HR 2305/B

Philips Domestic Appliances and Personal Care

Service Manual

PRODUCT INFORMATION

Power consumption motor : 30 W Ice-cream selector switch

Voltage : 220/230 V, 50-60 Hz When the “soft ice” switch is pressed, the stirrer will start

Length of mains cord : 140 cm rotating at a relatively high speed (approx. 70 rpm, gradually

Freezing time of cooling disc : 18 hrs decreasing to approx. 50 rpm., depending upon the mixture).

After approx. 20 minutes, the green pilote light will start to blink.

Weight of product : 3.4 kg

Up to 10 minutes after switching on, you can switch from making

Dimensions product l x w x h : 23 x 25 x 27 (cm)

“Compact ice” to making “Soft ice” (or the other way round).

Type no. cooling disc : HR 2968

If “Soft ice” has been selected and the ice-cream maker is not

Speeds : been switched off after 30 minutes, the appliance will reduce stirrer speed to keep the “Soft ice” longer in optimum condition.

Cooling disc/container is to be kept in a 3 or 4-star freezer or freezing compartment of the refrigerator.

When the “Compact ice” switch is pressed, the stirrer will start rotating at a relatively low speed (approx. 21 rpm).

After approx. 40 minutes, the green pilot light will start to blink.

The stirrer should actually be functioning when the bowl is being fi lled otherwise the ingredients will immediately freeze onto the cooling disc.

The blinking pilot light means that the minimum processing time for a standard quantity of the selected type of ice cream has elapsed.

Safety shut-off

The ice-cream maker is equipped with a safety shut-off.

This device automatically switches off the appliance after

120 minutes of operation, or if overloading occurs.

Cooling down time: approx. 55 min.

SERVICE INFORMATION

Soft

Compact wt wt/rd wt/rd (x)

- Gas pressure may cause the cooling disc to bulge out so that it is impossible to assemble it into the appliance.

If this has happened proceed as follows:

1. Remove plug (item 16) which is fi xed with snap tabs.

2. Bring the cooling disc back into its original fl at shape and, while doing so, insert a new plug (item 16).

- Use grease 4822 390 20004 on the metal gearwheel shafts

1 rd

2 rd

3 rd

4 in the gearbox.

- Motor control without de-soldering (see wiring diagram):

Resistance must be between 1-2 = 440 ± 50 ohm and between 3-4.

- If a repair has been executed, make sure that all functions of the appliance are working correctly.

DAP0153

Hall

Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved

4322 277 00155

99/12

PCS 101 330

Subject to modification

HR 2305/B

1

14

2

3

8

10

9

11

16

15

17

4

12

5

6

7

13

18

19

1 4203 065 62360 upper housing

2 4822 321 62806 hall assy

3 4822 214 70585 pcb 220 V

4 4822 522 10477 gear box

5 4203 065 62370 fl ex

6 4822 502 30005 screw 3.5 x 25

7 4203 065 62380 coupling assy

8 4822 502 30054 screw 2.5 x 13

9 4822 361 30446 motor 220 V

10 4822 522 33531 drive gear wheel

PCS 101 330

DAP 0151

11 4822 466 62531 buffer

12 4822 466 62608 sealing ring

13 4203 065 62390 lower housing

14 4203 065 62400 container cover

15 4203 065 62410 stirrer

16 4822 267 31056 plug cooling-disc

17 4822 511 90025 cool disc

18 4203 065 62420 container

19 4822 462 40374 stud

DFU 4203 064 12000