Operating Instructions

Sygonix Gateway

Item No. 1898921 / RSL / 433 MHz

Item No. 1898922 / RS2W / 868 MHz

Intended use

The product acts as a power socket and gateway and is equipped with a push button that turns the power supply to attached loads on and off.

As a gateway is controls compatible and linked RS2W (868 MHz) and RSL (433 MHz) products.

The gateway is controlled through WLAN via mobile app, and additionally can be linked to

CONRAD CONNECT for additional functionality.

The product is intended only for the connection to a standard power socket with earth contact.

Refer to the technical data section to learn more about the maximum permissible loads.

The product is only designed for indoor use. Keep away from water and high-humidity sources and the areas where these conditions occur (e.g. bathroom).

Please read the operating instructions carefully and do not discard them. If you pass the prod uct on to a third party, please hand over these operating instructions as well.

Any use other than that described above could lead to damage to this product and involves the risk of short circuits, fire, electric shock, etc. No part of the product may be modified or reconfigured! Please observe the safety instructions at all times!

This product complies with the legal national and European requirements. All names of compa nies and products are the trademarks of the respective owners. All rights reserved.

Package Contents

• Gateway (with socket)

• Operating Instructions

Application

There are compatible Android and iOS apps available from the respective app stores.

Look for the “Sygonix RSL/RS2W” app and download it onto your smart device.

An app instruction manual is available from the URL listed in chapter „Up-to-date oper ating instructions“.

The product is compatible with the

Conrad Connect IoT platform at www.conradconnect.de

Up-to-date operating instructions

Download the latest operating instructions via the link www.conrad.com/downloads or scan the QR code.

Follow the instructions on the website.

Explanation of symbols

The lightning symbol inside of a triangle is used when there is a potential risk of personal injury, such as electric shock.

This symbol indicates specific risks associated with handling, operation or use.

The arrow symbol indicates special tips and operating instructions.

Safety Instructions

The warranty will be void in the event of damage caused by failure to observe these safety instructions! We do not assume any liability for any resulting damage! We shall not accept liability for damage to property or personal injury caused by incorrect handling or non-compliance with the safety instructions!

The warranty/guarantee will be void in such cases!

a) General

• The unauthorized conversion and/or modification of the product is not allowed for safety and approval reasons. Do not open/disassemble!

• The product is designed in accordance with protection class I. Only a standard grounding mains socket of the public supply grid (a wall socket, for example) may be used as a power source.

• The mains socket into which the product is plugged must be easily accessible.

• The product is not a toy and should be kept out of the reach of children. Position the product so it is out of the reach of children.

• The product is equipped with a child safety lock. An integrated mechanism will release the holes of the receptacle only, if the two prongs of a power plug are inserted into the two holes at once. Nevertheless, take special caution when chil dren are around. Children cannot recognize the danger arising from the incorrect use of electrical devices. There is a risk of a life-threatening electric shock!

• Do not leave the packaging material lying around carelessly as it may be a danger to children.

• Handle the product with care; it can be damaged by impacts, blows or falls even from a low height.

b) Operating location

• The product may only be used in dry interiors; it must not get damp or wet! Never position the product in direct vicinity of a bathtub, shower, bathroom, swimming pool, or similar. Lethal hazard due to electric shock!

• The product must not be exposed to extremes of temperature, direct sunlight or strong vibrations. Keep the product away from strong magnetic fields generated by machines, electric motors or loudspeakers.

• Do not operate the device in environments where there are high levels of dust, flammable gases, vapours or solvents. There is a danger of fire and explosion!

• Do not use this product in hospitals or medical institutions. Radiowaves may inter fere with medical equipment. The same may also apply to other areas.

c) Handling and Use

• Never plug in, unplug or operate the product when your hands are damp or wet.

There is a risk of a life-threatening electric shock! The same applies for the load that is plugged into the socket of the product.

• Never connect the product to the power supply immediately after it has been trans ferred from a cold room into a warm one (e.g. during transport). The condensation that forms might destroy the device. Moreover, there is danger of electric shock!

Allow the product to reach room temperature. Wait until the condensation has evaporated. This might take several hours. Only then the product may be plugged into the mains socket and put into use.

• Always use the gripping surface to pull a mains plug out of the product. Never unplug a mains plug from a mains socket by pulling the cable.

• Never overload the product. Note the maximum permissible connected load in the chapter ‘Technical Data’.

• Do not connect in series! This can lead to an overload of the product! There is a risk of fire!

• Do not operate while covered! At higher connected loads, the product becomes warm, which can lead to overheating and potentially a fire if covered!

• Disconnect the product from the mains socket in thunderstorms for reasons of safety.

• Volt-free only, if unplugged!

• Do not use the product if it is damaged. There is a risk of a life-threatening electric shock! In this case, dispose of the product in an environmentally correct manner.

Safe operation can no longer be assumed if:

the product shows visible signs of damage

the product does not work at all or works poorly (leaking smoke or a smell of burning, audible cracking noises, discolouration to the product or the adjacent surfaces)

the product was stored under unfavourable conditions

it was exposed to heavy loads during transport

• Never pour any liquids above or next to the product. You run the risk of causing a fire or a fatal electric shock. If any liquid has still managed to enter the device, immediately switch off the power supply to the mains socket at which the product is connected (turn off the fuse / circuit breaker / residual current operated circuit breaker of the associated circuit). Only then can you unplug the product from the mains socket and contact a specialist. Do not use the product any longer.

• Always pull the product out of the mains socket (e.g. wall socket) before cleaning it or when the device will not be in use for a long time (e.g. for storage).

• Use the product only in a temperate climate, never in a tropical climate.

• If you have any questions that are not answered in this manual, please contact our technical service or another specialist.

Control Elements

3

4

Placement

The transmission distance indicated in the ‘Technical Data’ section is the maximum theoretical transmission distance. When you place the product, keep signal interference in mind.

The range can be considerably reduced due to:

• Walls, reinforced concrete ceilings, metal-framed drywalls

• Coated/metallised insulated glass

• Proximity to metallic and conductive objects (e.g., heating elements)

• Proximity to human bodies

• Other devices on the same frequency (e.g. wireless headphones, wireless speakers)

• Proximity to electric motors/appliances, transformers, power supplies, computers

Connection

Plug the gateway into a regular grounded mains socket (wall socket) of the public supply grid.

Refer to the ‘LED Statuses’ chapter for an overview of statuses indicated.

For instructions on connecting the gateway to your WLAN network, refer to the app instruction manual. Also, refer to the ‚Technical Data‘ section to learn more about supported WLAN technologies.

Operation

• Press the On/Off button (2) to turn on and off the power supply to the connected load. Refer to the ‘LED Statuses’ chapter for an overview of statuses indicated.

• Plug the desired load into the receptacle (3) of the gateway.

Additional functionality is available in connection with the accompanying app. Make sure to read the app instruction manual.

LED Statuses

Status

Socket is off

Socket is on

Ready to connect to Router/Access Point/App

Connecting to Router/Access Point/App

Connected to Router/Access Point/App

LED Indicator Light

Solid blue

Solid red

Flashes red/blue

Flashes red/blue

Connected to server: Solid blue

Not connected to server: Flashes red

Resetting

1

2

1 LED indicator light

2 On/Off button

3 Receptacle

4 Mains connection

Resetting is necessary if you want to use the product on a different network.

Resetting the gateway removes all settings necessary for the WiFi connection.

Proceeds as follows:

1. Switch the product off.

2. Long press the On/Off button until the indicator light flashes alternatingly blue and red.

3. The reset procedure is completed.

See chapter “Connection” for details on re-connecting.

Maintenance and Cleaning

• The product does not require any maintenance. You should not open/disassemble it. Repair or maintenance work must be carried out by a specialist.

• Before cleaning, disconnect the product from the power supply. To do this, pull it completely out of the mains socket.

• Disconnect connected loads.

• You can use a clean, dry, soft cloth for cleaning. Dust can be very easily removed with a soft, clean brush and a vacuum cleaner.

• Do not use aggressive chemical or scouring cleaning agents, as this may lead to discoloura tion or changes in the material on the surface.

Declaration of Conformity (DOC)

Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, herewith declares that this product conforms to the 2014/53/EU directive.

The full text of the EU declaration of conformity is available at the Internet address below: www.conrad.com/downloads

Select a language by clicking on the corresponding flag icon, and then enter the order number of the product into the search box. You may then download the EU declaration of conformity as PDF file.

Disposal

Electronic devices are recyclable waste and must not be disposed of in the house hold waste. At the end of its service life, dispose of the product in accordance with applicable regulatory guidelines.

You thus fulfil your statutory obligations and contribute to the protection of the envi ronment.

Technical data a) General

Rated Input ................................... 230 V/AC, 50 Hz, 12 A

Resistive load ............................... max. 2000 W

Overcurrent protection .................. 12 A

Overload protection ...................... 2760 W

Standby power consumption ........ <1 W

Actuators ...................................... max. 50

Protection class ............................ I

Child proof .................................... yes

Operating conditions ..................... 0 to +35 °C,

10 – 90 % relative humidity, non-condensing

Storage conditions ........................ -10 to +55 °C,

5 – 90 % relative humidity, non-condensing

Dimensions (W x H x D) ............... 55 x 108 x 73 mm

Weight .......................................... approx. 122 g

b) Wi-Fi

WLAN technology ......................... IEEE 802.11 b/g/n, 2.4 GHz

Security ......................................... WPA, WPA2, WPA/WPA2

Output power ................................ IEEE 802.11b: 17 ±2 dBm

IEEE 802.11g: 14 ±2 dBm

IEEE 802.11n: 13 ±2 dBm

Transmission range ...................... Wi-Fi: max. 10 m (indoors)

c) 433/868 MHz

Frequency ..................................... 433 MHz (Item 1898921)

868 MHz (Item 1898922)

Output power ................................ 433 MHz: <10 dBm

868 MHz: <14 dBm

Transmission range ...................... max. 100 m

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.

This publication represent the technical status at the time of printing.

Copyright 2019 by Conrad Electronic SE. *1898921_1898922_v1_0419_02_jh_m_en_(7.0)