advertisement
6144
Indoor PTZ Dome Camera with Fan
6154
Outdoor PTZ Dome Camera with Fan & Heater
9
The 6144 (Indoor) and 6154 (Outdoor) high-resolution Pan
Tilt Zoom Color Dome Cameras are perfect for high-end surveillance systems. Their built-in multi-protocol decoders allow the cameras to be controlled using either Pelco D or
Pelco P protocols. Built-in heating elements and cooling fans ensure continued operation even when under extreme ambient conditions.
Features: h High quality color CCD image sensor h 500 TV lines of resolution h Built-in multi-protocol decoder: Pelco P or Pelco D h Up to 256 selectable camera IDs h 360º Pan rotation and 90º Tilt movement h Non-volitile memory retains settings during power loss h Built-in heating elements(6154 only) and cooling fans
Pan Tilt Zoom Dome Cameras Include:
6154 Camera 6144 Camera
2
Wall Mount Pendant Mount
Power Supply
Accessory Pack
Accessories:
Camera Pigtail
Length: 80”
Wiring Detail
Orange (RX+)
Yellow (RX-)
Black Video Gnd (VG)
Clear Video Signal (VO)
Black (AC24V)
Red (AC24V)
6144
120.0
Dimensions
Units: mm
6154
215.5
99.5
71.1
224.5
196.5
99.5
71.1
52.0
Ø101.0
118.4
141.7
52.0
Ø101.0
118.4
141.7
Accessing the DIP Switches
There are several configuration DIP switches located underneath the dome cover of the camera. Please follow the steps below to safely remove the dome cover. After the configuration switches have been set, follow these steps in reverse order to reinstall the dome cover.
See the following page for configuration details.
120.0
ON DIP
2. To release the inner dome, remove
the 4 screws holding it in place.
1. Unscrew the clear dome to remove it.
3
4
DIP Switch Settings
ON DIP PTZ Protocol Settings...
These DIP switches select the PTZ protocol and baud rate that will be used for communication between the camera and PTZ controller.
Follow the table below.
Auto Detect
Pelco-D(2400)
Pelco-P(4800)
2400bps
4800bps
9600bps
19200bps
1
Off
Off
Off
Off
Off
On
On
2 3 4
Off Off Off
Off On Off
On On On
Off
On
Off
Baud
Rates
On
Example... This switch configuration will make the camera respond to
Pelco-D at 2400bps.
ON DIP
Camera ID Settings... These DIP switches set the camera ID that will allow your PTZ controller to send discrete commands to move this specific camera. You can set the ID anywhere between 0 and 255. See the example below to learn how to set these switches.
Example... To calculate the camera ID, add up all the values of the switches in the “ON” position.
Switch
Value
128
64
32
16
8
4
2
1
Switch
Position
Off
On
Off
Off
Off
On
Off
Off
Camera ID
Calculation
+
0
64
0
0
0
4
0
0
Camera ID = 68
Installation
Note: The installation of the 6154 camera is shown below. The 6144 comes with a different mount, but the installation is otherwise identical.
Wall Mount
Camera
Pigtail
1. Drill a hole for wiring to exit the wall.
2. Feed camera pigtail through the base of the wall mount.
3. Attach mount to wall with screws.
4. Connect camera pigtail to the base of the camera.
5. Secure the camera to the mount using the set screw.
Set Screw
BNC connector
Wire Extensions
(not included)
RS-485
Connector
To Video
Display
To PTZ
Controller
Crimp-on splice
connectors
(not included)
Power Supply
6. Connect the camera pigtail to wire extensions or directly to a video display system.
7. Connect the BNC video output to a monitor or distribution system.
8. Connect RS-485 wires to
PTZ controller.
9. Connect power supply.
5
6
Problem
Trouble Shooting
Possible Cause
No motion and no video output
Power supply is disconnected or damaged.
Solution
Check power supply. Replace if needed.
Normal Video output but abnormal motion
Power supply voltage is too low.
Make sure to use the correct power supply.
Move the power supply closer to the camera.
Have motion control, but no video
Faulty coax connection.
Check with cable tester or verify cable by sending known good video signal through it.
Normal video output, but no motion control
Camera protocol does not match controller.
Check the DIP
Switches.
*Specifications
Image Sensor:
Picture Elements:
Resolution:
S/N Ratio:
Min Illumination:
Electronic Shutter:
Iris Control:
1/3” Hi-Res CCD
NTSC: 768x494
500 lines
More than 48 dB
0.7 Lux @ F1.8
1/60s - 1/120,000s
Automatic/Manual
White Balance: Automatic
Gamma Characteristic: 0.45
Focus:
Optical Zoom:
Auto/Manual/One push
10X, f = 3.8 to 38.00mm
Min. Focal Distance:
Digital Zoom:
Zoom Speed:
Angle Field of View:
1.000mm
Off/On (X2 - X10)
1.67 sec: Wide to Tele
Sync. System:
Power Supply:
Power Consumption:
Video Output:
RS-485 Camera ID:
H: 51.2°(wide) - 5.58º(tele)
V: 39.3°(wide) - 4.27º(tele)
Internal
24VAC, 2Amps
38Watts (max with heaters on)
1 Vp-p @ 75 ohms
Selectable: 0-255
Weather Resistance: 6154: IP66 for Outdoor use
6144: Indoor use only
Operating Temp (6144): -10°C to +45°C (14°F to 113°F)
Operating Temp (6154): -30°C to +60°C (-22°F to 140°F)
Operating Humidity:
Storage Temp:
Storage Humidity:
0% to 90% (non-condensing)
-20°C to 60°C (-4°F to 140°F)
0% to 95% RH
*Specifications subject to change without notice.
7
Channel Vision Technology will repair or replace any defect in material or workmanship which occurs during normal use of this product with new or rebuilt parts, free of charge in the USA, for two years from the date of original purchase. This is a no hassle warranty with no mail in warranty card needed. This warranty does not cover damages in shipment, failures caused by other products not supplied by Channel Vision Technology, or failures due to accident, misuse, abuse, or alteration of the equipment. This warranty is extended only to the original purchaser, and a purchase receipt, invoice, or other proof of original purchase date will be required before warranty repairs are provided.
Mail in service can be obtained during the warranty period by calling
(800) 840-0288 toll free. A Return Authorization number must be obtained in advance and can be marked on the outside of the shipping carton.
This warranty gives you specific legal rights and you may have other rights (which vary from state to state). If a problem with this product develops during or after the warranty period, please contact Channel
Vision Technology, your dealer or any factory-authorized service center.
w w w . c h a n n e l v i s i o n . c o m
234 Fischer Avenue, Costa Mesa, California 92626 USA
(714)424-6500 (800)840-0288 (714)424-6510 fax email: [email protected]
500-230 rev D
advertisement
Related manuals
advertisement