MODELS:

EL1500CWS, ET1500CWS

1.1

Ethernet over Coax

2.5

4.0

1.6

NITEK Model: ET1500C

NITEK

Made in USA

Transmitter

9.92

8.74

Top (Side View)

Bottom (Side View)

EL1500CW, ET1500CW,

NITEK Model: IPCOAX1

5.1

.9

1.8

EL1500CWS

2.17

8.25

NITEK Model: ET1500CWS

5.74

4.56

Outdoor Rated Ethernet

& PoE Extender

08132013

Description

Four models EL1500CW, ET1500CW, EL1500CWS, and

ET1500CWS are part of the EtherStretch solution allowing for outdoor installation. The models listed in the Nitek catalog with a “W” are intended for outdoor applications. The “ET” models are shipped with just the NEMA Enclosure and an

ET1500C EtherStretch transmitter. The “EL” models are shipped with both the ET1500C transmitter and the ER1500C receiver EtherStretch units. The “S” incorporates the

IPCOAX1 surge protector.

The WP1325 is a polycarbonate and high-impact ABS molded enclosures meet NEMA 4X specifications and are ideal for use when installing Nitek products outdoors. The units is equipped with a neoprene gasket to prevent Ingress of moisture and dust. The cable entries into the box are made through the UL94V-2 rated nylon hex nut cable seal which is required to maintain NEMA 4X ratings when cables enter or exit a NEMA 4 or 4X type enclosure. The WP1325 is often ordered as a “W” option with other Nitek products.

The ET1500CW contains a transmitter constructed of industrial grade RoHS compliant plated corrosion resistant aluminum finish. It works with any of the EtherStretch multiport systems, as-well-as the single port receiver ER1500C.

Our EtherStretch solution allows for the utilization of existing cable infrastructure (coax or UTP) to transmit data from IP cameras and other network devices along with power (PoE) to operate these networked devices well beyond standard network limitations. The system can extend Ethernet to over

500m or 1600ft of coaxial cable making the ET/EL1500CW ideal for retrofitting existing installations.

The unit requires very little installation time and no set up or configuration. The ET1500CW is transparent to the network thus requiring no IP and MAC addressing. Simply connect your network devices to the networking ports of the transmitter and receiver along with existing cabling and the system begins communicating. LED indicators show the status of network communication and PoE power. The

ET1500CW requires no network settings to be changed or adjusted.

The IPCOAX1 is a single channel, in-line, Ethernet over

COAX surge protector for IP cameras. In addition it provides independent protection for 12 or 24 volt power, which can be used with heaters, blowers or PTZ. The unit has standard female BNC connectors for connection to coaxial cables and is ideal for small or restricted spaces.

The IPCOAX1 provides a heavy duty, single point ground connection and is easy to install in minutes.

NITEK Model: ET1500CW

RoHS

COMPLIANT

2002/95/EC

NITEK

®

IEC/UL 60950-1

5410 Newport Drive, # 24

Rolling Meadows, IL 60008

Phone: (847) 259-8900

Fax: (847) 259-1300

E-mail: [email protected]

WWW.NITEK.NET

De Schans 19-21 2a

8231 KA Lelystad

Tel: +31(0)320-230005

E-mail: [email protected]

WWW.NITEK.NL

Features

EL1500CW & ET1500CW

●

Supports 10/100 and PoE over RG59 cables up to distances of 500 meters (1600 feet)

●

Transmitter housed in a NEMA 4X rated enclosure for outdoor applications  

●

Fully transparent to the network  

●

Supports any network device, including mega-pixel technology IP cameras

●

Easy to install, no set up required

●

No MAC or IP addressing required  

●

LED indicators for network signals, link status and power  

●

Ground loop isolation

●

UL Listed IEC/UL 60950-1

●

Designed to IP 65 of IEC 529 and NEMA 1, 2, 4, 4x, 12, and 13 Specifications

●

Cover attaching screws are outside the sealing area, preventing ingress of moisture and dust

●

Cover screws are M-4 Stainless Steel, Non-Magnetic and Fasten into threaded Brass Inserts

Technical Specifications

Network Transmission Device & Enclosure

RJ45 Connector Network Port

Link Port

Ethernet

Dimensions:

Transmitter

BNC Coax Jack

100BASE-TX Full Duplex

5.1” x 1.6” x 1.1” including tabs &

Enclosure

Internal Volume:

9.92” x 5.74” X 2.17”

Operating Temperature:

ET1500C

Enclosure

-15° to 75° C / 0° to 167° F

-40° to 120° C / -40° to 248° F

Rating/Listing

529, NEMA 1, 2, 4, 4x, 12, 13

Shipping Dimensions

Shipping Weight

10” x 6” x 3”

4 lbs

IPCOAX1 Surge Protection for use in the ET/EL1500CWS

●

Heavy duty single point ground

●

1 picosecond clamping time

●

Lifetime warranty

●

Separate power protection for 12 or 24 VAC

●

Will pass PoE+ power

Available PoE Wattage At PoE Device

26.3

25.0

22.2

20.0 18.4

15.0

15.0

15.4

12.7

10.0

15.4

12.2

9.6

5.0

8.2

0.0

802.3AT

802.3AF

100 Meters

328 Feet

26.3 Watts

15.4 Watts

200 Meters

650 Feet

22.2 Watts

15.4 Watts

300 Meters

1,000 Feet

18.4 Watts

12.2 Watts

400 Meters

1,300 Feet

15.0 Watts

9.6 Watts

500 Meters

1,640 Feet

12.7 Watts

8.2 Watts

* Results charted were calculated using RG59U coaxial cable with a 20AWG center conductor and power sourcing equipment using IEEE 802.3AF standard with starting voltage of 48 volts DC and IEEE 802.3AT standard with starting voltage of 54 volts DC. PoE Switches with internal power and current limits may change individual results.

Ethernet over COAX

Connection Power

Standard female BNC

Push-in terminals - rate @ 5

Amps

Clamping

12/24VAC/DC

Data/PoE+ Ethernet

30 Vrms

58 Vp-p

1 picosecond typ. Transient Response Time

Peak Pulse Power Dissipation

Impedance

Operating Temperature

3,000 W/pair (10/100us)

50 or 75 Ohms

-40° to 85° C / -40° to 185° F

Dimensions

Shipping Weight

2.5” x 1.8” x 0.9”

1 lb