Apollo

™

MS-RA670 Installation Instructions

Important Safety Information

WARNING

Failure to follow these warnings and cautions could result in personal injury, damage to the vessel, or poor product performance.

See the Important Safety and Product Information guide in the product box for product warnings and other important information.

This device must be installed according to these instructions.

Disconnect the vessel's power supply before beginning to install this product.

Before applying power to this product, make sure it has been correctly grounded according to these instructions.

CAUTION

To avoid possible personal injury, always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding.

NOTICE

When drilling or cutting, always check what is on the opposite side of the surface to avoid damaging the vessel.

Do not use the stereo as a template when drilling the mounting holes because this may damage the glass display and void the warranty. You must only use the included template to correctly drill the mounting holes.

You must read all installation instructions before beginning the installation. If you experience difficulty during the installation, contact Fusion ® Product Support.

What's In the Box

• Mounting gasket

• Four 8-gauge, self-tapping screws

• Two screw covers

• Power and speaker wiring harness

• Auxiliary-in, line-out, and subwoofer-out wiring harnesses

• 2 m (6 ft.) NMEA 2000 ® drop cable

• Dust cover

Tools Needed

• Phillips screwdriver

• Electric drill

• Drill bit (size varies based on surface material and screws used)

• Rotary cutting tool or jigsaw

• Silicone-based marine sealant (optional)

July 2021 GUID-980DCA16-A168-4346-A761-1B2786A5DD83 v5

Mounting Considerations

• You must mount the stereo on a flat surface that provides open airflow around the rear of the stereo for heat ventilation.

• If you are installing the stereo in a location that may be exposed to water, you must mount it within 45 degrees of the horizontal plane.

• If you are installing the stereo in a location that may be exposed to water, add a drip loop to the cable to allow water to drip off of the cable and avoid damage to the stereo.

• If you need to mount the stereo outside a boat, you must mount it in a location far above the waterline, where it is not submerged, and where it cannot be damaged by docks, pilings, or other pieces of equipment.

• To avoid interference with a magnetic compass, you must install the stereo at least 20 cm (7.87 in.) away from a compass.

2 Apollo MS-RA670 Installation Instructions

Mounting the Stereo

NOTICE

Do not use the stereo as a template when drilling the mounting holes because this may damage the display and void the warranty. You must only use the included template to correctly drill the mounting holes.

Be careful when cutting the hole to mount the stereo. There is only a small amount of clearance between the case and the mounting holes, and cutting the hole too large could compromise the stability of the stereo after it is mounted.

Do not apply grease or lubricant to the screws when fastening the stereo to the mounting surface. Grease or other lubricants can cause damage to the stereo housing.

Before you can mount the stereo in a new location on the mounting surface, you must select a location in accordance with the mounting considerations.

1 Adhere the template to the mounting surface.

2 Drill a hole inside the corner of the dashed line on the template.

3 Cut the mounting surface along the inside of the dashed line on the template.

4 Ensure the mounting holes on the stereo line up with the pilot holes on the template.

5 Using an appropriately sized drill bit for the mounting surface and screw type, drill the pilot holes.

6 Remove the template from the mounting surface.

7 Complete an action:

• If you are installing the stereo in a dry location, place the included mounting gasket on the back of the stereo.

• If you are installing the stereo in a location that is exposed to water, apply silicone-based marine sealant on the mounting surface around the cutout.

NOTICE

Do not install the included mounting gasket if you applied sealant to the mounting surface. Using sealant and the mounting gasket may reduce water resistance.

8 If you will not have access to the back of the stereo after installation, make the necessary wiring connections.

9 Secure the stereo to the mounting surface using the included screws .

You should hand-tighten the screws when securing the stereo to the mounting surface to avoid over tightening them.

10 Snap the screw covers in place .

Connection Considerations

For the stereo to function correctly, you must connect it to power, to speakers, and to input sources. You should carefully plan the layout of the stereo, speakers, input sources, optional NMEA 2000 network, and optional

Fusion PartyBus ™ devices or network before making any connections.

Apollo MS-RA670 Installation Instructions 3

Port Identification

Item Description

Connects the stereo to the wiring harness for zone 3.

Connects the stereo to the wiring harness for auxiliary input 1, and for the line and subwoofer outputs for zones 1 and 2.

Connects the stereo to the power and speaker wiring harness.

FUSE

USB

ETHERNET

ANTENNA

NMEA 2000

Contains the 15 A fuse for the device.

Connects the stereo to a USB source.

SXM TUNER

Connects the stereo to a SiriusXM ® available (not included).

Connect Tuner to receive SiriusXM stations where

Connects to a Fusion DAB module to receive DAB stations where available (not included).

DIGITAL AUDIO IN

(OPTICAL)

Connects the stereo to an optical digital audio source, such as TV or DVD player.

Connects the stereo to another Fusion PartyBus stereo, zone stereo, or network (

Fusion

PartyBus Networking, page 13

).

Connects the stereo to a typical AM/FM antenna.

If you are installing the stereo on a boat with a metal hull, you must use a grounddependent antenna. If you are installing the stereo on a boat with a non-metal hull, you must use a ground-independent antenna. See the installation instructions provided with your antenna for more information.

Connects the stereo to a NMEA 2000 network ( NMEA 2000 System Wiring Diagram, page 12

).

4 Apollo MS-RA670 Installation Instructions

Wiring Harness Wire and Connector Identification

Wire or RCA Connector

Function

Ground (-)

Power (+)

Ignition

Amplifier on

Telemute

Dim

Speaker zone 1 left (+)

Speaker zone 1 left (-)

Speaker zone 1 right (+)

Speaker zone 1 right (-)

Speaker zone 2 left (+)

Speaker zone 2 left (-)

Speaker zone 2 right (+)

Speaker zone 2 right (-)

Zone 1 line out (left)

Zone 1 line out (right)

Bare Wire Color or RCA Label

Name

Notes

Black

Yellow

Red

Blue

Brown

Connects to the power source ( Power Connection, page 7 ).

Connects to the power source ( Power Connection, page 7 ).

Connects to the power source ( Power Connection, page 7 ).

Connects to optional external amplifiers, enabling them to turn on when the stereo turns on.

A connected amplifier must use the same ground (-) as the stereo for this signal wire to function correctly.

Activates when connected to ground.

For example, when you connect this wire to a compatible, hands-free mobile kit, the audio mutes or the input switches to AUX when a call is received and the kit connects this wire to ground. You can enable this function­ ality from the settings menu.

Orange

White

White/black

Gray

Gray/black

Green

Green/black

Purple

Purple/black

ZONE 1

Provides output to an external amplifier, and is associated with the volume control for zone 1.

Apollo MS-RA670 Installation Instructions 5

Wire or RCA Connector

Function

Zone 1 subwoofer out

Zone 2 line out (left)

Zone 2 line out (right)

Zone 2 subwoofer out

Auxiliary in left

Auxiliary in right

Zone 3 line out (left)

Zone 3 line out (right)

Zone 3 subwoofer out

Bare Wire Color or RCA Label

Name

ZONE 1 SUB

OUT

ZONE 2

ZONE 2 SUB

OUT

Notes

Each subwoofer cable provides a single mono output to a powered subwoofer or subwoofer amplifier.

Provides output to an external amplifier, and is associated with the volume control for zone 2.

Each subwoofer cable provides a single mono output to a powered subwoofer or subwoofer amplifier.

AUX IN

ZONE 3

Provides an RCA stereo line input for audio sources, such as a CD or MP3 player.

Provides output to an external amplifier, and is associated with the volume control for zone 3.

Each subwoofer cable provides a single mono output to a powered subwoofer or subwoofer amplifier.

6 Apollo MS-RA670 Installation Instructions

Power Connection

When connecting the stereo to power, you must connect the yellow, red, and black wires to the power source.

The yellow and red wires have different functions, and the method you use to connect them to power depends on how you plan to use the stereo on your vessel.

Yellow wire

• This wire provides power to the stereo.

• This wire should be connected through a 15 A circuit breaker, if one is available on the vessel.

NOTICE

If a 15 A circuit breaker is not available on the vessel, you must connect this wire to power through a 15 A fuse (not included).

• This wire provides power to the stereo at all times, and it will drain the battery even when the stereo is not in use. You should install a manual switch on this wire if a 15 A circuit breaker is not available on the vessel, or if you cannot toggle the breaker to remove power to the stereo when storing the vessel.

• If it is necessary to extend this wire, use 14 AWG (2.08 mm 2 use 12 AWG (3.31 mm ² ) wire.

) wire. For extensions longer than 1 m (3 ft.),

Red wire

• This wire can be connected to the same power source as the yellow wire through the ignition or through a manual switch. This enables you to turn the stereo on and off automatically when you turn the vessel on and off, or when you activate the switch.

• Using this wire to turn the stereo on and off behaves in the same way as using the power button on the stereo to turn it on and off. It is not necessary to connect this wire to a switch if you plan to toggle the power using the power button on the stereo or using a connected chartplotter or remote control. This wire must be connected to turn the stereo on.

•

• When you turn off the stereo using this switch or the power button, it enters a standby mode that allows the stereo to start up again faster than if you switch the power off using the yellow wire. When it is in standby mode, the stereo uses up to 200 mA, and you must turn off power to the stereo on the yellow wire thorough the circuit breaker or manual switch when you are not using the vessel to avoid draining the battery.

NOTICE

You must connect this wire to power through a 1 A fuse (not included), whether or not you connect it to the ignition or manual switch.

• If it is necessary to extend this wire, use 22 AWG (0.33 mm 2 ) wire.

Black wire

• This is the ground wire, and you must connect it to the negative terminal of the power source or to a common ground.

• If it is necessary to extend this wire, use 14 AWG (2.08 mm 2 ) wire. For extensions longer than 1 m (3 ft.), use 12 AWG (3.31 mm ² ) wire.

Apollo MS-RA670 Installation Instructions 7

Connecting to Power Without Using an Ignition Switch

This method of connection is used most often on larger vessels and on vessels with multiple networked stereos and other marine devices. For these installations, a faster startup time is typically less critical, and it is more effective to use the breaker or a dedicated switch on the electrical panel to turn off the stereo and ensure that no unexpected power drain occurs.

1 Consult this diagram to plan the wire connections.

Item Description

Yellow wire

Red wire

1 A fuse (not included)

Manual switch

(optional)

Black wire

Notes

You should connect this wire to the red wire before you connect both wires to the manual switch or circuit breaker.

You should connect this wire to the yellow wire so that it does not act as a physical standby switch.

You must install this fuse on the red wire before you connect the red wire to the yellow wire.

This switch is needed only if a circuit breaker is not available or if it provides a more convenient method of cutting power to the stereo.

Ground (-)

15 A fuse (not included)

This fuse is required if you are not able to connect to power through a

15 A circuit breaker .

15 A circuit breaker If a circuit breaker is not available, you must connect a 15 A fuse on the yellow wire

2 Route all wires to the stereo wiring harness, the circuit breaker or switch, and the power source as necessary.

Do not connect the wiring harness to the stereo until after you have made all of the bare wire connections.

3 Install all of the necessary fuses on the red and yellow wires.

4 Connect the wiring harness to the stereo.

When the circuit breaker or manual switch is closed, the stereo is always on. You can use the power button on the stereo or a connected chartplotter or remote control to place the stereo in a low-power standby mode if needed.

NOTE: When you are not using the vessel, you should remove power to the stereo using the circuit breaker or manual switch to avoid draining the battery.

8 Apollo MS-RA670 Installation Instructions

Connecting to Power Through an Ignition Switch

This method of connection is used most often on ski boats, wake boats, and similar sport or recreational vessels where power to the engines is toggled often. For these installations, a quick standby and faster startup time is desired so that music can be stopped and begin playing again as quickly as possible after restarting the engines. When in standby mode, the stereo uses up to 200 mA, and you should connect the power wires through a circuit breaker or manual switch to avoid draining the battery when you are not using the boat.

1 Consult this diagram to plan the wire connections.

Item Description Notes

Yellow wire

Red wire

1 A fuse (not included)

Ignition or ACC switch

You must connect this wire to the same power source as the ignition or

ACC switch.

You must connect this wire to the ignition or ACC switch before you connect it to the same power source as the yellow wire.

You must install this fuse on the red wire before you connect the red wire to the ignition or ACC switch.

Connecting the red wire to this switch allows the stereo to enter a lowpower standby mode when you turn off the engines, so it can start up faster when you turn on the engines again.

Black wire Ground (-)

15 A fuse (not included)

This fuse is required if you are not able to connect to power through a 15 A circuit breaker .

15 A circuit breaker or manual switch

If a circuit breaker is not available, you must connect a 15 A fuse on the yellow wire. You should also connect the yellow wire to power using a manual switch, so you can remove power to the stereo when you are not using the boat.

2 Route all wires to the stereo wiring harness, the ignition or ACC switch, the circuit breaker, and the power source as necessary.

Do not connect the wiring harness to the stereo until after you have made all of the bare wire connections.

3 Install all of the necessary fuses on the red and yellow wires.

4 Connect the wiring harness to the stereo.

When you turn on the ignition switch, the stereo turns on along with other accessory electronics. When you turn off the ignition switch, the stereo enters a low-power standby mode.

NOTE: When you are not using the vessel for an extended period of time, you should remove power to the stereo using the circuit breaker or other manual switch on the yellow wire to avoid draining the battery.

Apollo MS-RA670 Installation Instructions 9

Speaker Zones

You can group speakers in one area into a speaker zone. This enables you to control the audio level of the zones individually. For example, you could make the audio quieter in the cabin and louder on deck.

Up to two pairs of speakers can be connected per channel of each zone, in parallel. One zone can support no more than four speakers using the on-board amplifier.

Zones 1 and 2 are powered by the on-board amplifier. Zone 3 is available as a line-level output only. To use the

RCA line output and the RCA subwoofer output for zone 3, you must connect an external amplifier.

You can set the balance, volume limit, tone, subwoofer level, subwoofer frequency, and name for each zone, and configure other zone-specific settings.

Single-Zone System Wiring Example

Speakers

Water-tight connection

10 Apollo MS-RA670 Installation Instructions

Speaker System Wiring Using a Line Out

This diagram illustrates a system installation with an external amplifier and subwoofer connected to zone 2 on the stereo using a line out. You can connect an amplifier and subwoofer to any or all of the available zones on the stereo.

NOTE: You can connect speakers to the speaker wires for the internal stereo amplifier while using the line out on zones 1 and 2, although adjusting the volume affects both the speakers connected to the internal amplifier and the line out. This may result in uneven volume levels.

Zone 1 speakers

Water-tight connection

Zone 2 speakers

Amplifier-on signal wire

You must connect this wire to each amplifier connected to a zone line out.

A connected amplifier must use the same ground (-) as the stereo for this signal wire to function correctly.

Powered amplifier connected to the zone 2 line out

Zone 2 line out and subwoofer out

Each subwoofer cable provides a single mono output to a powered subwoofer or subwoofer amplifier.

You may need to use an RCA splitter to connect this to an amplifier.

Subwoofer

Connecting a SiriusXM Tuner Module

This device is compatible with a SiriusXM SXV300 or newer vehicle tuner module.

1 If you have already connected a USB source, disconnect it from the stereo.

2 Connect the cable from the SiriusXM tuner module to the SXM TUNER port on the back of the stereo.

3 Follow the instructions provided with the SiriusXM tuner module and antenna to complete the SiriusXM installation.

4 If necessary, reconnect the USB source.

5 Complete the stereo installation.

Apollo MS-RA670 Installation Instructions 11

NMEA 2000 System Wiring Diagram

Stereo

Supported chartplotter, MFD, or compatible Fusion NMEA 2000 remote control

NMEA 2000 GPS antenna, speed sensor, or wind instrument.

When the stereo is connected to the same NMEA 2000 network as a compatible engine, a GPS antenna, a chartplotter with a built-in GPS antenna, a wind instrument, or a water speed sensor, it can be config­ ured to automatically adjust the volume according to the engine RPM, the speed over ground, the wind speed, or the speed through water. See the stereo Owner's Manual for more information.

In-line switch

NMEA 2000 power cable

NMEA 2000 drop cable, up to 6 m (20 ft.)

9 to 16 Vdc power supply

NMEA 2000 terminator or backbone cable

NMEA 2000 T-connector

NMEA 2000 terminator or backbone cable

12 Apollo MS-RA670 Installation Instructions

Configuring an Optional Wired NRX Remote Control

NOTICE

The stereo is configured by default to work with a NMEA 2000 network, and the NRX POWER option should be enabled only when an optional wired NRX remote control is connected directly to the stereo. Enabling this option when the stereo is connected to a NMEA 2000 network may damage other devices on the NMEA 2000 network.

If you connect an optional wired NRX remote control directly to the stereo, and not through a NMEA 2000 network, additional configuration is needed.

1 Select > SETTINGS > POWER OPTIONS.

2 Select an option:

• If you connected both your stereo and your optional wired remote to a NMEA 2000 network, make sure the NRX POWER option is not selected. This enables the optional remote to receive power from the

NMEA 2000 network.

• If you connected the optional wired remote directly to the stereo through the NMEA 2000 connector, select the NRX POWER option. This enables the stereo to supply power to the optional remote.

Fusion PartyBus Networking

The Fusion PartyBus networking feature allows you to connect multiple compatible stereos together on a network, using a combination of wired or wireless connections.

You can group a compatible stereo, such as the Apollo RA670 stereo, with other compatible stereos connected to the network. Grouped stereos can share available sources and control media playback on all of the stereos in the group, which allows for a synchronized audio experience across the vessel. You can quickly create, edit, and break up groups as needed from any compatible stereo or remote control on the network.

NOTE: A zone stereo, such as the Apollo SRX400, can create or join a group to control and play sources from other stereos, but it cannot share its sources with the group.

For additional considerations when sharing sources, see the owner's manual.

You can use compatible stereos and remote controls, whether they are grouped or not, to adjust the volume of the available speaker zones for any stereo on the network.

Wired Networking Considerations

When you are planning your network installation, observe the following considerations for all wired connections.

• You must connect devices using standard Cat5e or Cat6 network cables with RJ45 connectors.

• You can use one network cable to directly connect two compatible devices.

• You must use wired network switches and wired or wireless network routers when you connect more than two compatible devices to a network.

• If you install a router on the network, it should be configured to be a DHCP server by default. See your router instructions for more information.

• If you do not install a router, and there are no other DHCP servers on the network, you should configure one

Fusion PartyBus stereo to be a DHCP server.

Apollo MS-RA670 Installation Instructions 13

Wired Network Example for Direct Connections

No network setting changes are needed when connecting two devices together directly, but for the best results, you should configure one device to be a DHCP server.

Fusion PartyBus stereo

Fusion PartyBus zone stereo or remote control

Wired Network Example with a Switch or Router

You must use wired network switches, a wired network router, or both to connect more than two devices.

If you did not install a router, and there are no other DHCP servers on the network, you should configure one

Fusion PartyBus stereo to be a DHCP server. If you installed a router, you may need to configure it to be a DHCP server. See your router instructions for more information.

Fusion PartyBus stereo

Wired network switch or wired network router

Fusion PartyBus zone stereo or remote control

14 Apollo MS-RA670 Installation Instructions

Constructing a Network

You should have a basic understanding of networking when building a network for Fusion PartyBus devices.

These instructions guide you through the basics of building and configuring a network, and should apply to most situations. If you need to perform advanced networking tasks, such as assigning static IP addresses to devices on the network or configuring advanced settings on a connected router, you may need to consult a networking professional.

1 Determine the installation location of the Fusion PartyBus devices you want to connect to the network.

NOTE: Wired connections are more reliable than wireless connections. When planning your network, you should run network cables instead of using wireless connections when possible.

2 Determine the installation location of any needed network routers or switches.

3 Route Cat5e or Cat6 network cable to the installation locations of the stereos, switches, and router.

4 Connect the network cables to the stereos, switches, and router.

NOTICE

Do not completely install the stereos yet. You should test the network before you install the stereos.

5 Turn on all devices connected to the network, including wireless devices.

6 If you are using a network router (wired or wireless), consult the documentation provided with your router to configure the router as the DHCP server, if necessary.

All stereos should use their default configuration (DHCP CLIENT).

7 Test the network by selecting > GROUPS to view a list of devices connected to the on the network, and select an option:

• If any devices are not available to the network, troubleshoot the network.

• If all devices are available to the network, complete the installation for each stereo, if necessary.

Network Troubleshooting

If you cannot see or connect to Fusion PartyBus devices on the network, check the following:

• Verify that only one device, either a stereo or a router, is configured as a DHCP server.

• Verify that all Fusion PartyBus devices, network switches, routers, and wireless access points are connected to the network and turned on.

• Verify that wireless Fusion PartyBus devices are connected to a wireless router or wireless access point on the network.

NOTE: Wired connections are more reliable than wireless connections. If possible, you should connect devices to the network using an Ethernet cable.

• You may experience wireless interference if there are many nearby wireless access points. Change the channel on your router or wireless access point to test for and correct interference.

• Connecting a Bluetooth ® device to a stereo configured as a wireless access point or client may reduce wireless performance. Disconnect Bluetooth devices to test for and correct interference.

• If you configured static IP addresses, verify that every device has a unique IP address, that the first three sets of numbers in the IP addresses match, and that the subnet masks on every device are identical.

• If you have made configuration changes that might be causing networking issues, reset all network settings to the factory default values.

Apollo MS-RA670 Installation Instructions 15

Stereo Information

Specifications

Weight

Water rating

Operating temperature range

Storage temperature range

Input voltage

Current (max.)

Current (muted)

Current (off)

Fuse

NMEA 2000 LEN @ 9 Vdc

Bluetooth wireless range

ANT ® wireless range

Wireless frequencies/protocols

Compass-safe distance

750 g (26.5 oz.)

IEC 60529 IPX6 and IPX7 (front of stereo only, when properly installed) 1

From 0 to 50°C (from 32 to 122°F)

From -20 to 70°C (from -4 to 158°F)

From 10.8 to 16 Vdc

15 A

Less than 700 mA

Less than 200 mA

15 A mini blade-type

1 (50 mA)

Up to 10 m (30 ft.)

Up to 3 m (10 ft.)

Bluetooth 2.4 GHz @ from 13.29 dBm nominal

ANT 2.4 GHz @ from 6.92 dBm nominal

20 cm (7.87 in.)

On-board, Class D amplifier

Output music power per channel

Total output peak power

Output power per channel

4 x 70 W max. 2 ohm

280 W max.

4 x 43 W RMS at 14.4 Vdc input, 2 ohm, 10% THD 2

4 x 26 W RMS at 14.4 Vdc input, 4 ohm, 10% THD 2

5.5 V (peak to peak)

1 V RMS

Line output level (max.)

Aux input level (typical)

Tuner frequencies

Tuner

FM radio frequency range

FM frequency step

AM radio frequency range

AM frequency step

Europe and Australasia

87.5 to 108 MHz

50 kHz

522 to 1620 kHz

9 kHz

USA

87.5 to 107.9 MHz

200 kHz

530 to 1710 kHz

10 kHz

Japan

76 to 95 MHz

50 kHz

522 to 1620 kHz

9 kHz

1 The device withstands incidental exposure to water of up to 1 m for up to 30 min, and is protected against powerful jets of water. For more information, go to www.garmin.com/waterrating .

2 The stereo may limit the output power to prevent the amplifier from overheating, and to maintain the audio dynamics.

16 Apollo MS-RA670 Installation Instructions

Stereo Dimension Drawings

Side Dimensions

Top Dimensions

21 mm (0.83 in.)

102 mm (4.0 in.)

68 mm (2.68 in.)

49 mm (1.93 in.)

157 mm (6.18 in.)

130 mm (5.10 in.)

21 mm (0.83 in.)

10 mm (0.39 in.)

Software Updates

Go to support.garmin.com

to find software updates and information for your device.

Apollo MS-RA670 Installation Instructions 17

物質宣言

部件名称

有毒有害物 质 或元素

铅 汞 镉 六价 铬 多溴 联 苯

印刷 电 路板 组 件

屏幕 / 背光

金属零件

电缆 电缆组 件 连 接器

本表格依据 SJ/T11364 的 规 定 编 制。

: 代表此种部件的所有均 质 材料中所含的 该 种有害物 质 均低于

(GB/T26572) 规 定的限量

: 代表此种部件所用的均 质 材料中 , 至少有一 类 材料其所含的有害物 质 高于

(GB/T26572) 规 定的限量

* 該 產 品 說 明書應提供在環保使用期限和特殊標記的部分詳細講解 產 品的擔保使用條件。

多溴二苯 醚

產 品

© 2019–2021 Garmin Ltd. or its subsidiaries support.garmin.com