- Home
- Home security & automation
- Security device components
- THEBEN
- compact passage 24V SR
- Operating instructions
Theben compact passage 24V SR Operating Instructions
Add to My manuals19 Pages
THEBEN compact passage 24V is a high-quality presence detector that can be used for a variety of applications. The device has a long service life and is easy to use.
The compact passage 24V has a 360-degree horizontal range at a 2-3.5m mounting height. It is equipped with mixed light control, which allows it to operate in both natural and artificial light conditions.
The switch-off delay for light can be set between 10 seconds and 20 minutes, and the switch-off delay for presence can be set between 10 seconds and 120 minutes. The switch-on delay for presence can be set between 0 and 10 minutes.
advertisement
Presence detector
compact passage 24V
Art. Nr. 201 4 090
E
I
NL
D
F
GB
Bedienungsanleitung 2
Notice d´utilisation 22
Installation manual 42
Manual de instrucciones 62
Istruzioni per l'uso 82
Gebruikershandleiding 102
English Installation manual
Presence detector
compact passage 24V
Table of contents
1. Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
2. Function and performance characteristics. . . . . . . . . . . . . . . . . . . . . . . 44
3. Fitting and connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4. Start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
5. Parallel circuit operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
6. Test Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
7. Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
8. Warranty declaration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
9. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
42
Thank you for purchasing an Theben HTS presence detector and putting your trust in us.
1. Safety
Familiarise yourself with the compact passage 24V before assembly and start-up by reading this operating instructions.
IMPORTANT!
The unit requires no maintenance. Opening the unit or inserting foreign bodies into it will invalidate the warranty.
Proper use
The presence detector serves exclusively for the purpose contractually agreed between the manufacturer and the user. Any other use is regarded as improper. The manufacturer is not responsible for any resulting damage.
43
GB
2. Function and performance characteristics
The presence detector compact passage 24V detects persons within a corridor. Simultaneously, its light sensor measures the brightness in the room and compares it to the pre-set brightness threshold.
The switching contact A «Light» switches on the lighting in case of presence and insufficient brightness, and off in case of absence or sufficient brightness.
● Switching contact „Light”: potential-free relay
● Adjustable brightness threshold and switch-off delay
● Suitable for fluorescent and compact energy saving lamps as wells as for halogen and incandescent lamps
● Pulse function for staircase lighting timer
● SendoPro 868-A management remote control (optionally)
The switching contact B «Presence» controls heating, ventilation and air-conditioning systems. The contact closes in case of presence, a switchon delay allows a delayed switching on. The contact can also be used for room surveillance purposes. Using reduced sensitivity, it only responds on very distinct movements.
● Switching contact „Presence“: potential-free relay
44
● Adjustable switch-on delay and switch-off delay
● Surveillance function
3. Fitting and connection
3.1 Presence detection
The ideal mounting height is 2 m - 3,5m.
The sensitivity of the detector decreases with increasing mounting height.
The detection ranges of multiple detectors should overlap in their fringe zone. Ensure the horizontal installation of the detector.
GB
M-height radial (r)
2,0m 56m² | 16,0m ± 1,5m x 3,5m tangential (t)
56m² | 16,0m ± 1,5m x 3,5m
2,5m 72m² | 18,0m ± 1,5m x 4,0m 88m² | 22,0m ± 1,5m x 4,0m
3,0m
3,5m
4,0m
90m² | 20,0m ± 1,5m x 4,5m 135m² | 30,0m ± 1,5m x 4,5m
100m² | 20,0m ± 1,5m x 5,0m 150m² | 30,0m ± 1,5m x 5,0m
100m² | 20,0m ± 2,0m x 5,0m 150m² | 30,0m ± 2,0m x 5,0m
4,5m
5,0m
6,0m
100m² | 20,0m ± 2,0m x 5,0m 150m² | 30,0m ± 2,0m x 5,0m
100m² | 20,0m ± 2,5m x 5,0m 150m² | 30,0m ± 2,5m x 5,0m
100m² | 20,0m ± 2,5m x 5,0m 150m² | 30,0m ± 2,5m x 5,0m
45
Detection range (mounting height 3,0m)
1
0
3
2
Lux
15m 12 10 8 6 4 2 0 2 4 6 8 10 12 15
0
1
2
1
2 r t
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Please note: because of the virtually horizontal detection of compact passage to both directions, the detection range of tangential (t) movements of persons is different to the range of radial (r) movements towards the detector.
3.2 Light measurement
The detector measures artificial light and daylight reflected directly beneath the detector (beam width approx. ± 30°). The mounting location is used as the reference for the lighting levels.
46
With indirect lighting, the artificial light at the detector’s mounting location should not exceed 2000 Lux (Brightness value > 2000 Lux).
GB
3.3 Connection
A concealed housing should be used for flush-mounted fitting of the com pact passage 24V. A surface frame is available for surface mounting.
24V =
+ compact power 24V
A1 A2 B1 B2
See the technical data
47
4. Start-up
The detectors are supplied ready for operation with a factory setting of recommended standard values. The SendoPro 868-A management remote control for starting-up the system is optionally available. With the remote control all potentiometer values can be set from a distance.
4.1 Settings for switching contact A «Light»
Potentiometer
Brightness threshold “LUX” Scale
● Transfer zones (no working area) approx. 2
● Bright transfer zones approx. 3
● Deactivation of brightness measurement “on”
Depending on the installation location, natural light intensity, furniture, reflection characteristics of the room and the furniture it may be necessary to correct the settings by 1-2 steps on the scale.
For ease of setting up, we recommend the management remote control Sendo-
Pro 868-A.
48
Switch-off delay time
● Transfer zones approx. 5min.
● In the range between 2 - 15min the switch-off delay varies according to its self-learning behavior. The set values <2min or >15min remain fixed.
● «Pulse»: staircase lighting timer control (0.5sec. “on” / 10sec. “off”)
GB
DIP switch
Light measurement: adaptive or fixed hysteresis
● auto adaptive mode.
● fix overridden by a superordinate logic, the adaptive mode can be deactivated.
auto
0-10V lin
fix
0-10V log
49
4.2 Settings for switching output B «Presence»
Switch-off delay time for presence
● The pre-set values remain unchanged (no self-learning effect).
Switch-on delay time for presence
● In case of presence, the contact does not close before the set switch-on delay has elapsed.
● 0 = Contact closes immediately in case of presence.
● Room surveillance function; the contact closes only in case of distinct movements (effective protection against false alarms).
50
4.3 Behaviour on switching on
Whenever the sensor module is plugged onto the power module or the unit is energised, the detector goes through tree phases which are indicated by an LED.
GB
1. Start-up phase (30sec)
● LED flashes every second, both contacts are closed
(light and presence on)
● In case of absence, both contacts open after 30sec.
2. Service phase (10min)
● The “Light” contact reacts instantaneously on brightness in order to check the brightness threshold.
● If the brightness is insufficient the lighting is switched on (LED on),and if the brightness is sufficient the lighting is switched off (LED off).
3. Operation
● The detector is ready for operation (LED off).
51
5. Parallel circuit operation
● The outputs of a number of detectors can be connected in parallel circuit operation. This enables coverage of large and irregularly shaped rooms such as corridors, underground parkings e.g.
● The total permissible load does not increase.
● Presence detection and brightness measurement by all detectors together.
● The brightness threshold value and switch-off delay time must be adjusted individually for each detector.
24V =
+ compact power 24V
A1 A2 B1 B2
+ compact power 24V
A1 A2 B1 B2
See the technical data
52
6. Test Operation
The test mode serves to check the presence detection and the wiring.
6.1 Setting the test mode with DIP-Switch
● Set DIP switch to «Test».
1. Start-up phase (30sec)
● Both contacts are closed for 30sec. (LED 20s «on», 10s «off» )
2. Test mode
● In case of movement (LED on), both contacts close.
● In case of absence (LED off), both contacts open after 10sec.
● NOTE: no brightness measurement.
● The detector remains permanently in the test mode.
6.2 Setting the test mode with SendoPro 868-A
● While setting the test mode with the management remote control SendoPro 868-A, the detector jumps the start-up phase and changes directly into the test mode.
● Test mode ceases automatically after 10 minutes. The detector performs a reset (see section 4.3).
GB
53
7. Technical specifications
Sensor module
Detection range:
Recommended mounting height (Mh)
Maximum range
Mixed light control
Light measurement deactivated
Switch off delay for light
Short pulse
Switch off delay for presence
Switch on delay for presence
Room surveillance
Power module
Nominal voltage compact passage 24V horizontal 360°
Relay output A1, A2 for „light“
Type of contact potential-free micro-contact
Switching capacity: minimal
maximal
2,0 - 3,5m / max. 6m
30 x 5 m tangential,
20 x 5 m radial ca. 10 - 1500Lux
„on“
10sec. - 20min.
0.5sec. „on“/ 10sec. „off“
10sec. - 120min.
0sec. - 10min.
compact power 24V
24V AC/DC ± 20%
Relais, potential free
24V @ AC/DC ±20%
1V / 1mA *)
50W / 460VA
54
Relay output B1, B2 for „presence“
Type of contact potential-free micro-contact
Switching capacity:
Depth
Diameter
Mounting plate
Screw terminals
Size of concealed housing
(for flush-mounting)
Ambient temperature
Degree of protection
Article numbers compact passage 24V
Surface frame for compact
Management remote control SendoPro 868-A
Relay potential-free
24V @ 2Aµ, 230V~2Aµ
50 W (24 V AC/DC), 460 VA
(230 V AC), µ, min. 1 V/1 mA
40mm
48mm
70 x 70mm max. 2x 2.5mm2
Dim. 1, (NIS,PMI)
0° - 50°C
IP 20 (IP 40 installed)
201 4 090
907 0 514
907 0 675
GB
*) A load of more than 60V or 100mA on the switching contact (max. 1.5W) changes its characteristics permanently; the minimum load specification of 1V/1mA can no longer be guaranteed.
55
8. Warranty declaration
Theben HTS presence detectors are manufactured and quality-tested with the utmost care using state-of-the-art technologies. Theben HTS therefore guarantees perfect function, provided the detectors are used as intended. However, should a defect occur, Theben HTS offers the following warranty within the scope of its General Terms and Conditions of Business:
Please bear in mind the following points:
● The warranty period is 24 months, commencing from the manufacturing date.
● The warranty becomes null and void if you or third parties undertake alterations to the units.
● If the presence detector is connected to a software-controlled system, the warranty for this connection is only valid provided the stated interface specification is adhered to.
We undertake to repair or replace as quickly as possible all supplied components which have become defective or unusable as a result of demonstrably bad material, faulty design or defective workmanship up to the expiry of the warranty period.
Returns
In the event of a warranty claim please send the unit together with the delivery note and a brief description of the fault to the dealer concerned.
Industrial property rights
The concept including hardware and software of these units is protected by copyright.
56
9. Troubleshooting
Fault
Lighting does not switch on or switches off in case of presence and darkness
With persons present, the lighting is on although the brightness is sufficient
Lighting does not switch off or switches on spontaneously in case of absence
Cause
Lux value setting is too low; Lighting was switched off manually with clic; Person is outside the detection range; Detection is disturbed by obstacles;
Set switch-off delay setting is too short
Lux value setting is too high; The lighting has been switched on manually with clic recently (wait for 30 min); Detector is in test mode
Wait until the switch-off delay time has elapsed
(self-learning effect); Disturbing heat sources within the detection range (heaters, incandescent lamp/ halogen lamp, moving objects (e.g. curtains due to open windows)
Lighting keeps switching on and off during the service phase
Too much artificial light is falling on the detector, increase lux value. Set DIP switch to „fix“ or reposi tion the detector.
Error blinking (4x per second) Failure during self test;
Device not working!
-
GB
CE Declaration of Conformity
This device complies with the protection regulations of the EMC directives
2004/108/EC and of the Low Voltage directive 2006/95/EC.
57
Dimensions compact passage 24V
26,5 44
48
76
∅ 66
63
Subject to change without prior notice. Errors and omissions excepted.
58
Theben AG
Hohenbergstrasse 32, DE-72401 Haigerloch
Tel. +49 (0) 74 74 692 - 0
Fax +49 (0) 74 74 692 - 150
Hotline
Tel. +49 (0) 74 74 692 - 369
Fax +49 (0) 74 74 692 - 207 [email protected]
Switzerland
Theben HTS AG
Im Langhag 7b, CH - 8307 Effretikon
Tel. +41 (0)52 355 17 00
Fax +41 (0)52 355 17 01 www.theben-hts.ch
Die Kontaktadressen für weitere Länder finden Sie auf www.theben.de
Veuillez compulser les adresses pour des pays supplémentaires sur www.theben.de
Please find the contact addresses for additional countries on www.theben.de
Las direcciones de contacto de otros países las encontrará en www.theben.de
Gli indirizzi per ulteriori paesi sono disponibili su www.theben.de
De contactadressen voor andere landen vindt u op www.theben.de
59
GB
advertisement
Related manuals
advertisement