EverFocus EQ700 User`s manual
Add to My manuals12 Pages
EverFocus EQ700 is a box camera equipped with a 1/3” 960H SONY Exview HAD CCD II sensor, capable of producing ultra high-resolution images with 720TVL resolution. It boasts exceptional low-light sensitivity of 0.0001 lux, delivering clear images even in near-darkness. The camera features 2D Noise Reduction for improved picture clarity and efficient disk storage utilization on DVRs. With a full suite of OSD menu options accessible via built-in control buttons, you can fine-tune various image settings.
advertisement
EQ700 Ultra 720+ Series
True Day/Night Box Camera
User’s Manual
Copyright © EverFocus Electronics Corp,
Release Date: January, 2014
** Lens not included.
Precautions
Please read this manual first to ensure correct installation and operation. This manual should be retained for future reference. The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without notice.
1. Do not install the camera near electric or magnetic fields.
Install the camera away from TV / radio transmitters, magnets, electric motors, transformers and audio speakers, because the electromagnetic fields generated by these devices may distort the video image or otherwise interfere with camera functions.
2. Never disassemble the camera beyond the recommendations in this manual, nor apply materials to it other than those recommended herein.
Improper disassembly or introduction of corrosive materials may result in equipment failure or other damage.
3. Try to avoid pointing the camera toward the sun.
In some circumstances, direct sunlight may cause permanent damage to the sensor and / or internal circuits. It may also create unbalanced illumination that may be beyond the camera’s ability to compensate.
4. Keep the power cable away from water and other liquids. Never touch the power cable with wet hands.
Touching a wet power cable with your hands or touching the power cable with wet hands may result in electric shock.
5. Never install the camera in areas exposed to oil, gas or solvents.
Oil, gas or solvents may cause equipment failure, electric shock or, in extreme cases, fire.
6. Cleaning
For cameras with interchangeable lenses, do not touch the surface of the sensor directly with your hands. Use lens tissue or a cotton tipped applicator and ethanol to clean the sensor and the camera lens. Use a damp soft cloth to remove any dirt from the camera body.
Do not use complex solvents, or corrosive or abrasive agents to clean any part of the camera.
7. Do not operate the camera beyond the specified temperature, humidity and power source levels.
This camera is suitable for indoor operation only.
Use the camera at temperatures within -10°C ~ 50°C (14°F ~ 122°F) and humidity between
20 ~ 80%; this device is not rated as submersible. The input power source should be 12VDC or 24VAC. The use of a properly fused or “Class 2 Limited Power Source” power supply is highly recommended.
8. Mounting
Select a solid mounting surface that will support the weight of the camera and any additional loading from wind, snow, ice or other factors. Securely attach the camera to the mounting surface using screws and anchors that will properly support the camera. If necessary, (e.g. when mounting the camera to a drop ceiling, or unsupported ceiling) use a safety wire to provide additional support for the camera. i
Safety Notice
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
ATTENTION!
This is a class A product which may cause radio interference in a domestic environment; in this case, the user may be urged to take adequate measures.
This Product is RoHS compliant.
Your EverFocus product is designed and manufactured with high quality materials and components which can be recycled and reused. This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from your household waste. Please, dispose of this equipment at your local community waste
WEEE collection/recycling centre. In the European Union there are separate collection systems for used electrical and electronic product.
Please, help us to conserve the environment we live in!
ii
Contents
1. INTRODUCTION
........................................................................................ 1
1.1
P ACKING L IST .............................................................................................................. 1
1.2
F EATURES .................................................................................................................. 1
2. OVERVIEW
............................................................................................... 2
3. INSTALLATION
.......................................................................................... 2
3.1
L ENS I NSTALLATION AND A DJUSTMENT ................................................................................ 2
3.2
T OP / B OTTOM -M OUNT ................................................................................................. 3
4. BASIC CONNECTION
.................................................................................. 3
5
.
OSD MENU STRUCTURE
............................................................................ 4
6.
SPECIFICATIONS
........................................................................................ 6 iii
EQ700 True Day/Night Box Camera
1. Introduction
The EQ700 is a box camera equipped with 1/3” 960H SONY Exview HAD CCD II that produces 720TVL resolution 100% digital images, The camera delivers vastly superior video quality compared to traditional CCTV images. This superior resolution not only captures more critical evidentiary information, but the inherent ability for video also extends the area of coverage, expedites completion of investigations, resolves complaints and reduces both capital and operational costs.
The EQ700 provides 2D Noise Reduction to improve picture clarity while enabling DVRs to improve disk storage utilization . Full suite of OSD menu options controlled from the built-in function buttons.
Digital Wide Dynamic Range expansion to deliver properly exposed images despite bright light sources, deep shadows and/or unbalanced lighting in the same scene.
The EQ700 allows flexible choices of manual & DC iris control lenses with C / CS mount for outstanding coverage in a wide range of demanding surveillance environments while delivering stunning image quality.
1.1
Packing List
Camera Body x 1
Lens Cover x 1
DC Power Pigtail Cable x 1
C-mount Lens Adapter x 1
User Manual x 1
Hexagon Wrench x 1
1.2 Features
Ultra resolution of over 720 horizontal TV lines for astounding image quality
Exview HAD II sensor delivers amazing ultra high sensitivity of 0.0001 lux - 500X better native light sensitivity without DSS low light boost - Zero Ghosting guaranteed
Provides 2D-Noise Reduction to improve picture clarity while enabling DVRs to improve disk storage utilization
Full suite of OSD menu options controlled from the built-in control buttons
Digital Wide Dynamic Range expansion to deliver properly exposed images despite bright light sources, deep shadows and/or unbalanced lighting in the scene
1
EQ700 True Day/Night Box Camera
2. Overview
No. Name
1 Video Output
2 OSD Menu
3
4
5
Power LED
Grounding Stud
Power Input Terminal
3. Installation
Descriptions
Connects to DVR or monitor using a 75 Ohm BNC-type coaxial cable.
Use the function buttons to configure the settings in the
OSD menu.
Glows red then power is present.
Ensuring a good grounding when used.
Connects to 12VDC/24VAC power source.
3.1 Lens Installation and Adjustment
You can install either a CS-mount or a C-mount lens into the camera. It is recommended to use a lens with aperture ratio of F/1.2 or lower. Please refer to the following reference steps.
CS-Mount Lens:
1.
Remove the cover cap from the camera body.
2.
Install the lens into the camera body.
3.
Adjust the lens using the Focus / Zoom Screws.
2
EQ700 True Day/Night Box Camera
C-Mount Lens:
1.
Remove the cover cap from the camera body.
2.
Install the lens into the camera body using the supplied C-mount lens adapter.
3.
Adjust the lens using the Focus / Zoom Screws.
If you are using a DC Auto Iris lens :
1.
Remove the cover cap from the camera body.
2.
Install the lens into the camera body.
3.
Connect the DC Iris Cable to the DC Auto Iris Lens Connector.
Warning: Installing a C-mount lens without the C-mount lens adapter may damage the camera sensor.
3.2 Top / Bottom-Mount
You can use a mounting bracket and screw it on the top of the camera body to suspend the camera, or on the bottom of the camera body to support the camera.
4. Basic Connection
1.
Connect the camera to a device, such as a DVR, to display the image.
2.
Connect the camera to a 12VDC or 24VAC power source using the supplied DC Power Pigtail
Cable. The power LED will be lit in red.
3.
Connect the camera to a DVR or a monitor for setting image aim and focus before mounting the camera.
3
EQ700 True Day/Night Box Camera
5
.
OSD Menu Structure
The default value is marked with a star “*”.
No. Main Sub Menu Sub Menu / Function
1 Lens
Auto*
Type
Mode
Speed
DC*
AUTO*, Open, Close
0-255 (default=80)
Manual
2
Shutter
AGC
Auto*
Manual
ATW*
High
Luminance
Mode Shut + Auto Iris, Auto Iris*
Brightness 0-255 (default=24)
Mode AGC*, Off Low
Luminance
Mode
Shutter
Brightness x0.25, x0.50*, x0.75, x1.00
Shut+AGC
1/60*, 1/100, 1/250, 1/500, 1/1000, 1/2000,
1/4000, 1/10000
AGC
Speed
Delay CNT
6.00*, 12.00, 18.00, 24.00, 30.00, 36.00, 42.00,
44.80
0-255 (default=239)
0-255 (default=16)
ATW Frame x0.50, x1.0, x1.5, x2.0*
Environment Indoor*, Outdoor
Push
3
White
Balance
User1
B-Gain
R-Gain
0-255 (default=29)
0-255 (default=34)
User2
B-Gain
R-Gain
Anti CR
Manual Level
Push lock
4 Back Light Off* / BLC / HLC
0-255 (default=45)
0-255 (default=26)
24-90 (default=58)
Mirror Off* / On
Brightness 0-255 (default=0)
5
6
Picture
Adjust
ATR
Contrast 0-255 (default=128)
Sharpness 0-255 (default=128)
Hue
Gain
Off*
0-255 (default=128)
0-255 (default=150)
4
EQ700 True Day/Night Box Camera
On
Luminance
Contrast
Low, Mid*, High
Low, Mid-low, Mid, Mid-high, High*
Off*
7
Motion
Detection On
Detect Sense 0-127 (default=111)
Block Display Off*, On, Enable
Motion Area Off*, On
Area Select 1/4*, 2/4, 3/4, 4/4
Top / Bottom 0-244 (default=0)
Left / Right 0-474 (default=0)
Off*
8
9
10
Privacy
Day/Night
NR
On
EXT1
EXT2
Auto*
Color
B / W
NR Mode
Area Select 1/8*, 2/8, 3/8, 4/8,5/8, 6/8, 7/8, 8/8
Top / Bottom 0-244 (default=0)
Left / Right 0-474 (default=0)
Color 1-8 (default=1)
Transparent 0.00, 0.50, 0.75, *1.00
Mosaic
Burst
*Off / On
Off*/On
Delay CNT 0-255 (default=004)
Day → Night 0-255 (default=001)
Night → Day 0-255 (default=020)
Burst
IR Optimizer
Off* / On
Off
On*
Mode
Level
Off
Y/C*
Auto*/Center
0-31 (default=015)
Y Level 000-015 (default=003)
C Level 000-015 (default=003)
11
12
13
Camera ID
Sync.
Language
14 Camera Reset
15 Save all
Off*
On English letters, numbers and 28 symbols
Int.
English*, Japanese, German, French, Russian, Portuguese, Spanish Simplified
Chinese
5
EQ700 True Day/Night Box Camera
6.
Specifications
Camera
Part number
Pickup Device
Video Format
Image Pixels
Effective Pixels
Scanning System
Horizontal Resolution
Sensitivity
S/N Ratio
Electronic Shutter
Video Output
Gamma Correction
Lens Type
BLC
Gain Control
White Balance
Sync Mode
Day/Night
OSD Menu
OSD Languages
Digital Noise Reduction
ATR
Wide Dynamic Range
Mirror
Motion Detection
Privacy Mask
Environmental
Power Source
EQ700
1/3” Sony Exview HAD II 960H High Sensitivity Interline CCD
NTSC or PAL
1020 x 508 (NTSC) / 1020 x 596 (PAL)
976 x 494 (NTSC) / 976 x 582 (PAL)
2:1 Interlace
720+ TVL
Color ~ 0.001 lux, B/W ~ 0.0001 Lux / F=1.0
Over 50dB (AGC off)
1/60s~1/100,000s
BNC 1.0Vp-p 75Ω
0.45
C/CS Mount (lens sold separately)
OFF/BLC/HSBLC Selectable
Low light auto, bright light auto, manual selectable
ATW, One Push, User1, User2, Anti-Crawl, Manual, Push Lock
Internal Sync
True D/N with ICR; Auto
Multiple Functions
English, Spanish, French, Chinese, German, Japanese,
Portuguese, Russian
2D On/Off (Level adjustable)
On/Off (3 levels each adjustable for luminance and contrast)
On/Off (3 levels each adjustable for luminance and contrast)
Off/On
Off/On for 4 selectable zones (On screen indication on alarm)
Off/On for 8 selectable zones
Indoor
12VDC/24VAC
6
EQ700 True Day/Night Box Camera
Power Consumption
Operating Temperature
Humidity
Dimensions (L x W x H)
12VDC: 160mA , 2W max .
/24VAC: 2W max .
-10°C~50°C / 14°F~122°F
Less than 80% non-condensing
129x 58x 55mm /5.08” x 2.28” x 2.17”
Weight 240g / 0.53lbs
Certifications CE/FCC/RoHS
Specifications and designs are subject to change for improving the functionality of this product without notice.
7
EverFocus Electronics Corp.
EverFocus Taiwan:
12F, No.79, Sec. 1, Shin-Tai Wu Road,
Hsi-Chih, Taipei, Taiwan
TEL: +886 2 2698 2334
FAX: +886 2 2698 2380 www.everfocus.com.tw [email protected]
EverFocus Europe - Germany:
Albert-Einstein-Strasse 1, D-46446
Emmerich, Germany
TEL: +49 2822 93940
FAX: +49 2822 939495 www.everfocus.de [email protected]
EverFocus China - Beijing:
Room 609, Technology Trade Building,
Shangdi Information Industry Base,
Haidian District, Beijing 100085, China
TEL: +86 10 6297 3336~39
FAX: +86 10 6297 1423 www.everfocus.com.cn [email protected]
EverFocus USA - California:
1801 Highland Avenue, Unit A, Duarte, CA 91010,
USA
TEL: +1 626 844 8888
FAX: +1 626 844 8838 www.everfocus.com [email protected]
EverFocus China - Shenzhen:
4F, No. 2, D4 Building, Wan Yelong
Industrial Park, Tangtou Road, Shiyan,
Baoan, Shenzhen, Guangdong 518101, China
TEL: +86 755 2765 1313
FAX: +86 755 2765 0337 www.everfocus.com.cn [email protected]
EverFocus USA - New York:
415 Oser Avenue, Unit S, Hauppauge, NY 11788, USA
TEL: +1 631 436 5070
FAX: +1 631 436 5027 www.everfocus.com [email protected]
EverFocus Japan:
5F, Kinshicho City Building, 2-13-4
Koto-Bashi,Sumida-Ku, Tokyo, 130-0022, Japan
TEL: +81 3 5625 8188
FAX: +81 3 5625 8189 www.everfocus.co.jp [email protected]
EverFocus China - Shanghai:
Room 403, Ruijin Business Center, No.96, Zhaojiabang
Road, Luwan district, Shanghai 200020, China
TEL: +86 21 6471 2229 / 6471 2291
FAX: +86 21 6471 0566 www.everfocus.com.cn [email protected]
EverFocus India:
Suite 803, Housefin Bhavan, C-21, Bandra Kurla
Complex, Bandra (East), Mumbai 400051, India
TEL: +91 22 6128 8700
FAX: +91 22 6128 8705 www.everfocus.in [email protected]
Your EverFocus product is designed and manufactured with high quality materials and components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from your household waste.
Please, dispose of this equipment at your local community waste collection/recycling centre.
In the European Union there are electrical and electronic product.
Please, help us to conserve the environment we live in!
Ihr EverFocus Produkt wurde entwickelt und hergestellt mit qualitativ hochwertigen Materialien und
Komponenten, die recycelt und wieder verwendet werden können.
Dieses Symbol bedeutet, dass elektrische und elektronische Geräte am
Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden sollen.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Sammelstelle oder im Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu erhalten, in der wir leben
!
4605PQ0700X0100
Ver. B
advertisement
Related manuals
advertisement