ASSEMBLY INSTRUCTIONS

Blower Assembly

THE BLOWER ASSEMBLY MUST BE DISCONNECTED FROM THE SOURCE OF ELECTRICAL SUPPLY BEFORE

ATTEMPTING THE INSTALLATION.

THE BLOWER ASSEMBLY IS INTENDED FOR USE ONLY WITH A STOVE THAT IS MARKED TO INDICATE SUCH USE.

DO NOT ROUTE THE SUPPLY CORD NEAR OR ACROSS HOT SURFACES!

Step 1.

Fix the assembly to the back of the stove with the four screws provided.

Pedestal Trim Assembly

Assemble trim pieces as shown with the screws provided in the parts bag. Washers may not be necessary.

Ash Pan Assembly

Remove ash pan from firebox. Under the firebox, there are two brackets; Slide the ash pan into these brackets.

After trim assembly, attach to the pedestal base at the location shown using the screws provided.

6 Ussc

INSTALLATION

SAFETY NOTICE

• IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE FIRE MAY RESULT. TO

REDUCE THE RISK OF FIRE, FOLLOW THE INSTALLATION INSTRUCTIONS.

• CONSULT YOUR MUNICIPAL BUILDING DEPARTMENT OR FIRE OFFICIALS ABOUT

PERMITS, RESTRICTIONS AND INSTALLATIONS REQUIREMENTS IN YOUR AREA.

• USE SMOKE DETECTORS IN THE ROOM WHERE YOUR STOVE IS INSTALLED.

• KEEP FURNITURE AND DRAPES WELL AWAY FROM THE STOVE.

• NEVER USE GASOLINE, GASOLINE-TYPE LANTERN FUEL, KEROSENE, CHARCOAL

LIGHTER FLUID, OR SIMILAR LIQUIDS TO START OR “FRESHEN UP” A FIRE IN THIS

HEATER. KEEP ALL SUCH LIQUIDS WELL AWAY FROM THE HEATER WHILE IT IS IN

USE.

• IN THE EVENT OF A CHIMNEY FIRE, PUSH THE AIR CONTROL FULL CLOSED TO

DEPRIVE THE FIRE OF OXYGEN. CALL THE FIRE DEPARTMENT.

• DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.

• A SOURCE OF FRESH AIR INTO THE ROOM OR SPACE HEATED SHALL BE PROVIDED

WHEN REQUIRED.

POSITIONING THE STOVE

It is very important to position the wood stove as close as possible to the chimney, and in an area that will favor the most efficient heat distribution possible throughout the house. The stove must therefore be installed in the room where the most time is spent, and in the most spacious room possible. Recall that wood stoves produce radiating heat, the heat we feel when we are close to a wood stove. A wood stove also functions by convection, that is through the displacement of hot air accelerated upwards and its replacement with cooler air. If necessary, the hot air distribution from the stove may be facilitated by the installation of a blower.

The wood stove must not be hooked up to a hot air distribution system since an excessive accumulation of heat may occur.

A wood stove must never be installed in a hallway or near a staircase, since it may block the way in case of fire or fail to respect required clearances.

Ussc 7

FLOOR PROTECTOR

Your wood stove should be placed on a 1 inch, non-combustible surface with a k factor of 0.84. For multiple layers, add R-values of each layer to determine the overall R-value. The R value for the required board is 1.2. If there is a horizontal section of chimney connector, the floor protector should go under it and 2 inches beyond each side

Convert specification to R-value: k-factor is given with a required thickness (T) in inches: R=1/k x T

C-factor is given: R=1/C

Example: factor

If the floor protector is 4” brick with a C-factor of 1.25 over 1/8” mineral board with a “k” of 0.29 the total R-value of the system is:

4” brick C=1.25, R=1/1.25=0.8

1/8” mineral board K=0.29, R=1/0.29 x 0.125=0.431

Total R = Rbrick + Rmineral = 0.8 + 0.431 = 1.231

Total R is greater than 1.2, the system is acceptable.

The floor protector should exceed the stove as follows:

Model

2000

2500

Front

25”

(635mm)

26”

(660mm)

Sides

8”

(203mm)

8”

(203mm)

Rear

¶ 6”

(152mm)

¶ 6”

(152mm)

¶ - Canadian installations require 8” (203mm)

8 Ussc

CLEARANCES TO COMBUSTIBLES

It is of utmost importance that the clearances to combustible materials be strictly adhered to during installation of the stove. Refer to the tables below :

Model A

2000 20(14)

(508mm(356mm))

2500 12

(305mm)

Single Wall Pipe (Double Wall Pipe)

B

22(20)

(559mm(508mm))

C

22.5(16.5)

(572mm(419mm))

D

32(30)

(813mm(762mm))

E

12(11)

(305mm(279mm))

20

(508mm)

16

(406mm)

30

(762mm)

10.5

(267mm)

F

22(21)

(559mm(533mm))

20

(508mm)

• Floor to ceiling height must be at least 7’ (2.13m) in all cases.

• Do not place any combustible material within 4’ (1.2m) of the front of the unit.

• The clearance between the flue pipe and a wall are valid only for vertical walls and for vertical flue pipe.

• The chimney connector must not pass through an attic or roof space, closet or similar concealed space, a floor, or a ceiling.

• For Canadian installations, where passage through a wall, or partition of combustible construction is desired, the installation must conform to CAN/CSA-B365.

• A flue pipe crossing a combustible wall must have a minimum clearance of 18” (457.2mm).

• To reduce flue clearances from combustible materials, contact your local safety department.

Ussc 9

CHIMNEY CONNECTOR (STOVE PIPE)

Your chimney connector and chimney must have the same diameter as the stove outlet (6”). If this is not the case, we recommend you contact your dealer in order to insure there will be no problem with the draft.

The stove pipe must be made of aluminized or cold roll steel with a minimum thickness of 0.021” or

0.53 mm. It is strictly forbidden to use galvanized steel.

Your smoke pipe should be assembled in such a way that the male section (crimped end) of the pipe faces down. Attach each of the sections to one another with three equidistant metal screws.

The pipe must be short and straight. All sections installed horizontally must slope at least 1/4 inch per foot, with the upper end of the section toward the chimney. Any installation with a horizontal run of chimney pipe must conform to NFPA 211. You may contact NFPA (National Fire Protection

Association) and request the latest edition of the NFPA Standard 211 .

To insure a good draft, the total length of the coupling pipe should never exceed 8’ to 10’ (2.4m to 3.04 m). (Except for cases of vertical installation, cathedral-roof style where the smoke exhaust system can be much longer and connected without problem to the chimney at the ceiling of the room).

There should never be more than two 90 degrees elbows in the smoke exhaust system.

Installation of a “barometric draft stabilizer” (fireplace register) on a smoke exhaust system is prohibited.

Furthermore, installation of a draft damper is not recommended. Indeed, with a controlled combustion wood stove, the draft is regulated upon intake of the combustion air in the stove and not at the exhaust.

10 Ussc

CHIMNEY

Your wood stove may be hooked up with a 6” factory built or masonry chimney. If you are using a factory built chimney, it must comply with UL 103 or CSA-B365 standard; therefore it must be a Type HT

(2100°F). It is extremely important that it be installed according to the manufacturer’s specifications.

If you are using a masonry chimney, it is important that it be built in compliance with the specifications of the National Building Code. It must be lined with fire clay bricks, metal or clay tiles sealed together with fire cement. (Round flues are the most efficient).

The interior diameter of the chimney flue must be identical to the stove smoke exhaust. A flue which is too small may cause draft problems, while a large flue favours rapid cooling of the gas, and hence the build-up of creosote and the risk of chimney fires. Note that it is the chimney and not the stove which creates the draft effect; your stove’s performance is directly dependent on an adequate draft from your chimney.

The following recommendations may be useful for the installation of your chimney:

1. DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

2. It must rise above the roof at least 3’ (0.9m) from the uppermost point of contact.

3. The chimney must exceed any part of the building or other obstruction within a 10’ (3.04m) distance by a height of 2’ (0.6m).

4. Installation of an interior chimney is always preferable to an exterior chimney. Indeed, the interior chimney will, by definition, be hotter than an exterior chimney, being heated up by the ambient air in the house. Therefore the gas which circulates will cool more slowly, thus reducing the build-up of creosote and the risk of chimney fires.

5. The draft caused by the tendency for hot air to rise will be increased with an interior chim ney.

6. Using a fire screen at the extremity of the chimney requires regular inspection in order to insure that it is not obstructed thus blocking the draft, and it should be cleaned when used regularly.

Ussc 11

FACTORY BUILT CHIMNEY :

When a metal prefabricated chimney is used, the manufacturer’s installation instructions must be followed. You must also purchase (from the same manufacturer) and install the ceiling support package or wall pass-through and “T” section package, firestops (where needed), insulation shield, roof flashing, chimney cap, etc. Maintain proper clearance to the structure as recommended by the manufacturer. The chimney must be the required height above the roof or other obstructions for safety and proper draft operation.

12 Ussc

MASONRY CHIMNEY :

Ensure that a masonry chimney meets the minimum standards of the National Fire Protection Association (NFPA) by having it inspected by a professional. Make sure there are no cracks, loose mortar or other signs of deterioration and blockage. Have the chimney cleaned before the stove is installed and operated. When connecting the stove through a combustible wall to a masonry chimney, special methods are needed.

Ussc 13

Combustible Wall Chimney Connector Pass-Throughs

Method A.

12” (304.8 mm) Clearance to Combustible Wall Member: Using a minimum thickness 3.5” (89 mm) brick and a 5/8”

(15.9 mm) minimum wall thickness clay liner, construct a wall passthrough. The clay liner must conform to ASTM C315 (Standard

Specification for Clay Fire Linings) or its equivalent. Keep a minimum of 12” (304.8 mm) of brick masonry between the clay liner and wall combustibles. The clay liner shall run from the brick masonry outer surface to the inner surface of the chimney flue liner but not past the inner surface. Firmly grout or cement the clay liner in place to the chimney flue liner.

Method B. 9” (228.6 mm) Clearance to Combustible Wall Member:

Using a 6” (152.4 mm) inside diameter, listed, factory-built Solid-

Pak chimney section with insulation of 1” (25.4 mm) or more, build a wall pass-through with a minimum 9” (228.6 mm) air space between the outer wall of the chimney length and wall combustibles.

Use sheet metal supports fastened securely to wall surfaces on all sides, to maintain the 9” (228.6 mm) air space. When fastening supports to chimney length, do not penetrate the chimney liner (the inside wall of the Solid-Pak chimney). The inner end of the Solid-

Pak chimney section shall be flush with the inside of the masonry chimney flue, and sealed with a non-water soluble refractory cement. Use this cement to also seal to the brick masonry penetration.

Method C.

6” (152.4 mm) Clearance to Combustible Wall Member:

Starting with a minimum 24 gage (.024” [.61 mm]) 6” (152.4 mm) metal chimney connector, and a minimum 24 gage ventilated wall thimble which has two air channels of 1” (25.4 mm) each, construct a wall pass-through. There shall be a minimum 6” (152.4) mm separation area containing fiberglass insulation, from the outer surface of the wall thimble to wall combustibles. Support the wall thimble, and cover its opening with a 24-gage minimum sheet metal support. Maintain the 6” (152.4 mm) space. There should also be a support sized to fit and hold the metal chimney connector. See that the supports are fastened securely to wall surfaces on all sides.

Make sure fasteners used to secure the metal chimney connector do not penetrate chimney flue liner.

Method D. 2” (50.8 mm) Clearance to Combustible Wall Member: Start with a solid-pak listed factory built chimney section at least 12” (304 mm) long, with insulation of 1” (25.4 mm) or more, and an inside diameter of 8” (2 inches [51 mm] larger than the 6”

[152.4 mm] chimney connector). Use this as a pass-through for a minimum 24-gauge single wall steel chimney connector. Keep solid-pak section concentric with and spaced 1” (25.4 mm) off the chimney connector by way of sheet metal support plates at both ends of chimney section. Cover opening with and support chimney section on both sides with 24 gage minimum sheet metal supports.

See that the supports are fastened securely to wall surfaces on all sides. Make sure fasteners used to secure chimney flue line .

NOTES:

1. Connectors to a masonry chimney, excepting method B, shall extend in one continuous section through the wall pass-through system and the chimney wall, to but not past the inner flue liner face.

2. A chimney connector shall not pass through an attic or roof space, closet or similar concealed space, or a floor, or ceiling.

14 Ussc

OUTSIDE COMBUSTION AIR

Your wood stove is approved to be installed with an outside air intake which is necessary for a mobile home. This type of installation is also required in air tight houses and houses with negative pressure problems. You can purchase this option through your heater dealer. Make sure to specify the part number mentioned in this booklet. Installation instructions are supplied with the air intake kit.

Outside combustion air may be required if :

1. Your stove does not draw steadily, smoke rollout occurs, wood burns poorly, or back-drafts occur whether or not there is combustion present.

2. Existing fuel-fired equipment in the house, such as fireplaces or other heating appliances, smell, do not operate properly, suffer smoke roll-out when opened, or back-drafts occur whether or not there is combustion present.

3. Opening a window slightly on a calm (windless) day alleviates any of the above symptoms.

4. The house is equipped with a well-sealed vapor barrier and tight fitting windows and/or has any powered devices that exhaust house air.

5. There is excessive condensation on windows in the winter.

6. A ventilation system is installed in the house.

For use in MOBILE HOMES (U. S. installations ONLY):

• WARNING! DO NOT INSTALL IN SLEEPING ROOM.

• CAUTION! THE STRUCTURAL INTEGRITY OF THE MOBILE HOME FLOOR, WALL, AND

CEILING/ROOF MUST BE MAINTAINED.

• INSTALL IN ACCORDANCE WITH 24 CFR, PART 3280 (HUD).

• USE A FACTORY BUILT CHIMNEY THAT COMPLIES WITH UL 103 STANDARDS;

THEREFORE IT MUST BE A TYPE HT (2100°F).

• USE A SPARK ARRESTER.

• THE STOVE MUST BE ATTACHED TO THE STRUCTURE OF THE MOBILE HOME. USE

THE FOUR(4) HOLES IN THE BOTTOM FLANGES OF THE HEATER’S PEDESTAL TO

SECURE THE UNIT TO THE FLOOR. THEN INTALL/RE-INSTALL THE TRIM.

NONCOMBUSTIBLE FLOORING

Illustration: Securing heater to the Floor.

Ussc 15

WOODSTOVE UTILIZATION

Your heating unit was designed to burn wood only; no other materials should be burned. Waste and other flammable materials should not be burned in your stove. Any type of wood may be used in your stove, but specific varieties have better energy yields than others. Please consult the following table in order to make the best possible choice.

TYPE

Hickory

WEIGHT

(LBS. CU. FT.,

DRY)

63

PER CORD EFFICIENCY

RANKING

4500 1.0

SPLITS

Well

MILLIONS

BTU’s/CORD

31.5

White Oak

Red Oak

Beech

Sugar Maple

Black Oak

Ash

Yellow Birch

Red Maple

Paper Birch

Elm/Sycamore

Red Spruce

43

42

40

38

37

34

29

48

46

45

44

3700

3600

3400

3200

3100

2900

1800

4100

3900

3800

3700

.4

.3

.3

.6

.5

.2

.1

.7

.6

.9

.8

Fair

Fair

Hard

Fair

Fair

Well

Hard

Fair

Easy

Very Difficult

Easy

25.6

25.0

23.8

22.6

22.1

20.1

16.1

28.6

27.4

26.8

26.2

It is EXTREMELY IMPORTANT that you use DRY WOOD only in your wood stove.

The wood should have dried for 9 to 15 months, such that the humidity content (in weight) is reduced below 20% of the weight of the log. It is very important to keep in mind that even if the wood has been cut for one, two or even more years, it is not necessarily dry, if it has been stored in poor conditions. Under extreme conditions it may rot instead of drying. This point cannot be over stressed; the vast majority of the problems related to the operation of a wood stove is caused by the fact that the wood used was too damp or had dried in poor conditions. These problems can be:

- ignition problems

- creosote build-up causing chimney fires

- low energy yield

- blackened windows

- incomplete log combustion

Smaller pieces of wood will dry faster. All logs exceeding 6” in diameter should be split. The wood should not be stored directly on the ground. Air should circulate through the cord. A 24” to 48” air space should be left between each row of logs, which should be placed in the sunniest location possible. The upper layer of wood should be protected from the elements but not the sides.

TESTING YOUR WOOD

When the stove is thoroughly warmed, place one piece of split wood (about five inches in diameter) parallel to the door on the bed of red embers.

Keep the air control full open by pulling on it and close the door. If ignition of the piece is accomplished within 90 seconds from the time if was placed in the stove, your wood is correctly dried. If ignition takes longer, your wood is damp.

If your wood hisses and water or vapor escapes at the ends of the piece, your wood is soaked or freshly cut. Do not use this wood in your stove. Large amounts of creosote could be deposited in your chimney, creating potential conditions for a chimney fire.

16 Ussc

THE FIRST FIRES

The fresh paint on your stove needs to be cured to preserve its quality. Once the fuel charge is properly ignited, only burn small fires in your stove for the first four hours of operation. Never open the air control more than necessary to achieve a medium burn rate.

Make sure that there’s enough air circulation while curing the stove. The odors could be smelled during the 3 or 4 first fires. Never start your stove outside. You will not be able to see if you are over heating.

IGNITION

After making sure that the stove air intake controls are fully open (completely pull-out towards you), place several rumpled sheets of paper in the centre of the combustion chamber. Place 8 to 10 pieces of small dry kindling wood over the paper in the form of a tent. You may also place a few pieces of heating wood, but choose the smaller ones. No chemical product should be used to light the fire.

Before igniting the paper and kindling wood, it is recommended that you warm up the chimney. This is done in order to avoid back draft problems often due to negative pressure in the house. If such is the case, open a window slightly near the stove and twist together a few sheets of newspaper into a torch. Light up this paper torch and hold it as close as possible to the mouth of the pipe inside the combustion chamber to warm up the chimney. Once the updraft movement is initiated, you are ready to ignite the stove by lighting the paper and kindling wood inside the combustion chamber.

When you have achieved a good bed of hot embers, we recommend the following burn procedures:

2000

Primary Air Settings

(Slide Damper is located in center of stove under hearth plate)

(Damper Adjustment: Pulling out on damper increases air)

Burn Rate

Low

Medium - Low

Medium - High

High

Burn Rate

Low

Medium - Low

Medium - High

High

Adjust Damper from fully closed

1/4” (6.3mm)

3/8” (9.5mm)

1/2” (12.7mm) approx. 3” (76mm)

Adjust Damper from fully closed

1/32” (1mm)

2500

1/16” (1.5mm)

5/16” (8mm) approx. 3” (76mm)

Electric Blower Speed Setting (Variable)

(Blower is on High when turned “ON”, Rotate clockwise until stop for “LOW”.)

Burn Time

@ 30 minutes

@ 30 minutes

Blower Speed

Low

Low

@ 30 minutes all minutes

Low

High

Burn Time

@ 30 minutes

@ 30 minutes

@ 30 minutes all minutes

Blower Speed

Low

Low

Low

High

CAUTION: Never alter the damper slide or the adjustment range to increase firing for any reason. Doing so could result in heater damage and will void your warranty.

HEATING

Controlled combustion is the most efficient technique for wood heating because it enables you to select the type of combustion you want for each given situation. The wood will burn slowly if the wood stove air intake control is adjusted to reduce the oxygen supply in the combustion chamber to a minimum. On the other hand, wood will burn quickly if the air control is adjusted to admit a larger quantity of oxygen in the combustion chamber. The air intake control on your stove is very simple. If you pull on it out completely towards you, it is fully open. If you push on it until it stops the combustion air is reduced to a minimum. Real operating conditions may give very different results than those obtained during testing according to the species of wood used, its moisture content, the size and density of the pieces, the length of the chimney, altitude and outside temperature.

Ussc 17

WARNINGS

• NEVER OVERFIRE YOUR STOVE. IF ANY PART OF THE STOVE STARTS TO GLOW RED,

OVER FIRING IS HAPPENING. READJUST THE AIR INTAKE CONTROL AT A LOWER

SETTING.

• THE INSTALLATION OF A LOG CRADLE or GRATES IS NOT RECOMMENDED IN YOUR

WOOD STOVE. BUILD FIRE DIRECTLY ON FIREBRICK.

• NEVER PUT WOOD ABOVE THE FIREBRICK LINING OF THE FIREBOX.

RELOADING

Once you have obtained a good bed of embers, you should reload the unit. In order to do so, open the air controls to maximum a few seconds prior to opening the stove’s door. Then proceed by opening the door very slowly; open it one or two inches for 5 to 10 seconds, before opening it completely to increase the draft and thus eliminate the smoke which is stagnant in a state of slow combustion in the stove. Then bring the red embers to the front of the stove and reload the unit.

For optimal operation of your wood stove, we recommend you to operate it with a wood load approximately equivalent to the height of fire bricks.

It is important to note that wood combustion consumes ambient oxygen in the room .In the case of negative pressure, it is a good idea to allow fresh air in the room, either by opening a window slightly or by installing a fresh air intake system on an outside wall.

Creosote - Formation and Need for Removal - When wood is burned slowly, it produces tar and other organic vapors, which combine with expelled moisture to form creosote. The creosote vapors condense in the relatively cool chimney flue of a slow-burning fire. As a result, creosote residue accumulates on the flue lining. When ignited this creosote makes an extremely hot fire. The chimney connector and chimney should be inspected at least once every two months during the heating season to determine if a creosote build-up has occurred. If creosote has accumulated (3mm or more), it should be removed to reduce the risk of a chimney fire.

We strongly recommend that you install a magnetic thermometer on your smoke exhaust pipe, approximately 18” above the stove. This thermometer will indicate the temperature of your gas exhaust fumes within the smoke exhaust system. The ideal temperature for these gases is somewhere between 275°F and 500°F. Below these temperatures, the build-up of creosote is promoted. Above

500 degrees, heat is wasted since a too large quantity is lost into the atmosphere.

TO PREVENT CREOSOTE BUILD UP

• Always burn dry wood. This allows clean burns and higher chimney temperatures, therefore less creosote deposit.

• Leave the air control full open for about 5 min. every time you reload the stove to bring it back to proper operating temperatures. The secondary combustion can only take place if the firebox is hot enough.

• Always check for creosote deposit once every two months and have your chimney cleaned at least once a year.

If a chimney or creosote fire occurs, close all dampers immediately. Wait for the fire to go out and the heater to cool, then inspect the chimney for damage. If no damage results, perform a chimney cleaning to ensure there is no more creosote deposits remaining in the chimney.

18 Ussc

ASH DISPOSAL

Ashes should be removed from the stove every few days or when ashes get to 2 to 3 inches deep.

Always empty the stove when it is cold, such as in the morning. Ashes should be placed in a metal container with a tight fitting lid. The closed container of ashes should be placed on a non combustible floor or on the ground, well away from all combustible materials, pending final disposal. If the ashes are disposed of by burial in soil or otherwise locally dispersed, they should be retained in the close container until all cinders have thoroughly cooled. Other waste shall not be placed in this container.

CAUTIONS:

• ASHES COULD CONTAIN HOT EMBERS EVEN AFTER TWO DAYS WITHOUT OPERATING THE

STOVE.

• THE ASH PAN CAN BECOME VERY HOT. WEAR GLOVES TO PREVENT INJURY.

• NEVER BURN THE STOVE WITH THE ASH TRAP OPEN. THIS WOULD RESULT IN OVER FIRING

THE STOVE. DAMAGE TO THE STOVE AND EVEN HOUSE FIRE MAY RESULT.

MAINTENANCE

Your wood stove is a high efficiency stove and therefore requires little maintenance. It is important to perform a visual inspection of the stove every time it is emptied, in order to insure that no parts have been damaged, in which case repairs must be performed immediately. Inspect and clean the chimney and connector pipe periodically for creosote buildup or obstructions.

GLASS

• Inspect and clean the glass regularly in order to detect any cracks. If you spot one, turn the stove off immediately. Do not abuse the glass door by striking or slamming shut. Do not use the stove if the glass is broken.

• If the glass on your stove breaks, replace only with the glass supplied from your heater dealer.

Never substitute other materials for the glass.

• To replace the glass, remove the screws retaining the glass mouldings inside the door. Remove the mouldings and replace the damaged piece with a new one. Perform the procedure backwards after replacing. When replacing the glass, you should change the glass gasket to make sure you keep it sealed.

• Never wash the glass with a product that may scratch. Use a specialized product, available in the stores where wood stoves are sold. The glass should be washed only when cold.

GASKETING

It is recommended that you change the door gasket (which makes your stove door air tight) once a year, in order to insure good control over the combustion, maximum efficiency and security. To change the door gasket, simply remove the damaged one. Carefully clean the available gasket groove, apply a high temperature silicone sold for this purpose, and install the new gasket. You may light up your stove again approximately 24 hours after having completed this operation.

WARNING:

• NEVER OPERATE THE STOVE WITHOUT A GASKET OR WITH A BROKEN ONE. DAMAGE

TO THE STOVE OR EVEN HOUSE FIRE MAY RESULT.

PAINT

Only clean your stove with a dry soft cloth that will not harm the paint finish. If the paint becomes scratched or damaged, it is possible to give your wood stove a brand new look, by repainting it with a 1200° F heat resistant paint. For this purpose, simply scrub the surface to be repainted with fine sand paper, clean it properly, and apply thin coats (2) of paint successively.

Ussc 19

REPAIR PARTS

19

20

21

17

18

37

16

15

2 3 4

5 6 7

12

13

14

27

28

31

36

30

34

Feed Door Assembly

5

32 33

35

6

7

1

29

8

10

24 25

26

3

11

11

10

8 9

1

23 22

4

9

2

20 Ussc

3

4

5

1

2

6

7

8

11

12

13

14

15

19

20

21

16

17

18

22

9

10

Key Part No. Description

69515MB Feed Door Assy.

25080B Feed Door Latch

83508 5/16-18 x 3/4 Hex Head Bolt

83338 5/16-18 Lock Nut

891373 Door Hinge Pad

83045A Washer, 3/8” ID x 7/8” OD

83274 3/8-16 Lock Nut

86643

Tube, Secondary Air (Ø0.16 holes)

2000

2500

86645

Tube, Secondary Air (Ø0.22 holes)

2000

2500

891515 Retainer, Tube (1 per Secondary Tube)

88146

88138

Refractory Insulation

891516 Damper Slide

2000

2500

891517 Hearth Plate

891331 Spring Handle - Small

891514 Shield, Rear

891528 Air Deflector

40292A Flue Collar

88032 Flue Collar Gasket

83432 5/16-18 x 1-1/2 Hex Head Bolt

83045 Washer, 5/16” ID x 3/4” OD

83431 Weld Tab

2000

89066 Firebrick (4.5 x 9 x 1.25)

2500

REPAIR PARTS

Key Part No. Description

2

2

1

1

2

1

1

2

2

1

2

3 - 5

1

1

1

1

1

1

1

1

1.7 Ft

3

3

3

16

18

23

24

25

26

27

28

29

30

31

32

33

34

35

36

N/S u

37

891414 Firebrick (2-1/4 x 9)

24103 Firebrick (4-1/2 x 4-1/2)

891530 Firebrick (4-1/2 x 7-1/2 )

40561 Ash Plug

891777

891788

Pedestal Wrapper

891778

891521

891779

891526

Pedestal Bottom

891523 Pedestal Back

891527 Ash Pan

891137 Handle

40496 Corner Trim

83466 8-32 x 1/4 Self Tapping Screw

891524 Front Pedestal Trim

Right Side Pedestal Trim

891780

891525

Left Side Pedestal Trim

891944 Trim, One Piece

891945 Trim, One Piece

69354 B36 Blower Assembly

N/S = Not Shown u = Used on heaters manufactured in 2011

All components common except where noted.

2000

2500

2000

2500,

2000

2500

2000

2500

2000

2500

1

1

1

1

1

1

1

2

8

1

1

1

1

2

1

1

1

1

1

1

1

Key Part No.

9

10

11

6

7

8

1

2

3

4

5

25491

25692

83506

891135

88066

88087

891131

25464

25465

83202

83278

Description

Feed Door, Painted (40484)

Handle, Painted (40515)

3/8 x 1-1/4 Roll Pin

Spring Handle - LG

Rope Gasket - 5/8”

Glass Gasket - 1/8 thk x 1” wide

Ceramic Glass

Top Glass Retainer

Bottom Glass Retainer

10-24 x 3/8 Pan Head Phillips Screw

Washer - 7/32 ID x 1/2 OD

Qty.

1

1

1

1

4.6 Ft

3.7 Ft

1

1

1

4

4

Key Part No.

Z

N/S

40566

83339

For Models with Legs

Description

Leg, Cast Iron

Bolt, 1/4-20 x 3/4

Qty.

2

8

Ussc 21

NOTES

22 Ussc

NOTES

Ussc 23

HOW TO ORDER REPAIR PARTS

THIS MANUAL WILL HELP YOU OBTAIN EFFICIENT, DEPENDABLE SERVICE

FROM YOUR HEATER, AND ENABLE YOU TO ORDER REPAIR PARTS COR-

RECTLY.

KEEP THIS MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE.

WHEN WRITING, ALWAYS GIVE THE FULL MODEL NUMBER WHICH IS ON

THE NAMEPLATE ATTACHED TO THE HEATER.

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFOR-

MATION AS SHOWN IN THIS LIST:

1. THE PART NUMBER

2. THE PART DESCRIPTION

3. THE MODEL NUMBER: _______________________

4. THE SERIAL NUMBER: _______________________

UNITED STATES STOVE COMPANY

227 INDUSTRIAL PARK ROAD

P.O. BOX 151

SOUTH PITTSBURG, TN 37380

(423) 837-2100

WWW.USSTOVE.COM

24 Ussc