Aztech HL129EP HomePlug User manual
Add to My manuals2 Pages
Aztech HL129EP is a HomePlug AV2 device that uses your home's electrical wiring to create a high-speed network. It's easy to set up - just plug it into a power outlet and connect it to your modem with an Ethernet cable. You can then connect other devices, like computers,ゲーム機, or printers, to the HL129EP using either Ethernet cables or Wi-Fi. The HL129EP also has two extra power outlets, so you can plug in other devices without having to use a power strip.
advertisement
MODEL
HL129EP
DEVICES ARE PLUG
AND PLAY READY.
A
Package Contents
HomePlug AV2 devices are preconfigured with a common Private Network Name. Adding new HomePlug AV2 devices to an existing network with the default Private Network Name is as easy as plugging the device into the power outlet. If you wish to have a unique
Private Network Name, simply follow the instructions below. This Easy Start Guide, the User Manual, and the HomePlug AV Utility software is included in the Resource CD and is also downloadable on our Aztech Support Website (www.aztech.com/support).
C
Setting up your HomePlug AV Network
The following items below are included in your HL129EP package.
B
HL129EP Ethernet
Cable
Device Overview
Resource CD Easy Start
Guide
NOTE : You may use this AC Passthrough as an extra power outlet.
The HL129EP is also available in a
DEU Plug variant.
BOTTOM VIEW
Ethernet
Port 1 & 2
Reset
Button
Power LED
Powerline
Activity LED
Ethernet
Activity LED 1
Ethernet
Activity LED 2
Simple
Connect
Button
2
STEP 1 :
In Room A, plug in your HomePlug AV2 device into the power outlet and connect it to the modem router using an Ethernet cable.
NOTE: Ensure that your modem router’s internet connection is UP to allow access to the internet.
STEP 2 :
In Room B plug in your other HomePlug AV/HomePlug AV2 device into the power outlet and connect it to your computer’s Ethernet port using an Ethernet cable.
STEP 3 :
Confirm that a connection has established on both HomePlug AV/
HomePlug AV2 devices. All three LEDs (Power , Powerline , and the corresponding Ethernet LED ) must be ON. Your Homeplug AV
Network is now ready to use and can now access Internet.
D
Setup for an Existing Network Connection
If in case you have changed the Private Network Name of your existing network, you may use the Simple Connect Button of your
HL129EP and the other devices as indicated below:
Step 1
HomePlug X
(Your new HomePlug AV2)
HomePlug Y
(A HomePlug that belongs to the existing network)
Step 2
HomePlug X
(Your new HomePlug AV2)
1
Press the Simple Connect button of your HomePlug
X for 10 SECONDS.
After you release the button, the
Power and the Ethernet LED will turn OFF and turn ON.
HomePlug Y
(A HomePlug that belongs to the existing network)
MODEL
HL129EP
Press the Simple Connect Button of HomePlug AV Y for
TWO SECONDS. The Power LED will continuously blink.
If the Power LED did not blink, press the Simple Connect button again for two seconds.
2
Step 3
HomePlug X
(Your new HomePlug AV2)
Step 4
HomePlug X
(Your new HomePlug AV2)
HomePlug Y
(A HomePlug that belongs to the existing network)
3 Within two minutes, press the simple connect button of
HomePlug X for TWO SECONDS .
HomePlug Y
(A HomePlug that belongs to the existing network)
4
To confirm if the connection has established, check the LEDs. The Power LEDs and the Powerline Activity LEDs on all HomePlugs would be ON.
Press for 3 SECONDS to perform factory defaul reset.
NOTES:
• When joining an existing network, you only have to pair it to one HomePlug AV that belongs to the existing network.
• The Ethernet Activity LED will only be lit if it is connected to an Ethernet device (e.g. computer, laptop, etc) through an Ethernet cable.
• To perform RESET to factory defaults, press the reset button for 3 SECONDS.
advertisement
Related manuals
advertisement