advertisement
GW312/315
Ethernet Serial Server
Quick Start Guide
Version 1.4
Updated on April, 2017
Toll Free: 1-888-908-3330
Tel: 1-732-568-1988 www.neteon.net
Quick Start Guide Version 1.4
Ethernet Serial Server
GW312/315
This document intends to provide customers with brief descriptions about the product and to assist customers to get started. For detail information and operations of the product, refer to the product user’s manual in the product CD.
1. Packaging
Check your package contains the following items:
GW312/315 Serial-Ethernet Server
GW312 or GW315 Ethernet Serial Device Server x 1
5 pins Terminal Block for Serial Connector x 1 (only for GW315)
3 pins Terminal Block for Power Connector x 1 (only for GW315)
Wall-mounting screws x 2
Serial Server quick start guide x 1
Product CD containing configuration utility x 1
Power Adapter - DC Jack 12VDC,1.25A with Lock
Optional Accessories ：
- Din Rail Kit DK-25
NOTE:
1. GW312 (for RS-232/422/485 without isolation ), GW315 (for RS422/485 with isolation)
2. Press reset button of GW312/315 to reset to the default value, shows the interface as below.
Fig 1. GW312/315 Interfaces
Copyright © 2017 Neteon Technologies, Inc.
All rights reserved. Designed in Taiwan.
1
Quick Start Guide Version 1.4
Ethernet Serial Server
GW312/315
LED Indicators:
Message
Off
Blinking with Green
Blinking with Orange
Message
Off
Com 1(2)TX Blinking
Com 1(2)RX Blinking
Fig. 1 LAN LED
Description
Ethernet Disconnected
Data transmitting on Ethernet at 100Mbps
Data transmitting on Ethernet at 10Mbps
Table 1. LAN LED Message
Fig. 1.
Fig. 2 COM Port LED
Description
No data transmitting on COM port
Data transmitting on COM port
Data Receiving on COM port
Table 2. COM Port LED Message
Fig. 2.
Fig. 3RUN LED
Message Description
On
Blinking (rate: 0.5 Sec)
Jumper JP1 Pin1 and Pin2 are shorted to disable AP firmware
AP firmware running normally
Table 3. RUN LED Message
Fig. 3.
Installation Procedures:
Step 1 : Connect GW312/315 to power source
Step 2 : Connect GW312-315 to the Ethernet network. Use a standard straight-through Ethernet cable when connect to a hub/switch, or connect to a PC‘s Ethernet port via a cross-over Ethernet cable. However,
Always make sure your PC is on the same network sub-net as GW312/315.
Step 3 : Connect GW312/315 serial port to a serial device.
Step 4 : Mount GW312/315 to a wall/panel with the screws included or Din-Rail rack (Require optional item model: Din-Rail-Kit).
Default Network Setting: Default User Name/Password:
IP: 10.0.50.100 User Name: admin
Gateway: 10.0.0.254 Password: default
Subnet: 255.255.0.0
Auto IP (Dynamic IP):
A DHCP server can automatically assigns the IP address and all the network settings. GW312/315 supports the DHCP client function. By default, the DHCP client function on GW312/315 is disabled; you may activate the DHCP client functions by executing SerialManager (Fig. 4)
Fig. 4. SerialManager utility Dialog Window
Copyright © 2017 Neteon Technologies, Inc.
All rights reserved. Designed in Taiwan.
2
Quick Start Guide Version 1.4
Ethernet Serial Server
GW312/315
Assign a Static IP address by:
A Configuration Telnet
1. Telnet to GW312/315 using DOS command “ Telnet IP_address ”. Example: telnet 10.0.50.100
2.
GW312/315’s network, link mode and COM ports settings can be configured in the telnet window
B Configuration by SerialManager Utility
Use SerialManager on Product CD to configure the GW312/315.First click” Configuration ” then assign a static IP.
C. Configuration by Web Browser
1. Make sure the PC is on the same network as GW312/315
2. Open a web browser, then Enter in the IP address as the GW312/315. The default user name is admin and default password is default .
3. The GW312/315’s network, link mode and COM ports settings can be configured on different web pages.
4. Click ” to save settings.
5. Click ” button to initiate the change.
The pin assignments of DB9 connector on GW312 is shown in the following table:
Pin#
RS-232
Full Duplex for GW312 Model for
RS-485
2 wire, Half Duplex
GW312 Model
N/A
RS-485/RS-422
4 wire, Full Duplex for GW312 Model
N/A
TXD+
DATA+
N/A
RXD +
N/A
5 SG (Signal Ground) SG (Signal Ground)
N/A
SG (Signal Ground)
N/A
DATA-
N/A(reserved)
N/A
RXD-
TXD-
N/A
The pin assignments of Terminal Block connector on GW315 is shown in the following table:
Pin#
RS-485/RS-422
4 wire, Half Duplex
For GW315
RS-485
2 wire, Full Duplex
For GW315
5 SG (Signal Ground) SG (Signal Ground)
Customer Services and Supports
Telephone : Toll Free 1-888-908-3330, Outside USA: +1-732-568-1988
Email: [email protected]
Web: www.neteon.net
Copyright © 2017 Neteon Technologies, Inc.
All rights reserved. Designed in Taiwan.
3
advertisement
Related manuals
advertisement