SME

C811 87-010-545-040 CAP,E 0.22-50 M 11L SME

C812 87-010-405-040 CAP,E 10-50 M 11L SME

CN501 8B-NF6-606-010 CONN ASSY,6P DADA



CN802 87-099-212-010 CONN,5P V BLK 6216

FB501 87-008-372-080 FLTR,EMI BL01 RN1

FB801 87-008-372-080 FLTR,EMI BL01 RN1

L801 87-A50-093-010 COIL,CLOCK OSC 5.76MHZ

L802 87-005-847-080 COIL,2.2UH K CECS

LED501 87-A40-496-040 LED,SLR-342PCT31 GRN



LED511 87-A40-619-040 LED,SLR-56PT-T31-W GRN


































S571 8B-NF6-219-010 HLDR,TS CRAMP SLNT








S581 87-A92-114-010 SW,RTRY EC12E24504 30MM

S591 87-A92-113-010 SW,RTRY EC12E12504 30MM

AMP 3M C.B


REF. NO.

PART NO.

KANRI DESCRIPTION

NO.

C1 87-010-759-080 C-CAP,U 0.1-25 Z F

C2 87-010-759-080 C-CAP,U 0.1-25 Z F

C3 87-010-759-080 C-CAP,U 0.1-25 Z F

C4 87-010-759-080 C-CAP,U 0.1-25 Z F

C15 87-010-759-080 C-CAP,U 0.1-25 Z F

C17 87-016-299-080 CAP,E 10-100 M SME

C18 87-010-866-080 CAP,E 10-63 M VX

C101 87-012-276-080 C-CAP,U 1500P-50 K B

C102 87-012-276-080 C-CAP,U 1500P-50 K B

C103 87-A12-085-080 CAP,E 0.33-50 SMG

C104 87-A12-085-080 CAP,E 0.33-50 SMG

C105 87-012-279-080 C-CAP,U 2700P-50 K B GRM

C106 87-012-279-080 C-CAP,U 2700P-50 K B GRM

C107 87-A12-090-080 CAP,E 4.7-50 SMG

C108 87-A12-090-080 CAP,E 4.7-50 SMG

C111 87-A12-077-080 CAP,E 33-35 SMG

C112 87-A12-077-080 CAP,E 33-35 SMG

C115 87-010-177-080 C-CAP,S 820P-50 J SL C2012

C116 87-010-177-080 C-CAP,S 820P-50 J SL C2012

C117 87-A10-596-080 C-CAP,S 100P-100 J CH

C118 87-A10-596-080 C-CAP,S 100P-100 J CH

C119 87-012-368-080 C-CAP,S 0.1-50 Z F

C120 87-012-368-080 C-CAP,S 0.1-50 Z F

C121 87-A10-596-080 C-CAP,S 100P-100 J CH

C122 87-A10-596-080 C-CAP,S 100P-100 J CH

C141 87-012-282-080 C-CAP,U 4700P-50 K B

C142 87-012-278-080 C-CAP,U 2200P-50 K B

C151 87-012-286-080 C-CAP,U 0.01-25 K B

C152 87-012-286-080 C-CAP,U 0.01-25 K B

C161 87-010-759-080 C-CAP,U 0.1-25 Z F

CN1 87-A61-011-010 CONN,13P H BLK TAC-L13P-A3

CN102 87-A61-011-010 CONN,13P H BLK TAC-L13P-A3

CNA1 8B-NF6-645-010 CONN ASSY,5P TID-A(110)

R171 87-A00-418-010 RES,M/F 0.15-3W J

R172 87-A00-418-010 RES,M/F 0.15-3W J

R173 87-A00-418-010 RES,M/F 0.15-3W J

R174 87-A00-418-010 RES,M/F 0.15-3W J

TH101 87-A91-042-080 C-THMS,100K 55001

TH102 87-A91-042-080 C-THMS,100K 55001

WH1 87-A90-459-010 HLDR,WIRE 2.5-5P

PANORAMA AMP C.B

C201 87-A12-088-080 CAP,E 2.2-50 SMG

C202 87-A12-088-080 CAP,E 2.2-50 SMG

C203 87-A12-062-080 CAP,E 100-10 SMG

C204 87-A12-062-080 CAP,E 100-10 SMG

C207 87-012-286-080 C-CAP,U 0.01-25 K B

C208 87-012-286-080 C-CAP,U 0.01-25 K B

C213 87-012-172-080 C-CAP,U 10P-50 D CH

C215 87-010-831-080 C-CAP,U 0.1-16 Z F

C216 87-010-831-080 C-CAP,U 0.1-16 Z F

C301 87-012-280-080 CAP,U 3300P-50 K B

C302 87-012-280-080 CAP,U 3300P-50 K B

C303 87-A12-084-080 CAP,E 0.22-50 SMG

C304 87-A12-084-080 CAP,E 0.22-50 SMG

C309 87-A12-089-080 CAP,E 3.3-50 SMG

C310 87-A12-089-080 CAP,E 3.3-50 SMG

REF. NO.

PART NO.

KANRI DESCRIPTION

NO.

C311 87-A12-092-080 CAP,E 22-50 SMG

C312 87-A12-092-080 CAP,E 22-50 SMG

C315 87-012-199-080 C-CAP,U 220P-50 J CH

C316 87-012-199-080 C-CAP,U 220P-50 J CH

C317 87-012-286-080 C-CAP,U 0.01-25 K B

C318 87-012-286-080 C-CAP,U 0.01-25 K B

C401 87-010-831-080 C-CAP,U 0.1-16 Z F

C402 87-010-831-080 C-CAP,U 0.1-16 Z F

C403 87-A12-091-080 CAP,E 10-50 SMG

C404 87-A12-091-080 CAP,E 10-50 SMG

C501 87-012-282-080 C-CAP,U 4700P-50 K B

C502 87-012-278-080 C-CAP,U 2200P-50 K B

CN101 87-099-197-010 CONN,9P V BLK 6216

CN102 87-099-043-010 CONN,2P V WHT EH

CN104 87-049-919-010 CONN,3P V WHT EH

R333 87-A00-258-080 RES,M/F 0.22-1W J

R334 87-A00-258-080 RES,M/F 0.22-1W J

PT C.B

!

!

!

!

CN1 87-A61-110-010 CONN,9P V TID-A

PT1 8B-NF6-611-010 PT,BNF-6 LH

PT2 8B-MA6-673-010 PT,SUB BMA H (VRK)

RY1 87-A91-339-010 RELAY,AC DC12V G5PA-2

S1 87-A90-165-010 SW,SL 1-2-3 SWS2301

!

!

T1 87-A60-317-010 TERMINAL,1P MSC

T2 87-A60-317-010 TERMINAL,1P MSC

DECK C.B

CON502 87-099-756-010 CONN,15P H 9604S F

SFR1 87-024-581-010 SFR,3.3K H KVSF637A

SOL1 82-ZM3-627-010 SOL ASSY,27 SO

SOL2 82-ZM3-627-010 SOL ASSY,27 SO

SW1 87-A90-248-010 SW,MICRO ESE11SH2CXQ



SW4 87-036-110-010 SW,MICRO SPPB62

SW5 87-036-110-010 SW,MICRO SPPB62

SW6 87-036-110-010 SW,MICRO SPPB62



HEAD-1 C.B

CON301 87-NF6-615-010 CONN ASSY,3P PB

HEAD-2 C.B

CON351 87-NF6-616-010 CONN ASSY,8P RPB

– 10 –


Chip resistor

Wattage

1/16W

1/16W

1/10W

1/8W

CHIP RESISTOR PART CODE

Chip Resistor Part Coding

8 8

A

Resistor Code

Type

1005

1608

2125

3216

Tolerance

5%

5%

5%

5%

Symbol

CJ

CJ

CJ

CJ

Figure

Value of resistor

Form

L

W

Dimensions (mm)

L W t

1.0

0.5

0.35

t

1.6

0.8

0.45

2 1.25

0.45

3.2

1.6

0.55

: A

Resistor Code : A

104

108

118

128 all-guides.com

– 11 –


TRANSISTOR ILLUSTRATION

B C E

CSB1370EF

G

S

D

2SJ106GR

E C B

CDA1585BC

CSC4115BC

KTA1266GR

KTC3198GR

E C B

CC5551

2SA1980G

2SA1981Y

E C B

2SA933AS(R)

B C E

2SB1342

2SB1588

2SD1933

2SD2439

D

G

S

2SK2158

C

B

E

2SA1235F

2SC2714O

2SC3052F

2SC5345S(O)

CMBT5401

CMBT5551

CSD1306E

KRA102S

KRA104S

KRA107S

KRC102S-RTK

RT1N 144C

RT1P 141C

G D S

2SK3053

S

D

G

2SK360E

– 12 –


WIRING 1 (MAIN)

32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

R

S

T

U

M

N

O

P

Q

J

K

L

I

G

H

D

E

F

A

B

C

13


SCHEMATIC DIAGRAM – 1 (MAIN : 1 / 6 <P – SUPPLY SECTION>)

– 14 –

SCHEMATIC DIAGRAM – 2 (MAIN : 2 / 6 <FUNCTION SECTION>)


– 15 –

SCHEMATIC DIAGRAM – 3 (MAIN : 3 / 6 <AMP SECTION>)


all-guides.com

– 16 –


SCHEMATIC DIAGRAM – 4 (MAIN : 4 / 6 <DECK SECTION / HEAD – 1 / HEAD – 2>)

– 17 –

SCHEMATIC DIAGRAM – 5 (MAIN : 5 / 6 <DSP SECTION>)


– 18 –

SCHEMATIC DIAGRAM – 6 (MAIN : 6 / 6 <TUNER SECTION>)


– 19 –


WIRING 2 (FRONT)

32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

R

S

T

U

M

N

O

P

Q

J

K

L

I

G

H

D

E

F

A

B

C

20


WIRING 3 (KEY)

32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

R

S

T

U

M

N

O

P

Q

J

K

L

I

G

H

D

E

F

A

B

C all-guides.com

21

SCHEMATIC DIAGRAM – 7 (FRONT / KEY / DECK)


– 22 –


WIRING 4 (AMP 3M)

32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

R

S

T

U

M

N

O

P

Q

J

K

L

I

G

H

D

E

F

A

B

C

23

SCHEMATIC DIAGRAM – 8 (AMP 3M)


– 24 –


WIRING 5 (PANORAMA AMP)

32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

R

S

T

U

M

N

O

P

Q

J

K

L

I

G

H

D

E

F

A

B

C

25

SCHEMATIC DIAGRAM – 9 (PANORAMA AMP)



WIRING 6 (PT)

32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

R

S

T

U

M

N

O

P

Q

J

K

L

I

G

H

D

E

F

A

B

C

27

SCHEMATIC DIAGRAM – 10 (PT)


– 28 –


WIRING 7 (DECK / HEAD 1 / HEAD 2)

32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

R

S

T

U

M

N

O

P

Q

J

K

L

I

G

H

D

E

F

A

B

C

29


FL (BJ815GNK) GRID ASSIGNMENT / PIN CONNECTION / ANODE CONNECTION

GRID ASSIGNMENT

PIN CONNECTION

30

ANODE CONNECTION


NOTE:

= (UP)

= (DOWN) all-guides.com

31

IC BLOCK DIAGRAM


32


33


IC DESCRIPTION

IC, LC876670B–5V72

14

15

16

17

10

11

12

13

6

7

8

9

4

5

Pin No.

1

2

3

22

23

24

25

26

18

19

20

21

27

28

29

30~41

50

51

52

53~56

57

58

59

42~45

46

47

48

49

Pin Name

I–SUBQ

O–BUZ

O–MOTOR

O–SOL1

O–SOL2

O–RSM–CE

O–HSP

O–PANORAMA

O–MUTE

O–CLK–SFT

RESET

I–DISH

I–SPEANA / I–MS

VSS1

CF1

CF2

VDD1

I–HOLD

I–KEY1

I–KEY2

I–KEY3

I–CDSW

I–RT–VR

I–RT–JOG

I–MIC

I–TM–BASE

O–CD–DATA

O–POWER

I-RMC

G12~G1

P35~P32

VDD3

SPEANA–A / P31

SPEANA–B / P30

SPEANA–C / P29

I–HPMUTE / P28 I/O

–VP —

I–STEREO / P27

P26~P23

I/O

O

BEAT–M / P22

KCON / P21

DSP / P20

I/O

I/O

I/O

O

O

O

O

—

—

I

O

—

I

I

O

—

O

O

O

O

O

O

I/O

I

O

O

I

I

I

I

I

I

I

I

I

I

O

O

O

Description

CD sub-code input.

Touch-sensor beep sound output. (Not used)

Tape motor ON/OFF.

Tape 1 plunger ON/OFF.

Tape 2 plunger ON/OFF.

Rhythm IC chip enable output.

PLL-IC chip enable output.

Panoramic IC data output.

Mute output. Mute ON/OFF.

System microcomputer clock shift ON/OFF output.

System reset.

CD turn-table position detection AD input.

Spectrum analyzer level / MS input. AD input.

Connected to GND.

Oscillator circuit input.

Oscillator circuit output.

Connected to power supply.

System power observation AD input.

KEY 1 AD input.

KEY 2 AD input.

KEY 3 AD input.

CD mechanical switch AD input.

VOLUME rotary encoder AD input.

JOG rotary encoder AD input.

Auto VF microphone input. Small signal detection (MIC IN) input.

Time base input.

CD data output.

System power ON/OFF output.

Remote-control signal reception input. Active at “L”.

FL grid G12~G1 output.

FL segment P35~P32 output.


Spectrum analyzer band switching output A / FL segment P31 output.

Spectrum analyzer band switching output B / FL segment P30 output.

Spectrum analyzer band switching output C / FL segment P29 output.

Headphone MUTE input / FL segment P28 output.

Power supply for FL display.

Tuner stereo detect input / FL segment P27 output.

FL segment P26~P23 output.

Beat master diode input / FL segment P22 output.

KCON enable diode input (Not used) / FL segment P21 output.

DSP enable diode input / FL segment P20 output.

– 34 –


73

74

75

76

69

70

71

72

Pin No.

60

61

62

63

64

65

66

67

68

81

82

83

84

85

77

78

79

80

86

87

88

89

95

96

97

98

99

100

90

91

92

93

94

Pin Name

DOLBY / P19

I/O

I/O

CASINO / P18 I/O

KARAOKE / P17 I/O

PANORAMA / P16 I/O

DEMO / P15 I/O

ECO / P14

OIRT / P13

SW / P12

LW / P11

I/O

I/O

I/O

I/O

AMST / P10

AM10K / P9

CST2 / P8

VDD4

REB / P7

CAM2 / P6

AUTO1 / P5

AUTO2 / P4

I/O

I/O

I/O

I/O

I/O

I/O

I/O

—

CAM1 / P3

CST1 / P2

REA / P1

O–CD–CE

I–DRF / IFC

I–WRQ

O–LED–JOG

O–LED–VOL

O–LED–TUNER

O–LED–MD

O–LED–AUX

O–LED–TAPE

VSS2

O

O

O

I

I

I/O

I/O

I/O

O

O

O

O

—

VDD2

O–LED–CD

O–LED–CD1

O–LED–CD2

O–LED–CD3

O–KSCAN

O–PLL–CE

O–M–STB

O–M–CLK

O–M–DATA

O–CD–CLK

O

O

O

O

O

O

O

O

O

—

O

Description

DOLBY enable diode input (Not used) / FL segment P19 output.

Casino DEMO diode input / FL segment P18 output.

Karaoke enable diode input (Not used) / FL segment P17 output.

Panorama enable diode input (Not used) / FL segment P16 output.

Demonstration OFF diode input (Not used) / FL segment P15 output.

Initial echo OFF diode input / FL segment P14 output.

OIRT diode input (Not used) / FL segment P13 output.

SW diode input (Not used) / FL segment P12 output.

LW diode input (Not used) / FL segment P11 output.

AMST diode input (Not used) / FL segment P10 output.

AM10K diode input / FL segment P9 output.

CST2 diode input / FL segment P8 output.


REB diode input / FL segment P7 output.

CAM2 diode input / FL segment P6 output.

AUTO1 diode input / FL segment P5 output.

AUTO2 diode input / FL segment P4 output.

CAM1 diode input / FL segment P3 output.

CST1 diode input / FL segment P2 output.

REA diode input / FL segment P1 output.

CD chip enable output.

CD DRF input / TUNER IFC input.

CD write request input.

JOG flash ring LED indicator ON/OFF.

VOL flash ring LED indicator ON/OFF.

TUNER function LED ON/OFF.

MD function LED ON/OFF.

AUX function LED ON/OFF.

TAPE function LED ON/OFF.

Connected to GND.


CD function LED ON/OFF.

CD1 direct button LED ON/OFF.



“L” at key-scan timing switching retrieve.

PLL-IC chip enable output.

Main C.B strobe output.

Main C.B clock output.

Main C.B data output.

CD clock output.

– 35 –


ADJUSTMENT < DECK / TUNER / FRONT >

G DECK C.B

SFR1

1

RVS

7

4 FWD

A MAIN C.B

SFR351 SFR352

J101

1

2

3

4

5

6

7

8

9

<DECK SECTION>

Requirements

1. Adjusting Tape Speed (DECK 2)

• Measuring Device: WOW & FLUTTER Meter (Frequency Counter) all-guides.com

Test Point: HP OUT (J101)

Adjustment Point: SFR 1

1) Connect the WOW & FLUTTER Meter to the HP OUT.

2) Insert the test tape (TTA-100) into DECK 2, FWD playback the centre of the tape and adjust SFR1 until it becomes 3,000 Hz

±

5 Hz.

3) RVS playback and check that

±

45 Hz is added according to the FWD speed.

2. Checking Tape Speed (DECK 1)

Requirements

Same as number 1

1) Insert the test tape (TTA-100) into DECK 1, playback the centre of the tape and check that the speed is within

±

45 Hz according to the speed of DECK 2.

– 36 –

HP OUT

WOW &FLUTTER METER

Hz

INPUT

%


3. Checking WOW & FLUTTER (DECK 1, DECK 2)

Requirements

Same as number 1

1) Connect the WOW & FLUTTER Meter to the HP OUT.

2) Set the indicator to JIS and the mode to W RMS (WTD) of the WOW & FLUTTER.

3) Playback the centre of the test tape (TTA-100) and check that it is below 0.21 %.

4. Checking Adjusting Head Azimuth (DECK 1, DECK 2)

Requirements

• Measuring Device: Oscilloscope

Test Tape: TTA-300 (10 kHz)

Test Point: TP8 (Lch), TP9 (Rch)

Adjustment Point: Head Azimuth Screws

1) Connect the CH1 probe of the oscilloscope to TP8 (Lch) and the CH2 probe of the oscilloscope to TP9 (Rch).

2) Set the V mode of the oscilloscope to ADD.

3) Insert the test tape (TTA-300) into DECK 1, FWD playback the centre of the tape and adjust, using the head azimuth screws until the waveform of the oscilloscope has reached the maximum when playing back at 10 kHz.

4) Reverse the tape, RVS playback and adjust, using the head azimuth screws until the waveform of the oscilloscope has reached its maximum.

5) After the adjustment, bond lock (1600 B) the screws.

6) Perform the same operation from 3) to 5) for DECK 2.

5. Checking Playback Frequency (DECK 1, DECK 2)

Requirements

• Measuring Device: Millivoltmeter

Test Tape: TTA-330 (315 Hz/8 kHz)


1) Connect CH1 of the millivoltmeter to TP8 (Lch) and CH2 of the millivoltmeter to TP9 (Rch).

2) Insert the test tape (TTA-300) into DECK 1 and playback at 315 Hz and 10 kHz.

3) Use the 315 Hz output level as a standard, check that the 8 kHz level is within

±

3 dB.


6. Checking Playback Sensitivity (DECK 1, DECK 2)

Requirements

• Measuring Device: Millivoltmeter

Test Tape: TTA-200 (400 Hz)



2) Insert the tape (TTA-200) into DECK 1 and playback.

3) Check that the output level is within 300 mV

±

30 mV.


TP8

TP9

CH1

OSCILLOSCOPE

OUTPUT

CH2

AC MILLIVOLTMETER

TP8

TP9

CH1 CH2

7. Adjusting REC / PB Frequency Response (DECK 2)

Requirements

• Measuring Devices: Millivoltmeter, Audio Signal Generator

(Low Frequency Generator) Attenuator

Test Tape: TTA-602 (NORMAL)

Test Point: TP8 (Lch) , TP9 (Rch)

Input Point: AUX (1 kHz/10 kHz)

Adjustment Point: SFR351 (Lch), SFR352 (Rch)

1) Connect CH1 of the millivoltmeter to TP8 (Lch) and

CH2 of the millivoltmeter to TP9 (Rch).

AUDIO SIGNAL

GENERATOR

OUTPUT

(1kHz, 1V)

– 37 –

ATTENUATOR

INPUT OUTPUT

AUX(L)

AUX(R)

SET

TP8

TP9

AC MILLIVOLTMETER

CH1 CH2


2) Connect the output from the generator to the attenuator and connect the AUX from the set to the attenuator.

3) Insert the tape (TTA-602) into DECK 2 and record the 1 kHz signal from AUX.

4) At this time, adjust the attenuator until TP8 and TP9 output levels become 21 mV.

5) Record 1 kHz and 10 kHz alternately.

6) Adjust SFR351 (Lch)/SFR352 (Rch) until the playback output level of 10 kHz is within 0.5

±

0.5 dB according to the standard when the playback output level of 1 kHz is used as the standard.

8. Checking REC/ PB Frequency Response (DECK 2)

Requirements

• Measuring Devices: Same as 7

Test Tape: TTA-615 (CrO2)


Input Point: AUX (1 kHz/10 kHz)




4) At this time, adjust the attenuator until the TP8 and TP9 output levels become 21 mV.

5) Record 1 kHz and 10 kHz alternately.

6) Check the output level of 10 kHz is within

±

2.5 dB according to the standard when the playback output level of 1 kHz is used as the standard.

9. Checking REC/ PB Sensitivity (DECK 2)

Requirements

• Measuring Devices: Millivoltmeter, Audio Signal Generator (Low Frequency Generator), Attenuator

Test Tape: TTA-602 (NORMAL)

TTA-615 (CrO2)


Input Point: AUX (1 kHz)

1) Connect CH1 of the milivoltmeter to TP8 (Lch) and CH2 of the millivoltmeter to TP9 (Rch).



4) At this time, adjust the attenuator until the TP8 and TP9 output levels become 210 mV.

5) Playback 1 kHz and check that the output level during playback and the output level during recording are within

±

2.5 dB.

6) Insert the test tape (TTA-615) into DECK 2, perform 3) to 5) and check that it is within

±

3 dB.

TP8

TP9

AC MILLIVOLTMETER

CH1 CH2

– 38 –


< TUNER SECTION >

1. Clock Frequency Check

Settings : • Test point : TP11 (CLK)

Method : Set to AM 1710 kHz and check that the test point is

2160 kHz

±

45 Hz.

2. AM VT Check

Settings : • Test point : TP10 (VT)

Method : Set to AM 1710 kHz and check that the test point is less than 8.5 V. Then set to AM 530 kHz and check that the test point is more than 0.6 V.

3. AM Tracking Adjustment

Settings : • Test point : TP14 (Lch), TP15 (Rch)

• Adjustment location : L951 (1/3)

Method : Set to AM 1000 kHz and adjust L951 (1/3) so that the test point becomes maximum.

4. FM VT Adjustment

Settings : • Test point : TP10 (VT)

• Adjustment location : L906

Method : Set to FM 108.0 MHz and adjust L906 so that the test point becomes 7.0 V

±

0.1 V. Then set to

FM 87.5 MHz and check that the test point is more than 0.4 V.

5. FM Tracking Adjustment



Method : Set to FM 87.5 MHz and adjust L903 so that the test point becomes maximum.

6. AM IF Adjustment


• Adjustment location :

L802 ................................................... 450 kHz

7. DC Balance / Mono Distortion Adjustment

Settings : • Test point : TP12, TP13 (DC balance)

TP18 (Lch), TP19 (Rch)

(Mono distortion)


• Input level : 60 dB

µ

V

Method : Set to FM 98.0 MHz and adjust L801 so that the voltage between TP12 and TP13 becomes

0 V

±

500 mV with distortion less than 0.5 %.

8. Output Level Check

<AM>



µ

V

Method : Set to AM 1000 kHz and check that the test point is

105 mV

±

3 dB.

<FM>



µ

V

Method : Set to FM 98.0 MHz and check that the test point is

420 mV

±

3 dB.

9. FM Separation Check

Settings: • Test point : TP14 (Lch), TP15 (Rch)


µ

V

Method: Set to FM 98.0 MHz and check that the test point is more than 25 dB.

< FRONT SECTION >

1.

µ

-CON Clock Adjustment

Settings : • Test point : TP17 (K-SCAN)

TP16 (GND)


Method : Insert AC plug while pressing of "POWER" key and

"CLOCK" function key. Connect a frequency counter across TP16 and TP17. Then adjust L901 so that the frequency across the test point is 226.98 Hz

±

0.23 Hz

(4.40 msec ~ 4.41 msec).

– 39 –


CD TEST MODE

1. How to Activate CD Test Mode

While pressing the FUNCTION button, insert the AC plug to the power outlet.

When the test mode is started, the message TEST is displayed.

2. How to Exit CD Test Mode

Press the POWER button, push other FUNCTION buttons or disconnect the AC plug.

3. Function Descriptions and Application of CD Test Mode

No Mode

1 Start Mode

Operation Display Function

All indicators All FL indicators light.

light.

2

3

4

5

6

Search Mode STOP button Reading LD illuminates all the time.

Focus-search continuous operations. *1

Spindle motor continuous kick.

Checking Item

FL check

Microprocessor check

APC circuit check

Laser current measurement

Focus-search waveform check

Focus-error waveform check

(DRF is ignored during search mode)

Each servo circuits is checked

DRF check

Play Mode PLAY button Normal Normal playback.

If TOC cannot be read, focus search is continued.

Traverse

Mode

Sled Mode

PAUSE button

FF button

RWD button

Normal

TEST

TEST

Tracking Servo OFF/ON.

Each time PAUSE button is pressed, the Tracking Servo repeats turning OFF/ON.

Tracking balance check

Pickup moves to the inner circumference. *2

Sled circuit check

Tracking circuit check

At the same time, the lens is kicked Mechanism operation check to the inner circumference.

Pickup check

Pickup moves to the outer circumference. *2

At the same time, the lens is kicked to the outer circumference.

Spindle Mode REC/REC All indicators The spindle motor rotates forward Spindle circuit check

MUTE button light.

(rough speed) by pressing the button and rotates backward by pressing one more time and stops by pressing again.

Spindle motor check

*1 : The driver IC heats up and the protection circuit starts working when the focus search is continued for 10 minutes or longer.

There can be a case where operations cannot be performed correctly.

In such a case, turn off the main power. After cooling down the machine, restart the machine.

*2 : Be careful not to damage the gear because the sled motor rotates while the FF or RWD button is pressed even when the pickup is located at the innermost track or the outermost track.

40


MECHANICAL EXPLODED VIEW 1 / 1

PLATE,SHILD SIDE

BZG-5 f

A

41

59

60 49

40

3

1

G

13

14

5

7

2

15

8

19

10

18 PWB

A

61

E e

43

16

17

A

I

20

21

22

FL

23

25

24

26

33

57

27

28

32

A

58 f

42

62

M

A

C

A

A

A a

34

A

A d

HT-SINK,FET

A

HT-SINK

44

A

A

PWB

46 e

J

PWB

45

A d

51

J

J

J

A

A

A

47

K

64

63

48

H

F

56

B

29 PWB

30 I

11 a

65

31

N

4

6

A

10

A

35

36

37

37

36

12

7

D

9

PLATE,EARTH MECH

39

38

2ZM-3MK2 all-guides.com

41

A

CHAS,MAIN b c

F

49 52

F

BINDER

WIRE

L c

PLATE,PT b

53

54

65

G

H

K

A

A

50

55

A

A


MECHANICAL PARTS LIST 1 / 1

REF. NO.

PART NO.

KANRI

NO.

DESCRIPTION

1 8B-NF6-008-010 WINDOW,CASS1

2 8B-NF6-009-010 WINDOW,CASS2

3 8B-NF6-003-010 BOX,CASS1

4 8B-NF6-004-010 BOX,CASS2

5 8A-NF8-281-010 SPR-T,EJECT 1

6 8A-NF8-282-010 SPR-T,EJECT 2

7 8B-NF6-021-010 KNOB,RTRY VOL

8 8B-NF6-027-010 KEY,ASSY ENTER

9 8B-NF6-029-010 KEY,ASSY MIC

10 8Z-NF6-210-010 DMPR,150 N

11 8B-NF6-011-010 PANEL,OPE

12 8B-NF6-041-010 CABI,FR H

13 8B-NF6-061-010 WINDOW,DISPLAY H

14 87-CE3-023-010 BADGE,AIWA 30N SILV

15 8B-NF6-010-010 PANEL,CD

16 8B-NF6-005-010 WINDOW,CD

17 8B-NF7-040-010 PANEL,TOP V-2 ANF8

18 8A-NF8-006-010 WINDOW,TOP

19 8B-NF6-034-010 PANEL,LEFT V-2

20 8B-NF6-012-010 KEY,POWER

21 8B-NF6-025-010 KEY,T-BASS

22 8B-NF6-017-010 KEY,CD

23 8B-NF6-024-010 REFLECTOR,CD

24 8B-NF6-022-010 REFLECTOR,FUN

25 8A-DB8-036-010 REFLECTOR,ECO

26 8B-NF6-211-010 GUIDE,FUN

27 8B-NF6-031-010 KEY,FUN

28 8B-NF6-032-010 KEY,OPE

29 8B-NF6-026-010 KEY,BBE

30 8B-NF6-018-010 KEY,SPICE

31 8B-NF6-019-010 KEY,EDIT

32 8B-NF6-212-010 GUIDE,CD

33 8A-NF6-201-010 GUIDE,FL

34 8B-NF6-217-010 HLDR,PWB FR

35 87-NF4-216-010 HLDR,LOCK 1

36 86-NF9-224-010 SPR-C,LOCK

37 82-NF5-229-010 PLATE,LOCK

38 87-NF4-217-110 HLDR,LOCK 2

39 8B-NF6-213-010 PLATE,EARTH MIC

40 8B-NF6-006-010 WINDOW,TRAY

REF. NO.

PART NO.

KANRI

NO.

DESCRIPTION

41 8B-NF6-002-010 PANEL,TRAY

42 8A-NF8-206-010 HLDR,PWB M

43 8B-NF6-206-010 HLDR,TR PNRM

44 8B-NF6-205-010 HLDR,TR AMP

45 8B-NF6-203-010 HLDR,HT-SINK F

46 8B-NF6-204-010 HLDR,HT-SINK R

47 8B-NF6-223-010 HLDR,DUCT

48 8B-NF6-214-010 HLDR,PWB PT

49 87-A91-751-010 FAN,DSB0812M-S382 -400MM

50 8B-NF6-052-010 CABI,REAR LHSM

51 8B-NF7-238-010 HLDR,FAN LOW

52 87-NF4-221-010 HLDR,CABLE

53 87-A80-092-010 AC CORD ASSY,E BLK SUN FAI

54 87-085-185-010 BUSHING, AC CORD (E)

55 8B-NF6-033-010 PANEL,RIGHT V-2

56 88-915-181-110 FF-CABLE,15P 1.25

57 88-905-061-110 FF-CABLE,5P 1.25 60MM

58 88-908-301-110 FF-CABLE,8P 1.25

59 88-909-141-110 FF-CABLE,9P 1.25 140MM

60 88-906-251-110 FF-CABLE,6P 1.25(RVS-FACE)

61 87-NF6-616-010 CONN ASSY,8P RPB

62 87-NF6-615-010 CONN ASSY,3P PB

63 8B-NF6-222-010 COVER,DUCT

64 8B-NF6-221-010 PLATE,DUCT L

65 87-064-185-010 HLDR,WIRE

A 87-067-703-010 TAPPING SCREW, BVT2+3-10

B 87-723-096-410 QT2+3-10W/O SLOT BL

C 87-721-096-410 QT2+3-10 W/O SLOT

D 87-067-688-010 BVTT+3-6

E 87-NF4-224-010 S-SCREW,IT3B+3-8 CU

F 87-067-579-010 TAPPING SCREW, BVT2+3-8

G 87-067-641-010 UTT2+3-8(W/O SLOT)BL

H 87-067-975-010 S-SCREW,IT+4-8

I 87-721-097-410 QT2+3-12 GLD

J 87-B10-315-010 BVIT3B+3-8 R W/O

K 87-078-200-010 S-SCREW,ITC+4-8 R

L 87-721-095-410 QT2+3-8 W/O SLOT

M 8B-NF6-220-010 W,3.5-8-0.5 W/ADH

N 87-591-095-410 QIT+3-8

COLOR NAME TABLE

Basic color symbol Color

B

G

LT

R

T

WT

LM

LD

YM

LA

Black

Green

Transparent Blue

Red

Brown

Transparent White

Metallic Blue

Dark Blue

Metallic Yellow

Aqua Blue

Basic color symbol

C

H

N

S

V

Y

LL

DT

DM

GL

Color

Cream

Gray

Gold

Silver

Violet

Yellow

Light Blue

Transparent Orange

Metallic Orange

Light Green

Basic color symbol

D

L

P

ST

W

YT

GT

GM

PT

HT

Color

Orange

Blue

Pink

Titan Silver

White

Transparent Yellow

Transparent Green

Metallic Green

Transparent Pink

Transparent Gray

42


TAPE MECHANISM EXPLODED VIEW 1 / 1

25

12

13

14

1

2

3

11

44 A

B

C

48

49

50

47

46

45

52

29

15

16

59

10

56

33

7

8

PLATE

SHLD,M3

60

4

5

6

PWB

27

38

31

32

58 b

29

30

60

E

38

31

35

29

58

37

39

43

51

40

43

37

32

29

35

30 a 36

57

23

33

25

D

23

18

20

19

24

7

GEAR,

PLAY

21

PWB

8

28

17

42

15

18

19

11

13

D

4

GEAR,

PLAY

5

6

PLATE

SHLD,M3

14

26

16 17

20

21

28

19

24

39

PWB

41

40

42

53

48

47 b

54 50

49

55

22

51

34

– 43 –

B

C

44

46

9

52

53

A a

54

55


TAPE MECHANISM PARTS LIST 1 / 1

REF. NO.

PART NO.

KANRI DESCRIPTION

NO.

1 82-ZM3-335-310 PULLEY,COUPLER M3

2 87-B10-043-010 W-P,0.99-4-0.25 SLT

3 86-ZM1-206-010 BELT,MAIN L

4 82-ZM1-322-010 SPR-T,FR 60

5 82-ZM1-220-210 GEAR,IDLER

6 82-ZM3-616-010 RING MAGNET 4

7 82-ZM3-348-010 LEVER ASSY,PINCH YL

8 82-ZM1-258-210 SPR-T,PINCH L

9 87-A91-195-110 HEAD,RPH KC9142 FPC

10 82-ZM3-342-010 BELT,SBU MOT 3

11 82-ZM1-338-110 BELT,FR 4

12 09-001-420-010 FLY-WHL,R ASSY

13 82-ZM3-333-310 SLIP DISK ASSY 2

14 82-ZM3-334-010 PW 2.16-6-0.4

15 82-ZM3-306-110 LVR,FR M2

16 82-ZM1-225-210 GEAR,FR

17 82-ZM3-305-310 GEAR,CAM M2(*)

18 82-ZM1-226-010 GEAR,REW

19 82-ZM1-216-510 GEAR,REEL

20 82-ZM1-227-310 LVR,TRIG

21 82-ZM1-265-310 SPR-E,TRIG

22 82-ZM3-351-010 HLDR,IC 2

23 82-ZM3-343-010 LEVER ASSY,PINCH YR

24 82-ZM1-259-210 SPR-T,PINCH R

25 82-ZM1-234-310 FLY-WHL,L ASSY

26 82-ZM1-237-610 FLY-WHL,R ASSY

27 82-ZM3-339-110 SHAFT,COUPLER N3

28 82-ZM1-255-310 SPR-E,LVR DIR

29 82-ZM1-217-410 REEL TABLE

30 82-ZM1-285-410 SPR-C,BT L

31 82-ZM1-333-210 PLATE,LINK2

32 82-ZM1-222-310 LVR,PLAY(*)

33 82-ZM3-307-010 CUSH-G,DIA3.7-8-3.2

34 87-045-347-010 MOT,SHU2L 70

35 82-ZM1-257-010 SPR-T,CAS

REF. NO.

PART NO.

KANRI DESCRIPTION

NO.

36 82-ZM3-340-010 SH,BELT D2

37 82-ZM1-242-010 LVR,CAS

38 82-ZM1-244-510 SPR-C,BT

39 82-ZM1-243-010 LVR,STOP

40 82-ZM1-240-110 LVR,REC(*)

41 82-ZM1-264-010 LVR,EJECT R

42 82-ZM3-62 7 0 10 SOL ASSY , 27 S O

43 82-ZM1-241-310 LVR,MC

44 82-ZM1-208-310 HLDR,HEAD

45 87-A91-196-110 HEAD,PH KP9142 FPC

46 82-ZM1-314-110 PLATE,HEAD

47 82-ZM1-207-910 GUIDE,TAPE

48 82-ZM3-353-010 SPR-T,HEAD 2

49 82-ZM1-210-110 GEAR,H T

50 82-ZM1-219-110 SPR-T,LINK

51 82-ZM1-269-210 SPR-T,BRG

52 82-ZM1-218-010 SPR-E,HB

53 82-ZM1-206-910 CHAS,HEAD

54 82-ZM1-266-310 LVR,DIR

55 82-ZM1-214-010 SPR-T,DIR

56 82-ZM3-221-210 PULLEY,MOT 2M

57 82-ZM3-301-610 CHAS ASSY,M2

58 80-ZM6-243-010 SH 1.75-3.6-0.5 SLT

59 82-ZM3-329-410 BELT,SBU R2

60 82-ZM1-288-010 SH,1.63-3.2-0.5 SLT

A 80-ZM6-207-010 V+1.6-7

B 86-ZM4-206-110 S-SCREW,AZIMUTH L

C 85-ZM3-202-010 S-SCREW,TG

D 82-ZM3-222-010 S-SCREW,SHILD PLATE

E 82-ZM3-318-110 S-SCREW W,MOTOR M2

– 44 –


GENERAL SPEAKER DISASSEMBLY INSTRUCTIONS (FOR REFERENCE)

Type.4

Type.1

Insert a flat-bladed screwdriver into the position indicated by the arrows and remove the panel. Remove the screws of each speaker unit and then remove the speaker units.

TOOLS

1 Plastic head hammer

2 ( ( ) flat head screwdriver

3 Cut chisel

Type.2

Remove the grill frame and four pieces of rubber caps by pulling out with a flat-bladed screwdriver. Remove the screws from hole where installed rubber caps. Insert a flat-bladed screwdriver into the position indicated by the arrows and remove the panel. Remove the screws of each speaker unit and then remove the speaker units.

1 2 3

How to Remove the PANEL, FR

1.

Insert the ( ( ) flat head screwdriver tip into the gap between the PANEL, FR and the PANEL, SPKR. Tap the head of the ( ( ) flat head screwdriver with the plastic hammer head, and create the clearance as shown in Fig-1.

2.

Insert the cut chisel in the clearance, and tap the head of the cut chisel with plastic hammer as shown in Fig-2, to remove the PANEL, FR.

3.

Place the speaker horizontally. Tap head of the cut chisel with plastic hammer as shown in Fig-3, and remove the

PANEL, FR completely.

Type.3

Insert a flat-bladed screwdriver into the position indicated by the arrows and remove the panel. Turn the speaker unit to counterclockwise direction while inserting a flat-bladed screwdriver into one of the hollows around speaker unit, and then remove the speaker unit. After replacing the speaker unit, install it turning to clockwise direction until "click" sound comes out.

Fig-1 Fig-2

Fig-3

How to Attach the PANEL, FR

Attach the PANEL, FR to the PANEL, SPKR. Tap the four corners of the PANEL, FR with the plastic hammer to fit the

PANEL, FR into the PANEL, SPKR completely.

– 45 –


SPEAKER PARTS LIST (SX-WNSZ900) <YLSL>

REF. NO.

PART NO.

KANRI DESCRIPTION

NO.

1 8B-NS6-001-010 PANEL,FR A

2 8B-NS7-002-010 PANEL,SP A

3 8B-NS7-003-010 PANEL,SP B

4 8B-NS7-005-010 PANEL,BA A

5 8B-NS7-004-010 PANEL,DUCT

6 8B-NS8-007-010 PROTECTOR,M

7 8B-NS6-604-010 SPKR,W 200 40/4

8 8B-NS7-604-010 SPKR,M 100W

9 88-NSK-610-010 SPKR,CERAMIC ASSY

10 88-NS5-610-010 CORD,SPKR

SPEAKER PARTS LIST (SX-S85) <YLSL>

REF. NO.

PART NO.

KANRI

NO.

DESCRIPTION

1 8B-NS7-009-010 PANEL,FR

2 8B-NS7-011-010 GRILLE,FRAME ASSY

3 8B-NS7-606-010 SPKR,80

4 8B-NS7-610-010 CORD,5.0

ACCESSORIES / PACKAGE LIST

REF. NO.

PART NO.

KANRI

NO.

DESCRIPTION

1 8B-NF6-902-010 IB,LH (ESP) M

2 8B-NF6-701-010 RC UNIT,RC-BAS04 all-guides.com

– 46 –


2000075 921338

2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111

Printed in Singapore

Aiwa NSX-SZ900 Service Manual

SERVICE MANUAL

COMPACT DISC

STEREO SYSTEM

BASIC TAPE MECHANISM : 2ZM-3MK2 PR7NM

BASIC CD MECHANISM : BZG-5 ZD3N1DM

SYSTEM SPEAKER

CD

CASSEIVER

REMOTE

CONTROLLER

SX-WNSZ900

NSX-SZ900 CX-NSZ900 RC-BAS04

SX-S85

• This Service Manual is the “Revision Publishing” and replaces “Simple Manual”

of CX-NSZ900 (LH), (S/M Code No. 09-013-444-1T1).

• If requiring information about the CD mechanism, see Service Manual of BZG-5,

(S/M Code No. 09-00C-353-3N2).

REVISION

SPECIFICATIONS

– 2 –

PROTECTION OF EYES FROM LASER BEAM DURING SERVICING

Precaution to replace Optical block

– 3 –

NOTE ON BEFORE STARTING REPAIR

1. Forced discharge of electrolytic capacitor of power supply block

2. Check items before exchanging the MICROCOMPUTER

– 4 –

– 5 –

ELECTRICAL MAIN PARTS LIST

– 6 –

– 7 –

– 8 –

– 9 –

– 10 –

Chip resistor

Chip Resistor Part Coding

Resistor Code

Figure

Value of resistor

– 11 –

TRANSISTOR ILLUSTRATION

– 12 –

IC DESCRIPTION

– 34 –

– 35 –

ADJUSTMENT < DECK / TUNER / FRONT >

– 36 –

– 37 –

– 38 –

– 39 –

CD TEST MODE





MECHANICAL PARTS LIST 1 / 1

COLOR NAME TABLE





TAPE MECHANISM PARTS LIST 1 / 1

– 44 –

GENERAL SPEAKER DISASSEMBLY INSTRUCTIONS (FOR REFERENCE)

How to Remove the PANEL, FR

How to Attach the PANEL, FR

– 45 –

SPEAKER PARTS LIST (SX-WNSZ900) <YLSL>

SPEAKER PARTS LIST (SX-S85) <YLSL>

ACCESSORIES / PACKAGE LIST

– 46 –

2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111

Key Features

Related manuals

Aiwa

NSX-SZ900

Aiwa

Z-L620 LH

Aiwa

XH-DT7

Aiwa

Z-L620

Aiwa