Buffalo TS-0.6TGL, TS-1.0TGL, TS-1.6TGL, TS-2.0TGL User Manual
Add to my manuals
74 Pages
Buffalo TS-2.0TGL is an advanced network storage device aimed at small offices and branch offices that allows to set up a private cloud to store, access, and share files from anywhere. Its user-friendly interface helps you easily configure and manage the device, even if you don't have any prior IT experience. The TS-2.0TGL is well-suited for small businesses that need a reliable and affordable way to store and share files, collaborate on projects, and back up their data. Here are some of the key benefits and use cases for the Buffalo TS-2.0TGL:
Centralized storage: The TS-2.0TGL provides a central location for storing all of your important files, making it easy to access them from any computer or device on your network. This can be especially helpful for businesses that need to share files between multiple employees or departments.
advertisement
User Manual
TeraStation Pro
TS-TGL/R5
www.buffalotech.com
v2.2
Introduction
Congratulations on your new TeraStation! This user manual is intended to assist you in configuring it.
Because we’re constantly updating our product, the images and text in this manual may vary slightly from the images and text displayed by your TeraStation. These changes are minor and should not affect the ease of setup adversely. As time passes, future user interfaces, updated software, and later versions of this manual may be freely available for download at our web site: http://www.buffalotech.com
.
If you run into difficulties or need additional help, feel free to contact our 24/7 Technical
Support at (866) 75-610 (USA & Canada only). Technical Support in Europe is available between the hours of 9am - 6pm (GMT) Monday through Thursday and 9am-4:30 pm
(GMT) Friday for this product. Customers in Europe can obtain Technical Support using the following information: Email: [email protected]
| Web: www.buffalotechnology.com.
Table of Contents
TeraStation Quick Setup ...................................................
4
TeraNavigator Setup..........................................................8
Accessing TeraStation Data from a PC .............................15
Accessing TeraStation Data from a Mac...........................
17
TeraStation Diagram .......................................................21
Advanced Settings ...........................................................
24
Basic Settings .................................................................25
Network Settings .............................................................26
Disk Management ...........................................................28
Adding Extra Hard Drives ...............................................
34
Shared Folders ................................................................
38
Groups ...........................................................................
42
Users ..............................................................................
43
Troubleshooting Multiple Shares..................... ................
45
Backups .........................................................................47
Maintenance Settings ......................................................51
UPS Settings ...................................................................52
System Information .........................................................58
Client Utility ...................................................................
64
Troubleshooting ..............................................................66
Changing Hard Drives .....................................................68
Technical Specifications ..................................................
72
Technical Support ...........................................................
73
Begin setting up your TeraStation by plugging your power cable and Ethernet cable into the back of the TeraStation as shown.
TeraStation Quick Setup
Connect your cables
TeraStation Quick Setup
Plug the power cord into a 120 volt wall socket.
Plug the other end of the Ethernet cable into a hub, router, or switch in your network.
5
TeraStation Quick Setup
Press the power button on the front panel. LEDs will light as your TeraStation boots up.
After your TeraStation has completed booting up, check the
LINK/ACT LED on the front of the TeraStation. If it’s lit, then your TeraStation is connected properly, and you can go on to page 8. If it’s not lit, turn to page 7 for troubleshooting.
6
TeraStation Quick Setup
The TeraStation’s Ethernet port will automatically adjust to use either a Crossover or Patch cable, so you may connect the TeraStation to your network with either type of Ethernet cable. Buffalo
Technology doesn’t recommend connecting the TeraStation directly to a PC.
Verify that the LINK/ACT LED on the front of TeraStation is lit (see page 6’s picture). If it’s lit, go to page 8 to continue setting up TeraStation. If the LINK/ACT LED is still not lit, try the suggestions below to verify that you’re not suffering from common setup problems.
Having problems? Make sure that:
• the TeraStation and the router, hub or switch are both powered on,
• the Ethernet cable is securely plugged in at both ends, and
• the Ethernet cable is not damaged. Verify this by trying a different Ethernet cable.
If problems persist, c ontact our 24/7 technical support at (866) 75-610 (USA & Canada only).
Technical Support in Europe is available between the hours of 9am - 6pm (GMT) Monday through
Thursday and 9am-4:30 pm (GMT) Friday for this product. Customers in Europe can obtain
Technical Support using the following information: Email: [email protected]
| Web: www.buffalo-technology.com
7
TeraNavigator Setup
Insert the TeraNavigator CD into your PC’s CD-ROM drive. Setup should automatically launch. If it does not, manually launch setup.exe by pressing the Start menu and selecting the Run... option.
When the Run dialog opens, type d:\setup.exe
(where d is the drive letter of your CD-ROM drive).
Press OK to continue.
8
TeraNavigator Setup
TeraNavigator should now be running. Press the Install Client Utility button, and then press the
Start button. Once the installation has completed, press the Launch button.
TeraNavigator Setup
The TeraStation Client Utility allows you to easily configure TeraStation’s network settings. The tabs show the names of available TeraStations. If you have more than one TeraStation on the network, click the tab of the one you want to select it. While a TeraStation’s tab is selected, its
IP Address is visible and the View Shares button will take you directly to its network shares and folders. See page 64 for more information on the TeraStation Client Utility. For now, make sure that the proper TeraStation’s tab is selected, click Setup from the pull down menu, and choose
Browser Management .
10
TeraNavigator Setup
This login prompt will appear. Enter admin for the user name. Until you change it, the password for the admin account will be password . Press the OK button when finished.
User name: admin
Password: password
See page 44 to change your password.
If this login prompt does not appear, your DHCP server may not be functioning correctly. If DHCP is disabled, you may re-enable it, or verify that the TeraStation’s IP Address (page
10) is in the same range as that of your
PC.
NOTE: Pages 64 and 65 describe how to configure the TeraStation with a
Static IP Address.
11
TeraNavigator Setup
You are now logged in to the TeraStation Management Utility. Bookmark this page in your browser so it can be easily accessed for future configuration changes. If the TeraStation’s IP Address changes, you will need to recreate this link. You can also get here by typing http://TERASTATION_
NAME into a Web browser, where TERASTATION_NAME is the name of your TeraStation that you set on page 13. For detailed explanations of each menu and setting, please refer to the Advanced
Settings section, starting on page 24 of this manual. To continue setup, click on the Basic link on the left side.
1
Here on the Basic page, begin by changing the name of your TeraStation in the TeraStation
Hostname field. A friendly, easy-to-remember name (such as “TeraStation”) is recommended.
The name cannot contain any spaces or special characters. Alphanumeric characters, hyphens, and underscores are allowed.
A short description of the TeraStation can be entered into the TeraStation Description field.
You’ll then see this description in Network
Neighborhood on Windows machines.
Make sure that the date and time are correct in Date and Time Setup . To synchronize clock settings with your computer, press Use Local
Time .
Once desired fields have been completed, press the Apply button at the bottom of the page.
For more information on the Configuration
Utility, turn to Advanced Settings , beginning on page 24.
1
TeraNavigator Setup
TeraNavigator Setup
Congratulations! You’ve completed basic setup. For more detail on the other settings available in your TeraStation, turn to Advanced Settings , beginning on page 24.
To Access TeraStation Data on a PC:
Press the Start menu, select the Run...
option. When the Run dialog opens, type \\TeraStation_
Name (where ‘TeraStation_Name” is the TeraStation Hostname set on page 13). Press the OK button to continue.
1
Accessing TeraStation Data from a PC
TeraStation’s root directory will appear. You will see all of the configured shares, including share , the preconfigured data folder. All users can read and write to all folders unless otherwise configured.
To set up security and password protection, or add other shares to your TeraStation, please refer to pages 38 - 39 of this manual. To change your RAID configuration, see pages 29 - 30. Drive letters can also be mapped to shares on your TeraStation; see page 16 for more information.
Note: If this page does not appear, or if you receive a popup window from your firewall saying that a NetBios
Session has been blocked from your TeraStation’s IP
Address, you will need to add your TeraStation’s IP
Address to your firewall’s trusted zone. You can get your TeraStation’s IP Address from the TeraStation
Client Utility (see page 10). Consult your firewall documentation for more information on allowing network access to and from a specific IP Address.
15
Accessing TeraStation Data from a PC
From the TeraStation’s Root Directory screen (see page 15), click the Tools pull down menu and select Map Network Drive ; Map Network Drive will run. Select the drive letter you would like to map from the Drive: pull down menu. Enter \\TeraStation_Name\share_name in the Folder: field, where TeraStation_Name is the TeraStation Name set on page 13 and share_name is share (if you’re mapping to this preconfigured folder) or the name of another shared folder that you set up on page
38. You may browse for a shared folder by pressing the Browse button and searching through the
Entire Network and then the Microsoft Windows Network.
Check the Reconnect at logon checkbox to have Windows connect to this mapped drive everytime it starts. When finished, press the Finish button. TeraStation is now mapped to a drive letter.
16
Accessing TeraStation Data from a Mac
If your Mac does not automatically detect your
TeraStation’s Share folder and put it on your desktop, you will need to add the TeraStation to the Mac’s server list. Begin by clicking Go , and then choose Connect to Server .
17
In the Server Address field, enter your
TeraStation’s IP address in the form smb:\\ ipaddress (where “ipaddress” is your
TeraStation’s IP address), and click Connect .
If you don’t know your TeraStation’s IP address, see page 19.
Accessing TeraStation Data from a Mac
Select Guest and click on Connect . Note: If you have configured share permissions on your TeraStation, select Registered User and enter your
Registered User credentials.
Select the volume that you want to mount, such as share or share-mac , from the list of folders on the TeraStation.
The share will open. A link to the shared folder will appear on your desktop.
18
Accessing TeraStation Data from a Mac
If you don’t know your TeraStation’s IP address, there are several ways to get it.
One simple method is to use the TeraStation client utility
(included on your CD) to find your TeraStation(s). Just click on the tab for your TeraStation and you’ll be able to read its
IP address. You must have a Windows PC running on the network to use the TeraStation client. See page 64 for more on the TeraStation client utility.
You can get the TeraStation’s IP address from the LCD display on the front of the TeraStation as it boots up.
You can always get the TeraStation’s IP address from your router’s configuration utility. Many Buffalo routers list this information on the Client Monitor page, as shown to the right.
Consult your router’s documentation for instructions on identifying the TeraStation’s IP address.
1
TeraStation Expansion
TeraStation Pro has two USB 2.0 ports on the rear. These ports can be used for adding external
USB Hard Drives or UPS systems. TeraStation will share connected USB storage devices, allowing everyone on the network to use them. Up to two external USB hard drives may be added to
TeraStation Pro. To connect a USB hard drive or UPS to TeraStation, simply plug it into one of the
USB Ports.
You may plug in additional USB hard drives to either of the USB ports on your TeraStation. See page 34 for setting up your USB hard drive on the TeraStation. See page 38 for information on setting up shared folders on a USB Hard Drive. Page 37 will show you how to reformat the USB
Hard Drive. Page 47 shows you how to set up TeraStation to backup to a USB Hard Drive.
See pages 52 and 53 for more information on using the TeraStation with a UPS.
0
Power Button – Press and release the Power Button to turn the TeraStation on. Hold it down for three seconds to turn the TeraStation off.
Hard Drive Access – The Access LEDs will blink green when the associated hard drive is accessed.
During startup, it’s normal for all the lights to blink.
Hard Drive Cage – The tubular lock prevents physical access to hard drives when locked. See page 68 for information on replacing hard drives.
TeraStation Layout
1
The Status LCD can be configured to display specific TeraStation information.
Please see page 55 to configure the various display options.
TeraStation Layout
TeraStation Layout
UPS interface – An Uninterruptable Power Supply can use this serial port to safely shut down your TeraStation in the event of a power failure.
This interface is non-LPS. DP-1, DP-1P, DP-2, or DP-2P cables may be used to connect to the UPS. The TeraStation Pro also supports many USB
Uninterruptable Power Supplies.
10/100/1000 Mbps Ethernet Port – Use this port to connect your
TeraStation to a switch, a router, or another computer. The port is autosensing, so either a conventional Ethernet cable or a crossover
Ethernet cable may be used.
USB Ports – TeraStation offers two USB 2.0/1.1 ports for adding external drives or UPSs. Please see the TeraStation Expansion section on page 20 to learn more about using TeraStation’s USB Ports.
Browser Management Tool - Home
Advanced Settings
Welcome to Advanced Settings ! We’ll discuss the many adjustments you can make to your TeraStation.
Begin by bringing up the Browser
Management screen that you bookmarked on page 12. You are now at Home . Notice that Home is lit up in yellow in the screenshot to the left. You can return to this page at any time by clicking on Home from the menu at the left of your Browser
Management screen. Here, you can see basic information about your
TeraStation’s setup. If you have lost your TeraStation, clicking I’m here!
at the bottom left will cause it to beep, making it easier to find. For now, click the Basic link from the menu on the left side of your screen.
Basic
You may modify your TeraStation’s hostname and description under Hostname Setup .
Make sure that the date and time are correct in Date and Time Setup . To synchronize time settings with those in your computer, press
Use Local Time . To have your system time automatically set by an NTP server, enable NTP
Server and enter an IP Address for the NTP server (e.g. 192.43.244.18) or use the supplied default NTP server.
Ensure that both the Display Language and the
Windows Client Language are set to languages that you’re comfortable with.
Once desired fields have been completed, press the Apply button.
5
Advanced Settings
Network (IP Address Properties)
Advanced Settings
In most networks, TeraStation will get its IP
Address automatically from a DHCP server.
You may disable DHCP here. If DHCP is disabled and an IP Address is not set manually, it will default to 1.168.11.150
. The
TeraStation’s IP Address , Subnet Mask , Default
Gateway Address , and DNS Server address may all be entered manually under IP Address
Properties .
Ethernet Frame Size may also be set manually on this page. Only use JumboFrame settings when operating in a Gigabit environment where all other clients support the same JumboFrame setting.
Click Apply after making any changes.
6
Advanced Settings
Network (Workgroup/Domain)
If you are unfamiliar with Domain/Active Directory networking, then please leave the Network Type selected as
Workgroup and Workgroup Name set to Workgroup .
To make your TeraStation a member of a workgroup or domain, enter the appropriate information into the fields on this page and click Apply . Do not select Domain unless you have a Windows Server Domain Controller on your network. Please leave the network type selected as
Workgroup unless you are a network administrator or have been instructed to do so by one.
NOTE: If using Domain , TeraStation must be added as a member computer in the Domain Server.
Domain & Active Directory Authentication integrates the TeraStation Pro with Windows Domain and Active
Directory Servers. The TeraStation Pro participates as a member device in the Domain and Active Directory networks, allowing the TeraStation to use Users and Groups that reside on the Domain or Active Directory
System. If Active Directory is used, then the TeraStation will automatically receive update information from the domain controller(s). To configure the TeraStation Pro on an Active Directory network, you must have the Domain Administrator login credentials. To configure TeraStation Pro in a Windows Domain or Active
Directory environment, please select Domain as the Network Type. Enter the Domain Name and Domain
Controller into the appropriate fields. In an Active Directory environment, check the Active Directory Domain checkbox and fill in the remaining fields. The Authentication Setup fields will be automatically filled out, so no input is needed there. Once you have finished, press Apply .
7
Disk Management (Drive Properties)
This page shows the current properties of your hard drives and RAID Arrays. To change these settings, click on RAID
Configuration at left.
Advanced Settings
8
Note on RAID Arrays
TeraStation uses RAID (“Redundant Array of Independent Disks”) technology to control the four hard drives in your TeraStation. RAID may be configured several ways:
RAID Spanning - All four drives are striped into one large drive, giving the maximum capacity for your TeraStation. This size is the one listed on your TeraStation’s box and shows the total capacity of the TeraStation with no data used for redundancy. RAID Spanning is fast and efficient, but with no redundancy, if one hard drive fails, all data on the TeraStation is lost.
RAID 1 (mirroring) - Hard drives (or spanned pairs of hard drives) are arranged in mirrored pairs.
Each half of the pair reads and writes exactly the same data. This costs you half the total capacity of your TeraStation, but provides excellent redundancy. If a hard drive fails, the mirror continues to supply data, so you may work on normally. You may replace the damaged or defective drive at any time, and normal RAID 1 mirroring will then be automatically restored.
RAID 5 (parity) - All drives in a RAID 5 array reserve part of their data space for parity information, allowing all data to be recovered if a single drive fails. The parity information takes up about one hard drive’s worth of space, so if you set up all four drives in the TeraStation as a RAID 5 array, your usable capacity will be about 3/4 of the total capacity of the TeraStation. RAID 5 is an excellent compromise between efficiency and security. If a single drive fails, no data is lost. After the damaged or defective drive is replaced, your TeraStation will automatically restore all data to the new drive and resume normal RAID 5 operation. This is how your TeraStation is set up out of the box.
Buffalo Technology recommends RAID 5 for its excellent balance of efficiency and security.
Advanced Settings
Disk Management (RAID Configuration)
This page shows your current RAID arrays. You may delete old arrays or create new ones by clicking on the underlined
RAID Array # under RAID Array Configuration .
The RAID Scanning Settings set a specific time for the
TeraStation to scan and inspect its RAID arrays. It is recommended to set a time where the TeraStations usage will be minimal (perhaps the middle of the night). TeraStation will be significantly slower while the RAID scan occurs.
Begin Immediate RAID Scan specifies the TeraStation to run a RAID Scan immediately after pressing Apply.
You may also disable RAID Array Error Detection Response from this page. Normally, this is set to automatically shut down the RAID array when an error is detected. Though it is not recommended, you may disable that behavior by selecting Disable .
NOTE: TeraStation has four internal hard drives. Before creating a new RAID array, you may have to delete one or more pre-existing RAID Arrays to clear up the hard drives for your new one. This will destroy all data currently on the disks, so back up any important data before deleting RAID arrays. Whether you want to clear out an old array or create a new one, begin by clicking on the array’s underlined RAID Array # , under Name .
0
Disk Management (RAID Configuration)
A configured RAID array may be deleted by pushing the Delete RAID Array button. This will free up all hard drives listed under Disk Structure.
Advanced Settings
To configure an unconfigured array, put checks next to the hard disks you want included in the array
(under Disk Structure ) and choose your RAID mode .
Click Setup RAID Array when ready. It may take several minutes to complete setting up the RAID array. When it’s finished, a Disk Scan will run, this may take several hours to complete; performance will be slow during the Disk Scan.
1
Disk Management (Disk Check)
Advanced Settings
When RAID Configuration is done, you’ll see this screen. To configure a new array, click on RAID Array # and go back to the bottom of page 31. To set up shares, turn to page 8.
Advanced Settings
Disk Management (RAID Configuration)
You’ll see this screen when your new RAID
Array is completely configured. Click on
Shared Folders and turn to page 38 to begin setting up shares on your TeraStation.
Disk Management (USB Settings)
If you’ve plugged an external USB hard drive into one of the USB ports on your
TeraStation, you may set it up from this page. Click on its name under USB Disk
Setup to begin.
Advanced Settings
Advanced Settings
Disk Management (USB hard drive setup)
From here you can see your USB hard drive’s setup information. If the hard drive’s information isn’t displayed properly, try restarting your USB hard drive and then restarting your TeraStation. Some USB hard drives must be reformatted from within
TeraStation before they can be assigned shares. Press Format USB Disk , or choose
Disk Format from the left-side menu, to begin reformatting your USB hard disk. Turn to page 37 for more information on reformatting disks. Turn to page 38 to set up shares on your USB hard drives.
5
Disk Management (Disk Check)
Advanced Settings
To initiate a comprehensive disk check on a hard drive or array of drives, select the hard drive or array that you want to check from the Target Disk dropbox and click the Select Target button.
Performance will be slower while the disk check is running.
6
Advanced Settings
Disk Management (Disk Format)
To format a hard drive or array, select it from the Target Disk drop box. Choose the file system desired from the File System dropbox
(internal drives can only be formatted with XFS).
Note that FAT32 has a 2 gigabyte single file size limit. If you choose FAT32 for your file system, you will not be able to store single files larger than 2 gigabytes on the drive. Use of the XFS or
EXT file systems is recommended. Press Select
Target Disk when done.
Depending on the size of the target hard disk or array, a Disk Format may take several hours to complete. Performance will be slow during the disk format.
7
Advanced Settings
Shared Folders
To begin setting up shares on your TeraStation, select Shared Folders from the left side menu, and then click the Add button under Shared Folders Setup .
To delete a share or shares, check the checkbox next to the shares you’d like to delete, and press the Delete button. Deleting shares will remove the share and erase all of the files and folders inside that share.
8
Advanced Settings
Add a new Shared Folder
To add a new shared folder, enter a name for it in the Shared Folder Name box and choose which Disk Space it will reside in. You may also choose which operating systems and features the share will support by putting the appropriate checks next to Shared Folder
Support , and whether the share supports the
Recycle Bin by putting a selecting Enable or
Disable . Enter a Shared Folder Description and a Remote Backup Password if desired. Click
Apply to build the new shared folder.
Appletalk support is available for use with legacy Macs. Checking “Apple” by Shared
Folder Support lets you use your TeraStation with older Macs, but gives you all of Appletalk’s limitations, including a 2GB maximum filesize and a 32 character limit for filenames. For OS X 10.3.9 and later, leave “Apple” unchecked for best performance.
Remote Backup Password will set a password on this share for other TeraStations who want to use it as a remote backup target. This password will not affect users attempting to access the share; it only pertains to remote TeraStations trying to access this share for backup tasks.
Advanced Settings
Shared Folders (Access restrictions)
0
To use Access Restrictions for a share, select
Enable .
Highlight groups or users in the All Groups/
Users column and use the left-pointing arrow buttons (located just to the left of each box) to move individual groups or users from the All
Groups/Users column to the Read Only box (if you want to give them read access only) or all the way to the Writable box, if you want to give them full access to the share. Right-pointing arrows will move highlighted users or groups back to the right.
Click Apply when you have your groups and users in the appropriate boxes.
To set up new groups and users, see pages 42 and 43.
Advanced Settings
Shared Folders (Service Setup)
To allow FTP Access to TeraStation, choose Enable for FTP Server . To enable legacy AppleTalk support, choose Enable for AppleTalk Protocol .
FTP Server Info: Enabling the FTP Server will allow users to connect to shares via FTP protocol.
Their username and password is used for their login credentials, and they will only have access to shares that have read-only or writeable access to on the TeraStation. The network administrator of your network may need to enable traffic on port 21 to the TeraStation for FTP to work over the
Internet.
Click the Apply button to set up these services.
1
Advanced Settings
Group Management
Add a name and a description to the Add New
Group fields. Put checks next to each Member User that you want to be part of the group. Click Apply when your group is set up the way you want it.
Active Directory and Domain Groups are not shown here but are available under Share Management.
Members can be added or removed from a group at any time by editing the group. This is done by clicking on the Group name on the main Group
Settings page.
Groups allow for easier management of permissions in some networks, specifically networks with a lot of users in different departments.
To Delete a group, put a check next to its name and click Delete . To add a group to your TeraStation, click Add .
User Management
The Add New User dialog will appear. Enter a
User Name , Password , and User Description for the new user and click the Apply button. If a user will be accessing the TeraStation from a Windows
95/98 computer, their password should be 15 characters or less. Mac OS 8 and OS 9 users’s passwords should be 9 characters or less.
A Domain User List will be displayed if the
TeraStation Pro is a member of a Domain or
Active Directory environment.
Advanced Settings
TeraStation is preconfigured with two users, admin and guest , out of the box. The admin and guest user accounts cannot be deleted. To delete any other user, put a check next to their name and click Delete . To add a new user, click
Add .
Advanced Settings
User Management (changing passwords)
To change an account’s password, click on the name of the account under User Settings . Note: if a user name and password are used to log into a user’s windows computer or domain, the same user name and password should be used when creating the user’s account on the TeraStation, or problems accessing shared folders may occur.
Enter the desired new password in both boxes and click Apply .
Advanced Settings
Troubleshooting Multiple Shares
When accessing multiple shares to a Windows
PC, you may see this error message.
This is caused by having multiple shares to the same resource using different login credentials.
The error occurs when connecting to at least one secure, restricted share. Due to a constraint in
Microsoft Windows, only one set of login credentials can access or map drive letters for a network resource such as the TeraStation. As such, only one username and password can be used while mapping drives to a PC. If unsecure, unrestricted shares are mapped and then an attempt to map a secure, restricted share is made from the same PC, then this error will occur. To prevent this, you must create all mapped shares using the same login and password information. Please follow the steps on the next page to remedy this problem.
5
Advanced Settings
Mapping Multiple Shares
When mapping any share, select the Connect using a different user name option. A login and password prompt will appear.
Use the username and password required by any secure, restricted shares for all shares. All mapped shares on a single PC must use the same username and password!
If only unrestricted shares are being mapped, then it’s not necessary to set a username and password for shares. Multiple mapped drives to unrestricted shares can exist without a username or password as long as no restricted, secure shares are mapped. If an unrestricted share and a restricted share are being mapper or accessed, use the restricted username and password for the unrestricted share login by using the Connect using a different user name option. This will allow a
Windows PC to access both shares without any problems.
6
Disk Backup
Advanced Settings
To create a backup job, click on a Job Number .
The Edit Backup Job dialog will appear.
7
Disk Backup (Edit Backup Job)
8
Advanced Settings
A Backup Job can run regularly on a daily or weekly schedule, or immediately by appropriate choices in the Backup Job Schedule field. Date and Time for the backup may be entered, and Encryption and Compression enabled or disabled. Enable Overwrite Backup to have each scheduled backup write over the previous backup, or Differential Backups to backup only files changed since the previous backup.
Select the folder to be backed up from the
Local Backup Shared Folder dropbox, and the destination for the backup files from the
Destination Backup Shared Folder dropbox.
The destination folder may be on a USB drive attached to the TeraStation, or another
TeraStation on the network. Click on Select to approve the backup targets.
Click the Apply button when your backup job is set up the way you want it, or Clear Job to stop a job from running again.
Disk Backup (TeraStation List)
Advanced Settings
The TeraStation list shows other TeraStations in your network that you can configure network backups to.
Press Refresh to get a list of TeraStations on your network.
Disk Backup (Add TeraStation)
Advanced Settings
To add a remote TeraStation to your network, enter its numerical IP Address in the Remote
TeraStation IP Address field and click the Add to List button. For remote TeraStation backups, make sure both firewalls are configured to allow traffic in and out of their networks.
Note: Disk Backups between two TeraStations use port 8873 for encrypted backups and port 873 for backups with no encryption.
50
Maintenance (Notification)
Advanced Settings
If your TeraStation is remotely managed, you may choose to receive nightly status reports and be notified of any disk events by email.
To set this up, enable Mail Notification and enter the IP Address of your SMTP server* in the SMTP Server Address field. Select a
Subject line for the emails (i.e. “TeraStation
Status Report”) and enter the email address of each person you want to receive notification emails into a Recipient Mail Addres s field.
* SMTP server must be an open type server. Currently, there’s no provision for entering a username or password.
51
Maintenance (UPS Settings)
Advanced Settings
You may enable Synchronize with UPS and
UPS Shutdown Conditions from this page.
Consult your Uninterruptable Power Supply’s documentation for further information about setting up your UPS system.
Buffalo Technology recommends the use of
APC SmartUPS Serial Uninterruptable Power
Supplies. Other UPSs may use different pin configurations. Compatibility cannot be guaranteed with other UPSs. See page 53 for more on the TeraStation’s UPS serial port.
5
Maintenance (UPS Settings)
Advanced Settings
This is TeraStation’s serial port pin assignment for serial UPS products.
5
Maintenance (Alert Settings)
Advanced Settings
Alerts can be configured on the TeraStation to make audible noises when a problem is detected.
Along with the audible noise, alert emails will be sent out if Mail Notification was properly configured.
Please select the features you would like to receive an audible sound alert from and then press the
Apply button.
5
Advanced Settings
Maintenance (Status LCD)
The Status LCD Setup allows configuration for the LCD display on the front of TeraStation. Please select the type of information that the front panel should display from the LCD Display Items .
Automatically Switch LCD Items tells the TeraStation to cycle through the selected display items every 10 seconds. Disabling this feature means the LCD display does not cycle, and it will stay on the same display item until the Display button on the front of TeraStation is pressed. The LCD screen and green LED buttons brightness can be controlled via their respective settings. Press the
Apply button once all of the settings have been configured.
55
Advanced Settings
Maintenance (Shutdown)
From the Shutdown page, press Apply to shutdown TeraStation. This has the same function as holding down the power button on the front of TeraStation, but may be done remotely. Turning on the TeraStation after a shutdown requires a physical button push on the front of TeraStation.
The Restart Now button simply reboots the TeraStation, bringing it back to functionality after about 120 seconds.
56
Advanced Settings
Maintenance (Initialization)
Initialization is a reset procedure that restores all settings back to the default, out of box, configuration. All configuration, users, groups, and backup jobs are lost, but actual data and shares on the hard are NOT lost. If you want all data to be erased, reformat the drive.
Specify whether the TeraStation shall keep its administrator password after a initialization or whether the password should be reset to the default password (default password is password ). Press the Apply button once you make the selection.
Press the Restore button to begin the initialization process; this will restore all settings to factory defaults but will NOT erase the data on the hard drives. Start Disk Formatting begins a complete disk format that will erase all information on the TeraStation’s internal hard drives. This cannot be undone.
57
System Status (System Information)
This page shows you the System Information for your TeraStation.
Firmware updates are occasionally available from www.buffalotech.com
for the TeraStation Pro.
These must be executed from a Windows PC on the same network. Your router, switch, or hub should pass through ports 8873 and 22939 for this to work (most do).
58
System Status (USB Details)
Advanced Settings
This page shows you details on USB hard drives and UPSs plugged into your TeraStation.
5
System Status (Drive Properties)
This page shows you the properties of all hard drives and
RAID arrays in and attached to your TeraStation.
60
Advanced Settings
System Status (Network Information)
Advanced Settings
This page shows you the System Information for your network connection.
61
System Status
User Access Status
This page shows you the current status of all active users on the TeraStation. It also shows users connected remotely via the FTP Server.
6
System Status
Log Information
This page displays system log information. Choose from the available variables and press the Select button to show you the logs for the variables you selected.
6
6
TeraStation Client Utility
This is the TeraStation Client Utility . Installed on your PC, it allows you to access each of the
TeraStations on your network. Click Refresh
List to get tabs for each of your TeraStations.
Each tab shows the Host Name, Workgroup, IP
Address, and Subnet Mask of the associated
TeraStation, as well as the version of firmware it’s running.
With a TeraStation’s tab selected, you can click on the View Shares button to go directly to its root share. Clicking the Setup pulldown menu and selecting Browser Management takes you to the browser management tool that we began exploring on page 24. And clicking Setup and choosing Modify IP Address takes you to the following screen . . .
TeraStation Client Utility
IP Address Setup
Here, you may enter your IP Address and Subnet Mask manually, or enable your TeraStation to acquire them automatically from a DHCP server. You’ll need the administrator password to use this screen. Press OK when you’re done.
65
Troubleshooting
If TeraStation encounters a disk error, it will be reported in the TeraStation status on the top of any of the Web-Based configuration screens. Run a Disk Scan in the event of this error. If that does not resolve the problem, a format is recommended. Formatting the drive will delete all of the data on it, so back up any data you can before formatting. Finally, if none of the above solutions help, then please contact Technical Support (see pages 73 and 74 for Technical Support contact information).
66
Troubleshooting
DIAG LCD Codes:
Error Code
E00
E01
E02
E03
E04
E10
E11
E12
E13
E14
E15
E16
E17
E18
E19
E20
E21
E22
E23
Discription
Error on DRAM ADDRESS LINE
Error on RTC CHIP
Failed to load kernel (FLASH error)
MPU error: Main MPU is not responding.
Error on DRAM DATA LIN
UPS AC LINE FAIL Error
FAN Error: Fan rotation speed is low or fan is stopped.
Alert Sound
A
A
B
B
B
B
A
B
A
A
Cooling Error: Cooling by fan cannot catch up.
Error has occurred on RAID Array x.
Cannot mount RAID Array x.
- (Not Used)
Cannot found HDDx.
Cannot communicate with RTC chip(IC12).
Cannot communicate with SATA chip(IC1).
Cannot communicate with SATA chip 2(IC2)
Cannot communicate with USB chip(IC5)
Cannot communicate with Ethernet chip(IC13)
Cannot mount HDDx
HDDx faulty (HDDx is excluded fom raid because of errors)
B
B
A
A
A
A
B
A
67
Replacing a Hard Drive
Turn the key counter-clockwise to open drive door.
Squeeze the tabs gently and swing the tray latch upward.
The hard drive tray will now slide out.
68
Lower the drive carefully to the work surface.
Gently push down on the two tabs to release the plug.
6
Pull the plug straight out to remove the drive.
To remove the hard drive from its cage, set the assembly on a soft surface and remove these four screws.
70
Install a new hard drive by doing the same steps in reverse order:
Begin by screwing the new hard drive into the cage.
Plug the power/data connector into the hard drive.
Slide the hard drive cage back into the TeraStation.
Press the latch down to lock the hard drive cage in place.
71
LAN Standards:
Transmission Types:
Access Media:
Media Interface:
USB Standard:
USB Connector:
Data Transmission Speed:
UPS:
Power Consumption:
Dimensions:
Weight:
Operat ing Environment:
Technical Specifications
7
IEEE 802.3u 100BASE-TX; IEEE 802.3 10BASE-T
1000Mbps/100Mbps/10Mbps; 100BASE-TX
4B/5B, MLT-3;10BASE-T Manchester Coding
CSMA/CD
RJ-45
USB 2.0
Hi-Speed (HS)
Full-Speed (FS)
Low-Speed (LS)
USB A Connector (2)
Max: 480 Mbps (HS Mode)
Max: 12 Mbps (FS Mode)
UPS Compatible (Serial/USB connection)
~56W (Varies based on size)
6.7” x 9.3” x 12.2” (170 x 235 x 310 mm.)
~15.8 lb. (7.2 kg.) (Weight varies based on size)
32° - 95° F; 20-80% non-condensing
Technical Support (US and Canada)
Buffalo Technology offers toll-free technical support 24 hours a day, 7 days a week for this product.
Customers in the United States and Canada can obtain technical support using the following information:
Web:
E-mail:
Telephone: www.buffalotech.com
(866)-75-610 (USA & Canada only; see page 74 for European tech support)
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
GPL Statement
This product uses GPL/LGPL software. Please see the GNU LICENSE document on the TeraNavigator
CD-ROM for more information concerning the terms of the license. To obtain a copy of our open source software, contact [email protected].
7
Technical Support (Europe)
Buffalo Technology (Europe), Inc.
176 Buckingham Avenue,
Slough, Berkshire, SL1 4RD
United Kingdom
GENERAL INQUIRIES
Email: [email protected]
TECHNICAL SUPPORT
Technical Support in Europe is available between the hours of 9am-6pm (GMT) Monday to
Thursday and 9am-4:30pm (GMT) Friday for this product. Customers in Europe can obtain
Technical Support using the following information:
E-mail: [email protected]
| Web: www.buffalo-technology.com
7
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project