advertisement
harman/kardon
HKTS 200 SUB
(HKTS 20/HKTS 30/HKTS 60 SUBWOOFER)
SERVICE MANUAL
Released 2010
Discontinued XXXX harman/kardon, Inc.
8500 Balboa Blvd.
Northridge, CA. 91329 Rev1 3/2011
HKTS200SUB
CONTENTS
BASIC SPECIFICATIONS . . . . . . . . . . . . ……………………………………. . . . 1
DETAILED SPECIFICATIONS. . . . . . . . . . . . . .. . . . . . . . . ………………….. …2
PACKAGING. . . . . . . . . . . . . .. . . . . . . …….………………… . . . . .. . .. . .. . . . . 4
CONTROLS . . . . . . . . . . . . . .. . . . . . . ……………………… . ………………….. 5
CONNECTIONS …………………………………….………..……. . . .. . .. . . . .. . .. 6
OPERATION……. . . . . .. . . . . . . . .. .. . . . .. .. . . . . ……………………………….9
BASIC TROUBLESHOOTING GUIDE . . . . . . . . …………..……………………...9
TEST PROCEDURE. . . . . . . . . . . …………………………………………………10
AMPLIFIER EXPLODED VIEW. . . . …………… ………. ………... . . .. .. ... . … . 11
UNIT EXPLODED VIEW. . . . …………… ……………. .. ………... . . .. .. ... . … . 12
BLOCK DIAGRAM . . . . . . . . . . . . . .. . . . . . . ……………… . . . . .. . .. . .. . . . . 13
PCB DRAWINGS. .. . . . . . . . . . . . . . .. . . . . ……… . …………. . . . .. .. .. . .. . . . 14
ELECTRICAL PARTS LIST …………. .... . .. . . . …………………………... … . . 17
SEMICONDUCTOR PINOUTS . . . .. .. .. .. . . . .. . ……………..………..………. .19
SCHEMATIC DIAGRAMS . . . . . . . . .. .. .. .. . . . .. . ………………………..……. .37 harman/kardon
HKTS 200 SUB SPECIFICATIONS
Amplifier Power (RMS) 200 Watts
Frequency Response 45Hz – 200Hz
External Trigger Input Voltage 3 ~ 30 volts AC/DC
Dimensions (H x W x D) 13-29/32" x 10-1/2" x 10-1/2"
Occasional refinements may be made to existing products without notice but will always meet or exceed original specifications unless otherwise stated.
HKTS200SUB harman/kardon
Parameter
Amplifier Section
Type (Class AB, D, other)
Load Impedance (speaker)
Rated Output Power
THD @ Rated Power
THD @ 1 Watt
DC Offset
Damping Factor
Specification
D
4
200
<0.5
<0.2
<25
>10
HKTS200SUB Amplifier Specifications
Unit QA Test Limits
-
Ohm
W
%
% mV
DF
-
-
200
<1
<0.4
<35
-
Test Conditions, Notes, and Comments
No external heat sink required. Digital 192 kHz ternary mode PWM.
Minimum rated load impedance
50 Hz
AUX-0025 + AP DSP Audio Anlyzer + 20kHz LP
AUX-0025 + AP DSP Audio Anlyzer + 20kHz LP
Measured at amplifier board, damping factor dependant on H bridge Rdson + output filter impedance + SMPS, typically 0.1 + 0.2 + 0.05 Ohm.
Input Sensitivity
Input Reference Frequency
Input for 1 Watt Output
50
11.2
Gain (L, R and LFE inputs) 45
Signal to Noise
SNR-A-Weighted
SNR-un-weighted
Residual Noise Floor
70
60
<1
Hz mVrms ±1dB dB dBA dBr mVrms
67.5
-
-
L, R or LFE Input input to speaker output, Single input driven
RCA
(broad band noise from the ADC is present at the output but not audible) relative to 1W, AUX-0025 + AP DSP Audio Anlyzer + 20kHz LP + A-Weighting filter, PV measured ~350 uV relative to 1W, AUX-0025 + AP DSP Audio Anlyzer + 20kHz LP , PV measured 2mV
Band-pass Measurement at Line freq.+ harmonics, AUX-0025 + 22K + 20 brick wall filters,
Line level inputs may be terminated using 1K Ohm
Input Impedance
Line Input 10K
Filters & EQ
Amplifier frequency response
Amplifier frequency response
LP filter
HP Filter
LF Boost
AP Filter
Limiter
Limiter
Maximum THD Under Limiting
30-300
20-500
~160
~40
~50
80
Yes
5
Features
Volume Control Taper
Crossover Control
Phase Control
LF Boost Control
LED Indicator
Trigger Input
ATO Control
Input Configuration
Line In (R / L )
LFE In
Signal Sensing (ATO)
Auto-Turn-On (yes/no)
ATO Input test frequency
ATO Line input level
ATO Turn-on time
Time to Turn Off
LOG
No
0/180
Yes
Yes
Yes
Yes
Yes
Yes
Yes
50
1.5
<1
15
Ext. Trigger input
Activation Voltage
Activation current
Transients/Pops
ATO Transient
Turn-on Transient
Turn-off Transient
Protections
Output Short Circuit Protection
Output Over Current protection
Output DC Protection
Thermal Protection
Mains Fuse Rating (120v)
Mains Fuse Rating (230v)
Efficiency
Efficiency at rated power
Efficiency at 1/8 of rated power
Standby Input power
Idle input power
>3
<3
<0.5
<0.5
<0.5
75
60
0.8
8
Yes
12
Yes
Yes
6.3
5
Ohms
-
%
V mA
V-pp
V-pp
V-pp
-
A
-
A
A
-
-
Deg.
-
-
-
Hz
Hz
Hz
Hz
Hz
Hz
-
-
Hz mV s min
%
%
W
W
-
+/-1dB
+/-3dB
-
-
-
-
-
7
-
-
slo-blo slo-blo
Applies to L, R or LFE Inputs
Implemented using DSP
QA limits are relative to reference response
QA limits are relative to reference response
Fixed, 4th order
Fixed, 6th order
Selectable, 2nd order parametric, +3 dB
Crossover phase alignment.
Digital limiter integral to audio processor IC.
QA tests THD at up to 15 dB into limiter.
Functional
-
+/-10
Optional, 3-pin header on PCBA for future models.
2 position, 0 & 180
Functional 2 position, On & Off
Functional 2 state, Blue = On, Off = Off
Functional 3.5mm Mono Jack, Jack Sensing
Functional 2 position, On & Auto
Functional RCA Jacks, Red, White (Right and Left)
Functional RCA Jack, Purple
Functional
Functional
Functional QA Test is 1mV verify amplifier is off, 2.5 mV verify amplifier turns on.
Functional
Functional Time is measured by MCU, PV units measured 14 min.
Functional
Designed to trigger from 3.3 - 30 V sources, AC or DC, QA test uses 3 V DC for fucntion test. PV amplifiers measured 2.9 V AC, 1.6 V DC.
Functional ~30k input impedance
Functional Speaker Output, Amplifier wake from standby, PV sample < 0.1 V, not audible
Functional AC Line Connect, PV sample < 0.1 V, not audible
Functional AC Line Disconnect, PV sample < 0.1 V, not audible
-
-
<1
<10
Direct short between output terminal, recoverable @ 1 W, 50 Hz
Integral to power IC
Detects shorts to ground or VCC on outputs (H-Bridge Failure), LED blinks rapidly, SMPS is shut down to prevent, checks and attempts recovery every 20 seconds
NTC sensor adjacent power amplifier IC.
250V, Internal Fuse, SMPS PCBA mounted (pigtail, soldered in place).
250V, Internal Fuse, SMPS PCBA mounted (pigtail, soldered in place).
Nominal Line voltage, Mains input to speaker outputs.
2
HKTS200SUB
Parameter
Power supply
Type
Voltage Range
Operating frequency
Efficiency
Detachable AC power cord
Standby power draw
Specification Unit QA Test Limits
SMPS
220-240 or 100-
120
50-60
>80%
No
<0.5
-
Vac
Hz
-
-
W
Test Conditions, Notes, and Comments harman/kardon
-
190 & 264
-
-
-
-
Half bridge, with auxiliary fly back standby supply.
1/2 rated power continuous, and rated power for > 1 Minute, 25 degree ambient, rated resistive load measured on bench top.
IQC to test power supply at 264 V, 50 Hz input voltage, shall operate at +/- 10 % of the rated values
At rated power output
Fixed Euro Plug for 220-240 V units, and fixed US plug for 100-120 V units
ATO / Trigger Truth Table
Trigger Jack Sense
(1=jack, 0=no jack)
0
0
1
1
0
Trigger Input
State
(1 = high,
0=low)
1
0 x x x
Power
Mode
SW
(1=ON,
0=Auto) x x
1
0
0
Input Signal
Sense
(1=signal, 0=no signal) x x x
1
0
System State
On
Off
On
On
Off
3
HKTS200SUB
PACKAGING
harman/kardon
4
HKTS200SUB
HKTS200SUB Rear-Panel Connections
harman/kardon
1
2
3
4
5
6
7
8
9
PL0004-01001
1
Subwoofer Level Control: Use this control to adjust the HKTS200SUB’s
volume. Turn clockwise to increase the volume; turn counterclockwise
to decrease the volume.
2
Bass Boost Switch: Set this switch to ON to enhance the
HKTS200SUB’s low-frequency performance. Set this switch to OFF
for normal low-frequency performance.
3
Phase Switch: The Phase Switch determines whether the
HKTS200SUB’s piston-like action moves in and out in phase with the
satellite speakers. If the subwoofer were to play out of phase with the
satellite speakers, the sound waves produced by the subwoofer could
be canceled out, reducing bass performance and sonic impact.
This phenomenon depends in part on the relative placement of all the
speakers in the room. In most cases the Phase Switch should be left
in the NORMAL position. However, it does no harm to experiment,
and you can leave the Phase Switch
bass response and impact.
in the position that maximizes
4
Power On Mode Switch:
8
When set in the AUTO position and when
the Power Switch is set to ON , the HKTS200SUB will automatically
turn itself on when it receives an audio signal, and will enter the
standby mode once no audio signal has been received for about
15 minutes. When this switch is set in the ON position,
the HKTS200SUB will remain on whether or not it is receiving an
audio signal.
An LED on the HKTS200SUB’s top panel indicates whether the
subwoofer is in the on or standby state:
• When the LED is illuminated white, the HKTS200SUB is turned on.
• When the LED is not illuminated, the HKTS200SUB is in standby mode.
When the Master Power Switch is set to OFF , the LED will not be
illuminated, no matter what setting the
5
Power On Mode Switch is in.
External Trigger Input: Use the mini-plug of the supplied combination
LFE and trigger cable to connect the External Trigger Input to the
trigger output of another compatible component. Whenever a trigger
signal between 3 and 30V (AC or DC) is detected, the HKTS200SUB’s
amplifier will turn on. The HKTS200SUB’s amplifier will turn off after
5
the trigger signal ceases. (This will occur even when the Power On Mode
Switch is in the AUTO position.)
6
Line-Level LFE In Connector: Use the LFE (purple) connector of the
supplied combination LFE and trigger cable to connect the Line-Level
LFE In to the dedicated subwoofer output of a receiver or preamp/
processor. This input bypasses the HKTS200SUB’s internal crossover
circuitry, so it should only be used with a subwoofer output that has
been low-pass filtered. If your receiver or preamp/processor does not
have a dedicated subwoofer output that is low-pass filtered you should
use the HKTS200SUB’s Line-Level L/R In Connectors instead.
7
Line-Level L/R In Connectors: Use these connectors if your receiver or
preamp/processor does not have digital surround sound decoding or a
subwoofer output that is low-pass filtered.
• If your receiver or preamp/processor has a separate subwoofer
output, use the LFE (purple) connector of the supplied combination
LFE and trigger cable to connect it to either one of the HKTS200SUB’s
Line-Level L/R In Connectors .
• If your receiver or preamp/processor does not have a separate
subwoofer output, use two Y-adapters (not supplied). Connect an
adapter’s single end to the unit’s preamp output for that channel.
Connect one of the adapter’s dual ends to the main amp input for that
channel, and connect the adapter’s other dual end to one of the
HKTS200SUB’s Line-Level L/R In Connectors . Repeat with the other
Y-adapter, preamp channel, main amp input and HKTS200SUB
Line-Level L/R In Connector .
8
Power Switch: Set this switch in the ON position to turn the
HKTS200SUB on. The subwoofer will then either be on or in standby
mode, depending on the setting of the Power On Mode Switch .
9
Power Cord (Non-Detachable): After you have made and verified all
subwoofer and speaker connections described in this manual, plug this
cord into an active, unswitched electrical outlet for proper operation of
the HKTS200SUB. DO NOT plug this cord into the accessory outlets
found in some audio components.
HKTS200SUB
Left Front Center Right Front harman/kardon
Front Left
Speaker Cable
(White Bands)
– +
Center
Speaker Cable
(Green Bands)
– +
Front Right
Speaker Cable
(Red Bands)
– +
FRONT
+ –
RIGHT
–
LEFT
– – + +
Receiver
Surround Left
Speaker Cable
(Blue Bands)
– +
CENTER
+ –
SUB
LFE OUT
LFE/Trigger Cable
(Purple Ends)
Surround Right
Speaker Cable
(Gray Bands)
– +
Subwoofer
Left
Surround
Right
Surround
Connecting the Subwoofer to a Receiver or
Preamp/Processor With a Dedicated Subwoofer Output
Use this installation method for receivers and preamp/processors that have a dedicated subwoofer output with low-pass filtering (also called bass management). If the dedicated subwoofer output does not have low-pass filtering, follow the instructions in Connecting the Subwoofer to a Receiver or Preamp/Processor With Line Outputs, on page 9.
Connect each satellite speaker and the center speaker to the
corresponding speaker terminals on your receiver or amplifier.
Use the LFE (purple) connector of the supplied combination LFE and trigger cable to connect the HKTS200SUB’s Line-Level LFE In Jack
6 to the dedicated subwoofer output (or LFE output) of your receiver or preamp/processor.
In your receiver or preamp/processor’s setup menu, configure it for
Subwoofer ON , and set the front left, front right, center, and surround
speakers to Small . After you have made and verified all connections,
plug the HKTS200SUB’s AC Power Cord into an active AC outlet.
6
HKTS200SUB
Left Front Center Right Front harman/kardon
Front Left
Speaker Cable
(White Bands)
– +
Center
Speaker Cable
(Green Bands)
– +
Front Right
Speaker Cable
(Red Bands)
– +
FRONT
+ –
RIGHT
–
LEFT
– – + +
Receiver
Surround Left
Speaker Cable
(Blue Bands)
– +
CENTER
+ –
LINE-LEVEL
OUTPUTS
L R
Surround Right
Speaker Cable
(Gray Bands)
Subwoofer
RCA Cable
(Not Supplied)
(Red and White Ends)
– +
Left
Surround
Right
Surround
Connecting the Subwoofer to a Receiver or Preamp/Processor With Line Outputs
Use this installation method for receivers and preamp/processors that do not have a dedicated subwoofer output, but do have preamp-level
(volume-controlled) line outputs. If the receiver or preamp/processor has a dedicated subwoofer output with low-pass filtering, see Connecting the Subwoofer to a Receiver or Preamp/Processor With a Dedicated
Subwoofer Output , on page 8.
inputs, connect the single ends of Y-adapters (not supplied) to
the receiver’s or processor’s left and right line outputs. Connect one
of the Y-adapter’s double ends to the HKTS200SUB’s Line-Level L/R
In Connectors , and connect the other double end to your
amplifier’s front left and right inputs.
If you’re connecting to a receiver with left and right line outputs that are not connected to amplifier inputs, connect the LFE (purple) connector of the supplied combination LFE and trigger cable to one of those outputs and to either of the HKTS200SUB’s Line-Level L/R In Connectors . Use a second RCA cable (not supplied) to connect the other receiver or preamp line output to the other of the HKTS200SUB’s Line-
Level L/R In Connectors .
If you’re connecting to a receiver or preamp/processor with left and right line outputs that are connected to amplifier front left and right
Connect each satellite speaker and the center speaker to the
corresponding speaker terminals on your receiver or amplifier.
In your receiver or preamp/processor’s setup menu, configure it for
Subwoofer ON , and set the front left, front right, center, and surround
speakers to Small .
After you have made and verified all connections, plug the
HKTS200SUB’s AC Power Cord into an active AC outlet.
7
HKTS200SUB
FRONT
+ –
RIGHT
–
LEFT
– –
Receiver
CENTER
+ –
+ +
LFE SUB
OUTPUT
TRIGGER
OUT harman/kardon
Subwoofer
Trigger Cable
(Black Ends)
PL0004-01001
Connecting to a Trigger Voltage Source
If your preamp/processor or another audio/video component has a trigger voltage connection that supplies between 3 and 30V (AC or DC), connect it to the HKTS200SUB’s External Trigger Input Connector . If the component’s trigger voltage connection has a 3.5mm mini jack you can use the supplied combination LFE/trigger cable to make the connection.
NOTE: Please do not connect the subwoofer ON/OFF trigger cable to the
Remote Control Output (IR Out) of your home cinema system or surround receiver. This could lead to malfunction.
8
HKTS200SUB
Operation
Turning the Subwoofer On and Off
Set the HKTS200SUB’s Power Switch to the ON position.
• If the Power On Mode Switch is set to AUTO , the HKTS200SUB will automatically turn itself on when it receives an audio signal, and it will go into standby mode when it has received no audio signal for 15 minutes. The HKTS200 SUB’s LED will illuminate white when the subwoofer is on, and will not be illuminated when the subwoofer is in standby.
• If the Power On Mode Switch is set to ON , the HKTS200SUB will remain on at all times. The HKTS200 SUB’s LED will illuminate white.
4
• If the External Trigger Input Connector is connected to a trigger voltage source, the HKTS200SUB will turn on whenever a trigger voltage is present, and will turn off after the trigger voltage ceases, regardless of the position of the Power On Mode Switch .
If you will be away from home for an extended period of time, or if you will not be using the subwoofer for an extended period, switch the Power Switch to the OFF Position.
Subwoofer Adjustments: Volume
Use the Subwoofer Level Control to set the HKTS200SUB’s volume. Turn the knob clockwise to increase the subwoofer’s volume; turn the knob counterclockwise to decrease the subwoofer’s volume.
Subwoofer Adjustments: Phase
The Phase Switch determines whether the HKTS200SUB’s piston-like action moves in and out in phase with the satellite speakers. If the subwoofer were to play out of phase with the satellite speakers, the sound waves produced by the subwoofer could be canceled out, reducing bass performance and sonic impact.
This phenomenon depends in part on the relative placement of all the speakers in the room.
Although in most cases the Phase Switch should be left in the
NORMAL position, there is no absolute correct setting for the
Phase Switch . When the HKTS200SUB is properly in phase with the satellite speakers, the sound will be clearer and have maximum impact. This will make percussive sounds like drums, piano and plucked strings sound more lifelike. The best way to set the Phase Switch is to listen to music that you are familiar with and set the switch in the position that gives drums and other percussive sounds maximum impact.
Subwoofer Adjustments: Bass Boost
When set to the ON position, the Bass Boost Switch enhances low-frequency performance, resulting in bass with more impact, which you may prefer while watching movies or listening to music.
There is no harm in experimenting with this control – setting the switch to the OFF position will return normal low-frequency performance. harman/kardon
Troubleshooting
If there is no sound from any of the speakers:
• Check that the receiver/amplifier is on and a source is playing.
• Make sure that all wires and connections between the receiver/amplifier
and the speakers are connected properly.
• Make sure none of the speaker wires is frayed, cut or punctured.
• Review the proper operation of your receiver/amplifier.
If there is no sound coming from one speaker:
• Check that the balance control on your receiver/amplifier is not set all the
way to one channel.
• Check your receiver/amplifier’s speaker setup procedure to make sure that
the speaker in question has been enabled and its volume level has not been
turned all the way down.
• Make sure that all wires and connections between the receiver/amplifier
and the speaker are connected properly.
• Make sure the speaker wires are not frayed, cut or punctured.
If there is no sound coming from the center speaker:
• Check your receiver/amplifier’s speaker setup procedure to make sure that
the center speaker has been enabled and its volume level has not been
turned all the way down.
• Make sure that all wires and connections between the receiver/amplifier
and the center speaker are connected properly.
• Make sure the speaker wires are not frayed, cut or punctured.
• If your receiver is operating in Dolby ®
center speaker is not set to Phantom.
Pro Logic ® mode, make sure that the
If there is no sound coming from the surround speakers:
• Check your receiver/amplifier’s speaker setup procedure to make sure that
the surround speakers have been enabled and their volume levels have not
been turned all the way down.
• Make sure that all wires and connections between the receiver/amplifier
and the surround speakers are connected properly.
• Make sure the speaker wires are not frayed, cut or punctured.
• Review proper operation of your receiver/processor and its surround-
sound features.
• Make sure the movie or TV show you’re watching has been recorded in a
surround-sound mode. If it is not, check to see if your receiver/amplifier has
a different surround-sound mode that you can use.
• Review the operation of your DVD player and the DVD jacket to make sure the
DVD features the desired Dolby Digital or DTS
menu and the disc’s menu.
® surround-sound mode,
and that you have properly selected that mode using both the DVD player’s
If there is no sound coming from the subwoofer :
• Check that the subwoofer’s
AC outlet.
Power Cord is plugged into a working
• Check that the subwoofer’s Power Switch
1
is in the ON position.
• Check that the Subwoofer Level Control is not turned all the way down
(fully counterclockwise).
• Check the audio connection between your receiver/processor and
the subwoofer.
• Check your receiver/amplifier’s speaker setup procedure to make sure that
the subwoofer has been enabled and its volume level has not been turned
all the way down.
If the system plays at low volumes but shuts off as volume is increased:
• Make sure that all wires and connections between the receiver/amplifier
and the speakers are connected properly.
• Make sure none of the speaker wires is frayed, cut or punctured.
• If you’re using more than one pair of main speakers, check to be sure that
you’re not operating the system below the receiver/amplifier’s minimum
impedance requirements.
9
HKTS200SUB
Test Set Up and Procedure
harman/kardon
Equipment needed:
•
Function/signal generator/sweep generator
•
Integrated
•
Multimeter
Initial Control Settings:
•
Power Switch OFF; Bass Mode OFF
•
Level MIN (Full CCW)
•
Phase, Auto/On switches do not matter
General Unit Function (UUT = Unit Under Test)
1) From the signal generator, connect one line level (RCA) cable to the Subwoofer Line Level Input jacks L/R on the UUT. Use a Y-cable from a mono source if necessary to connect to both inputs. Do not connect to the single, purple SUB input.
2) Turn on generator; adjust to 100mV, 50 Hz .
3) Plug in UUT; turn the power switch ON. Turn LEVEL control full clockwise (MAX)
4) LED should be white (on top of UUT); immediate and vigorous bass response should be heard and felt from woofer on bottom of subwoofer.
Sweep Function
1) Follow steps 1-4 above, using a sweep generator as a signal source.
2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or any other noises. If any unusual noises are heard, remove woofers and test.
Driver Function
1) Remove woofer from cabinet; detach + and - wire clips.
2) Check DC resistance of woofer; it should be 3.4 ohms ±10%
3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0
V.
4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
10
HKTS200SUB harman/kardon
BPVA00032-0001-ABS-AMP Rear Cover
GALA00113-0001-AL 5052-Heat sink
DSS100017-0001-Nylon66-SPACER SUPPORT-E*2PCS
HNT009540-1230-NUT-E*7PCS
HSB053083-1120-Screw-E*2PCS
APEA00690-4001-PCBA
DSS100043-0001-Nylon66-SPACER SUPPORT-E*4PCS
GCUA00023-0001- BRASS-RCA Shield Cap
TPS220200-0408-SMPS
IVHA12002-0001-SEAL PE PAD-OBAE*2PCS
IVHA12002-0002-SEAL PE PAD-OBAE*2PCS
XBT090001-M000-BUTYL TAP
IVEA00168-0001-SEAL EVA -OBAE*2PCS
IVEA00168-0002-SEAL EVA -OBAE*2PCS
DKNA01009-0001-Small knob
HSP043083-3100-Screw-E*2PCS
HSP140054-3100-Screw-E*1PC
GALA00112-0002-AL-Rear Plate
HSP053083-3200-Screw-E*4PCS
MSW108001-0015 -Power Switch
IVAA02071-0001 Wire Tie
11
HKTS200SUB harman/kardon
12
HKTS200SUB harman/kardon
HKTS200SUB Subwoofer Block Diagram
LED Two 2-pos Slide
Switch’s
Trigger Input, plug and level detection
IO
ADC
Analog
Input Buffer (w/ potentiometer for volume ctrl) to ADC, for standby
MCU
(Renesas R8C/1B Series, 8 kB flash)
(8 MHz)
ADC
NTC Temperature
Sensor
Power Stage Fault
Detection Circuit
ADC (AK5358A, 24 bit, 32 kHz, 102 dB) clk
I2C
Audio Processor / PWM
Modulator
(ST309A, 36 bit)
Power Stage
(ST516B, 1x2 00 W)
Woofer
(4 Ohm)
I2S clk
OSC
(8.192 MHz)
Standby Ctrl
Power Supply
200 W SMPS, 200-264 / 90 –132 V switchable ac input
+48 V for 200 W into 4 Ohms
13
CAM Products 2000(TM):
HKTS200SUB harman/kardon
14
CAM Products 2000(TM):
HKTS200SUB harman/kardon
15
CAM Products 2000(TM):
HKTS200SUB harman/kardon
16
HKTS200SUB
HKTS200SUB Electrical Parts list
Part number Description
MAIN PCB
Resistors
QCF015030-0000
QCF011030-1801
QCF011030-1002
QCF011030-1004
QCF015030-5100
QCF011030-4991
QCF011030-4992
QCF011030-1003
QCF011030-2202
QCF011030-3301
QCF011030-1000
QCF011030-1001
QCF011030-4703
QCF045010-2200
QCF011030-2204
QCF045010-6290
QCF011030-1333
QCF081020-1009
QCF011030-1009
MVRA02202-1020
Capacitors
GP CHIP RES. 0 OHM 1/10W 5% 0603
GP CHIP RES. 1.8K OHM 1/10W 1% 0603
GP CHIP RES. 10K OHM 1/10W 1% 0603
GP CHIP RES. 1M OHM 1/10W 1% 0603
GP CHIP RES. 51 OHM 1/10W 5% 0603
GP CHIP RES. 4.99K OHM 1/10W 1% 0603
GP CHIP RES. 49.9K OHM 1/10W 1% 0603
GP CHIP RES. 100K OHM 1/10W 1% 0603
GP CHIP RES. 22K OHM 1/10W 1% 0603
GP CHIP RES. 3.3K OHM 1/10W 1% 0603
GP CHIP RES. 100 OHM 1/10W 1% 0603
GP CHIP RES. 1K OHM 1/10W 1% 0603
CHIP RES. 470K OHM 1/10W 1% 0603
GP CHIP RES. 22 OHM 1/4W 5% 1206
GP CHIP RES. 2.2M OHM 1/10W 1% 0603
GP CHIP RES. 6.2 OHM 1/4W 5% 1206
GP CHIP RES. 133K OHM 1/10W 1% 0603
GP CHIP RES. 10 OHM 1/8W 1% 0805
GP CHIP RES. 10 OHM 1/10W 1% 0603
CNTL ROTRY 1K OHM LEVEL
Qty Reference Designator harman/kardon
2 R77 R78
1 R3
R35 R42 R44 R45 R53 R54 R56 R79
6 R4 R30 R40 R47 R68 R70
6 R7 R15 R16 R18 R31 R32
3 R9 R14 R17
2 R12 R22
5 R21 R57 R61 R80 R81
4 R25 R23 R24 R82
1 R26
2 R33 R60
1 R37
R69 R72 R74
3 R49 R58 R65
2 R51 R75
2 R52 R67
1 R59
2 R62 R73
1 R71
1 VR1
PXL456470-1040
PXL410370-1220
PXL410370-2200
PXL456470-1010
PYL456420-1060
PXL456470-2240
PXL456470-4740
PXL456470-2210
PYL439520-2260
PXL4564A0-1040
PXL456470-1030
PXL4564A0-3310
PXL4564A0-1020
PXL456440-1050
PXL456470-1020
PYL4564A0-4740
PZL4564A4-1051
PZL4564A0-2250
PME099540-2200
PME099540-1010
PME999540-2200
PLE599580-1020
Semiconductors
RCI700405-0002
RCI005343-0001
RCI000720-0001
RCI000309-0001
RCI000809-0008
RCI052114-0001
GP CHIP CAP 0.1uF 50V 10%
GP CHIP CAP 1.2nF 50V 5%
GP CHIP CAP 22pF 50V 5%
GP CHIP CAP 100pF 50V 10%
CHIP CAP 10uF 6.3V 10% 0805 X7R
CHIP CAP 220nF 50V 10%
GP CHIP CAP 470NF 50V 10%
GP CHIP CAP 220pF 50V 10%
CHIP CAP 22uF 6.3V 20%
CHIP CAP 0.1uF 100V 10%
GP CHIP CAP 0.01uF 50V 10%
CHIP CAP 330pF 100V 10%
CHIP CAP 1nF 100V 10%
GP CHIP CAP 1uF 16V 10%
GP CHIP CAP 0.001 uF 50V 10%
GP CHIP CAP 470NF 100V 10%
GP CHIP CAP 1uF 100V 10% 1206 X7R
GP CHIP CAP 2.2uF 100V 10%
GP COND ELECT 22uF 16V 20% 5x11mm
GP COND ELECT 100uF 16V 20% 5X11
COND ELECT 22uF 16V 20% 105' 4x7
COND ELECT 1000uF 63V 20% 105' 16x25
IC 5P NC7SZ04M5X MA05B TinyLogic UHS Inverter
IC ADC 10 PIN CS5343 CIRRUS Multi-Bit Audio A/D Converter
IC 8P TL072CDR SOIC ST DUAL OP AMP
GP IC 64P STA309A Multi-channel digital audio processor
GP IC 3P AZ809ANSTR-E1 MICRO RESET CIRCUIT
IC 20P R5F211B4DD48S PLSP0020JB-A RENESAS PROCESSOR
17
35
C1 C2 C3 C7 C15 C17 C19 C25 C26 C34
C36 C38 C39 C40 C45 C46 C47 C49 C54
C55 C56 C57 C58 C76 C81 C84 C86 C87
C88 C91 C93 C95 C23 C101 C102
4 C4 C5 C33 C48
6 C8 C9 C16 C28 C29 C30
9 C11 C21 C22 C24 C37 C43 C99 C100 C6
4 C13 C44 C12 C18
1 C32
3 C41 C71 C97
1 C42
3 C50 C85 C92
5 C52 C65 C67 C79 C83
2 C59 C90
4 C63 C66 C69 C72
3 C64 C68 C78
4 C73 C27 C31 C98
1 C75
2 C61 C74
3 C62 C70 C80
3 C53 C60 C77
4 C10 C14 C20 C82
2 C89 C94
1 C96
1 C51
1 IC1
1 IC2
1 IC3
1 IC4
1 IC5
1 IC6
HKTS200SUB
Part number
RCI111733-1102
RCI111750-0001
RCI000516-0001
RCP000856-0001
RCP003906-0002
RCN000846-0001
RCN003904-0008
RCD100540-0010
RCZ005002-0020
Description
3P AP1117E33LA SOT223 Low Drop Pos Adjustable/Fixed-Mode Regulator
3P LM1117MPX-5.0 SOT-223 Low-Dropout Linear Regulator
IC 36P STA516B SO36 60 V 6 A quad power half bridge
GP TRANSISTOR PNP BC856B SOT-23
CHIP TRANSISTOR 3P PNP MMBT3906 PNP SOT23
GP TRANSISTOR NPN BC846B SOT23
TRANSISTOR NPN MMBT3904 SOT-23 FAIRCHILD
GP DIODE CHIP BAT54S (3PIN)
CHIP ZENER 2.7V 5% 0.5W LL34
Qty Reference Designator
1 IC7
1 IC8
1 IC9
2 T3 T8
1 T7
4 T4 T5 T9 T10
2 T2 T6
2 D1 D6
2 ZD1 ZD2
TPS220200-0407 SMPS power supply (120v)
TPS220200-0408 SMPS power supply (230v)
Miscellaneous
RNT000030-1002
SCB008051-6010
JCQA13010-1251
CCP254260-0104
CCN396020-0102
CJRA03401-0010
CJMA35002-3010
VWA310054-0002
VWA010034-0001
VWA200056-0001
SINA03701-1000
DHU109001-0001
MSWA04001-0010
GCUA00023-0001
SFB005002-6000
VPAA14013-0010
MSW108001-0015
GALA00112-0001
NTC 10k Ohm 1%,0603, MURATA
CHIP BEAD 600 OHM 25% AT 100MHZ SMD 0805
SMD CHIP CRYSTAL 12.288MHz 30ppm
HEAD PIN 4P P2.54xH11.5MM
GP CONNECTOR 2 PIN LEOCO 3951
RCA JACK RCA313 WHITE/RED/PURPLE
PHONE JACK 3.5mm HSJ-035-09-K
C/W 2P 100mm 2468#18 RED-BLACK
C/W 4P 90mm 1007#26 BLACK/WHITE/RED
C/W 2P 210mm 2468#26 RED/BLACK
INDUCTOR 10UH 20% D0.9x8.5TS
PCB HOUSING L11.5xW8.5xH11.2xT0.8
SLIDE SWITCH SK-22F03 6 PIN BASS/PHASE/AUTO
HKTS30-RCA SHIELD CAP
BEAD FERIT 60 OHM 100MHz 3.5x6mm
AC power cord (120v)
AC power switch
Aluminum amp plate (silkscreened)
BPVA00032-0001-ABS-AMP Plastic amp cover
GALA00113-0001-AL Heatsink
DKNA01009-0001
IVAA02071-0001
Level knob
Strain Relief Plug
1
1
1
1
1
1
1
1
1 R36
7 B1 B3 B4 B5 B6 B8 B9
1 X1
1 CN2
1 SP1
1 J1
1 J2
1 CN1
1 CN4
1 LD1
2 L1 L2
1 M1
3 S1 S2 S3
1 J6
1 B7
1 harman/kardon
18
HKTS200SUB harman/kardon
IC6
IC8
IC3
IC4
19
T2,T6
HKTS200SUB harman/kardon
T7
IC9
T4,T5,T9,T10
IC1
IC5
20
harman/kardon
IC2
T3,T8
D1,D6
21
HKTS200SUB
REJ09B0252-0110
harman/kardon
16
R8C/1A Group, R8C/1B Group
Hardware Manual
RENESAS 16-BIT SINGLE-CHIP MICROCOMPUTER
M16C FAMILY / R8C/Tiny SERIES
All information contained in these materials, including products and product specifications, represents information on the product at the time of publication and is subject to change by
Renesas Technology Corp. without notice. Please review the latest information published by Renesas Technology Corp. through various means, including the Renesas Technology
Corp. website (http://www.renesas.com).
Rev.1.10
22
HKTS200SUB
R8C/1A Group, R8C/1B Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER harman/kardon
REJ09B0252-0110
Rev.1.10
Mar 17, 2006
1.
Overview
These MCUs are fabricated using the high-performance silicon gate CMOS process, embedding the R8C/
Tiny Series CPU core, and is packaged in a 20-pin molded-plastic LSSOP, SDIP or a 28-pin plastic molded-
HWQFN. It implements sophisticated instructions for a high level of instruction efficiency. With 1 Mbyte of address space, they are capable of executing instructions at high speed.
Furthermore, the R8C/1B Group has on-chip data flash ROM (1 KB × 2 blocks).
The difference between the R8C/1A Group and R8C/1B Group is only the presence or absence of data flash ROM. Their peripheral functions are the same.
1.1
Applications
Electric household appliances, office equipment, housing equipment (sensors, security systems), general industrial equipment, audio equipment, etc.
R8C/1A Group, R8C/1B Group 1. Overview
1.5
Pin Assignments
Figure 1.4 shows Pin Assignments for PLSP0020JB-A Package (Top View), Figure 1.5 shows Pin
Assignments for PRDP0020BA-A Package (Top View) and Figure 1.6 shows Pin Assignments for
PWQN0028KA-B Package (Top View).
PIN assignments (top view)
P3_5/SSCK/SCL/CMP1_2
P3_7/CNTR0/SSO/TXD1
RESET
XOUT/P4_7 (1)
VSS/AVSS
XIN/P4_6
VCC/AVCC
MODE
P4_5/INT0/RXD1
P1_7/CNTR00/INT10
4
5
6
7
1
2
3
8
9
10
13
12
11
16
15
14
20
19
18
17
P3_4/SCS/SDA/CMP1_1
P3_3/TCIN/INT3/SSI00/CMP1_0
P1_0/KI0/AN8/CMP0_0
P1_1/KI1/AN9/CMP0_1
P4_2/VREF
P1_2/KI2/AN10/CMP0_2
P1_3/KI3/AN11/TZOUT
P1_4/TXD0
P1_5/RXD0/CNTR01/INT11
P1_6/CLK0/SSI01
NOTE:
1. P4_7 is an input-only port.
Package: PLSP0020JB-A (20P2F-A)
Figure 1.4
Pin Assignments for PLSP0020JB-A Package (Top View)
23
Rev.1.10
Mar 17, 2006 Page 7 of 312
REJ09B0252-0110
HKTS200SUB
R8C/1A Group, R8C/1B Group harman/kardon
PIN assignments (top view)
P3_5/SSCK/SCL/CMP1_2
P3_7/CNTR0/SSO/TXD1
RESET
XOUT/P4_7 (1)
VSS/AVSS
XIN/P4_6
VCC/AVCC
MODE
P4_5/INT0/RXD1
P1_7/CNTR00/INT10
7
8
5
6
9
10
3
4
1
2
16
15
14
18
17
20
19
13
12
11
P3_4/SCS/SDA/CMP1_1
P3_3/TCIN/INT3/SSI00/CMP1_0
P1_0/KI0/AN8/CMP0_0
P1_1/KI1/AN9/CMP0_1
P4_2/VREF
P1_2/KI2/AN10/CMP0_2
P1_3/KI3/AN11/TZOUT
P1_4/TXD0
P1_5/RXD0/CNTR01/INT11
P1_6/CLK0/SSI01
NOTE:
1. P4_7 is an input-only port.
Package: PRDP0020BA-A (20P4B)
Figure 1.5
Pin Assignments for PRDP0020BA-A Package (Top View)
1. Overview
Rev.1.10
Mar 17, 2006 Page 8 of 312
REJ09B0252-0110
24
HKTS200SUB
R8C/1A Group, R8C/1B Group harman/kardon
1. Overview
1.6
Pin Functions
Table 1.5 lists Pin Functions, Table 1.6 lists Pin Name Information by Pin Number of PLSP0020JB-A,
PRDP0020BA-A Packages and Table 1.7 lists Pin Name Information by Pin Number of PWQN0028KA-
B Package.
Table 1.5
Pin Functions
Type
Analog Power
Supply Input
Reset Input
MODE
AVCC, AVSS
RESET
MODE
Main Clock Input XIN
Main Clock Output XOUT
Symbol
Power Supply Input VCC, VSS
INT Interrupt INT0, INT1, INT3
Key Input Interrupt KI0 to KI3
Timer X CNTR0
CNTR0
Timer Z
Timer C
TZOUT
TCIN
CMP0_0 to CMP0_2,
CMP1_0 to CMP1_2
I/O Type
I
Description
Apply 2.7 V to 5.5 V to the VCC pin.
Apply 0 V to the VSS pin.
I
I
O
I
I
O
I
O
Power supply for the A/D converter
Connect a capacitor between AVCC and AVSS.
Input “L” on this pin resets the MCU.
Connect this pin to VCC via a resistor.
These pins are provided for main clock generation circuit I/O. Connect a ceramic resonator or a crystal oscillator between the XIN and XOUT pins.
To use an external clock, input it to the XIN pin and leave the XOUT pin open.
I
I INT interrupt input pins
Key input interrupt input pins
I/O Timer X I/O pin
O Timer X output pin
Timer Z output pin
Timer C input pin
Timer C output pins
Serial Interface
Clock synchronous serial I/O with chip select (SSU)
CLK0
RXD0, RXD1
TXD0, TXD1
SSI00, SSI01
SCS
SSCK
I/O Transfer clock I/O pin
I Serial data input pins
O Serial data output pins
I/O Data I/O pin.
I/O Chip-select signal I/O pin
I/O Clock I/O pin
Reference Voltage
Input
SSO
I 2 C bus Interface SCL
SDA
VREF
I/O
I/O
I/O
I
Data I/O pin
Clock I/O pin
Data I/O pin
Reference voltage input pin to A/D converter
A/D Converter
I/O Port
Input Port
I: Input O: Output
AN8 to AN11
P1_0 to P1_7,
P3_3 to P3_5, P3_7,
P4_5
P4_2, P4_6, P4_7 I
I
I/O: Input and output
Analog input pins to A/D converter
I/O CMOS I/O ports. Each port has an I/O select direction register, allowing each pin in the port to be directed for input or output individually.
Any port set to input can be set to use a pull-up resistor or not by a program.
P1_0 to P1_3 also function as LED drive ports.
Input-only ports
Rev.1.10
Mar 17,
25
HKTS200SUB
R8C/1A Group, R8C/1B Group harman/kardon
1. Overview
7
8
9
4
5
6
10
1
2
3
16
17
18
11
12
13
14
15
19
Table 1.6
Pin
Number
20
Pin Name Information by Pin Number of PLSP0020JB-A, PRDP0020BA-A Packages
Control
Pin
Port
P3_5
P3_7
Interrupt
I/O Pin Functions for Peripheral Modules
Timer
Serial
Interface
Clock
Synchronous
Serial I/O with
Chip Select
I 2 C bus
Interface
CMP1_2
CNTR0 TXD1
SSCK
SSO
SCL
A/D
Converter
RESET
XOUT
VSS/AVSS
XIN
VCC/AVCC
MODE
P4_7
P4_6
VREF
P4_5
P1_7
P1_6
P1_5
P1_4
P1_3
P1_2
P4_2
P1_1
P1_0
P3_3
P3_4
INT0
KI3
RXD1
INT10
CNTR00
CLK0
INT11 CNTR01 RXD0
TXD0
TZOUT
KI2
CMP0_2
KI1
KI0
INT3
CMP0_1
CMP0_0
TCIN/
CMP1_0
CMP1_1
SSI01
SSI00
SCS
SDA
AN11
AN10
AN9
AN8
Rev.1.10
Mar 1
26
HKTS200SUB
R8C/1A Group, R8C/1B Group harman/kardon
1. Overview
18
19
20
21
22
23
12
13
14
15
16
17
4
5
6
7
1
2
3
8
9
10
11
24
25
26
27
28
Table 1.7
Pin
Number
Pin Name Information by Pin Number of PWQN0028KA-B Package
Control
Pin
Port
Interrupt
I/O Pin Functions for Peripheral Modules
Timer
Serial
Interface
Clock
Synchronous
Serial I/O with
Chip Select
I 2 C bus
Interface
A/D
Converter
NC
XOUT
VSS/AVSS
NC
NC
XIN
NC
VCC/AVCC
MODE
P4_7
P4_6
P4_5 INT0
P1_7
INT10
P1_6
P1_5 INT11
P1_4
CNTR00
CNTR01
RXD1
CLK0
RXD0
TXD0
SSI01
NC
P1_3
P1_2
KI3
KI2
TZOUT
CMP0_2
AN11
AN10
NC
NC
VREF
NC
P4_2
P1_1
P1_0
P3_3
P3_4
P3_5
P3_7
KI1
KI0
INT3
CMP0_1
CMP0_0
TCIN/CMP1_0
CMP1_1
CMP1_2
CNTR0
TXD1
SSI00
SCS
SSCK
SSO
SDA
SCL
AN9
AN8
RESET
Rev.1.10
Mar 1
27
HKTS200SUB harman/kardon
CS5343/4
98 dB, 96 kHz, Multi-Bit Audio A/D Converter
Features
!
Advanced Multi-Bit ∆Σ Architecture
!
24-bit Conversion
!
Supports Audio Sample Rates Up to 108 kHz
!
98 dB Dynamic Range at 5 V
!
-90 dB THD+N
!
Low-Latency Digital Filter
!
High-Pass Filter to Remove DC Offsets
!
Single +3.3 V or +5 V Power Supply
!
Power Consumption Less Than 50 mW
!
Master or Slave Operation
!
Slave Mode Speed Auto-Detect
!
Master Mode Default Settings
!
256x or 384x MCLK/LRCK Ratio
!
CS5343 Supports I²S Audio Format
!
CS5344 Supports Left-Justified Audio Format
General Description
The CS5343/4 is a complete analog-to-digital converter for digital audio systems. It performs sampling, analogto-digital conversion, and anti-alias filtering, generating
24-bit values for both left and right inputs in serial form at sample rates up to 108 kHz per channel.
The CS5343/4 uses a 3rd-order, multi-bit Delta-Sigma modulator followed by a digital filter, which removes the need for an external anti-alias filter.
The CS5343/4 also features a high-impedance sampling network which eliminates costly external components such as op-amps.
The CS5343/4 is available in a 10-pin TSSOP package for both Commercial (-10° to +70° C) and Automotive grades (-40° to +85° C). The CDB5343 Customer Demonstration Board is also available for device evaluation and implementation suggestions. Please refer to the
“Ordering Information” on page 21 for complete details.
The CS5343/4 is ideal for audio systems requiring wide dynamic range, negligible distortion and low noise, such as set-top boxes, DVD-karaoke players, DVD recorders, A/V receivers, and automotive applications.
VA
3.3 V to 5 V
Single-Ended
Analog Input
AINL
High-Z
Sampling
Network
FILT+
VQ
Internal
Reference
Voltages
Low-Latency
Digital Filters
Auto-detect
MCLK Divider
Slave Mode
Auto-detect
Master
Clock
SCLK
LRCK
Single-Ended
Analog Input
AINR
High-Z
Sampling
Network
Low-Latency
Digital Filters
SDOUT
High-Pass
Filter
Advance Product Information
http://www.cirrus.com
This document contains information for a new product.
Cirrus Logic reserves the right to modify this product without notice.
AUGUST '06
DS687A4
28
HKTS200SUB harman/kardon
1. PIN DESCRIPTIONS
SDOUT
SCLK
LRCK
MCLK
FILT+
3
4
1
2
5
10
9
8
7
6
VA
GND
AINR
VQ
AINL
CS5343/4
MCLK
FILT+
AINL
AINR
VQ
GND
VA
Pin Name Pin #
SDOUT
SCLK
LRCK
Pin Description
1
Serial Audio Data Output ( Output ) - Output for two’s complement serial audio data. Also selects Master or Slave Mode.
2 Serial Clock ( Input/Output ) - Serial clock for the serial audio interface.
3
Left Right Clock ( Input/Output ) - Determines which channel, Left or Right, is currently active on the serial audio data line.
4 Master Clock ( Input ) - Clock source for the delta-sigma modulator and digital filters.
5 Positive Voltage Reference ( Output ) - Positive reference voltage for the internal sampling circuits.
6
8
Analog Input cation table.
( Input ) - The full-scale analog input level is specified in the Analog Characteristics specifi-
7 Quiescent Voltage (Output) - Filter connection for the internal quiescent reference voltage.
9 Ground ( Input ) - Ground reference. Must be connected to analog ground.
10 Power ( Input ) - Positive power supply for the digital and analog sections.
4
29
DS687A4
HKTS200SUB
harman/kardon
October 1996
Revised June 2000
NC7SZ04
TinyLogic
UHS Inverter
General Description
The NC7SZ04 is a single inverter from Fairchild’s Ultra
High Speed Series of TinyLogic
. The device is fabricated with advanced CMOS technology to achieve ultra high speed with high output drive while maintaining low static power dissipation over a very broad V
CC
operating range.
The device is specified to operate over the 1.8V to 5.5V
V
CC
range. The inputs and output are high impedance when V
CC
is 0V. Inputs tolerate voltages up to 6V independent of V
CC
operating voltage.
Features
■ Space saving SOT23 or SC70 5-lead package
■ Ultra High Speed; t
PD
2.4 ns typ into 50 pF at 5V V
CC
■ High Output Drive;
±
24 mA at 3V V
CC
■ Broad V
CC
Operating Range; 1.8V to 5.5V
■ Matches the performance of LCX when operated at
3.3V V
CC
■ Power down high impedance inputs/output
■ Overvoltage tolerant inputs facilitate 5V to 3V translation
■ Patented noise/EMI reduction circuitry implemented
Ordering Code:
Order
Number
NC7SZ04M5
NC7SZ04M5X
NC7SZ04P5
NC7SZ04P5X
Number
MA05B
MA05B
MAA05A
MAA05A
Logic Symbol
IEEE/IEC
Top Mark
7Z04
7Z04
Z04
Z04
Package Description Supplied As
5-Lead SOT23, JEDEC MO-178, 1.6mm
5-Lead SOT23, JEDEC MO-178, 1.6mm
250 Units on Tape and Reel
3k Units on Tape and Reel
5-Lead SC70, EIAJ SC-88a, 1.25mm Wide 250 Units on Tape and Reel
5-Lead SC70, EIAJ SC-88a, 1.25mm Wide 3k Units on Tape and Reel
Connection Diagram
Pin Descriptions
Pin Names
A
Y
NC
Description
Input
Output
No Connect
(Top View)
Function Table
Y
=
A
H
=
HIGH Logic Level
L
=
LOW Logic Level
Input
A
L
H
Output
Y
H
L
TinyLogic
is a trademark of Fairchild Semiconductor Corporation.
30
HKTS200SUB harman/kardon
STA309A
Multi-channel digital audio processor with DDX®
Features
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
8 channels of 24-bit DDX
®
>100 dB SNR and dynamic range
Selectable 32 kHz - 192 kHz input sample rates
6 channels of DSD/SACD input
Digital gain/attenuation +58 dB to -100 dB in
0.5 dB steps
Soft volume update
Individual channel and master gain/attenuation plus channel trim (-10 dB to +10 dB)
Up to 10 independent 32-bit user programmable biquads (EQ) per channel
Bass/treble tone control
Pre and post EQ full 8-channel input mix on all
8 channels
Dual independent limiters/compressors
Dynamic range compression or anti-clipping modes
AutoModes:
– 5-band graphic EQ
– 32 preset EQ curves (rock, jazz, pop, etc.)
– Automatic volume controlled loudness
– 5.1 to 2-channel downmix
– Simultaneous 5.1- and 2-channel downmix outputs
– 3 preset volume curves
– 2 preset anti-clipping modes
– Preset movie nighttime listening mode
– Preset TV channel/commercial AGC mode
– 5.1, 2.1 bass management configurations
– AM frequency automatic output PWM frequency shifting
– 8 preset crossover filters
Individual channel and master soft/hard mute
Automatic zero-detect and invalid input mute
Automatic invalid input detect mute
TQFP64
!
!
!
!
!
!
!
!
!
!
Advanced PopFree operation
Advanced AM interference frequency switching and noise suppression modes
I
2
S output channel mapping function
Independent channel volume and DSP bypass
Channel mapping of any input to any processing/DDX
®
channel
DC blocking selectable high-pass filter
Selectable per-channel DDX
®
damped ternary or binary PWM output
Max power correction for lower full-power THD
Variable per channel DDX
®
output delay control
192 kHz internal processing sample rate, 24-bit to 36-bit precision
Description
The STA309A is a single chip solution for digital audio processing and control in multi-channel applications. It provides output capabilities for
DDX
®
(direct digital amplification). In conjunction with a DDX
®
power device, it provides highquality, high-efficiency, all digital amplification.
The device is extremely versatile, allowing for input of most digital formats including 6.1/7.1channel and 192 kHz, 24-bit DVD-audio,
DSD/SACD. In 5.1 application the additional 2 channels can be used for audio line-out or headphone drive. In speaker mode, with 8 channel outputs in parallel, the STA309A can deliver more than 1 W.
Table 1.
STA309A
Device summary
Order code
TQFP64
Package
September 2007 Rev 1 1/67
67
31
HKTS200SUB
STA309A
Figure 1.
Block diagram
LRCKI
BICKI
SDI12
SDI34
SDI56
SDI78
SERIAL
DATA
IN
SA SCL SDA MVO
I 2 C
SYSTEM
CONTROL
OVERSAMPLING
DDX
PLLB
CHANNEL
MAPPING
VARIABLE
OVER-
SAMPLING
PLL
SYSTEM TIMING
TREBLE,
BASS, EQ
(BIQUADS)
POWER
DOWN
VOLUME
LIMITING
VARIABLE
DOWN-
SAMPLING
XTI CKOUT PWDN EAPD
SERIAL
DATA
OUT
Figure 2.
Channel signal flow
6 Inputs
From DSD
DSD
Conversion
Interp_Rate
8 Inputs
From I2S
1x,2x,4x
Interp
DSDE
Mapping/
Mix #1
Biquads
B/T
Mix #2
Volume
Limiter
OUT1A/B
OUT2A/B
OUT3A/B
OUT4A/B
OUT5A/B
OUT6A/B
OUT7A/B
OUT8A/B
LRCKO
BICKO
SDO12
SDO34
SDO56
SDO78
2x
Interp
Distortion
Compensation
DDX
Output
NS C_Con PWM
From
Mix#1
Engine
Or
Previous
Channel
Biquad#10
Output
(CxBLP)
PreScale
Hard Set to
-18dB when
AutoMode EQ
(AMEQ)
High-Pass
Filter
User Progammable
Biquad #1 when
High-Pass Bypassed
(HPB)
Biquad
#2
Biquad
#3
Biquad
#4
Biquad
#5
Hard Set Coeffecients when AutoMode EQ
(AMEQ)
Biquad
#6
Biquad
#7
Biquad
#8
Bass Treble
Hard Set
Coeffecients when
AutoMode
Bass Management
Crossover
(AMBMXE)
Hard Set
Coeffecients when
DeEmphasis
Enabled
(DEMP)
User Programmable
Biquads #9 and #10
When Tone Bypassed
(CxTCB)
To
Mix#2
Engine harman/kardon
Block diagram
9/67
32
HKTS200SUB
Pin connections harman/kardon
STA309A
Figure 3.
Pin connection (top view)
MVO
GND
VDD
GND
NC
SDI_78
SDI_56
SDI_34
SDI_12
LRCKI
BICKI
VDD
GND
NC
RESET
PLLB
14
15
16
10
11
12
13
8
9
6
7
3
4
5
1
2
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
38
37
36
35
34
33
48
47
46
45
44
43
42
41
40
39
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
OUT2_A
OUT2_B
NC
GND
VDD
OUT3_A
OUT3_B
OUT4_A
OUT4_B
OUT5_A
OUT5_B
NC
GND
VDD
OUT6_A
OUT6_B
STA308APINCON
10/67
11
15
16
Table 2.
Pin
1
6
7
8
9
10
Pin description
Type Name
5-V tolerant TTL input buffer MVO/DSD_CLK
5-V tolerant TTL input buffer SDI_78/DSD_6
5-V tolerant TTL input buffer SDI_56/DSD_5
5-V tolerant TTL input buffer SDI_34/DSD_4
5-V tolerant TTL input buffer SDI_12/DSD_3
5-V tolerant TTL input buffer LRCKI/DSD_2
5-V tolerant TTL input buffer BICKI/DSD_1
5-V tolerant TTL schmitt trigger input buffer
CMOS input buffer with pull-down
RESET
PLL_BYPASS
Description
Master volume override/
DSD input clock
Input serial data channels 7 & 8/
DSD input channel 6
Input serial data channels 5 & 6/
DSD input channel 5
Input serial data channels 3 & 4/
DSD input channel 4
Input serial data channels 1 & 2/
DSD input channel 3
Input left/right clock/
DSD input channel 2
Input serial clock/
DSD input channel 1
Global reset
Bypass phase locked loop
33
HKTS200SUB
STA309A
43
47
41
42
39
40
34
38
32
33
30
31
19
20
21
23
24
25
29
Table 2.
Pin
17
18
Pin description (continued)
Type Name
CMOS input buffer with pull-down
SA
Bidirectional buffer: 5-V tolerant TTL schmitt trigger input; 3.3-V capable 2mA slew-rate controlled output.
SDA
5-V tolerant TTL schmitt trigger input buffer
5-V tolerant TTL schmitt trigger input buffer
Analog pad
Analog ground
SCL
XTI
FILTER_PLL
GNDA
3.3V analog supply voltage VDDA
3.3-V capable TTL tristate
4mA output buffer
3.3-V capable TTL 16mA output buffer
CKOUT
OUT8B
3.3-V capable TTL 16mA output buffer
3.3-V capable TTL 16mA output buffer
OUT8A
OUT7B
3.3-V capable TTL 16mA output buffer
3.3-V capable TTL 16mA output buffer
3.3-V capable TTL 16mA output buffer
3.3-V capable TTL 16mA output buffer
3.3-V capable TTL 16mA output buffer
3.3-V capable TTL 16mA output buffer
3.3-V capable TTL 16mA output buffer
3.3-V capable TTL 16mA output buffer
3.3-V capable TTL 16mA output buffer
3.3-V capable TTL 16mA output buffer
OUT7A
OUT6B
OUT6A
OUT5B
OUT5A
OUT4B
OUT4A
OUT3B
OUT3A
OUT2B harman/kardon
Pin connections
Description
Select address (I
2
C)
Serial data (I
2
C)
Serial clock (I
2
C)
Crystal oscillator input (clock input)
PLL filter
PLL ground
PLL supply
Clock output
PWM channel 8 output B
PWM channel 8 output A
PWM channel 7 output B
PWM channel 7 output A
PWM channel 6 output B
PWM channel 6 output A
PWM channel 5 output B
PWM channel 5 output A
PWM channel 4 output B
PWM channel 4 output A
PWM channel 3 output B
PWM channel 3 output A
PWM channel 2 output B
11/67
34
HKTS200SUB
Pin connections
Table 2.
Pin
Pin description (continued)
Type Name
48
49
50
51
55
56
57
58
3.3-V capable TTL 16mA output buffer
3.3-V capable TTL 16mA output buffer
3.3-V capable TTL 16mA output buffer
3.3-V capable TTL 4mA output buffer
3.3-V capable TTL 2mA output buffer
3.3-V capable TTL 2mA output buffer
3.3-V capable TTL 2mA output buffer
3.3-V capable TTL 2mA output buffer
OUT2A
OUT1B
OUT1A
EAPD
BICKO
LRCKO
SDO_12
SDO_34
62
63
64
3.3-V capable TTL 2mA output buffer
3.3-V capable TTL 2mA output buffer
5-V tolerant TTL schmitt trigger input buffer
SDO_56
SDO_78
PWDN
3,12,28,35,
44,52,59
2,4,13,27,
36,45,53,60
3.3-V digital supply voltage VDD
Digital ground GND
5, 14, 22,
26,37,46,54,
61
NC harman/kardon
STA309A
Description
PWM channel 2 output A
PWM channel 1 output B
PWM channel 1 output A
Ext. amp power-down
Output serial clock
Output left/right clock
Output serial data channels 1&2
Output serial data channels 3&4
Output serial data channels 5&6
Output serial data channels 7&8
Device power-down
3.3-V supply
Ground
Not connected
12/67
35
HKTS200SUB harman/kardon
36
C
B
D
A
!
RT1
L
!
!
CN1
C65
F1
1
1
N
2
!
CN2
3 4
TR2
HV
C21
C22
HV
!
!
CX1
!
R42
LF1
!
CX2
!
LF2
GND
R44
C12
C16
6
11
C15
6
!
TR1
5
C13
R34
D10
R35
T7
!
5
4 9
R36
D11
!
CY2
4
C14
DW1
GND
R20
9
8
10 C7
D3
DW3
D21
C5
R18
D19
GND
GND
C4
R6
R11
R2
4
R4
R3
2
13
C3
3
IC1
IC1
14
12
11
GND
R12
C2
16
15
D18
R17
8
GND
6
5
7 9 10
C1
R8
1
D20
2
1
R37
T4
GND
GND
C8
R1
R54
C34
!
TR3
C26
5
R45 R47
R43
D25
D24
R23
T8
R22 C23
7
6
2
IC3
4
3
8
1
5
C24
R21
4
2
1
D1
10
9
GND
8
D22
7
D2
GND
L3
L2
GND
2
D12
D23
R38
R39
T6
D9
T5
Q2
R25
R24
R57
R56
C9
!
D8
D15
D5
GND
D4
R28
R9
R5
C19
3
HKTS200SUB
37
D6
D7
DW6
IC2
GND
R51
R10
CN3
3
4
1
2
+7V
GND
-7V
STB
R53
4
3
HV
GND
Vref
C27
10
!
CY3
!
CY1
GND
R16
GND
GND
C18
Q1
DD1
5
L1
GND
HYS3B210-CS harman/kardon
6
V+
CN4
1
2
V+
GND
NOTE the SMPS power supply should be replaced in its entirety and the schematic is supplied only for reference
120v part# TPS220200-0407
230v part# TPS220200-0408
5 6
A.2
D
C
B
A
A
B
C
D
1 2 3 4 5 6 7 8
HKTS200SUB harman/kardon
R
L
LFE
J1
5
2
3
4
C21
100pF
C11
100pF
+
C20
22uF
+
C10
+
22uF
R13
10k
R10
10k
10k
R6
6
5
2
3
C4 1.2nF
R5 10k
IC3
7
1
R14
4.99k
+7V
VR1
3
B1K
M1
PCB_HOLDER
R9
2.7k
C22
100pF
R12
49.9k
R17
4.99k
C37
100pF
C35
22uF
(DNP)
J2
5
4
2
1
3
22K
R23
BAT54S
D1
R82
22K
TRIGGER/AUDIO IN
B5
C50
22uF
10k R3
JACK SENSE
R30
1M
+3.3V
C102
100nF
C47
100nF
Vdd
R35
10k
1
POWER ON
2
RESET
FILTER
MODE
PHASE
9
10
7
8
5
6
3
4
R5F211A4
IC6
P3_5
P3_7
RESET
XOUT
VSS
XIN
VCC
MODE
P4_5
P1_7
R24
22K
P3_4
P3_3
P1_0
P1_1
VREF
P1_2
P1_3
P1_4
P1_5
P1_6
R21
ZD2
2.7V
+3.3V
D6
BAT54S
20
19
C33 1.2nF
C41
470nF
100k
PDN
14
13
12
11
18
17
16
15
SIGNAL SENSE
Temp.Detect
crossover
TRIGGER
AUTO/ON
OSC_CTR
LED
CN2
DCP
DCP
100nF C58 s1
Filter
C57 C55 s2
AUTO/ON
100nF 100nF s3
+3.3V
PHASE
R44
10k
R45
10k
+7V
CN4
R60
100
B9
R61
100k
T7
2N3906
R54
10k
C82
22uF16V
+7V
+7V
R65
22
C87
100nF
C89
100uF
R71
10
T6
2N3904
R57
100k
C75
1nF
3
LM1117-3.3
IC7
3
C85
22uF
+3.3V
IC8
LM1117-5.0
+5V
10
R73 C92
22uF -7V
-7V
C96
100uF16V
+3.3V
+5V
-7V
C32
220nF
R22
49.9k
R20
10k
Vdd
+3.3V
R27
10k
C101
100nF
+3.3V
CN3
R33
100
R28
10k
2.7V
ZD1
SPK+
R78
0
R55
1M
(DNP)
SPK-
R77
0
R40
1M
R51
2.2M
R68
1M
R75
2.2M
R2
10k
C12
10uF
C18
+5V
10uF
C99
100pF
B3
C100
100pF
C27
1uF
C25
100nF
C31
1uF
C34
100nF
6
IC2
AINL FILT+
7
VQ MCLK
8
AINR LRCK
9
GND SCLK
10
VA SDOUT
CS5343
4
3
2
1
R79
10k
C23
5
100nF
R80
100k
(DNP)
R1
1.8k
T1
(DNP)
2N3904
+3.3V
B1
2
NC
VCC
5
3
GND
4
NC7SZ04
R4
1M
100nF
C3
R7
51
R3
1.8k
X1
8.192MHz
C8
22pF
C9
22pF
C98
1uF
R15 51
R16 51
R18 51
MCLK
R81
100k
C16
22pF
SDTO
C28 C29
22pF 22pF
LRCK
SCLK
C30
22pF
PDN_ctr
+3.3V
LD1
LED
R25
22k
+3.3V
R29 10k T2
C45
100nF
R38
470k
VCC
R48
470k
T3
BC856B
R47
1M
R43
470k
C59
10nF
R50
470k
T5
C71
470nF
BC846B
R63
470k
T8
BC856B
VCC
R70
1M
R72
470k
T10
R74
470k
R69
470k
C90
10nF
2N3904
VCC
VCC
R39
470k
R41
470k
T4
BC846B
R64
470k
R66
470k
T9
BC846B
DCP
SDA
(DNP)
ZD3
2.7V
C73
1uF
R59
133k
+3.3V
SCL
IN5A
IN5B
EAPD
B8
C81
100nF
C54
100nF
C56
100nF
IN5A
IN5B
R53
R56
10k
10k
C76
100nF
C84
100nF
VCCSIGN
VCCSIGN
VSS
VSS
IN2B
IN2A
IN1B
IN1A
TH_WAR
FAULT
TRI_STATE
PWDN
CONFIG
VL
VDD
VDD
GND_REG
GND_CLR
33
32
31
30
29
28
27
26
36
35
34
25
24
23
22
21
20
19
3
+3.3V
R36
NTC
R31
51
R32
51
+3.3V
C17
100nF C19
100nF
2
C38
100nF
MVO
GND
VDD3
GND
NC
SDI78
SDI56
SDI34
SDI12
LRCKI
BICKI
VDD3
GND
NC
RESET
PLLB
11
12
13
14
9
10
7
8
15
16
3
4
1
2
5
6
308_SDA
308_SCL
+3.3V
C5
1.2nF
C1
100nF
R26
3k3
C43
100pF
C48
1.2nF
C2
100nF
IC4
STA309A
C49
100nF
C44
10uF
B4
B6
EAPD
OUT2A
OUT2B
NC
GND
VDD3
OUT3A
OUT3B
OUT4A
OUT4B
OUT5A
OUT5B
NC
GND
VDD3
OUT6A
OUT6B
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
100nF
10uF
C13
C15
+3.3V
IN5A
IN5B
+3.3V
C40
100nF
+3.3V
C46
100nF
EAPD
+3.3V
R37
3.3k
GND_SUB
OUT2B
OUT2B
VCC2B
GND2B
GND2A
VCC2A
OUT2A
OUT2A
OUT1B
OUT1B
VCC1B
GND1B
GND1A
VCC1A
OUT1A
OUT1A
NC
VCC
8
9
10
11
6
7
4
5
1
2
3
16
17
18
12
13
14
15
C77
2.2uF
VCC
C51
1000uF
47uF C6
OUT2
OUT1
C74
0.47uF
C52
100nF
VCC
*
VCC
*
*
B7
*
D2
D3
D4
D5
2.2uF
C53
R49
22
L1
C66
330pF
+48V
22uH
C69
330pF
R58
22
22uH
L2
CN1
C80
1uF
C63
C62
1uF
100V
330pF
C65
100nF
SPK+
C67
100nF
R52
6.2
C64
1nF
C72
330pF
C70
1uF
100V
C79
100nF
C83
100nF
SPK-
R67
6.2
C78
1nF
SPK+
C68
1nF
SP1
SPK-
IC9
STA516B
R76
1M
(DNP)
C97
470nF
BC846B
1 2 3 4
38
5 6
Title
HKTS200SUB
DrawnBy:
Meican.wu
ApprovedBy:
File:
Ruben Millyard
E:\Work\HKTS\SCH2.SchDoc
Size:
Date:
A3
2009-7-23
7
Revision:
Sheet 1
1.
of 1
1
8
A
B
C
D
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- 200 watts of RMS power for deep, impactful bass
- 8" woofer for rich, immersive sound
- Stereo line level and dedicated subwoofer (LFE) inputs for compatibility with a wide range of audio systems
- Built-in crossover and phase control for fine-tuning the sound
- Compact and stylish design that complements any home theater system
Related manuals
Frequently Answers and Questions
What is the RMS power output of the HKTS 200 SUB?
What size woofer does the HKTS 200 SUB have?
What types of inputs does the HKTS 200 SUB have?
Does the HKTS 200 SUB have a built-in crossover?
Does the HKTS 200 SUB have a phase control?
advertisement