- Computers & electronics
- Networking
- Network extenders
- Lightware
- WP-UMX-TPS-TX120-US Black
- Quick start Guide
advertisement
▼
Scroll to page 2
Front View Front View Legend 1 w q 9 8 7 2 3 4 5 6 Quick Start Guide WP-UMX-TPS-TX-120-US Black, White WP-UMX-TPS-TX130-US Black, White FP-UMX-TPS-TX130-MKM Rear View Show me Button Reset Button IR Detector HDMI Input DisplayPort Input Audio Input VGA Input Ethernet Input for an analog video source. Using a VGA cable where all the pins are wired (DDC channel) is highly recommended. Locking RJ45 connector for Ethernet communication. Video Select Manual switching between the video inputs. Audio Select Manual switching between the audio inputs. Lightware’s WP/FP-UMX-TPS extenders transmit universal video at a resolution up to 4K, audio and control up to 170 m distance over a single CATx cable. The products have HDBaseTTM integration with additional Lightware developments. This transmitter was designed for digital and analog video and audio signals e.g. DVI, VGA, YPrPb, HDMI1.4 and DP 1.1 with analog stereo audio from local inputs or embedded 7.1 HBR audio and to handle HDCP encryption. 2 3 2 3 TPS Output Port RS-232 Port DC Input 1 Box Contents Optional Accessories Power the device remotely by a PoE-compatible power injector (TPS-PI-1P1). If the device has to be powered by a local adaptor (PSU-48VP1), connect the output to the 2-pole Phoenix® connector on the rear of the wall plate. Please note that the 48V power adaptor is an optional accessory which can be purchased separately. The product is compatible with any HDBaseTTM third party devices. Switch/outlet box (B225R) for mounting VGA laptop OUT OUT -US X130 DMI-3 UT 8CH VGA DP HDMI ect Autosel RNET ETHE MX-T Max: SHOW ME S STATU INPUT RNET VGA DP HDMI ect Autosel AUDIO DP T HDMILink TPS RESE IN DP 2.5A 48 DC VGA Audio MacBook HDMI DP CATx Connect the transmitter and a compatible receiver or the matrix input board by a CATx cable via the TPS connectors. VGA HDMI DP Connect the transmitter and the sources using the inputs and VGA / DVI-I / HDMI / DisplayPort cables. Audio Optionally connect an asymmetric audio device with unbalanced audio signal (e.g. a VGA laptop) to the 2.5" TRS (jack) audio input port. LAN Optionally connect the transmitter to a LAN network in order to control the device. RS-232 Optionally connect a controller/controlled device (e.g. relay box) to the RS-232 port. Power See powering options in the Power Supply section. WP-UMX-TPS-TX130-US VIDEO SELECT WP-UMX-TPS-TX100 series transmitter Power Power adaptor Ethernet AUDIO SELECT AUDIO DP HDMI TPS LINK VGA DP HDMI Autoselect VIDEO VGA IN SHOW ME CATx INPUT STATUS AUDIO AUDIO IN IR RESET DP IN Compatible receiver or input board HDMI IN RS-232 Relay box LAN Ethernet 1 -P 5A S2-IB + TPS IN 3D AL DIGIT WITH 3D AND TPS IN OG TPS AUDIO TPS IN OUT 2 IN OUT 3 12V r on powe AUDIO TPS IN 3 r on 12V TPS powe 2 1 POE INPUT CATx (TPS) Power send -US X130 PS-T MX-T WP-U SHOW ME AUDIOT SELEC VIDEOT SELEC S STATU INPUT VGA DP HDMI ect Autosel AUDIO DP T HDMILink TPS RESE IR AUDIO 3 VIDEO 2 DP IN O 2. Remote power injector 3. Matrix board TPS-TX/RX90 and TPS-TX/RX95 are not PoE-compatible, thus not able to remote power the WP-UMX-TPS-TX100 series and vica versa. WP-UMX-TPS-TX100 series contains PoEcompatible remote power function, RX95 and TX95 extenders can be remote powered only by each other. Warranty void if damage occurs due to the usage of a different power source. The document is valid with the following firmware version: 1.2.0 The User’s manual of this appliance is available on www.lightware.com. See the Downloads section on the website of the product. Contact Us [email protected] +36 1 255 3800 [email protected] +36 1 255 3810 Lightware Visual Engineering LLC. Peterdy 15, Budapest H-1071, Hungary Doc. ver.: 2.2 19200079 4 ctor. Only use with conne 4 TPS IN IN RNET ETHE OUT TPS IN 3 2 OG ANAL TPS net WITH Ether D BOAR 3 2 ANAL AUDIO AND External power supply : 0.7A Typical1.5A Max: - + IN WITH TPS OUT 1 HDMI INPUT DC IR 3 2 O IN D FOR 48V- AUDIO VIDEO HDMI D WITH BOAR D-IB-A MX-TP 8 CH CATx (TPS) TPS-PI-1P1 -US ETHE DP UT IN OUTP DMI-3 BOAR 8CH 3 2 D FOR TPS 48V TPS MX-H O X130 48V DC Power adaptor IR AUDIO VIDEO PS-T WP-U AUDIOT SELEC VIDEOT SELEC -S S2-OB 5A DC AUDIO DP T HDMILink TPS RESE BOAR OUTP MX-TP 8 CH S STATU INPUT 1 D-OB MX-H SHOW ME AUDIOT SELEC VIDEOT SELEC OUT -A PS-T MX-T WP-U Power send Further Information HDMI laptop Compatible Devices The transmitters are compatible with all Lightware TPS receivers, matrix boards and third-party devices based on HDBase-TTM technology. AUDIO HDBaseTTM and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance. Connecting Steps The following accessories can be purchased separately: 48V DC power adaptor with interchangeable plugs VIDEO VGA AUDIO TPS LINK DP DP HDMI HDMI OFF: no TPS link between transmitter and receiver. Autoselect TPS LINK BLINKING (slow): low power mode is active. VIDEO AUDIO BLINKING (fast): Ethernet fallback mode is active. ON: TPS link is established, HDBaseT or Long Reach mode is active. 1. Local adaptor For white models in WP-UMX-TPS-100 series. For black models in WP-UMX-TPS-100 series. AUDIO DP HDMI TPS LINK Power Supply Options Phoenix Combicon 3-pole connector 2 AUDIO VGA DP HDMI Autoselect 48V DC Power adaptor Safety and Warranty Info, Quick Start Guide AUDIO DP HDMI TPS LINK VIDEO Autoselect LED OFF: autoselect is disabled. BLINKING: autoselect is enabled; searching for signal (video LEDs also blink). ON: autoselect is enabled; active video signal is found. A port is active if there is a valid signal on it. Quick Start Guide Fixing screws for mounting (4 pcs. 3.9x 22mm, PZ flat-head)2 VGA DP HDMI Autoselect Audio sources AUDIO VGA DP DP OFF: audio source is not selected. HDMI HDMI BLINKING: audio source is selected but not active. Autoselect TPS LINK AUDIO ON (with short pause): audio source is selected and the VIDEO port is active but not embedded to the output video stream. ON: audio source is selected, the port is active and the audio is embedded in the video. When Autoselect is enabled and video signal is not present at all, video LEDs blink. Locking RJ45 connector. Connect a twisted pair cable between the transmitter and the receiver. Remote powering also happens through this connector. 3-pole Phoenix connector for RS-232 serial port. 1 Fixing screws for mounting (4 pcs. 6-32 x 1”, oval head)1 Video sources OFF: video source is not selected. BLINKING: video source is selected but not active. ON: video source is selected and active. The transmitter can be powered by any of the following ways: 1 Introduction Safety and Warranty Info The LEDs give feedback about the state of the unit, the video and audio signals. See the attached list for details. Special functions are available with this button (e.g. enable DHCP (dynamic IP) or restore factory default settings). The same as disconnecting the device from the power source and reconnecting it again. IR Detector can sense IR light which can be forwarded to the receiver side or use for controlling functions. Input for a digital video source. Applied cable shall not be more, than 30 m (at 1080p) and 15 m (at 4K). Input for digital video source (only on TX130 models). Applied cable shall not be more, than 30 m (at 2.7 Gbps data speed). 3.5 mm Jack connector for unbalanced analog audio signal. Rear View Legend Please read and keep the information in the attached safety instructions supplied with the product before you start using the device. Transmitter unit Status LEDs PIN: 2mm Important Safety Instructions 1 2 3 4 5 6 7 8 9 q w Front Panel LEDs IN 4 ctor. conne Only use with Front Panel Button Functions The desired video input can be selected by pressing the Video select button on the front panel. The selection order of the inputs depend on the model as follows: TX120 models: VGA TX130 models: VGA Maximum Twisted Pair Distances Mounting Options - WP-UMX-TPS Wall Plates Video Input Selection HDMI DP VIDEO SELECT Autoselect Autoselect HDMI Audio Input Selection The desired audio input can be selected by pressing the Audio select button on the front panel. The selection order of the inputs depend on the model. AUDIO SELECT Below values are valid when the transmitter is powered by a local adaptor; distances may decrease depending on the powering mode (local or remote) and cable quality. Thanks to the design of Lightware devices, WP-UMX-TPS wall plates transmitter can be mounted easily into an industrial standard box as the figures show below. B225R switch/outlet box is not supplied with the product, it can be purchased separately. 1 2 3 109.2 70.6 1024x768@60Hz 1280x720p@60Hz 1920x1080p@60Hz (24bpp) 1920x1200@60Hz 1600x1200@60Hz 1920x1080@60Hz (36bpp) 3840x2160@30Hz UHD ** 4096x2160@30Hz 4K ** 100.6 If 4K video is selected to the output, analog audio cannot be embedded to the video stream due to the limitations of the video IC, thus the original audio stream will be transmitted. Cross Audio-embedding: The video and audio inputs can be combined with limitations. Below table contains the allowed connections: Video source DP Audio HDMI - DP - VGA - - The video and audio inputs can be also selected by using LDC (Lightware Device Controller), sending a protocol command, or using Autoselect. Lock / Unlock Buttons AUDIO SHOW SELECT ME Press the Audio select and the Show me buttons together. + 1. Keep the Show me button pressed for 5 seconds; all front panel LEDs start to blink. 2. Release the button, then press it 3 times quickly. DHCP is now enabled. SHOW ME + SHOW ME 5 sec Restore Factory Default Settings FP-UMX-TPS-TX130-MKM bracket is supplied with the product. It is compatible with the CRMB265 floorbox type (MK Cablelink Plus Modular series). 1 Set a Dynamic IP Address CAT7 AWG23 120 m / 170 m* 120 m / 170 m* 120 m / 170 m* 120 m / NA 120 m / NA 120 m / NA 100 m / NA 100 m / NA CAT7 SFTP AWG23 cable is always recommended. Mounting Options - FP-UMX-TPS-TX130-MKM Loose the two fixing screws on the top of the bracket. Insert the device into the frame. CAT7 AWG26 65 MHz 100 m / 130 m* 90 m / 120 m* 73.8 MHz 100 m / 130 m* 90 m / 120 m* 148.5 MHz 100 m / 130 m* 90 m / 120 m* 152.9 MHz 100 m / NA 90 m / NA 162 MHz 100 m / NA 90 m / NA 222.75 MHz 70 m / NA 70 m / NA 297 MHz 70 m / NA 70 m / NA 297 MHz 70 m / NA 70 m / NA ** If 4K video is selected to the output, analog audio cannot be embedded to the video stream due to the capabilities of the video IC, thus the original audio stream is transmitted. Fitting screw Front side of the transmitter B225R switch/outlet box 2 1 CAT5e AWG24 * Long reach TPS mode supports pixel clock frequencies up to 148.5 MHz. 3 Audio source HDMI Cable lengths (Auto / Long reach TPS mode) Pixel clock rate Resolution Release and remove the fixing screws from the front side of the extender. Insert the extender into the B225R outlet box and position it to get the holes aligned. Fasten the front side of the extender to the B225R outlet box by fitting all the screws. 1. Keep the Show me button pressed for 10 seconds. After 5 seconds front panel LEDs start to blink but keep the button pressed. The LEDs start to blink faster 5 seconds later. 2. Release the button, then press it 3 times quickly; factory default settings are restored: the fixing screws 3 Fasten to fix the device into the floorbox frame. the handles 2 Move towards the frame. Align IP Address (static) Subnet Mask Static Gateway DHCP TCP/IP Port No. Selected Output port Autoselect Output TPS Mode Emulated EDID RS-232 Mode RS-232 Control Protocol RS-232 Port Setting RS-232 Command Injection Port No. IR Command Injection Port No. (local) IR Command Injection Port No. (TPS) the tab on the assembly with the slot in the frame. 3x Tab Fixing screw Software Control – Using Lightware Device Controller (LDC) Handle The device can be controlled from a computer through the Ethernet port using Lightware Device Controller. Please download the application from www.lightware.com, install on a Windows PC or a Mac OS X and connect to the device via the Ethernet port. LDC software contains many useful built-in tools which can be used for signal analysis like the followings: FP-UMX-TPS-TX130-MKM FP-UMX-TPS-TX130-MKM bracket 53.4 217 77 Port Diagram (of TX130 models) 192.168.0.100 255.255.255.0 192.168.0.1 Disabled LW2: 10001; LW3: 6107 Video: VGA; Audio: Analog Audio input Disabled Auto VGA port: F89; DP, HDMI ports: Dynamic Pass-through LW2 57600 BAUD, 8, N, 1 Local: 8001; TPS: 8002 Input: 9001; Output: 9002 Input: 9003; Output: 9004 Typical Application CATx De (IE vic Fo EE e can r 802 bes .3a be t per f) rem for ote r S Lo PIN: 2mm ng port ce ta n is D ed er ei v ec R HD T MI- PS 9 -RX 7 Ethernet switch HDMITPS-RX97 CATx Blu-ray player WiFi access LAN MAC S IR RS-232 TP E le Po y cab h wit TP SF link in RoH EU S , Hun gar CA T7 TP de or Ma analog audio ove TPS DP Laptop CA T6 TPS out 2m 1A m DC VGA WP-UMX-TPSTX130-US Black HDMI we red A/D converter O Ethernet RS-232 in/out A/D converter IN G2 3 3 DP po Processor IR IO Local DC cable PIN 12V : AUDIO DP HDMILink ET TPS RES TPS-PI-1P1 AW Analog stereo audio US AUD 2 Embedder Audio in T STAT O 2.5A IN use INPU VGA DP HDMI elect Autos VIDE Analog video in SHO ME IO AUDECT SEL O VIDE ECT SEL VGA in 48V DC Power adaptor DC ma nce IR detector ET De-embedder 48 W ERN Digital video in TX1 WP ETH DP in Max: : 0.7A Typical1.5A Max: - + S 30-U PSX-T -UM sup 4K 00 I, 3D, 10/1 l IR RS-232 HDM rnet iona l Ethe rect iona Bidi rect Bidi Power send De-embedder Sn : HDMI in Digital video in LAN IN (PoE ) HDMI HD Projector
advertisement
Related manuals
advertisement