axing basic-line Series Operation Instructions
Add to my manuals
4 Pages
Axing basic-line Series multiswitches are designed to amplify and distribute radio and TV signals within a household. They feature multiple inputs for connecting satellite and terrestrial antennas, and multiple outputs for connecting to TV outlets. The multiswitches support DiSEqC 1.0 switching commands, allowing you to control satellite receivers and select channels remotely. With built-in LNB power supply, they can power connected satellite dishes. These multiswitches are suitable for both residential and commercial use, providing a reliable and efficient signal distribution solution.
advertisement
Sicherheitshinweise: Die Installation des Geräts und Reparaturen am Gerät sind ausschließlich vom Fachmann unter Beachtung der geltenden Richtlinien durchzuführen. Bei nicht fachgerechter Installation und Inbetriebnahme wird keine Haftung übernommen. Vor der Handhabung ist der Netzstecker zu ziehen bzw. die Stromzuführung zu entfernen, andernfalls besteht Lebensgefahr. Dies gilt auch, wenn Sie das Gerät reinigen oder an den Anschlüssen arbeiten. Sofern eine austauschbare Sicherung vorhanden ist, ist vor dem Wechsel der Sicherung der Netzstecker zu ziehen. Defekte Sicherungen nur durch normgerechte Sicherungen des gleichen Nennwertes ersetzen. Das Gerät darf nur in trockenen Räumen betrieben werden. In feuchten Räumen oder im Freien besteht die Gefahr von Kurzschlüssen (Achtung: Brandgefahr) oder elektrischem Schlägen (Achtung: Lebensgefahr). Um Beschädigungen am Gerät selbst oder an Peripheriegeräten vorzubeugen, dürfen Geräte, die zur Wandmontage vorgesehen sind nur auf flachen Oberflächen montiert werden. Planen Sie den Montage- bzw. Aufstellort so, dass in Gefahrensituationen das Gerät vom Strom getrennt werden kann. Wählen Sie den Montage- bzw. Aufstellort so, dass Kinder nicht unbeaufsichtigt am Gerät und dessen Anschlüssen spielen können. Der Montage- bzw. Aufstellort muss eine sichere Verlegung aller angeschlossenen Kabel ermöglichen. Wählen Sie einen Montage- bzw. Aufstellungsort, an dem unter keinen Umständen Flüssigkeiten oder Gegenstände in das Gerät gelangen können (z. B. Kondenswasser, Dachundichtigkeiten, Gießwasser etc.) Setzen Sie das Gerät niemals direkter Sonneneinstrahlung aus und vermeiden Sie die direkte Nähe von Wärrmequellen (z. B. Heizkörper, andere Elektrogeräte, Kamin etc.) Bei Geräten, die Kühlkörper oder Lüftungsschlitze haben, muss daher unbedingt darauf geachtet werden, dass diese keinesfalls abgedeckt oder verbaut werden. Sorgen Sie außerdem für eine großzügig bemessene Luftzirkulation um das Gerät. Damit verhindern Sie mögliche Schäden am Gerät sowie Brandgefahr durch Überhitzung. Achten Sie unbedingt darauf, dass Kabel nicht in die Nähe von Wärmequellen (z.B. Heizkörper, andere Elektrogeräte, Kamin etc.) kommen. Artikel SPU 98-06 SPU 912-06 SPU 916-06 SPU 924-06 SPU 932-06 Frequenzbereich (TERR | SAT) 5…862 MHz | 950…2400 MHz Anzahl der Eingänge 9 Anzahl der Stammausgänge 9 Teilnehmeranschlüsse 8 12 16 24 32 Anschlussdämpfung TERR 24 dB ±2 dB 28 dB ±3 dB 32 dB ±3 dB Anschlussdämpfung SAT 2…0 dB ±2 dB 2…1 dB ±2 dB 2…0 dB ±2 dB 102 dBµV Max. Ausgangspegel Teilnehmeranschlüsse SAT1 Schaltkriterien 13/18 V, 0/22 kHz, DiSEqC 1.0 Durchgangsdämpfung TERR 2…3dB ±1,5 dB 4…5 dB ±1,5 dB 4…6 dB ±1 dB Durchgangsdämpfung SAT 1…2 dB ±1,5dB 1,5…3 dB ±1,5 dB 2...6 dB ±1,5 dB Entkopplung V®H >30 dB Entkopplung TERR-Eing.®SAT-Eing. 30 dB Umgebungstemperaturbereich (gemäß EN 60065) -20…+50°C Stromaufnahme je Teilnehmeranschluss < 45 mA (ohne LNB-Versorgung) Maximaler LNB-Versorgungsstrom 1500 mA Stromaufnahme vom Netzteil 10 mA Potentialausgleichanschluss 4 mm2 Maße (B × H × T) ca. 128 x 202 x 63 mm 189 x 202 x 63 mm 306 x 202 x 63 mm Schutzklasse IP 20 1 3rd order SAT max. EN50083-3 35dB KMA (2 Sender Messmethode) Technische Daten: Hiermit erklärt die AXING AG, dass die gekennzeichneten Produkte den geltetenden Richtlinien entsprechen. WEEE Nr. DE26869279 | Elektrische und elektronische Komponenten nicht mit dem Restmüll, sondern separat entsorgen. Stand 2019-10-14 Technische Verbesserungen, Änderungen im Design, Druckfehler und Irrtümer vorbehalten. Hersteller AXING AG Gewerbehaus Moskau 8262 Ramsen EWR-Kontaktadresse Bechler GmbH Am Rebberg 44 78239 Rielasingen SPU 98-06 | SPU 912-06 SPU 916-06 | SPU 924-06 SPU 932-06 basic-line Multischalter / Kaskadenbausteine Betriebsanleitung Verwendungsbereich: HF-Anschluss: Kaskadierung: Die Geräte sind ausschließlich für den Einsatz zum Verstärken sowie Verteilen von Radio- und Fernsehsignalen im Haus geeignet! Wird ein Gerät für andere Einsätze verwendet, wird keine Garantie übernommen! Die Abbildungen rechts zeigen ein Anwendungsbeispiel für die Verteilung von 8 SAT-ZF-Polarisationsebenen inklusive DVB-C-Signale. Verbinden Sie die SAT-Eingänge des Multischalters mit den LNBs Ihrer SAT-Empfangsantenne. Speisen Sie in den terr. Eingang Ausgangssignale eines terrestrischen Verstärkers bzw. eines BK-Hausanschlussverstärkers ein. Verbinden Sie die seitlichen Teilnehmeranschlüsse (3) des Multischalters mit den Antennensteckdosen. Verwenden Sie hierfür hochgeschirmte Koaxialkabel mit F- Anschlusssteckern. Passende Kabel und Stecker unter www.axing.com. Wichtig: Bevor Sie die Multischalter/Kaskadenbausteine miteinander verbinden, schließen Sie den Potentialausgleich an die Geräte an. Verbinden Sie die Ausgänge der Multischalter mit den Eingängen der Kaskadenbausteine. Verwenden Sie dazu F/F-Quickfix-Adapter CFA 4-01 (nicht im Lieferumfang enthalten). Eingänge (SAT System 1) Eingänge (SAT System 2) TERR Eingang 2 2 4 3 2 3 Ausgänge zu Kaskadenbausteinen LV und HV (unten) 2 1 LV und HV (unten) Wenn Sie keine Kaskadenbausteine am Multischalter anschließen, dann schließen Sie die Kaskadenausgänge unten am Gerät mit DC-entkoppelten 75 Ohm Abschlusswiderständen ab (z. B. CFA 11-00, nicht im Lieferumfang enthalten). Spannungsversorgung: LH und HH (oben) Eingänge (SAT System 1) LH und HH (oben) TERR Input Eingänge (SAT System 2) Potentialausgleich und Montage: Zur Vermeidung gefährlicher Überspannungen (Achtung: Brand-/Lebensgefahr), müssen die Geräte gemäß EN 60728-11 am Potentialausgleich angeschlossen werden. Verwenden Sie den Potenzialaus­gleichsanschluss am Gerät (1). Um die Außenleiter der Koaxialkabel am Potentialausgleich anzuschließen, verwenden Sie z. B. QEW-Erdungswinkel an den Eingängen und zusätzlich Patch-Kabel SAK 21/41-02 an den Teilnehmerausgängen des Geräts. Montieren Sie das Gerät auf einer flachen Oberfläche. Verwenden Sie passende Montageschrauben und die Montagelöcher am Gerät (2). Die Multischalter werden von den angeschlossenen Receivern versorgt. Zur Spannungsversorgung der LNBs wird ein Netzteil SZU 99-06 benötigt (nicht im Lieferumfang enthalten). Verbinden Sie das Netzteil mit dem beiliegenden Kabel mit der DC-Buchse (4). Schließen Sie die Ausgänge des letzten Kaskadenbausteins mit DC-entkoppelten 75 Ohm Abschlusswiderständen ab (z. B. CFA 11-00, nicht im Lieferumfang enthalten). Safety advices: Installation and repairs to the equipment may only be carried out by technicians observing the current guidelines. No liability will be assumed in the case of faulty installation and commissioning. Before handling, the mains plug must be pulled or the power supply removed, otherwise there is a danger to life. This is also valid for cleaning the equipment or working on the connections. Providing that a serviceable fuse exists, the power plug must be pulled out before changing the fuse. Defective fuses may only be replaced with standard compliant fuses that have the same nominal value. The equipment may only be operated in dry rooms. In humid rooms or outdoors there is danger of short-circuit (caution: risk of fire) or electrocution. To prevent damage to your equipment and to avoid possible peripheral damages, the devices foreseen for wall mounting may only be installed on a flat surface. Plan the installation location so that the device can be disconnected from the power supply in hazardous situations. Choose the location of installation or mounting such that children may not play unsupervised near the equipment and its connections. The location of installation or mounting must allow a safe installation of all cables connected. Choose the location of installation or mounting so that under no circumstances liquids or objects can get into the equipment (e.g. condensation, water coming from leaking roofs or flowing water, etc.). Avoid exposure of the equipment to direct sunlight and to other heat sources (e. g. radiators. other electrical devices, chimney, etc.). Devices that are equipped with heat sinks or ventilation slots must under no circum-stances be covered or blocked. Also ensure for a generous air circulation around the equipment. In this way you avoid possible damage to the equipment as well as a risk of fire caused by overheating. Absolutely avoid that cables come near any source of heat (e.g. radioators, other electrical devices, chimney, etc.). Article SPU 98-06 SPU 912-06 SPU 916-06 SPU 924-06 SPU 932-06 Frequency range (TERR | SAT) 5…862 MHz | 950…2400 MHz Number of inputs 9 Number of trunk outputs 9 Subscriber ports 8 12 16 24 32 Tap loss TERR 24 dB ±2 dB 28 dB ±3 dB 32 dB ±3 dB Tap loss SAT 2…0 dB ±2 dB 2…1 dB ±2 dB 2…0 dB ±2 dB 102 dBµV Max. output level subscriber ports SAT1 Switch commands 13/18 V, 0/22 kHz, DiSEqC 1.0 Through loss TERR 2…3dB ±1,5 dB 4…5 dB ±1,5 dB 4…6 dB ±1 dB Through loss SAT 1…2 dB ±1,5dB 1,5…3 dB ±1,5 dB 2...6 dB ±1,5 dB Isolation V®H. >30 dB Isolation TERR input®SAT. input 30 dB Ambient temperature range (acc. to EN 60065) -20…+50°C Current consumption per subscriber port <45 mA (without LNB supply) Max. LNB supply current 1500 mA Stromaufnahme vom Netzteil 10 mA Potentialausgleichanschluss 4 mm2 Maße (B × H × T) ca. 128 x 202 x 63 mm 189 x 202 x 63 mm 306 x 202 x 63 mm Schutzklasse IP 20 1 3rd order SAT max. EN50083-3 35dB KMA (2 Sender Messmethode) Technical data: Herewith AXING AG declares that the marked products comply with the valid guidelines. WEEE Nr. DE26869279 | Electrical and electronic components must not be disposed of as residual waste, it must be disposed of separately. State of the art 2019-10-14 Technical improvements, changes in design, printing- and other errors expected. Manufacturer AXING AG Gewerbehaus Moskau 8262 Ramsen EEA contact address Bechler GmbH Am Rebberg 44 78239 Rielasingen SPU 98-06 | SPU 912-06 SPU 916-06 | SPU 924-06 SPU 932-06 basic-line Multiswitches / Cascade units Operation instructions Field of application: RF Installation: Cascading: The devices are only suitable for in-house distribution of RF signals. If a device is used for other purposes, no warranty is given! The figures on the right show application examples for distribution of 8 SAT IF polarization levels including DVB-C signals. Connect the SAT inputs of the multiswitch to the LNBs of your SAT reception antenna. Connect the output signals of a terrestrial amplifier or a CATV amplifier to the terrestrial input. Connect the subscriber ports (3) on the left and right sides of the multiswitch to the antenna sockets. Use highly shielded coaxial cables with F connectors. Suitable cables and connectors can be found under www.axing.com. Important: Before connecting the multiswitches/cascade units, connect the equipotential bonding to the devices. Connect the outputs of the multiswitches with the inputs of the cascade units. Use F/F Quickfix adapters CFA 4-01 (not included in delivery). Inputs (SAT system 1) Inputs (SAT system 2) 2 TERR Input 2 4 3 2 3 Outputs to cascade units 1 LV and HV (below) 2 LV and HV (below) If you don´t use cascade units to expand the multiswitch, terminate the cascade outputs on the lower side of the device DC-isolated 75 Ohm terminating resistors (e. g. CFA 11-00 not included in delivery). Power supply: LH and HH (above) LH and HH (above) Inputs (SAT system 1) Inputs (SAT system 2) TERR Input Equipotential bonding and mounting: To avoid dangerous power surges (e.g. risk of fire and danger of life) the devices must be connected to the equipotential bonding according to EN 60728-11. Use the equipotential bonding connection at the device (1). To connect the outer conductors of the coaxial cables to the equipotential bonding, use, for example, QEW earthing angle at the inputs and additionally patch cable SAK 21/41-02 at the subscriber outputs of the device. Mount the device on a flat surface. Use appropriate mounting screws and the mounting holes of the device (2). The multiswitches are supplied by the connected receivers. An SZU 99-06 power supply (not included in delivery) is required for power supply of the LNBs. Connect the power supply unit to the DC socket (4) using the enclosed cable. Terminate the outputs of the last cascade units with DC-isolated 75 Ohm terminating resistors (e. g. CFA 11-00 not included in delivery).
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project