User manual

Wireless 2CH Relay

www.hdlautomation.com

HDL-MPR02-RF.18

Document updates:

Version Date

V1.0

2015.09.05

Finish new document

Description

User Manual

HDL-MPR02-RF.18

Wireless Relay –User Manual

User Manual

HDL-MPR02-RF.18

INDEX

1. Overview ........................................................................................................................................

1

1.1 General Information ...........................................................................................................

1

1.1.1 Description ...............................................................................................................

1

1.1.2 Dimensions ..............................................................................................................

1

1.2 Functionalities Description ...............................................................................................

1

1.3 Device Description .............................................................................................................

2

2. Safety Instructions .......................................................................................................................

2

3. Technical Data ..............................................................................................................................

3

4. Important Notes ............................................................................................................................

4

5. Software Configuration ................................................................................................................

4

5.1 Basic Information ...............................................................................................................

4

5.1.1 Wireless Setting via Mesh Gateway ...................................................................

4

5.1.2 Device configuration ..............................................................................................

6

5.1.3 Remark ..................................................................................

错误！未定义书签。

5.2 Channel ...............................................................................................................................

7

5.2.1 Channel Information ...............................................................................................

7

5.2.2 Mains frequency .....................................................................................................

7

5.2.3 Status restore when power on .............................................................................

7

5.3 Configuration ......................................................................................................................

8

5.3.1 Setting For Keys .....................................................................................................

8

5.3.2 Remark .....................................................................................................................

8

5.3.3 Switch type ..............................................................................................................

9

5.3.4 Unqualifiedde ........................................................................................................

11

5.3.5 Delay time ..............................................................................................................

11

5.3.6 Dimming .................................................................................................................

12

5.3.7 Target ......................................................................................................................

12

5.3.8 Low limit .................................................................................................................

13

6. Note ..............................................................................................................................................

14

Wireless Relay –User Manual

User Manual

HDL-MPR02-RF.18

1. Overview

1.1 General Information

1.1.1 Description

HDL-MPR02-RF.18 wireless 2 channels relay, has 4CH dry contact, can control target by switch. This module should be configured by wireless gateway.

1.1.2 Dimensions

44mm

17mm

36mm

36mm

 Wall box

1.2 Functionalities Description

 2CH relay output

 Support switch on delay, protection delay, switch off delay, switch off delay

 The 4CH dry contact supports: mechanical switch and electronic switch, can control the target, has dimming function

 The dry contact supports: mechanical switch, single on, single off, single on/off, combination on/off, muti-function, parallel switch

 Each switch type can set switch mode, dimmable two-way, dimmable increase, dimmable reduce.

 Control type: scene, sequence, universal switch, single channel lighting control, broadcast scene, broadcast channel, curtain switch, GPRS control switch, panel

Wireless Relay – User Manual 1

User Manual

HDL-MPR02-RF.18

control, security module, z-audio control

 Support IEEE.802.15.4

 Support online upgrading

 Support easy programming

1.3 Device Description

Antenna

L

L

N

N

Programming button

Dry contact Programming button: if it is working properly, the green light will flicker, press the button three times continuously, the green light will flicker quickly, enter the setup mode

(the gateway should enter the setup mode at the same time,so that can set the wireless parameters for it)

2. Safety Instructions

 When power on, cannot touch the power, load, load, dry contact terminal, avoid electric shock.

 Never let the liquids get into the module, it will damage this device.

 Ensure good ventilation.

 Output channel – The following list is the recommended for output channel. To protect the relay, please connect a 16A breaker for each channel.

 Recommended load type and power (work in AC220V)

Motors 1HP (1HP=746W)

Incandescent lamp load 3500W

Inductive transformer 450W

Wireless Relay – User Manual 2

Electronic transformer

Halogen lamp

Mercury vapor lamp

*Uncompensated lamp:

*Parallel compensated lamp

Fluorescent lamp T5/T8

*Uncompensated lamp

*Parallel compensated lamp

*DUO lamp

Dulux lamp

*Uncompensated lamp

*Parallel compensated lamp

875W

500W

500W

375W

375W

500W

3500W

700W

700W

3. Technical Data

Electrical Parameter:

Input voltage

Output current

Power consumption

Wireless transmit power

Wireless receive sensitivity

Indoor communication distance

RSSI receive signal receiving

Wireless central frequency:

WPAN (China)

SRD (Europe)

ISM (North America)

Default band

Default PSK

Environmental Condition:

Working temperature

Wireless Relay – User Manual

AC85-265V, 50/60Hz

8A

Max.0.45W

<=30m

>-80dbm

780 to 786MHz

864 to 870MHz

904 to 928MHz

780MHz

HDL-SecurityKey0

-5%~45%

User Manual

HDL-MPR02-RF.18

3

User Manual

HDL-MPR02-RF.18

Working relative humidity

Storage temperature

Storage relative humidity

Approved

CE

RoHS

Product Information ：

Dimensions

Weight

Housing material

Installation

Protection degree

Fire and null wire

Load cable

Stripping length

Up to 90%

-20%~+60%

Up to 93%

44×36×17 (mm)

39.7g

PC

Wall box

IP20

1.5mm

2 (the module provides 15cm wire)

1.5mm

2 (the module provides 15cm wire)

5~7mm

4. Important Notes

 This module should work with wireless gateway

 Connection – Check the connection, avoid short circuit

 When power on, cannot touch the power, load and dry contact terminal, avoid the electric shock

 The subnet ID of wireless relay should be same as wireless gateway

5. Software Configuration

5.1 Basic Information

5.1.1 Wireless Setting via Mesh Gateway

Before user can configure the wireless relay normally, need to set the wireless parameters for it via mesh gateway, and the mesh gateway needs to work in mesh mode.

Wireless Relay – User Manual 4

User Manual

HDL-MPR02-RF.18

1- Set the free frequency and unique PSK PWD for the gateway

2- Press the ‘PROG’ button 3 times continuously, the red LED will flash quickly that means the gateway enters the wireless setup mode.

3- Press the programming button of wireless 2CH relay 3 times continuously, the green

LED will flash quickly, enter the setup mode.

4- Click the ‘Search’ button, the wireless relay will be shown as below

5- Select the mode, you will be able to change its ID and remark it (the subnet ID must be same as the gateway)

Wireless Relay – User Manual 5

User Manual

HDL-MPR02-RF.18

6- Click ‘Modify Setting of Selection’, then all its wireless parameters will follow the gateway’s (Band, Frequency and PSK).

7- Click ‘all Node Exit Setup’, then the wireless devices will exit the wireless setup mode

8- Go to the HDL Buspro setup tool’s main interface to search and add the wireless relay, then can start to configure it.

5.1.2 Device Information

Displays the device’s information.

Wireless Relay – User Manual 6

User Manual

HDL-MPR02-RF.18

5.2 Channel

5.2.1 Channel Information

Switching on delay: When receives the on command, will not switch on immediately but after the delay time.

Protection delay: If a protection delay of 1 minute is set, and the relay channel is turned off, it cannot be turned on again until 1 minute later. This is useful for loads which are not suitable to be rapidly turned on and off.

Off delay: when receives the off command, will not switch off immediately but after the delay time.

Remark: Do the remark for easy management.

5.2.2

Mains frequency

It supports 50Hz/60Hz

5.2.3 Status restore when power on

Click ‘Enable’, when power on the wireless relay, it will turn back to the status before power off.

Wireless Relay – User Manual 7

User Manual

HDL-MPR02-RF.18

5.3 Configuration

This relay module has 4 dry contact inputs, they have the same functions as wired dry contact module.

5.3.1 Setting For Keys

Key Enable : enable/disable the channels

Panel Lock Key Enable : If be selected, can use panel to lock/unlock this channel.

5.3.2 Remark

Do the remark for easy management.

Wireless Relay – User Manual 8

5.3.3 Switch type

Two different Switch types - Momentary and Toggle

You can find two different types of switch from the market.

Momentary Switch - When pressed, it is on, when released, it is off.

User Manual

HDL-MPR02-RF.18

If “ Electrical switch ” is selected for this kind of switch, a momentary effect can be produced.

Toggle Switch – It is bi-stable switch, you can set it on or off.

Generally select “Mechanic switch” mode for this kind of switch.

Switch type:

Mechanic Switch

Send out a command (generally the on command, e.g., light on.) when Switch is

Wireless Relay – User Manual 9

User Manual

HDL-MPR02-RF.18

connected, send out another (generally the off command) when the Switch is disconnected.

Single on

Assign the Switch can turn on one object only (one channel, or one scene, or one sequence, etc.)

Single off

Assign the Switch can turn off one object only (one channel, or one scene, or one sequence, etc.)

Single on/off

Assign the Switch can turn on/off one object only (one channel, or one scene, or one sequence, etc.)

Combination on

Assign the Switch can turn on multiple objects (channels, scenes, sequence, etc.)

Combination off

Assign the Switch can turn off multiple objects (channels, scenes, sequence, etc.)

Combination on/off

Assign the Switch can turn on/off multiple objects (channels, scenes, sequence, etc.)

Multi-function

Long press – combination off (or dim, if dimming is enabled in the Dry Contact module.

Dim the first object only, though.)

Short press – single on/off

Double click – Combination on

This mode can be used in, maybe, meeting, by double-click all the lighting can be on, by long-press, all lighting can be off, this can avoid mishandling and so it is more secure.

Parallel Switch

This key mode is originally designed for retrofit project where the end-users want to implement HDL wireless system, but they want to reserve the existing toggle buttons, the toggle buttons are to control one public area lighting (e.g., stair lighting) from multiple places.

Wireless Relay – User Manual 10

Wiring

Connect the two toggle buttons to two different dry contact channels

Setting

Select “Parallel switch” for both dry contact channels

5.3.4 Unqualifiedde

User Manual

HDL-MPR02-RF.18

Each channel can set the mode

Switch mode: on/off control

Dimmable increase: long press to dim up

Dimmable reduced: long press to dim down

Dimmable two-way: long press to dim up, long press again can dim down

5.3.5 Delay time

Only the “Mechanic switch” switch type has the delay time.

Wireless Relay – User Manual 11

User Manual

HDL-MPR02-RF.18

5.3.6 Dimming

Key no. : channel no./ switch no.

Dimming value:

Togglewhen turn on light, the brightness will go to 100%

Memorysave the brightness, when turn on light, the brightness will go to last brightness before turn off

5.3.7 Target

Can set each channel’s controlled targets, the target’s range is 1~20.

Wireless Relay – User Manual 12

User Manual

HDL-MPR02-RF.18

5.3.8 Low limit

Set the dimming lower limit.

The Lower limit is useful if you would like to skip the low level segment and dim from a certain level, say 50%. You want to skip it because maybe lower than 50% is impractical for you or maybe the load quality is not so good and trembles when at low level segment.

Wireless Relay – User Manual 13

User Manual

HDL-MPR02-RF.18

6. Note

……………………………………………………………………………………………………….

………………………………………………………………………………………………………

………………………………………………………………………………………………………

………………………………………………………………………………………………………

………………………………………………………………………………………………………

………………………………………………………………………………………………………

………………………………………………………………………………………………………

………………………………………………………………………………………………………

………………………………………………………………………………………………………

………………………………………………………………………………………………………

………………………………………………………………………………………………………

………………………………………………………………………………………………………

………………………………………………………………………………………………………

………………………………………………………………………………………………………

………………………………………………………………………………………………………

………………………………………………………………………………………………………

………………………………………………………………………………………………………

………………………………………………………………………………………………………

………………………………………………………………………………………………………

………………………………………………………………………………………………………

………………………………………………………………………………………………………

………………………………………………………………………………………………………

………………………………………………………………………………………………………

………………………………………………………………………………………………………

………………………………………………………………………………………………………

………………………………………………………………………………………………………

………………………………………………………………………………………………………

Wireless Relay – User Manual 14