Quadra-Fire 31M-ACC-MBK, 31ST-ACC Owner's Manual

R

3100 WOOD STOVE SERIES

Advanced Combustion Control (ACC)

Owner’s Manual

Installation and Operation

Models:

31M-ACC-MBK

31ST-ACC

Tested and

Listed by

O-T L Portland

Oregon USA

C US

OMNI-Test Laboratories, Inc.

Step Top Uni-Body Model

(Pedestal Model Shown)

Millennium Model

CAUTION

• Important operating a n d m a i n t e n a n c e instructions included.

DO NOT DISCARD THIS MANUAL

• Read, understand and follow these instructions for safe installation and operation.

• Leave this manual with party responsible for use and operation.

DO NOT

DISCARD

WARNING

If the information in these instructions is not followed exactly, a fi re may result causing property damage, personal injury, or death.

• Do not store or use gasoline or other fl ammable vapors and liquids in the vicinity of this or any other appliance.

• Do not overfi re - If heater or chimney connector glows, you are overfi ring. Overfi ring will void your warranty.

• Comply with all minimum clearances to combustibles as specifi ed. Failure to comply may cause house fi re.

Installation and service of this appliance should be performed by qualifi ed personnel. Hearth &

Home Technologies recommends NFI certifi ed professionals, or technicians supervised by an

NFI certifi ed professional.

www.quadrafi re.com

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

• Do not touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as fi replace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other fl ammable materials.

• Keep clothing, furniture, draperies and other fl ammable materials away.

7033-277H

WARNING

Fire Risk.

For use with solid wood fuel only.

Other fuels may overfi re and generate poisonous gases (i.e. carbon monoxide).

September 1, 2010

3100 Wood Stove Series (ACC)

and Welcome to the Quadra-Fire Family

!

Hearth & Home Technologies welcomes you to our tradition of excellence! In choosing a Quadra-Fire appliance, you have our assurance of commitment to quality, durability, and performance.

This commitment begins with our research of the market, including ‘Voice of the Customer’ contacts, ensuring we make products that will satisfy your needs. Our Research and Development facility then employs the world’s most advanced technology to achieve the optimum operation of our stoves, inserts and fi replaces. And yet we are old-fashioned when it comes to craftsmanship. Each unit is meticulously fabricated and surfaces are hand-fi nished for lasting beauty and enjoyment. Our pledge to quality is completed as each model undergoes a quality control inspection.

We wish you and your family many years of enjoyment in the warmth and comfort of your hearth appliance. Thank you for choosing Quadra-Fire.

NOTE: Clearances may only be reduced by means approved by the regulatory authority having jurisdiction

SAMPLE OF SERIAL NUMBER / SAFETY LABEL

LOCATION: BACK OF APPLIANCE

CAUTION

:

HOT WHILE IN OPERATION DO NOT TOUCH, KEEP CHILDREN AND CLOTHING AWAY. CONTACT MAY CAUSE SKIN BURNS. KEEP

FURNISHINGS AND OTHER COMBUSTIBLE MATERIAL FAR AWAY FROM THE APPLIANCE. SEE NAMEPLATE AND INSTRUCTIONS

ATTENTION:

CHAUD LORS DE L'OPÉRATION. NE PAS TOUCHER. GARDEZ LES ENFANTS ET LES VÊTEMENTS LOIN DE L'ESPACE DÉSIGNÉ DE L'INSTALLATION. LE CONTACT PEUT CAUSER DES

BRÛLURES À LA PEAU. GARDEZ LES MEUBLES ET LES MATÉRIAUX COMBUSTIBLES LOIN DE L'ESPACE DÉSIGNÉ DE L'APPAREIL. VOIR L'ÉTIQUETTE ET LES INSTRUCTIONS.

APPAREIL DE CHAUFFAGE DE PIÈCE, DE TYPE DE

LISTED ROOM HEATER, SOLID FUEL TYPE.

ALSO FOR USE IN MOBILE HOMES. (UM) 84 HUD .

"For Use with Solid Wood Fuel Only"

MOBILES. (UM) 84-64 HUD. "Pour Usage Avec Bois Solide

Seulement"

PREVENT HOUSE FIRES

PRÉVENTION DES FEUX DE MAISON

Install and use only in accordance with manufacturer's installation and operating

Installez et utilisez en accord avec les instructions d'installation et instructions. Contact local building or fire officials d'opération du fabricant. Contactez le bureau de la construction ou about restrictions and installation inspections in le bureau des incendies au sujet des restrictions et des inspections your area. Do not obstruct the space beneath heater.

WARNING - For Mobile Homes : Do not install in a sleeping room. An outside combustion air inlet must be provided and unrestricted while unit is in use. The structural integrity of the mobile home d'installation dans votre voisinage. Ne pas obstruez l'espace en dessous de l'appareil.

AVIS - Pour Les Maisons Mobiles: Ne pas installer dans une chambre à coucher. Un tuyau extérieur de combustion d'air doit

être installé et ne doit pas être obstrué lorsque l'appareil est en floor, ceiling and walls must be maintained. The stove needs to be properly grounded to the frame usage. La structure intégrale du plancher, du plafond et des murs de la maison mobile doit être maintenue intacte. L'appareil de of the mobile home. Components required for chauffage doit être fixé à la charpente de la maison mobile. Les composants requis pour l'installation des maisons mobiles: mobile home installation: Outside Air Kit, Part

Number OAK-ACC.

Refer to manufacturer's instructions chimney through a combustible wall or ceiling and maximum offsets.

and local codes for precautions required for passing

Assemblage d'air extérieur, Numéro de Pièce OAK-ACC.

Référez vous aux instructions du fabricant et des codes locaux pour les précautions requises pour passer une cheminée à travers un mur ou un plafond combustibles, et les compensations maximums.

Inspect and clean chimney frequently - Under

Certain Conditions of Use, Creosote Buildup May

Occur Rapidly.

Do not connect this unit to a chimney serving another appliance.

Optional Components: Optional Blower, Part

BK-ACC.

Electrical Rating: 115 VAC, 1.2 Amps, 60 Hz.

Route power cord away from unit. Do not route

Inspectez et nettoyez la cheminée fréquemment. Sous certaines conditions, il se peut que la créosote s'accumule rapidement.

Ne pas connecter cet appareil à une cheminée servant un autre appareil.

Composants Optionnels: Ventilateur Optionnel, Pièce BK-ACC.

Puissance Électrique: 115 VAC, 1.2 Amps, 60 Hz.

Éloignez le fil électrique de l'appareil. Ne pas faire passer le fil cord under or in front of appliance.

DANGER: Risk of electrical shock.

Disconnect power supply before servicing.

Replace glass only with 5mm ceramic available from your dealer.

Do not use grate or elevate fire. Build wood fire directly on hearth.

Do not overfire - if heater or chimney connector

électrique au dessus ou en dessous de l'appareil.

DANGER: Il y a risque de décharge électrique

. Déconnectez le fil électrique de la prise de contact avant le service.

Remplacez la vitre seulement avec une vitre céramique de 5 mm disponible chez votre fournisseur.

N'élevez pas le feu. Bâtissez le feu de bois directement sur l'âtre.

Ne pas surchauffer. Si l'appareil de chauffage ou le tuyau de glows, you are overfiring.

Operate only with the fuel loading door closed.

Open only to add fuel to the fire.

FLOOR PROTECTION :

Floor protector for Millennium and Pedestal Step Top Models must be a 3/8 inch min. thickness, non-combustible material or equivalent,

(Step Top Leg Model only must be 1/2 inch [13mm] min thickness, “k” value 0.84, R value 0.59 or non-combustible floor protector 1-1/4 inch

[32mm] thick) extending beneath heater and to front/sides/rear as indicated on the diagram below.

Exception

: Non-combustible floor protections must extend beneath the flue pipe when installed with horizontal venting and extend 2 inches (51mm) beyond each side.

Opérez l'appareil seulement lorsque la porte de chargement est fermée. Ouvrez la porte seulement lorsque vous devez ajouter des cheminée rougissent, vous surchauffez.

combustibles dans le feu.

S

PROTECTION DU PLANCHER:

Le protecteur de plancher doit être (Modèles Millennium et au dessus en escalier socle) d'un minimum de 3/8 inch (9.5 mm) d'épaisseur, de matériel incombustible ou équivalent, (Modèle au dessus en escalier pied d’un minimum de 1/2 inch [13mm] d'épaisseur, “k” =0.84, R value 0.59 au le protecteur de plancher de matériel incombustible 1-1/4 inch

[32mm] d’épaisseur). s'étendant du dessous de l'appareil de chauffage

à l'avant, aux cotés et à l'arrière comme indiqué sur le diagramme suivant. Exception: Les protections incombustibles du plancher doivent s'étendre en dessous du conduit de cheminée lorsqu'installées avec une ventilation à l'horizontale et s'étendre de 2 inches (51mm) de chaque côté.

Tested and

Listed by

O-T L Portland

Oregon USA

R

3100 Wood

SERIAL NO.

/ NUMÉRO DE SÉRIE

007

C US

OMNI-Test Laboratories, Inc.

TESTED TO:/ TESTÉ À:

UL 1482, ULC S627-00

Stove Series ACC

Report / Rapport

#061-S-66-6

SPÉCIFICATIONS DE LA VENTILATION:

VENT SPECIFICATIONS:

MUR SIMPLE: De six (6") (152mm) de diamètre le connecteur de conduit de

SINGLE WALL: Six inch (6") (152mm) diameter, minimum 24 MSG black or blued minimum d'acier noir ou bleu de minimum de 24MSG, avec une cheminée bâtit en steel connector pipe, with a listed factory-built UL103HT* Class "A" chimney, suitable usine UL103HT* de Classe "A", adéquate pour usage avec les combustions solides, for use with solid fuels, or a masonry chimney, and the referenced clearances.

ou une cheminée de briques, avec espaces libres référés.

DOUBLE WALL: Six inch (6") (152mm) diameter, listed double wall air insulated

MUR DOUBLE: De six (6") (152mm) de diamètre, le connecteur du conduit d'air isolé connector pipe with listed factory-built UL103HT* Class "A" chimney, or a masonry pour mur double avec une cheminée bâtit en usine UL103HT* de Classe "A, ou une chimney and the referenced clearances

*In Canada must comply with Standard CAN/ULC-S629-M87 for the 650 degree

MOBILE HOME: Use double wall pipe by Dura-Vent DVL, Selkirk Metalbestos DS or

Security DL double wall connector pipe. Must be equipped with a spark arrestor.

Apply double wall clearances below when installing unit.

NOTE: All "A" , "C" and "F" Dimensions are to inside diameter of the flue collar.

Factory-built chimneys.

MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS:In Inches & (Millimeters)

INSTALLATION: ENTIÈREMENT VERTICALE OU HORIZONTALE AVEC 609mm VERTICAL MINIMUM DU HAUT DU POÊLE

SINGLE WALL PIPE

DOUBLE WALL PIPE

INSTALLATION: 90 ELBOW OFF TOP OF STOVE THROUGH BACKWALL

INSTALLATION: 90 DE COURBURE AU DESSUS DU HAUT DU POÊLE À TRAVERS LE MUR ARRIÈRE

SINGLE WALL PIPE A

A B C D E F G H

15.25 (387) 11.75 (298) 25.5 (648) 16 (406)

10.5 (267) 6.5 (165) M

P

22 (559) 13 (330)

12 (305) 8.5 (216) 22 (559) 13 (330)

L

8 (203)

8 (203)

E

NOTE: Toutes les dimensions "A", "C", et "F" sont à partir du diamètre intérieur de l'entrée du conduit.

17 (432) 48 (1220) 12(305)

17 (432) 48 (1220) 12 (305)

8 (203) 4.5 (114) 17.5 (445) 8.5 (216) 6.5 (165) 15.5 (394) 48 (1220) 9 (229)

(1220mm) with a minimum height of 48 inches (1220mm) to top of unit, and the referenced clearances. cheminée de briques, avec espaces libres alloués.

*Au Canada doit conformer a CAN/ULC-S629-M87 la norme pour 650 degré C cheminée bâtit en usine.

MAISON MOBILE: Utiliser un conduit de mur double par Dura-Vent DVL, Selkirk

Metalbestos DS ou Security DL. Doit être équipé d'un arrêt d'étincelle. Utiliser les espaces libres pour mur double comme mentionné ci-bas.

ESPACES LIBRES MINIMUM DES MATÉRIAUX COMBUSTIBLES:En Pouces & (millimètres)

INSTALLATION: FULL VERTICAL OR HORIZONTAL WITH MINIMUM 2 FT VERTICAL OFF STOVE TOP

6.5 (165) 15.5 (394) 48 (1220) 9 (229)

CONDUIT DU MUR SIMPLE

C ONDUIT DU MUR DOUBLE

CONDUIT DU MUR SIMPLE

CONDUIT DU MUR DOUBLE

INSTALLATION: ALCOVE - Six inch (6") (152mm) diameter listed DOUBLE WALL air insulated connector pipe with UL 103HT listed factory-built Class "A" chimney, or a masonry chimney. (Mobile Home must be equipped with a spark arrestor.) Maximum depth of Alcove shall be no more than 48 inches

BACKWALL/SIDEWALL

MUR ARRIÈRE/MUR DE CÔTÉ

A B

C

D

CORNER INSTALLATION

INSTALLATION DU COIN

INSTALLATION: ALCÔVE

- De six (6") (152mm) de diamètre, le connecteur du conduit d'air isolé pour mur double avec une cheminée bâtit en usine 103HT de Classe "A", ou une cheminée de briques. (Les maisons mobiles doivent être équipées d'un arrêt d'étincelle). La profondeur maximum de l'alcôve ne doit pas être de plus de 48 inches (1220mm) avec une hauteur minimum de 43 inches (1220mm) du haut de l'appareil, et des espaces libres alloués.

E

F

DOUBLE WALL PIPE 11.75 (298) 8.25 (210) 23.5 (597) 14.5 (368) N/A N/A 48 (1220) * CONDUIT DU MUR DOUBLE

E

* SEE PIPE MANUFACTURERS CLEARANCES - NOT TESTED / VOIR LE FABRICANT POUR LES ESPACES LIBRES DES CONDUIT - PAS TESTÉ

F

ALCOVE SIDE VIEW /

VUE DE CÔTÉ DE L'ALCÔVE

ALCOVE TOP VIEW /

VUE DU HAUT DE L'ALCÔVE

H

203mm (8")

203mm

(8")

Millennium

1280mm

(50-3/8") minimum

Fuel loading door

16" from glass

8"

Millennium

& Step Top

39-5/8” minimum

203mm

(8")

G

A

B

C

D

G

90 ELBOW OFF TOP

UP & OUT CEILING CLEARANCE

ESPACE LIBRE DU DESSUS DE

L'APPAREIL AU PLAFOND AVEC 90 DE

COURBURE

USA

457mm (18")

Step Top

1321mm

(52") minimum

STOVE TO CEILING CLEARANCE

ESPACE LIBRE DU POÊLE AU PLAFOND

Millennium & Step Top 31-5/8" Min

CANADA

1040mm (41") minimum

Manufactured by:

Fabriqué par:

1445 N. Highway, Colville, WA 99114 www.quadrafire.com

DO NOT REMOVE THIS LABEL / NE PAS ENLEVER L'ÉTIQUETTE

U.S. ENVIRONMENTAL PROTECTION AGENCY - Certified to comply with July 1990 particulate emission standards.

Made in U.S.A./Fait Aux États-Unis

7033-278

Serial No.

Model

Name

Test Lab &

Report No.

Mfg. Date

R

Page 2 7033-277H September 1, 2010

R


Safety Alert Key:

• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.

• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.

• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• NOTICE: Indicates practices which may cause damage to the fi replace or to property.

TABLE OF CONTENTS

Section 1: Listing and Code Approvals

B. Mobile Home Approved ......................4

D. BTU & Effi ciency Specifi cations ..........4

Section 2: Getting Started

A. Design, Installation & Location

Fire ..........................................5

D. Flue Draft Considerations ...................7

F. Tools and Supplies Needed................7

G. Inspect Appliance & Components.......7

H. Typical Stove System .........................8

Section 3: Dimensions & Clearances

B. Clearances to Combustibles ...............11

Section 4: Installation Consideration

Section 8: Operating Instructions

A. Over-Firing Your Appliance .................25

B. Wood Selection & Storage ..................25

F. Burn Rates & Operating Effi ciency .....27

G. Building A Fire .....................................28

I. Blower Operating Instructions .............30

K. Frequently Asked Questions...............30

Section 9

:

Maintaining & Servicing Appliance

A. Quick Reference Maintenance Guide ........31

A. General Maintenance & Cleaning .......32-33

E. Snap Disc Replacement .....................36

F. Tube Channel Replacement ...............37

Section 10: Troubleshooting ........................

38

Section 11: Reference Material

B. Service Parts & Accessories...............41-45

Section 5: Chimney Requirements

C. Installing Chimney Components .........18

D. Chimney Termination Requirements ..19

Section 6: Mobile Home ...............................

20

Section 7: Appliance Set-Up

A. Pedestal & Ash Removal System

(ARS) Installation ...............................21-22

B. Leg Kit & Ash Removal System

C. Door Handle Assembly .......................24

D. Blower Speed Adjustment ..................24

E. Alternate Floor Protection Calculation 24

September 1, 2010 7033-277H Page 3


1

Listing and Code Approvals

A. Appliance Certifi cation

Model: 3100 Millennium & Step Top Uni-Body

(ACC)

Laboratory: OMNI Test Laboratories, Inc.

Report No & Date: 061-S-66-6

Type:

Standard:

Listed Room Heater, Solid Fuel Type

UL1482 and ULC S627-00 and

(UM) 84-HUD, Mobile Home

Approved.

The Quadra-Fire 3100 Series Wood Stove (ACC) meets the

U.S. Environmental Protection Agency’s 1990 particulate emission standards.

D. BTU & Effi ciency Specifi cations

EPA Certifi ed:

EPA Certifi cation

Number and Date:

Effi ciency:

BTU Output:

Heating Capacity:

Vent Size:

Firebox Size:

Max Wood Length:

Fuel:

Shipping Weight:

1.1 grams per hour

Number: 369

Issued: 2006

90.2%

11,800 to 32,000 up to1,800 sq ft depending on climate zone

6 inches

2 cubic feet

18 inches

Cord Wood

325 lbs

R

B. Mobile Home Approved

This appliance is approved for mobile home installations when not installed in a sleeping room and when an outside combustion air inlet is provided. The structural integrity of the mobile home fl oor, ceiling, and walls must be maintained.

The appliance must be properly grounded to the frame of the mobile home and use only listed double-wall connector pipe. Outside Air Kit, part OAK-ACC must be installed in a mobile home installation

C. Glass Specifi cations

This stove is equipped with 5mm ceramic glass. Replace glass only with 5mm ceramic glass. Please contact your dealer for replacement glass.

NOTE: This installation must conform with local codes. In the absence of local codes you must comply with the UL1482, (UM)

84-HUD and NPFA211 in the U.S.A. and the ULC S627-00 and

CAN/CSA-B365 Installation Codes in Canada.

WARNING

Fire Risk.

Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:

• Installation and use of any damaged appliance.

• Modifi cation of the appliance.

• Installation other than as instructed by Hearth & Home

Technologies.

• Installation and/or use of any component part not approved by Hearth & Home Technologies.

• Operating appliance without fully assembling all components.

• Operating appliance without legs attached (if supplied with unit).

• Do NOT Overfi re - If appliance or chimney connector glows, you are overfi ring.

Any such action that may cause a fi re hazard.

NOTE: Hearth & Home Technologies, manufacturer of this appliance, reserves the right to alter its products, their specifi cations and/or price without notice.

Quadra-Fire is a registered trademark of Hearth & Home

Technologies.


R


2

Getting Started

A. Design, Installation & Location Consider ations

Consideration must be given to:

• Chimney and chimney connector required

It is a good idea to plan your installation on paper, using exact measurements for clearances and fl oor protection, before actually beginning the installation. If you are not using an existing chimney, place the appliance where there will be a clear passage for a factory-built listed chimney through the ceiling and roof.

We recommend that a qualifi ed building inspector and your insurance company representative review your plans before and after installation

If this appliance is in an area where children may be near it is recommended that you purchase a decorative barrier to go in front of the appliance. Remember to always keep children away while it is operating and do not let anyone operate this appliance unless they are familiar with these operating instructions.

NOTE: Service Space

In order to replace the tube channel a clearance of 19 inches (483mm) is required on the right side of stove in order to remove the tubes with the stove in place.

If space is not available, the stove will have to be disconnected from the chimney to proceed with the tube replacement. See page 37.

B. Fire Safety

To provide reasonable fi re safety, the following should be given serious consideration:

1. Install at least one smoke detector on each fl oor of your home to ensure your safety. They should be located away from the heating appliance and close to the sleeping areas. Follow the smoke detector manufacturer’s placement and installation instructions, and be sure to maintain regularly.

2. A conveniently located Class A fire extinguisher to contend with small fires resulting from burning embers.

3. A practiced evacuation plan, consisting of at least two escape routes.

4. A plan to deal with a chimney fi re as follows:

In the event of a chimney fi re: a Evacuate the house immediately

WARNING

Fire Risk.

• Do not operate appliance before reading and understanding operating instructions.

• Failure to operate appliance properly may cause a house fi re.

CAUTION

Check building codes prior to installation.

• Installation MUST comply with local, regional, state and national codes and regulations.

• Consult insurance carrier, local building, fi re offi cials or authorities having jurisdiction about restrictions, installation inspection, and permits.

WARNING

Asphyxiation Risk.

• DO NOT CONNECT THIS UNIT TO A CHIM-

NEY FLUE SERVICING ANOTHER APPLI-

ANCE.

• DO NOT CONNECT TO ANY AIR DISTRIBU-

TION DUCT OR SYSTEM.

May allow fl ue gases to enter the house.


R


C. Negative Pressure

Draft is the pressure difference needed to vent appliances successfully. Considerations for successful draft include:

To minimize the affects of negative air pressure the following must be considered:

• Preventing negative pressure

• Location of appliance and chimney

• Install the outside air kit. Install the intake on the side of the house towards prevailing winds during the heating season.

Negative pressure results from the imbalance of air available for the stove to operate properly. Causes for this imbalance include:

• Exhaust fans (kitchen, bath) etc.)

• Ensure adequate outdoor air is supplied for combustion appliances and exhaust equipment.

• Ensure furnace and air conditioning return vents are not located in the immediate vicinity of the appliance,

• Combustion air requirements for furnaces, water heaters and other combustion appliances

• Avoid installing the appliance near doors, walkways or small isolated spaces.

• Location of return-air vents to furnace or air conditioning

• Recessed lighting should be of “sealed can” design; attic hatches weather stripped or sealed; and attic mounted duckwork and air handler joints and seams taped or sealed.

• Imbalances of HVAC air handling system

• Upper level air leaks

• lighting

• Attic hatch opening

• leaks

WARNING


• Negative pressure can cause spillage of combustion fumes, soot and carbon monoxide.

• Appliance needs to draft properly for safety.

Recommended Location:

• Above peak

Recommended Location:

• Above peak

• Inside heated space

Marginal Location:

• Wind loading possible

Marginal Location:

• Below peak

Location NOT recommended:

• Not the highest point of the roof

• Wind loading possible

Recommended:

• Insulated exterior chase in cooler climates

Location NOT recommended:

• Too close to tree

• Below adjacent structure

• Lower roof line

• Avoid outside wall

Windward

Leeward

Multi-level Roofs

Figure 6.1

Recommended:

Outside Air Intake on windward side

Page 6 7033-277H

NOT recommended:

Outside Air Intake on leeward side

September 1, 2010

R


D. Flue Draft Considerations

Location of the appliance and chimney will affect performance. As shown in Figure 6.1

on page 6 the chimney should:

• Be installed through the warm space enclosed by the building envelope. This helps to produce more draft, especially during lighting and die down of the fi re.

• Penetrate the highest part of the roof. This minimizes the affects of wind turbulence and down drafts.

• Consider the appliance location in order to avoid fl oor and ceiling attic joists and rafters.

F. Tools And Supplies Needed

Before beginning the installation be sure that the following tools and building supplies are available.

Reciprocating saw

Pliers

Hammer

Phillips Head Screwdriver

Flat Blade Screwdriver

Plumb Line

Level

Tape Measure

Framing Material

Hi-Temp Caulking Material

Gloves

Framing Square

Electric Drill & Bits (1/4”)

Safety Glasses

1/2 in. - 3/4 in. length, #6 or

#8 self drilling screws (need 3 per pipe section connection)

Exterior conditions such as roof line, surrounding trees, prevailing winds and nearby hills can influence stove performance. Your local dealer is the expert in your geographic area and can usually make suggestions or discover solutions that will easily correct your fl ue problem.

To be sure that your appliance burns properly, the chimney draft (static pressure) should be approximately -.04 inch water column (W.C.) during a low burn and -.10 inch W.C. during a high burn, measured 6 inches (152mm) above the top of the appliance after one hour of operation at each burn setting.

G. Inspect Appliance & Components and

1.

2.

Pre-Use Check List

NOTE : These are guidelines only, and may vary somewhat for individual installations.

E. Venting Systems

The venting system consists of a chimney connector (also known as stove pipe) and a chimney. These get extremely hot during use. Temperatures inside the chimney may exceed 2000



F (1100



C) in the event of a creosote fi re. To protect against the possibility of a house fi re, the chimney connector and chimney must be properly installed and maintained.

An approved thimble must be used when a connection is made through a combustible wall to a chimney. A chimney support package must be used when a connection is made through the ceiling to a prefabricated chimney. These accessories are absolutely necessary to provide safe clearances to combustible wall and ceiling material. Follow venting manufacturer’s clearances when installing venting system.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

Place the appliance in a location near the fi nal installation area and follow the procedures below:

Open the appliance and remove all the parts and articles packed inside the Component Pack. Inspect all the parts and glass for shipping damage. Contact your dealer if any irregularities are noticed.

All safety warnings have been read and followed.

This Owner’s Manual has been read.

Floor protection requirements have been met.

Venting is properly installed.

The proper clearances from the appliance and chimney to combustible materials have been met.

The masonry chimney is inspected by a professional and is clean, or the factory built metal chimney is installed according to the manufacturer’s instructions and clearances.

The chimney meets the required minimum height.

All labels have been removed from the glass door.

Plated surfaces have been wiped clean, if applicable

A power outlet is available nearby if installing optional blower assembly.

WARNING


• Do NOT connect this unit to a chimney fl ue servicing another appliance.

• Do NOT connect to any air distributon duct or system.


September 1, 2010 7033-277H

WARNING

Fire Risk.

Inspect appliance and components for damage.

Damaged parts may impair safe operation.

• Do NOT install damaged components.

• Do NOT install incomplete components.

• Do NOT install substitute components.

Report damaged parts to dealer.

Page 7


H. Typical Stove Systems

Stove system with masonry chimney consists of:

• Chimney Connector (stove pipe)

• Hearth Pad Floor Protection

Spark Arrestor Cap

Concrete Cap

Rafter

1" (25mm) Clearance

With Firestop

Ceiling Joist

Combustible Wall

Fireclay Flue Liner

With Air Space

Flashing

Eave

Thimble,

12" (305mm)

Of Brick

Floor

Protector

Sheathing

Outside Air Rear Vent

Outside Air

Termination Cap

Airtight

Cleanout Door

Figure 8.1 Masonry Chimney

Stove system with prefabricated metal chimney consists of:

• Chimney Connector

(stove pipe)

• Thimble (for exterior chimney)

Listed Termination Cap

Roof Brace (if required)

Storm Collar

Flashing

Listed Chimney


Storm Collar

Flashing

• Storm Collar and Flashing

• Hearth Pad Floor Protection

Trim Collar on

Inside Wall

Chimney

Connector

Listed Chimney

Insulated " T "

Wall Support

Thimble

Ceiling Support

Chimney

Connector

Floor

Protector

Floor

Protector

R

Page 8

Figure 8.2 Exterior Prefabricated Chimney

7033-277H

Figure 8.3 Interior Prefabricated Chimney

September 1, 2010


R

3

Dimensions and Clearances

A. Appliance Dimensions

NOTE: Flue Collar size is 6 inch

(152mm) diameter (ID)

30 in.

(762mm)

15-1/16 in.

(383mm)

10-15/16 in.

(271mm)

18-15/16 in.

(475mm)

14-15/16 in.

(373mm)


9-15/16 in.

(237mm)

25 in. (635mm)

CL

12-1/2 in.

(318mm)

Figure 9.1 Front View

26-11/16 in. (668mm)

24-5/16 in. (618mm)

CL

6-11/16 in.

(170mm)

11-1/2 in.

(292mm)

16 in. (406mm)

September 1, 2010

Figure 9.2 Side View

20-3/4 in. (527mm)

7033-277H

4-1/2 in

(108mm)

Outside Air

Connection

Page 9


Appliance Dimensions (Cont’d)

3100 Step Top Pedestal Model

25 in. (635mm)

9-5/16 in.

(237mm)

CL

12-1/2 in.

(318mm )

34-1/4 in.

(870mm)

18 in.

(457mm )

Figure 10.1

26-11/16 in.(678mm)

24-5/16 in. (618mm)

15-3/8 in. (391mm)

3100 Step Top Leg Model

33-1/8 in.

(841mm)

19-1/16 in.

(484mm)

15-1/16 in.

(383mm)

14-15/16 in.

(379mm)

10-15/16 in.

(278mm)

23-7/8 in.

(606mm)

Figure 10.3

3-11/16 in. (94mm)

6-11/16 in.

(170mm)

3-1/2 in.

(89mm)

R

10-3/8 in.

(264mm)

16 in. (406mm)

Figure 10.2

Page 10

20-3/4 in. (527mm)

11-1/2 in.

(292mm)

Figure 10.4

7033-277H

21-1/8 in. (537mm)

September 1, 2010

R


B. Clearances to Combustibles (UL and ULC)

BACKWALL / SIDEWALL

NOTE: Clearances may only be reduced by means approved by the regulatory authority having jurisdiction

A B

C

D

H

*

CORNER INSTALLATION

E

F

90° OFF TOP

UP & OUT CEILING

CLEARANCE

STOVE TO CEILING

CLEARANCE

E

F

MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS In Inches & (Millimeters)

NOTE: All "A" , "C" and "F" Dimensions are to the inside diameter of the flue collar.

ALCOVE SIDE VIEW

G

A

B

ALCOVE TOP VIEW

C

D

INSTALLATION: Full Vertical OR Horizontal with Minimum 2 FT Vertical Off Stove Top


Flat Top Model

Step-Top Model

15.25 (387) 11.75 (298) 25.5 (648) 16 (406) 8 (203) 17 (432) 48 (1220) 12 (305)

12 (305) 8.5 (216) 22 (559) 12.5 (318) 5.5 (140 14.5 (368) 48 (1220) 12 (305)


Flat Top Model

Step-Top Model

10.5 (267) 6.5 (165) 22 (559) 13 (330) 6.5 (165) 15.5 (394) 48 (1220) 9 (229)

10 (228) 6 (152) 20.5 (521) 11 (279) 4 (102) 13 (330) 48 (1220) 9 (229)

INSTALLATION: 90° Elbow Off Top of Stove Through Backwall


Flat Top Model

Step-Top Model


Flat Top Model

Step-Top Model

12 (305) 8.5 (216) 22 (559) 13 (330)

10 (254) 6 (152) 20.5 (521) 11 (279)

8 (203)

5.5 (140)

17 (432)

14.5 (368)

48 (1220)

48 (1220)

12 (305)

12 (305)

8 (203) 4.5 (114) 17.5 (445) 8.5 (216) 6.5 (165) 15.5 (394) 48 (1220) 9 (229)

10 (254) 6 (152) 20.5 (521) 11 (279) 4 (102) 13 (330) 48 (1220) 9 (229)

INSTALLATION: ALCOVE Six inch (6") (152mm) diameter listed Double Wall air insulated connector pipe with UL103 HT* listed factory-built Class "A" chimney, or a masonry chimney. (Mobile Home must be equipped with a spark arrestor). Maximum depth of Alcove shall be no more than 48 inches (1220mm) with a minimum height of 48 inches (1220mm) to top of unit, and the referenced clearances.

*In Canada must comply with CAN/ULC-S269 M87 for the 650 o C Factory-built chimney.


Flat Top Model

Step-Top Model

11.75 (298) 8.25 (210) 23.5 (597) 14.5 (368)

10 (254) 6.5 (152) 20.5 (521) 11 (279)

* SEE PIPE MANUFACTURERS CLEARANCES - NOT TESTED

N/A

N/A

N/A

N/A

48 (1220)

48 (1220)

*

*


WARNING

Fire Risk.

• Comply with all minimum clearances to combustibles as specifi ed.

• Failure to comply may cause house fi re.

September 1, 2010

In order to replace the tube channel assembly a clearance of 19 inches (483mm) is required on the right side of stove in order to remove the tubes with the stove in place.

If space is not available, the stove will have to be disconnected from the chimney to proceed with the tube replacement.

7033-277H Page 11


4

Installation

A. Hearth Protection Requirements

FLOOR PROTECTION: Floor protector must be non-combustible material, extending beneath heater and to the front, sides and rear as indicated. The fl oor must be non-combustible or otherwise adequately protected from radiant heat given off by the unit and from sparks and falling embers. A layer of thin brick or ceramic tile over a combustible fl oor is not suffi cient.

In Canada, similar fl oor protection must be provided 18 inches (457mm) in front and 8 inches (203mm) from the sides and rear of the stove. * See exception.

*EXCEPTION: Non-combustible fl oor protections must extend beneath the fl ue pipe when installed with horizontal venting and extend 2 inches (51mm) beyond each side.

See Figure 12.4.

For the Millennium Model In US installations, it is necessary to install a fl oor protector of a minimum of 3/8 inch

(9.5mm) thick metal clad millboard or equivalent a minimum of 16 inches (406mm) in front of glass and 8 inches (203mm) to both sides of the fuel loading door. Open the door and measure 8 inches (203mm) from the side edge of the opening in the face of the appliance. * See exception.


WARNING

Fire Risk.

• Hearth pads must be installed exactly as specified.

High temperatures or hot embers may ignite concealed combustibles.

R

51-1/16 in.

opti co onal ve ra ge

31-3/4 in.

31-5/8 in.

4-7/8 in.

3-1/8 in.

Fuel loading door

39-5/8 in.

minimum

16 in. from glass

8 in.

38-15/16 in.

135°

27-3/8 in.

31-5/8 in.

minimum

Figure 12.1

203mm (8 in.)

USA

3-1/16 in.

Figure 12.3

USA required

Canada recommended

USA

203mm

(8 in.)

203mm

(8 in.)

1260mm

(49-5/8 in.) minimum

457mm (18 in.)

1041mm (41 in.) minimum

CANADA

7033-277H

Must extend 2 in. (51mm) beyond each side of pipe (shaded area)

Figure 12.4

September 1, 2010

Figure 12.2

Page 12

R


Step-Top Uni-Body Model

For the Step Top Pedestal Model In US installations, it is necessary to install a fl oor protector of a minimum of

3/8 inch (9.5mm) thick metal clad millboard or equivalent a minimum of 16 inches (406mm) in front of glass and

8 inches (203mm) to both sides of the fuel loading door.

Open the door and measure 8 inches (203mm) from the side edge of the opening in the face of the appliance.

* See page 12 for Canadian clearances and horizontal venting exception.

For the Step Top Leg Model In US installations, it is necessary to install a fl oor protector of a minimum thickness of 1-1/4 inch (32mm) or 1/2 inch of “k” value of 0.84 or R value = 0.59 thick metal clad millboard or equivalent a minimum of 16 inches

(406mm) in front of glass and 8 inches (203mm) to both sides of the fuel loading door. Open the door and measure 8 inches

(203mm) from the side edge of the opening in the face of the appliance. * See page 12 for Canadian clearances and horizontal venting exception. See Page 24 for calculation for alternate fl oor protection.

48-9/16 in.

31-5/8 in.

optional coverage

29-1/4 in.

Figure 13.1

4-3/4 in.

Fuel loading door

3-1/4 in

.

39-5/8 in.

minimum

16 in. from glass

8 in.

31-5/8 in.

minimum

USA

Figure 13.3

38-15/16 in.

135°

27-5/16 in.

3-1/16 in.

USA

USA required

Canada recommended

203mm

(8 in.)

203mm (8 in.)

203mm

(8 in.)

1254mm

(49-3/8 in.) minimum

457mm (18 in.)

Must extend 2 in. (51mm) beyond each side of pipe (shaded area)

1041mm (41 in.) minimum

CANADA

Figure 13.2

Figure 13.4

NOTE: • Illustrations and photos refl ect typical installations and are FOR DESIGN PURPOSES ONLY.

• I llustrations/diagrams are not drawn to scale.

• Actual installation may vary due to individual design preference

• Hearth & Home Technologies reserves the right to alter its products.


R


B. Outside Air Kit Installation

A source of air (oxygen) is necessary in order for combustion to take place. Whatever combustion air is consumed by the fi re must be replaced. Air is replaced via air leakage around windows and under doors. In homes that have tightly sealed doors and windows, an outside air source is needed. An optional Outside Air Kit is available.

Included in OAK-ACC: Termination cap, (2) wire ties, flex adapter, and fasteners

Included in SRV7033-041 : Cover plate and sealing rope (see

Floor Installation Alternative below,

Figure 14.2

)

Items Needed for Installation (not supplied)

• 4 inch fl ex aluminum pipe, or if using alternate material, then it shall be made from durable, non-combustible, heat resistant material up to 350 o

F. Cut the pipe to the required length for your installation.

• Phillips head screw driver

• Drills and saws necessary for cutting holes through the wall or fl ooring in your home.

1. Remove all materials from packing box.

2. Using a #2 Phillips screw driver attach the fl ex adapter to the stove using 4 screws. Figure 14.1 base of the pedestal.

4 .

Floor & Rear Installation: Cut a 4 inch (102mm) hole in outside wall or fl oor to accommodate outside air piping. Use 4 inch (102mm) aluminum metal fl ex or rigid piping to directly connect outside air to appliance intake. Use the supplied termination cap with a rodent screen. Seal between the wall (or fl oor) and the pipe with silicone to prevent moisture penetration.

WARNING

Fire Risk.


Do not draw outside combustion air from:

• Enclosed space such as an attic or garage

• Close proximity to exhaust vents or chimneys

Fumes or odor may result

WARNING


Outside air inlet must be located to prevent blockage from:

• Leaves

• Snow or ice

Block may cause combustion air starvation

Smoke spillage may set off alarms or irritate sensitive individuals.

WARNING


Length of outside air supply duct shall NOT exceed the length of the vertical height of the exhaust fl ue.

• Fire will not burn properly

• Smoke spillage occurs when door is opened due to air starvation.

5. Floor Installation Alternative: In some instances you may not be able to install the fl ex pipe as show in Figure

14.1.

If that is the case, you will need to order SRV7033-

041 which includes a cover plate and sealing rope as shown in Figure 14.2.

The goal is to seal the pedestal so no room air can leak into the pedestal or for cold air infi ltration.

Flex Adapter

Wire Tie

Termination

Cap

Rope to Seal

Pedestal

Cover

Plate

For Floor Installations Remove

Circular “Knock-Out” in Base of Pedestal.

Flex Line

Wire Tie

Figure 14.1 - Floor & Rear Installation

Page 14 7033-277H

Figure 14.2 - Floor Installation Alternative

September 1, 2010

Do not remove.

R

C. Blower (Optional)

1. Remove the 3 bolts (1/4”-20 Phillips head) on the outer skin at the bottom rear of appliance.

2. Align holes in mounting fl ange of blower with bolt holes in appliance. Blower should be positioned at bottom of rear outer skin as shown in Figure 15.1

.

3. Re-insert and tighten bolts, securing blower onto outer wall of appliance.

4. Place the bracket containing the snap disc and magnet under the bottom left rear corner as shown in Figure 15.1

.

See for detailed operating instructions for the blower and snap disc.

Secure blower with 3 bolts

Snap Disc

Bracket with Magnet


CAUTION

Shock Risk .

• Do NOT remove grounding prong from plug.

• Plug directly into properly grounded 3 prong receptacle.

• Route cord away from appliance.

• Do NOT route cord under or in front of appliance.

Secure wires with wire tie

MANUAL

FAN

AUTO

LOW

HIGH

OFF

MANUAL: Over-rides the

Snap Disc

AUTO: Fan will turn ON/OFF

Automatically by the Snap Disc

Controls the Fan Speed

Figure 15.1

13-15/16 in. (355mm)

Figure 15.2 - Blower Housing Dimensions

September 1, 2010 7033-277H

3-1/8 in.

(80mm)

4-13/16 in.

(122mm)

4-15/16 in.

(125mm)

Page 15


5

Chimney Requirements

A. Venting Components

Chimney Connector:

It is also known as fl ue pipe or stove pipe. The chimney connector joins the stove to the chimney. It must be a 6 inch

(152mm) minimum diameter 24 gauge mild steel black or

26 gauge blued steel, or an approved air-insulated double wall venting pipe.

Thimble :

A manufactured or site-constructed device installed in combustible walls through which the chimney connector passes to the chimney. It is intended to keep the walls from igniting. Site constructed thimbles must meet

NFPA 211 Standards. Prefabricated must be suitable for use with selected chimney and meet UL103 Type HT

Standards. Follow instructions provided by the manufacturer for manufactured thimbles for masonry chimney and prefabricated chimneys.

Chimney :

The chimney can be new or existing, masonry or prefabricated and must meet the following minimum requirements specifi ed in Section 5B.

B. Chimney Systems

Prefabricated Metal Chimney

• Must be minimum 6 inch (152mm) diameter (ID) high temperature chimney listed to UL 103 HT (2100 o

F) or

ULC S629M.

• Must use components required by the manufacturer for installation.

• Must maintain clearances required by the manufacturer for installation.

• Refer to manufacturers instructions for installation.

NOTE: I n Canada when using a factory-built chimney it must be safety listed, Type UL103 HT (2100 o

F) CLASS “A” or conforming to CAN/ULC-S629M, STANDARD FOR 650 o

C

FACTORY-BUILT CHIMNEYS.


Storm Collar

R

Flashing


Roof Brace (if required)

Listed Chimney

Storm Collar

Flashing

Ceiling Support

Chimney

Connector

Trim Collar on

Inside Wall

Chimney

Connector

Listed Chimney

Insulated " T "

Wall Support

Thimble

Floor

Protector Floor

Protector

Figure 16.1 Prefabricated Exterior Chimney

Page 16 7033-277H

Figure 16.2 - Prefabricated Interior Chimney

September 1, 2010

R


Thimble

Site constructed for masonry chimney installation:

Components

• A minimum length of 12 inches [305mm] (longer for thicker walls) of solid insulated factory-built chimney length constructed to UL 103 Type HT 6 inch (152mm) inside diameter. Chimney needs to extend a minimum of 2 inches (51mm) from the interior wall and a minimum of 1 inch (25mm) from the exterior wall.

• Wall spacer, trim collar and wall band to fi t solid pack chimney selected.

ceiling

Minimum18.0”

NFPA 211

17.0” OD 14.0” ID

8.0”

Wall

13.5” below ceiling to top of opening or top of opening is a min.of

4.5” below min.clearance specified by connector mfg.

1.5 2x2 framing stud

2.0 min air clearance

1.0 min air clearance

4.5

1.5”

2.0”

1.0”

• Minimum 8 inch (203mm) diameter clay liner section (if not already present in chimney) and refractory mortar.

Air Clearances

• Masonry chimney clearance must meet NFPA 211 minimum requirement of 2 inches (51mm) to sheet metal supports and combustibles.

• Minimum of 1 inch (25mm) clearance around the chimney connector.

Center of Hole

Thimble

Include depth of hearth pad

1.5”

2.0”

1.0”

• Top of wall opening is a minimum of 13-1/2 inches

(343mm) from ceiling or 4-1/2 inches (114mm) below minimum clearance specifi ed by chimney connector manufacturer. NFPA 211 minimum vertical clearance of

18 inches (457mm) from chimney connector and ceiling or minimum recommended by chimney connector manufacturer. Figure 17.1.

Instructions:

Figure 17.1

Solid Pack Chimney with Metal Supports as a Thimble

1. Open inside wall at proper height for the chimney connector to entry the masonry chimney. Figure 17.1

2. Entry hole to masonry chimney must be lined with an 8 inch (203mm) minimum diameter clay liner, or equivalent, secured with refractory mortar.

3. Construct a 17 inch x 17 inch (432mm x 432mm) outside dimension frame from 2 x 2 framing lumber to fi t into wall opening. Inside opening of frame should be no less than 14 inch x 14 inch (356mm x 356mm).

Figure 17.1.

4. Attach the wall spacer to the chimney side of the frame.

5. Nail the frame into the wall opening. The spacer should be on the chimney side.

6. Insert the section of the solid insulated chimney into the outer wall of the masonry chimney.

7. Tightly secure the length of the solid insulated chimney with the wall band to the masonry chimney.

8. Insert a section of chimney connector into the chimney.

Make sure it does not protrude past the edge of the clay chimney liner inside the chimney.

9. Seal the end of the chimney connector to the clay liner with refractory mortar.

10. Install trim collar around the sold pack chimney section.

Trim Collar

Chimney Section with 2 inch

(51mm)

Clearance to

Combustibles

Figure 17.2

Chimney

Connector

WARNING

Fire Clay Flue

Liner with Airspace

Masonry

Chimney

Wall Spacer

Wall Band to

Secure Chimney

Section

Wood Studs Used for Framing - Spaced

2 inch (51mm) clearance from

Masonry Chimney

Fire Risk.

Do NOT pack insulation or other combustibles between spacers.

• ALWAYS maintain specifi ed clearances around venting and spacers.

• Install spacers as specifi ed.

Failure to keep insulation or other material away from vent pipe may cause fi re.


R


Solid Pack Chimney with Metal Supports as a

Thimble (Cont’d)

Min. Chimney Clearance to

Wall Spacer and

Combustibles - 2 inch (51mm)

Min. Clearance

2 inch (51mm)

Chimney Flue

Liner

Fireclay

Liner or

Equivalent

1 inch (25mm) Air

Space to Chimney

Section

Chimney

Connector

Chimney Section

Trim Collar

Masonry Chimney

Constructed to NFPA 211

Wall Band

Wall Spacer

Figure 18.1

C. Installing Chimney Components

Chimney Connector

Single wall connector or stove pipe.

This must be at least 24 gauge mild steel or 26 gauge blue steel. The sections must be attached to the appliance and to each other with the crimped (male) end pointing toward the stove. All joints, including the connection at the fl ue collar, should be secured with 3 sheet metal screws. Make sure to follow the minimum clearances to combustibles. Where passage through the wall, or partition of combustible construction is desired in Canada, the installation shall conform to CAN/CSA-B365.

Factory-built listed chimney connector (vented).

A listed connector (vented) must be used when installing this unit in a mobile home. The listed connectors must conform to each other to ensure a proper fi t and seal.

Chimney Height / Rise and Run

This product was designed for and tested on a 6 inch (152mm) chimney, 14 to 16 feet (420-480cm) high, (includes stove height) measured from the base of the appliance. The further your stack height or diameter varies from this confi guration, the possibility of performance problems exists.

Chimney height may need to be increased by 2 - 3% per each 1000 feet above sea level. It is not recommended to use offsets or elbows at altitudes above 4000 feet above sea level or when there are other factors that affect fl ue draft.

WARNING

Fire Risk .

Inspection of Chimney:

• Chimney must be in good condition.

• Meets minimum standard of NFPA 211

• Factory-built chimney must be 6 inch

(152mm) UL103 HT.

Crimped

End

Toward

Stove

Flue Gas

Direction

Secure pipe sections with a minimum of 3 screws

Figure 18.2 Chimney Connector (Stove Pipe)

WARNING

Fire Risk.

Follow Chimney Connector Manufacturer’s

Instructions for Proper Installation.

ONLY use connector:

• Within the room, between appliance and ceiling or wall.

Connector shall NOT pass through:

• Attic or roof space

• Closet or similar concealed space

• Floor or ceiling

Maintain minimum clearances to combustibles WARNING


• DO NOT CONNECT THIS UNIT TO A CHIM-

NEY FLUE SERVICING ANOTHER APPLI-

ANCE.

• DO NOT CONNECT TO ANY AIR DISTRI-

BUTION DUCT OR SYSTEM.


WARNING

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional information consult a qualifi ed installer, service agency or your dealer.


R


D. Chimney Termination Requirements

Follow manufacturers instructions for clearance, securing, fl ashing and terminating the chimney.

•

Must have an approved and listed cap

•

Must not be located where it will become plugged by snow or other material

• Must terminate at least 3 feet (91cm) above the roof and at least 2 feet (61cm) above any portion of the roof within 10 feet (305cm).

NOTE:

• Chimney performance may vary.

• Trees, buildings, roof lines and wind conditions affect performance.

• Chimney height may need adjustment if smoking or overdraft occurs.

• Must be located away from trees or other structures

E. 2-10-3 Rule

These are safety requirements and are not meant to assure proper fl ue draft.

Less than 10 ft. (305cm)

2 ft. (61cm)

3 ft. (91cm)

Minimum

3 ft. (91cm)

Minimum

2 ft. (61cm)

10 ft. (305cm) To Nearest Roofline

Figure 19.1

Pitched Roof

10 ft. (305cm) or more

Wall or Parapet

Less than 10 ft. (305cm)

3 ft. (91cm) Minimum

3 ft. (91cm) Minimum

2 ft. (61cm)Minimum

Figure 19.2

September 1, 2010

Flat Roof

7033-277H Page 19


6

Mobile Home Installation

You must use a Quadra-Fire Outside Air Kit Part

OAK-ACC and (depending on fl oor installation), Part

SRV7033-041 for installation in a mobile home.

SparkArestor Cap

1. An outside air inlet must be provided for combustion See page 14 for installation information.

2. Appliance must be secured to the mobile home structure by bolting the pedestal through hearth pad and into fl oor.

3. Appliance must be grounded with #8 solid copper grounding wire or equivalent and terminated at each end with N.E.C. approved grounding device.

4. Appliance must be installed with an approved UL103 HT ventilated chimney connector, UL103 HT chimney, and terminal cap with spark arrestor. Never use a single wall connector (stove pipe) in a mobile home installation. Use only double-wall connector pipe, Dura-Vent DVL, Selkirk metalbestos DS or Security DL double-wall connector or any listed double-wall connector pipe.

5. In Canada, this appliance must be connected to a 6 inch

(152mm) factory-built chimney conforming to CAN/ULC-

629M, STANDARD FOR FACTORY BUILT CHIMNEYS.

6. Follow the chimney and chimney connector manufacturer’s instructions when installing the fl ue system for use in a mobile home.

7. Maintain clearance to combustibles.

8. Floor protection requirements must be followed precisely.

Storm Collar

Joist Shield/Firestop

Floor Protector

Outside Air Floor Vent

Roof Flashing

Double wall connector pipe

OutsideAir

Rear Vent

9. Use silicone to create an effective vapor barrier at the location where the chimney or other component penetrates to the exterior of the structure.

NOTE: Offsets from the vertical, not exceeding 45°, are allowed per Section 905(a) of the Uniform Mechanical Code

(UMC). Offsets greater than 45° are considered horizontal and are also allowed, providing the horizontal run does not exceed 75% of the vertical height of the vent. Construction, clearance and termination must be in compliance with the

UMC Table 9C. This installation must also comply with NFPA

211.

NOTE: Top sections of chimney must be removable to allow maximum clearance of 13.5 feet (411cm) from ground level for transportation purposes.

10. Burn wood only. Other types of fuels may generate poisonous gases (e.g., carbon monoxide).

Figure 20.1

CAUTION

THE STRUCTURAL INTEGRITY OF THE MOBILE HOME

FLOOR, WALL AND CEILING/ROOF MUST BE MAIN-

TAINED

Do NOT cut through:

• Floor joist, wall, studs or ceiling trusses.

• Any supporting material that would affect the structural integrity.

WARNING


11. If unit burns poorly while an exhaust blower is on in home, (i.e., range hood), increase combustion air.

12. Installation shall be in accordance with the Manufacturers

Home & Safety Standard (HUD) CFR 3280, Part 24.

NEVER INSTALL IN A SLEEPING ROOM.

Consumes oxygen in the room.


R

R


7

Appliance Set Up

A. Pedestal Assembly and Ash Removal

System (ARS) Installation for Step Top

Uni-body

NOTE: The Ash Removal System, must be installed fi rst before installing the pedestal.

ARS Cover

Included in Kit : Door assembly, door handle & magnet, ash drawer, fastener package. A cover plate that is required for a fl oor outside air installation on a pedestal model is also included, If not needed, discard.

Tools Required: Phillips head screwdriver, 7/16 socket wrench, 3/32 and 5/36 Allen wrench.

Begin installing the ARS System.

1. Remove 2 front bricks as shown in Figure 21.1.

2. Lay body of stove on its back on a protective pad or pallet.

3. Remove the 2 nuts and 2 bolts holding the channel in place and set the channel aside. Discard the 2 nuts.

Install the gasket over the 8 protruding screws.

The glossy side of the gasket needs to go against the fi rebox bottom.

It is important the gasket is not put on upside down as it could compromise its sealing capabilities.

Figure 21.2.

4. Install ash door assembly by sliding the rod at an angle into the slot on the left side. As the rod starts passing through the slot, slide the handle over the rod and then fi nish pushing the rod through the slot.

Slide the ash door over the 8 screws protruding from the bottom of the stove. Secure with nuts and washers provided. Figure 21.2.

5. Re-install handle using a 3/32 Allen wrench to tighten the set screw in the door handle. The set screw needs to be snug. Figure 21.3.

6. Install magnet using a Phillips head screw driver. This magnet will hold the door handle in an open position which in turn holds the ash door open so ashes can be brushed into the ash drawer. Figure 21.2.

WARNING

Do NOT operate before fully assembling components.

Burning your stove without a pedestal or leg kit attached:

• Will void your warranty.

• May result in property damage or personal injury.

September 1, 2010

2

2

Remove 2 bricks for

installation and then re-install

Figure 21.1

Door Handle

Magnet

Start sliding rod at an angle into slot, slide handle over rod and then finish pushing through slot.

Figure 21.2

Set Screw

(align with flat side of rod)

Glossy side of

Gasket against firebox bottom

Ash Door

Assembly

7033-277H

Door handle must be in open position to tighten set screw

Figure 21.3

Lay stove flat on protective padding or pallet

Ash Door Rod shown in installed position

Page 21


Pedestal and Ash Removal System (Cont’d)

Installing Pedestal Assembly

1. Remove screws on adapter and slide pedestal over adapter on bottom of stove. Figure 22.1.

2. Line up holes in sides of pedestal with holes in adapter.

3. Securely tighten pedestal into place.

4. Carefully stand stove up and place in desired location.

5. Slip wooden decorative strips onto pedestal edges.

Finishing the ARS Installation

1. Re-install the ARS channel that was removed in Step 3 on page one and secure with 2 bolts previously removed.

Set the cover into the ARS channel Replace the 2 front cut bricks. Figure 22.2.

2. Install the ash drawer.

3. Check to make sure baffl e boards and ceramic blanket are in their proper locations. (see page 29) .

NOTE: If installing a fl oor installation of an outside air kit on a

Step Top model with a pedestal assembly you must attach the enclosed cover plate to the back of the stove. Other wise you may discard this piece.

Figure 22.3.

Figure 22.2

Cover

Replace both bricks back into firebox

ARS

Channel

R

Adapters

Ash Removel

Drawer

Cover

Plate

Figure 22.3

Oak

Pedestal

Trim

Figure 22.1


R

B. Leg Kit and Ash Removal Installation

(ARS) for Step Top Uni-Body

NOTE: The Ash Removal System, must be installed fi rst before installing the legs.

Begin installing the ARS System.

1. Follow steps 1 through 6 on page 22. See also Figures

21.2 and 21.3.

Installing Leg Kit

1. Remove leg mounting brackets packaged inside fi rebox.

2. Attach the 2 bottom screws of the mounting brackets to the bottom of the stove with 1/4”-20 Phillips head screws.

These screws are located in the component pack .

Leave the bottom 2 screws loose so you can slide the ash pan assembly bottom slots over the screw heads. This allows the weight of the ash pan to rest on the screws while you are attaching the top 2 screws. Once the ash pan is attached, tighten all screws. Figure 23.2

.

3. Loosely assemble bolts into the corner of the mounting brackets for leg attachment. Figure 23.1.

4. Slide legs onto mounting brackets making sure the legs are up against the bracket and secure with bolts supplied.

There are leveling bolts in 2 legs. These leveling legs should be in opposite corners. Figure 23.1.

5. Carefully stand stove up and place in desired location.

Do NOT tilt up on the cast iron legs, it could damage the legs.

6. Use leveling bolts on legs to stabilize and level stove.

Finishing the ARS Installation

1. Follow steps 1 through 3 on page 22. See also Figure

22.2.

Leg Mounting Brackets are packaged inside firebox.


Lay stove flat on its back on protective padding or pallet

Ash Drawer

Figure 23.2

Leg Brackets

Insert 2 bottom screws loosely

CAUTION

Do NOT tilt the unit on the cast iron legs.

• Tilting could lead to property damage.

• Lift the unit upright and place it into position on the fl oor protector.

Figure 23.1

September 1, 2010

Leveling Legs at opposite corners

7033-277H Page 23

R


C. Door Handle Assembly

E. Calculating Alternate Floor Protection Material

1. Install washer on door handle shaft.

2. Slide door handle through door.

3. Install second washer(s) as shown.

4. Install key in groove.

5. Align groove in latch cam with key; slide latch cam over shaft

6. Install locknut but do not overtighten as the door handle needs to move smoothly.

7. Install spring handle turning in a counter-clockwise motion to desired location on door handle rod.

Thermal Conductivity: k value

The k value indicates the amount of heat (in BTU’s) that will fl ow in 1 hour through 1 square foot of a uniform material 1 inch thick for each degree (F) of temperature difference from one side of the material to the other. The LOWER the k factor means less heat is being conducted through the non-combustible material to the combustible material beneath it. The k value of a material must be equal or smaller then the required k value to be acceptable.

(foot 2 (hour) ( o F)

CAUTION

• Do NOT overtighten lock nut.

• Door handle needs to move smoothly.

Locknut

Latch Cam

Figure 24.1

Door Cross Section

(example)

Spacing

Washers

Door Handle

Square Key

Spring

Handle

D. Adjusting The Blower Speed Control

The blower speed control for this unit is adjusted at the factory, and normally does not require further adjustment.

Thermal Resistance: R value

The R value is a measure of a material’s resisteance to heat transfer. R value is convenient when more than one material is used since you can add the R values together, whereas you can not do this for k value. The HIGHER the R factor means less heat is being conducted through the non-combustible material to the combustible material beneath it. The R value of a material must be equal or larger then the required R value to be acceptable.

Converting k to R:

Divide 1 by k and multiply the results times the thickness in inches of the material.

R = 1/k x inches of thickness

Converting R to k:

Divide the inches of thickness by R.

k = inches of thickness/R

Calculatons:

Example: Floor protection requires k value of 0.84 and 3/4 inch thick.

Alternative material has a k value of 0.6 and is 3/4 inch thick.

Divide 0.6 by .75 = k value of 0.80. This k value is smaller than

0.84 and therefore is acceptable.

NOTE: When the speed control is turned clockwise, it will click on to high speed. Continue to turn the speed control clockwise to decrease the speed. At full clockwise, the blower should blow gently, but should not stop.

1. With the appliance plugged in, turn the speed control knob to slow (full clockwise).

2. With a small screwdriver, adjust the blower speed by turning the adjustment mechanism through the hole on the side of the speed control.

3. Adjust the speed so the blower runs slowly, but does not stop. Turn clockwise to slow the blower and counterclockwise to increase the speed.


R


8

Operating Instructions

A. Over-Firing Your Appliance

B. Wood Selection & Storage (Cont’d)

WARNING

Fire Risk

Do not over-fi re.

Over-fi ring may ignite creosote or will damage the stove and chimney.

To prevent over-fi ring your stove, DO NOT: to keep the chimney hot for as long as it takes to dry the wood out - about one hour. It is a waste of energy to burn unseasoned wood of any kind.

Dead wood lying on the forest fl oor should be considered wet, and requires full seasoning time. Standing dead wood can be considered to be about 2/3 seasoned. To tell if wood is dry enough to burn, check the ends of the logs. If there are cracks radiating in all directions from the center, it is dry.

If your wood sizzles in the fi re, even though the surface is dry, it may not be fully cured.

• Overload with wood

• Burn trash or large amounts of scrap lumber

• Permit too much air to the fi re

1. Symptoms of Over-Firing

Symptoms of over-fi ring may include one or more of the following:

• Chimney connector or appliance glowing

• Roaring, rumbling noises

Splitting wood before it is stored reduces drying time. Wood should be stacked so that both ends of each piece are exposed to air, since more drying occurs through the cut ends than the sides. This is true even with wood that has been split. Store wood under cover, such as in a shed, or covered with a tarp, plastic, tar paper, sheets of scrap plywood, etc., as uncovered wood can absorb water from rain or snow, delaying the seasoning process.

• Loud cracking or banging sounds

C. Burning Process

2. What To Do if Your Stove is Over-Firing

• Immediately close the door and air controls to reduce air supply to the fi re.

• If you suspect a chimney fi re, call the fi re department and evacuate your house.

In recent years there has been an increasing concern about air quality. Much of the blame for poor air quality has been placed on the burning of wood for home heating. In order to improve the situation, we at Quadra-Fire have developed cleaner-burning woodstoves that surpass the requirements for emissions established by our governing agencies. These woodstoves, like any other appliances, must be properly operated in order to insure that they perform the way they are designed to perform. Improper operation can turn most any wood stove into a smoldering environmental hazard.

• Contact your local chimney professional and have your stove and stove pipe inspected for any damage.

1. Kindling or First Stage

• Do not use your stove until the chimney professional informs you it is safe to do so.

Hearth & Home Technologies WILL NOT warranty stoves that exhibit evidence of over-fi ring. Evidence of over-fi ring includes, but is not limited to:

• Warped air tube

• Deteriorated refractory brick retainers

It helps to know a little about the actual process of burning in order to understand what goes on inside a stove. The fi rst stage of burning is called the kindling stage. In this stage, the wood is heated to a temperature high enough to evaporate the moisture which is present in all wood. The wood will reach the boiling point of water (212°F) and will not get any hotter until the water is evaporated. This process takes heat from the coals and tends to cool the appliance.

B. Wood Selection & Storage

Burn only dry seasoned wood. Store wood under cover, out of the rain and snow. Dry and well-seasoned wood will not only minimize the chance of creosote formation, but will give you the most effi cient fi re. Even dry wood contains at least

15% moisture by weight, and should be burned hot enough

Fire requires three things to burn - fuel, air and heat. So, if heat is robbed from the appliance during the drying stage, the new load of wood has reduced the chances for a good clean burn. For this reason, it is always best to burn dry, seasoned fi rewood. When the wood isn’t dry, you must open the air controls and burn at a high burn setting for a longer time to start it burning. The heat generated from the fi re should be warming your home and establishing the fl ue draft, not evaporating the moisture out of wet, unseasoned wood, resulting in wasted heat.

Page 25 September 1, 2010 7033-277H

R


2. Second Stage

The next stage of burning, the secondary stage, is the period when the wood gives off fl ammable gases which burn above the fuel with bright fl ames. During this stage of burning it is very important that the fl ames be maintained and not allowed to go out. This will ensure the cleanest possible fi re. If the fl ames tend to go out, it is set too low for your burning conditions. The air control located at the upper right hand corner is used to adjust for burn rates. This is called the Burn Rate

Air Control. Figure 26.1.

3. Final Stage

T he fi nal stage of burning is the charcoal stage. This occurs when the fl ammable gases have been mostly burned and only charcoal remains. This is a naturally clean portion of the burn.

The coals burn with hot blue fl ames.

It is very important to reload your appliance while enough lively hot coals remain in order to provide the amount of heat needed to dry and rekindle the next load of wood. It is best to open the Burn Rate Air and Start-Up Air Controls before reloading . This livens up the coalbed and reduces excessive emissions (opacity/smoke). Open door slowly so that ash or smoke does not exit appliance through opening. You should also break up any large chunks and distribute the coals so that the new wood is laid on hot coals.

Air quality is important to all of us, and if we choose to use wood to heat our homes we should do so responsibly. To do this we need to learn to burn our stoves in the cleanest way possible. Doing this will allow us to continue using our wood stoves for many years to come.

The second function of the Start-Up Air Control is operation of the rear air system. The rear air is used primarily during a High Burn Rate. However, in some instances rear air is desired during normal operation to help with combustion of fuel towards the back of the fi rebox particularly when burning hardwoods. The rear air is controlled independently from the

ACC system. Slide the Start-Up Air Control between the fi rst and third marker as indicated on the label to allow rear air to enter the fi rebox. Figure 26.1.

2. Manual Timer Over-Ride

If you need to shut the ACC system off before it shuts itself off after 25 minutes (i.e. overfi re situation), reach down to the bottom right rear corner and pull the lever toward you.

Figure 26.2.

Burn Rate

Air Control

HIGH

MED

LOW

D. Automatic Combustion Control (ACC)

Typically, when you build a fi re, you open the air controls fully and monitor the fi re to prevent it from going into an overfi re situation and/or burning your wood up too quickly before you shut down the air controls to the desired burn rate. With the

Automatic Combustion Control (ACC) system, you do not have to continually monitor the fi re. Once you set the ACC system it will control the fi re for you. Follow the instructions below to learn how to operate your stove with ease.

E. Air Controls

1. Start-Up Air Control

The Start-Up Air Control has two primary functions. The fi rst function is to activate the Automatic Combustion Control system (ACC). This function is performed by sliding the control all the way back until it stops at the “HI” indicator on the label and then pulling forward to the front of the stove until it stops. This activates the ACC system and opens the front air channel and allows air to enter the front of the stove for approximately 25 minutes. The front air channel gradually shuts down until it is completely closed at the end of the 25 minutes. The fi re is now controlled by the air supplied by the

Burn Rate Air Control. This function should be performed each time you reload the stove. Figure 26.1.

Page 26 7033-277H

Figure 26.1

Start-Up

Air Control

Pull Forward to Shut Down

Figure 26.2

Manual

Timer (ACC)

Shut Down

September 1, 2010

R


2. Burn Rate Air Control

This air supply enters at the upper front of the fi rebox, near the top of the glass door. This preheated air supplies the necessary fresh oxygen to mix with the unburned gases, helping to create second, third and fourth combustions. This air is regulated by the Burn Rate Air Control. There are four settings

High, Medium-High, Medium-Low and Low. When the control is raised all the way up it is on the High setting and when pushed all the down it is on the Low setting. Figure 27.1.

4. Medium-Low Burn Rate - 10,000 to 15,000 BTU/hr

Raise the Burn Rate Air Control up to the bottom of the middle marker and stop. Slide the Start-Up Air

Control all the way back until it stops (HI marker) and then pull forward until it stops. This activates the timer system (ACC).

5. Low Burn Rate - Below 10,000 BTU/hr

Leave the Burn Rate Air Control at the bottom marker.

Slide the Start-Up Air Control all the way back until it stops (HI marker) and then pull forward until it stops.

This activates the timer system (ACC).

F. Burn Rates and Operating Effi ciency

For maximum operating effi ciency

1. This appliance has a timer system (ACC) that operates the stove at its maximum effi ciency removing any guess work for the homeowner. Follow the instructions below for each burn rate for the Start-Up Air Control and Burn

Rate Air Control. Figure 27.1.

2. Burn dry, well-seasoned wood.

Burn Rates

1. Starting a Fire and Reloading

Open both controls fully by raising the Burn Rate Air

Control all the way up until it stops and slide the Start-up

Air Control back until it stops. After loading the stove with wood and starting the fi re, set both controls to the desired setting by following the burn rate instructions below.

LOW

Burn Rate

Air Control

HIGH

Low (Closed)

Shown with Side

Shield Removed

High (Open)

Front Air Channel

Operated by Timer

Timer

NOTE: These are approximate settings, and will vary with type of wood or chimney draft. Due to altitude and other environmental circumstances, this operational information is a guideline only.

Start-Up Air

Control

Rear Air Channel

Operates independently from Timer

Timer Manual

Shut-off

2. High Burn Rate - Maximum Heat

Raise the Burn Rate Air Control all the way up until it stops

(top marker) to a fully open position. Slide the Start-Up Air

Control all the way back until it stops (HI marker) and leave it there. This setting over-rides the timer system (ACC) so you must monitor the fi re closely while in this setting.

REAR AIR

START-UP

HI

WARNING

Risk of Fire.

When set on High Burn Rate and over-riding the Automatic Combustion Control system an overfi re situation can occur and may result in a chimney fi re.

Overfi ring will void the stove warranty.

3. Medium-High Burn Rate

-

15,000 to 30,000 BTU/hr

Raise the Burn Rate Air Control all the way up until it stops (top marker) to a fully open position. Slide the

Start-Up Air Control all the way back until it stops (HI marker) and then pull forward until it stops. This activates the timer system (ACC).

September 1, 2010

Closed

Wide

Open

“HI” setting over-rides

Timer

After activating the timer (ACC), if the control is placed within the rear air section on the label it will allow rear air to enter the fi rebox. This will not interfere with the timer gradually closing the front air channel in 25 minutes. If control is set on “HI” it over-rides the timer (ACC).

F igure 27.1

NOTE: Operate appliance on High Burn 15 minutes a day to help keep fl ue/chimney clean.

7033-277H Page 27


G. Building A Fire

Before lighting your fi rst fi re in the stove:

1. Confi rm the baffl e is correctly positioned. It should be even with the front tube and resting on all tubes.

Figure

28.1.

2. Follow instructions on page 32 for cleaning plated surfaces, if applicable.

3. Remove all labels from glass.

There are many ways to build a fi re. The basic principle is to light easily-ignitable tinder or paper, which ignites the fast burning kindling, which in turn ignites the slow-burning fi rewood. Here is one method that works well:

1. Open the Burn Rate Air and Start-Up Air Controls fully.

2. Place several wads of crushed paper on the fi rebox fl oor.

Heating the fl ue with slightly crumpled newspaper before adding kindling keeps smoke to a minimum.

3. Lay small dry sticks of kindling on top of the paper.

4. Make sure that no matches or other combustibles are in the immediate area of the appliance. Be sure the room is adequately ventilated and the fl ue unobstructed.

5. Light the paper in the appliance. NEVER light or rekindle fi re with kerosene, gasoline, or charcoal lighter fl uid; the results can be fatal.

6. Once the kindling is burning quickly, add several fulllength logs 3 inches (76mm) or 4 inches (102mm) in diameter. Be careful not to smother the fi re. Stack the pieces of wood carefully; near enough to keep each other hot, but far enough away from each other to allow adequate air fl ow between them.

7. Set the Burn Rate Air Control and activate the timer system (ACC).

8. When ready to reload, It is best to fully open both the

Burn Rate Air and Start-up Air Controls before reloading . This livens up the coalbed and reduces excessive emissions (opacity/smoke). Open door slowly so that ash or smoke does not exit appliance through opening.

Large logs burn slowly, holding a fi re longer. Small logs burn fast and hot, giving quick heat.

9. As long as there are hot coals, repeating steps 6 through 8 will maintain a continuous fi re throughout the season.

NOTE:

• Do NOT use grates, andirons or other methods to support fuel.

It will adversely affect emissions.

Baffle Board even with front tube & resting on all tubes

Ceramic Blanket on Top

Burn Rate

Air Control

Start-Up

Air

Control

Tube Channels

2 pc Ba ffle Board

Figure 28.1

WARNING

Fire Risk

Do NOT store wood:

• Closer than required clearances to combustibles to appliance

• Within space required for loading or ash removal.

Do NOT operate appliance:

• With appliance door open.

• With ash removal system door open.

WARNING

Fire Risk.

• Do NOT burn wet or green wood.

• Store wood in dry location.

• Stack wood so both ends are exposed to air.

Wet, unseasoned wood can cause accumulation of creosote.

R


R

H. Correct Baffl e & Blanket Placement

WARNING

Fire Risk

Firebox damage due to improper baffl e placement is not covered by warranty. Operate the wood burning appliance with the baffl e in the correct position only.

Not doing so could result in:

• Overheating the chimney

• Overheating the rear of the fi rebox

Ensure correct baffl e placement and replace baffl e components if damaged or missing.

CAUTION

The baffl e boards are FRAGILE. Use extreme caution when loading fi rewood to prevent:

• Cracking, breaking or damaging the baffl e boards

DO NOT operate the stove without baffl e boards

CORRECT POSITION

Back of Firebox

Ceramic Blanket


INCORRECT POSITIONS

Ceramic Blanket and Baffl e Board are NOT in contact with the back of the fi rebox.

Ceramic Blanket is NOT in contact with the back of the fi rebox and NOT even with the Baffl e Board in the front.

Back of Firebox

Ceramic Blanket

Baffle Board

Ceramic Blanket and Baffl e Board MUST be in contact with the back of the fi rebox and even with each other in the front.

Figure 29.1

September 1, 2010

Baffle Board

Ceramic Blanket is bunched up at the back of the fi rebox and NOT even with the Baffl e Board in the front.

Figure 29.2

7033-277H Page 29

R


I. Blower Operating Instructions

NOTE: If your Quadra-Fire wood stove is equipped with an optional blower, you should follow these guidelines:

1. Initial (cold) start-up and all Burn Settings

The blower can be plugged in and turned on right away.

The blower fan is turned on and off by a snap disc.

When your stove has reached a certain temperature the blower will turn on and when your stove has cooled down to a certain temperature it will turn off.

NOTE: The blower can still be left on at all burn rates even if you have deactivated the snap disc with the manual over-ride knob. See page 15.

2. The blower is equipped with a speed control. Adjust the fan speed by turning the speed control clockwise to “Low” or counterclockwise to “High”.

3. Snap Disc Location

If you fi nd the blower coming on and off at undesirable temperatures, relocate the snap disc to another location in the designated zone on the back of the appliance.

Figure 30.1

There is a manual over-ride switch to deactivate the snap disc, if necessary. See page 15.

J. Opacity (Smoke)

This is the measure of how cleanly your appliance is burning. Opacity is measured in percent; 100% opacity is when an object is totally obscured by the smoke column from a chimney, and 0% opacity means that no smoke column can be seen. As you become familiar with your appliance, you should periodically check the opacity. This will allow you to know how to burn as nearly smoke-free as possible (goal of

0% opacity).

WARNING

Fire Risk.

• DO NOT BURN GARBAGE OR FLAMMABLE

FLUIDS SUCH AS GASOLINE, NAPTHA OR

ENGINE OIL.

• Do NOT burn treated wood or wood with salt (driftwood).

• May generate carbon monooxide if burn material other than wood.

May result in illness or possible death.

WARNING

Fire Risk.

Keep combustible materials, gasoline and other fl ammable vapors and liquids clear of appliance.

• Do NOT store fl ammable materials in the appliance’s vicinity.

• DO NOT USE GASOLINE, LANTERN FUEL,

KEROSENE, CHARCOAL LIGHTER FLUID OR

SIMILAR LIQUIDS TO START OR “FRESHEN UP” A

FIRE IN THIS HEATER.

• Keep all such liquids well away from the heater while it is in use.

• Combustible materials may ignite.

Figure 30.1

CAUTION

Odors and vapors released during initial operation.

• Curing of high temperature paint.

• Open windows for air circulation.

Odors may be irritating to sensitive individuals.

K. Frequently Asked Questions

ISSUES

Odor from appliance

Metallic noise

Whirring sound

Page 30

When fi rst operated, this appliance may release an odor for the fi rst several hours. This is caused by the curing of the paint and the burning off of any oils remaining from manufacturing.

Noise is caused by metal expanding and contracting as it heats up and cools down, similar to the sound produced by a furnace or heating duct. This noise does not affect the operation or longevity of the appliance.

If the optional blower has been installed, the blower produces a whirring sound which increases in volume as the speed is increased.

7033-277H

SOLUTIONS

September 1, 2010


R

9

Maintaining & Servicing Your Appliance

A. Quick Reference Maintenance Guide

BAFFLE & BLANKET PLACEMENT INSPECT FIREBRICKS & ASH COVER

(AFTER EACH CLEANING)

2

2

Step Top Models Only

Baffl e and blanket placement is critical to heat output, effi ciency and overall life of the unit. Make sure the baffl e is pushed all of the way to the back of the fi rebox and the blanket is laying fl at.

Firebrick is designed to protect your fi rebox. Replace fi rebricks that are crumbling, cracked or broken. If you have an optional ash door, check to make sure the door is closing properly.

CHIMNEY & CAP INSPECTION

The chimney and chimney cap must be inspected for soot and creosote during the burn season. This will prevent pipe blockage, poor draft, and chimney fi res.

Always burn dry wood to help prevent cap blockage and creosote build-up.

DOOR & LATCH CHECK

Keeping the door and glass gasket in good shape will maintain good burn times on a low burn setting.

Check the glass frame for loose screws to prevent air leakage.

Check the door latch for proper adjustment. This is very important especially after the door rope has formed to the stove face.

Start the fi rst inspection of your unit after the fi rst 2 months of use, or if performance changes, and adjust your schedule accordingly.

Maintenance is required for safe operation and must be performed to maintain your warranty.

These are generic drawings and may not represent your model.


R


B. General Maintenance

1. Creosote (Chimney) Cleaning

2. Ash Removal System (ARS) Operating and Cleaning

• By: Homeowner as recommended by a certifi ed chimney sweep; more frequently if chimney exceeds or is under 14-16 ft.

(measured from bottom of appliance)

• By: Certified Chimney Sweep

Remove all ash from the fi rebox and extinguish all hot embers before disposal. Allow the appliance to cool completely.

Disconnect fl ue pipe or remove baffl e and ceramic blanket from appliance before cleaning chimney. Otherwise residue can pile up on top of the baffl e and ceramic blanket and the appliance will not work properly. (See Baffl e Removal on page 36 ). Close the door tightly. The creosote or soot should be removed with a brush specifi cally designed for the type of chimney in use. Clean out fallen ashes from the fi rebox.

It is also recommended that before each heating season the entire system be professionally inspected, cleaned and repaired if necessary.

Inspection: Inspect the system at the appliance connection and at the chimney top. Cooler surfaces tend to build creosote deposits quicker, so it is important to check the chimney from the top as well as from the bottom.

Formation and Need For Removal : When wood is burned slowly, it produces tar and other organic vapors which combine with expelled moisture to form creosote.

The creosote vapors condense in the relatively cool chimney fl ue of a newly-started or a slow-burning fi re. As a result, creosote residue accumulates on the fl ue lining. When ignited, this creosote creates an extremely hot fi re which may damage the chimney or even destroy the house.

The chimney connector and chimney should be inspected once every 2 months during the heating season to determine if a creosote or soot buildup has occurred. If creosote or soot has accumulated, it should be removed to reduce the risk of a chimney fi re.

Injury Risk.

CAUTION

• May have sharp edges a. The stove and ashes must be completely cooled down before using the Ash Removal System. Reach down and locate the ash removal door handle under the left side of the stove in the center. Squeeze the handle and push all the way back. A magnet will hold the handle in place which in turn holds the ash door open.

b. Clean ash down through the ash removal system grate into the drawer below. If there are large pieces in the ashes, you can remove the grate before brushing the ash into the drawer.

Make sure all ash is removed from the top of ARS door.

Lift up the grate and inspect the top of the door to ensure all ash has been removed. You can rapidly move the ARS latch handle up and down to help remove any ash from the door. Use a small brush to clean off the top of the door if any ash remains.

Be sure to replace the grate before operating the stove.

Remember to leave 1/4 to 1/2 inch (6-13mm) of ash on the fi rebox fl oor to act as a natural grate, allowing air to fl ow freely underneath wood.

c. Close the door handle, you will hear a “click” when it closes.

The ash drawer will not pull out if the door handle is left in the open position. Wear gloves to remove the drawer.

Dispose of the ashes following the directions on page

32.

WARNING

Fire Risk.

Prevent creosote buildup.

• Inspect chimney connector and chimney once every two months during heating season.

• Remove creosote to reduce risk of chimney fi re.

• Ignited creosote is extremely HOT.

WARNING

Fire Risk

Injury Risk

Make sure Ash Removal System door is sealed tight against the gasket.

Air leakage may cause:

• Over-fi re condition.

• Flame and/or smoke spillage.

• Wood to burn too fast.

Page 32

WARNING

Fire Risk.

• Do not use chimney cleaners or fl ame colorants in your appliance.

Will corrode pipe.

7033-277H September 1, 2010

3. Disposal of Ashes

R


5. Glass Cleaning firebox lip

• By: Homeowner

Ashes should be placed in a metal container with a tight fi tting lid. The closed container of ashes should be placed on a non-combustible fl oor or on the ground, well away from all combustible materials, pending fi nal disposal. If the ashes are disposed of by burial in soil or otherwise locally dispersed, they should be retained in the closed container until all cinders have thoroughly cooled.

WARNING

Fire Risk.

Disposal of Ashes

• Ashes should be placed in metal container with tight fi tting lid.

• Do not place metal container on combustible surface.

• Ashes should be retained in closed container until all cinders have thoroughly cooled.

• By: Homeowner

Clean glass with a non-abrasive glass cleaner. Abrasive cleaners may scratch and cause glass to crack. If the deposits on the glass are not very heavy, normal glass cleaners work well. Heavier deposits may be removed by using a damp cloth dipped in wood ashes or by using a commercially available oven cleaner.

After using an oven cleaner, it is advisable to remove any residue with a glass cleaner or soap and water. Oven cleaner left on during the next fi ring can permanently stain the glass and damage the fi nish on plated metal surfaces.

A portion of the combustion air entering the firebox is defl ected down over the inside of the door glass. This air fl ow “washes” the glass, helping to keep smoke from adhering to its surface.

When operated at a low burn rate, less air will be fl owing over the glass and the smokey, relatively cool condition of a low fi re will cause the glass to become coated.

Operating the appliance with the Burn Rate Air Control and

Start-Up Air Control all the way open for 15-20 minutes should remove the built up coating.

4. Cleaning Plated Surfaces

• By: Homeowner

Clean all the fi ngerprints and oils from plated surfaces

BEFORE fi ring the appliance for the fi rst time. If not cleaned properly before lighting your fi rst fi re, the oils can cause permanent markings on the plating.

After the plating is cured, the oils will not affect the fi nish and little maintenance is required. Wipe clean as needed.

CAUTION

• Do not use polishes with abrasives.

It will scratch plated surfaces.

CAUTION

Glass

Assembly

Handle glass assembly with care.

When cleaning glass:

• Avoid striking, scratching or slamming glass.

• Do NOT clean glass when hot.

• Do NOT use abrasive cleaners.

• Use a hard water deposit glass cleaner on white fi lm.

• Use commerical oven cleaner on heavier deposits.

• Remove all residue of oven cleaner or will permanently stain glass on next fi ring.

•

Refer to maintenance instructions.


R


C. Glass Replacement

1. Ensure that the fi re is out and the appliance is cool to the touch.

2. Protect a table or counter top with padding or towels.

Protect your hands and wear gloves to prevent injury.

3. Remove the door with the broken glass by lifting the door up and off of the hinges.

4. Lay door face down on a table or counter making sure the handle hangs over the edge so the door lays fl at, on a soft surface.

5. Remove the screws from each glass retainer and remove the glass. (If screws are diffi cult to remove, soak with penetrating oil fi rst).

6. Center the glass with edges evenly overlapping the opening in the door, (i.e. same space top and bottom, left and right sides).

7. Replace the glass retainers. Be careful not to cross thread the screws.

8. Tighten each retainer just a few turns until each is secured. Check again for centering of glass in door frame. Continue to tighten each retainer alternately, a few turns at a time, until the glass is secure. DO

NOT OVERTIGHTEN.

9. Replace the door on the appliance.

Quadra-Fire stoves are equipped with ceramic super heat-resistant glass, which can only be broken by impact or misuse. Do not slam stove door or impact the glass.

When closing door, make sure that logs do not protrude against the glass. Inspect glass regularly. If you fi nd a crack or break, immediately put the fi re out and return the door to your dealer for replacement of glass before further use.

WARNING

Handle glass with care.

Glass

Assembly

• Inspect the gasket to ensure it is undamaged.

• Do NOT strike, slam or scratch glass.

• Do NOT operate appliance with glass

& door assembly removed.

• Do NOT operate with glass cracked, broken or scratched.

Page 34

WARNING

Fire Risk.

Injury Risk.

• Use only glass specifi ed in manual.

• DO NOT REPLACE with any other material.

Glass breakage will occur.

7033-277H September 1, 2010

R

D. Firebrick Replacement

Replace the fi rebrick if they become crumbly and/or if there is a 1/4 inch (6.35mm) gap between the bricks.

Inspect the fi rebrick after each ash removal.

The fi rebox is lined with high quality fi rebrick, which has exceptional insulating properties. There is no need to use a grate; simply build a fi re on the fi rebox fl oor. Do not operate appliance without fi rebrick.

1. After the coals have completely cooled, remove all old brick and ash from unit and vacuum fi rebox.

2. Remove new brick set from box and lay out to diagram shown.

3. Lay bottom bricks in unit.

4. Install rear bricks on the top of the bottom bricks. Slide top of bricks under clip on back of fi rebox wall and push bottom of brick back.

5. Install side bricks. Slide top of brick under clips on side of fi rebox and push the bottom of the brick until it is fl ush with the side of the appliance.

1

4

1

1

1

2

1

1

2

1

1

1

2 2

3

1

1

1

1-1/4 in.

9 in.

3

1-1

1-1/4 in.

2 in.

5 in.

8 in.

4

2 in.

3 in.

Figure 35.1 - 3100 Millennium Brick Assembly

No.

1

2

3

4

Brick Size

9 x 4-1/2 x 1-1/4

6 x 4-1/2

9 x 4-1/2 with angle (see drawing)

9 x 3 with angle (see drawing)

Qty

12

4

1

1

September 1, 2010 7033-277H


1 1

5

1

1

1

2

4

1

No brick, ARS

Grate Location

1

4

2

2 2

1-1/4 in.

9 in.

3

2 in.

5 in.

2 in.

1-1

8 in.

5 3 in.

1-1/4 in.

3

1

1

1

Figure 35.2 - 3100 Step Top Brick Assembly

3

4

5

No.

1

2

Brick Size

9 x 4-1/2 x 1-1/4

6 x 4-1/2

9 x 4-1/2 with angle (see drawing)

4-1/2 x 4-1/2 x 1-1/4

9 x 3 with angle (see drawing)

1

2

1

Qty

10

4

Use Part 832-0550 when ordering individual brick. Provide brick dimension or copy this page, mark the desired brick and take it to your authorized dealer.

NOTE: The Ash Removal System is available for the Step Top Model only and not for the Millennium Model.

Page 35

R


E. Baffl e Removal E. Snap Disc Replacement

1. Remove all ash from the fi rebox, and extinguish all hot embers before disposal into a metal container.

1. Locate the snap disc bracket assembly at the bottom left rear corner of the stove. Figure 36. 3

2. The baffl e board has 2 pieces. With the ceramic blanket still in place, slide one baffl e piece over the top of other one and pull out top piece through the door opening and then remove bottom baffl e piece. Figure 36.1

2. A magnet holds the bracket to the stove. Pull the bracket down away from the stove to expose the snap disc.

3. Pull the snap disc and spade connectors up and out of bracket as shown in Figure 36.4.

3. Remove the ceramic blanket.

4. Re-install the baffl e pieces one piece at a time. Be sure the baffl e boards are even with the front manifold tube and is resting on all tubes. See page 29.

4. Using a Phillips head screw driver, remove the 2 screws from the snap disc and then remove the snap disc from the spade connectors. Replace with new snap disc and re-connect to spade connectors.

5. To re-install the ceramic blanket, it is easier to fold it in half fi rst. Place on top of baffl e board, open up and fl atten and smooth out the blanket. Re-check the baffl e board for correct positioning. Figure 36.2.

5. Push the snap disc and spade connectors back inside bracket and re-attach the bracket to the stove.

Figure 36.1

- Baffl e

Snap Disc Location

Figure 36.3

Snap Disc

Figure 36.2 - Ceramic Blanket

Page 36

Figure 36.4

7033-277H

Magnet

Spade

Connectors

September 1, 2010

R


G. Tube Channel Assembly Replacement

Removing Tube Channel Assembly

1. Remove the right side shield by removing 2 screws in the back using a Phillips head screw driver.

2. Remove 4 screws from channel access cover and remove cover.

3. Locate 2 channel nuts inside of chamber and remove using a 7/16 socket wrench. Slide out tube channel assembly.

NOTE : Soak the bolts with penetrating oil for at least 15 minutes before trying to remove them.

Replacing Tube Channel Assembly

1. Slide one gasket onto each tube.

2. Slide the tube channel assembly into side of fi rebox and insert each tube into the corresponding hole in the tube channel rack starting with the back hole fi rst.

3. Make sure tube channel assembly is fl ush against the side of the stove and secure with channel nuts.

4. Re-install channel cover and side shield.


In order to replace the tube channel assembly a clearance of 19 inches (483mm) is required on the right side of stove in order to remove the tubes with the stove in place.

If space is not available, the stove will have to be disconnected from the chimney to proceed with the tube replacement.

Tube Channel Rack

Slide one gasket over each tube

Channel

Access

Cover

Channel Cover

Screws (4)

Channel

Nuts (2)

Tube Channel

Assembly

Side Panel

Remove

2 Screws

Figure 37.1



10

Troubleshooting

Start Fire Problems

With proper installation, operation, and maintenance your woodstove will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a qualifi ed service person in the diagnosis of a problem and the corrective action to be taken.

Possible Cause Solution

Can’t get fi re started

Excessive smoke or spillage

Burns too slowly

Smolders, sizzles

Fire burns too fast

Not enough kindling/paper or no kindling/paper

Not enough air for fi re to ignite

Wood condition is too wet, too large

Bed of coals not established before adding wood

Flue blockage such as birds’ nests or leaves in termination cap

Down draft or negative pressure

Competition with exhaust devices

Extremely dry or soft wood

Overdrafting

ARS door may not be closed completely

Ash left on ARS door

Use dry kindling, more paper. Arrange kindling & wood for air movement.

Check for restricted cap/shroud

Open outside air kit (if installed).

Check for fl ue blockage.

Pre-warm fl ue before starting fi re (refer to starting fi re section).

Check for adequate vent height (refer to chimney assembly section).

Open window below the appliance towards the wind.

Use dry, seasoned wood (refer to wood fuel section).

Start with paper & kindling to establish bed of coals (refer to starting fi re section).

Have chimney inspected for creosote and cleaned by a certifi ed chimney sweep.

Do not use exhaust fans during start-up (refer to negative pressure section).

Open window below the appliance towards the wind.

Mix in hardwood.

Mix in less seasoned wood after fi re is established

(refer to wood fuel section).

Check for correct vent height; too much vertical height creates overdrafting.

Check location of vent termination (refer to chimney requirements section).

Handle set screw rotated on ash door rod - Follow installation instructions

No seal is created. Clean off top of ARS door for complete seal.

R


www.quadrafire.com

A. Exploded Drawings

R

Service Parts

31M-ACC-MBK

31ST-ACC

1

3100 Series ACC

Beginning Mfg Date: 07-19-06

Ending Mfg Date:

24

25

2

SEE FIG. A

4

3

5

6

Figure 39.1

September 1, 2010

13

12

7

8

7033-277H

9

10

11

7025-020B 6-29-09

Page 39

www.quadrafire.com

R

Service Parts

31M-ACC-MBK

31ST-ACC

27

26

3100 Series ACC

Beginning Mfg Date: 07-19-06

Ending Mfg Date:

35

14

22

23

15

16

17

18

19

FIGURE A

20

21

28

FIGURE B

29

30

31

32

33

34

36

37

39

FIGURE C

38

MILLENNIUM

42

43

41

38

40

FIGURE D

STEP TOP UNIBODY FIGURE E

Part number list on following page.

7025 020B June 29 2009 Page 2 of 7

Page 40 7033-277H

STEP TOP UNIBODY

September 1, 2010

R

Service Parts

3100 Series ACC

IMPORTANT: THIS IS DATED INFORMATION

When requesting service or replacement parts for your appliance please provide model number and serial number. All parts listed may be orderd from an authorized dealer .

Item

1

2

10

15

16

17

21

22

23

18

19

20

24

25

5

6

3

4

7

8

9

11

12

13

14

26

27

Brick Retainer

Baffle Board

Ars Grate

Description

Panel Assembly, Side, Left

Firebrick Set

Brick, Single

Brick, Uncut, Set Of 6

Tube Support Rack

Ceramic Fiber Blanket, 1/2 “ Thick

Rear Channel Assembly

Label, Burn Rate

Panel Assembly, Side, Right

Label, Start-Up, Acc

Tube Channel Top

Tube, Channel Assembly

Burn Rate Control Assembly

Spring Handle, 1/4”

Door Gasket

Timer Air Control Assembly

Door Gasket

Rear Air Door Assembly

Rear Air Control Arm Assembly

Knob

Air Control Rod Guide

Latch, Magnet

Timer Arm Assembly

Timer (Only) Replacement Assembly

Air Channel, Convection W/Bracket

Air Supply Back

Door Assembly

Hinge Pins, 1/2”

Millennium

Step-Top

Millennium

Step-Top

Qty: 1

Qty: 6

HOW TO ORDER

To order the entire assembly, order the top line part number only.

To order an individual part from an assembly, order the part(s) listed in the indented portion.

Stocked at Depot

For Air Control

Comments

19 in. W x 13-3/4 in H

Qty: 2, 9-1/2 in W x 13-3/4 in H

Step-Top

Millennium

Step-Top

Tube Channel Access Cover

Manifold Tubes

Gold

Nickel

Front & Rear Air Timer Doors

Front & Rear Air Timer Doors

Start-Up Control Knob

Retain Original Serial Number Label

Black

Gold Trim

Nickel Trim

Qty: 2 Gold

Qty: 2 Nickel

Part Number

7033-019

7033-038

SRV7033-006

SRV7033-032

832-0550

832-3040

7033-148

7033-149

832-3390

SRV7033-209

7033-002

7033-173

7033-160

7033-017

7033-037

7033-166

SRV7033-237

SRV7033-023

7033-033

832-0630

250-8340

7033-282

SRV7033-052

7033-282

7033-024

7033-035

7000-343

7033-210

229-0631

7033-034

SRV480-1940

SRV7033-144

SRV7033-134

832-1092

832-1912

DR-31/43NL

832-0250

430-5320

Y

Y

Y

Y

Y

Y

Y

Y

Y

Y

Y

Y

Y

Y

Y

Y


30

31

32

33

34

35

HOW TO ORDER

36

37

38

39

Item

28

29

40

41

42

43

R

Service Parts

3100 Series ACC




Description

Door Handle Only

Comments


Trim, Ring, Door

Gold

Nickel

Gold Trim

Nickel Trim

15.63 W x 11.50 H

Qty; 4 pc

Door Glass Assembly

Glass Frame Set

Cam Latch

Key, Cam Latch

Nut, Locking Door Handle

Gasket, Glass Tape, 3/4 “

Rope, Door, 3/4” X 84”

Screw, Flat Head Philips 8-32X1/2

Washer, Sae, 3/8 (3 Ea)

Pedestal Riser

Pedestal Base

Strip, Oak Trim

Ash Pan, Front Assembly Leg

Ash Pan Leg Ars

Legs, Queen Anne

Leg Mount Bracket

Pedestal Assembly

Ashpan Assembly

Ash Pan Door Handle

Ars, Door Assembly

Ashpan Assembly

Blower Control Box W/Switch

Blower, Convection

Channel, Ash Removal

Component Pack (Includes Gold Spring

Handles (1) 1/2 Inch & (2) 1/4 Inch, (2) Gold

Hinge Pins, Quadra-Fire Logo

Hinge Pins, 1/2”

Logo, Quadra-Fire



Qty: 24

Qty: 5 Ft, Field Cut to Size

Qty: 7 Ft, Field Cut to Size

Qty: 10

Qty: 3

Millennium

Millennium

Qty: 2

Step-Top

Step-Top

Black

Gold

Nickel

Step-Top (Set)

Step-Top

Step-Top

Step-Top

Step-Top

Step-Top

Replacement Blower

Step-Top

For Black & Gold Trim Doors

Qty: 2, Gold

Gold

Qty: 1, Gold

Qty: 2, Gold

7033-207

7033-163

832-0560

7033-008

7033-050

831-1240

831-1250

LEGS-QANL

SRV7033-183

7033-013

7033-010

7033-274

SRV7033-015

7033-010

SRV7000-194

812-4900

7033-172

Part Number

430-1131

832-0620

250-8330

430-2682

430-5340

7000-012

832-0350

430-1141

430-1151

226-0100/24

832-0460

832-1680

832-0860

832-0990

436-5350

832-0250

200-3180

832-0620

832-0630

Y

Y

Y

Y

Y

Y

Y

Y

Y

Y

Y


HOW TO ORDER

Item

R

Service Parts

3100 Series ACC




Description

Component Pack (Includes Nickel Spring

Handles (1) 1/2 Inch & (2) 1/4 Inch, (2)

Nickel Hinge Pins, Quadra-Fire Logo)

Hinge Pins, 1/2”

Logo, Quadra-Fire



Component Pack (Includes Touch-Up Paint,

Owners Manual & Warranty Card)

Paint Touch-Up

Component Pack Assembly ( Includes

Touch-Up Paint, Nickel Spring Handles

(1) 1/2 Inch & (2) 1/4 Inch, Trimount Plug,


Paint Touch-Up

Plug, Trimount, .250”



Component Pack Assembly (Includes

Touch-Up Paint, Gold Spring Handles (1)

1/2 Inch & (2) 1/4 Inch, Trimount Plug,


Paint Touch-Up




Door Handle Assembly

Flue Collar

Gasket, Ars

Latch, Handle Assembly, Ash Removal

Magnet Round

Outside Air Collar Assembly

Outside Air Cover Plate Assembly

Outside Air Shield

Snap Disc Bracket Assembly

Snap Disc, # 1, Convection Blower

Upgrade, Door, Nickel

Wire Harness (Blower)

Qty: 24

Qty: 1

Qty: 1

Qty: 24

Qty: 1

Qty: 2

Millennium

Step-Top

Comments

For Nickel Trim Doors

Qty: 2, Nickel

Nickel

Qty: 1, Nickel

Qty: 1, Nickel

Step Top, Spring Handles Included in Door

Assembly

For Nickel Trim (Stoves)

For Black & Gold Trim (Stoves)

Nickel Spring Handles, Hinge Pins & Logo

Part Number

436-5360

430-5320

200-3240

250-8330

250-8340

7033-043

7000-304

7033-029

7000-304

229-0880/24

250-8330

250-8340

7033-027

7000-304

229-0880/24

832-0620

832-0630

832-0540

SRV7000-302

SRV7033-296

SRV7033-047

SRV7000-140

7033-039

SRV7033-041

33271

7033-036

SRV230-0470

UK-DRNL

7033-262

Y

Y

Y

Y

Y

Y

Y

Y

Y

Y

Y

Y

Y

Y

Y


HOW TO ORDER

Item

R

Service Parts

3100 Series ACC




Description Comments

ACCESSORIES

Blower Assembly

Blower Control Box W/Switch

Component Pack

Snap Disc Bracket Assembly

Snap Disc, # 1, Convection Blower

Wire Harness (Blower)

Leg Kit & Ash Removal System

Ash Pan Leg Ars

Ars, Door Assembly

Ash Pan, Front Assembly Leg

Component Pack, Leg Step Top (Includes

Gasket For Ash Removal, Magnet &

Fasteners)

Gasket, Ars


Magnet Round

Black

Gold

Nickel

Step-Top

Step-Top

Step-Top

For Leg Step-Top

Step-Top

Legs, Queen Anne

Black

Gold

Nickel

Outside Air Kit, Floor & Rear

Outside Air Collar Assembly

Outside Air Shield

Pedestal

Ars, Door Assembly

Ash Pan Door Handle

Ashpan Assembly

Component Pack, Pedestal, Step-Top

(Includes Gasket For Ash Removal,

Magnet & Fasteners)

Gasket, Ars


Magnet Round

Outside Air Cover Plate Assembly

Pedestal Assembly

Strip, Oak Trim

Step-Top

Step-Top

Pedestal, Step-Top

Step-Top

Step-Top

Part Number

SRV7033-296

SRV7033-047

SRV7000-140

831-1240

831-1250

LEGS-QANL

OAK-ACC

7033-039

33271

PED-3143

SRV7033-015

7033-274

7033-010

BK-ACC

SRV7000-194

SRV7033-051

7033-036

SRV230-0470

7033-262

LEG-3143-BK

LEG-3143-GD

LEG-3143-NL

7033-050

SRV7033-015

7033-008

7033-048

7033-045

SRV7033-296

SRV7033-047

SRV7000-140

SRV7033-041

7033-013

832-0560

Y

Y

Y

Y

Y

Y

Y

Y

Y

Y

Y

Y


HOW TO ORDER

Item

R

Service Parts

3100 Series ACC




Description

Avk Rivnut Repair Kit

Bolt, Hex Head, 1/4-20 X 1

Button Head 1/4-20 X .5

Nut, Keps Lock, 10-32

Nut, Keps Lock, 8-32

Nut, Locking Door Handle

Nut, Ser Flange Small 1/4-20


Screw, Flat Head Philips 8-32X1/2

Screw, Sheet Metal #8 X 1/2 S-Grip

Washer, 1/4 Sae

Washer, Sae, 3/8 (3 Ea)

Comments

FASTENERS

1/4-20 & 3/8-16 Rivnut Tools

Qty: 10

Qty: 20

Qty: 40

Qty: 40

Qty: 24

Qty: 24

Qty: 24

Qty: 10

Qty: 40

Qty: 24

Qty: 3

Part Number

RIVNUT-REPAIR

25221A/10

32328/20

226-0050/40

226-0060/40

226-0100/24

226-0130/24

229-0880/24

832-0860

12460/40

28758/24

832-0990

Y

Y

Y

Y

Y

Y

Y

Y

Y

Y



C. Warranty Policy

R


R



R

CONTACT INFORMATION:

Hearth & Home Technologies

1445 North Highway

Colville, WA 99114

Division of HNI INDUSTRIES

Please contact your Quadra-Fire dealer with any questions or concerns.

For the number of your nearest Quadra-Fire dealer, log onto www.quadrafi re.com

CAUTION

• Important operating a n d m a i n t e n a n c e instructions included.

DO NOT DISCARD THIS MANUAL

• Read, understand and follow these instructions for safe installation and operation.

• Leave this manual with party responsible for use and operation.

DO NOT

DISCARD

We recommend that you record the following pertinent information for your 3100 WOOD STOVE (ACC)

Date purchased/installed:

Serial Number:

Dealership purchased from:

Notes:

Location on appliance:

Dealer phone:

This product may be covered by one or more of the following patents: (United States) 5341794, 5263471, 6688302, 7216645,

7047962 or other U.S. and foreign patents pending.


No results