BUFFALO FDI-09101695-0 WirelessAC1300 / N900 Gigabit Dual Band Router User Manual
Add to My manuals135 Pages
advertisement
User Manual
Wireless AC1300 / N900 Gigabit Dual Band Router
WZR-D1800H
www.buffalotech.com
Contents
Chapter 1 - Product Overview .........................................5
Package Contents ................................................................... 5
Hardware Overview ................................................................. 6
Front Panel LEDs ........................................................................... 6
Back Panel ..................................................................................... 8
Right Side ...................................................................................... 10
Vertical Placement .................................................................. 11
Horizontal Placement .............................................................. 11
Wall-Mounting ......................................................................... 12
Chapter 2 - Installation .....................................................13
Initial Setup ............................................................................. 13
Chapter 3 - Configuration ................................................16
Accessing the Web-based Configuration Interface ................. 16
Configuration Interface Menus in Router Mode ...................... 18
Configuration Interface Menus in Bridge Mode ....................... 20
Setup ....................................................................................... 22
Internet/LAN (LAN Config) ...................................................... 24
Internet (Router Mode only) ........................................................... 24
PPPoE (Router Mode only) ............................................................ 25
DDNS (Router Mode only) ............................................................. 28
VPN server (Router Mode Only) .................................................... 30
DHCP Lease (Router Mode only) .................................................. 34
NAT (Router Mode only) ................................................................ 35
- 1 -
Wireless Config ....................................................................... 37
Advanced ....................................................................................... 41
MAC Filter ...................................................................................... 44
Multicast Control ............................................................................ 45
Security (Router Mode only) ................................................... 47
Firewall (Router Mode only) ........................................................... 47
IP Filter (Router Mode only) ........................................................... 49
VPN Passthrough (Router Mode only) ........................................... 50
LAN Config .............................................................................. 51
Port Forwarding (Router Mode only) .............................................. 51
DMZ (Router Mode only) ............................................................... 52
UPnP (Router Mode only) .............................................................. 53
QoS (Router Mode only) ................................................................ 54
NAS ......................................................................................... 55
Disk management .......................................................................... 55
Shared Folder ................................................................................ 57
User Management ......................................................................... 59
Shared Service .............................................................................. 60
Web Access ................................................................................... 61
Media Server .................................................................................. 63
Admin Config ........................................................................... 66
Password ....................................................................................... 67
Time/Date ...................................................................................... 68
Network-USB ................................................................................. 71
- 2 -
Save/Restore ................................................................................. 74
Initialize/Restart ............................................................................. 75
Diagnostic ............................................................................... 78
System Info .................................................................................... 78
Packet Info ..................................................................................... 81
Client Monitor ................................................................................. 82
Chapter 4 - Connect to a Wireless Network ...................84
Automatic Secure Setup (AOSS / WPS) ................................. 84
Windows 7/Vista (Client Manager V) ............................................. 85
Windows XP (Client Manager 3) .................................................... 86
Mac OS X (AOSS Assistant) .......................................................... 87
Other Devices (e.g. Game Console) .............................................. 88
Manual Setup .......................................................................... 88
Windows 7 (WLAN AutoConfig) ..................................................... 88
Windows Vista (WLAN AutoConfig) ............................................... 89
Windows XP (Wireless Zero Configuration) ................................... 92
Mac OS X (Wi-Fi) ........................................................................... 93
Chapter 5 - Troubleshooting ............................................94
Cannot connect to the Internet over wired connection. ........... 94
Cannot access the web-based configuration Interface. .......... 94
Cannot connect to the network wirelessly. .............................. 95
You forgot AirStation's SSID, Encryption Key, or Password. ... 95
Restoring the Default Configuration ........................................ 95
TCP/IP Settings (Windows 7) .................................................. 96
TCP/IP Settings (Windows Vista) ............................................ 97
TCP/IP Settings (Windows XP) ............................................... 98
- 3 -
TCP/IP Settings (Mac OS X) ................................................... 99
Other Tips ................................................................................ 100
Chapter 6 - Default Configuration Settings ....................102
Chapter 7 - Network-USB Navigator ...............................109
Initial Setup for Windows Users .............................................. 109
Initial Setup for Mac Users ...................................................... 114
Opening the Network-USB User Manual ................................ 117
How to use Network-USB ....................................................... 118
Chapter 8 - Checking Wireless Signal Quality ...............119
Windows 7/Vista ...................................................................... 119
Mac OS X ................................................................................ 120
Chapter 9 - Shared Folders and the USB Port ...............122
- 4 -
Chapter 1 - Product Overview
Package Contents
The following items are included in your AirStation package. If any of the items are missing, please contact your vender.
• WZR-D1800H ................................................................................................................................ 1
• AirStation Setup Card ................................................................................................................ 1
• AC adapter ..................................................................................................................................... 1
• Stands .............................................................................................................................................. 2
• Screws for wall-mounting ........................................................................................................ 2
• LAN cable ....................................................................................................................................... 1
• AirNavigator CD ........................................................................................................................... 1
• Quick Setup Guide ...................................................................................................................... 1
• Warranty Statement ................................................................................................................... 1
- 5 -
1
3
Chapter 1 Product Overview
Hardware Overview
Front Panel LEDs
2
4
5
1
AOSS button To initiate AOSS, hold down this button until the Wireless LED flashes
(about 1 second). Then, push or click the AOSS button on your wireless client device to complete the connection. Both devices must be powered on for this to work.
2
Wireless LED (Blue or Amber)
On: Wireless LAN is enabled.
Randomly blinking: Wireless LAN is transmitting.
2 blinks: AirStation is waiting for an AOSS or WPS security key.
Continuously blinking:
Off:
AOSS/WPS error; failed to exchange security keys.
Wireless LAN is disabled.
Note:
Wireless LED is blue : Security settings have been made for the wireless LAN.
Wireless LED is amber : Security settings have not been made for the wireless LAN.
- 6 -
Chapter 1 Product Overview
3 Internet access LED (Blue)
On:
Off:
Internet access is available.
Internet access is not available.
4 Router LED (Blue)
On:
Off:
Router functionality is enabled.
Router functionality is disabled.
5
Buffalo LED (White or Red)
On (White):
Off:
On (Red) *1 :
2 blinks (Red) *2 :
3 blinks (Red) *2 :
4 blinks (Red) *2 :
5 blinks (Red) *3 :
9 blinks (Red) *2 :
Continuously blinking *1 :
Power is on.
Power is off.
Booting.
Flash ROM error.
Wired Ethernet LAN error.
Wireless LAN error.
IP address setting error.
System error.
Updating firmware, saving settings, or initializing settings.
*1 Never unplug the AC adapter while the Buffalo LED is blinking continuously.
*2 Turn off AirStation first, wait for a few seconds, then turn it back on.
*3 Because the network addresses of both the Internet port (WAN port) and the LAN port are the same, it is not possible to establish communication. Change the LAN side IP address of the
AirStation.
- 7 -
10
11
14
Chapter 1 Product Overview
Back Panel
6
8
7
9
12
13
15
6 Router button This button turns the router on and off. The operation mode is changed by holding down the button.
7 USB LED (Blue)
On:
Blinking:
The USB drive is connected.
The USB drive can be removed.
Note: When this LED is blinking, the connected USB drive cannot be used. Remove the connected USB drive. If the LED continues to blink even after the USB drive is removed, restart the AirStation. Do not remove the USB drive or turn off the AirStation while the USB LED is on.
8 USB Eject button To dismount a USB hard drive, hold down this button until the USB LED flashes (about 3 seconds). The USB drive can then be unplugged safely.
9
USB Port Connect the USB drive.
- 8 -
Chapter 1 Product Overview
10 LAN Port Connect your computer, hub, or other Ethernet devices to these ports.
This switching hub supports 10 Mbps,100 Mbps, and 1000 Mbps connections.
11 Internet Port 10 Mbps, 100 Mbps, and 1000 Mbps connections are supported.
Note: In bridge/AP mode (router off), the Internet port becomes a regular LAN port, for a total of 5 usable LAN ports.
12 LAN LED (Green)
On:
Blinking:
An Ethernet device is connected.
An Ethernet device is communicating.
13 Internet LED (Green)
On:
Blinking:
The Internet port is connected.
The Internet port is transmitting data.
14 Power button
15 DC connector
This button turns the power on and off.
Connect the included AC adapter here.
Bottom
16
17
16 Reset button To reset all settings, hold down this button until the Buffalo LED turns red
(about 3 seconds). The power must be on for this to work.
17 Setup card slot This is the slot where the AirStation setup card is stored. The initial settings for the username, password, SSID, and encryption type are provided on the card for logging into the configuration interface.
- 9 -
Chapter 1 Product Overview
Right Side
18
18
Mounting holes Mounting holes are provided for mounting the AirStation to a wall. Use the supplied screws in the holes to mount to a wall.
- 10 -
Chapter 1 Product Overview
Vertical Placement
Attach the stand as shown in the figure below.
Stand
Stand
Horizontal Placement
The same stand also allows horizontal placement. Install the stand as shown in the figure below.
Stand
- 11 -
Chapter 1 Product Overview
Wall-Mounting
Install with the supplied screws in the mounting holes of the AirStation as shown in the figure below.
85 mm (3.35 in.)
Mounting holes
Screws
50 mm (1.97 in.)
- 12 -
Chapter 2 - Installation
Initial Setup
To configure your AirStation, follow the procedure below.
1
Verify that you can connect to the internet without the AirStation, then turn off your modem and computer.
2 disconnect
Unplug the LAN cable which connects your computer and modem.
modem computer
3
Plug one end of the LAN cable into your modem and the other end to the AirStation’s
Internet (WAN) port. Turn on the modem. modem
1) connect
LAN cable
2) connect
Internet port
AirStation
- 13 -
Chapter 2 Installation
4
Turn on the AirStation, then wait one minute.
AirStation
Note : If the power does not turn on even when the AC adapter is connected, press the Power button on the rear of the AirStation.
Connect the power supply power outlet
5
If using a wired LAN, connect the AirStation LAN port and computer using a LAN cable.
If using a wireless LAN, connect the computer to the wireless LAN by referring to Chapter 4.
AirStation
1) connect
LAN cable
2) connect computer
6
Once your computer has booted, the AirStation’s LEDs should be lit as described below:
Wireless On or blinking.
Internet access On.
Router
Buffalo
LAN
On.
White light on.
Green light on or blinking.
Internet Green light on or blinking.
For LED locations, refer to chapter 1.
Note: If the router LED is not lit, hold down the router button for about 3 seconds to switch to router mode.
- 14 -
Chapter 2 Installation
7
Launch a web browser. If the home screen is displayed, setup is complete.
If username and password fields are displayed, enter “admin” for the username and
“password” for the password, then click [OK]. Step through the wizard to complete setup.
You’ve completed the initial setup of your AirStation. Refer to Chapter 3 for advanced settings.
- 15 -
Chapter 3 - Configuration
1
2
The web-based configuration tool lets you change advanced settings for the AirStation. Don’t change these settings unless you know what you’re doing.
Accessing the Web-based Configuration Interface
To configure the AirStation’s advanced settings manually, log in to the web-based configuration interface as shown below.
Launch a web browser.
Enter the AirStation’s LAN-side IP address in the address field and press the Enter key.
3
Note: The AirStation’s default LAN-side IP address depends on the mode.
In router mode: 192.168.11.1
In bridge mode: 192.168.11.100
If you changed the IP address of the AirStation, then use the new IP address.
Enter “admin” for the username and “password” for the password and click [OK].
Note: If you forget your password, hold down the
Reset button (page 9) to initialize all settings.
Note that all other settings will also revert to their default values.
- 16 -
Chapter 3 Configuration
4 This is the configuration interface, where most
AirStation settings can be configured.
Help is always displayed on the right side of each screen.
Refer to the help screens for more information on using the configuration interface.
- 17 -
Chapter 3 Configuration
Configuration Interface Menus in Router Mode
The menu structure for the AirStation in router mode is as follows. Please refer to the pages listed at right for explanations of each item.
Main screen
Internet/LAN
Internet
PPPoE
DDNS
VPN Server
LAN
DHCP Lease
NAT
Route
Wireless Config
WPS
Basic
Advanced
WMM
MAC Filter
Multicast Control
AOSS
Security
Firewall
IP Filter
VPN
Passthrough
LAN Config
Port Forwarding
DMZ
UPnP
QoS
Descriptions
Configure Internet side port and settings.
PPPoE settings (DSL login).
DNS settings.
VPN server settings.
LAN side port configuration.
DHCP lease settings.
Network address translation settings, used to connect LAN side devices to the Internet.
Configure the AirStation’s IP communication route.
WPS settings and status.
Configure basic wireless settings.
Configure advanced wireless settings.
Set priorities for Wireless Multimedia Extensions (Wi-Fi Multimedia).
Limit access to specific devices.
Configure limits on sending unnecessary multicast packets to the wireless LAN port.
AOSS (AirStation One-touch Secure System) settings and status.
Configure port translation and exceptions for games and other programs.
Configure a destination to transfer communication packets without a
LAN side destination.
Configure UPnP (Universal Plug and Play).
Configure priority for packets that require a guaranteed data flow.
- 18 -
Page
Protect your computer from outside intruders.
IP filters for packets passing through the LAN side and the Internet side.
Configure IPv6 passthrough, PPPoE passthrough, and PPTP passthrough. Page 50
Chapter 3 Configuration
NAS
Disk Management View the status and configure of attached USB disks.
Shared Folder Set the USB disk to use as shared folders.
User Management Configure users to access shared folders.
Shared Service
Web Access
Media Server
Configure shared folder access.
Configure Web Access.
Configure a Media Server.
Configure a BitTorrent client.
BitTorrent
Admin Config
Name
Password
Time/Date
NTP
ECO
Configure the AirStation’s name.
Configure the AirStation’s login password for access to the configuration interface.
Configure the AirStation’s internal clock.
Configure the AirStation to synchronize with an NTP server to automatically set the AirStation’s internal clock.
Configure the AirStation’s ECO Mode.
Network-USB
Access
Configure Network-USB from this screen.
Configure access restrictions to the AirStation’s configuration interface.
Log
Save/Restore
Initialize/Restart
Update
Diagnostic
Configure a syslog server to manage the AirStation’s logs.
Save or restore the AirStation’s configuration from a configuration file.
Initialize the AirStation or reboot it.
Update the AirStation’s firmware.
System Info
Logs
Packet Info
Client Monitor
View current system information for the AirStation.
Check the AirStation’s logs.
View all packets transferred by the AirStation.
View all devices currently connected to the AirStation.
Test the AirStation’s connection to other devices on the network.
Ping
Logout
Click this to log out of the AirStation’s configuration interface.
- 19 -
Chapter 3 Configuration
Configuration Interface Menus in Bridge Mode
The menu structure in bridge mode is as follows. Please refer to the pages listed at right for explanations of each item.
Main screen
LAN Config
LAN
Descriptions
Route
Wireless Config
WPS
Basic
Advanced
WMM
MAC Filter
Multicast Control
LAN side port configuration.
Configure the AirStation’s IP communication route.
WPS settings and status.
Configure basic wireless settings.
Configure advanced wireless settings.
Set priorities for Wireless Multimedia Extensions (Wi-Fi Multimedia).
Limit access to specific devices.
Configure limits on sending unnecessary multicast packets to the wireless LAN port.
AOSS (AirStation One-touch Secure System) settings and status.
AOSS
NAS
Disk Management View the status and configure of attached USB disks.
Shared Folder Set the USB disk to use as shared folders.
User Management Configure users to access shared folders.
Shared Service
Web Access
Media Server
BitTorrent
Admin Config
Configure shared folder access.
Configure Web Access.
Configure a Media Server.
Configure a BitTorrent client.
Name
Password
Time/Date
NTP
ECO
Configure the AirStation’s name.
Configure the AirStation’s login password for access to the configuration interface.
Configure the AirStation’s internal clock.
Configure the AirStation to synchronize with an NTP server to automatically set the AirStation’s internal clock.
Configure the AirStation’s ECO Mode.
Network-USB
Access
Page
Configure Network-USB from this screen.
Configure access restrictions to the AirStation’s configuration interface.
- 20 -
Chapter 3 Configuration
Log
Save/Restore
Initialize/Restart
Update
Diagnostic
System Info
Logs
Configure a syslog server to manage the AirStation’s logs.
Save or restore the AirStation’s configuration from a configuration file.
Initialize the AirStation or reboot it.
Update the AirStation’s firmware.
View current system information for the AirStation.
Check the AirStation’s logs.
Packet Info
Client Monitor
Ping
Logout
View all packets transferred by the AirStation.
View all devices currently connected to the AirStation.
Test the AirStation’s connection to other devices on the network.
Click this to log out of the AirStation’s configuration interface.
- 21 -
Chapter 3 Configuration
Setup
Setup is the home page of the configuration interface. You can verify settings and the status of the
AirStation here.
Parameter
Internet/LAN (LAN Config)
Wireless Config
Security
Meaning
Displays the configuration screen for the Internet port and LAN ports.
Click this button to display the configuration screen for wireless settings.
Click this button to display the configuration screen for security.
- 22 -
Chapter 3 Configuration
Parameter
LAN Config
NAS
Admin Config
Diagnostic
Easy Setup
MODE Information
Internet Information
Check Connection
Refresh
WIRELESS
AOSS Setup
WPS Setup
ECO Mode
Network Service List
Media Server
Download List
Language
Logout
Meaning
Click this button to display the configuration screen to open ports for games and applications.
Click this button to display the configuration screen for NAS settings.
Click this button to display the configuration screen for administration settings.
Click this button to display the status of the AirStation.
Enables you to easily configure the AirStation’s network settings automatically.
This indicates the operation mode of the AirStation.
Displays WAN-side system information for the AirStation.
Click this button to check if the AirStation is connected to the
Internet properly.
Click this button to refresh the current screen.
Displays the current wireless settings.
Click this button to display the AOSS configuration screen.
Click this button to display the WPS configuration screen.
This indicates the operating status of ECO Mode.
Displays the list of the network devices for which information is provided from the network on the LAN-side.
Displays the status of the media server.
Displays the list of BitTorrent files downloading.
Enables you to select the language you use.
Log out of the configuration interface. If the AirStation does not communicate for 5 minutes, it will log out automatically.
- 23 -
Chapter 3 Configuration
Internet/LAN (LAN Config)
Internet (Router Mode only)
Configure the WAN-side port (“Internet port”).
Parameter
Method of Acquiring IP Address
Default Gateway
DNS Name Server Address
Internet MAC Address
MTU size of Internet Port
Meaning
Specify how the WAN-side IP address is obtained.
Configure an IP address for the default gateway.
Specify an IP address for the DNS server.
Configure the Internet side MAC address.
Note: Configuring an improper MAC address may make the AirStation unusable. Change this setting at your own risk.
Configure the MTU value of the Internet port. Values of 578 to 1500 bytes may be entered.
- 24 -
Chapter 3 Configuration
PPPoE (Router Mode only)
Configure PPPoE settings.
Parameter
Default PPPoE Connection
IP Unnumbered PPPoE Connection
PPPoE Connection List
[Edit Connection List]
Meaning
If you have registered multiple connection destinations in the
PPPoE Connection List, connection destinations selected here have priority. You need to configure the route to which PPPoE is connected to if you don’t use the default settings.
Select the destination from the PPPoE Connection List which is used when “Use IP Unnumbered” is chosen for the Method of
Acquiring IP Address (page 24).
Edit PPPoE destination. You can register up to 5 sessions.
Click this button to edit destination settings.
- 25 -
Chapter 3 Configuration
Parameter
PPPoE Connection No.*-Add
Meaning
This is displayed when [Edit Connection List] is clicked.
Name of Connection
Enter the name to identify the connected destination. You may enter up to 32 alphanumerical characters and symbols.
Username
Enter the username specified by your ISP for PPPoE certification.
You may enter up to 32 alphanumerical characters and symbols.
Password
Enter the password specified by your ISP for PPPoE certification.
You may enter up to 32 alphanumerical characters and symbols.
Service Name
Fill in this field only if your ISP specifies a Service Name. Leave blank otherwise. You may enter up to 32 alphanumerical characters and symbols.
Connection Type
Specifies the timing for the AirStation to connect to your provider.
Automatic disconnection
Set time to disconnect after communication is stopped when the connection method is set to [Connection on Demand] or
[Manual]. You can enter up to 1440 minutes.
Authorization
Configure an authorization method with a provider.
MTU Size
Configure the MTU size for PPPoE. Values of 578 to 1500 bytes may be entered.
MRU Size
Configure MRU (Maximum Receive Unit) for PPPoE. Values of 578 to 1492 may be entered.
- 26 -
Chapter 3 Configuration
Parameter
PPPoE Connection No. *-Add
Preferred Connections
[Edit Preferred Connections]
Preferred PPPoE Connection -Add
Meaning
Keep Alive
If Keep Alive is enabled, then the AirStation will issue an LCP echo request once a minute in order to maintain the connection with the PPPoE. If the server does not respond for more than
6 minutes, the line is recognized as disconnected and the
AirStation will terminate the connection. [Disabled] is the recommended setting.
Displays information you have set regarding to the connection destination route.
Click to edit the connection destination route settings.
Click [Edit Preferred Connections] to display.
Name
The destination to connect by PPPoE if [Destination address] and
[Source address] match. Select the destination registered to the
PPPoE Connection List.
Destination address
When communicating to this address, the AirStation will communicate with [Name of Connection.]
Source address
When communicating from this address, the AirStation will communicate with [Name of Connection.]
- 27 -
Chapter 3 Configuration
DDNS (Router Mode only)
Configure Dynamic DNS settings. Many settings are only available when the appropriate Dynamic
DNS service is enabled.
Parameter
Dynamic DNS Service
Username
Password
Hostname
Email Address
TZO Key
Domain Name
Meaning
Select a provider (DynDNS or TZO) for Dynamic DNS.
Enter the Dynamic DNS username. You may enter up to 64 alphanumerical characters and symbols.
Enter the Dynamic DNS password. You may enter up to 64 alphanumerical characters and symbols.
Enter the Dynamic DNS hostname. You may enter up to 255 alphanumerical characters, hyphens, and periods.
Enter the email address which is registered to the Dynamic DNS service. You may enter up to 64 alphanumerical characters and symbols.
Enter the TZO Key which is registered to the Dynamic DNS service.
You may enter up to 64 alphanumerical characters and symbols.
Enter the domain name which is registered to the Dynamic DNS service. You may enter up to 255 alphanumerical characters, hyphens, and periods.
- 28 -
Chapter 3 Configuration
Parameter
IP Address Update Period
Internet Side IP Address
Domain Name
Status
Meaning
Specifies the period to notify the dynamic DNS service provider of the current IP address. For DynDNS, set it between 0 and 35 days.
For TZO, set it between 0 and 99 days. If 0 (zero) days is set, no periodic update is performed.
The WAN-side IP address of the AirStation’s Internet port. This address is sent to the dynamic DNS service provider.
The domain name assigned by the dynamic DNS Service provider.
The AirStation can be accessed from the Internet using this domain name.
Display the status of dynamic DNS service.
- 29 -
Chapter 3 Configuration
VPN server (Router Mode Only)
Configure the VPN server.
- 30 -
Chapter 3 Configuration
Parameter
Auto Input
LAN Side IP Address
DHCP Server Function
DHCP IP Address Pool
PPTP Server Function
Authorization Type
Server IP Address
Client IP Address
DNS Server IP Address
WINS Server IP Address
[Edit PPTP User List]
Username
Password
Method of Acquiring IP Address
PPTP User List
Meaning
Click to generate a random IP address.
Set a LAN side IP address and subnet mask.
Enable or disable the DHCP server, which assigns IP addresses automatically.
Configure the range of IP addresses to be assigned by the DHCP server and IP addresses to be excluded from that range. Values from 0-253 may be entered.
Enable to use a PPTP server.
Select the authentication method for PPTP connection.
Select the server IP address.
Select the IP address range.
Choose the IP address for the DHCP server.
Choose the IP address for the WINS server.
Click to edit user information.
Enter the username to connect to the PPTP server. You may enter up to 16 alphanumerical characters and symbols.
Enter the password to connect to the PPTP server. You may enter up to 16 alphanumerical characters and symbols.
Select the method to be used to assign the IP address is assigned to the PPTP client.
Displays the PPTP connection user information.
- 31 -
Chapter 3 Configuration
LAN
Configure LAN-side and DHCP Server settings.
Parameter
LAN Side IP Address
DHCP Server Function
DHCP IP Address Pool
LAN Side IP Address
(For IP Unnumbered)
Advanced Settings
Lease Period
Default Gateway
Meaning
By default, the LAN side IP address is 192.168.11.1 with subnet mask 255.255.255.0. You may change it here.
Enable or disable the DHCP server, which assigns LAN-side IP addresses automatically.
Configure the range of IP addresses to be assigned by the DHCP server and IP addresses to be excluded from that range. Values from 0-253 may be entered.
Set an IP unnumbered LAN side IP address.
Note: A PC with a normal LAN side IP address and a PC with an IP
Unnumbered IP address cannot communicate each other.
Check [Display] to display DHCP server advanced settings options.
Set the effective period of an IP address assigned by the DHCP server. Up to 999 hours may be entered.
Set the default gateway IP address for the DHCP server to issue to clients.
- 32 -
Chapter 3 Configuration
Parameter
DNS Servers
Router mode only
WINS Server
Router mode only
Domain Name
Router mode only
Default Gateway
Bridge mode only
DNS Server Address
Bridge mode only
Meaning
Set the DNS server IP address for the DHCP server to issue to clients.
Set the WINS server IP address for the DHCP server to issue to clients.
Set the domain name for the DHCP server to issue to clients. You may enter up to 127 alphanumerical characters, hyphens, and periods.
Set the default gateway IP address.
Set the DNS server IP address.
- 33 -
Chapter 3 Configuration
DHCP Lease (Router Mode only)
Configure DHCP Exceptions.
Parameter
IP Address
MAC Address
Current DHCP Client Information
Meaning
Enter an IP address to lease manually. The IP address should be from the same subnet as the DHCP scope, but not be within the range that DHCP is assigning to other devices.
Enter the MAC address which identifies the client.
Displays information for current leases. An IP address which is leased automatically can be changed to manual leasing by clicking
[Manual Assignment].
- 34 -
Chapter 3 Configuration
NAT (Router Mode only)
Configure network address translation settings. This enables LAN-side devices to communicate with the Internet.
Parameter
Address Translation
Log Output of Deleted Packets
Meaning
Enable to use Network Address Translation.
Enable to log deleted packets (such as errors) during address translation.
- 35 -
Chapter 3 Configuration
Route
Configure the AirStation’s IP communication route.
Parameter
Destination Address
Gateway
Metric
Routing Information
Meaning
Adds a destination IP address and subnet mask to a routing table.
Adds a gateway address to a routing table.
The metric is the maximum number of router hops a packet may take on the way to its destination address. Values between 1 and 15 may be entered. The default value is 15.
Manual entries will appear here after being added.
- 36 -
Chapter 3 Configuration
Wireless Config
WPS
WPS Status and Settings.
Parameter
WPS
External Registrar
AirStation PIN
Enrollee PIN
WPS status
Meaning
Enable to use WPS automatic configuration.
Enable to accept configure requests from other WPS devices.
Note: Configure requests will not be accepted if AOSS is in use.
Displays the PIN code of the AirStation. Clicking [Generate PIN] will generate a new PIN code. This code can be entered into other wireless devices that support WPS.
Enter the PIN code for the other wireless device and click [OK].
Displays “configured” if all available wireless bands are configured. Displays “unconfigured” if at least one wireless band is unconfigured.
- 37 -
Chapter 3 Configuration
Basic
Configure basic wireless settings from here.
Parameter
Wireless Radio
SSID
Wireless Channel
High-Throughput Mode
Broadcast SSID
Meaning
Determines whether to allow wireless communication. If this is unchecked, then no wireless connections will be allowed.
The SSID may contain 1 - 32 alphanumeric characters.
Sets a channel (a range of frequencies) for wireless connections.
With Auto Channel selected, the AirStation will automatically use the best available channel.
High-throughput mode uses triple the normal frequency range,
80 MHz instead of 20 MHz. In uncongested areas this can increase performance. To use High-throughput mode, set the Bandwidth to
80 MHz and choose an Extension Channel.
Note: If Auto Channel is selected, then the Extension Channel is set automatically.
If [Allow] is checked, then the AirStation will respond to SSID searches from wireless devices by broadcasting its SSID. If [Allow] is unchecked, then the AirStation ignores SSID searches from wireless devices.
- 38 -
Chapter 3 Configuration
Parameter
Wireless authentication
Wireless encryption
Meaning
Specifies the authentication method used when connecting to a wireless device.
You may use any of the following types of encryption:
No encryption
Data is transmitted without encryption. With this setting, anyone within range can connect to your wireless network and might be able to access data on the network. Not recommended for anyone with private data that needs to be kept secure. [No encryption] can be selected only when [No authentication] is selected for wireless authentication.
WEP
WEP is a common encryption method supported by most devices. WEP can only be selected when wireless authentication is set to [No authentication]. Note that WEP’s encryption is weak, and networks protected with WEP are not much more secure than those with no encryption at all. Not recommended for anyone with private data that needs to be kept secure.
TKIP
TKIP is an encryption method which is more secure than WEP, but slower. Use an pre-shared key to communicate with a wireless device.
TKIP can be selected only when WPA-PSK or WPA2-PSK is selected for wireless authentication.
AES
AES is more secure than TKIP, and faster. Use a pre-shared key to communicate with a wireless device.
AES can be selected only when WPA-PSK or WPA2-PSK is selected for wireless authentication.
TKIP/AES mixed mode
TKIP/AES mixed mode allows both TKIP and AES authentication and communication. This is no more secure than TKIP alone, but more convenient for some users. TKIP/AES mixed mode can be selected only when WPA/WPA2 mixed mode - PSK is selected for wireless authentication.
- 39 -
Chapter 3 Configuration
Parameter
WPA-PSK (Pre-Shared Key)
Rekey interval
Setup WEP encryption key
Meaning
A pre-shared key or passphrase is the password for your wireless connections. There are two different formats for a pre-shared key. Use 8 to 63 alphanumeric characters (case-sensitive) for an ASCII passphrase, or use 64 alphanumeric characters (0 to 9 and a to f, not casesensitive) for a hexadecimal passphrase.
Set the update interval for the encryption key between 0 and 1440
(minutes).
A WEP encryption key (passphrase) may have any of four different formats. An ASCII passphrase may use either 5 or 13 alphanumeric characters (case-sensitive). A hexadecimal passphrase may use either 10 or 26 alphanumeric characters (0 to 9 and a to f, not case-sensitive).
- 40 -
Chapter 3 Configuration
Advanced
Configure advanced wireless settings.
Parameter
BSS Basic Rate Set
Multicast Rate
802.11n Protection
DTIM Period
Privacy Separator
Output Power
Meaning
BSS (Basic Service Set) configures the transmission rate of control communication frames for a wireless client. Setup choices may vary with different wireless clients.
Set the communication speed of multi-cast packets.
Enable to use 802.11n protection. 802.11n protection gives priority to 802.11n devices in mixed mode (11b/g or 11a) networks.
Set the beacon responding interval (1 -255) for which the AirStation responds to a wireless device. This setting is effective only when power management is enabled for the wireless device.
If enabled, the Privacy Separator blocks communication between wireless devices connected to the AirStation. Wireless devices will be able to connect to the Internet but not with each other. Devices that are connected to the AirStation with wired connections will still be able to connect to wireless devices normally.
This sets the output of the wireless signal. Because the wireless transmission output and signal distance range are nearly proportional, when the wireless transmission output is reduced, the signal distance range also becomes shorter.
- 41 -
Chapter 3 Configuration
WMM
Set priorities for specific communications.
- 42 -
Chapter 3 Configuration
Parameter
WMM-EDCA Parameters
Meaning
You don't usually need to change these settings. Using the default settings is recommended.
Priority
The following priorities may be applied to individual transmission packets: (Highest) 8, (High) 4, (Normal) 2, and
(Low) 1. From the queue, these packets are processed in order of priority.
CWmin, CWmax
The maximum and minimum value of the contention window.
The contention window is used in the frame collision avoidance structure performed in IEEE802.11, and generally, the smaller the value in the window, the higher the probability that the queue obtains the right to send.
AIFSN
The interval to send frames. The unit of the AIFSN is a slot, just as the window defined by CWmin and CWmax is. The smaller the interval of sending frames, the faster the algorithm can restart.
As a result, the priority of the queue is higher.
TXOP Limit
The period of time that the queue can use after obtaining the right to send. The unit is 32 ms. The longer this time, the more frames can be sent per right to send. However, the queue may interfere with other packet transmissions. If TXOP Limit is set to 0
(zero), only one frame can be sent per right to send.
Admission Control
Restricts new frames from interfering with a previous queue. New packets are prioritized lower until a queue of them is collected. As the new queue accumulates more packets, its priority increases.
- 43 -
Chapter 3 Configuration
MAC Filter
Restrict access to specific wireless devices.
Parameter
Enforce MAC Filtering
Registration List
Edit Registration List
MAC Addresses to be Registered
List of all clients associated with this
AirStation
Meaning
Enable to restrict wireless connections to devices with registered
MAC addresses.
Displays the MAC addresses of registered devices which are permitted to connect wirelessly.
Adds a wireless device to the list of permitted devices.
Enter a MAC address of a wireless device to permit to connect to the AirStation. Click [Register] to add that MAC address to the list.
Display the list of all MAC addresses of wireless devices connected to the AirStation.
- 44 -
Chapter 3 Configuration
Multicast Control
Configure restrictions on unnecessary multicast packets sent to the wireless LAN port.
Parameter
Snooping
Multicast Aging Time
Meaning
If enabled, snooping supervises multicast administrative packets such as IGMP and restricts unnecessary multicast transfers to wired or wireless ports.
Set the time to hold the data from multicast snooping in the range of 1 to 3600 (seconds). Enter a value bigger than the IGMP/MLD query interval.
- 45 -
Chapter 3 Configuration
AOSS
AOSS Status and Settings.
Parameter Meaning
Encryption type
Initiates AOSS automatic wireless configuration. Click this, then press or click the AOSS button on your AOSS-compatible wireless client. Repeat for additional AOSS clients.
Click this button to disconnect AOSS connections.
Note: If AOSS connections are disconnected, the SSID and encryption keys will be restored to their last settings from before AOSS was used.
Display AOSS’s Security Level status.
AOSS Button on the AirStation Unit Uncheck to disable the physical AOSS button on the AirStation.
Current Encryption Information
(AOSS connection only)
Displays the encryption type, SSID, and encryption key configured by AOSS.
[Random]
[KEY base]
Click to enter random values for SSID, encryption key, and other settings.
Click to return the SSID, encryption key, and other wireless settings to the values on the case sticker.
[Reset] Click to return the SSID, encryption key, and other wireless settings to their previous values.
- 46 -
Chapter 3 Configuration
Parameter Meaning
AOSS Client Information Displays AOSS clients connected to the AirStation and information of the devices which are wirelessly communicated.
AOSS Ethernet Converter Information
Only displayed if there are AOSS
Connections
Displays information about Ethernet converters connected to the
AirStation via AOSS.
Security (Router Mode only)
Firewall (Router Mode only)
Configure the AirStation’s firewall.
- 47 -
Chapter 3 Configuration
Parameter
Log Output
Basic Rules
Meaning
Enable to output a log of firewall activity.
Enable to use any of the quick filters. Preconfigured quick filters include:
Prohibit NBT and Microsoft-DS Routing
Enabling this blocks communication using these protocols from the WAN side to the LAN side or from the LAN side to the Internet.
You can configure this with PPPoE if you select [Use PPPoE Client]
or [Use IP Unnumbered] in Method of Acquiring IP address (page
24), or if Easy Setup identified a PPPoE connection during setup.
Reject IDENT Requests
Enabling this option will answer IDENT requests from the Internet side with corresponding rejection packets. Enable this option if you experienced slow transfer speeds for network applications such as mail, ftp or web browsing. If you have configured transfer of IDENT requests to the LAN side computer in the address translation settings (DMZ or TCP port 113), then that setting has higher priority, and overrides this setting.
Block Ping from Internet
If this is enabled, the AirStation will not respond to pings from the
Internet side. You can configure this with PPPoE if you select [Use
PPPoE Client] or [Use IP Unnumbered] in Method of Acquiring IP
address (page 24), or if Easy Setup identified a PPPoE connection
during setup.
- 48 -
Chapter 3 Configuration
IP Filter (Router Mode only)
Edit IP filters.
Parameter
Log Output
Operation
Direction
IP Address
Protocol
IP Filter Information
Meaning
If enabled, IP filter activity is saved to a log.
Specify how to process target packets.
Specify the transmission direction of target packets.
Specify the sender's IP address and receiver's IP address of the target packets.
Select a protocol for target transmission packet.
Display the list of IP filters which have been registered.
- 49 -
Chapter 3 Configuration
VPN Passthrough (Router Mode only)
Configure IPv6 passthrough, PPPoE passthrough, and PPTP passthrough.
Parameter
IPv6 Passthrough
PPPoE Passthrough
PPTP Passthrough
Meaning
Enable to use IPv6 Passthrough for address translation.
Enable to use PPPoE bridging. PPPoE bridging lets you automatically obtain an IP address from your provider for your LANside computer using the PPPoE protocol because PPPoE packets can pass between the Internet and LAN.
Enable to use PPTP passthrough for address translation.
- 50 -
Chapter 3 Configuration
LAN Config
Port Forwarding (Router Mode only)
Configure port translation.
Parameter
Group
Internet Side IP Address
Protocol
Meaning
Specify a group name for a new rule to belong to. Select [New
Group] and enter the new group name in the Group Name field to create a new group. A group name can include up to 16 alphanumeric characters.
Enter the Internet side IP address (before translation) for the port translation table entry.
Select the Internet side protocol (before translation) for the port translation table entry.
- 51 -
Chapter 3 Configuration
Parameter
LAN Side IP Address
LAN Side Port
Port Forwarding Registration
Information
Meaning
Enter the LAN side IP address (after translation) for the port translation table entry.
Select the LAN side (after translation) port number (1 - 65535) for the port translation table entry.
Shows current entries in the port translation table.
DMZ (Router Mode only)
Configure a destination to transfer communication packets without a LAN side destination to.
Parameter
IP Address of DMZ
Meaning
Enter the IP address of the destination to which packets which are not routed by a port translation table are forwarded.
Note: RIP protocol packets (UDP port number 520) will not be forwarded.
- 52 -
Chapter 3 Configuration
UPnP (Router Mode only)
Configure UPnP (Universal Plug and Play).
Parameter
UPnP
Meaning
Enable or disable Universal Plug and Play (UPnP) functionality.
- 53 -
Chapter 3 Configuration
QoS (Router Mode only)
Configure the priority of packets sent to the Internet.
Parameter Meaning
QoS for transmission to the Internet Determine whether or not to prioritize packets sent to the Internet.
Check this box to enable QoS.
Upload bandwidth Specify the upstream bandwidth in kbps from the AirStation to the internet side. Set the actual value for the upstream bandwidth.
Enable application name protocol destination Port
Enable or disable this entry.
Enter an application name. Names may use up to 32 alphanumerical characters, double or single tick marks ("'), quotation marks (“), and semicolons (;).
Select either TCP or UDP.
Specify a destination port from 1 - 65535. If this field is empty, a random port is selected.
- 54 -
Chapter 3 Configuration
Parameter priority
Meaning
Select high, medium or low. If packets do not qualify for classification as a type on the list, then their priority is treated as a level between medium and low.
NAS
Disk management
View the status of and configure attached USB disks.
- 55 -
Chapter 3 Configuration
Parameter Meaning
Device
Disk Assignment
Displays information for attached USB disks. Disks are removed when [Remove] in the Device column is clicked.
A disk number will be automatically assigned to the disk or you can choose a number. Select a disk number, or select [Do not assign], then click [Apply].
Partition Information Displays the partition information for the selected USB disk. Click
[Format] to format the disk. Note: formatting a disk will erase all information on it.
Click this to re-scan for connected USB disks. Re-recognize USB devices
Automatic USB Disk Assignment Check [Enable] to automatically select an attached USB hard disk.
The entire drive will be used as the shared folder. To configure your disk and share manually, uncheck [Enable].
FAT format file name character code Select the character code for filenames in FAT formatted partitions.
HDD power-saving function
HDD stop time
Click [Enable] to enable power saving mode.
Powers down the drive after this duration of time.
- 56 -
Chapter 3 Configuration
Shared Folder
Configure a USB disk for use with shared folders.
Parameter
Shared Folder Name*
Shared Folder Description*
Disk Partition Area*
Disclosed to*
Access Limits
Meaning
Enter a name for the shared folder. Up to 18 alphanumeric characters, spaces, hyphens (-), and underscores (_) may be used.
Enter a description of the shared folder (optional). Up to 75 alphanumeric characters, spaces, hyphens (-), and underscores (_) may be used.
Displays the partition area, format type, and the capacity of the USB disk.
Check the functionality that you want to support. Win/Mac OS
(Samba NAS), Web Access, Media Server, and/or BitTorrent may be checked. Only one folder may be chosen for either Media Server or
BitTorrent functionality.
If access limits are enabled, use the arrows to move highlighted users between the columns for [Read/Write], [Read-only], or [No access] privileges.
- 57 -
Chapter 3 Configuration
Parameter Meaning
Web Access You may also select to enforce access limits on users accessing through Web Access by checking the Access Limits checkbox.
Users will have the same access levels as assigned above. If Access
Limits is not checked, then all users accessing the shared folder via
Web Access will have [Read only] access..
Shared Folder Registration
Information*
Displays information about the shared folder.
* This is not displayed when Automatic USB Disk Assignment (page 56) is used:
The following shared folder settings are used when Disk Management is activated:
• All folders: Access limits in effect.
• Shared Folder/ Web Access: All folders are shared.
• Media Server/BitTorrent: The first folder is shared.
- 58 -
Chapter 3 Configuration
User Management
This screen lets you add users to the access list with the ability to access shared folders.
Parameter
Username
Password
User Description
Current Users
Meaning
Enter the name of a user to be given access to the shared folder. Up to 20 alphanumeric characters, space, hyphens (-), and underscores
(_) may be used for each user. Up to 16 users may be entered.
Enter the user’s password. Use of the same password that they use to log into their computer is recommended. Up to 20 alphanumeric characters, spaces, hyphens (-), and underscores
(_) may be used. For Windows 98SE/98/95 users, up to 14 alphanumeric characters may be used. Mac OS users may use up to 8 alphanumeric characters. If you enter a longer password than your users can use, then they will not be able to access the share.
Describe the user (optional). Up to 75 alphanumeric characters, spaces, hyphens (-), and underscores (_) may be used.
Lists current users, including “guest”. Guest is a built-in account that cannot be changed or deleted.
- 59 -
Chapter 3 Configuration
Shared Service
Assign AirStation and workgroup names to access shared folders.
Parameter
Shared Folder
AirStation name
AirStation Description
Workgroup name
Windows Client Language
Shared Service
Meaning
Enable to make a USB disk available on your local network.
Rename your AirStation if desired. Up to 15 alphanumeric characters, space, and hyphens (-), may be used. The AirStation name is also used as the hostname that will be used with the shared service. The shared service may not be available if you use over 15 alphanumeric characters in your AirStation’s name.
Describe the AirStation (optional). Up to 48 alphanumeric characters, space, hyphens (-), and underscores (_) may be used.
Enter your workgroup name. Up to 15 alphanumeric characters, space, hyphens (-), underscores (_), and periods (.) may be used.
Select the language to be used by the Windows client.
Displays the status of the USB disk that is used with the shared service.
- 60 -
Chapter 3 Configuration
Web Access
The screen to configure Web Access.
Parameter
Web Access
Web Access Display Language
HTTPS/SSL Encryption
Web Access External Port
Meaning
Check [Enable] to use Web Access.
Set the language to be used with Web Access.
Check [Enable] to use SSL encryption for protected data transfer.
Automatically sets the external port used for Web access. To select the port manually, select [Manual].
- 61 -
Chapter 3 Configuration
Parameter
DNS Service Hostname
Web Access
External Port Status
BuffaloNAS.com
Meaning
Sets the DNS Service Hostname when the Web access function is activated. Select [Use BuffaloNAS.com registration function] to use the Web access function easily. You’ll have to configure a [BuffaloNAS.com name] and [BuffaloNAS.com key] to use
BuffaloNAS.com. 3 - 0 alphanumeric characters, spaces, hyphens
(-), underscores (_) and period (.), may be used in the BuffaloNAS.
com name. 3 - 20 alphanumeric characters, spaces, hyphens (-), underscores (_) and period (.), may be used in the BuffaloNAS.com key.
Note: The registered name is deleted from the server if the AirStation is disconnected from power, even for a moment.
Displays the status of web access.
Displays the status of the external port.
Displays the status of BuffaloNAS.com.
- 62 -
Chapter 3 Configuration
Media Server
Media Server settings.
Parameter
Media Server
Status
Meaning
Enable to use the media server.
Displays the status of the media server.
- 63 -
Chapter 3 Configuration
BitTorrent
Configure the BitTorrent client.
Parameter
BitTorrent Function
External Port Number
Meaning
Enable to use the BitTorrent client. If the BitTorrent client is enabled, overall communication performance may decrease and settings screens may respond slower. If that happens, reformat the
USB disk with XFS. That may help performance.
Select an external port number.
- 64 -
Chapter 3 Configuration
Parameter
Bandwidth Restriction
[Download Manager]
[Delete BitTorrent information]
BitTorrent Status
BitTorrent External Port Status
Meaning
Set a bandwidth limit for BitTorrent.
Displays the BitTorrent download manager screen. Add a torrent, then click [Add] to download the file(s).
Deletes all files, including the torrent files and files which are currently downloading. Downloaded files are not deleted.
Displays the status of the BitTorrent client.
Display the external port status of the BitTorrent client.
You can download the latest Windows BitTorrent client from www.bittorrent.com.
- 65 -
Chapter 3 Configuration
Admin Config
Name
Configure basic AirStation settings.
Parameter
AirStation Name
List Network Services
Meaning
Enter a name for the AirStation. Names may include up to 64 alphanumeric characters and hyphens (-).
Enable or disable this to display the computers and devices on your network with their supported services.
- 66 -
Chapter 3 Configuration
Password
Configure the password to log in to the AirStation’s configuration screen.
Parameter
Administrator Name
Administrator Password
Meaning
The name of the Administrator account is “admin”.
The Administrator password may contain up to 8 alphanumeric characters and underscores (_).
- 67 -
Chapter 3 Configuration
Time/Date
Configure the AirStation’s internal clock.
Parameter
Local Date
Local Time
Time Zone
DST (Daylight Saving Time)
Meaning
You may manually set the date of the AirStation’s internal clock.
You may manually set the time of the AirStation’s internal clock.
Specify the time zone (offset of Greenwich Mean Time) of the
AirStation's internal clock.
You may configure the AirStation to automatically use DST
(Daylight Saving Time). If selected, the AirStation will automatically adjust the time at the beginning and end of DST.
- 68 -
Chapter 3 Configuration
NTP
Configure an NTP server to automatically synchronize the AirStation’s internal clock.
Parameter
NTP Functionality
NTP Server
Update Interval
Meaning
Enable to use an NTP server. The default is Enabled.
Enter the name of the NTP server as a hostname, hostname with domain name, or IP address. Up to 255 alphanumeric characters, hyphens (-), and underscores (_) may be used. The default is “time.
nist.gov”.
How often will the AirStation check the NTP server for the correct time? Intervals of 1 - 24 hours may be set. The default is 24 hours.
- 69 -
Chapter 3 Configuration
ECO
Configure Eco mode from this screen.
- 70 -
Chapter 3 Configuration
Parameter
Schedule feature
Weekly schedule
Register schedule
User Defined Mode
Meaning
Enable to schedule Eco Mode. If Eco mode is enabled, AOSS will function only when the AirStation is in Normal operating mode.
Graphically displays the configured schedule.
Configure operational mode for time periods in the weekly schedule. If User Defined mode is chosen, configure it below.
Individual power saving elements may be configured for User
Defined mode.
Network-USB
Configure Network-USB from this screen.
Parameter
Network-USB
Use multifunction Printer
Meaning
Network-USB allows sharing USB devices connected to the
AirStation from multiple computers on a wired or wireless LAN.
Disable to reduce the impact on the NAS and other functions, improve performance, or for security reasons.
This uses a multifunction printer supporting mass storage classes as a printer. Disable if using as a NAS instead.
- 71 -
Chapter 3 Configuration
Access
Restrict access to the AirStation’s configuration interface.
Parameter
Log Output
Prohibit configuration from wireless
LAN
Prohibit configuration from wired
LAN
Permit configuration from wired
Internet
Permitted IP address
Permitted Port
Meaning
Enabling outputs a log of changes to access settings.
If enabled, prevents access to configuration interface from wirelessly connected devices (only wired devices may configure).
If enabled, prevents access to configuration interface from wired devices (only wirelessly connected devices may configure).
If enabled, allows access to configuration interface from network devices on the WAN (Internet) side.
Displayed only if Internet side configuration is enabled. Enter the
IP address of a device that is permitted to configure the AirStation remotely from the WAN (Internet) side.
Displayed only if Internet side configuration is enabled. Set a port number (1 - 65535) to configure the AirStation from the WAN
(Internet) side.
- 72 -
Chapter 3 Configuration
Log
Transfer the AirStation’s logs to a syslog server.
Parameter
Log Transfer
Syslog Server
Logs
Meaning
Enable to send logs to a syslog server.
Identify the syslog server by hostname, hostname with domain name, or IP address. You may enter up to 255 alphanumeric characters, hyphens (-), and underscores (_).
Choose which logs will be transferred to the syslog server.
- 73 -
Chapter 3 Configuration
Save/Restore
Save AirStation settings as a file and restore from them later.
Parameter
Save current settings
Restore Configuration from Backup
File
Meaning
Clicking [Save] will save the current configuration of the AirStation to a file. If the [Encrypt the configuration file with a password] option is checked, then the configuration file will be password protected with the current administrator password.
Restore the configuration of the AirStation from a saved configuration file by clicking the [Browse...] button, navigating to the configuration file, and then clicking [Restore]. If the configuration file was password protected, then put a check next to [To restore from the file you need the password], enter the password, and click [Open].
- 74 -
Chapter 3 Configuration
Initialize/Restart
Initialize or restart the AirStation.
Parameter
Restart
Initialize
Meaning
Click [Restart Now] to restart the AirStation.
Click [Initialize Now] to initialize and restart the AirStation.
- 75 -
Chapter 3 Configuration
Update
Update the AirStation’s firmware.
Parameter
Firmware Version
Update Method
Firmware File Name
Meaning
Displays the current firmware version of the AirStation.
Specify Local File
Updates from a firmware file stored on your computer.
Automatic Update Online
Automatically updates to the latest firmware available.
Click [Browse...] to navigate to the firmware file on your computer if [Specify Local File] was selected. You don’t need to specify the firmware location if you’re using [Automatic Update]. Click [Update
Firmware] to update the firmware.
- 76 -
Chapter 3 Configuration
Parameter
Firmware Update Reminder
Remind time
Meaning
This sets whether the Firmware Update Reminder function is used.
When enabled, if new firmware is found, notification is sent to the
Configuration Interface.
This sets the interval for checking whether a new firmware version has been released.
- 77 -
Chapter 3 Configuration
Diagnostic
System Info
View system information for the AirStation.
- 78 -
Chapter 3 Configuration
Parameter
Model
AirStation Name
Mode Switch Status
Operational Mode
Internet
LAN
Wireless
NAS
ECO Mode
Meaning
Displays the product name of the AirStation and the firmware version.
Displays the name of the AirStation.
Displays the status of the AirStation’s mode switch.
Displays the AirStation’s current operational mode.
Displays information about the Internet port.
Displays information about the LAN port.
Displays the wireless status.
Displays information about the USB disk.
This indicates the operating status of ECO Mode.
- 79 -
Chapter 3 Configuration
Logs
The AirStation’s logs are recorded here.
Parameter
Display log info
Logs
Meaning
Choose the types of logs to display.
Displays the log information recorded in the AirStation.
- 80 -
Chapter 3 Configuration
Packet Info
View packet transfer information.
Parameter
Sent
Received
Meaning
Displays the number of packets sent to the WAN, the LAN, and the wireless LAN.
Displays the number of packets received from the WAN, the LAN, and the wireless LAN.
- 81 -
Chapter 3 Configuration
Client Monitor
This screen shows devices that are connected to the AirStation.
Parameter
Client Monitor
Meaning
Displays information (MAC address, lease IP address, hostname, communication method, wireless authentication and 802.11n) for devices that are connected to the AirStation.
- 82 -
Chapter 3 Configuration
Ping
A ping test checks whether the AirStation can communicate with a specific network device.
Parameter
Destination Address
Meaning
Enter the IP address or hostname of the device that you are testing communication with, then click [Execute]. The result will be displayed below.
- 83 -
Chapter 4 - Connect to a Wireless Network
Automatic Secure Setup (AOSS / WPS)
AOSS and WPS are systems that enable you to automatically configure wireless LAN settings. Just pressing the buttons will connect wireless devices and complete security settings. Use them to automatically connect wireless devices, computers, or game machines which support AOSS or WPS.
AOSS (AirStation One-Touch Secure System) is technology developed by Buffalo
Technology. WPS was created by the Wi-Fi Alliance.
Internet
PUSH
PUSH
Modem AirStation PC or
Game console
(AOSS Devices)
• Before using AOSS or WPS to connect the Buffalo wireless client to the computer, download Client
Manager or AOSS Assistant from the Buffalo website and install it.
• Buffalo’s Client Manager software can be used with the wireless LAN devices built into your computer. However, it is not guaranteed to work with all wireless LAN devices available.
- 84 -
Chapter 4 Connect to a Wireless Network
Windows 7/Vista (Client Manager V)
If you are using Windows 7 or Vista, use the Client Manager V to connect wirelessly with AOSS or
WPS.
1
2
Click [Start] > [All Programs] > [BUFFALO] > [AirStation Utility] > [Client Manager V].
Click [Create Profi le].
3
If the User Account Control screen opens, click [Yes] or [Continue].
4 Click the [WPS AOSS ] button.
Follow any instructions displayed on the screen. When the Wireless LED on the front of the
AirStation stop fl ashing and glows steadily, the connection is complete.
- 85 -
Chapter 4 Connect to a Wireless Network
Windows XP (Client Manager 3)
If you are using Windows XP, use Client Manager 3 to connect wirelessly with AOSS or WPS.
1
2
Right-click on the icon in the system tray and select [Profi le].
Click the [WPS AOSS] button.
It will take several seconds for your wireless connection to be confi gured. When the Wireless LED on the front of the AirStation stop fl ashing and glows steadily, the connection is complete.
- 86 -
Chapter 4 Connect to a Wireless Network
Mac OS X (AOSS Assistant)
If you are using Mac OS X 10.7 / 10.6 / 10.5 / 10.4, use the AOSS Assistant to connect wirelessly with
AOSS.
1
Run the AOSS Assistant program that was downloaded from the Buffalo web site.
2
The software license screen is displayed. Click [Agree] to proceed.
3
4
Click [Start AOSS ].
Enter the Mac’s username and password and click [OK].
It will take several seconds for your wireless connection to be configured. When the Wireless LED on the front of the AirStation stop flashing and glows steadily, the connection is complete.
- 87 -
Chapter 4 Connect to a Wireless Network
Other Devices (e.g. Game Console)
If you are using a game machine which supports AOSS or WPS, refer to that device’s manual to initiate AOSS or WPS. When instructed, hold down the AOSS button on the AirStation for 1 second.
When the Wireless LED on the front of the AirStation stop flashing and glows steadily, the connection is complete.
Manual Setup
You can also connect to the AirStation without installing Client Manager V or Client Manager 3 by using the utility built-in to operating system. The procedure varies depending on which version of operating system you are using.
Windows 7 (WLAN AutoConfig)
With Windows 7, use WLAN AutoConfig to connect to the AirStation.
1
Click on the network icon in the system tray .
2 Select the target AirStation and click
[Connect]. If you will be connecting to this device in the future, checking [Connect automatically] is recommended.
- 88 -
Chapter 4 Connect to a Wireless Network
3 Enter the encryption key and click [OK].
Windows Vista (WLAN AutoConfig)
With Vista, use WLAN AutoConfig to connect to the AirStation.
1
Right-click on the wireless network icon in the system tray.
2 Click [Connect to a network ] .
3 When this screen is displayed, select your network and click [Connect ] .
- 89 -
Chapter 4 Connect to a Wireless Network
If the screen below is displayed, click [I want to enter the network key or passphrase instead].
Otherwise,go to step 4.
- 90 -
Chapter 4 Connect to a Wireless Network
4 Enter the encryption key and click [Connect].
Step through the wizard to finish configuration.
If the Set Network Location screen is displayed, select [Home], [Work], or [Public location] depending on where you’re using the AirStation.
- 91 -
Chapter 4 Connect to a Wireless Network
Windows XP (Wireless Zero Configuration)
Windows XP includes Wireless Zero Config, a built-in utility to connect to your AirStation.
Note: If Client Manager 3 is installed on your computer, Wireless Zero Config is disabled. Uninstall Client
Manager 3 to use Wireless Zero Config, or just use Client Manager 3 to connect to the AirStation.
1
Right-click on the wireless network icon in the system tray.
2
Click [View Available Wireless Networks].
3 Select the network to connect to and click
[Connect].
4 Enter the encryption key (twice) and click
[Connect].
It will take several seconds for configuration to complete.
- 92 -
Chapter 4 Connect to a Wireless Network
Mac OS X (Wi-Fi)
Use Wi-Fi on a Mac to connect to the AirStation.
Note: In Mac OS X 10.6 and earlier, “Wi-Fi” appears as “AirPort”.
1
2
Refer to the setup card at the bottom of the
AirStation. Make a note of the SSID and Key printed on the setup card.
Click the icon in the top section of the screen and select
[Turn Wi-Fi On].
3
Find the SSID from step 1 on the list.
Click it to highlight it.
4
Enter the Key from step 1 into the Password entry box, check
[Remember this network], and click
[OK].
It will take several seconds for configuration to complete.
- 93 -
Chapter 5 - Troubleshooting
Cannot connect to the Internet over wired connection.
• Make sure that your AirStation is plugged in!
• Check that the status LEDs of your AirStation are lit as below:
Internet access Blue light is on
Buffalo White light is on
LAN
Internet
Green light is on or blinking
Green light is on or blinking
• Make sure that your computer is configured to “obtain an IP address automatically from DHCP”.
• Restart your AirStation.
Cannot access the web-based configuration Interface.
• See chapter 3 for instructions to open the AirStation’s configuration interface.
• Enter the correct username and password to log in to the configuration interface. If you are using
AirStation with factory default settings, enter “admin” for the username and “password” for the password.
• Verify that your web browser is not set to use proxies.
• Make sure that your computer is configured to “obtain an IP address automatically from DHCP”.
• Restart your AirStation.
- 94 -
Chapter 5 Trouble Shooting
Cannot connect to the network wirelessly.
• Configure your wireless client with the same SSID, encryption type, and encryption key as set on the AirStation.
The factory defaults are:
SSID - BUFFALO-XXXXXX (the last 6 digits of the AirStation’s MAC address)
Encryption Type - WPA/WPA2 mixed mode - PSK, or none.
Encryption Key - Printed on the Setup card.
Note: For details, refer to the Setup card.
• Place your AirStation and wireless devices 2 - 10 feet apart.
• Restart your AirStation.
You forgot AirStation's SSID, Encryption Key, or
Password.
Hold down the reset button on the base of your AirStation for 3 seconds to initialize its settings. All settings, including your password, SSID, and encryption key will be initialized to their defaults.
Restoring the Default Configuration
With the AirStation powered on, hold down this button for 3 seconds to return it to factory default settings.
- 95 -
Chapter 5 Trouble Shooting
TCP/IP Settings (Windows 7)
To configure TCP/IP in Windows 7, follow the procedure below.
1
Click [Start] > [Control Panel] > [Network and Internet].
2
Click [Network and Sharing Center].
3
Click [Change Adapter Settings] on the left side menu.
4
Right-click on [Local Area Connection], then click [Properties].
5
If the User Account Control screen opens, click [Yes] or [Continue].
6
Select [Internet Protocol Version 4 (TCP/IPv4)] then click [Properties].
7
To have DHCP set your IP address settings automatically, check [Obtain an IP address automatically] and [Obtain DNS server address automatically].
To set your IP address settings manually, enter values for each setting. Examples:
If the router’s IP address is 192.168.11.1,
IP address 192.168.11.80
Subnet mask 255.255.255.0
Default gateway
Preferred DNS server
Alternate DNS server
192.168.11.1
192.168.11.1
blank
8
Click [OK].
- 96 -
Chapter 5 Trouble Shooting
TCP/IP Settings (Windows Vista)
To configure TCP/IP in Windows Vista, follow the procedure below.
1
Click [Start] > [Settings] > [Control Panel].
2
Click [Network and Sharing Center].
3
Click [Manage network connections] on the left side menu.
4
Right-click on [Local Area Connection], then click [Properties].
5
If the User Account Control screen opens, click [Yes] or [Continue].
6
Select [Internet Protocol Version 4 (TCP/IPv4)], then click [Properties].
7
To have DHCP set your IP address settings automatically, check [Obtain an IP address automatically] and [Obtain DNS server address automatically].
To set your IP address settings manually, enter values for each settings. Example:
If the router’s IP address is 192.168.11.1,
IP address 192.168.11.80
Subnet mask 255.255.255.0
Default gateway
Preferred DNS server
Alternate DNS server
192.168.11.1
192.168.11.1
blank
8
Click [Close].
- 97 -
Chapter 5 Trouble Shooting
TCP/IP Settings (Windows XP)
To configure TCP/IP in Windows XP, follow the procedure below.
1
Click [Start] > [Settings] > [Control Panel].
2
Double-click [Network].
3
Right-click on [Local Area Connection], then click [Properties].
4
Select [Internet Protocol (TCP/IP)], then click [Properties].
5
To have DHCP set your IP address settings automatically, check [Obtain an IP address automatically] and [Obtain DNS server address automatically].
To set your IP address settings manually, enter values for each setting. Examples:
If the router’s IP address is 192.168.11.1,
IP address
Subnet mask
Default gateway
Preferred DNS server
Alternate DNS server
192.168.11.80
255.255.255.0
192.168.11.1
192.168.11.1
blank
6
Click [Close].
- 98 -
Chapter 5 Trouble Shooting
TCP/IP Settings (Mac OS X)
To configure TCP/IP in Mac OS X, follow the procedure below.
1
Click [Apple menu] > [System Preferences…].
2
Click [Network].
3
Click [Ethernet].
4
To have DHCP set your IP address settings automatically, select [Using DHCP] in the Configure
IPv4 field.
To set your IP address settings manually, select [Manually] in the Configure IPv4 field and enter values for each setting. Examples:
If the router’s IP address is 192.168.11.1,
IP Address 192.168.11.80
Subnet Mask
Router
255.255.255.0
192.168.11.1
DNS Server
Search Domains
192.168.11.1
blank
5
Click [Apply].
- 99 -
Chapter 5 Trouble Shooting
Other Tips
Issue:
I reset my wireless router to factory settings and forgot how to log in to the configuration interface.
Answer:
Open your browser, enter 192.168.11.1 as the browser address, and hit Enter. You will be prompted to log in. Enter “admin” for the username and “password” for the password. Click [OK] to log in. The option to reset your password will be available on the first page.
Issue:
How do I forward ports on my wireless router for my gaming console?
Answer:
Log in to the router. From the home page, go to the Internet Game/ Port Mapping section. Enter the port that needs to be forwarded and the IP address of the gaming console.
Issue:
How do I enable or modify security encryption settings on the wireless router?
Answer:
Go to the Wireless Config tab and then select the Security tab. Buffalo recommends the use of WPA/
WPA2 mixed for wireless encryption. The passphrase/ key should be at least 8 characters in length.
Issue:
How do I change my wireless router’s broadcasted network name (SSID)?
Answer:
Log in to the wireless router with your browser. Navigate to Wireless Config - Basic. Find the SSID setting. Select [Use] and enter the new name for your network. Click [Apply]. Once the wireless router has rebooted, you will need reconnect any wireless clients to the AirStation using the new network name. The encryption key will still be the same.
- 100 -
Chapter 5 Trouble Shooting
Issue:
What can I do if my wireless connection drops randomly or seems slow?
Answer:
There are many environmental factors that may cause this. First, ensure the issue is not range related by moving the wireless router and the client device closer together. If the connection drops continue, then range is probably not the issue.
Other 2.4 GHz devices such as microwaves, other wireless networks, and 2.4 GHz wireless phones may impact performance. Try a different wireless channel for your wireless router. Log in to the wireless router with your browser. Click on the Wireless Config tab and then the Basic tab. Wireless channels from 1 - 11 may be selected. Try the Auto-Channel option if available. Otherwise, manually select an alternate channel and click [Apply].
Issue:
Though I am able to successfully make a connection with my wireless router, I am unable to access the Internet with my web browser.
Answer:
First, power off the cable or DSL modem, the wireless router, and your computer. Move the router's mode switch to the on position. Verify that the modem is connected to the wireless router with an
Ethernet cable to the WAN port. Power on the modem and wait one minute. Power on the wireless router and wait another minute. Power on the computer. Open a browser on the computer and navigate to a familiar website to verify whether the Internet connection is functioning normally.
If after these steps, an Internet connection is still unavailable, power off the cable or DSL modem and computer again and directly connect your computer to the cable or DSL modem with a cable between the computer and the port on the modem. Power on the modem and wait one minute.
Power on the computer and again check for an Internet connection.
If an Internet connection IS NOT available with a direct connection to the computer, please call the
Internet Service Provider who installed the modem.
If an Internet connection IS available with a direct connection to the computer, please call our customer support.
Issue:
Where can I download the latest drivers, firmware, and instructions for my Buffalo wireless products?
Answer:
The latest drivers and firmware are available online at www.buffalotech.com
- 101 -
Chapter 6 - Default Configuration Settings
Feature
Internet
(Router mode only)
PPPoE
(Router mode only)
DDNS
(Router mode only)
VPN Server
(Router mode only)
Parameter
Method of Acquiring IP Address
Default Gateway
DNS Name Server Address
Internet MAC Address
MTU Size of Internet Port
Default PPPoE Connection
IP Unnumbered PPPoE
Connection
PPPoE Connection List
Preferred Connections
Dynamic DNS Service
Current Dynamic DNS
Information
LAN Side IP Address
DHCP Server Function
DHCP IP Address Pool
PPTP Server Function
Authorization Type
Server IP Address
Client IP Address
DNS Server IP Address
WINS Server IP Address
MTU/MRU value
PPTP User List
Default Setting
Perform Easy Setup (Internet Connection Wizard) none none
Use Default MAC Address
1500 Bytes
No Active Session
No Active Session none none
Disabled none
192.168.11.1 (255.255.255.0)
Enabled
192.168.11.2 for up to 64 Address(es)
Disabled
MS-CHAPv2 (40/128-bit Encryption)
Auto
Auto
LAN IP address of the AirStation none
1396 none
- 102 -
Chapter 6 Default Configuration Settings
Feature
LAN
Parameter
LAN Side IP Address
Default Setting
Router mode (Router On):
192.168.11.1 (255.255.255.0)
Bridge mode (Router Off):
192.168.11.100 (255.255.255.0)
Enabled DHCP Server Function
(Router mode only)
DHCP IP Address Pool
(Router mode only)
LAN Side IP Address
(For IP Unnumbered)
(Router mode only)
Lease Period
(Router mode only)
Default Gateway
(Router mode only)
192.168.11.2 for up to 64 Addresses none
48 Hours
AirStation's IP Address
DNS Servers
(Router mode only)
WINS Server
(Router mode only)
AirStation's IP Address
Do Not Specify
Domain Name
(Router mode only)
Default Gateway
(Bridge mode only)
DNS Server Address
(Bridge mode only)
Assigned Domain Name none none
Current DHCP Client Information none DHCP Lease
(Router mode only)
NAT
(Router mode only)
Address Translation Enabled
Route
Log Output of Deleted Packets
Routing Information
Disabled none
- 103 -
Chapter 6 Default Configuration Settings
Feature
WPS
Basic
Advanced
Parameter
WPS
External Registrar
AirStation PIN
WPS Security Information
Wireless Radio
SSID
Wireless Channel
High-throughput mode
Broadcast SSID
Wireless authentication
Wireless encryption
WPA-PSK (Pre-Shared Key)
Rekey interval
BSS Basic Rate Set
Multicast Rate
802.11n Protection
DTIM Period
Privacy Separator
Output Power
Default Setting
Enabled
Enabled
An 8-digit random value
(Printed on the label of the AirStation)
WPS status:
SSID:
Security: configured
BUFFALO-XXXXXX (the last 6 digits of the AirStation’s MAC address)
WPA/WPA2 mixedmode - PSK
TKIP/AES mixedmode or none
Encryption key: Either a 13-digit random value or disabled. Printed on the label of the AirStation. Encryption is disabled by default settings on
AirStation for Asia Pacific.
Enabled
Use AirStation's MAC address
Auto Channel
11ac/n/a
Bandwidth: 11ac/n/a 1300 Mbps Mode (80 MHz)
Extension Channel: -
11n/g/b
Bandwidth: 11n/g/b Normal Mode (20 MHz)
Extension Channel: -
Allow
WPA/WPA2 mixedmode - PSK, or no authentication
TKIP/AES mixedmode, or no encryption
A 13-digit random value or disabled
(Printed on the setup card. Encryption is disabled in default settings on AirStation for Asia Pacific.)
60 minutes
11ac/n/a
6, 12, 24 Mbps
- 104 -
11n/g/b
1, 2, 5.5, 11 Mbps
Auto
Disabled
1
Disabled
100%
Chapter 6 Default Configuration Settings
Feature
WMM
MAC Filter
Parameter
WMM-EDCA Parameters
(Priority AC_BK (Low) )
WMM-EDCA Parameters
(Priority AC_BE (Normal) )
WMM-EDCA Parameters
(Priority AC_VI (High) )
WMM-EDCA Parameters
(Priority AC_VO (Highest) )
Enforce MAC Filtering
Registration List
Multicast control Snooping
Multicast Aging Time
AOSS Encryption Type
AOSS Button on the AirStation
Unit
Default Setting
CWmin
CWmax
AIFSN
TXOP Limit
Admission Control
CWmin
CWmax
AIFSN
TXOP Limit
Admission Control
CWmin
CWmax
AIFSN
TXOP Limit
Admission Control
CWmin
CWmax
AIFSN
TXOP Limit
Admission Control
11ac/n/a
Disabled
11n/g/b
Disabled none
Enabled
300 sec.
none
Enabled
For STA
15
1023
7
0
Disabled
For STA
15
1023
3
0
Disabled
For STA
7
15
3
7
2
2
94
Disabled
For STA
47
Disabled
For AP
15
63
3
0
-----
For AP
7
15
For AP
15
1023
7
0
-----
3
7
1
1
94
-----
For AP
47
-----
- 105 -
Chapter 6 Default Configuration Settings
Feature
Firewall
(Router mode only)
Parameter
Log Output
Basic Rules
IP Filter
(Router mode only)
VPN Pass
Through
(Router mode only)
Port Forwarding
(Router mode only)
DMZ
(Router mode only)
UPnP
(Router mode only)
QoS
(Router mode only)
Disk
Management
Log Output
IP Filter Information
IPv6 Pass Through
PPPoE Pass Through
PPTP Pass Through
Port Forwarding Registration
Information
IP Address of DMZ
UPnP
QoS for transmission to the
Internet
Automatic USB Disk Assignment
FAT format file name character code
HDD power-saving function
Shared Folder Access Limits
Web Access
Current Users User
Management
Shared Service Shared Folder
AirStation Name
AirStation Description
Workgroup Name
Windows Client Language
Shared Service
Default Setting
Disabled
Prohibit NBT and Microsoft-DS Routing Disabled
Reject IDENT Requests Enabled
Block Ping from Internet Enabled
Disabled none
Disabled
Disabled
Enabled none none
Enabled
Disabled
Enabled
North America (CP437)
Disabled
HDD stop time 10 Minutes
No Limits (Read/Write)
Access Limits guest
Enabled
AP + AirStation’s MAC Address
None
WORKGROUP
North America (CP437)
None
- 106 -
Chapter 6 Default Configuration Settings
Feature
Web Access
Media Server
BitTorrent
Parameter
Web Access
Web Access Display Language
HTTPS/SSL Encryption
Web Access External Port
DNS Service Host Name
Web Access status
Media Server
Status
BitTorrent Function
External Port Number
Bandwidth Restriction
Name
Password
Time/Date
NTP
BitTorrent Status
AirStation Name
List Network Services
Administrator Name
Administrator Password
Local Date
Local Time
Time Zone
DST (Daylight Saving Time)
NTP Functionality
NTP Server
Update Interval
Default Setting
Disabled
English
Disabled
Auto (Port Number:9000)
Use BuffaloNAS.com registration function
None
Disabled
None
Disabled
Auto (Port Number: 9002)
Enabled
Maximum Download Speed 1000 KB/s
Maximum Upload Speed 200 KB/s none
AP + AirStation's MAC Address
Enabled admin (fixed) password
2012 Year 1 Month 1 Day
0 Hour 0 Minute 0 Seconds
(GMT - 06:00) Central Standard Time: CST
USA (From Second Sunday in Mar to first Sunday in
Nov)
Enabled time.nist.gov
24 hours
- 107 -
Chapter 6 Default Configuration Settings
Feature
ECO
Update
Parameter
Schedule feature
Register schedule
User Define Mode
Network-USB
Access
Network-USB
Use multifunction Printer
Log Output
Limitation Item
Log Log Transfer
Syslog Server
Logs
Update Method
Firmware Update Reminder
Remind Time
Default Setting
Disabled
Operational Mode: Normal
Start time: 0:00
End time: 0:30
The day of week: none
LED: Off
Wired LAN: ECO (Slow operation)
Wireless LAN: Off
Enabled
Enabled
Disable
Prohibit configuration from wireless LAN Disabled
Prohibit configuration from wired LAN Disabled
Permit configuration from wired Internet Disabled
Disabled none
Router Mode:
Address Translation, IP Filter, Firewall, PPPoE
Client, Dynamic DNS, DHCP Client, DHCP Server,
AOSS, Wireless Client, Authentication, Setting
Changes, System Boot, NTP Client, Wired Link, and System
Bridge Mode:
IP Filter, DHCP Client, AOSS, Wireless Client,
Authentication, Setting Changes, System Boot,
NTP Client, Wired Link, and System
Specify Local File
Enabled
Automatic
- 108 -
Chapter 7 - Network-USB Navigator
Network-USB Navigator is compatible only with printers and multifunction printers (all-in-one devices with a printer, scanner, and memory card reader). It cannot be used with any other type of
USB devices.
Initial Setup for Windows Users
1
Insert the AirNavigator CD into your computer.
The setup menu will launch automatically. If not, open the CD and click on “Launcher.exe” in the “win” folder.
2
Click [Software installation].
- 109 -
4
5
Chapter 7 Network-USB Navigator
3
Check the box for “Network-USB
Navigator” and click [Install].
Click [Next].
- 110 -
Click [Yes].
Chapter 7 Network-USB Navigator
6
7
Click [Next].
Click [Next].
8
Click [Start].
- 111 -
Chapter 7 Network-USB Navigator
・ Installation on Windows XP (SP2 or later)
Click [Yes] when this screen is shown.
・ Installation on Windows 7/Vista
Click [Install] when this screen is shown.
Click [Yes] when this screen is shown.
- 112 -
Chapter 7 Network-USB Navigator
9
1 You can select the behavior of this product when a USB device is detected. Select the connection behavior suited to your usage environment.
2 Click [Next].
10
Click [Finish] when the “Network-USB Navigator Install is Complete” screen is shown.
Network-USB Navigator installation is complete.
- 113 -
Chapter 7 Network-USB Navigator
Initial Setup for Mac Users
1
Insert the Air Navigator CD.
2
From the menu bar, click [Go] > [Computer].
3
Double-click the CD icon, and then double-click [Mac] > [DeviceServer] > [Cosetup].
4
Click [Continue].
5
Click [Continue].
- 114 -
Chapter 7 Network-USB Navigator
6
7
Click [Agree].
Click [Continue].
8
Click [Install].
- 115 -
Chapter 7 Network-USB Navigator
9
10
11
Input your name and password.
Click [OK].
Click [Continue Installation].
Click [Restart].
- 116 -
Chapter 7 Network-USB Navigator
12 1 During the first program launch only, the screen at left will appear before the main program screen is displayed. From here, you can select the behavior of this product when a USB device is detected. Select the connection behavior suited to your usage environment.
2 Click [OK].
Network-USB Navigator installation is complete.
Opening the Network-USB User Manual
1
Launch Network-USB Navigator.
There are two ways to launch the program.
Windows Users a) Click the task tray icon .
b) From the Start menu, click [(All) Programs]-[BUFFALO]-[Network-USB Navigator]-[Network-
USB Navigator].
Macintosh Users a) Click the Dock icon .
b) Click [Macintosh HD]-[Applications]-[BUFFALO]-[Device Server]-[Network-USB Navigator].
- 117 -
Chapter 7 Network-USB Navigator
2
3
Network-USB User Manual will open.
How to use Network-USB
To configure Network-USB, refer to the “Network-USB User Manual”.
Click
Page].
, then click [Manual
- 118 -
Chapter 8 - Checking Wireless Signal Quality
For users of Windows 7, Vista, or Mac OS X (10.4 and later), software supplied with the AirStation can be used to check the quality and strength of the wireless signal.
Windows 7/Vista
Note: · If Client Manager V is not already installed, download it from the Buffalo web site, and install.
· Client Manager V does not support Windows XP.
1 Click [Start] > [All Programs] > [BUFFALO] > [AirStation Utility] > [Client Manager V].
2
Click [Advanced Setup].
3
When the Client Manager V status screen is displayed, click .
- 119 -
Chapter 8 Checking the Wireless Signal Quality and Strength
4
Parameter
Connection status
Usage status by channel
Meaning
Signal strength (dBm), link speed (Mbps), and signal quality (%) are displayed in one-minute intervals on a real-time graph.
The 11b/11g display shows usage in the 2.4 GHz band channels 1 to 11.
The 11a display shows usage in the W52, W53, and W56 channels.
Colors are used to indicate the signal strength of the access point. Colors closer to red indicate an access point with a stronger signal strength, and colors closer to blue indicate an access point with a weaker signal strength.
Mac OS X
1
Run the WLAN Monitor program that was downloaded from the Buffalo web site.
- 120 -
Chapter 8 Checking the Wireless Signal Quality and Strength
2
The software license screen is displayed when starting for the first time only. Click [Agree] to proceed.
3
Parameter
Network name (SSID)
Status
IP Address
Security
Encryption
Band
Channel
Link Speed (Mbps)
Quality (%)
Signal Level (dBm)
Meaning
This displays the SSID of the AirStation that is currently connected.
This indicates the current connection status.
This indicates the IP address of the current wireless network port
(Wi-Fi).
This indicates the authentication method for the current connection target.
This displays the encryption type for the current connection target.
This displays the wireless band for the current connection target.
This displays the wireless channel for the current connection target.
This displays the current link speed.
This displays the current signal quality.
This indicates the strength of the current signal.
- 121 -
Chapter 9 - Shared Folders and the USB Port
There are several restrictions on using the AirStation’s USB port:
• When using two-byte characters (such as Japanese), keep folder and file names within 80 characters. You may not be able to copy a folder or a file whose name length is more than 80 characters.
• You cannot set attributes (hidden or read-only) for folders or files on the AirStation.
• When using access restrictions, you can register up to 16 users for the AirStation.
• Please note that you are not allowed to use any of the following words as a user or group name: adm, administrator, all, bin, daemon, disk, ftp, guest, halt, hdusers, kmen, lp, mail, man, news, nobody, nogroup, none, operator, root, shadow, shutdown, sshd, sync, sys, ttyusers, utmp, uucp, www.
• Please note that you are not allowed to use any of the following words as a shared folder name: global, homes, printers, bittorrent, disk1_pt1, disk1_pt2, disk1_pt3, disk1_pt4, disk2_pt1, disk2_ pt2, disk2_pt3, disk2_pt4, disk3_pt1, disk3_pt2, disk3_pt3, disk3_pt4, disk4_pt1, disk4_pt2, disk4_ pt3, disk4_pt4.
• If shared folder names, work group names, or file names contain any of the following characters, you may not access data or manipulate files on the AirStation properly. In such a case, use a different character.
• If a file created on a Macintosh contains any of the following characters, it will not be displayed correctly under Windows OS. Also, you cannot copy or properly display a file when connecting via
SMB from Mac OS X if it contains any of these characters:
? [ ] / \ = + < > ; : ” , | *
• Cancelling or aborting a file copy may leave the file incomplete, and you may no longer be able to delete the incomplete file. This can also happen during a power outage or if the LAN cable is suddenly disconnected. If it happens, restart the AirStation, delete the file, and try copying the file again.
• Use the same username and password for the AirStation as the user’s Windows login. If they are different, the user may not be able to access shared folders with access restrictions on the
AirStation.
• Date and time stamps stored on the USB hard drive may be updated by the OS accessing the
AirStation. File creation or access dates may not be maintained.
- 122 -
Chapter 9 Technical Detail of the USB port
• If you view the size of a hard drives on the browser, it shows a bigger value than when you see it in
Windows’ drive properties. This is because the browser shows the size of the drive in gigabytes but
Windows shows it in gibibytes.
• If you have logged in using a “guest” account from Windows 7, Vista, XP or 2000, access restrictions may not work properly. A (different) guest account already exists on the AirStation.
• If you access a shared folder from a Macintosh computer, additional Mac OS X information files may be automatically generated. Do not delete these files from a Windows computer. Otherwise, you may no longer be able to access folders from a Macintosh.
• Device types that can be connected to the AirStation’s USB connector are USB hard drives, USB memory sticks, or USB card readers. Card readers with 5 or more slots are not supported. USB devices such as a digital cameras, CD/DVD drives, USB hubs, mice, or keyboards are not supported.
• Encrypted USB hard drives are not supported.
• Only one single drive may be connected to the AirStation’s USB port at a time. Drives manufactured by other companies besides Buffalo Technology are not supported.
• If your hard drive has an auto power mode switch, move the switch to [manual] or [on]. Leaving the switch set to [auto] may result in unpredictable behavior.
• Up to 4 partitions can be recognized on a USB hard drive.
• Available file systems for USB hard drives are FAT12, FAT16, FAT32, and XFS.
- 123 -
Appendix A - Specifications
Wired LAN Interface
Standard Compliance
Transmission Rate
Transmission Encoding
IEEE802.3ab (1000BASE-T), IEEE802.3u (100BASE-TX), IEEE802.3 (10BASE-T)
10 / 100 / 1000 Mbps
1000BASE-T 4DPAM5, 100BASE-TX 4B5B/MLT-3, 10BASE-T Manchester Cording
Access Method CSMA/CD
Speed and Flow Control 10 / 100 / 1000 Mbps, Auto Sensing, Auto MDIX
Number of LAN Ports
LAN Port Connector
Wireless LAN Interface
4
RJ-45
Standard Compliance
Transmission Method
Frequency Range
Transmission Rate
802.11ac (Draft)
IEEE802.11ac (Draft 2.0) /n/a/g/b
Direct Sequence Spread Spectrum (DSSS), OFDM, MIMO
Available frequencies depend on the country of purchase. See the next page for details.
802.11ac (Draft):
20 MHz BW (Long GI)
260, 234, 195, 175.5, 156, 117, 78, 58.5, 39, 19.5 Mbps (3 stream)
156, 130, 117, 104, 78, 52, 39, 26, 13 Mbps (2 stream)
78, 65, 58.5, 52, 39, 26, 19.5, 13, 6.5 Mbps (1 stream)
20 MHz BW (Short GI)
288.9, 260, 216.7, 195, 173.3, 130, 86.7, 65, 43.3, 21.7 Mbps (3 stream)
173.3, 144.4, 130, 115.6, 86.7, 57.8, 43.3, 28.9, 14.4 Mbps (2 stream)
86.7, 72.2, 65, 57.8, 43.3, 28.9, 21.7, 14.4, 7.2 Mbps (1 stream)
40 MHz BW (Long GI)
540, 486, 405, 364.5, 324, 243, 162, 121.5, 81, 40.5 Mbps (3 stream)
360, 324, 270, 243, 216, 162, 108, 81, 54, 27 Mbps (2 stream)
180, 162, 135, 121.5, 108, 81, 54, 40.5, 27, 13.5 Mbps (1 stream)
40 MHz BW (Short GI)
600, 540, 450, 405, 360, 270, 180, 135, 90, 45 Mbps (3 stream)
400, 360, 300, 270, 240, 180, 120, 90, 60, 30 Mbps (2 stream)
200, 180, 150, 135, 120, 90, 60, 45, 30, 15 Mbps (1 stream)
80 MHz BW (Long GI)
1170, 1053, 877.5, 702, 526.5, 351, 263.3, 175.5, 87.8 Mbps (3 stream)
780, 702, 585, 526.5, 468, 351, 234, 175.5, 117, 58.5 Mbps (2 stream)
390, 351, 292.5, 263.3, 234, 175.5, 117, 87.8, 58.5, 29.3 Mbps (1 stream)
80 MHz BW (Short GI)
1300, 1170, 975, 780, 585, 390, 292.5, 195, 97.5 Mbps (3 stream)
866.7, 780, 650, 585, 520, 390, 260, 195, 130, 65 Mbps (2 stream)
433.3, 390, 325, 292.5, 260, 195, 130, 97.5, 65, 32.5 Mbps (1 stream)
- I -
Appendix A Specifications
Transmission Rate
802.11n/a/b/g
Access Mode
Security
802.11n:
20 MHz BW (Long GI)
195, 175.5, 156, 117, 78, 58.5, 39, 19.5 Mbps (3 stream)
130, 117, 104, 78, 52, 39, 26, 13 Mbps (2 stream)
65, 58.5, 52, 39, 26, 19.5, 13, 6.5 Mbps (1 stream)
20 MHz BW (Short GI)
216.7, 195, 173.3, 130, 86.7, 65, 43.3, 21.7 Mbps (3 stream)
144.4, 130, 115.6, 86.7, 57.8, 43.3, 28.9, 14.4 Mbps (2 stream)
72.2, 65, 57.8, 43.3, 28.9, 21.7, 14.4, 7.2 Mbps (1 stream)
40 MHz BW (Long GI)
405, 364.5, 324, 243, 162, 121.5, 81, 40.5 Mbps (3 stream)
270, 243, 216, 162, 108, 81, 54, 27 Mbps (2 stream)
135, 121.5, 108, 81, 54, 40.5, 27, 13.5 Mbps (1 stream)
40 MHz BW (Short GI)
450, 405, 360, 270, 180, 135, 90, 45 Mbps (3 stream)
300, 270, 240, 180, 120, 90, 60, 30 Mbps (2 stream)
150, 135, 120, 90, 60, 45, 30, 15 Mbps (1 stream)
802.11a/g:
54, 48, 36, 24, 18, 12, 9, 6 Mbps
802.11b:
11, 5.5, 2, 1 Mbps
Infrastructure Mode
AOSS, WPA2-PSK (TKIP/AES), WPA/WPA2 mixed PSK, WPA-PSK (TKIP/AES), 64bit or 128-bit WEP, Mac Address Filter
USB Interface
Interface
Connector Type
Compliance
Other
Power Supply
Power Consumption
Dimensions
USB 2.0
Type A (plug)
5.0 V 500 mA (max 1000 mA)
External AC 100-240 V Universal, 50/60 Hz
About 13.2 W (Max)
212.2 x 183.2 x 34 mm (8.4 x 7.2 x 1.3 in.)
Weight 510 g (18 oz.)
Operating Environment 0 - 40° C (32 - 104° F), 20 - 80% (non-condensing)
- II -
Appendix A Specifications
802.11a Frequency Range
USA
Canada
5180-5240 MHz (Channels 36, 40, 44, 48)
802.11g Frequency Range
USA
Canada
2412-2462 MHz (Channels 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11)
- III -
Appendix B - Regulatory Compliance Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.This device is going to be operated in 5.15~5.25GHz frequency range, it is restricted in indoor environment only.
Important Note - FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user.
- IV -
Appendix B Regulatory Compliance Information
Industry Canada statement:
Industrie Canada déclaration:
This Class B digital apparatus complies with Canadian ICES-003.
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Ce dispositif est conforme à la norme CNR-210 d’Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes:
(1) le dispositif ne doit pas produire de brouillage préjudiciable, et
(2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.
Caution:
Prudence:
The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-channel mobile satellite systems.
Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.
Important Note - Radiation Exposure Statement:
Note Importante - Déclaration d’exposition aux radiations:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
This device has been designed to operate with an antenna having a maximum gain of [4.33] dB.
Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
- V -
Appendix B Regulatory Compliance Information
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
Ce dispositif a été conçu pour fonctionner avec une antenne ayant un gain maximal de dB [4.33].
Une antenne à gain plus élevé est strictement interdite par les règlements d’Industrie Canada.
L’impédance d’antenne requise est de 50 ohms.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peutfonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pourl’émetteur par
Industrie Canada. Dans le but de réduire les risques de brouillage radioélectriqueà l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que lapuissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire àl’établissement d’une communication satisfaisante.
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:
EN60950-1: 2006 +A11: 2009
Safety of Information Technology Equipment
EN50385 : (2002-08)
Product standard to demonstrate the compliance of radio base stations and fixed terminal stations for wireless telecommunication systems with the basic restrictions or the reference levels related to human exposure to radio frequency electromagnetic fields (110MHz - 40 GHz) - General public
EN 300 328 V1.7.1: (2006-10)
Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems;
Data transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the
R&TTE Directive
EN 301 893 V1.5.1: (2008-12)
Broadband Radio Access Networks (BRAN); 5 GHz high performance RLAN; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
EN 301 489-1 V1.8.1: (2008-04)
Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility
(EMC) standard for radio equipment and services; Part 1: Common technical requirements
EN 301 489-17 V2.1.1 (2009-05)
Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility
- VI -
Appendix B Regulatory Compliance Information
(EMC) standard for radio equipment; Part 17: Specific conditions for Broadband Data Transmission
Systems
This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies.
In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services.
This device may not be used for setting up outdoor radio links in France and in some areas the
RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France.
Česky [Czech]
Buffalo Technology Inc. tímto prohlašuje, že tento AirStation WZR-D1800H je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Dansk [Danish]
Undertegnede Buffalo Technology Inc. erklærer herved, at følgende udstyr AirStation WZR-D1800H overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch [German]
Hiermit erklärt Buffalo Technology Inc. dass sich das Gerät AirStation WZR-D1800H in
Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen
Bestimmungen der Richtlinie 1999/5/EG befindet.
Eesti [Estonian]
Käesolevaga kinnitab Buffalo Technology Inc. seadme AirStation WZR-D1800H vastavust direktiivi
1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
English
Hereby, Buffalo Technology Inc. declares that this AirStation WZR-D1800H is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Español [Spanish]
Por medio de la presente Buffalo Technology Inc. declara que el AirStation WZR-D1800H cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva
1999/5/CE.
- VII -
Appendix B Regulatory Compliance Information
Ελληνική [Greek]
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Buffalo Technology Inc. ΔΗΛΩΝΕΙ ΟΤΙ AirStation WZR-D1800H ΣΥΜΜΟΡΦΩΝΕΤΑΙ
ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
Français [French]
Par la présente Buffalo Technology Inc. déclare que l’appareil AirStation WZR-D1800H est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.
Italiano [Italian]
Con la presente Buffalo Technology Inc. dichiara che questo AirStation WZR-D1800H è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski [Latvian]
Ar šo Buffalo Technology Inc. deklarē, ka AirStation WZR-D1800H atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių [Lithuanian]
Šiuo Buffalo Technology Inc. deklaruoja, kad šis AirStation WZR-D1800H atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Nederlands [Dutch]
Hierbij verklaart Buffalo Technology Inc. dat het toestel AirStation WZR-D1800H in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Malti [Maltese]
Hawnhekk, Buffalo Technology Inc. , jiddikjara li dan AirStation WZR-D1800H jikkonforma malħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
Magyar [Hungarian]
Alulírott, Buffalo Technology Inc. nyilatkozom, hogy a AirStation WZR-D1800H megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Polski [Polish]
Niniejszym Buffalo Technology Inc. oświadcza, że AirStation WZR-D1800H jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português [Portuguese]
Buffalo Technology Inc. declara que este AirStation WZR-D1800H está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.
Slovensko [Slovenian]
Buffalo Technology Inc. izjavlja, da je ta AirStation WZR-D1800H v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.
- VIII -
Appendix B Regulatory Compliance Information
Slovensky [Slovak]
Buffalo Technology Inc. týmto vyhlasuje, že AirStation WZR-D1800H spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.
Suomi [Finnish]
Buffalo Technology Inc. vakuuttaa täten että AirStation WZR-D1800H tyyppinen laite on direktiivin
1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Svensk [Swedish]
Härmed intygar Buffalo Technology Inc. att denna AirStation WZR-D1800H står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv
1999/5/EG.
Taiwan:
SAR compliance has been established in typical laptop computer(s) with CardBus slot, and product could be used in typical laptop computer with CardBus slot. Other application like handheld PC or similar device has not been verified, may not comply with related RF exposure rules, and such use shall be prohibited.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this manual and of the computer manufacturer must therefore be allowed at all times to ensure the safe use of the equipment.
根據 NCC 低功率電波輻射性電機管制辦法：
第十二條：
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加
大功率或變更原設計之特性及功能。
第十四條：
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停
用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低
功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
해당 무선설비는 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없음
기종별
B 급 기기
( 가정용 정보통신기기 )
사 용 자 안 내 문
이 기기는 가정용 (B 급 ) 전자파적합기기로서 주
로 가정에서 사용하는 것을 목적으로 하며 , 모든
지역에서 사용할 수 있습니다 .
- IX -
Appendix C - Environmental Information
• The equipment that you have purchased has required the extraction and use of natural resources for its production.
• The equipment may contain hazardous substances that could impact health and the environment.
• In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the natural resources, we encourage you to use the appropriate take-back systems.
• The take-back systems will reuse or recycle most of the materials of your end life equipment in a sound way.
• The crossed-out wheeled bin symbol invites you to use those systems.
• If you need more information on collection, reuse, and recycling systems, please contact your local or regional waste administration.
- X -
Appendix D - GPL Information
The source code for Buffalo products that use GPL code is available at http://opensource.buffalo.jp/ .
- XI -
advertisement
Related manuals
advertisement