Kontron CP3-SVE-M76AC-230 75Watt AC Power Supply Datasheet

CP3-SVE-M76AC-230

Power supply for low power CPCI systems

ˆ

75 Watt AC/DC with M-connector and front input



230 V AC input voltage



3.3 V and 5 V DC output



75 Watt output power



3U/8HP front panel



Power input via front

CP3-SVE-M76AC-230

75 W AC/DC for low power CPCI systems

The product description provided with this data sheet is regarded as part of the general Kontron CPCI Power Supply manual ID 24139.

For further information, in particular general details as well as disclaimer, safety and warranty statements, refer to the CPCI Power

Supply Manual.

This power supply is designed for use with standard CPCI systems as well for integration in electronic or electrical enclosures, e.g.

Kontron’s 19” racks.

TECHNICAL INFORMATION

FORM FACTOR

FRONT PANEL SIZE

HEIGHT OF POWER SUPPLY UNIT

WIDTH OF POWER SUPPLY UNIT

DEPTH OF POWER SUPPLY UNIT

MECHANICS

PLUG-IN COMPATIBILITY

POWER SUPPLY CONNECTOR

INPUT VOLTAGE

INPUT FREQUENCY

OUTPUT VOLTAGES / CURRENTS

OUTPUT POWER

TOTAL MINIMUM OUTPUT LOAD

COOLING FORCED AIR COOLING

REDUNDANT SUPPLY

CAPABILITY

STATUS INDICATION

SPECIAL FEATURE(S)

3U

40.3 mm x 128.4 mm

3U (128 mm)

8HP (40 mm)

171.9 mm (without connector and handle)

19” rack yes

DIN M24/8 connector

230 VAC

47 … 63 Hz

V1 = +5.1 V, max. 8.0 A

V2 = +3.3 V, max. 8.0 A

V3 = +12 V, max. 0.15 A

75 W

0 W

≥ 0.5 m/s recommended

-

Separate LEDs for V1 and V2

None

// 2

// View of Power Supply Unit CP3-SVE-M76AC-230 www.kontron.com

PIN

A.18

A.19

A.20

B.13

B.14

A.14

A.15

A.16

A.17

2

5

11

A.13

B.15

B.16

DIN M24/8 POWER SUPPLY CONNECTOR

The AC power input is via the front panel connector. The V1 ... V3 output voltages from the power supply unit to the backplane are connected via a 32-pole DIN 24/8 male power supply connector.

For the pinouts of the DIN M24/8 power supply connector please refer to the following table.

FUNCTION

NC

NC

PE

NC

NC

NC

OVF

+5 VF

+3.3 VL

+12 VL

NC

+3.3 VL

+3.3 VL

+3.3 VL

+3.3 VL

PIN

C.17

C.18

C.19

C.20

22

C.13

C.14

C.15

C.16

B.17

B.18

B.19

B.20

25

FUNCTION

+3.3 VL

+3.3 VL

+12 VL

NC

NC

NC

NC

+3.3 VL

+3.3 VL

+3.3 VL

+12 VL

NC

+5 VL

OVL

// Orientation of the DIN M24/8 Power Supply Connector

FRONT PANEL AC INPUT POWER CONNECTOR: PINOUT

This connector is available for applications requiring input power from the front of the chassis. This is a Phoenix, 3-contact connector (GMSTB 2,5/ 3-GF-7,62). This connector is not designed for

“hot-plugging”. The figure and table nearby provide pinout information.

PIN

1

2

3

SIGNAL

L

N

PE

LINE INPUT CONNECTOR: PINOUT

This connector is the complementary connector for the application side for connecting to this power supply and is delivered with the power supply. This is a Phoenix, 3-contact plug type connector

(GMSTB 2,5/ 3-STF-7,62). The figure and table nearby provide pinout information.

PIN

1

2

3

SIGNAL

L

N

PE www.kontron.com

// 3

INSTALLATION

Thanks to its plug-in compatibility this DIN M-type power supply unit allows for an easy installation, by which the power supply unit’s male DIN M24/8 power connector is inserted into the backplane’s mating female connector without the need of any intermediate adaptation.

ELECTRICAL SPECIFICATION

INPUT

INPUT VOLTAGE

EFFICIENCY

INRUSH CURRENT LIMITATION

FUSE

HOLD-UP TIME

OUTPUT

OUTPUT POWER V1 (5.1 V)

OUTPUT POWER V2 (3.3 V)

OUTPUT POWER V3 (12 V)

RIPPLE

TOTAL OUTPUT LOADS

STATUS INDICATION

RISE-DELAY TIME

START-UP TIME

REGULATION

LINE REGULATION

LOAD REGULATION

PROTECTION AND CONTROL

OVERVOLTAGE PROTECTION

OVERLOAD PROTECTION

230 VAC, 50/60 Hz, range 184..264 VAC

>80 % (typical)

≤ 25 A peak

≤ 35 A peak

cold

warm

3.15 AT (internal, not user serviceable)

> 35 ms at 100 % load voltage: 5.1 V, +5/-3% (including ripple and noise) current: min 0.0 A; nominal 8.0 A; peak 12 A for 100 ms voltage: 3.3 V, +5/-3% (including ripple and noise) current: min 0.0 A; nominal 8.0 A; peak 12 A for 100 ms voltage: 12 V, +8/-7% (including ripple and noise) current: min 0.0 A; nominal 0.15 A; peak 0.2 A

V1, V2: < 50 mVpp, V3: < 200 mVpp min 0 W; max 75 W for all outputs green LEDs for V1, V2

< 1 s at 230 VAC

≤ 15 ms

< 0.2 % for V1, V2 at a load of 8.0 A each

< 0.5 % for V1, V2

125 % ± 5 % for V1, V2

Current limitation: >150 % I

Rated

for V1, V2

Thermal shutdown with auto-restart for V3

Output permanent short-circuit proof

Switches off if inside temperature becomes too high, restart with hysteresis OVER TEMPERATURE

PROTECTION

ENVIRONMENT

OPERATING AMBIENT

TEMPERATURE

DERATING

CLIMATIC HUMIDITY

RECOMMENDED AIRFLOW

EMC

INTERFERENCE SUPPRESSION/

IMMUNITY

INTERFERENCE EMISSION

SAFETY

0 °C to + 55 °C (without derating)

0 °C to + 70 °C (with derating)

2.0 % / °K between 55 °C and 70 °C

93 % RH at 40 °C, non-condensing

(acc. to IEC 60068-2-78)

≥ 0.5 m/s

EN 61000-6-2:2005/AC:2005, EN 61000-6-1:2007

EN 61000-6-3:2007 +A1:2011/AC:2012; EN 61000-6-4:2007 +A1:2011

EN 62368-1:2014, IEC 62368-1:2014 (Second Edition)

WARNING!

Adequate thermal cooling of the power supply must be ensured.

Therefore do not obstruct or hinder cooling air circulation or heat conduction within the power supply or surrounding equipment.

Failure to comply with this warning may result in damage to your equipment.

// 4 www.kontron.com

OUTPUT POWER DIAGRAMS

// Signal when switched on

ORDERING INFORMATION

ARTICLE

CP3-SVE-M76AC-230

DESCRIPTION

CompactPCI Power-Supply 75 W, 230 VAC, Out:+3.3 V/8 A, +5 V/8 A, 12 V/0,15 A.

M24/8 type backplane connector, 8HP/3U front panel, Power input on Front connector, LED Indicator.

Replacement of CP3-SVE-M76AC

GLOBAL HEADQUARTERS

Kontron Europe GmbH

Gutenbergstraße 2

85737 Ismaning, Germany

Tel.: + 49 821 4086-0

Fax: + 49 821 4086-111 [email protected]

www.kontron.com

// 5