advertisement
BigDog
®
Mowers Alpha
General Service Manual
119293
200 South Ridge Road
Hesston, Kansas
67062
REV B
The engine exhaust from this product contains chemicals known to the state of California to cause cancer, birth defects or other reproductive harm.
NOTICE OF REQUIREMENT OF SPARK ARRESTER MUFFLER
This equipment may create sparks that can start fires around dry vegetation. California Public Resources Code
Section 4442.6 provides that it is unlawful to use or operate an internal combustion engine on any forest-covered, brush-covered, or grass-covered land unless the engine is equipped with a spark arrester maintained in effective working order. A spark arrester is a device constructed of nonflammable materials specifically for the purpose of removing and retaining carbon and other flammable particles over 0.0232 of an inch in size from the exhaust flow of an internal combustion engine that uses hydrocarbon fuels or which is qualified and rated by the United States
Forest Service. Other states or federal areas may have similar laws. The Operator Should Contact Local Fire
Agencies For Laws or Regulations Relating to Fire Prevention Requirements. THIS EQUIPMENT DOES NOT HAVE
A SPARK ARRESTER AND YOU SHOULD CONTACT YOUR AUTHORIZED DEALER FOR THE PURCHASE OF
A SPARK ARRESTER.
Inspect spark arrester daily; replace every 500 hours or as needed.
The Engine Owner’s Manual provides information regarding the U.S. Environmental Protection Agency (EPA) and the California Emission Control Regulation of emission systems, maintenance and warranty.
Keep Engine Owner’s Manual with your unit. Should the Engine Owner’s Manual become damaged or illegible, replace immediately. Replacements may be ordered per the information found in the Product
Information section of the owner’s manual.
Federal law and California State law prohibit the following acts or the causing thereof:
1. The removal or rendering inoperative by any person other than for purposes of maintenance, repair, replacement, of any device or element of design incorporated into any equipment for the purposes of emissions control prior to or after its sales or delivery to the ultimate purchaser or while it is in use, or
2. The use of the equipment after such device or element of design has been removed or rendered inoperative by any person.
REV B 119293
119293
TABLE OF CONTENTS
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
®
Mowers Service Program . . . . . . . . . . . . . . . . . . . . . . 1-1
Maintenance Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Safe Servicing Practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Pre-Operation Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Operation Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Operate Machine Safely. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
General Maintenance Precautions . . . . . . . . . . . . . . . . . . . . . . . 2-2
Maintenance Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Standard Torques. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Special Torques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Power Unit Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Steering Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Park Brake Spring Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Transaxle Drive Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Engine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
General Engine Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Engine Oil and Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Engine Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Fuel evaporation system filter . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Engine RPM Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Deck Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Deck Leveling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Deck Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
36”/42" Deck Belt Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
52" Deck Belt Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
t-1 REV B
Electrical Schematic — Kawasaki . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Maintenance Locator Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
REV B t-2 119293
GENERAL INFORMATION
BigDog
®
Mowers Service Program
This manual is part of a service package for the BigDog
®
Alpha mowers. Use of this manual in conjunction with other
BigDog
®
mower and component manuals will provide the information necessary to service and maintain the BigDog
®
Alpha mower.
This General Service Manual is a service guide for use by
Service Technicians. It provides the necessary information needed to perform normal maintenance requirements on these units.
The Parts Manual provides a complete parts listing for the unit. Use this manual when ordering parts.
The Operator's Manual provides fundamental operational information and operational safety that is needed when operating the mower.
The component manuals are furnished by the various manufacturers to be used for the troubleshooting and servicing of their components.
Maintenance Introduction
Regular maintenance is the best prevention for downtime or premature failure. The following pages contain suggested maintenance information and schedules which the operator/mechanic should follow on a routine basis.
Remain alert for unusual noises, they could be signaling a problem. Visually inspect the machine for any abnormal wear or damage. A good time to detect potential problems is while performing scheduled maintenance service. Correcting the problem as quickly as possible is the best insurance.
Clear away heavy build-up of grease, oil and dirt, especially in the engine compartment and under the seat platform areas; minute dust particles are abrasive to close-tolerance engine and hydraulic assemblies.
Daily inspect mower for grass clippings and wire and string tangles. The underside of the mower deck will collect a build-up of grass clippings and dirt, especially when grass is wet or has high moisture content. This build-up will harden, restricting blade and air movement and will probably show a lesser quality of cut. Therefore it should be removed routinely.
To do this it will be necessary to raise and block the deck, using jack stands or blocks, in the full up position and scrape the build-up from underneath.
Some repairs require the assistance of a trained service mechanic and should not be attempted by unskilled personnel.
Consult your BigDog
®
Mowers service center when assistance is needed.
Information included in this manual was current at the time of printing, but subsequent production changes may cause your machine to vary slightly in detail. BigDog
®
Mowers reserves the right to redesign and change the machine as deemed necessary, without notification. If a change has been made to your machine which is not reflected in this service manual contact the Customer Service Department at BigDog
®
Mowers for additional information.
Warranty
Warranty repair must be performed by a BigDog
®
Mowers
Authorized Dealer before warranty credit can be allowed. Work performed by anyone other than an Authorized Dealer will invalidate the warranty claim and warranty credit will not be approved.
119293 1-1 REV B
REV B 1-2 119293
SAFETY
This safety alert symbol is used to call attention to a message intended to provide a reasonable degree of PERSONAL
SAFETY for operators and other persons during the normal operation and servicing of this equipment.
DANGER
– denotes immediate hazards which WILL result in severe personal injury or death.
WARNING
– denotes a hazard or unsafe practice which COULD result in severe personal injury or death.
Safe Servicing Practices
This product is capable of amputating hands and feet and throwing objects. Always follow all safety instructions to avoid serious injury or death.
Understand correct service
Be sure you understand a service procedure before you work on the machine.
Unauthorized modifications to the machine may impair the function and/or safety and affect machine life.
If it is necessary to make checks with the engine running, always use two people - with the operator at the controls, able to see the person doing the checking.
Pre-Operation Precautions
Fuel Handling
To avoid personal injury or property damage, use extreme care in handling fuel. Fuel is extremely flammable and the vapors are explosive.
Observe usual fuel handling precautions:
• Do not smoke while refueling. Extinguish all cigarettes, cigars, pipes and other sources of ignition.
• Do not remove fuel cap or fill tank with engine running or while engine is hot. Clean up any fuel spills.
• Allow engine to cool before storing machine inside a building.
• Keep fuel away from open flame or spark and store machine away from open flame or spark or pilot light such as on a water heater or appliances.
• Use extreme care when handling gasoline and other fuels. They are extremely flammable and vapors are explosive. A fire or explosion from fuel can burn you and others and can damage property.
119293 2-1
• Refuel outdoors. Never refuel or drain the fuel from the machine indoors.
• Never attempt to start engine when there is a strong odor of gasoline or diesel fuel fumes present. Locate and correct cause.
• Store fuel in an approved container and keep it out of the reach of children. Never buy more than a 30 day supply of fuel.
• Do not fill fuel containers inside a vehicle or on a truck or trailer bed with interior carpets or plastic truck bed liners. Always place fuel containers on the ground away from your vehicle before filling.
• When practical, remove gas or diesel fuel powered equipment from the truck or trailer and refuel the equipment with its wheels on the ground. If this is not possible, then refuel such equipment on the truck or trailer using a portable container and not a fuel dispenser nozzle. If a fuel dispenser nozzle must be used, keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open device.
• Never use gasoline or diesel fuel for cleaning parts.
• Read and observe safety precautions elsewhere in this manual.
Gasoline and diesel fuel is harmful or fatal if swallowed.
• Long-term exposure to vapors can cause serious injury and illness.
• Avoid prolonged breathing of vapors.
• Keep face away from nozzle and gas tank or fuel container opening.
• Keep fuel away from eyes and skin.
• If fuel is spilled on clothing, change clothing immediately.
Understand Machine Operation
Only qualified and trained personnel should operate the equipment.
Carefully read the operator’s manual and all manuals furnished with the attachments. Learn the location and purpose of all controls, instruments, indicators and labels.
Wear Protective Clothing
Do not operate or service the equipment while wearing sandals, tennis shoes, sneakers, shorts or any type of loose fitting clothing. Long hair, loose clothing or jewelry may get tangled in moving parts. Always wear long pants, safety glasses, ear protection and safety shoes when operating or servicing this machine.
Always wear adequate eye protection when servicing the hydraulic system and battery, or when grinding mower blades and removing accumulated debris.
Prolonged exposure to loud noise can cause impairment or loss of hearing.
• Always wear adequate ear protection, such as earplugs, when operating this equipment as prolonged exposure to uncomfortable or loud noises can cause impairment or loss of hearing.
REV B
• Do not wear radios or music headphones while operating the machinery. Safe operation requires your full attention.
Operation Precautions
Avoid Fire Hazards
Clean flammable material from machine. Prevent
fires by keeping engine compartment, top of deck, exhaust area, battery, hydraulic lines, fuel line, fuel tank and operator’s station clean of accumulated trash, grass clippings, and other debris. Always clean up spilled fuel and oil.
Start Engine Safely
Avoid possible injury or death from machine runaway.
Do not start engine by shorting across starter terminals.
Before you start the engine:
• Sit on the operator’s seat.
• Move control levers to the neutral/brake position.
Operate Machine Safely
Refer to the unit’s operator’s manual for complete safety information on safe machine operation.
Always maintain a safe distance from people and pets when mowing
Always be aware of what is behind the machine before backing up.
Never leave machine unattended with ignition key in switch, especially with children present.
Follow daily and weekly checklists, making sure hoses are tightly secured and bolts are tightened.
Always keep engine and machine clean, removing accumulated dirt, trash and other material from machine.
Never put hands or feet under any part of the machine while it is running.
Never attempt to start engine when there is a strong odor of gasoline fumes present. Locate and correct cause.
Keep all safety shields and covers in place, except for servicing.
Do not touch hot parts of machine.
General Maintenance Precautions
Repairs or maintenance requiring engine power
should be performed by trained maintenance personnel only.
Never run the engine in an enclosed area unless exhaust is vented to the outside. Exhaust gases contain carbon monoxide which is an odorless and deadly poison.
Unless specifically required, DO NOT have engine running when servicing or making adjustments to mower.
Park the machine on level ground. Place steering control levers in the park brake position, disengage deck clutch, lower deck, remove ignition switch key and disconnect negative battery cable before doing any maintenance.
Wait for all movement to stop before adjusting, cleaning or repairing. To prevent carbon monoxide poisoning, be sure proper ventilation is available when engine must be operated in an enclosed area.
REV B 2-2
Before working on or under the deck, make certain engine cannot be accidentally started. Shut engine off, remove ignition switch key and disconnect negative battery cable for maximum safety.
Except when changing or checking belt, always keep belt covers on mower deck for safety as well as cleanliness.
Use a stick or similar instrument to clean under the mower making sure that no part of the body, especially arms and hands are under mower.
Keep your machine clean and remove any deposits of trash and clippings, which can cause engine fires and hydraulic overheating as well as excessive belt wear.
Clean up oil or fuel spillage. Allow machine to cool before storing.
Always wear adequate eye protection when servicing the hydraulic system and battery, or when grinding mower blades and removing accumulated debris.
Never attempt to make any adjustments or repairs to the mower drive system, mower deck or any attachment while the engine is running or deck clutch is engaged.
Exercise caution when releasing spring tension from any of the belt idlers or when working with any of the deck lift components.
Never work under the machine or attachment unless it is safely supported with jack stands. Make certain machine is secure when it is raised and placed on the jack stands.
The jack stands should not allow the machine to move when the engine is running and the drive wheels are rotating. Use only certified jack stands. Use only appropriate jack stands, with a minimum weight rating of 2000 pounds to block the unit up. Use in pairs only. Follow the instructions supplied with the vehicle stands.
Keep nuts and bolts tight, especially the blade attachment bolts. Keep equipment in good working condition.
Never tamper with safety devices. Check their proper operation regularly.
Exercise caution when working under the deck as the mower blades are extremely sharp. Wrap the blade(s) or wear gloves and use extra caution when servicing them.
Use only genuine BigDog
®
Mower replacement parts to ensure that original standards are maintained.
Maintenance Precautions
Avoid Fire Hazards
Be prepared if an accident or fire should occur. Know where the first aid kit and the fire extinguishers are located and how to use them.
Provide adequate ventilation when charging batteries.
Do not smoke near battery.
Never check fuel level with an open flame.
Never use an open flame to look for leaks anywhere on the equipment.
Never use an open flame as light anywhere on or around the equipment.
When preparing engine for storage, remember that fuel stabilizer is volatile and therefore dangerous. Seal and tape openings after adding the inhibitor. Keep container tightly closed when not in use.
119293
Inspect electrical wiring for worn or frayed insulation.
Install new wiring if wires are damaged.
Prepare For Emergencies
Be prepared if a fire starts.
Keep a first aid kit and fire extinguishers available.
Keep emergency numbers for doctor, ambulance service, hospital, and fire department near the telephone.
Prevent Battery Explosions
Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm.
Wash hands after handling.
Charge batteries in an open well-ventilated area, away from sparks and flames. Unplug charger before connecting or disconnecting from battery. Wear protective clothing and use insulated tools.
Avoid skin and clothing contact with battery acid.
• Always wear eye protection when checking the battery, acid can cause serious injury to skin and eyes. If contact occurs, flush area with clean water and call physician immediately. Acid will also damage clothing.
• Do not drink the battery electrolyte.
• Do not allow open flame near the battery when charging.
• Hydrogen gas forms inside the battery. This gas is both toxic and flammable and may cause an explosion if exposed to flame. Always disconnect the negative
(black) battery cable(s) before disconnecting the positive (red) cable(s). Always connect the positive (red) battery cable(s) before connecting the negative (black) cable(s).
• Do not overfill battery.
• Electrolyte may overflow and damage paint, wiring or structure. When cleaning the battery, use soap and water. Be careful not to get soap and water into the battery. Clean the battery terminals with a solution of four parts water and one part baking soda when they become corroded.
Shorts caused by battery terminals or metal tools touching metal mower components can cause sparks. Sparks can cause a battery gas explosion which will result in personal injury.
• Prevent the battery terminals from touching any metal mower parts when removing or installing the battery.
• Do not allow metal tools to short between the battery terminals and metal mower parts.
Incorrect battery cable routing could cause damage to the mower and battery cables. This can cause sparks which can cause a battery gas explosion which will result in personal injury. Always disconnect the negative (black) battery cable(s) before disconnecting the positive (red) cable(s). Always connect the positive (red) battery cable(s) before connecting the negative (black) cable(s).
Avoid Acid Burns
Sulfuric acid in battery electrolyte is poisonous. It is strong enough to burn skin, eat holes in clothing and cause blindness if splashed in eyes.
Avoid the hazard by:
• Filling batteries in a well-ventilated area.
• Wearing eye protection and rubber gloves.
• Avoiding breathing fumes when electrolyte is added.
• Avoiding spilling or dripped electrolyte.
If you spill acid on yourself:
• Flush your skin with water.
• Apply baking soda or lime to help neutralize the acid.
• Flush your eyes with water for 10-15 minutes. Get medical attention immediately.
If acid is swallowed:
• Drink large amounts of water or milk.
• Then drink milk of magnesia, beaten eggs or vegetable oil.
• Get medical attention immediately.
119293 2-3 REV B
REV B 2-4 119293
TORQUE
Standard Torques
The following chart lists the standard torque values for the threaded fasteners found in this manual. Torque all cap screws, nuts and set screws to these values unless a different torque is shown in the Special Torques section.
S
IZE
.438
.500
.562
.625
#10
.250
.312
.375
.750
.875
Special Torques
F
T
-L
BS
32.4 IN.-LBS.
98.4 IN.-LBS.
204 IN.-LBS.
30
48
73
105
145
260
420
N-
M
65
99
143
200
3.6
11.1
23
40
350
565
S
IZE
M8
M10
M12
M14
M3
M4
M5
M6
M16
M20
F
T
-L
BS
12 IN.-LBS.
26.4 IN.-LBS.
54 IN.-LBS.
92.4 IN.-LBS.
222 IN.-LBS.
37
64
103
160
320
N-
M
25
50
87
140
1.3
3
6.1
10.4
215
435
D
ESCRIPTION
Wheel (lug) nuts
1
Blade spindle bolt top
Blade spindle bolt bottom
Electric clutch mounting bolt
3
Front wheel axle bolt
Transaxle hub nut
Transaxle pump pulley nut
Engine torques
2
NOTE:
1.
Lug nuts only – It is recommended that these be checked after the first 2 hours of operation and every 50 hours and following removal for repair or replacement.
2.
Engine torque values – Refer to the respective engine owner’s manual.
3.
If clutch mounting bolt is loosened or removed, do not
re-use. Replace with a new bolt. Use only hand tools to install this fastener.
F
T
-L
BS
N-
M
70
60
48
47
95
81.3
65
63.7
Tighten the nut, then back it off until the wheel spins freely.
200 271.2
50
N/A
67.8
N/A
WARNING
Particular attention must be given to tightening the drive wheel lug nuts and blade spindle bolts. Failure to correctly torque these items may result in the loss of a wheel or blade, which can cause serious damage or personal injury.
119293 3-1 REV B
REV B 3-2 119293
POWER UNIT MAINTENANCE
Steering Adjustments
Steering control lever neutral adjustment
The mower’s steering has been factory adjusted to eliminate creeping when the steering control levers are in the neutral position. However, should the mower begin to creep, the steering control lever linkage can be adjusted.
Before considering any adjustment, check the tire air pressure.
Unequal tire pressure will cause the mower to drift to one side.
Refer to tire pressure information in the Tire section for detailed information.
NOTE: Proper park brake adjustment must be completed before the steering control lever neutral adjustment can be done.
Refer to the Park Brake Spring Adjustment section for detailed information.
Fine adjustment to the unit’s steering is made with the transmission’s control rod.
Neutral is properly adjusted when the steering control levers are in the park brake position and the transmissions do not
“whine”.
If this occurs, the steering control linkage may be adjusted as follows:
WARNING
This procedure will require that the unit to be raised and blocked up off of the ground. It is necessary for the wheels to rotate without coming in contact with the floor or any object that would permit the unit to propel itself.
Stay clear and exercise caution when rotating wheels to prevent injury. Use only appropriate vehicle stands, with a minimum weight rating of 2000 pounds to block the unit up. Use in pairs only. Follow the instructions supplied with the vehicle stands.
2. Raise the rear of the mower and block with certified jack stands. Remove the rear wheels.
3. Chock the front tires.
4. Make sure both steering control levers are in the park
Steering control levers in park brake position
Figure 4-1
5. Loosen the nuts adjacent to the steering bushing. Figure
Bushing
Nuts
WARNING
Keep hands, hair, clothing, etc., clear of the pulleys on top of the transmissions. Exercise extreme caution.
WARNING
Untrained maintenance personnel should never attempt to make any adjustments or repairs to the mower’s drive system while the engine is running. The following proce-
dures should be performed by trained maintenance personnel only.
1. Shut engine off, place steering control levers in the park brake position, disengage deck clutch, remove ignition switch key and disconnect negative battery cable before doing any adjustments.
119293 4-1
Figure 4-2
6. Place a clamp on the transmission pump arm as shown in
7. Tighten the nuts against steering bushing (Figure 4-4).
Verify that the pump arms are still in the neutral position
8. Move the steering control levers out of the park brake position and push fully forward, verify that the pump arm does not bottom out against the stop on the transmission.
Move the levers to the full reverse position and release.
Verify that the levers return near to the neutral position.
9. The steering control levers should be adjusted so that they align vertically with each other when in the neutral position (Figure 4-5). Space between ends of steering control handles to be .50” ±.25”. Figure 4-5
10. Check to make sure all tools or obstructions are removed from under the mower.
REV B
Clamp
Bushing
Figure 4-3
Control lever stops adjustment.
WARNING
Keep hands, hair, clothing, etc., clear of the rotating drive wheels/hubs during this process. Exercise extreme caution.
The steering control lever stops may be adjusted to help drive straight when the steering control levers are pushed forward against the stops.
1.
Raise the rear of the mower and block with certified jack stands.
2.
Chock the front tires.
3.
Make sure both steering control levers are in the park
Steering control levers in park brake position
Align handles
± .125”
Nuts
Figure 4-4
11.
Re-install the rear wheels. Torque lug nuts to 70 ft.-lbs.
(95 N
M
)
12.
Raise the rear of the mower and remove the jack stands.
Lower the mower.
13.
Re-attach the negative battery cable.
14.
Close the seat platform
REV B
Figure 4-5
4-2
Figure 4-6
4.
Raise the seat platform and disconnect the mower harness from the seat switch. Bypass the seat switch by connecting the two mower harness female spades together.. Figure 4-7
WARNING
Do not operate (drive) the mower without plugging the mower’s wiring harness into the seat switch. This switch is an important part of the safety start interlock system.
Serious injury can result if the seat switch is not plugged into the mower’s wiring harness.
5.
Start the engine and move both steering control levers forward against the stops in the steering cover.
6.
Determine if the drive wheels are rotating equally or if one is faster than the other. If the wheels are not the same speed, proceed to the next step.
7.
Shut engine off and place the steering control levers in the park brake position
8. Loosen the cap screw under the seat platform on the side which is rotating too fast. Tighten the cap screw on the top of the steering cover to adjust the drive straight bracket up to stop the steering control lever sooner.
Repeat this procedure until both drive wheels rotate at the same speed. Figure 4-8
119293
Drive straight bracket
Cap screws
Seat switch
Female spade
Female spade
Mower harness
Figure 4-8
1. Shut engine off, place steering control levers in the park brake position, disengage deck clutch, remove ignition switch key and disconnect negative battery cable before doing any adjustments.
2. Make sure steering control levers are in the park brake position.
3. Adjust the nylock nut on the end of the brake rod so that
0.625" of thread is showing. Repeat for other side. Figure
4.
Reconnect the negative battery cable.
5.
Close seat platform and re-install seat platform hardware.
Figure 4-7
9. Tighten the cap screws under the seat platform on both sides to lock the drive straight brackets in place. Snug the cap screws on the top of the steering cover so they don't move during operation.
10.
IMPORTANT: With the engine off, disconnect the two female spade connectors from each other (from step #4) and reconnect them to the seat switch. This must be completed so that the safety circuit is functioning properly. Figure 4-7
11.
Lower the seat platform and secure in place.
WARNING
Do not operate the mower without plugging the mower’s wiring harness into the seat switch. This switch is an important part of the safety start interlock system. Serious injury can result if the seat switch is not plugged into the mower’s wiring harness.
.625”
WARNING
Figure 4-9
Transaxle Drive Belt
Never operate the mower with a non-functioning seat switch. Always reconnect the seat switch to the mower harness.
Park Brake Spring Adjustment
Occasionally check the park brake spring adjustment using the following method:
119293 4-3
Inspect belts frequently for wear and serviceability. Replace a belt that shows signs of severe cuts, tears, separation, weather checking and cracking, or burns caused by slipping. Slight raveling of belt covering does not indicate failure; trim ravelings with a sharp knife.
Inspect the belt pulley grooves and flanges for wear. A new belt, or one in good condition, should never run against the bottom of the groove. Replace the pulley when this is the case, oth-
REV B
erwise, the belt will lose power and slip excessively.
Never pry a belt to get it on a pulley as this will cut or damage the fibers of the belt covering.
Keep oil and grease away from belts, and never use belt dressings. Any of these will destroy the belt composition in a very short time.
Belt adjustment
The transaxle drive belt tension remains constant by means of a tension idler and spring. There is no tension adjustment of this belt. Figure 4-10
NOTE: Inspect the belt every month and replace as needed.
Replace the belt every two (2) years.
Belt replacement
WARNING
This procedure will require that the mower to be raised and blocked up off of the ground. Use only appropriate vehicle stands, with a minimum weight rating of 2000 pounds to block the unit up. Use in pairs only. Follow the instructions supplied with the vehicle stands.
WARNING
If the transaxle belt fails, loss of control will occur especially when operating on a slope. If you lose steering control while operating the machine, place the steering control levers in the park brake position immediately.
Inspect the machine and involve your dealer to resolve the problem.
Transaxle drive belt
Spring
WARNING
Allow the engine and muffler to cool before proceeding with the following procedure.
1.
Park the mower on a flat surface and stop the engine.
Make sure deck clutch switch is in the down (OFF) position. Remove ignition key. Place the steering control levers in the park brake position. Make sure the blades are stopped before leaving seat. Disconnect the negative battery cable.
2.
Lower the deck to the lowest setting.
3.
Raise the rear of the mower and block with certified jack stands.
4.
Remove the deck covers. Figure 4-11 & Figure 4-12
Spring mount
Tensioning
Idler spring
Tension idler
REV B
Figure 4-10
4-4
Deck cover
Deck cover
Figure 4-11
5.
Using a tension spring hook (Hustler part number
604462) disconnect the tension idler spring from the spring mount to release tension from the deck drive belt.
Figure 4-13
NOTE: The spring and spring mount will become loose and can become misplaced. Set these aside after removal
119293
Spring mount
Transaxle drive belt
Transaxle drive pulley
Tensioning
Idler spring
Deck cover
Deck cover
Figure 4-12
for easier access upon re-assembly.
WARNING
Exercise caution when releasing spring tension from the belt idler.
Tension idler spring
Deck drive belt
Figure 4-14
Viewed from top of the mower
Transaxle drive pulley
Transaxle drive belt
Tension idler
Transaxle drive pulley
Idler arm
Engine pulley
Electric clutch pulley
Transaxle drive pulley
Tension spring hook (604462)
Spring mount
Figure 4-13
6.
Remove the deck drive belt from the electric clutch pulley located on the engine shaft. Figure 4-14
NOTE: Do not remove the deck drive belt from the deck spindle pulleys. It will only need to be removed from the electric clutch pulley at the rear of the mower.
7.
Locate the tension idler spring. Securely clamp locking pliers onto the spring at the end located next to the idler arm. Figure 4-10
8. Release the transaxle drive belt tension, using the locking pliers, to remove the tension spring from the idler arm.
Swing the idler arm out of the way. Figure 4-14
9.
Remove the transaxle drive belt from the transaxle drive pulleys and the engine pulley. Figure 4-14
10.
Replace the transaxle drive belt and route it around the
119293 4-5
Figure 4-15
11.
Make sure the transaxle drive belt is routed correctly around the tension idler before attaching the tension spring. Using the locking pliers, re-attach the tension spring to the idler arm to re-tension the transaxle drive belt. Remove the locking pliers from the tension spring.
Figure 4-14
12. Reroute the deck drive belt around the electric clutch pulley. Make certain the belt is routed properly around the spindle pulleys and stationary idler pulley(s). Using the tension spring hook (604462), re-tension the deck drive belt by pulling on the deck belt idler spring and hooking it in the spring mount on the deck. Figure 4-11,
Figure 4-12, Figure 4-13 & Figure 4-14
13. Re-install the deck covers.
WARNING
Never operate the mower without the deck covers in place.
REV B
14.
Raise the rear of the mower and remove the jack stands.
15.
Lower the mower.
16.
Re-attach the negative battery cable.
Tires
It is important for level mowing that the tires have the same amount of air pressure. The recommended pressures are:
Drive wheels . . . . . . . . . . . . . . . . . . . . . 8-12 psi (55-83 KPa)
Front wheels . . . . . . . . . . . . . . . . . . . . . 8-12 psi (55-83 KPa)
If you wish to use non-pneumatic tires on your BigDog
®
mower the tires must be an approved tire purchased from Big-
Dog
®
Mowers. Warranty claims will be denied on any mower equipped with unapproved non-pneumatic tires.
REV B 4-6 119293
ENGINE MAINTENANCE
General Engine Maintenance
Detailed instructions and recommendations for break-in and regular maintenance are specified in the Engine Owner’s Man-
ual. Please refer to this manual for engine servicing, lubricating oil levels with quality and viscosity recommendations, bolt torques, etc. The engine warranty is backed by the manufacturer.
Special attention should be paid to applicable data which will not be duplicated here.
Engine Oil and Filter
WARNING
If the engine has been running and is up to operating temperature, allow the engine to cool before changing the oil.
Engine and engine oil will be very hot, so be very careful when changing oil and wear the appropriate protective gear to avoid being burned or exposed to engine oil.
Check engine oil daily and after every 4 hours of operation.
Mower must be on a level surface when checking oil. Refer to engine manual and maintenance schedule for oil recommendation and capacities.
Change the engine oil and filter after the first 5 hours of operation and then per the engine manufacturer’s recommendations after that. If mower is being operated in extremely dirty conditions, then it is recommended oil be changed more frequently.
IMPORTANT: After the new oil filter has been installed, clean up any oil which may have spilled onto the engine plate, muffler, and heat shield.
Draining the engine oil :
1.
Locate the oil drain valve on the lower right side of the engine.
2.
Locate the oil drain hose that was supplied with the machine. Be sure to clean and clear it of debris that might block the flow of the engine oil. Figure 5-1
3. Attach one end of the hose onto the oil drain valve nipple.
Make sure the hose is pushed all the way onto the valve.
4.
Position the loose end of the hose forward and down in front of the right side transmission so that it can drain into a suitable oil drain container.
5. With the hose in position, use a 10 mm wrench or socket and open the valve approximately 4 turns in the counterclockwise direction. Allow 10 minutes for engine oil to adequately drain.
6. After oil is drained, close the valve by turning it in the clockwise direction until it is fully closed.
7.
Once the valve is closed, carefully remove the oil drain hose and clean up any spilled oil.
IMPORTANT: All oil drips or spills must be cleaned off of the exhaust system before operating the machine.
8.
Clean the oil drain hose and store it appropriately. Figure
5-1
Oil drain hose
Oil drain valve
Figure 5-1
Engine Air Filter
Perform engine air filter maintenance per the Maintenance
Schedule shown elsewhere in this manual.
Fuel evaporation system filter
All BigDog
®
Alpha mowers have a fuel evaporation system filter. This filter must be checked and replaced every 100 hours or annually whichever comes first. Figure 5-2
Fuel evaporation system filter
Figure 5-2
119293 5-1 REV B
Engine RPM Settings
The engine rpm’s are set at the factory for maximum mowing efficiency. Occasionally it may be necessary to check and adjust the settings. The idle speeds should be set as follows:
FR651 / FR691
ENGINE SPEED
MODEL NO. ENDING WITH:
MODEL NO. WITHOUT EXTENSION
HIGH IDLE
3200 ± 50 RPM
NOTE: Model numbers may or may not end with an extension after the number. There are several different extensions that may be shown; i.e. EX or CE.
Example: 922222 (no extension)
922222 EX
922222 CE
922222 US
REV B 5-2 119293
DECK ADJUSTMENTS
Deck Leveling
1.
Park the mower on a hard, flat surface.
2.
Check tire pressures (8 – 12 psi) to make certain the tires are properly inflated before starting to level deck.
WARNING
Stop engine. Make sure deck clutch switch is in the down
(OFF) position. Remove ignition key. Place steering control levers in the park brake position. Make sure blades are stopped before leaving seat.
3.
Raise and place deck cutting height adjusting lever in the
Height adjusting lever
Make sure this hardware is tight
Figure 6-2
Measure to top of deck
Figure 6-1
4.
Make sure all deck hardware is tight on the right rear of
5.
Measure the right rear of the deck from the ground to the
6.
Now, go to the left rear of the deck and measure from the ground to the top of the deck. If it is different than the right hand side then the deck will need to be re-leveled.
7.
Loosen the hardware that secures the cam just enough to allow the cam to pivot. Do not over loosen the cam as it
will allow the deck to move on its own. Figure 6-5
119293 6-1
Figure 6-3
REV B
9. To allow for easier access when tightening the adjusting hardware, lower the deck to its lowest position.
Cam
3/8” drive extension
Measure to top of deck
Figure 6-6
10. Tighten the cam hardware.
IMPORTANT: When tightening the cam hardware you must tighten the inner nut while holding the bolt and outer nut to keep the cam from rotating and changing the adjustment. The inner nut must be tight to prevent cam
movement. Figure 6-7 & Figure 6-8
Bolt
Outer nut
Figure 6-4
Hardware
Cam
Figure 6-5
8.
Pivot the cam by using a 3/8” rachet and extension. Pivot the cam until the top of the deck is the same distance
from the ground as the right side. Figure 6-6
Hold the bolt and outer nut so cam does not move while tightening the inner nut.
Figure 6-7
11.
Go to the front of the deck and measure the center of the deck from the ground to the top of the deck. This distance should be 1/8” to 3/8” less than the rear corner dimensions. If it is not then it will be necessary to adjust
the deck front to back. Figure 6-9
12.
Level the front of the deck by turning the lock nut, at the front of the mower, until the correct distance from the
ground to the top of the deck is attained. Figure 6-10
REV B 6-2 119293
Lock nut
Inner nut
Tighten the inner nut to prevent slipping of the adjustment.
Figure 6-8
Front center of deck
Figure 6-10
Figure 6-9
119293 6-3 REV B
Blades
Mower blade maintenance
Refer to the Mower blade replacement section for blade removal and installation.
Check the mower blades daily as they are the key to power efficiency and well groomed turf. Keep the blades sharp. A dull blade will tear rather than cut the grass, leaving a brown ragged top on the grass within a few hours. A dull blade also requires more power from the engine.
Replace any blade which is bent, cracked or broken.
Lay the blade on a flat surface and check for distortion (Figure 6-12 & Figure 6-13). Replace any distorted blade.
Resharpening pattern
WARNING
Never attempt to straighten a bent blade by heating, or weld a cracked or broken blade as the blade may break and cause serious injury. Replace worn or damaged blades.
Do not sharpen to original pattern (below). It is easier to get a straight cutting edge following the resharpening pattern shown above.
WARNING
Never work with blades while engine is running or deck clutch switch is engaged (on). Always place deck clutch switch in the disengaged position, place steering control levers in the park brake position and turn engine off and disconnect negative battery cable. Block up mower when you must work under it. Wear gloves when handling blades. Always check for blade damage if mower strikes a rock, branch or other foreign object during mowing!
WARNING
Always wear adequate eye protection when grinding mower blades.
WARNING
Mower blades are sharp and can cut. Wrap the blade(s) or wear gloves and use extra caution when servicing them.
Sharpen the blades on a grinder following pattern as shown
(Figure 6-11). Touch-up sharpening can be done with a file
Check the blades for balance following grinding. A commercial balancing tool is available through most hardware supply stores, or balancing can be done by placing the blade on an inverted line punch or 5/8” bolt. Blade should not lean or tilt.
Spin the blade slowly, blade should not wobble. If blade is out of balance, true it up before reinstalling.
Figure 6-11
Warped Blade (Replace)
Original edge
Straight Blade
Comparison of Warped and Straight Blades
Figure 6-12
Cutting edge
Cutting Plane
Twisted Blade Edge
(replace)
Cutting edge
Straight Blade Edge
End view of blades, comparing twisted and straightened blades
Figure 6-13
Cutting plane
REV B 6-4 119293
Mower blade replacement
WARNING
This procedure will require that the mower to be raised and blocked up off of the ground. Use only appropriate vehicle stands, with a minimum weight rating of 2000 pounds to block the unit up. Use in pairs only. Follow the instructions supplied with the vehicle stands.
1.
Park the mower on a flat surface and stop the engine.
Make sure deck clutch switch is in the down (OFF) position. Remove ignition key. Place the steering control levers in the park brake position. Make sure the blades are stopped before leaving seat. Disconnect the negative battery cable.
2.
Raise the front of the unit and block with certified jack stands. This allows easier access to the blades under the deck.
3.
Install a blade lock tool (Hustler
®
part number 381442) over the two blades to prevent them from rotating.
DANGER
Never work with blades while engine is running or deck clutch is engaged. Always place deck clutch in the disengaged position, engage control levers in the park brake position and turn engine off. Block up mower when you must work under it. Wear gloves when handling blades.
Always check for blade damage if mower strikes a rock, branch or other foreign object during mowing!
when using the blade lock tool (381442) as it requires two blades to work properly.
5.
Inspect the blade for damage. If the blade is damaged, replace it. If the blade is not damaged, either sharpen it or replace it with a new blade or another sharpened used blade.
WARNING
Never attempt to straighten a bent blade by heating, or weld a cracked or broken blade as the blade may break and cause serious injury.
6.
If sharpening the blade, refer to the Mower blade
maintenance section for proper sharpening procedures.
7. The spindles have a 5/8" diameter boss that centers the blades on the spindles. When re-installing blades, ensure that the blade is centered on the boss and seated flat against the spindle shaft face.
8. When attaching the blade to the spindle shaft do not reuse spindle bolts which have stripped, worn or undercut threads. Torque bolts on spindles to 48 foot-pounds
(65.14 Nm) when reinstalling blades.
IMPORTANT: The blade sail (curved part) must be pointing upward toward the inside of the deck to ensure proper cutting.
WARNING
Rotate the blades after installation to ensure blade tips do not touch each other or sides of the mower.
DANGER
WARNING
Exercise caution when working under the deck as the mower blades are extremely sharp. Wearing gloves is advisable when working around or with the blades.
Blade lock tool
Failure to correctly torque the bolt may result in the loss of the blade which can cause serious injury.
9.
Remove the blade lock.
10.
Raise the front of the mower and remove the jack stands.
11. Lower the mower.
12.
Re-attach the negative battery cable.
Deck Belt
Blade
Blade
Figure 6-14
4.
Use a 5/8” wrench to remove the 7/16” cap screw holding the blade to the spindle shaft.
NOTE: Only remove and install one blade at a time
119293 6-5
Inspect belts frequently for wear and serviceability. Replace a belt that shows signs of severe cuts, tears, separation, weather checking and cracking, or burns caused by slipping. Slight raveling of belt covering does not indicate failure; trim ravelings with a sharp knife.
Inspect the belt pulley grooves and flanges for wear. A new belt, or one in good condition, should never run against the bottom of the groove. Replace the pulley when this is the case, otherwise, the belt will lose power and slip excessively.
Never pry a belt to get it on a pulley as this will cut or damage the fibers of the belt covering.
Keep oil and grease away from belts, and never use belt dress-
REV B
Spring mount
Tensioning
Idler spring
Boss
Spindle shaft face
Tensioning
Idler spring
Blade
Figure 6-15
ings. Any of these will destroy the belt composition in a very short time.
Deck belt adjustment
The spindle belt tension remains constant by means of a tension idler and spring. There is no tension adjustment of this belt.
Figure 6-16 & Figure 6-17
Spring mount
Figure 6-17
Figure 6-16
Deck belt replacement
WARNING
Allow the engine and muffler to cool before proceeding with the following procedure.
WARNING
Exercise caution when releasing spring tension from the belt idler.
1. Park the mower on a flat surface and stop the engine.
Make sure deck clutch switch is in the down (OFF) position. Remove ignition key. Place the steering control levers in the park brake position. Make sure the blades are stopped before leaving seat. Disconnect the negative battery cable.
2. Lower the deck to the lowest setting.
3. Remove the deck covers. Figure 6-18 & Figure 6-19
4. Using a tension spring hook (Hustler part number
604462) disconnect the tension idler spring from the spring mount to release tension from the deck drive belt.
Figure 6-16, Figure 6-17 & Figure 6-18
NOTE: The spring and spring mount will become loose and can become misplaced. Set these aside after removal for easier access upon re-assembly.
5. Remove the deck drive belt from the deck spindle pulleys and idler pulley.
6. Remove the deck drive belt from the electric clutch pulley located on the engine shaft.
7. Route the new deck drive belt around the clutch pulley, spindle pulleys and stationary idler pulley. Make certain the belt is routed properly. Figure 6-21, Figure 6-22, &
REV B 6-6 119293
Tension idler spring
Deck cover
Figure 6-18
Deck cover
Spring mount
Tension spring hook (604462)
Figure 6-20
WARNING
Never operate the mower without the deck covers in place.
Deck cover
Deck cover
Figure 6-19
8.
Using the tension spring hook (604462), re-tension the deck drive belt by pulling on the deck belt idler spring and hooking it in the spring mount on the deck.
9.
Re-install the deck covers. Figure 6-18 & Figure 6-19
Deck drive belt
Figure 6-21
Electric clutch pulley
119293 6-7 REV B
NOTE:
The following notes are the same for the different decks shown.
1. There is no tension adjustment of this belt
2.
Route belt as shown.
36”/42" Deck Belt Routing
52" Deck Belt Routing
Figure 6-22
REV B
Figure 6-23
6-8 119293
Electrical Schematic — Kawasaki
ELECTRICAL
119293 7-1 REV B
REV B 7-2 119293
MAINTENANCE
Maintenance Schedule
Refer to Figure 8-1, Figure 8-2,
Figure 8-3, Figure 8-4, & Figure 8-5
SERVICE AT
INTERVALS INDICATED
Verify safety start interlock system
Visually inspect unit for loose hardware and/or damaged parts
Visually inspect tires
Check oil level, engine (1)
Clean air intake screen (4)
Check fuel level
Blades - sharpen & securely fastened
Discharge chute - securely in place & in lowest position
Check tire pressure with a gauge
Clean engine and transaxle compartment
Grease gauge wheel bearings
Change engine oil & filter (1)(3)
Check battery connections
Clean engine exterior (a)
Replace air cleaner paper element (4)
Check pump & deck belt tension and condition (5)
Check fuel system (6)
Check fuel tank grommet (6)
Tighten lug nuts on wheels (2)
Change fuel filter (6)
Replace fuel evaporation system filter (7)
WEEKLY
OR 40
HOURS
ANNUALLY
OR 100
HOURS
Prior to each use
Prior to each use
Prior to each use
Prior to each use or every 4 hours
Prior to each use or every 4 hours
Prior to each use
Prior to each use
Prior to each use
Prior to each use
After each use
X
X
X
X
X
X
X
X
X
X
X
NOTES:
1.
Initial oil change is after 5 hours of operation. Thereafter, change oil after every 40 hours operation. Change more often under dusty or dirty conditions and during hot weather periods.
2.
Torque initially and after first 2 hours of operation.
3.
Change engine oil filter per the engine manufacturer’s recommendations. Refer to Engine Owner’s Manual for recommendations and other maintenance items..
4.
Service more often under dusty or dirty conditions.
5.
Pump drive belt only - Inspect every month and replace if worn or cracking is noticed. Otherwise, replace every 2 years.
6.
Check fuel system for any crack or leaks including, but not limit to, fuel line hoses, fuel valve, vent line hoses, vent valve, vapor valve, carbon canister, and grommets. Replace as needed.
7.
More often under dusty or dirty conditions and during hot weather.
REFERENCES:
A. Refer to engine owner’s manual for engine service information.
NOTE: After completing maintenance cycle (100 hours), repeat cycle.
119293 8-1 REV B
Maintenance Locator Chart
9
2
6
5
8
11
3
Figure 8-1
13
9
4
7
1
Figure 8-2
10
8
13
Figure 8-3
36”/42” Deck
12
1. Engine Oil Fill & Dipstick
2. Fuel Filter
3. Engine Air Cleaner
4. Engine Oil Drain Valve
5. Battery
6. Fuel Tank
7. Engine Oil Filter
8. Park Brake Switch (2)
9. Drive Tire
10. Pump Belt
11. Engine Air Intake Screen
12. Front Wheel Tires
13. Front Wheel Zerks (2)
14. Deck Belt
15. Blades
16. Fuel Evaporation System Filter
52” Deck
15
Figure 8-4
15
15
14
15
14
REV B
Figure 8-5
8-2
16
119293
SYMPTOMS PROBABLE CAUSES
SUGGESTED
REMEDIES
Starting motor does not crank
The engine will not start, starts hard or fails to keep running
Steering control levers not in park brake position or switch not adjusted
Deck clutch switch engaged
Weak or dead battery
Electrical connections are corroded or loose
15 amp fuse is blown
For additional causes
No fuel or line plugged
There is incorrect fuel in the fuel system
There is dirt in the fuel filter
Dirt, water or stale fuel in the fuel system
The choke is not on
Place steering control levers in park brake position or re-adjust switch
Disengage clutch switch
Recharge or replace
Check the electrical connections
Replace the 15 amp fuse
See engine manual
Fill tank or replace line (See
Fuel System section for more details)
Drain the tank and replace the fuel with the proper type
Replace the fuel filter
Contact your Dealer
Move the choke lever to
ON
See engine manual
See engine manual
Numerous
Numerous Engine:
Runs with continuous misfiring or engine runs unevenly or erratically
Loss of power or system will not operate in either direction
Air cooled engine overheating
Low engine oil pressure
Restrictions in air cleaner
Poor compression
Steering linkage needs adjustment
Tow valve open
The traction drive belt is worn, loose or broken
For additional causes
Air intake screen or cooling fins clogged
For additional causes
Low oil level
Oil diluted or too light
High oil consumption
Mower jerky when starting or operates in one direction only
Failed oil pump
Numerous
Steering control linkage needs adjustment
Loose steering linkage
Transaxle component faulty
Service air cleaner
Contact your Dealer
Adjust linkage
Close tow valve
Install a new traction drive belt
See engine manual
Clean screen and fins
See engine manual
Add oil
Change oil and check for source of contamination
Contact your Dealer
Contact your Dealer
Adjust linkage
Tighten linkage
Contact your Dealer
TROUBLESHOOTING
SYMPTOMS PROBABLE CAUSES
SUGGESTED
REMEDIES
Mower creeps when steering control levers are in neutral
Mower circles or veers in one direction
Mower creeps when parking brake engaged
There is abnormal vibration
Blades do not rotate
Uneven cutting height
Steering linkage needs adjustment
Adjust linkage
Steering linkage needs adjustment
Loose steering linkage
Tires improperly inflated
Transaxle component faulty
Steering linkage out of adjustment
Brakes need adjustment
The engine mounting bolts are loose
The engine pulley, idler pulley or blade pulley is loose
The engine pulley is damaged
The cutting blade(s) is/are bent or unbalanced
A blade mounting bolt is loose
Spindle bearing is worn or loose
A blade spindle is bent
The deck drive belt is worn, loose or broken
The deck drive belt is off the pulley
Electric clutch is not engaging
The blade(s) are not sharp
A cutting blade(s) is/are bent
The deck is not level
Adjust linkage
Tighten linkage
Adjust air pressure to 8 - 12 psi (55 - 83 KPa)
Contact your Dealer
Adjust steering linkage
Adjust parking brakes
Tighten the engine mounting bolts
Tighten the appropriate pulley
Contact your Dealer
Install new cutting blade(s)
Tighten the blade mounting bolt
Replace or tighten spindle bearing
Contact your Dealer
Install a new deck drive belt
Install the deck drive belt and check for a reason
Check and/or replace 15 amp fuse.
Contact your Dealer
Sharpen the blades
Install new cutting blade(s)
An anti-scalp wheel is not set correctly
The underside of the deck is dirty
Tires improperly inflated
A blade spindle is bent
Level the deck per the
Deck leveling section of the
General Service Manual
Adjust the height of the anti-scalp wheel
Clean the underside of the deck
Adjust air pressure to 8 - 12 psi (55 - 83 KPa)
Contact your Dealer
119293 9-1 REV B
REV B 9-2 119293
INDEX
PAGE
Belt adjustment ........................................................4-4
Belt replacement......................................................4-4
Blades.......................................................................6-4
Control lever stops adjustment ...............................4-2
Deck belt ..................................................................6-5
Deck belt adjustment...............................................6-6
Deck belt replacement ............................................6-6
Deck Belt Routing ....................................................6-8
Deck leveling............................................................6-1
Electrical Schematic ................................................7-1
Engine air filter.........................................................5-1
Engine oil and filter..................................................5-1
Engine RPM settings ...............................................5-2
General engine maintenance..................................5-1
General maintenance precautions .........................2-2
Maintenance introduction........................................1-1
Maintenance locator chart ......................................8-2
PAGE
Maintenance precautions ........................................2-2
Maintenance Schedule ............................................8-1
Mower blade replacement .......................................6-5
Operate machine safely ..........................................2-2
Operation Precautions.............................................2-2
Park brake spring adjustment .................................4-3
Pre-operation precautions.......................................2-1
Safe servicing practices ..........................................2-1
Service Program ......................................................1-1
Special torques ........................................................3-1
Standard torques .....................................................3-1
Steering adjustments...............................................4-1
Steering control lever neutral adjustment ..............4-1
Tires ..........................................................................4-6
Transaxle Belt Adjustment ......................................4-3
Warranty ...................................................................1-1
119293 i-1 REV B
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement