Comelit 40861 Manual

COLOR CCD, AUTOFOCUS, DAY & NIGHT,

ZOOM CAMERA

ART.40861

Please read this manual thoroughly before use and keep it for future reference.

Via Don Arrigoni, 5 24020 Rovetta S. Lorenzo (Bergamo) http://www.comelit.it – E mail: [email protected]

ISSUE 3 - OCTOBER 2007

LIMITATION OF LIABILITY

THE INFORMATION IN THIS PUBLICATION IS BELIEVED TO BE ACCURATE IN ALL

RESPECTS, HOWEVER, WE CANNOT ASSUME RESPONSIBILITY FOR ANY

CONSEQUENCES RESULTING FROM THE USE THEREOF. THE INFORMATION

CONTAINED HEREIN IS SUBJECT TO CHANGE WITHOUT NOTICE. REVISIONS OR

NEW EDITIONS TO THIS PUBLICATION MAY BE ISSUED TO INCORPORATE SUCH

CHANGES.

WARNINGS AND CAUTIONS:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR

MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR

OTHER OPENINGS ON THE EQUIPMENT.

CAUTION:

CAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER(OR BACK). NO

USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

PRECAUTIONS

Safety ----------------------------------------- Installation -----------------------------------

Should any liquid or solid object fall into the cabinet, unplug the unit and have it checked by the qualified personnel before operating it any further.

Unplug the unit from the wall oulet if it is not going to be used for several days or more. To disconnect the cord, pull it out by the plug. Never pull the cord itself.

Allow adequate air circulation to prevent internal heat build-up. Do not place the unit on surfaces (rugs, blankets, etc.) or near materials(curtains, draperies) that may block the ventilation holes.

Do not install the unit in an extremely hot or humid place or in a place subject to excessive dust, mechanical vibration.

The unit is not designed to be waterproof.

Exposure to rain or water may damage the unit.

Cleaning --------------------------------------

Height and vertical linearity controls located at the rear panel are for special adjustments by qualified personnel only.

Clean the unit with a slightly damp soft cloth.

Use a mild household detergent. Never use strong solvents such as thinner or benzine as they might damage the finish of the unit.

Retain the original carton and packing materials for safe transport of this unit in the future.

FCC COMPLIANCE STATEMENT

FCC INFORMATION :

THIS EQUIPMENT HAS BEEN TESTED

AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL

DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE

LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION

AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS

OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT

GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY

ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH

THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE

TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN

A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL

INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO

CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.

CAUTION :

CHANGES OR MODIFICATIONS NOT EXPRESSLY

APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE

COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.

THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN

ICES-003.

NORME NMB-003 DU CANADA.

CE COMPLIANCE STATEMENT

WARNING

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

- 1 -

IMPORTANT SAFEGUARDS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that product heat..

9. Do not defeat the safety purpose of the polarized or grounding-type

Plug. A polarized plug has two blades with one wider than the other.

A grounding type plug has two blades and a third grounding prong.

The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where thy exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Unplug this apparatus during lightning storms or when unused for long periods of time.

13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

14. CAUTION - THESE SERVICING INSTRUCTIONS ARE FOR USE

BY QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE

RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING

OTHER THAN THAT CONTAINED IN THE OPERATING

INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO.

15. Use Certified/Listed Class 2 power supply transformer only.

- 2 -

THIS PAGE INTENTIONALLY LEFT BLANK.

- 3 -

TABLE OF CONTENTS

1. INTRODUCTION

1.1 THE CAMERA FEATURES

2. SYSTEM INSTALLATION

2.1 PACKAGE CONTENTS

2.2 OPERATION REQUIREMENTS

3. PARTS NAME & FUNCTION

4. CONNECTION

4.1 COLOR LEAD WIRE & COLOR DISPLAY LABEL

4.2 EXTERNAL DAY/NIGHT CONTROL

4.3 RS-485 CONNECTION

4.4 EXTERNAL LENS CONTROL

4.5 EXTERNAL A/D KEY CONTROL

5. CAMERA ADJUSTMENT

5.1 OSD MAIN SCREEN

5.2 MAIN MENU

6. TROUBLESHOOTING AND MAINTENANCE

6.1 TROUBLESHOOTING

6.2 MAINTENANCE

7. SPECIFICATIONS

8. DIMENSIONS

8

9

15

15

15

16

17

6

7

8

5

6

6

2

2

3

5

1

1

2

- 4 -

1

Introduction

The Day & Night AutoFocus Zoom color DSP Camera is designed especially for closed circuit television (CCTV) and security surveillance applications.

1.1 THE CAMERA FEATURES

High performance SONY 1/4" Super HAD CCD

242x zooming capability (Optical : 22x / Digital : 11x)

Ultra Sensitivity Minimum illumination of 0.001 lux @F1.6 (low shutter)

Excellent picture quality

Various picture effects

Support camera control available RS-485

Flexible configuration

DC 12V input

(CAUTION : Use Certified/Listed Class 2 power supply transformer only.)

Function : - D/N (Day / Night) - Low-SHUT (Digital Slow shutter)

- DIS (Digital Image Stabilize) - WDR (Wide Dynamic Range)

- DNR (Digital Noise Reduction) - AWB (Auto White Balance)

- AE (Auto Exposure) - AGC (Auto Gain Control)

- BLC (Back Light Compensation) - OSD (On Screen Display)

- D-Zoom (Digital Zoom) - NEGA/POSI (Negative / Positive)

- B/W (Black / White) - PIP (Picture In Picture)

- FREEZE (Rear & still picture) - MIRROR (Right, left reverse picture)

IMPORTANT : The user of this camera is responsible for checking and complying with local, state, and federal laws and statutes concerning the recording and monitoring of audio signals.

1

2

System Installation

Installation of the camera must be performed by qualified service personnel in accordance with all local national electrical and mechanical codes.

Perform the following steps to install the camera.

2.1 PACKAGE CONTENTS

Camera

Instruction Manual

12 pin interface cable

A/D Remote Controller (option)

2.2 OPERATION REQUIREMENTS

< Typical System Configuration >

2

3

Parts Name & Function

Carefully remove the contents from the box, and verity that nothing was damaged in shipment.

4 Point - Drilling Position

502162 3A

1 – Day & Night Zoom lens

Integrated lens with 22x optical and 11x digital zoom

2 – Filter mount

Accepts commonly used filters with 37mm diameter

3 – Front case

4 – Mounting adapter

Is used to mount the camera onto a bracket

5 – Case body

6 – Rear case

7 – Camera module

8 – Connector for control interface

12 pin connector

PIN Description

485-

RS-485(-)

TX RS-232 TXD IN

EXT-OUT External Out

EXT-IN External In

AD1 A/D KEY 1

COM Common

Description PIN

RS-485(+)

485+

RS-232 RXD IN RX

Ground GND

A/D KEY 2 AD2

Far (-), Near (+) FOCUS

Tele (-), Wide (+) ZOOM

3

9 – Tele/Wide button

Zoom control: push Wide for wide angle views or Tele to zoom in

10 – Menu button

Menu functions in the OSD display can be controlled when the

OSD menu is activated

11 – Near/Far button

Press the Near side to focus on near objects or the Far side to

Focus on far objects. Focus button are activated in AF off mode

12 – BNC connector

It connects the camera and the monitor or ect.

13 – Power input terminal

Receive DC 12V from the power supply

14 – Power indicator

Is lit when the power is supplied

4

4

Connection

CAUTION : Do not connect the power cable until all other connections have been completed. If you complete the whole connection of cameras, then you have to cut the extra cable.

4.1 COLOR LEAD WIRE & COLOR DISPLAY LABEL

5

4.2 EXTERNAL DAY/NIGHT CONTROL

Connect to an external sensor to receive day/night detection signals.

DAY/NIGHT External sensor switch ON/OFF

GND

(RED)

EXT-IN

DAY : OPEN

NIGHT : CLOSED

COLOR mode: 0V output

EXT-OUT

EXT-IN

(GRAY)

EXT-OUT

(WHITE)

*Note: To validate the sensor inputs, select menu Effect - B/W - EXT

4.3 RS-485 CONNECTION

B/W mode: 5V output

Connecting to the RS-485 : the camera can be controlled remotely by an external device or control system, such as a control keyboard, using RS-485 half-duplex. Connect marked Rx+, Rx- to Tx+ and Tx- of the RS-485 control system.

RS-485

4.4 EXTERNAL LENS CONTROL

FOCUS

RS-485(-)

(PINK)

RS-485(+)

(BLACK)

FOCUS

(YELLOW)

COMMON

(BLUE)

FOCUS

NEAR(+) : External Power DC ±3V to ±12V (YELLOW)

: GND (BLUE)

FAR(-) : GND (YELLOW)

: External Power DC ±3V to ±12V BNC (BLUE)

ZOOM

COMMON

(BLUE)

ZOOM

(GREEN)

ZOOM

TELE(+) :

External DC ±3V to ±12V (GREEN)

:

GND (BLUE)

WIDE(-) : GND (GREEN)

: External DC 3V to 12V (BLUE)

6

4.5 EXTERNAL A/D KEY CONTROL

External Controller Circuit Schematic

7

5

Camera Adjustment

5.1 OSD MAIN SCREEN

AF 22X

AEAUTO

AWB

MF

NORMAL

F1.6

0DB

84X CAM 01

Camera title

Status of the auto exposure

Status of the auto white balance

Status of the focus mode

Status of the zoom position, brightness, or sharpness

Status of the shutter speed

Status of the iris

Status of the AGC (auto gain control)

Camera ID

8

5.2 MAIN MENU

<MAIN MENU>

WB

AE

BLC

TITLE

DISPLAY/ALARM

CAM SET

EFFECT

PRESET

END

5.2.1 WB (White Balance)

<WB>

AWB

INDOOR

OUTDOOR

MANUAL R/B

WAWB

END

5

6

7

8

1

2

3

4

AWB Auto white balance mode.

INDOOR Indoor white balance mode.

OUTDOOR Outdoor white balance mode.

MANUAL Manual mode. You can change R and B Gain manually.

For changing R and B gain, use "NEAR" and "FAR" key.

WAWB

If you save the change, and push the "MENU" key.

Wide range auto white balance mode.

9

5.2.2 AE (Auto Exposure)

<WE>

AUTO

IRIS PRI

SHUTTER PRI

AGC

MANUAL

IRIS

AGC

SHUT

LOWSHUT

END

AUTO

IRIS PRI

SHUTTER PRI

AGC

MANUAL

LOW-SHUT

Auto exposure mode (Iris, Shutter, AGC)

Iris priority auto exposure mode.

Shutter priority auto exposure mode.

Auto gain control on/off.

Manual exposure mode (Iris, Shutter, AGC)

Display Low-Shutter mode (Mode can be changed in the

Preset menu)

5.2.3 BLC (Back Light Compensation)

<BLC>

DEFAULT

ADJ TOP

ADJ BOTTOM

LEVEL

OFF

END

DEFAULT

ADJ TOP

ADJ BOTTOM

LEVEL

OFF

Default setting. Center weight BLC.

You can adjust BLC zone in left and/or top direction.

You can adjust BLC zone in right and/or bottom direction.

You can adjust BLC level (0 ~ +90)

Default value is 30.

BLC off.

10

5.2.4 TITLE

A TITLE

<TITLE MENU>

B

C CMD

A. TITLE

B. Character Table

C. Command Line

: Move to left

: Move to right

< : Erase a left character

> : Erase a right character

S : Save title

E : End

5.2.5 DISPLAY/ALARM

<DISPLAY/ALARM>

DISP0

DISP1

DISP2

DISP PUSHON

ALARM MODE

DWELL TIME

END

DISP0

DISP1

DISP2

DISP

ALARM MODE

DWELL TIME

Display title and camera ID.

Display title, camera ID and zoom lens position.

Display all camera status.

Off, On and push on (Display on when any key is pressed)

Off, Preset 1~5, B/W (Zoom preset and B/W setup by external-in)

10, 20,....120sec. (Dwell time setup of zoom preset)

11

5.2.6 CAM SET

<CAM SET>

ID

BPS

BRIGHTNESS

SHARPNESS

DISTANCE

MAX LOW SHUT

PROTOCOL

SAVE PROTOCOL & BPS

END

ID

BPS

Select the camera ID (1 ~ 255)

Select serial communication speed

(2400 / 4800 / 9600 / 19200)

BRIGHTNESS Select brightness level (0 ~ +90)

Default value is 30.

Select sharpness level (0 ~ 15) SHARPNESS

DISTANCE

Default value is 8.

Select minimum distance in focus between camera and object. (0.1 / 1.0 / 1.5 / 2.5 / 6.0 m)

MAX LOWSHUT

PROTOCOL

Select maximum Low-shutter value

(x2, x4, x8, x16, x32, x60)

Select operating protocol.

COMMAND : Camera controlled by RS-232C command.

FASTRAX : Fastrax protocol.

PELCO-D : Pelco-D protocol.

PELCO-P : Pelco-P protocol.

SAVE PROTOCOL & BPS Save protocol and BPS.

*NOTE 1 : You can choose BPS menu appropriate for keyboard protocol.

*NOTE 2 : If you change BPS or PROTOCOL menu, you have to select

PROTOCOL & BPS menu.

Although you change BPS or PROTOCOL menu, the terms of change is not applied unless you select SAVE PROTOCOL & BPS menu.

12

5.2.7 EFFECT

<EFFECT>

D-ZOOM

NEGA/POSI

B/W

MIRROR

PIP

FREEZE

D/N

DNR

END

D-ZOOM

NEGA/POGI

B/W

MIRROR

PIP

FREEZE

D/N

DNR

Digital Zoom on/off.

Select the Negative or Positive picture.

Select Color & B/W picture or EXT mode.

Select horizontal reverse picture.

Picture In Picture on/off.

Select real and still picture.

Day & Night mode on/off

Digital noise reduction mode on/off

CAUTION : Freeze mode is automatically off during zoom and focus operation.

13

5.2.8 PRESET

<PRESET>

FOCUS

SYNC

INIT

LOAD

SAVE

SHOT

ZOOM PRESET

SET ZOOM PRESET

END

FOCUS

SYNC

INIT

LOAD

SAVE

SHOT

Select auto, manual, pushauto mode.

Select internal or line lock mode.

Sync phase is adjustable in line lock mode.

Camera initialize mode selection(DEFAULT / PRESET).

Load default or preset parameters of camera

(DEFAULT / PRESET).

Save preset camera parameters.

Select Normal, DIS, WDR, or Low-Shutter mode.

DIS(digital image stabilization)

WDR(wide dynamic range)

ZOOM PRESET

Low-Shutter(low shutter speed mode)

Select zoom preset number

SET ZOOM PRESET You can set zoom position of zoom preset

CAUTION : In the WDR or Low-Shutter mode, AF performance and Image

quality can be decrease.

DIS is operated on D-Zoom X 2.

DNR is disabled in Freeze, Low-Shutter and WDR mode.

WDR is not effective in freeze status.

14

6

Troubleshooting and Maintenance

6.1 TROUBLESHOOTING

If problems occur, verify the installation of the camera with the instruction in this manual and with other operating equipment.

Isolate the problem to the specific piece of equipment in the system and refer to the equipment manual for further information.

PROBLEM POSSIBLE SOLUTION

Nothing appears on the screen

Are the power cord and line connection between the camera and monitor made properly?

The image on the screen is dim.

The camera is not working properly and the surface of the camera case is hot.

Is the lens dirty?

If so, clean the lens with a soft, clean cloth.

Is the camera connected to the proper power?

The contrast on the screen is too weak.

Adjust the contrast feature of the monitor.

Is the camera exposed to strong light?

If so, change the camera position.

6.2 MAINTENANCE

Preventive maintenance allows detection and correction of minor faults before they become serious and cause equipment failure.

Every three-month, perform the following maintenance.

A. Inspect all connection cables for deterioration or other damage.

B. Clean components with a clean damp cloth.

C. Verify that all the mounting hardware is secure.

15

7

Specifications

POWER

GENERAL

&

ETC.

CONNECTOR

F

C

T

O

Auto Exposure

Iris Control

AGC

Shutter Speed

BLC

Title

Display

CAM ID

BPS

Brightness

Sharpness

Distance

Low Shutter

Effect

Preset

SHOT

L

E

Zoom Ratio

Focus Length

N

S Aperture Ratio

Power Input

Video Output

Operating Temperature

Operating Humidity

Storage Temperature

External Dimensions

Weight

MODEL

Power Source

Power Consumption

Image Sensor

Total Pixels

Scanning System

U

N

I

N

NTSC

811(H) x 508(V)

DC 12V

5.5 Watts

1/4" SONY Super HAD CCD

2:1 interlace

PAL

Scanning Frequency 15,734KHz(H), 59,94Hz(V) 15,625KHz(H), 50Hz(V)

Sync. System

Resolution

Min. illumination

Video Output

S/N Ratio

Camera Control

Focus Mode

White Balance

795(H) x 596(V)

Internal / External (Linelock)

480 TV lines(Color), 530 TV lines(B/W)

0.5 lux(Color), 0.05 lux(B/W), 0.001 lux(Low-shutter)

1.0 Vp-p (75 ohm, composite)

52dB (AGC off)

RS232, RS485(Fastraxll, Pelco D, Pelco P), A/D key

Auto / Manual / Push AF

AWB / Indoor / Outdoor / Manual / WAWB

Auto / Iris PRI / Shutter PRI / AGC / Manual

Auto / Manual (F1.6 ~ F32)

On / Off (30dB max.)

Normal ~ 1/10,000

Default / ADJ Top / ADJ Bottom / Level / Off

A ~ Z / 0 ~9

On / Off / Push On (DISP0 / DISP1 / DISP2)

001 ~ 255

2400 / 4800 / 9600 / 19200

0 ~ 90 steps

0 ~ 15 steps

0.1M / 1.0M / 1.5M / 2.5M / 6.0M

x2 ~ x60

D&N, D-Zoom, Nega/Posi, B/W, Mirror, PIP, Freeze, DNR

INIT / LOAD / SAVE

Normal / DIS / WDR / Low-shutter

Optical x22, Digital x11 Zoom (Video AF) f = 3.9 mm ~ 85.8 mm

F1.6 (wide) ~ F3.7 (tele)

3-pin terminal block

BNC connector

-10 o

C ~ +50 o

C

0 ~ 96% (non-condencing)

-20 o

C ~ +60 o

C

62(W) x 62(H) x 105(D) mm

315 g

16

8

Dimensions

Via Don Arrigoni, 5 24020 Rovetta S. Lorenzo (Bergamo) http://www.comelit.it – E mail: [email protected]