advertisement
User Manual
GF-1130-4412 MH
GF-2230-4412 MH
ANITA B s.r.o.
Průmyslová 2453/7
680 01 Boskovice
Czech republic tel: +420 516 454 774
+420 516 453 496 fax: +420 516 452 751 e-mail:
[email protected]
MP04800EN,MP04900EN_200204
VERSION DATE APPROVED BY
MP04800EN,MP04900EN_200204 4. 2. 2020 Ing. Kamil Krátký www.garudan.cz
All rights reserved. Property of Anita B s.r.o. and protected by copyright.
The use of this content without written consent of Anita B s.r.o. is prohibited.
Copyright © Anita B s.r.o. (2020)
© ANITA
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 2
© ANITA
Content
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 3
© ANITA
www.garudan.cz
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 4
© ANITA
A BASIC INFORMATION
A1.
PRODUCT DESCRIPTION AND INTENDED USE
The machines are designated for use in the apparel, home textiles, accessories and footwear production. It is suitable for making a car seat covers, sofas, leather bags, tents, etc. Triple synchronous feed and special feeder provide smooth operation and even stitch even for heavy materials. Characteristic features of this machine are low level of noise and vibrations and large-capacity hook.
A2.
TECHNICAL SPECIFICATIONS
Model
Number of needles
Needle gauge
Use
Stitch type
Max. stitch length
Hand lever foot lift
Knee lever foot lift
Needle system
Needle size
Hook type
Lubrication
Motor
GF-1130-4412 MH
1
-
GF-2230-4412 MH
2
6.4 mm / 7.9 mm /
9.5 mm / 12.7 mm
Medium/Heavy materials
2-thread lockstitch max. 9 mm
9 mm
19 mm
135x17 for fabrics, 135x16 for leather
Nm. 110 -180 *
Vertical with ∅ 26 mm bobbin
Automatic with oil pump
Integrated servomotor 1x230V
60 kg Machine head weight 58 kg
Table weight
Working space
27 kg www.garudan.cz
Machine table dimensions 515 x 180 mm
Power
Ground plan dimensions (including frame)
Bedplate height
Machine height including thread stand
Noise level under standard conditions max. 850 W (for a short time during start-up)
1070 x 545 mm
740 – 800 mm
1550 mm
82 dB/A
Max. sewing speed 3000 st./min. **
* Machine is preset for needle Nm. 160
** Do not exceed specified sewing speed due to the service life of the machine mechanism.
This cannot be guaranteed under any conditions. It is necessary to reduce speed depending on the thread, needle and material, stitch length and the foot track.
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 5
© ANITA
B SAFETY INSTRUCTIONS
Read the instructions carefully before installation and use. Keep this manual for future reference.
B1.
GENERAL INSTRUCTIONS
1.
Do not operate the sewing machine until proper preparation has been made by a technician or qualified person and safety precautions have been taken.
2.
Always follow the safety instructions when handling the machine.
3.
This sewing machine may only be operated by properly trained personnel.
4.
Maintenance, repair, inspection and adjustment of the machine may only be carried out by a qualified person.
5.
Work on electrical equipment may only be performed by a qualified worker or person with the appropriate authorization. Work on electric parts and equipment on your own is not permitted.
6.
The machine may only be used for its intended purpose.
7.
The warranty does not cover any problems in the operation of the machine that are caused by unauthorized modifications to the machine, as well as problems caused by non-observance of the instructions given in this manual and generally known habits for the operation and maintenance of industrial sewing machines.
B2.
INSTALLATION PRECAUTIONS
1.
Immediately report visible damage to the carrier. Check the contents of the order shipment and report any defects immediately to the manufacturer. Later claims will not be accepted.
2.
Use the machine after checking that it meets all the safety standards of your country.
3.
www.garudan.cz
and dust layer with a cloth or petrol before placing it on the work surface.
4.
The machine has been thoroughly inspected and tested before shipment. However, it may have been damaged by transport or impact. Check the operation of the machine with the handwheel, to detect extraordinary noises, heavy running, etc. before starting the test sewing.
5.
Never start the machine if the oil level is under or over the marked lines.
6.
Check that the power and phase are in accordance with the label instructions.
7.
Proper grounding of the machine is necessary.
8.
Use the correct grounding plug.
9.
Do not use an extension cord.
10.
Make sure that the power supply and voltage match the requirements on the label of the machine.
11.
Do not use the machine in explosive or corrosive environment.
12.
In the first two weeks, do not exceed 3/4 of the maximum machine speed.
13.
Check that the air pressure is between 0.55 and 0.6 MPa.
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 6
© ANITA
B3.
OPERATIONAL SAFETY INSTRUCTIONS
1.
Do not use the machine without a belt cover, finger guards or other protective equipment.
2.
All protective equipment of the machine must be in place before operation. Do not use the machine without covers and protective equipment.
3.
Repair damaged covers or replace them immediately.
4.
If the safety label is damaged, order a new one from the machine supplier and place it in its original position.
5.
Switch off the machine and unplug it in these situations (the motor still rotates after turning off; wait until it stops completely):
when threading the needle (needles), hooks, etc.
when changing the needle, presser foot, needle plate, hooks, hook bobbins, feeders, needle guards, finger guards, work guides, etc.
when the machine is not in use and left unattended
when opening or removing the protective covers
for any maintenance, repair, inspection and adjustment of the machine
when cleaning the machine
6.
Wear safety goggles and gloves when lubricating the machine. Do not drink oil under any circumstances, as it may cause vomiting and diarrhoea. Keep oil out of the reach of children.
7.
Take special care when lifting / tilting the machine head. When tilting the machine head, make sure the machine is turned off. Always hold the machine head with both hands.
8.
When handling cords and plugs, check if the machine is switched off to avoid electrical shock and injury.
9.
Check the electrical cords for damage to avoid injury by touching an exposed wire.
10.
Do not place any objects on the power cord.
11.
Do not open or touch the inside of the junction box.
12.
It is strictly forbidden to connect any connector while the machine is powered. Risk of damage to electrical components and drives.
13.
Do not modify the machine in any way that could endanger safety.
14.
www.garudan.cz
15.
Do not wipe the machine with thinner or acetone.
16.
Use only original or approved spare parts from manufacturer.
17.
Ensure adequate illumination of the work area and the surroundings of the machine.
18.
Disconnect the compressed air supply before servicing and repairing pneumatic equipment. Drain off the residual compressed air before servicing.
B4.
WORKING SAFETY INSTRUCTIONS
1.
Make sure you know the position of Stop button before starting to work.
2.
Do not touch any moving parts or put objects into the machine while sewing.
3.
Be careful not to catch or place objects near the machine's moving mechanisms, particularly fingers, sleeves, clothing and hair.
4.
Never touch the needle when the machine is turned on and sewing.
5.
Never reach under the thread lever cover while the machine is on.
6.
Do not place your fingers in the needle guard holder when feeding material manually.
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 7
© ANITA
7.
Do not work on the machine under the influence of alcohol or drugs.
8.
We recommend wearing safety goggles.
9.
Do not remove covers or any other safety device while the machine is running.
10.
Always turn off the main switch when leaving the machine.
B5.
DISPOSAL INSTRUCTIONS
For disposal of the machine contact your local dealer or manufacturer in accordance with legislation. www.garudan.cz
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 8
© ANITA
C1.
OIL SUMP INSTALLATION
C MACHINE SETUP
Insert rubber cushions ① , ③, ④ into the bedplate and tighten the screws ② .
Installation of the oil sump:
According to the picture fasten the oil sump
(5) to the plate with eight screws. www.garudan.cz
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 9
© ANITA
D OPERATING INSTRUCTIONS
D1.
REPLACING THE NEEDLE
Turn off the main power switch. Replace the needle only when the sewing machine is off.
For 1-needle machine GF-1130:
Turn the hand wheel to rise the needle bar 1 to the highest position.
Loosen the screw 2.
Pull out the needle from the needle bar 1 downwards.
Insert new needle into the opening in the needle bar 1 all the way up with the groove 3 to the right.
Tighten the screw 2.
For 2-needle machine GF-2230:
Turn the hand wheel (CCW) to rise the needle bar
1 to the highest position.
Loosen the screw 3.
Pull out the needle from the needle holder 2 downwards.
Insert new needle into the opening in the needle holder 2 all the way up with the groove of the www.garudan.cz
Tighten the screw 3.
When changing the needle size, you must adjust the distance of the hook to the needles, otherwise it will lead to malfunctioning:
Using the smaller size of the needle:
Skipping the stitches
Damaging the thread
Using the larger size of the needle:
Damaging of the tip of the hook
Damaging the needle
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 10
© ANITA
D2.
THREADING THE MACHINE
D2.1.
Threading the bottom thread
1. Pull the latch up ①.
2. Hold the bobbin with the loose end of the thread in a CCW direction and put it into the hook.
3. Pass the thread through the opening ② and ③ and under the bottom thread tension spring.
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 11
© ANITA
D2.2.
Winding the bobbin www.garudan.cz
1. Put the bobbin on the winding pin. Pass the thread through points ① to ③ and wind the end of the thread a few times around the bobbin.
2. Press the winder lever
Ⓐ
. Press the foot controller and machine will start winding. When the bobbin is full, winding stops automatically.
3. You can adjust the amount of thread by the metal plate screwed on to the winder lever A.
Loosen the screw and adjust position of the plate to stop winding at 80 % of the bobbin capacity.
4. It’s necessary to wind the thread evenly. Center the thread tension
Ⓒ
, adjust the position forward / backward and tighten the screw
Ⓓ
.
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 12
© ANITA
D2.3.
Threading the upper thread
1. Thread the upper (needle) thread of GF-1130-4412 MH as shown in the picture. www.garudan.cz
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 13
2. Thread the upper (needle) threads of GF-2230-4412 MH as shown in the picture.
© ANITA www.garudan.cz
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 14
© ANITA
D3.
ADJUSTING THE STITCH LENGTH AND REVERSE STITCH
1. Press the locking plate ③ and set the desired stitch length by turning the dial ①.
2. Press the reverse lever ②, the m achine will sew back. When the lever is released, the machine sews forward again.
D4.
THREAD TENSION ADJUSTMENT
D4.1.
Upper thread tension adjustment
Turn the thread tension nut ① clockwise to increase the tension. Turn the nut counterclockwise to decrease the tension. In double-needle machines, each thread has its own www.garudan.cz
D4.2.
Bottom thread tension adjustment
Turn the tension screw ② clockwise to increase the tension. Turn the screw counterclockwise to decrease the tension.
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 15
© ANITA
D5.
PRESSER FOOT
D5.1.
Presser foot lift
1. Raise the presser foot lever ① up to a height of 9 mm.
2. Lowering the lift lever will lower the foot.
3. You can also lift the presser foot up to 19 mm using the knee lever or by pressing the pedal backwards. Pressing the pedal backwards requires a pressurized air supply.
D5.2.
Foot pressure adjustment
The nut ② is used to lock the screw ① . Loosen it before adjusting the pressure and tighten again after www.garudan.cz
Turn the foot pressure screw ① clockwise to increase the foot pressure. Turn it counterclockwise to decrease the pressure.
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 16
© ANITA
D6.
HOOK SAFETY CLUTCH FUNCTION
During sewing, when the hook reaches beyond the limit, a safety lock is activated to lock it.
The needle will be still moving, but not the hook. Always remove the cause before running.
1. Press the button ① and turn the handwheel (CCW) until button ① clicks. Keep the button pressed and turn the handwheel backward (CW), until you hear a click.
2. Before running the machine motor in the usual way, check the proper functioning by turning the handwheel manually.
D7.
TIMING OF THE HOOK OPENER
www.garudan.cz
opener ① moves to the far right .
2. Push the hook ② in the direction of the arrow to bring it as close as possible to the hook opener ① until the nose ③ touches the groove on the needle plate ④.
3. Loosen the screw ⑤ and set the distance between the hook opener ① and the hook inner part Ⓐ to 0.1-0.3 mm.
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 17
© ANITA
D8.
TIMING OF THE HOOK AND THE NEEDLE
Make the settings below with the stitch length set to 0.
1. Turn the handwheel and raise the needle bar
2.3 mm from the lowest position. Check if the needle ② and the tip of the hook ③ align with each other. If not, loosen the two screws
④ of the small gear and rotate the hook to bring its tip to the center of the needle. We call this position "the machine at the set point of
2.3 mm."
2. Adjust the height of the needle bar to the point when “the machine is at the set point of
2.3 mm”, the hook tip is about 0.5 mm above the upper edge of the needle eye. Loosen the needle bar screw ①and adjust the distance between the upper edge of the needle eye ② and the hook tip ③ to 0.5 mm. Tighten the screw.
www.garudan.cz
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 18
© ANITA
3. To adjust the distance between the hook tip ③ and the needle ②, loosen the hook block screws ⑥ and the gear screws ⑤. Adjust the distance to 0.05-0.1 mm. Then tighten all screws.
4. Adjust the guard plate of the hook by bending it so that the distance between the plate ⑧ and the needle www.garudan.cz
The guard plate is intended to prevent contact of the needle with the hook tip, if the needle bends.
Adjust the distance when changing the needle size.
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 19
© ANITA
E MACHINE MAINTENANCE
.
E1.
LUBRICATING THE MACHINE
E1.1.
Lubricating the front part of the machine head
1. Loosen the front cover screws.
2. Remove the front cover.
3. Lubricate each day at the marked points.
4. Replace the cover.
5. Secure with screws.
E1.2.
Lubricating the machine head marked red. Add a few drops of oil to these points every day. If the machine oil could not use all the oil, decrease the frequency of the lubrication.
2. Before first use or after the long-term stop, lubricate the machine at marked points, remove cover ② and apply oil to each felt and hose.
3. "C" is the upper oil tank. Check the operation of the oil pump through the window.
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 20
© ANITA
E1.3.
Refilling the oil sump
1. Place the oil filter head ② on the hose ③ and put it into the oil sump ① as shown. You can attach it using the magnet.
2Add the oil until the cap ② is completely submerged.
www.garudan.cz
3. If the oil level falls below 1/3 of the head height ②, add more oil.
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 21
© ANITA
E2.
ADJUSTING THE LUBRICATION
E2.1.
Adjusting the lubrication of the hook
1. Loosen the nut ② and adjust the amount of lubrication with the screw ①. Turn the screw clockwise to decrease or counterclockwise to increase the amount of oil.
2. Test the proper amount of lubrication with a paper.
Place the paper close to the hook and bring the machine to maximum speed for a few seconds. You should see thin lines formed by the oil on the paper.
Too much oil Correct amount of oil Too little oil
E2.2.
Adjusting the lubrication of the upper oil tank www.garudan.cz
1. If too much oil accumulates in the upper oil tank, tilt the machine head and loosen the nut
① . T urn the screw ② counterclockwise. If the oil level is too low, turn the screw clockwise.
22 MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH
© ANITA
F TROUBLESHOOTING
Problem
1. Broken thread
(2 - 3 mm left on the bottom side)
Cause
1. Damage int the path of thread, damaged tip of the needle or the hook.
2. Upper thread tension is too high.
3. The needle is touching the tip of the hook.
4. Insufficient oiling of the hook.
5. Upper thread tension is too low.
6. The thread lever spring is too strong, the range of movement is too small.
7. Incorrect timing of the needle and hook.
Solution
1. Sand the surface with sandpaper. Sand the hook with a file.
2. Reduce the upper thread tension.
3. Adjust the distance between the needle and the
4. Adjust the amount of
5. Increase the upper thread tension.
6. Reduce spring force, increase the range of motion.
7. Adjust needle and hook
1. Incorrect timing of the needle and hook.
1. Adjust needle and hook
2. Foot pressure too low. 2. Increase the foot pressure.
2. Skipping stitches 3. Incorrect distance
3. Adjust the distance (see between needle eye and the hook tip.
4. Incorrect needle type.
www.garudan.cz
1. Bobbin tension spring too 1. Lower the bottom thread tight. tension.
3. Thread too tight
2. Threads are threaded incorrectly.
3. Bobbin doesn’t move .
4. Bottom thread tension is too low.
2. Check the threading of upper and bottom thread.
3. Check the bobbin.
4. Increase the bottom thread tension.
5. Bottom thread too thick. 5. Use the thinner thread.
6. Damaged tip of the needle.
6. Change the needle.
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 23
© ANITA
G DRIVE UNIT MANUAL
G1.
SAFETY INSTRUCTIONS
1) Read the manual carefully before installation and use.
2) Installation of the drive unit may only be carried out by a qualified person.
3) Follow all instructions indicated by symbols to avoid injury.
4) Do not use a multiple socket extension cord.
5) Make sure that the power supply and voltage match the requirements on the label of the machine.
6) Do not use in direct sunlight, outdoors and in the temperature over 45 °C or below 0 °C.
7) Do not use close to the heater. Humidity level must be between 30-95 %.
8) Do not use in dusty, corrosive or explosive environment.
9) Do not put heavy objects on the power cord, do not pull it or bend it.
10) Proper permanent grounding is necessary.
11) Use safety covers for all moving parts.
12) Do a test run at the slow speed and check the direction of the rotation.
13) Switch off the machine and unplug it in these situations:
• threading the needle (needles), hooks, etc.
• changing the needle, presser foot, needle plate, hooks, hook bobbins, feeders, needle guards, finger guards, work guides, etc.
• the machine is not in use and left unattended
• opening or removing the protective covers
• any maintenance, repair, inspection and adjustment of the machine
• cleaning the machine
14) Maintenance, repair, inspection and adjustment of the machine may only be carried out by a qualified person.
15) Use only original or approved spare parts from manufacturer.
16) Do not use heavy objects.
G2.
www.garudan.cz
The ASD58 series are power units that are designated to drive sewing machines and to be built into a sewing machine. They consist of the engine itself, the control box and the control panel (keypad). Other use is not permitted.
G3.
DRIVE UNIT TECHNICAL PARAMETERS
Product type
Voltage
Frequency
Max. power
ASD58-5 ASU58-55 ASD58-75 ASU58-75
AHE58-55
AC 23 0 ±20 % V
50/60 Hz
850 W
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 24
© ANITA
G4.
INSTALLATION
G4.1.
Connector description www.garudan.cz
Control box of the AS series
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 25
© ANITA
Connect the pedal and all connectors to the appropriate sockets as shown.
ATTENTION:
If you are unable to connect the connectors to the appropriate outlet, check the direction of the pins. Make sure you are plugging into the correct outlet.
G4.2.
Power supply and grounding
The grounding connection and checking of the correct connection parameters to the power supply may only be carried out by an electrician. The system ground - the yellow/green wire
- must be securely connected to electrical outlet to ensure safe operation and to prevent machine malfunctions.
ATTENTION: All wires must be connected separately to avoid overloading and safe operation of the machine!
G4.3.
Connecting and settings
For more information, consult the installation manual for your particular engine model.
Power unit control box installation www.garudan.cz
Make sure you have enough space on the right side of the plate to install the control box.
The control box is mounted on the right side under the plate.
To install the foot controller (pedal), make sure it is placed right under the power unit and attached to the underside of the plate. If necessary, loosen the screws, adjust the position and angle, and retighten.
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 26
© ANITA
G5.
CONTROL PANEL
G5.1.
Control panel display
The drive unit can be used with different models of sewing machines, which can have different optional functions as thread cutting, programmable back-tacking, automatic foot lift, etc.
If your machine is not equipped with this option, some of the features described below will not be available for your model. They are shown on the display, but the machine will not perform them.
Control panel layout www.garudan.cz
Symbols of the LCD display
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 27
© ANITA
Display icons description
No. Icon
1
2
3
4
5
6
7
8
9
Description
Automatic trimming
Slow start
No. Icon
10
11
Start back tacking 12
End back tacking
Sewing segment index
Numeric display
Foot lift after trimming
Foot lift after stopping
Needle down stop position
13
14
15
16
17
W sewing mode
Segment sewing
Multi-segment mode
Auto test
Description
Needle up stop position
Free sewing mode
Clamp function
Four-segment sewing www.garudan.cz
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 28
© ANITA
7
8
9
10
G5.2.
Operation panel keys description
Button
1
2
3
4
5
Name
Function
(Parameters)
Description
Use the button to select and confirm parameter settings and return to the sewing mode.
Start back tacking Selects and turns on the initial back tacking.
End back tacking
Free sewing mode
W sewing mode key
Selects and turns on the end back tacking.
Selects free sewing mode. The icon lights up on the display. Press the foot control to start sewing.
Press this key to enter the W sewing mode. LCD
6 Multi-segment sewing icon is on. In W sewing interface use the corresponding key „+“ or „ „ to set number of stitches of each segment (A, B, D) default range 1~F corresponds to the value 1~15.
Press this key to enter the multi-segment sewing mode. LCD icon is on. In multi-segment sewing interface use „+“ or „ „ key to set max. 24 segments. P01 is number of segments, -01 is current segment setting, -16 is number of stitches in the segment.
Press this key to enter the four-segment sewing Four-segment sewing mode. LCD icon is on. In four-segment sewing www.garudan.cz
„ „ key to set number of stitches of each segment (E, F, G, H) default range 1~F corresponds to the value 1~15.
Slow start
When the icon is lit, the slow start mode is on.
Press the key again for turning the slow start mode off.
Thread clamp
When the icon is lit, the thread clamp mode is on. Press the key again for turning the thread clamp mode off.
Set the stop position of the needle. When the icon Needle up/down stop position is lit, the needle stops up. When the icon , is lit, the needle stops down in the fabric. Note: you can select needle stop position directly as parameter
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 29
© ANITA
13
14
11
12
15
16
17
18
Stitch compensation
Trimming
H-43. Press + to enter the parameter.
Press for half stitch compensation. Press and hold for one stitch compensation. Hold for continuous compensational sewing.
Foot lift mode
One-step multi segment sewing
Lighting
When the icon is lit, auto trimming function is on. Press again for turning the function off.
Select the presser foot stop position up or down.
Pressing the key repeatedly you change foot position sewing mode.
When the icon is lit, pressing the foot control the machine performs whole preprogrammed sewing in one step.
Turning the light on/off.
Custom functions You can preset any custom function for this key.
Speed Increase or decrease the sewing speed or adjust the value.
Increase/decrease Increase or decrease parameter values. www.garudan.cz
MP04800EN,MP04900EN_200204 GF-1130-4412,GF-2230-4412 MH 30
Katalog náhradních dílů
Spare Parts List
GF-2230-4412 MH
ANITA B s.r.o.
Průmyslová 2453/7
680 01 Boskovice
Czech Republic tel: +420 516 454 774
+420 516 453 496 fax: +420 516 452 751 e-mail:
[email protected]
MP04900_200204
© ANITA
VERSION CREATED ON APPROVED BY
MP04900_200204 04. 02. 2020 Ing. Kamil Krátký www.garudan.cz
All rights reserved.
Property of Anita B s.r.o. and protected by copyright. The use of this content without written consent of Anita B s.r.o. is prohibited.
Copyright © Anita B s .r.o. (2020)
MP04900_200204 GF-2230-4412 MH 2
© ANITA
Content
www.garudan.cz
MP04900_200204 GF-2230-4412 MH 3
A. FRAME & MISCELLANEOUS COVER (1/2)
© ANITA www.garudan.cz
MP04900_200204 GF-2230-4412 MH 4
© ANITA
29
30
31
32
26
27
28
23
24
25
20
21
22
14
15
16
18
10
11
12
6
7
8
4
5
2
3
39
40
41
42
45
36
37
38
33
34
35
Ref. No
1
Parts No.
40016798
A. FRAME & MISCELLANEOUS COVER (1/2)
Name of parts Description
Face plate asm.
SS4111215SP Screw
40019114 Lubrication supplement
21331301 Top cover B
SS4110815SP Screw
21355904 Arm thread guide
SS7621040SP Screw
21331756 Window plate A asm.
21331202
21331806
21332002
Set screw
Window plate B
Window plate packing B
TA1050504R0 Rubber plug
TA0750704R0 Rubber plug
23208556
21332200
Auxiliary cover asm.
Oil baffle plate
21331608 Balance cover
SS7150910TP Screw
21355805 Thread guide
11/64-40 L=12
11/64-40 L=8
3/16-32 L=9.5
15/64-28 L=9
SS5090610SP Screw
B1129051000 Frame thread guide upper
9/64-40 L=6
SS2090710TP Screw 9/64-40 L=7.2
21408554 Thread guide asm.
21408505 Thread guide plate
17912106 Needle thread presser plate
B1132521000 Thread presser plate spring
SD0380551SL Hinge screw www.garudan.cz
SS2090710TP Screw 9/64-40 L=7.2
B3138512000 Take-up spring adjusting plate
SS7090520TP Screw
B1111563000 Bed slide spring
SS4110515SP Screw
21366406 Needle plate
SS2110920TP Screw
SS6090630SP Screw
SS6111140SP Screw
21365606 Bed slide (left) A
21361407
21365002
Bed support plate
Bed slide (right) A
23208507 Auxiliary cover
9/64-40 L=4.5
11/64-40 L=5
11/64-40 L=8.5
11/64-40 L=11
Note Qty
1
(1)
(1)
2
1
1
(1)
(1)
1
1
5
1
1
1
1
1
5
3
1
1
1
1
2
1
3
3
1
12
(2)
1
1
1
(1)
1
1
1
1
1
2
MP04900_200204 GF-2230-4412 MH 5
A. FRAME & MISCELLANEOUS COVER (2/2)
© ANITA www.garudan.cz
MP04900_200204 GF-2230-4412 MH 6
© ANITA
Ref. No
46
47
48
49
51
54
Parts No.
23208606
22602601
10201200A
22619100A
A. FRAME & MISCELLANEOUS COVER (2/2)
Name of parts Description
Sliding plate support
Bed screw stud
Rubber plug
Cap
EA9500B0100 Cable band
SS6151210SP Screw 15/64-28 L=12
Qty
(1)
2
1
1
1
2
Note www.garudan.cz
MP04900_200204 GF-2230-4412 MH 7
B. TAKE-UP AND UPPER SHAFT COMPONENTS (1/2)
© ANITA www.garudan.cz
MP04900_200204 GF-2230-4412 MH 8
© ANITA
Ref. No
1
25
26
27
28
22
23
24
19
20
21
16
17
18
12
13
14
15
9
10
11
6
7
8
4
5
2
3
35
36
37
38
39
32
33
34
29
30
31
B. TAKE-UP AND UPPER SHAFT COMPONENTS (1/2)
Parts No. Name of parts Description
010259 Upper shaft
21333000 Upper shaft front metal
B1905520000 Thread take-up lever
B1906051000 Take-up lever pin
B1907057000 Thrust pin
SS8150822TP
21339106
CQ303000000
CQ202000000
B1210051000
CQ505000000
21332507
SS8150822TP
SM8080812TP
21339502
SS8660810TP
21333109
CQ202000000
Screw
Needle bar crank rod
Oil wick
Oil wick
Needle bar crank pin
Oil wick
Counter weight (A)
Screw
Screw
Upper feed cam
Screw
Upper shaft inner metal
Oil wick
15/64-28 L=8
36 mm
15/64-28 L=8
M8x8
3.5
¼ -40 L=8
21336557
21336508
SS8660810TP
Eccentric cam A asm.
Eccentric cam A
Screw
21333703
22604904
Safety clutch disc
Upper sprocket
¼ -40 L=8
SS6661110SP
22604300
SS8150822TP
Screw 1/4-40 L=11
Timing belt
Screw www.garudan.cz
Bearing B 010262
010263 Bearing A
11/64-40 L=8 SS4110815SP
010258
21387501
B1214019000
010254
SS7151210SP
Screw
Screw
Lower sprocket
Sprocket ring
Bearing A
Screw
010256
0102445
Motor plate
Hand wheel
010255 Bearing B
MDBMASD58A850A Motor
LS5A16 Screw
15/64-28 L=14
1
1
1
1
1
1
4
4
Qty Note
1
1
1
1
1
1
1
0.45 m
0.03 m
1
1
1
2
2
1
2
1
0.15 m
1
1
2
1
1
2
1
2
1
1
1
2
1
MP04900_200204 GF-2230-4412 MH 9
B. TAKE-UP AND UPPER SHAFT COMPONENTS (2/2)
© ANITA www.garudan.cz
MP04900_200204 GF-2230-4412 MH 10
© ANITA
53
54
55
56
49
51
52
57
58
59
B. TAKE-UP AND UPPER SHAFT COMPONENTS (2/2)
Ref. No Parts No. Name of parts Description
40 010153 Belt cover
41 010426 Screw
42
43
44
SS8150710TP Screw
HX00123000A Cable clip
B1312563000A Safety clutch push button
15/64-28 L=7
46
47
48
RE0500000K0 E-ring
B1639051000 Spring
B1313055000 Safety clutch knob sleeve
SS8150710TP Screw
40038700 Thrust collar asm.
40038702 Thrust collar
SS8661030SP Screw
SB120000200 Bearing
SS7120760SP Screw
21353008 Horizontal feed cam cover
SS7110710SP Screw
TA0750704R0 Rubber plug
40016148 Collar B washer
15/64-28 L=7
1/4-40 L=10
20x42
3/16-28 L=7.0
11/64-40 L=7
Qty
1
(2)
1
2
1
2
1
(1)
2
1
1
1
1
1
1
1
4
1
Note www.garudan.cz
MP04900_200204 GF-2230-4412 MH 11
C. NEEDLE BAR ROCKING
© ANITA www.garudan.cz
MP04900_200204 GF-2230-4412 MH 12
© ANITA
Ref. No
1
25
26
27
28
22
23
24
19
20
21
16
17
18
29
30
31
32
12
13
14
15
9
10
11
6
7
8
4
5
2
3
Parts No.
21362504
21405204
22814909
B1437051000
SS8151150TP
22814909
B1401518000
B1411521000
SS7090910SP
B1412051000
21368451
C. NEEDLE BAR ROCKING
Name of parts Description
Needle bar frame
Hinge stud
Felt
Oil wick retainer
Screw
Felt
Needle bar
Needle rod holder
15/64-28 L=10.5
Screw
Felt
Needle clamp 3/8 asm.
9/64-40 L=8.5
SS6090410TP
MC372001600
B1467563000
SS7110910TP
Screw
Needle SY3355 160
Upper feed bar guide
Screw
9/16-40 L=3.5
11/64-40 L=8.5
21388400 Rocking base guide
SS7110830SP Screw 11/64-40 L=7.5
21338603 Rocking front arm
SS6091022TP Screw
21338801 Rocking front arm
SM8080812TP Screw
21338900 Rocking shaft
B1414232000 Square block
B1410771000
21339304
40027746
Stud
Rocking shaft front metal
Bushing rear www.garudan.cz
Rocking rear arm asm. 21339056
21339007 Rocking rear arm
SS6152440SP
21347406
EA9500B0100
CQ202000000
Screw
Rocking rear arm felt
Cable band
Oil wick
15/64-28 L=23.5
Qty Note
1
1
1
1
1
1
1
1
1
1
1
2
2
1
2
1
2
1
2
1
2
1
1
1
1
1
1
1
1
1
2
0.05 m
13 MP04900_200204 GF-2230-4412 MH
D. PRESSURE ADJUSTING & UPPER FEED MECHANISM (1/3)
© ANITA www.garudan.cz
MP04900_200204 GF-2230-4412 MH 14
© ANITA
Ref. No
1
25
26
27
28
22
23
24
19
20
21
16
17
18
12
13
14
15
9
10
11
6
7
8
4
5
2
3
35
36
37
38
39
32
33
34
29
30
31
40018341
40033030
B14670530A0
B1468053000
SS6151780SP
21406509
26225201
SS6151920SP
SS7150740SP
10714608
10714509
B1501241H00
B1510155000
SS8150822TP
40033027
40033026
21347109
EA9500B0000
40018340
SD0640701SP
B1414555000
WP0501046SC
40033029
SS7110510SP
10509701
21337803
21372651
21367958
SS6090910TP
SM8050602TP
40033032
D. PRESSURE ADJUSTING & UPPER FEED MECHANISM (1/3)
Parts No. Name of parts Description
21340401 Upper feed shaft
21340500 Upper feed front arm
SS8660612TP
21341904
21378302
Screw
Front metal
Feed shaft metal
1/4-40 L=6
229044155
22904106
SS8660610TP
Main shaft thrust collar asm.
Main shaft thrust collar
Screw 1/4-40 L=6
15/64-28 L=7 Screw
Upper feed link asm.
Upper feed link
Felt
Clip
Screw
Screw
Slide block
Washer
Triangular lever asm.
Screw
Felt
Feed adjusting base support
Walking bar driving link
Walking bar A
Walking bar asm.
Upper feed guide plate
Roller
Screw
Screw
Support pin
Connection link B
Presser bar
Presser bar lower bushing
Walking foot 1-1/4 asm.
Presser foot asm.
Screw
Screw
Presser bar holder A asm.
CV-70S
5x13x1
11/64-40 L=5
15-64-28 L=19
15/64-28 L=7
9/64-40 L=9
M5 L=6
1
4
1
1
2
1
1
1
Qty Note
1
1
2
1
1
1
1
2
1
1
1
1
2
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
MP04900_200204 GF-2230-4412 MH 15
D. PRESSURE ADJUSTING & UPPER FEED MECHANISM (2/3)
© ANITA www.garudan.cz
MP04900_200204 GF-2230-4412 MH 16
© ANITA
Ref. No
40
64
65
66
67
61
62
63
58
59
60
55
56
57
51
52
53
54
48
49
50
45
46
47
41
42
43
44
74
75
76
77
78
71
72
73
68
69
70
D. PRESSURE ADJUSTING & UPPER FEED MECHANISM (2/3)
Parts No. Name of parts Description
40033031 Presser bar holder A
SS7110910TP
21340906
22907604
B1502246000
SD0800481SP
21341151
B1462053000
21406103
21406608
SS8660810TP
10713808
21340302
SM6052002TP
010464
21048707
21340005
10774354
RE0800000K0
NS6680320SP
10715100
Screw
Presser adjusting screw
Presser spring regulator nut
Presser spring
Hinge screw
Holding plate complete
Thread release spring
Presser lifter lever
Guide plate spacer
Screw
Connection link pin B
Upper feed rear arm (B)
Scerw
Screw
Hinge screw
Upper feed link (B)
Upper and lower dial asm.
E-shaped snap ring
Nut
Vertical dial shaft bushing
11/64-40 L=8.5
D=8 H=4.9
1/4-40 L=8
M5 L=20
M8 L=10
8 mm
9/32-28
10715001
10715704
Vertical adjusting cam
Vertical dial pin
B152652700G
SS6110630TP
21341607
Spring
Screw
Vertical adjusting arm
11/64-40 L=6 www.garudan.cz
Pin 10715308
SM6051402TP Screw M5x0.8 L=14
21341508
10718203A
10714202
21438106
SM1050801SR
21339700
SS4110815SP
10713501
10716504
B3416552000
RE0500000K0
Vertical change base shaft
Feed shaft front metal
Vertical change belt
Stopper plate B
Screw
Upper feed stopper plate (B)
Screw
Spring hook
Vertical shaft spring
Connecting rod hinge hook
E-ring
M5 L=8
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
1
1
1
1
1
(1)
1
1
1
1
1
1
2
Qty Note
1
1
1
1
1
1
1
1
MP04900_200204 GF-2230-4412 MH 17
D. PRESSURE ADJUSTING & UPPER FEED MECHANISM (3/3)
© ANITA www.garudan.cz
MP04900_200204 GF-2230-4412 MH 18
© ANITA
Ref. No
79
80
81
D. PRESSURE ADJUSTING & UPPER FEED MECHANISM (3/3)
Parts No. Name of parts Description
21339809 Upper feed dog spring hook
SS7110830SP
10713766A
Screw
Eccentric rod (set)
11/64-40 L=7.5
Qty Note
1
1
1 www.garudan.cz
MP04900_200204 GF-2230-4412 MH 19
E. FEED MECHANISM (1/2)
© ANITA www.garudan.cz
MP04900_200204 GF-2230-4412 MH 20
© ANITA
Ref. No
1
25
26
27
28
22
23
24
19
20
21
16
17
18
12
13
14
15
9
10
11
6
7
8
4
5
2
3
35
36
37
38
39
32
33
34
29
30
31
Parts No.
21364252
21364203
10107902
SS9151440CP
WP0621016SD
SM8050502TP
B1604012000A
RE0500711KP
CQ202000000
21364104
SS7111410SP
22609408
21378302
020514
22609309L
SS6121610TP
22904155
22904106
SS8660610TP
10205201
SD0900701TP
E. FEED MECHANISM (1/2)
Name of parts Description
Feed base asm.
Feed base
Feed bar fork
Screw
Washer
15/64-28 L=14
6.2x13x1
Screw
Feed bar shaft
Snap ring 5
Oil wick
Feed rocker
Screw
Feed rock shaft
Feed shaft metal
Screw
Feed rocker shaft crank
Screw
Main shaft thrust collar asm.
Main shaft thrust collar
Screw
Needle bar frame rod
Hinge screw
M5 L=5
11/64-40 L=14
11/64-40 L=8.5
3/16-28 L=15.5
1/4-40 L=6
D=9 H=7
NS6680320SP Nut 9/34-28
21337506 Feed adjusting base
21337704
21337407
SS7110910TP
Feed adjusting base cover
Screw
Square block
11/64-40 L=8.5 www.garudan.cz
Feed adjusting base support 21337803
SS8150822TP Screw 15/64-28 L=8
21338306
SS5090610SP
21337902
Felt support
Screw
Eccentric pin
9/64-40 L=6
SS709010TP
21337308
SD0800402TP
21337605
21338009
SS7111410TP
21337209
B1610512000
Screw
Feed adjusting rod
Hinge screw
Spring hook
Screw
Feed adjusting A
Feed driving slide block
Screw
9/64-40 L=8.5
D=8 H=4
11/64-40 L=16
M6 L=18
2
1
1
1
2
1
1
1
Qty Note
1
1
1
(1)
(1)
(1)
1
1
0.14 m
1
2
1
1
2
1
1
2
(1)
(2)
1
1
1
1
2
4
2
2
2
1
2
1
MP04900_200204 GF-2230-4412 MH 21
E. FEED MECHANISM (2/2)
© ANITA www.garudan.cz
MP04900_200204 GF-2230-4412 MH 22
© ANITA
Parts No.
SM6061802TP
SD1000801SH
21336300
SS6580752TP
CS1201010SH
CS1201011SH
SS8660610TP
RE0900000K0
21388004
SS6120930TP
22814909
NS6080210SP
SS6081810SP
020568
010561
010562
21336805
21366901
SS6121860SP
11009909
R0092270200
22912000
22912109
21336656
21336607
B1418761000
CQ202000000
SM8050502TP
21336706
21338207
Ref. No
40
64
65
66
67
61
62
63
68
69
58
59
60
55
56
57
51
52
53
54
48
49
50
45
46
47
41
42
43
44
Screw
E. FEED MECHANISM (2/2)
Name of parts Description
M6 L=15
Feed dial A
Feed dog
Screw
Feed regulator screw
Rubber ring
Feed regulator pin
Feed regulator pin spring
3/8
3/16-28 L=18
Feed link asm.
Feed link
Connecting forked link pin
Oil wick
Screw
Feed rod A
Feed link pin
Hinge screw
Backward feed lever shaft
Screw
Thrust collar asm.
Thrust collar
Screw
E-ring
Reverse feed control lever
Screw
M5x6
D=10 H=8
1/8-40 L=7
D=12 W=10
D=12 W=10
1/4-40 L=6
9
3/16-28 L=9
Screw
Feed shaft metal
Bottom
Spring
1/8-44 L=18
Qty Note
1
1
1
1
1
1
1
1
1
(1)
1
0.04 m
1
1
1
1
1
2
1
(1)
(2)
1
1
2
1
1
1
1
1
1
MP04900_200204 GF-2230-4412 MH 23
F. HOOK SHAFT & LOWER FEED MECHANISM (1/2)
© ANITA www.garudan.cz
MP04900_200204 GF-2230-4412 MH 24
© ANITA
Ref. No
3
31
33
35
36
28
29
30
25
26
27
21
23
24
17
18
19
20
13
14
15
9
11
12
7
8
4
6
45
46
47
48
49
40
42
44
37
38
39
F. HOOK SHAFT & LOWER FEED MECHANISM (1/2)
Parts No. Name of parts Description
21335104 Hook shaft base (right)
21362108 Hook shaft base (left)
21334909 Bobbin case opening lever link
B1821051000 Crank screw stud
CQ202000000 Oil wick
11/64-40 NS6110420SP
B1822563000
SS8110422TP
B1823051000
SS7111810TP
CQ202000000
B1824563000
WP0371016SD
SS6090810SP
10111102
10112704
21378500
2134701
10109908
10112407
SS6153040SP
Nut
Bobbin case opening lever crank
Screw
Opening lever crank pin
Screw
Oil wick
Bobbin case opening lever
Washer
Screw
Thrust washer
Thrust washer
Hook shaft upper metal
Hook shaft lower metal
Saddle installing block upper
Saddle installing block lower
Screw
11/64-40 L=4
11/64-40 L=18
3.7x8x1
9/64-40 L=7.5
1.3
1.8
15/64-28 L=30
WP0850002SP Washer 8.5x18x1.6
SM6082502TP Screw M8 L=25
B1834512000A Oil adjusting screw
NS6110420SP
B18305630A0
Nut
Vertical-axis sewing hook asm.
11/64-40 www.garudan.cz
Bobbin B9117563000
21361704 Lower shaft
B18025120A0A Bushing asm. Front
SS8151150TP
B18035150A0
Screw
Bushing asm. Intermediate
15/64-28 L=10.5
SS8151150TP
22609804
SS8660530TP
B1817051000
SS8660670SP
SS8660530TP
B1816051000
SS8660810TP
Screw
Feed driving cam
Screw
Hook driving shaft gear small
Screw
Screw
Hook driving shaft gear large
Screw
15/64-28 L=10.5
1/4-40 L=4.5
1/4-40 L=6.1
1/4-40 L=4.5
1/4-40 L=8
2
2
2
2
1
1
1
4
Qty Note
1
1
1
2
0.02 m
2
2
4
2
2
0.02 m
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
MP04900_200204 GF-2230-4412 MH 25
F. HOOK SHAFT & LOWER FEED MECHANISM (2/2)
© ANITA www.garudan.cz
MP04900_200204 GF-2230-4412 MH 26
© ANITA
Ref. No
50
58
59
60
61
55
56
57
51
52
53
54
F. HOOK SHAFT & LOWER FEED MECHANISM (2/2)
Parts No. Name of parts Description
SS8151150SP Screw
SQ1110401MZ
22611909
SS8660530TP
22611701
10109700
10109809
10110906
Connecting screw
Oil pump shaft
Screw
Plunger bushing B
Thrust washer A
Thrust washer B
Bushing thrust
15/64-28 L=10.5
1/4-40 L=4.5
1.1
10111003
10111201
10112506
10112605
Thrust washer
Thrust washer F
Thrust washer
Thrust washer
1.2
1.6
1.7
2
2
2
2
Qty Note
1
4
1
3
1
2
2
2 www.garudan.cz
MP04900_200204 GF-2230-4412 MH 27
G. THREAD TENSION COMPONENTS
© ANITA www.garudan.cz
MP04900_200204 GF-2230-4412 MH 28
© ANITA
Ref. No
1
25
26
27
28
22
23
24
19
20
21
16
17
18
32
33
34
29
30
31
35
12
13
14
15
9
10
11
6
7
8
4
5
2
3
Parts No.
21390562
B3128051000
10124501
21390554
21441100
SD0470281SP
B3127527000
B3127051000
G. THREAD TENSION COMPONENTS
Name of parts Description
Thread tension asm.
Thread take-up spring A
Thread take-up spring stud
Thread tension base complete
Thread release plate
Hinge screw
Pin B
Tension release pin short
D=4.7 H=2.8
NS6110310SP Nut 11/64-40
10124204 Thread tension post A
B3214047000 Bobbin winder tension disc
D3168555H0B Tension spring No.1
11072402 Thread tension nut
10124303 Thread tension post B
B3126051000 Tension disc
B3132051000 Tension disc holder
B3129053000 Tension spring
B3120125000 Rotating stopper
11072204 Tension nut
B3143527000 Take-up spring guide stud
B31375270A0 Take-up spring guide asm.
B3142527000 Take-up spring guide plate
B3139527000 Collar
B3128527000
22617609
22618904
Thread take-up spring B
Thread tension post
Set screw www.garudan.cz
Set screw 22618904
B3138527000 Adjusting plate B
SS7090520SP
B3141527000
B3125527000
B3125012000
SS7110910TP
21348206
PS0600502KP
Screw
Presser Collar
Take-up spring guide
Thread tension nut
Screw
Tension release bar
Spring pin
9/64-40 L=4.5
11/64-40 L=8.5
1
2
1
1
1
1
1
1
1
1
1
Qty Note
1
1
1
1
1
2
1
1
2
1
4
2
2
1
4
2
2
2
2
1
2
1
1
1
MP04900_200204 GF-2230-4412 MH 29
H. LOWER THREAD WINDER MECHANISM COMPONENTS
© ANITA www.garudan.cz
MP04900_200204 GF-2230-4412 MH 30
© ANITA
Ref. No
1
25
26
27
28
22
23
24
19
20
21
16
17
18
29
30
31
32
12
13
14
15
9
10
11
6
7
8
4
5
2
3
H. LOWER THREAD WINDER MECHANISM COMPONENT
Parts No. Name of parts Description
21357967 Bobbin device asm.
22537658 Bobbin fitting basis complete
21357959 Bobbin shaft complete
22538151 Bobbin cam shaft complete
23636202 Bobbin lever
21356001 Adjusting plate
B152989000CA Pressure foot spring
10618304 Vertical roller washer
21358205 Bobbin friction gear
B3205210000 Cushion
B1148555000 Spring
RC0560711KP Retaining ring
RE0500000K0 E-ring
R0092270200
SS7091410SP
Rubber ring
Screw 9/64-40 L=13.5
SS6090520SP
14512503
SS6110810TP
10704807
SM8050602TP
10502300
Screw
Bobbin adjusting plate
Screw
Bobbin friction wheel
Screw
Thread cutter
9/64-40 L=5.0
11/64-40 L=8
M5 L=6
SS6090620SP
21355755
Screw
Lower thread guide asm.
9/64-40 L=6
21355706 Fitting base
S3162555B00
NS6110310SP
D3168555H0B
Thread guide
Nut 11/64-40 www.garudan.cz
Tension spring No.1
B3214047000 Bobbin winder tension disc
21378708
11072402
SM6040800SP
22538706
Thread tension post
Thread tension nut
Screw
Packing
1
2
1
1
2
1
1
1
2
1
1
1
3
1
1
2
1
Qty Note
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
31 MP04900_200204 GF-2230-4412 MH
I. AUTOMATIC PRESSER LIFTING MECHANISM
© ANITA www.garudan.cz
MP04900_200204 GF-2230-4412 MH 32
© ANITA
Ref. No
1
12
13
14
9
10
11
6
7
8
4
5
2
3
Parts No.
I. AUTOMATIC PRESSER LIFTING MECHANISM
Name of parts Description
ACQ40x15 Air cylinder
SM6082002TP Screw M8 L=20
21356506 Cylinder Connecting screw
NM6080001SE
SD0720331SP
21356605
21356803
SM6051002TP
21356704A
SPL4-01
21356308
Nut
Hinge screw
Lever A
Lever B
Screw
Shaft
Elbow
Cylinder stay (front)
M8
D=7.24 H=3.3
M5x0.8 L=10
21356407
SS6151040SP
21356704B
Cylinder stay (rear)
Screw
Nut
15/64-28 L=10
Qty Note
1
4
1
1
1
1
1
2
1
2
1
1
4
1 www.garudan.cz
MP04900_200204 GF-2230-4412 MH 33
J. LUBRICATION COMPONENTS (1/2)
© ANITA www.garudan.cz
MP04900_200204 GF-2230-4412 MH 34
© ANITA
Ref. No
1
25
26
27
28
22
23
24
19
20
21
16
17
18
12
13
14
15
9
10
11
6
7
8
4
5
2
3
35
36
37
38
39
32
33
34
29
30
31
Parts No.
21345756
21345707
21345806
21345905
21346358
21346309
21346507
21346408
EA9500B0000
SS7110710SP
21340708
010624
CQ202000000
21347000
CQ202000000
21347208
SS3090610SP
21346002
B1412051000
BT0600402EA
B3538112000
J. LUBRICATION COMPONENTS (1/2)
Name of parts Description
Arm once through oil felt asm.
Arm once through felt A
Felt B
Face once through felt
Felt support asm.
Felt
Feed change felt
Felt
Clip
Screw
Upper feed oil bar plate
Nut 11/64-40
Oil wick
Take-up oil plate
Oil wick
Take-up lubrication felt
Screw
Felt
Felt
Oil tube
Oil return tube holder
CV-70S
11/64-40 L=4.3
9/64-40 L=6
SS4110615SP
40051503
Screw
Arm oil tank asm.
11/64-40 L=6
B3520586000 Oil sight window
21345608
SQ1110401MZ
SQ1150451MZ
Arm oil tank
Connecting screw www.garudan.cz
Connecting screw
23630007 Tube
23630007
23630007
CQ252000000
EA9500B0100
SS7110830SP
21345103
SS4150915SP
21345202
SS4150915SP
010623
021365
Tube
Tube
Oil wick
Cable band
Screw
Lubrication bracket
Screw
Oil pipe stay
Screw
Screw
Filter
11/64-40 L=7.5
15/64-28 L=9
15/64-28 L=9
MP04900_200204 GF-2230-4412 MH
2
1
2
1
1
0.2 m
0.6 m
0.7
3
1
1
2
1
1
1
2
3
0.5 m
1
1
1
1
0.1 m
2
Qty Note
1
1
1
1
1
1
1
1
2
2
1
1
0.2 m
1
0.2 m
35
J. LUBRICATION COMPONENTS (2/2)
© ANITA www.garudan.cz
MP04900_200204 GF-2230-4412 MH 36
© ANITA
Ref. No
40
51
52
53
54
48
49
50
45
46
47
41
42
43
44
55
56
57
58
59
Parts No.
021364
021363
021360
B3534155000
B1214038000
B3524552000
SS4110815SP
SS6111010SP
23630007
23630007
LM8
23630007
23630007
21338306
SS5090610SP
SS5090610SP
21346606
23630007
PS0500202KP
CQ202000000
J. LUBRICATION COMPONENTS (2/2)
Name of parts Description
Cover
Oil filter head
Throttle sleeve
Plunger
Plunger spring
Plunger thrust plate
Screw 11/64-40 L=8
Screw 11/64-40 L=9.5
Tube
Tube
Nut
Tube
Tube
Lubrication felt presser
Mutual vertical change felt
8
Screw
Pipe support
Tube
Spring pin
Oil wick
3/16-28 L=7
5x20
Qty Note
1
1
1
1
1
1
1
2
0.36 m
0.08 m
1
0.1 m
0.5 m
1
1
1
1
0.22 m
1
0.2 www.garudan.cz
MP04900_200204 GF-2230-4412 MH 37
K. THREAD STAND COMPONENTS
© ANITA www.garudan.cz
MP04900_200204 GF-2230-4412 MH 38
© ANITA
Ref. No
1
Parts No.
26910158
K. THREAD STAND COMPONENTS
Name of parts Description
Thread standing device asm.
Qty Note
1 www.garudan.cz
MP04900_200204 GF-2230-4412 MH 39
L. AIR MECHANISM COMPONENTS
© ANITA www.garudan.cz
MP04900_200204 GF-2230-4412 MH 40
© ANITA
Ref. No
1
12
13
14
15
9
10
11
16
6
7
8
4
5
2
3
Parts No.
021724
021723
021703
021704
021705
SPC8-01
SPL6-01
WP0621016SH
LM6
040151
022236
APU0604 L=500
APU0425 L=500
021658A
SS4110815SP
021726
L. AIR MECHANISM COMPONENTS
Name of parts Description
Air apparatus (B) asm.
Mounting panel
Screw
Screw
Filter regulator
Nipple
Nipple
Flat pad
D=4.1 L=20
M6 L=10
Nut
Screw
Electromagnetic valve asm.
Tube ø6
Tube ø4
Safety switch
Screw
Pipe clamp
1
2
1
3
2
3
1
1
Qty Note
1
1
2
2
1
1
1
2 www.garudan.cz
MP04900_200204 GF-2230-4412 MH 41
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project