Installation Instructions

TELEHOOK

12/30 Multi

Component Checklist

Swing Arm Components

Secondary Arm

200mm (x1)

Swing Arm

(x1)

Yoke (x1) 75/100mm VESA

Plate (x1)

Cover

Plate (x1)

Wall

Bracket (x1)

M8 Cap Screw (x1)

One Sided

Bush (x4)

Primary Arm 230mm (x1)

M8 Square

Neck Bolt (x2) M8 Nyloc’s (x2)

200mm VESA

Plate (x1)

Bits Box

14 Gauge Coach Screws (x2) 6mm Allen Key (x1) Double Sided

Bush (x1)

Push In Clips (x3)

Steel

Washers (x2)

Plastic

Washers (x2)

M6 x 12mm

Screws (x6)

M8x 115mm Bolt (x1)

Installation Procedure

4mm Allen Key (x1) M8 Nyloc (x1) Nylon Anchor Plugs (x2)

M4 x 10mm

Screws (x6)

!

!

! IMPORTANT - Install Telehook Multi as per Installation Instructions.

Telehook Multi supports Displays from 12” (30cm) to 30” (76cm) weighing up to 18kg (39lbs).

The Manufacturer accepts no responsibility for incorrect installation.

A Check Components

M4 x 12mm

Screws (x6)

Check you have received all parts against the Component Checklist and Bit Bag above.

B Choose your Mounting Option

Select which mounting option is best suited for your application.

Note that the Telehook 12-30 Multi comes packaged as the Swing Arm by default. (Option 1.)

M4 x 16mm

Screws (x6)

Option 1: Swing Arm

ISOMETRIC VIEW

Option 2: Articulated Arm

Wall

Option 3: Wall Mount

Follow Steps; C, E, F, & J

Horizontal Correction of Display

If the display does not sit horizontally, loosen the screw shown on the back of the yoke using the 4mm

Allen Key.

Re-tighten screw firmly when display is positioned horizontal.

Adjust Angle

Loosen

Screw

4mm Allen Key

Wall

Follow Steps; G, H, I, & J

Options 1 & 2 (Swing Arm & Articulated Arm)

C Installing the Wall Bracket

NOTE! You must remove the Wall Bracket from the Swing Arm before Installing

C.1 Mounting to a timber stud wall

- Position Wall Bracket vertically on the wall and mark the 2 mounting holes. (Use a Spirit Level)

- Drill 2x50mm(2”) holes using a 3mm(3/16”) drill bit.

- Secure the Wall Bracket using the supplied 14 Gauge Coach

Screws.

- Attach the Cover Plate as shown in diagram C.1.

C.2 Mounting to a masonry wall

- Position the Wall Bracket vertically on the wall and mark the 2 mounting holes. (Use a Spirit Level)

- Drill holes using an 8mm masonry drill bit.

- Secure the Wall Bracket using the supplied 14 Gauge Coach

Screws and Nylon Anchor Plugs.

- Attach the Cover Plate as shown in diagram C.2.

C.1.

Wall Bracket

C.2.

Wall Bracket

Cover Plate Cover Plate

Stud

2x Nylon

Anchor Plugs

Masonry Wall

2x14 Gauge

Coach Screws

Wall Follow Steps; C, D, F & J

Wall

Material

2x14 Gauge

Coach Screws

D Swing Arm Assembly

D.1.

Assemble the Swing Arm as

Illustrated.

- Select the appropriate VESA plate (75/100mm or 200mm) to suit your display.

- Connect VESA Plate as shown and tighten M8 Cap Screw.

- Adjust Display Tilt when fitted.

(Refer to diagram F.2)

- Install Push-In Clips for cable management.

M8 Nyloc (x2)

One Sided

Bush (x4)

M8 Square

Neck Bolt (x2)

E Articulated Arm Assembly

E.1.

Assemble the Articulated Arm as Illustrated.

M8 Nyloc (x3)

- Select the appropriate VESA plate (75/100mm or 200mm) to suit your display.

Plastic

Washer (x2)

Steel

Washer (x2)

- Connect VESA Plate as shown and tighten M8 Cap Screw.

- Adjust Display Tilt when fitted.

(Refer to diagram F.2)

- Install Push-In Clips for cable management.

Primary

Arm

Push-In

Clips (x3)

M8 Cap Screw

Primary Arm

Push-In

Secondary Arm

Yoke

Clips (x3)

M8 Cap

Screw

Yoke

6mm Allen Key

OR

75/100mm

VESA Plate

200mm

VESA Plate

6mm Allen Key

OR

200mm

VESA Plate

75/100mm

VESA Plate

One Sided

Bush (x4)

M8x115mm

Bolt M8 Square

Neck Bolt (x2)

F Connect your Display

Note: It is recommended that at least two people carry out this operation.

F.1. Attach your Display using the provided M4 Screws.

F.2. Tighten the Yoke connection to suit the weight of your display.

6mm Allen Key

4xM4

Screws

75 or 100

Option 3 (Wall Mount)

Note: You will require an extendable socket wrench during installation.

G Attach the VESA Plate to your Display.

Select the appropriate VESA plate (75/100mm or 200mm) to suit your display, and connect as shown.

G.1.

M4 Screws (x4)

G.2.

200mm VESA

Plate

75 or 100 or

M4 Screws

(x6)

H Install the Wall Bracket I Attach your Display

Note: It is recommended that at least two people carry out this operation.

H.1. Optional Stud

Mounting holes

Wall Bracket

Cover Plate

I.1.

Attach your Display as shown.

M8 Square

Neck Bolt

2x14 Gauge

Coach Screws

(Choose which

Mounting Holes)

Using an extendable

Socket Wrench, firmly tighten the connection to suit the weight of your display.

Push-In Clip

Install The Mount Bracket Horizontally as shown.(Use Spirit

Level) Use optional stud mounting holes for mounting to a single stud. Refer to Step C. for further detailed wall fixing instructions.

M8 Nyloc

Your Telehook Wall Mount is now complete. See Step J for installing Cable Management.

J Installing Cable Management

J1

Ensure Push In Clips have been fitted. Note; They can be used in either the top or the bottom face of each Arm and the Cover Plate.

J2

Your Telehook Articulated Arm or Swing Arm is now complete. See Step J for installing Cable Management.

Attach Cables to the Telehook Multi using the Push In

Clips

Your Telehook Multi is now complete and ready to use.

As TFT Manufacturers are constantly releasing new monitor models, Atdec does not accept responsibility if the VESA mounting does not comply with the international standards. Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 01.09.05

c