advertisement
iR����-S� 快速安裝導引
A
A
B
C
LED 指示燈
硬碟抽取盒把手
頂出按鍵
B
前視圖
C D
E
F
D
E
F
硬碟抽取盒鎖
靜音按鈕
SATA ��Pin 電源輸入埠
背視圖
G
G
H
H
SATA 連結埠
RAID 模式設定
打開包裝外盒後，包裝內容英包含下列組件： iR����-S� 主體 x� 快速安裝導引 x� 螺絲及鑰匙
˙
˙
請先確認相關配件與產品本身是否有受損或是缺少配件，若有任何疑問，請與您的經
銷商或業務人員聯絡。
請前往官網 (www.raidon.com.tw) 下載說明書、驅動程式以及其餘相關資源。
狀態
硬碟閒置
資料存取
無硬碟 / 硬碟故障
資料重建 - 來源碟
資料重建 - 目標碟
溫度過高 ( ≧ 50 度 )
硬碟狀態燈
藍燈恆亮
紫燈閃爍
紅燈恆亮
藍燈恆亮
紅燈閃爍
藍燈恆亮
蜂鳴器
N/A
N/A
鳴叫
N/A
N/A
鳴叫
請參照下列步驟，完成 iR����-S� 的硬體安裝:
�.
在背板上的 RAID 模式設定中以跳線設定 RAID 模式，原廠預設值為 RAID �。
�.
將主體裝置在機殼上，連接相關連接線，並確認固定螺絲是否鎖上。
RAID � 模式 RAID � 模式
銳銨科技
V1.0 (Aug. 2020)
※ 螺絲孔位說明
�.
使用配件內附的鑰匙解鎖硬碟抽取盒鎖後，將頂出按鍵向右推移，硬碟抽取盒把手便會彈
開，即可取出抽取盒。
�.
在抽取盒上安裝 �.� 吋硬碟，請使用 � 顆零件包內附的小顆螺絲加以固定；再將抽取盒裝回 iR����-S�。
�. 若想得到較佳的使用效能與選購硬碟的便利性，建議使用規格及廠牌相同的 �.� 吋硬碟。若
RAID � 模式下，當其中有任何一顆硬碟毀損時，新更換的硬碟容量需大於或等於原硬碟
容量。
�. 請確保使用的硬碟是不含壞軌的，以避免當其中一顆硬碟發生故障時，可能導致系統當機或
所有資料遺失。
�. 建議於使用前決定 RAID � 或 RAID � 模式。使用後，若需再重新設定，請先將資料備份至其
他硬碟，否則將會造成硬碟內的資料損毀。
�. 在新增或變更 RAID 模式後需重新啟動，以確保完成更新為新的 RAID 模式。
�. 強烈建議除了使用 iR����-S� 的資料儲存功能外，請針對重要資料備份到另一個儲存裝置
上或遠端備份，雙重備份您重要的資料。若您儲存在 iR����-S� 的資料損毀或遺失，
RADION 將不負任何的責任。
與 �.�" 硬碟
螺絲孔位相同
與軟碟機螺絲孔位相同
感謝您使用 銳銨科技股份有限公司 的產品。
本手冊裡的資訊在出版前雖然已經被詳細確認，但實際產品規格將已出貨時為準；任何的產品
規格或相關資訊更新，請您直接上 www.RAIDON.com.tw
網站查詢，或直接與您的業務聯絡
窗口聯繫，本公司將不另行通知。
如果您對 銳銨科技 的產品有任何疑問，或是想獲得最新產品訊息、使用手冊或韌體，請您聯絡 [email protected]
，我們將儘速回覆您。
RAIDON 為 銳銨科技股份有限公司 旗下品牌之一
本說明相關產品內容歸 銳銨科技股份有限公司 版權所有
�.
�.
硬體安裝完成。您可開啟電源進行相關設定與應用。
完成。你的作業系統將會自行辨識硬體，辨識成功後請先完成硬碟格式化，完成後即可
使用。
iR����-S� Quick Installation Guide
A
Product Diagrams and Contents of Product Package
Front View
B
C D
E
F
Rear View
G
H
A
B
C
LED Indicator
Removable drive tray
HDD Tray Ejection
D
E
F
HDD tray key lock
Mute Button
�� PIN Power Connector
G
H
SATA Port
RAID Switch
After you open the outer package, make sure that the following items are contained in the package: iR����-S� body x� Quick Guide x1 Screws and key
˙
˙
Please check the product and accessories for any defect or missing parts. If you have any questions, please contact your product supplier.
Please visit the official website (www.raidon.com.tw) to download user manuals, drivers and other related resources.
LED Instruction
Constant
HDD Idle
Data access
No hard drive / hard drive failure
Rebuilding - Source
Rebuilding - Target
Over Temp ( ≧ 50 ℃ )
HDD Status Light
Blue light always on
Purple light flashing
Red light always on
Blue light always on
Red light flashing
Blue light always on
Buzzer
N/A
N/A
ON
N/A
N/A
ON
Hardware Installation
Please install iR����-S� as the following instruction.
�.
�.
The RAID mode is set by jumper in the RAID mode switch on the backplane. The default value is RAID �.
Install the product unit into the comput er chassis and make the necessary connections and mount the product unit properly and securely to the bay position desired.
RAID � Mode RAID � Mode
Raidon
V1.0 (Aug. 2020)
※ Mounting Positions
�.
After unlocking the HDD tray key lock with the key attached to the accessory, push the HDD tray ejection to the right and the removable drive tray will pop open to remove the removable tray.
�. For �.�" HDD/SSD, please secure it by use four the smaller screws included in the accessory kit. and re-insert the removable tray when completed.
Screw positions to mount like a
3.5" hard drive
Screw positions to mount like a floppy drive
Precautions Before Application
1.
2.
3.
4
5.
We suggest you using 2 brand new 2.5-inch SATA hard drives with the same brand and model number for the best performance. When any one of the hard drives is failed, please ensure that the capacity of the new hard drive is the same or bigger than the original one.
Please ensure that the hard drives are free of bad tracks before using, otherwise, it may cause system crash in turn resulting in data loss.
We strongly suggest you that the RAID mode should be decided before starting use iR2775-S3+. If you need to reset the RAID mode after using iR2775-S3, please remember to backup your data on the other hard drives or the data may lose.
A reboot is required after adding or changing RAID mode to ensure that the update is completed to the new RAID mode.
We strongly recommend you to keep an extra copy at your important personal data other than stored in your iR2775-S3 product. RAIDON will not be responsible of your data loss problem.
Thank you for choosing RAIDON’s product.
The information provided in this manual was checked before publication, but the actual product specifications may have changed before shipping; Latest product specifications and updates can be found at www.RAIDON.com.tw or through your sales representative. No separate notifications will be provided by our company.
If you have any questions about RAIDON products or would like to receive the latest product information, instruction manuals, or firmware, please contact S [email protected] for assistance.
RAIDON is one brand under RAIDON TECHNOLOGY, INC.
All product-related content in this manual are copyrighted by RAIDON TECHNOLOGY, INC.
�.
When hardware installation is completed, you can turn on the power of the main unit to proceed with relevant settings and applications.
�.
Installation completed. Your operating system should automatically detect the hard drives within. Please proceed to format the drives. Once formatting is completed, you may then start to operate the device.
advertisement
Related manuals
advertisement