Height Strip Covert Camera

Please read this manual thoroughly before use, and keep it handy for future reference.

Design and specifications are subject to change without notice.

FCC COMPLIANCE STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC INFORMATION : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CE COMPLIANCE STATEMENT

WARNING : This is a Class A poduct. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

2

IMPORTANT SAFETY INSTRUCTIONS

1 . Read these instructions .

2

.

Keep these instructions

.

3 . Heed all warnings .

4 . Follow all instructions .

5 .

.

Do not block any ventilat ion openings . Install in accord ance with the manufacturer`s instructions .

6. Do not install near any heat sources such as radiators, heat registers , stoves , or other apparatus

( including amplifiers

) that produce heat

.

7 . Only use attachments / accessories specified by the manufacturer .

8 . Use only with the ca rt , stand , tripod , bracket , or table specified by the manufacturer

, or sold with the apparatus

.

When a cart is used

, use caution when moving the cart

/ apparatus combination to avoid injury from tip over .

9

.

CAUTION - THESE SERVICING IN STRUCTIONS ARE FOR USE BY

QUALIFIED SERVICE PERSONNEL ONLY

.

TO REDUCE THE RISK OF

ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN

THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU

ARE QUALIFIED TO DO SO .

10 . Use satisfy clause 2 .

5 of IEC60950 1 / UL 60950 1 or Certified / Listed Class 2 power source only .

11. Indoor use only .

EXPLANATION OF GRAPHICAL SYMBOLS

3

4

Step 1

Drill feed-thru hole for cable on mounting surface 63.27" above the finished floor.

5

Step 2

Feed wire through the 1.0 inch hole on the gimble mount.

6

Step 3

Center the gimbal mount to mounting surface and mark the mounting holes for the gimbal mount on the surface.

Secure the gimbal mount to the surface using installer supplied self tappers for aluminum frame structure.

If mounting on soft surface such as drywall be sure to use to use anchors.

7

Step 4

Completing the housing installation

Remove the five white head M4 screws that hold the face plate to the housing

and set the face plate aside.

Feed the wire coming through the gimbal mount through the 3/4" hole in the

back of the camera housing.

Attach the camera housing to the gimbal mount using the M6 Allen head screws

and washer previously removed.

Place the external tooth washer between the housing and the gimbal mount then

the split lock washer on the M6 screw and insert the screw into the housing

through the gimbal mount and external tooth lock wasker.

Install the bolt and washers assembly at the bottom and top of the gimbal mount

finger tight. (See Figure-1)

M6 Allen head screw

Split lock washer between gimbal mount and housing

External tooth lock washer under head of bolt

Figure-1

After connecting the video and power to their proper connections replace the

face plate that was removed in an earlier step using the five screws.

Adjust the position of the housing in the gimbal mount for the proper view and

then tighten the top and bottom Allen head screws using an Allen head wrench.

Verify that the housing is in the proper position and is secure.

8

Optional Camera Height Setting

1. The Height strip camera has the capability to be set in the housing at 5ft or

5.5ft above the floor.

The default setting of the camera is set to 5.5ft.

If the lower setting is desired the following housing change must be

completed.

* Remove housing from gimbal

* Note the position of the hole in the housing base for cable throughput

1

2

The cable hole is at the center of the mounting bracket

* Remove four Allen flat head screws along each side of the housing and

separate the front cover with the camera from the housing base.

Figure-2

Allen flat head screw

* Replace the front cover with the camera to the housing base after turning the cover 180 f r om original position.

Replace the three Allen head screws along each side of the housing and continue the installation

2. Camera lens position can be adjusted up and down 5 degrees.

5 o

[ft] [cm]

Figure-3 3. Two height marker strips are provided, one marked in feet

and one marked in centimeters. Use the appropriate one.

(See Figure-3)

5 o

9

55.0 x 43.0(53.3) x 872.0 mm

2.17 x 1.69(2.10) x 34.33 inch

DIMENSIONS

HEIGHT STRIP CAMERA

10

STRUCTURE OF THE SETUP MENU

<SETUP>

LENS

EXPOSURE

BACKLIGHT

WHITE BAL

DAY&NIGHT

IMAGE

FUNCTION

SYSTEM

EXIT

<LENS>

DC

MANUAL

<EXPOSURE>

SHUTTER

AGC

SENS-UP

BRIGHTNESS

D-WDR

DEFOG

RETURN

<BACKLIGHT>

OFF

BLC

HSBLC

<WHITE BAL>

ATW

AWC->SET

INDOOR

OUTDOOR

MANUAL

AWB

<DAY&NIGHT>

AUTO

COLOR

B&W

<IMAGE>

SHARPNESS

LSC

D-EFFECT

RETURN

<FUNCTION>

DNR

MOTION

PRIVACY

DEFECT DET

RETURN

<SYSTEM>

CAMTITLE

MONITOR

VIDEO OUT

LANGUAGE

COMET

RETURN

<RESET>

SAVE&END

RESET

NOT SAVE

11

LENS

The EXPOSURE menu is used to set the automatic light control method for the camera.

It provides the ability to adjust the SHUTTER speed. AGC SENS-UP, BRIGHTNESS, D-WDR,

and DEFOG functions of the camera.

1) DC

Select the DC mode. ▶ INDOOR, OUTDOOR

Select the DC iris speed ▶ 0~15

2) MANUAL Select the MANUAL mode

MAIN MANU

LENS

EXPOSURE

WHITE BAL

DC

BACK LIGHT OFF

ATW

AUTO DAY&NIGHT

IMAGE

FUNCTION

SYSTEM

EXIT SAVE&END

MAIN MANU

LENS

EXPOSURE

WHITE BAL

MANUAL

BACK LIGHT OFF

ATW

AUTO DAY&NIGHT

IMAGE

FUNCTION

SYSTEM

EXIT SAVE&END

NOTE Choose when installed in an external DC mode outdoor.

EXPOSURE

The EXPOSURE menu is used to set the automatic light control method for the camera .

It provides the ability to adjust the SHUTTER speed , AGC , SENS-UP , BRIGHTNESS , D-WDR , and DEFOG functions of the camera .

1) SHUTTER

Select the SHUTTER speed level.

▶ Auto, 1/60(50), FLK~1/240 – 1/50000, x2 ~ x30

2) AGC

Adjust the Auto Gain Control level. ▶ OFF, Auto (x2 ~ x30)

3) SENS-UP

Select the Digital Slow Shutter level. ▶ OFF, AUTO (x2 ~ x30)

4) BRIGHTNESS

Adjust the BRIGHTNESS level. ▶ 0 - 100

5) D-WDR

Select the Digital WDR. ▶ AUTO, ON(level 0~8), OFF

6 ) DEFOG

Select the DEFOG mode.

▶ AUTO, ON(level 0~8), OFF

POS/SIZE

GRADATION

DEFAULT

< EXPOSURE >

MODE

Adjust the window position & size

▶ 0 ~ 2

Initialize the setting values

MAIN MANU

LENS

EXPOSURE

WHITE BAL

DC

BACK LIGHT OFF

ATW

AUTO DAY&NIGHT

IMAGE

FUNCTION

SYSTEM

EXIT SAVE&END

SHUTTER

AGC

AUTO

|▪▪▪ l ▪ | 11

SENS-UP AUTO

BRIGHTNESS | ▪▪ l ▪▪ | 48

D-WDR

DEFOG

RETURN

OFF

OFF

RET

12

BACKLIGHT

The BACKLIGHT menu is used to the ability to prevent back lighting from the image.

1) BLC

Prevents such a back light effect to secure a clear image under All illumination environments.

Adjust the size of Back Light Compensation area.

LEVEL

AREA

DEFAULT

Select the BLC gain ▶ Low, Middle, High

Adjust the window position & size

Initialize the setting values

2)HSBLC

Mask the high light zone with specific color & level.

SELECT

Select the HSBLC area ▶ AREA1 - AREA4

DISPLAY

Adjust the HSBLC area window position & size

BLACK MASK

Select the BLACK MASK ▶ ON, OFF

LEVEL

MODE

Select the HSBLC level ▶ 0 ~ 100

All Day, Night

DEFAULT Initialize the setting values.

< BACKLIGHT >

MAIN MANU

LENS

EXPOSURE

WHITE BAL

DC

BACK LIGHT OFF

ATW

AUTO DAY&NIGHT

IMAGE

FUNCTION

SYSTEM

EXIT SAVE&END

BLC

LEVEL

AREA

DEFAULT

RETURN

MIDDLE

RET

HLBLC

SELECT

DISPLAY

BLACK MASK ON

LEVEL

MODE

DEFAULT

RETURN

AREA

ON

|▪▪ l ▪▪

RET

| 30

ALL DAY

13

WHITE BALANCE

The screen color can be adjusted by using the Auto White Balance function.

It compensates for deviations in the white color caused by changes in the color temperature of the light source so that the colors are reproduced correctly.

1)ATW

Automatically adjust color temperature.

2)AWC->SET

Automatically readjust only by pressing AWC → SET.

3)INDOOR

Set the color temperature to 3200°K

4)OUTDOOR

Set the color temperature to 6300°K

5)MANUAL

6)AWB

Manual mode.

User can change Red and Blue gain value manually.

BLUE

RED

0 ~ 100

0 ~ 100

Automatically extended range of color temperature adjustment.

< WHITE BALANCE >

MODE

MAIN MANU

LENS

EXPOSURE

DC

BACK LIGHT OFF

WHITE BAL ATW

DAY&NIGHT AUTO

IMAGE

FUNCTION

SYSTEM

EXIT SAVE&END

MANUAL

BLUE

RED

RETURN

|▪▪ I ▪▪ | 50

|▪▪ I ▪▪ | 50

RET

14

DAY&NIGHT

The DAY&NIGHT menu is used to configure the day and night related.setting for the camera.

1) D&N AUTO

-Input Method

CDS

DAY&NIGHT

mode are changed according to the sensor inputs

D&N LEVEL

Adjust levels of transition

▶

0 255

255

N&D LEVEL

DELAY

Adjust levels of transition

1-60 SEC

-Input Method

AGC

▶

0 -

DAY&NIGHT mode are changed according to the brightness of the image.

Use only when the camera is installed in a dark place but the camera is viewing a bright place.

When used in a normal installation, hunting may occur.

D &N LEVEL

Adjust levels of transition

▶

0 255

N&D LEVEL

Adjust levels of transition

▶

0 255

DELAY 1-60 SEC

2) D&N B&W

IR SMART

< DAY&NIGHT >

MODE

LEVEL

1~15

AREA

Adjust the window position & size.

MAIN MANU D&N AUTO

LENS

EXPOSURE

BACK LIGHT OFF

WHITE BAL

DAY&NIGHT

IMAGE

FUNCTION

SYSTEM

EXIT

DC

ATW

AUTO

SAVE&END

D N (CDS) |▪▪▪ I ▪ | 206

D N (DELAY) |▪ I ▪▪▪ | 3

N D (CDS) |▪▪▪ I ▪ | 180

N D (DELAY) |▪ I ▪▪▪ | 3

RETURN RET

B&W

IR SMART

RETURN

ON

RET

15

The IMAGE menu provides the ability to adjust the SHARPNESS, LSC and D-EFFECT functions of the camera.

1) SHARPNESS

Adjust the SHARPNESS level. ▶ OFF, AUTO (0 - 10)

2) LSC

Select the lens Lens Shading Compensation. ▶ ON, OFF

3) D-EFFECT FREEZE

Select real or still mode ▶ ON, OFF

MIRROR

Select OFF, MIRROR, V-FLIP, ROTATE

NEG. IMAGE

Select Negative image mode ▶ ON, OFF

MAIN MANU

LENS

EXPOSURE

BACK LIGHT OFF

WHITE BAL

DAY&NIGHT

IMAGE

FUNCTION

SYSTEM

EXIT

DC

ATW

AUTO

SAVE&END

< SHARPNESS >

IMAGE

SHARPNESS

LSC

D-EFFECT

RETURN

< D-EFFECT >

IMAGE

SHARPNESS

LSC

D-EFFECT

RETURN

AUTO

OFF

RET

AUTO

OFF

RET

IMAGE

SHARPNESS

LSC

D-EFFECT

RETURN

AUTO

OFF

RET

SHARPNESS

LEVEL

SMART AGC

END AGC

RETURN

|▪▪ I ▪▪ | 5

|▪▪▪ I ▪ | 128

|▪▪▪ I ▪ | 160

RET

D-EFFECT

FREEZE

MIRROR

NEG. IMAGE

RETURN

OFF

OFF

OFF

RET

16

FUNCTION

The IMAGE menu provides the ability to adjust the DNR, MOTION, PRIVACY and

DEFECT DET functions of the camera.

1) DNR

2D

3D

2) MOTION

SELECT

Select Digital Noise Reduction.

▶ OFF, LOW, MIDDLE, HIGH

▶ OFF, LOW, MIDDLE, HIGH

Detects the Motioned Object in the image. ▶ ON, OFF

Select the Motion area ▶ AREA1 - AREA4

DISPLAY

SENSITIVITY

COLOR

TRANS

ALARM

TIME

DEFAULT

Adjust the Motion sensitivity level ▶ 0 - 100

Select the motion area color ▶ WHITE - Red, Green, Blue

Select the motion area transparency.

Select the Motion alarm

▶

Select the Motion Alarm time ▶ 1 - 15

Initialize the setting values

1.0, 0.75, 0.5, 0.25

VIEW TYPE Select view type of the Motion area ▶ OFF, BLOCK, OUTLINE, ALL

OSD VIEW Select the Motion OSD view ▶ OFF, ON

3) PRIVACY

SELECT

DISPLAY

COLOR

Hide an area you want to hide on the screen.

Select the privacy zone ▶ AREA1 - AREA4

Adjust the Privacy window type, position & size

▶ OFF, INV., MOSAIC, COLOR

Select the privacy zone color ▶ WHITE - USER

Select the privacy zone transparency ▶ 1.0, 0.75, 0.5, 0.25

Initialize the setting values

TRANS

DEFAULT

4) DEFECT DET

LIVE DPC

WHITE DPC

POS/SIZE

Compensates for bad pixels.

Select the Live DPC mode ▶ OFF, ON

AGC LEVEL Select the AGC level ▶ 0 - 255

LEVEL

Select the Live DPC level ▶ 0 - 100

Select the White DPC mode ▶

Start the white pixels correction

OFF, ON

Adjust the White DPC area window position & size

START

DPC VIEW

LEVEL

▶ OFF, ON

Select the White DPC level ▶

AGC

SENS-UP

BLACK DPC

Select the AGC Level ▶ 0 - 14

0 - 60

Select the Sens-up level ▶ x2 - x30

Select the Black DPC mode ▶ OFF, ON

POS/SIZE

START

Adjust the Black DPC area window position & size

DPC VIEW

▶ OFF, ON

LEVEL

Start the Black pixels correction

Select the Black DPC level ▶ 0 - 100

<FUNCTION>

MAIN MANU

LENS

EXPOSURE

WHITE BAL

DC

BACK LIGHT OFF

ATW

AUTO DAY&NIGHT

IMAGE

FUNCTION

SYSTEM

EXIT SAVE&END

FUNCTION

DNR

MOTION

PRIVACY

DEFECT DET

RETURN

OFF

OFF

17

<DNR>

FUNCTION

DNR

MOTION

PRIVACY

DEFECT DET

RETURN

OFF

OFF

RET

<MOTION>

FUNCTION

DNR

MOTION

PRIVACY

DEFECT DET

RETURN

OFF

OFF

RET

<PRIVACY>

FUNCTION

DNR

MOTION

PRIVACY

DEFECT DET

RETURN

OFF

OFF

RET

<DEFECT DET>

FUNCTION

DNR

MOTION

PRIVACY

DEFECT DET

RETURN

OFF

OFF

RET

2D

3D

RETURN

DNR

MIDDLE

MIDDLE

OFF

MOTION

SELECT

DISPLAY

SENSITIVITY

COLOR

TRANS

ALARM

DEFAULT

RETURN

AREA1

ON

|▪ I ▪▪▪ | 10

WHITE

1.0

RET

PRIVACY

SELECT

DISPLAY

COLOR

TRANS

DEFAULT

RETURN

AREA1

COLOR

WHITE

1.0

RET

DEFECT DET

LIVE DPC

WHITE DPC

BLACK DPC

RETURN

ON

ON

OFF

RET

DEFECT DET

LIVE DPC

WHITE DPC

BLACK DPC

RETURN

ON

ON

OFF

RET

CLOSE THE IRIS

THEN

PRESS ENTER

DEFECT DET

LIVE DPC

WHITE DPC

BLACK DPC

RETURN

ON

ON

ON

RET

LIVE DPC

AGC LEVEL

LEVEL

RETURN

| ▪ I ▪▪▪ | 4

| ▪ I ▪▪▪ | 2

RET

WHITE DPC

POS/SIZE

START

DPC VIEW

LEVEL

AGC

SENS-UP

RETURN

OFF

| ▪▪▪▪ | 4

| ▪▪▪▪ | 14

X2

RET

WAITING...

BLACK DPC

POS/SIZE

START

DPC VIEW

LEVEL

RETURN

OFF

| ▪▪▪▪ | 100

RET

18

SYSTEM

The IMAGE menu provides the ability to adjust the CAM TITLE, RS485, MONITOR, CVBS CROP,

VIDEO OUT, LANGUAGE and VERSION functions of the camera.

1) CAM TITLE

2) MONITOR

LCD

BLUE GAIN

RED GAIN

GAMMA

CRT

BLUE GAIN

RED GAIN

GAMMA

4) VIDEO OUT

5) LANGUAGE

6) COMET

Maximum of 15 characters are allowed.

Select the Monitor type ▶ LCD, CRT

Adjust the Blue gain level ▶ 0 - 100

Adjust the Red gain level ▶ 0 - 100

Select the gamma level ▶ USER, 0.45 - 1.0

Adjust the Blue gain level ▶ 0 - 100

Adjust the Red gain level ▶ 0 - 100

Select the gamma level ▶ USER, 0.45 - 1.0

Select the video out type ▶ NTSC, PAL

OSD menu LANGUAGE (16ea) ▶ ENGLISH etc.

Select the COMET function ▶ OFF, ON

<SYSTEM>

MAIN MANU

LENS

EXPOSURE

WHITE BAL

DC

BACK LIGHT OFF

ATW

AUTO DAY&NIGHT

IMAGE

FUNCTION

SYSTEM

EXIT SAVE&END

SYSTEM

CAM TITLE

MONITOR

VIDEO OUT

LANGUAGE

COMET

RETURN

OFF

LCD

NTSC

ENGLIS

H OFF

RET

<CAM TITLE>

SYSTEM

CAM TITLE

MONITOR

VIDEO OUT

LANGUAGE

COMET

RETURN

OFF

LCD

NTSC

ENGLISH

OFF

RET

CAM TITLE

0 1 2 3 4 5 6 7 8 9

A B C D E F G H I J K

L M N O P Q R S T U V

WXYZ ▶ → ← ↑ ↓ ()

¯ － _■ /=& : ~ , .

← → CLR POS END

_ _ _ _ _ _ _ _ _ _

19

20

SPECIFICATIONS

Power

General

Function

Connector

&

ETC

MODEL

Power Source

Power Consumption

Image Sensor

Total Pixels

Active Pixels

Scanning System

Sync. System

Video Frame Rate

Min. illumination

Video Output

Camera Control

S/N Ratio

Lens

Exposure

Shutter

AGC

Sens-UP

Brightness

D-WDR

Defog

Backlight

White Balance

Day & Night

DNR

2DNR

3DNR

Camera Title

S

P

E

C

I

A

L

D-Effect

Motion Detection

Privacy Masking

Language

Defect Detection

Sharpness

Monitor

LSC (Shading)

Video mode

Save & Exit

Power input

Video output

Transmission Distance

Lens mount

Lens

Operating temperature

Operating humidity

External dimension

Weight

Height Strip Covert Camera

DC12V ± 10%

Max 2.2 Watts (180mA)

1/2.9" 2.1M Sony CMOS

2000(H) x 1121(V)

1920(H) x 1080(V)

Progressive

Internal

1920×1080p@25 fps ； 1920×1080p@30 fps

1.0 lux(COLOR), 0.1 Lux(B/W)

BNC (AHD / CVBS Selectable)

OSD Menu (Coaxial control)

More than 50dB (AGC off)

MANUAL

AUTO, 1/60, FLK ~ 1/50,000 sec

1 ~ 15

OFF / AUTO (x2, x4, x6, x8, x10, x15, x20, x25, x30)

1 ~ 100

OFF / ON / AUTO

OFF / AUTO

OFF / BLC / HSBLC

ATW / AWC / INDOOR / OUTDOOR / AWB

AUTO / COLOR / B&W

OFF / LOW / MIDDLE / HIGH

OFF / LOW / MIDDLE / HIGH

OFF / ON

OFF / FREEZE / MIRROR / NEG.IMAGE

OFF / ON (4 zone)

OFF / ON (4 zone)

ENG / CHN1 / CHN2 / GER / FRA / ITA / SPA / POL / RUS / POR / NED / TUR / KOR / JPN / HEB / ARB

LIVE DPC / WHTE DPC / BLACK DPC

OFF / AUTO (0 ~ 10)

CRT / LCD

OFF / ON

NTSC / PAL

SAVE & EXIT / NO SAVE / RESET

DC JACK

BNC Connector (AHD / CVBS)

Over 500m via 5C-2V coaxial cable

Fixed mount

f=4.3mm F2.0 Megapixel Fixed Pin Hole Lens

14°F ~ 122°F (-10 ℃ ~ +50 ℃ )

0 ~ 90% (non-condencing)

55.0mm x 872.6mm x 31.5 (44.45mm Inclusion bracket)

Unit : 1.36kg, Shipping : 2.0kg

21

Height Strip Covert Camera

PRINTED IN KOREA

50304 267A