Laird Technologies SQGBT900US IntelligentBT4.0 Dual Mode USB Dongle Integration Guide

Intelligent BTv4.0 Dual-Mode USB

Dongle

Part # BT900-US

H

ARDWARE

I

NTEGRATION

G

UIDE

V

ERSION

1.0

Americas: +1-800-492-2320

Europe: +44-1628-858-940

Hong Kong: +852-2923-0610

BT900-US Hardware Integration Guide

Intelligent BTv4.0 Dual Mode Module www.lairdtech.com/bluetooth

Center: http://ews www.lairdtech.com/bluetooth

Laird Technologies

Americas: +1-800-492-2320

Europe: +44-1628-858-940

Hong Kong: +852 2923 0610

1.0


Intelligent BTv4.0 Dual Mode Module

R

EVISION

H

ISTORY

Initial Version


Laird Technologies

Americas: +1-800-492-2320

Europe: +44-1628-858-940

Hong Kong: +852 2923 0610



C

ONTENTS

Revision History ..................................................................................................................... 3

Contents ................................................................................................................................ 4

1 Overview and Key Features ................................................................................................ 5

1.1

Features & Benefits .......................................................................................................................................................... 5

1.2

Application Areas.............................................................................................................................................................. 5

2 Specification ..................................................................................................................... 6

2.1

Specification Summary ................................................................................................................................................... 6

3 FCC and IC Regulatory Statements ..................................................................................... 8

3.1

Power Exposure Information ........................................................................................................................................ 8

3.2

Federal Communication Commission Interference Statement ......................................................................... 8

3.3

Industry Canada statement ........................................................................................................................................... 9

4 EU Declarations of Conformity ........................................................................................... 9

4.1

BT900-US ............................................................................................................................................................................. 9

5 Ordering Information ...................................................................................................... 11

5.1

General Comments ......................................................................................................................................................... 11

6 Bluetooth SIG Qualification .............................................................................................. 11

Additional Assistance ................................................................................................................................................................. 12


Laird Technologies

Americas: +1-800-492-2320

Europe: +44-1628-858-940

Hong Kong: +852 2923 0610



1 O

VERVIEW AND

K

EY

F

EATURES

BT900 Series modules from Laird Technologies make it easy to add Classic BT and Bluetooth Low Energy (BLE) functionality to small, portable, power-conscious devices, including those powered by batteries. The fully approved, programmable modules feature Laird’s innovative, event-driven smart BASIC programming language, which significantly reduces OEM development risk and speeds time to market.

Based on the Cambridge Silicon Radio (CSR) 8811 silicon and a low power Cortex M3 microcontroller, the

BT900 modules provide exceptionally low power consumption with outstanding wireless range, all within a compact footprint of 19 mm x 12.5 mm. The modules incorporate all the hardware and firmware required to support development of Dual Mode applications, including:

Complete radio hardware

UART, I2C, SPI, ADC, and GPIO interfaces

Embedded BTv4.0 software stack

-

Classic BT profile - SPP

-

GATT Client & Peripheral Modes

What makes the modules truly innovative is smart BASIC, an event-driven programming language that enables standalone operation of the module. Laird has extended the implementation of smart BASIC from the popular BL6xx series of single mode BLE modules into the BT900 series. This allows developers the flexibility of utilising the Core and BLE specific smart BASIC functions from the BL6xx series to create fully interchangeable BLE applications between these product ranges.

Without the need for any external processor, a simple smart BASIC application encapsulates the complete end-to-end process of reading, writing, and processing of sensor data and then using Classic Bluetooth or

BLE to transfer it to / from any Bluetooth device. Ultimately smart BASIC accelerates initial development, creation of prototypes, and mass production by providing you with your own Bluetooth expert within the module.

In addition to carrying FCC modular, IC, CE and MIC approvals, BT900 modules are fully qualified as a

Bluetooth product, enabling designers to integrate the modules in devices without the need for further

Bluetooth testing. A low-cost developer’s kit including simple software tools simplifies module integration and guarantees the fastest route to market.

1.1

Features & Benefits

Bluetooth v4.0 - Dual Mode (Classic Bluetooth and BLE)

External or Internal Antennas smartBASIC programming language

Full Bluetooth EPL

Compact Footprint

Programmable TX power 8dBm to -20dBm

RX sensitivity: -90dBm

Ultra low power consumption

TX: 85 mA peak (at +8dBm)

Standby Doze: 2.7mA (see Note2 in Er not found.

Deep Sleep: 233uA

UART, GPIO, ADC, PWM, FREQ output, TIMERS, I2C, and SPI interfaces

Fast Time to Market

FCC, CE, IC, and Japan certified; other certs on request

No external components required

1.2

Application Areas

Medical devices

Wellness devices

Automotive Diagnostic

Equipment

Bar Code Scanners

Industrial Cable Replacement

Home automation


Laird Technologies

Americas: +1-800-492-2320

Europe: +44-1628-858-940

Hong Kong: +852 2923 0610



2 S

PECIFICATION

2.1

Specification Summary

Bluetooth®

Frequency

Transmit Power

Receive Sensitivity

Link Budget

Raw Data Rates (Air)

UART Interface

GPIO

I2C Interface

SPI

ADC Interface

PWM or FREQ output

Wi-Fi-BT coexistence

Classic Bluetooth

Bluetooth Low Energy

Classic Bluetooth

Bluetooth Low Energy smart BASIC smart BASIC application

V4.0 – Dual-Mode

2.402 - 2.480 GHz

+ 8 dBm (maximum)

Configurable down to -20 dBm

-90 dBm (typical)

98 dB

3 Mbps (Classic BT – BR/EDR)

TX, RX, CTS, RTS

DTR, DSR, DCD, RI can be implemented in smar tBASIC- using General Purpose I/O

Default 115200, N, ,8, 1

From 1,200 to 921600

RX buffer size (1024 bytes)

18 (maximum – configurable) lines.

O/P drive strength (4 mA)

Pull-up resistor (33 KOhms) control (via smart BASIC)

Read pin-level

1 (configurable from GPIO total). Up to 400 kbps

1 (configurable from GPIO total). Up to 4 Mbps

2 channels (configured from GPIO total).

Up to 12-bit resolution

Conversion time 2.0uS (at VCC 2.7V to 3.6V)

Reference voltage AVCC (external, same as VCC) pre-scaling to match BL600 ADC

Output a PWM or FREQ on up to 3 GPIO output pins.

PWM output duty cycle: 0%-100%

PWM output frequency: 500 kHz

FREQ output frequency: 0 MHz to 4 MHz (50% duty cycle)

3 dedicated pins

SPP (Serial Port Profile) –Greater than 500kbps

GATT Client & Peripheral – Any Custom Services

7 clients

5 clients

On-board programming language similar to BASIC

Via UART or Over the Air


Laird Technologies

Americas: +1-800-492-2320

Europe: +44-1628-858-940

Hong Kong: +852 2923 0610


Intelligent BTv4.0 Dual Mode Module smart BASIC runtime engine

FW upgrade

802.11 (Wi-Fi)

Self-contained Run Mode

Interactive Development

Mode

Supply

Current

User Configurable

Clocking

Dimensions

Operating

Storage

Lead Free

Warranty

Development Tools Development Kit

Utilities

Bluetooth®

FCC / IC / CE / MIC

Any that can be implemented using smart BASIC vSP – Virtual Serial Port for BLE – Command Mode

Only

Via UART

3 wire CSR schemes supported

(Unity-3 for classic BT, Unity-3e for BLE)

Selected by nAutoRUN pin status:

LOW (0V). Then runs $autorun$ ( smart BASIC application) if it exists.

HIGH (VCC). Then runs via at+run (and “file name” of smart BASIC application script).

Nominal 5VDC

Max Peak Current (TX Power @ +8 dBm TX): 85 mA

Standby Doze (waitevent) – 2.7mA (at 4MHz clock)

( Note 5 )

Deep Sleep – 233 uA (external signal wakeup) See

Note 5

User configurable clocking (40MHz, 20MHz, 4MHz), so user can reduce current consumption further.

50.7mm x 18.5mm x 10.4mm

-40°C to +85°C

-40°C to +85°C

Lead-free and RoHS compliant

One Year

Development board and free software tools

Windows, Android and iOS applications

UART Firmware Upgrade

Complete Declaration ID

All BT900 Series smart BASIC application. externally as per I2C standard. spare SIO pin within their smart BASIC application script allowing multi-dropping. smart BASIC runtime engine FW, but does not come loaded with any smart BASIC application script (as that is dependent on customer end application or use).

Laird provides many sample smart BASIC applications covering the services listed. smart BASIC runtime engine firmware (v9.1.2.0) has SIO (DIO default function) input pins that are

PULL-UP enabled by default. You may disable the internal PULL_UP through a smart BASIC


Laird Technologies

Americas: +1-800-492-2320

Europe: +44-1628-858-940

Hong Kong: +852 2923 0610


Intelligent BTv4.0 Dual Mode Module application script. Lower Power consumption may be achieved when all SIO pins are set as outputs and low (in your smart BASIC application script). In deep sleep 7uA can be achieved if all

SIO pins are set as output and low.

3 FCC

AND

IC R

EGULATORY

S

TATEMENTS

BT900-US SQGBT900US 3147A-BT900US

BT900-US

FORM FACTOR TX OUTPUT

USB Dongle 8 dBm Ceramic, Integrated

3.1

Power Exposure Information

Federal Communication Commission (FCC) Radiation Exposure Statement:

This EUT is in compliance with SAR for general population/uncontrolled exposure limits in ANSI/IEEE

C95.1-1999 and had been tested in accordance with the measurement methods and procedures specified in

OET Bulletin 65 Supplement C.

This transceiver must not be co-located or operating in conjunction with any other antenna, transmitter, or external amplifiers. Further testing / evaluation of the end product will be required if the OEM’s device violates any of these requirements.

The BT900 is fully approved for mobile and portable applications.

3.2

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.


Laird Technologies

Americas: +1-800-492-2320

Europe: +44-1628-858-940

Hong Kong: +852 2923 0610



The product comply with the US portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

3.3

Industry Canada statement

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada. Son fonctionnement est soumis aux deux conditions suivantes:

(1) Ce dispositif ne peut causer d'interférences; et(2) Ce dispositif doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil.

The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.

Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis et le

Canada établies pour un environnement non contrôlé. Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction aux expositions RF peut être augmentée si l'appareil peut être conservé aussi loin que possible du corps de l'utilisateur ou que le dispositif est réglé sur la puissance de sortie la plus faible si une telle fonction est disponible.

4 EU D

ECLARATIONS OF

C

ONFORMITY

4.1

BT900-US

Manufacturer:

Product:

EU Directive:

Conformity Assessment:

Laird

BT900-US

RTTE 1995/5/EC

Annex IV

Table 2: : : : Reference standards used for presumption of conformity

Ar ticle Number Requirement

3.1a Health and Safety

3.1b

Protection requirements with respect to electromagnetic compatibility

EN60950-1:2006+A11:2009+A1:2010+A12:2011

EN 301 489-1 V1.9.2 (2011-09)

EN 301 489-17 V2.2.1 (2012-09)

Emissions:

EN55022:2006/A1:2007 (Class B)

Immunity:

EN61000-4-2:2009


Laird Technologies

Americas: +1-800-492-2320

Europe: +44-1628-858-940

Hong Kong: +852 2923 0610



3.2

Means of the efficient use of the radio frequency spectrum

EN61000-4-3:2006/A1:2008/A2:2010

EN 300 328 V1.8.1 (2012-06)

We, Laird, declare under our sole responsibility that the essential radio test suites have been carried out and that the above product to which this declaration relates is in conformity with all the applicable essential requirements of Article 3 of the EU Directive 1999/5/EC, when used for its intended purpose.

Place of Issue:

Date of Issue:

Name of Authorized Person:

Laird

Saturn House, Mercury Park

Wooburn Green

HP100HH, United Kingdom tel: +44 (0)1628 858 940 fax: +44 (0)1628 528 382

July 2014

Andrew Dobbing, Engineering Manager

Signature:


Laird Technologies

Americas: +1-800-492-2320

Europe: +44-1628-858-940

Hong Kong: +852 2923 0610



5 O

RDERING

I

NFORMATION

N umber

BT900-US Single Mode Pluggable USB BLE Module featuring smart BASIC – integrated antenna

5.1

General Comments

This is a preliminary datasheet. Please check with Laird for the latest information before commencing a design.

If in doubt, ask.

6 B

LUETOOTH

SIG Q

UALIFICATION

The BT900-US module is listed on the Bluetooth SIG website as qualified End Products.

BT900

Laird

Technologie s

D023116 https://www.bluetooth.org/tpg/QLI_viewQDL.cfm?qid=23116

It is a mandatory requirement of the Bluetooth Special Interest Group (SIG) that every product implementing

Bluetooth technology has a Declaration ID. Every Bluetooth design is required to go through the qualification process, even when referencing a Bluetooth Design that already has its own Declaration ID. The Qualification

Process requires each company to registered as a member of the Bluetooth SIG – www.bluetooth.org

The following link provides a link to the Bluetooth registration page: https://www.bluetooth.org/login/register/

For each Bluetooth Design it is necessary to purchase a Declaration ID. This can be done before starting the new qualification, either through invoicing or credit card payment. The fees for the Declaration ID will depend on your membership status, please refer to the following webpage: https://www.bluetooth.org/en-us/test-qualification/qualification-overview/fees

For a detailed procedure of how to obtain a new Declaration ID for your design, refer to the following document: https://www.bluetooth.org/DocMan/handlers/DownloadDoc.ashx?doc_id=283698&vId=317486

To start the listing, go to: https://www.bluetooth.org/tpg/QLI_SDoc.cfm

You can then select your pre-paid Declaration ID from the drop down menu or go to the Purchase

Declaration ID page.

SIG invoice is paid.

Once all the relevant sections of step 1 are finished, complete steps 2, 3, and 4 as described in the help document. Your new Design will be listed on the SIG website and you can print your Certificate and DoC.

For further information please refer to the following training material: https://www.bluetooth.org/en-us/test-qualification/qualification-overview/listing-process-updates


Laird Technologies

Americas: +1-800-492-2320

Europe: +44-1628-858-940

Hong Kong: +852 2923 0610



Additional Assistance

Please contact your local sales representative or our support team for further assistance:

Laird Technologies Connectivity Products Business Unit

Support Centre: http://ews-support.lairdtech.com

Email: [email protected]

Phone: Americas: +1-800-492-2320 Option 2

Europe: +44-1628-858-940

Hong Kong: +852 2923 0610

Web: http://www.lairdtech.com/bluetooth


Laird Technologies

Americas: +1-800-492-2320

Europe: +44-1628-858-940

Hong Kong: +852 2923 0610



Laird is the world leader in the design and manufacture of customized, performance-critical products for wireless and other advanced electronics applications.

Laird Technologies partners with its customers to find solutions for applications in various industries such as:

Network Equipment

Telecommunications

Data Communications

Automotive Electronics

Computers

Aerospace

Military

Medical Equipment

Consumer Electronics

Laird offers its customers unique product solutions, dedication to research and development, as well as a seamless network of manufacturing and customer support facilities across the globe.

Americas: +1-800-492-2320 Option 2

Europe: +44-1628-858-940

Hong Kong: +852-2923-0610 www.lairdtech.com/bluetooth http://ews-support.lairdtech.com

CONN-HIGBT900

Copyright © 2014 Laird. All rights reserved.

The information contained in this manual and the accompanying software programs are copyrighted and all rights are reserved by

Laird Technologies, Inc. Laird Technologies, Inc. reserves the right to make periodic modifications of this product without obligation to notify any person or entity of such revision. Copying, duplicating, selling, or otherwise distributing any part of this product or accompanying documentation/software without the prior consent of an authorized representative of Laird Technologies, Inc. is strictly prohibited.

All brands and product names in this publication are registered trademarks or trademarks of their respective holders.

This material is preliminary

Information furnished by Laird Technologies in this specification is believed to be accurate. Devices sold by Laird Technologies are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. Laird Technologies makes no warranty, express, statutory, and implied or by description, regarding the information set forth herein. Laird Technologies reserves the right to change specifications at any time and without notice. Laird Technologies’ products are intended for use in normal commercial and industrial applications. Applications requiring unusual environmental requirements such as military, medical life-support or life-sustaining equipment are specifically not recommended without additional testing for such application.

Limited Warranty, Disclaimer, Limitation of Liability


Laird Technologies

Americas: +1-800-492-2320

Europe: +44-1628-858-940

Hong Kong: +852 2923 0610

Laird Technologies SQGBT900US IntelligentBT4.0 Dual Mode USB Dongle Integration Guide

Intelligent BTv4.0 Dual-Mode USB

Dongle

ARDWARE

NTEGRATION

UIDE

ERSION

EVISION

ISTORY

ONTENTS

VERVIEW AND

EY

EATURES

1.1

Features & Benefits

1.2

Application Areas

PECIFICATION

2.1

Specification Summary

AND

EGULATORY

TATEMENTS

3.1

Power Exposure Information

3.2

Federal Communication Commission Interference Statement

3.3

Industry Canada statement

ECLARATIONS OF

ONFORMITY

4.1

BT900-US

RDERING

NFORMATION

5.1

General Comments

LUETOOTH

UALIFICATION

Additional Assistance

Related manuals

Sumner Street Home Hardware

RL021804

MUL-T-LOCK TECHNOLOGIES

2AHH8ENTRWRT00

MUL-T-LOCK TECHNOLOGIES

2AHH8ENTRWRF00

MUL-T-LOCK TECHNOLOGIES

2AHH8ENTRRC00

Laird Technologies

SQGBT900

BT

900

Laird Technologies

TFB-1005

Table of contents