Philips 190cw7

19 inch TFT WXGA LCD Colour Monitor

190CW7CS/00

190CW7CS/27

190CW7CS/69

190CW7CS/75

190CW7CS/93

190CW7CS/96

190CW7CB/69

190CW7CB/93

190WV7CS/00

Chassis: HUDSON7

Horizontal frequencies

30 - 83 kHz

TABLE OF CONTENTS

Description Page

Important Safety Notice-----------------------------------2

Technical Data----------------------------------------------3

Installation---------------------------------------------------4

Troubleshooting--------------------------------------------5

On Screen Display--------------------------------------6~7

Lock/unlock,Aging,Factory mode-----------------------8

Philips Pixel Defect Policy -------------------------------9

Mechanical Instructions ----------------------------10~11

Color adjustment -----------------------------------------12

FAQs (Frequently Asked Questions)-------------13~14

Electrical instruction --------------------------------15~16

DDC Instructions&Serial Number ----------------17~23

DDC DATA --------------------------------------------24~25

Firmware Upgrade for CPU-

-----------------------26~27

Description Page

Failure Mode Of Panel -

---------------------------------28

Wiring Diagram------------------------------------------29

Block Diagram--------------------------------------------30

Scaler Diagram&C.B.A. ---------------------------31~37

Power Diagram & C.B.A. --------------------------38~41

Control Diagram&C.B.A. --------------------------42~43

General product specification--------------------44~65

Exploded View -------------------------------------------66

Repair tips--------------------------------------------67~68

Repair Flow chart-----------------------------------69~71

Safety Test Requirments-------------------------------72

Spare/ Recommended P arts List-----------------73~77

Different Parts List----------------------------------78~85

Revision List----------------------------------------------86

SAFETY NOTICE

ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS

AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC

EQUIPMENT CONTAINING HIGH VOLTAGES.

CAUTION: USE A SEPARATE ISOLATION TRANSFORMER FOR THIS UNIT WHEN SERVICING.

REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES

Published by BCU Monitors Printed in Suzhou Copyright reserved Subject to modification K Jul. 27 2006

GB

3138 106 10544

2

190CW7 LCD

Important Safety Notice

Proper service and repair isimportant to the safe, reliable operation of all HPConsumer Electronics Company**

Equipment. The service procedures recommended by HP and described in this service manual are effective methods of performing service operations. Some ofthese service operations require the use of tools specially designed for the purpose. The special tools should be used when and as recommended.

It is important to note that this manual contains various

CAUTIONS and NOTICES which should be carefully read in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It is also important to understand that these CAUTIONS and NOTICES ARE NOT

EXHAUSTIVE. HP could not possibly know, evaluate and advise the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, HP has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by HP must first satisfy himself thoroughly that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected.

* * Hereafter throughout this manual, HP Consumer

Electronics Company will bereferred to as HP.

WARNING

Critical components having special safety characteristics are identified with a bythe Ref. No. inthe parts list and enclosed within a broken line*

(where several critical components are grouped in one area) along with the safety symbol on the schematics or exploded views.

Use of substitute replacement parts which do not have the same specified safety characteristics may create shock, fire, or other hazards.

Under no circumstances should the original design be modified or altered without written permission from Philips.

Philips assumes no liability, express or implied, arising out of any unauthorized modification of design.

Servicer assumes all liability.

* Broken Line

FOR PRODUCTS CONTAINING LASER :

DANGERInvisible laser radiation when open.

AVOID DIRECT EXPOSURE TO BEAM.

CAUTIONUse of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

CAUTIONThe use of optical instruments with this product will increase eye hazard.

TO ENSURE THE CONTINUED RELIABILITY OF THIS

PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S

REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART

NUMBERS IN THE PARTS LIST SECTION OF THIS

SERVICE MANUAL.

Take care during handling the LCD module with backlight unit

- Must mount the moduleusing mounting holes arranged infour corners.

- Do not press onthe panel, edge of theframe strongly or electric shock as this will result in damage to the screen.

- Do not scratch orpress on the panel withany sharp objects, such as pencil or pen asthis may result in damage to the panel.

- Protect the module fromthe ESD as it maydamage the electronic circuit (C-MOS).

- Make certain that treatment person s body are grounded through wrist band.

- Do not leave themodule in high temperature andin areas of high humidity for a long time.

- Avoid contact with water as it may ashort circuit within the module.

- If the surface ofpanel become dirty, please wipe it off with a soft material. (Cleaning with a dirty or rough cloth may damage the panel.)

Technical Data

190CW7 LCD

LCD panel

Input DVI-D connector pin

Type NR.

Outside dimensions

Pitch ( mm )

: M190A1

: 427.2(w)

*277.4(h)*17.0(d) (Typ) mm

: 0.285 mm x 0.285 mm

Color pixel arrangement : RGB vertical stripes

Display surface : low reflection, antiglare with hard coating

Color depth

Backlight

Active area(WxH)

View angle (CR>10)

: 16.2M colors ( 6 bits+FRC)

: CCFL edge light system

: 410.4 x 256.5mm (19.05" diagonal)

: 75/75 (min), 85/85 (typ) for Horizontal & 70/

Contrast ratio

White luminance

Response time

Scanning frequencies

Hor.

Ver.

Video dot rate

Power input

Power consumption

Ambient temperature

70 (min), 80/80 (typ) for Vertical

: 850:1(Typ.) 500:1(Min.)

: Original color 230 nits (Min), 300 nits (Typ.)

: 5ms (typ)

: 30 - 83 K Hz

: 5 5 - 7 5 Hz

: <140 MHz

: 90-264 V AC, 50/60

± 2 Hz

: < 36W(typ.) maximum

: 0

°C - 35 °C

Power input connection

Power cord length : 1.8 M

Power cord type : 3 leads power cord with protective earth plug.

Power management

The monitor must comply with the Microsoft On Now specification, with two power management states, as defined by the VESA DPMS document.

The monitor must appropriately display the DPMS state.

Mode

Power-

On

Off

DC

Power Off

HSYNC VSYNC Video

On

Off

Pin Assignment

On

Off active blanked

N/A

Pwr-cons.

< 36 W(typ..)

34 W (typ.)

< 1 W

< 1 W

Indication

Green LED

Rec.

time

--

Pin No.

17

18

19

20

21

22

23

24

12

13

14

15

16

7

8

9

5

6

10

11

1

2

3

4

Description

T.M.D.S. data2-

T.M.D.S. data2+

T.M.D.S. data2 shield

No Connect

No Connect

DDC clock

DDC data

No Connect

T.M.D.S. data1-

T.M.D.S. data1+


No Connect

No Connect

+5V Power

Ground (for +5V) - Cable detect

Hot plug detect

T.M.D.S. data0-

T.M.D.S. data0+


No Connect

No Connect

T.M.D.S clock shield

T.M.D.S. clock+

T.M.D.S. clock-

Susceptibility of display to external environment

Amber LED < 3 s

Operating

- Temperature : 0 to 40 degree C

LED Off

- Humidity

- Altitude

: 80% max

: 0-3658m

- Air pressure : 600-1100 mBAR

Storage

- Temperature : -20 to 60 degree C

- Humidity

- Altitude

: 95% max

: 0-12192m


3

7

8

5

6

Pin No.

1

2

3

4

Assignment

Red video input

Green video input

Blue video input

GND

Cable detect

Red video GND

Green video GND

Blue video GND

Pin No.

9

10

11

12

Assignment

DDC +3.3V OR +5V

GND

GND

Serial data line (SDA)

13

14

15

H-sync

V-sync

Data clock line (SCL)

4

190CW7 LCD

Front View

Installation

Accessory Pack

Item Description

Power cord

VGA signal cable

EDFU pack

Connecting to Your PC

1) Connect the power cord to the back of the monitor firmly.

4

5

1

2

MENU

3

6 AUTO

Rear View

To switch monitor's power On and Off

To access OSD menu

/ to confirm

To move the adjust

To adjust brightness of the display

To adjust contrast of the display

Automatically adjust the horizontal position, vertical position, phase and clock setting special Mac adapter to one end of the monitor signal cable.

2) Connect to PC

(a) Turn off your computer and unplug its power cable.

(b) Connect the monitor signal cable to the video connector on the

(c) back of your computer.

Plug the power cord of your computer and your monitor into a

(d) nearby outlet.

Turn on your computer and monitor. If the monitor displays an image, installation is complete.

3

4

1

2

Kensington anti-thief lock

AC power input

DVI-D input

VGA input

Troubleshooting

190CW7 LCD

5

This page deals with problems that can be corrected by a user. If the problem still persists after you have tried thesesolutions, contact Philips customer service representative.

Common Problems

Having this problem

No Picture

(Power LED not lit)

No Picture

(Power LED is amber or yellow)

Screen says

ATTENTION

CHECK CABLE CONNECTION

Check these items

1.Make sure the power cord is plugged into the power outlet and into the back of the monitor.

2.First, ensure that the power button on the front of the monitor is in the OFF position, then press it to the ON position.

1.Make sure the computer is turned on.

2. Make sure the signal cable is properly connected to your computer.

3.Check to see if the monitor cable has bent pins.

4.The Energy Saving feature may be activated

1. Make sure the monitor cable is properly connected to your computer. (Also refer to the Quick Set-Up Guide).

2.Check to see if the monitor cable has bent pins.

3. Make sure the computer is turned on.

AUTO button not working properly

1.The Auto Function is designed for use on standard Macintosh or IBM-compatible

PCs running Microsoft Windows.

2. It may not work properly if using nonstandard PC or video card.

Imaging Problems

Display position is incorrect

Image vibrates on the screen

Vertical flicker appears

1.Press the Auto button.

2. Adjust the image position using the Horizontal Position and/or Vertical

Position in OSD Main Controls.

Check that the signal cable is properly connected to the graphics board or PC.

1. Press the Auto button.

2. Eliminate the vertical bars using the More Settings of Phase/Clock in OSD Main

Controls.

Horizontal flicker appears

1. Press the Auto button.

2. Eliminate the vertical bars using the More Settings of Phase/Clock in OSD Main

Controls.

The screen is too bright or too dark

An after-image appears

An after-image remains after the power has been turned off.

Green, red, blue, dark, and white dots

Remains

Adjust the contrast and brightness on OSD Main Controls. (The backlight of the

LCD monitor has a fixed life span. When the screen becomes dark or begins to flicker, please contact your dealer).

If an image remains on the screen for an extended period of time, it may be imprinted in the screen and leave an afterimage. This usually disappears after a few hours.

This is characteristic of liquid crystal and is not caused by a malfunction or deterioration of the liquid crystal. The after-image will disappear after a peroid of time.

The remaining dots are normal characteristic of the liquid crystal used in today's technology.

6

190CW7 LCD

On Screen Display

Description of the On Screen Display

This is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance of the monitors directly through an on-screen instruction window. The user interface provides userfriendliness and ease-of-use when operating the monitor.

Basic and simple instruction on the control keys.

When you press "menu" button on the front control of your monitor, the On-Screen Display (OSD) Main Controls window will pop up and you can then start making adjustments to your monitor's various features. Use the keys to make your adjustments.

The OSD Tree

Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want to work your way around the different adjustments later on.

On Screen Display

190CW7 LCD

7

8

190CW7 LCD

Front Control

Lock/Unlock,Aging,Factory Mode

After 15 seconds, bring up:

To Lock/Unlock OSD FUNCTION(User Mode)

The OSD function can be locked by pressing"OK"button(1) for more than 10 seconds, the screen shows following windows for 4 seconds.

Everytime when you press"OK" button, this message appears on the screen automatically.

ATTENTION SIGNAL

OSD MAIN CONTROLS

LOCKED

----------

---------repeatly

Connect Signal cable again=> go back to normal display

Access Factory Mode

1). Turn off monitor.

2).

[Push "AUTO" & "MENU" buttons at the same time and hold them]

+[Press "power" button untill comes out "Windows screen" ]

=> then release all buttons

3).Press "MENU" button, wait until the OSD menu with

Characters "HUDSON 190CW7 V0.15 2006-06-26" (below OSD menu) come on the Screen of the monitor.

Unlock OSD function

Unlocked OSD function can be released by pressing "OK" button for more than 10 seconds again.

ATTENTION SIGNAL

OSD MAIN CONTROLS

UNLOCKED

Access Aging Mode

Step 1 : D isconnect Interface Cable between Monitor and PC.

Step 2 : Turn off LCD monitor.Then

[Push "AUTO" & " MENU " buttons at the same time and hold them]+[Press power " " button untill comes out " AGING screen"] => then release all buttons.

Bring up:

Factory Mode indicator

Factory Menu

Cursor can move on gray color area

Hot key function: by pressing " LEFT " and " RIGHT " key

Simultaneously at User Mode (or Factory Mode)

(PS: The Offset R G B function can be used on reduce or eliminate snowy noise on the background when the resolution of video signal is 1440*900 vertical 60Hz. Slightly increase or decrease the value until snowy noise completely disappear.

ATTENTION

AGING...



ATTENTION

AGING...

Philips Pixel Defect Policy

Philips' Flat Panel Monitors Pixel Defect Policy

Philips strives to deliver the highest quality products. We use some of the industry's most advanced manufacturing processes and practice stringent quality control. However, pixel or sub pixel defects on the TFT LCD panels used in flat panel monitors are sometimes unavoidable. No manufacturer can guarantee that all panels will be free from pixel defects, but Philips guarantees that any monitor with an unacceptable number of defects will be repaired or replaced under warranty. This notice explains the different types of pixel defects and defines acceptable defect levels for each type. In order to qualify for repair or replacement under warranty, the number of pixel defects on a TFT LCD panel must exceed these acceptable levels. For example, no more than 0.0004% of the sub pixels on a 15" XGA monitor may be defective. Furthermore, Philips sets even higher quality standards for certain types or combinations of pixel defects that are more noticeable than others. This policy is valid worldwide.

190CW7 LCD

9

Black Dot Defects Black dot defects appear as pixels or sub pixels that are always dark or 'off'. These are the types of black dot defects:

Pixels and Sub pixels

A pixel, or picture element, is composed of three sub pixels in the primary colors of red, green and blue. Many pixels together form an image. When all sub pixels of a pixel are lit, the three colored sub pixels together appear as a single white pixel. When all are dark, the three colored sub pixels together appear as a single black pixel. Other combinations of lit and dark sub pixels appear as single pixels of other colors.

Types of Pixel Defects

Pixel and sub pixel defects appear on the screen in different ways. There are two categories of pixel defects and several types of sub pixel defects within each category. Bright dot defects appear as pixels or sub pixels that are always lit or

'on'. These are the types of bright dot defects:

One lit red, green or blue sub pixel

Two adjacent lit sub pixels:

- Red + Blue = Purple

- Red + Green = Yellow

- Green + Blue = Cyan

(Light Blue)

Three adjacent lit sub pixels

(one white pixel)

One dark sub pixel

Proximity of Pixel Defects

Two or three adjacent dark sub pixels

Because pixel and sub pixels defects of the same type that are near to one another may be more noticeable, Philips also specifies tolerances for the proximity of pixel defects.

Pixel Defect Tolerances

In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT LCD panel in a Philips flat panel monitor must have pixel or sub pixel defects exceeding the tolerances listed in the following tables.

BRIGHT DOT DEFECTS

MODEL

1 lit subpixel

2 adjacent lit subpixels

3 adjacent lit subpixels (one white pixel)

Distance between two bright dot defects*

ACCEPTABLE LEVEL

190CW7

3 or fewer

1 or fewer

0

25mm or more

Total bright dot defects of all types

3 or fewer

BLACK DOT DEFECTS

MODEL

1 dark subpixel

2 adjacent dark subpixels

ACCEPTABLE LEVEL

190CW7

5 or fewer

2 or fewer

3 adjacent dark subpixels(one white pixel) 0

Distance between two black dot defects*

Total black dot defects of all types

15 mm or more

5 or fewer

TOTAL DOT DEFECTS

MODEL

Total bright or black dot defects of all types

ACCEPTABLE LEVEL

190CW7

5 or fewer

Note:

* 1 or 2 adjacent sub pixel defects = 1 dot defect

10

190CW7 LCD

Front view

Mechanical Instruction

2: Remove the Back Cover Assy a. Unscrew 1 screws as shown in Fig.6.

b. Open 10 clicks on right and left side as shown in Fig.7 and Fig.8.

c. Open 7 clicks on bottom side as shown in Fig.9.

d. Open 7 clicks on top side as shown in Fig.10.

e. Remove the BACK COVER ASSY in Fig.11.

Fig.1

Fig.6

Back view

Fig.7

Fig.2

1. Remove the base .

a: Place the monitor face down on a smooth surface as Fig.3.

Be carefully to prevent the scratch and injury during the uninstallation. Press the botton and push the base as Fig.3.

Base

Botton

Fig.3

b: Drag the click to left and slip the stand bottom to left at the same time as Fig.4.

Fig.4

c: Remove the three screws and remove the hinge and stand top as

Fig.5.

Fig.5

Fig.8

Fig.9

Fig.10

Fig.11

Mechanical Instruction

3. Remove the Key board and bezel.

a.

Unscrew the 2 screws and disconnect the 1 cable to remove the

Key board as Fig.11.

b. Unscrew the 2 screws to remove the bezel as Fig. 12.

190CW7 LCD

11

Fig. 18

Fig.12

4. Remove the a.

SHIELDING ASSY , Scaler , Power board.

Unscrew the 4 screws on left and right side as Fig.13~14.

b. Disconnect the 1 cable carefully and turn the SHIELDING ASSY to right as Fig.15~16.

c. Unscrew the 14 screws to r emove the SHIELDING ASSY as

Fig. 17~18.

d. Disconnect the 4 cables to remove the Scaler and Power board.

Fig. 19

Fig.13

Fig. 20

In warranty, it is not allowed to disassembly the LCD panel, even the backlight unit defect.

Out of warranty, the replacment of backlight unit is a correct way when the defect is cused by backlight (CCFL,Lamp).

Fig.14

Fig.15

Fig. 16

Fig. 17

12

190CW7 LCD

Color Adjustment

Alignment procedure

1. Turn on the LCD monitor.

2.Turn on the Timing/pattern generator. See Fig.1

3. Preset LCD color Analyzer CA-110

-Remove the lens protective cover of probe CA-A30.

-Set measuring/viewing selector to measuring position for reset analyzer.(zero calibration) as Fig.2

- Turn on the color analyzer (CA-110)

-Press 0-CAL button to starting reset analyzer.

Fig. 1

4. Access Factory Mode


2).




Characters" HUDSON 190CW7 V0.15 2006-06-26" (below OSD menu) come on the Screen of the monitor. as shown in Fig3.


Fig. 3

4). Press "MENU" button, then select factory mode indicator by "LEFT" or "RIGHT" button .Press"MENU" button to bring up submenu windows as below:

Fig.5

5.Display

Press "LEFT" or "RIGHT" button to select . Change the value by "LEFT" or "RIGHT" key until the X,Y co-ordinates as below

5.1 White color adjustment

There are three factory preset white color 9300K, 6500K, sRGB.

Apply full white pattern, with brightness in 100 % position and the contrast control at 50 % position.

The 1931 CIE Chromaticity (color triangle) diagram (x,y) coordinate for the screen center should be:

Product spec.

9300K CIE coordinates X = 0.283

± 0.02

Y = 0.297

± 0.02

6500K/ sRGB CIE coordinates X = 0.313

± 0.02

Y = 0.329

± 0.02

sRGB CIE coordinates X = 0.313

± 0.02

Y = 0.329

± 0.02

Production alignment spec.


± 0.005

Y = 0.297

± 0.005


± 0.005

Y = 0.329

± 0.005


± 0.005

Y = 0.329

± 0.005

Quality Inspection spec.


± 0.015

Y = 0.297

± 0.015


± 0.015

Y = 0.329

± 0.015


± 0.015

Y = 0.329

± 0.015

Fig. 4

FAQs (Frequently Asked Questions)

190CW7 LCD

13

General FAQs

Q: When I install my monitor what should I do if the screen shows 'Cannot display this video mode'?

A: Recommended video mode for Philips 19 " : 1440 x 900 @60Hz.

1. Unplug all cables, then connect your PC to the monitor that you used previously.

2. In the Windows Start Menu, select Settings/Control Panel. In the Control Panel Window, select the Display icon. Inside the Display Control Panel, select the 'Settings' tab. Under the setting tab, in box labeled 'desktop area', move the slidebar to 1440 x 900 pixels (19").

3. Open 'Advanced Properties' and set the Refresh Rate to 60Hz, then click OK.

4. Restart your computer and repeat step 2 and 3 to verify that your PC is set at 1440 x 900@60Hz (19").

5. Shut down your computer, disconnect your old monitor and reconnect your Philips LCD monitor.

6. Turn on your monitor and then turn on your PC.

Q: What does 'refresh rate' mean in connection with an LCD monitor?

A: The refresh rate is of much less relevance for LCD monitors. LCD monitors display a stable, flicker-free image at 60Hz. There is no visible difference between 85Hz and 60Hz

Q: What are the .inf and .icm files on the CD-ROM? How do I install the drivers (.inf and . icm)?

A: These are the driver files for your monitor. Follow the instructions in your user manual to install the drivers. Your computer may ask you for monitor drivers (.inf and . icm files) or a driver disk when you first install your monitor. Follow the instructions to insert the ( companion CD-ROM) included in this package. Monitor drivers (.inf and . icm files) will be installed automatically.

Q: How do I adjust the resolution?

A: Your video card/graphic driver and monitor together determine the available resolutions. You can select the desired resolution under Windows®

Control Panel with the "Display properties".

Q: What if I get lost when I am making monitor adjustments?

A: Simply press the MENU button, then select 'Reset' to recall all of the original factory settings.

Q: What is the Auto function?

A: The

AUTO adjustment key restores the optimal screen position, phase and clock settings by pressing of a single button – without the need to navigate through OSD (On Screen Display) menus and control keys.

Note: Auto function is available in selected models only.

Q: My Monitor has no pow er (Power LED does not light up). What should I do?

A: Make sure the AC power cord is connected between the monitor and AC outlet, and click a key on keyboard/mouse to wake up the PC.

Q: Will the LCD monitor accept an interlaced signal under PC models?

A: No. If an Interlace signal is used, the screen displays both odd and even horizontal scanning lines at the same time, thus distorting the picture.

Q: What does the Refresh Rate mean for LCD?

A: Unlike CRT display technology, in which the speed of the electron beam is swept from the top to the bottom of the screen determines flicker, an active matrix display uses an active element (TFT) to control each individual pixel and the refresh rate is therefore not really applicable to LCD technology.

Q: Will the LCD screen be resistant to scratches?

A: A protective coating is applied to the surface of the LCD, which is durable to a certain extent (approximately up to the hardness of a 2H pencil). In general, it is recommended that the panel surface is not subject to any excessive shocks or scratches.

Q: How should I clean the LCD surface?

A: For normal cleaning, use a clean, soft cloth. For extensive cleaning, please use isopropyl alcohol. Do not use other solvents such as ethyl alcohol, ethanol, acetone,hexane, etc.

Q: Can I change the color setting of my monitor?

A: Yes, you can change your color setting through OSD control as the following procedures,

1. Press "MENU" to show the OSD (On Screen Display) menu.

2. Press "Left Arrow" to select the option "color" then press "MENU" to enter color setting, there are five settings as below.

a. 6500K; this setting features the panel closed to red-white color tone.

b. 9300K; this setting features the panel closed to blue-white color tone.

c. Original; this setting load the default panel setting in terms of color tone. (Note: different panel maker may feature a different color temperature*) d. User Define; the user can choose his/her preference color setting by adjusting red, green, blue color.

e. sRGB; this is a standard setting for ensuring correct exchange of colors between different device (e.g. digital cameras, monitors, printers, scanners, etc.)

Q: Can the Philips LCD Monitor be mounted on the wall?

A: Yes. Philips LCD monitors have this optional feature. For standard VESA mount holes on the rear cover allows the user to mount the Philips monitor on most of the VESA standard arms or accessories. We recommend to contact your Philips sales representative for more information.

Screen Adjustments

Q: What is the FPadjust program on the CD-ROM?

A: The FPadjust program generates alignment patterns that help you adjust monitor settings such as Contrast, Brightness, Horizontal Position,

Vertical Position, Phase and Clock for optimal performance.

Q: When I install my monitor, how do I get the best performance from the monitor?

A: 1. For best performance, make sure your display settings are set at 1440 x 900@60Hz for 19". Note: You can check the current display settings by pressing the OSD MENU button once. The current display mode is shown in OSD first page.

14

190CW7 LCD

FAQs (Frequently Asked Questions)

2. To install the Flat Panel Adjust (FPadjust) program located on the monitor setup CD-ROM, open the CD-ROM and double-click the FP_setup4.3.exe icon.

This will install FP Adjust automatically and place a shortcut on your desktop.

3. Run FPadjust by double clicking the shortcut. Follow the instructions step by step to optimize image performance with your system's video controller.

Q: How do LCDs compare to CRTs in terms of radiation?

A: Because LCDs do not use an electron gun, they do not generate the same amount of radiation at the screen surface.

Compatibility with other Peripherals

Q: Are Philips LCD monitors Plug-and-Play?

A: Yes, the monitors are Plug-and-Play compatible with Windows 95, 98, 2000 and XP.

Q: What is USB (Universal Serial Bus)?

A: Think of USB as a smart plug for PC peripherals. USB automatically determines resources (like driver software and bus bandwidth) required by peripherals.

USB makes necessary resources available without user intervention. There are three main benefits of USB. USB eliminates "case anxiety," the fear of removing the computer case to install circuit board cards -- that often requires adjustment of complicated IRQ settings -- for add-on peripherals. USB does away with "port gridlock." Without USB,PCs are normally limited to one printer, two Com port devices (usually a mouse and modem), one Enhanced Parallel

Port add-on (scanner or video camera, for example), and a joystick. More and more peripherals for multimedia computers come on the market every day.

With USB, up to 127 devices can run simultaneously on one computer. USB permits "hot plug-in." No need to shut down, plug in, reboot and run set up to install peripherals. No need to go through the reverse process to unplug a device. Bottom line: USB transforms today's "Plug-and-Pray" into true

Plug-and-Play! Please refer to glossary for more information about USB.

Q: What is a USB hub ?

A: A USB hub provides additional connections to the Universal Serial Bus. A hub's upstream port connects a hub to the host, usually a PC. Multiple downstream ports in a hub allows connection to another hub or device, such as a USB keyboard, camera or printer.

LCD Panel Technology

Q: What is a Liquid Crystal Display?

A: A Liquid Crystal Display (LCD) is an optical device that is commonly used to display ASCII characters and images on digital items such as watches, calculators, portable game consoles, etc. LCD is the technology used for displays in notebooks and other small computers. Like light-emitting diode and gas-plasma technologies, LCD allows displays to be much thinner than cathode ray tube(CRT) technology.LCD consumes much less power than LED and gas-displays because it works on the principle of blocking light rather than emitting it.

Q: What differentiates passive matrix LCDs from active matrix LCDs?

A: An LCD is made with either a passive matrix or an active matrix display grid. An active matrix has a transistor located at each pixel intersection, requiring less current to control the luminance of a pixel. For this reason, the current in an active matrix display can be switched on and off more frequently, improving the screen refresh time (your mouse pointer will appear to move more smoothly across the screen, for example). The passive matrix LCD has a grid of conductors with pixels located at each intersection in the grid.

Q: What are the advantages of TFT LCD compared with CRT?

A: In a CRT monitor, a gun shoots electrons and general light by colliding polarized electrons on fluorescent glass. Therefore, CRT monitors basically operate with an analog RGB signal. A TFT LCD monitor is a device that displays an input image by operating a liquid crystal panel. The TFT has a fundamentally different structure than a CRT: Each cell has an active matrix structure and independent active elements. A TFT LCD has two glass panels and the space between them is filled with liquid crystal. When each cell is connected with electrodes and impressed with voltage, the molecular structure of the liquid crystal is altered and controls the amount of inlet lighting to display images. A TFT LCD has several advantages over a CRT, since it can be very thin and no flickering occurs because it does not use the scanning method.

Q: Why is vertical frequency of 60Hz optimal for an LCD monitor?

A: Unlike a CDT monitor, the TFT LCD panel has a fixed resolution. For example, an XGA monitor has 1024x3 (R, G, B) x 768 pixels and a higher resolution may not be available without additional software processing. The panel is designed to optimize the display for a 65MHz dot clock, one of the standards for

XGA displays. Since the

Q: What kind of wide-angle technology is available? How does it work?

A: The TFT LCD panel is an element that controls/displays the inlet of a backlight using the dual-refraction of a liquid crystal. Using the property that the projection of inlet light refracts toward the major axis of the liquid element, it controls the direction of inlet light and displays it. Since the refraction ratio of inlet light on liquid crystal varies with the inlet angle of the light, the viewing angle of a TFT is much narrower than that of a CDT. Usually, the viewing angle refers to the point where the contrast ration is 10. Many ways to widen the viewing angle are currently being developed and the most common approach is to use a wide viewing angle film, which widens the viewing angle by varying the refraction ratio. IPS (In Plane Switching) or MVA (Multi Vertical Aligned) is also used to give a wider viewing angle.

Q: Why is there no flicker on an LCD Monitor?

A: Technically speaking, LCDs do flicker, but the cause of the phenomenon is different from that of a CRT monitor -- and it has no impact of the ease of viewing. Flickering in an LCD monitor relates to usually undetectable luminance caused by the difference between positive and negative voltage. On the other hand, CRT flickering that can irritate the human eye occurs when the on/off action of the fluorescent object becomes visible. Since the reaction speed of liquid crystal in an LCD panel is much slower, this troublesome form of flickering is not present in an LCD display.

Q: Why is an LCD monitor virtually low of Electro Magnetic Interference?

A: Unlike a CRT, an LCD monitor does not have key parts that generate Electro Magnetic Interference, especially magnetic fields. Also, since an LCD display utilizes relatively low power, its power supply is extremely quiet.

Ergonomics, Ecology and Safety Standards

Q: What is the CE mark?

A: The CE (Conformite Europeenne) mark is required to be displayed on all regulated products offered for sale on the European market. This 'CE' mark means that a product complies with the relevant European Directive. A European Directive is a European 'Law' that relates to health, safety, environment and consumer protection, much the same as the U.S. National Electrical Code and UL Standards.

Q: Does the LCD monitor conform to general safety standards?

A: Yes. Philips LCD monitors conform to the guidelines of MPR-II and TCO 99/03 standards for the control of radiation, electromagnetic waves, energy reduction, electrical safety in the work environment and recyclability. The specification page provides detailed data on safety standards.

Electrical Instructions

1 Electrical characteristics

1.1 Interface signals

1). D-Sub Analog

Input signal : Video, Hsync., Vsync

Video : 0.7 Vp-p, input impedance, 75 ohm @DC

Sync. : Separate sync TTL level , input impedance 2.2k ohm terminate

Hsync Positive/Negative

Vsync Positive/Negative

Composite sync TTL level, input impedance 2.2k ohm terminate(Positive/Negative)

Sync on green video 0.3 Vp-p Negative (Video 0.7 Vp-p Positive)

2). Intel DVI Digital

Input signal : Four channel TMDS signal

1.2

Interface

1.2.1 D-Sub Cable

Length : 1.8 M +/- 50 mm (fixed) , fix in monitor and with transplant pin protect cover.

Connector type : D-Sub male with DDC2B pin assignments.

Blue connector thumb-operated jack screws

1.3

Timing requirement

1.3.1

Mode storing capacity

190CW7 LCD

15

Factory preset modes : 20

Preset modes : 40

Note:

User define modes

1.

: 24

Screen displays perfect picture at 17 factory-preset modes.

1.3.2Factory preset modes (20 modes)

H.Freq.

31.469

31.469

37.861

37.500

35.156

37.879

48.077

46.875

48.363

56.476

6

7

4

5

Item

1

2

3

8

9

10

VESA

VESA

VESA

VESA

Mode

DOS

VESA

VESA

VESA

VESA

VESA

Resolution V.Freq.

720x400 70.087

640x480

640x480

59.940

72.809

640x480

800x600

800x600

800x600

75.000

56.250

60.317

72.188

800x600

1024x768

1024x768

75.000

60.004

70.069

18

19

20

16

17

14

15

Item H.Freq.

11 60.023

12

13

67.500

47.712

55.935

70.635

35.000

49.700

60.000

79.976

64.744

Mode

VESA

VESA

VESA

VESA

VESA

MACINTOSH

MACINTOSH

VESA

VESA

VESA

Resolution

1024x768

1152x864

1360x768

1440x900

1440x900

640x480

832x624

V.Freq

75.029

75.000

60.015

59.887

74.984

67.000

75.000

1280x960

1280x1024

1400x1050

60.000

75.025

59.948

16

190CW7 LCD

Electrical Instructions

2 White color adjustment

There are three factory preset white color 9300K, 6500K, sRGB. Apply full white pattern, with brightness in 100 % position and the contrast control at 50 % position. The 1931 CIE Chromaticity (color triangle) diagram (x,y) coordinate for the screen center should be:

Product spec.


± 0.02

Y = 0.297

± 0.02


± 0.02

Y = 0.329

± 0.02


± 0.02

Y = 0.329

± 0.02



± 0.005

Y = 0.297

± 0.005


± 0.005

Y = 0.329

± 0.005


± 0.005

Y = 0.329

± 0.005



± 0.015

Y = 0.297

± 0.015


± 0.015

Y = 0.329

± 0.015


± 0.015

Y = 0.329

± 0.015

DDC Instructions

190CW7 LCD

17

General

DDC Data Re-programming

In case the DDC data memory IC or main EEPROM which storage all factory settings were replaced due to a defect, the serial numbers have to be re-programmed "Analog DDC IC, Digital DDC IC & EEPROM".

It is advised to re-soldered DDC IC and main EEPROM from the old board onto the new board if circuit board have been replaced, in this case the DDC data does not need to be re-programmed.

Additional information

Additional information about DDC (Display Data Channel) may be obtained from Video Electronics Standards Association (VESA).

Extended Display Identification Data(EDID) information may be also obtained from VESA.

Note: The alignment box has already build-in a batteries socket for using batteries (8~12V) as power source. Pull out the socket by remove four screws at the rear of box. Please do not forget that remove batteries after programming. The energy of batteries can only drive circuits for a short period of time.

To Printer port

DC 8~12V

To Monitor

D-sub/DVI cable

Power indicator

System and equipment requirements

1.

An i486 (or above) personal computer or compatible.

2.

Microsoft operation system Windows 95/98 .

Y ou have t o Install the EDID_PORT_Tool under Win2000/XP . As

Fig. 1 .

Fig. 3

Pin assignment

A. 15-pin D-Sub Connector

A. Cody the "UserPort.sys" to C:\WINNT\system32\drivers(win2000)

C:\WINDOWS\system32\drivers(winXP)

B. Running " io.exe" everytime, Before you start to programming edid data .

PIN No.

1

2

7

8

9

10

5

6

3

4

11

12

13

14

15

SIGNAL

Red video input

Green video input / sync on green

Blue video input

GND

GND - Cable detect

Red video GND

Green video GND

Blue video GND

DDC +3.3V or +5V

Logic GND

GND

Serial data line (SDA)

H-sync / H+V

V-sync

Data clock line (SCL)

B. Input DVI -D Connector pin

3.

EDID46.EXE program

4.

A/D Alignment kits (12NC: 3138 106 10396): inclusion : a. Alignment box x1 (Fig. 2) b. Printer cable x1 c. (D-Sub) to (D-Sub) cable x1

D. (D-Sub) to (DVI) cable x1

Fig. 2

Pin No.

7

8

5

6

3

4

1

2

9

10

11

12

13

18

19

20

21

14

15

16

17

22

23

24

Description

T.M.D.S. data2-

T.M.D.S. data2+


No Connect

No Connect

DDC clock

DDC data

No Connect

T.M.D.S. data1-

T.M.D.S. data1+


No Connect

No Connect

+5V Power

Ground (for +5V) - Cable detect

Hot plug detect

T.M.D.S. data0-

T.M.D.S. data0+


No Connect

No Connect

T.M.D.S clock shield

T.M.D.S. clock+

T.M.D.S. clock-

18

190CW7 LCD

DDC Instructions

Configuration and procedure

There is no Hardware DDC (DDC IC) anymore. Main EEPROM stores all factory settings and DDC data (EDID code) which is also called

Software DDC. The following section describes the connection and procedure for Software DDC application. The main EEPROM can be reprogrammed by enabling '' factory memory data write'' function on the

DDC program (EDID46.EXE).

Initialize alignment box

In order to avoid that monitor entering power saving mode due to sync will cut off by alignment box, it is necessary to initialize alignment box before running programming software

(EDID46.EXE). Following steps show you the procedures and connection.

Step 1: Supply 8-12V DC power source to the Alignment box by plugging a DC power cord .

Step 2: Connecting printer cable and D-Sub cable of monitor as Fig. 4

3. At the submenu, type the letter of your computer's hard disk drive followed by :EDID46 (for example, C:\EDID46, as shown in Fig. 6).

1

Fig. 6

4. Click OK button. The main menu appears (as shown in Fig. 7).

This is for initialize alignment box.

PC

1=Power connector

2=D-SUB connector

DC Power

8-12 V

1

2

Printer

Port

To

Monitor

To PC

Fig. 7

Fig. 4

Step 3: Installation of EDID46.EXE

Method 1: Start on DDC program

Start Microsoft Windows.

1. The Program"EDID46.EXE" in service manual cd-rom be copyed to C:\ .

2. Click , choose Run at start menu of Windows as shown

In Fig. 5.

Note 1: If the connection is improper, you will see the following error message (as shown in Fig. 8) before entering the main menu.

Meanwhile, the (read EDID) function will be disable. At this time, please make sure all cables are connected correctly and fixedly, and the procedure has been performed properly.

Fig. 8

Fig. 5

Note 2: During the loading, EDID46 will verify the EDID data which just loaded from monitor before proceed any further function, once the data structure of EDID can not be recognized, the following error message will appear on the screen as below. Please confirm following steps to avoid this message.

1. The data structure of EDID was incorrect.

2. DDC IC that you are trying to load data is empty.

3. Wrong communication channel has set at configuration setup windows.

4. Cables loosed or poor contact of connection.

Fig. 9

DDC Instructions

Re-programming Analog DDC IC

Step 1: After initialize alignment box, connecting all cables and box as shown in Fig. 10.

1=Power connector

PC

2=D-SUB connector

190CW7 LCD

19

Fig. 13

DC Power

8-12V

1

2

Printer

Port

To

Monitor

To PC

To PC Video port (D-sub)

Fig. 10

Step 3: Modify DDC data (verify EDID version, week, year)

Click (new function) icon from the tool bar, bring up

Step 1 of 9 as shown in Fig. 14 .

EDID46 DDC application provides the function selection and

Step 2: Read DDC data from monitor

1.

Click icon as shown in Fig. 11 from the tool bar to bring up the Channels "Configuration Setup" windows as shown in Fig. 11.

Click this button

Fig. 11

2. Select the DDC2Bi as the communication channel.

As shown in Fig. 12.

Select and fill out,

If necessary.

Step 4: Modify DDC data (Monitor Serial No.)

1.

Click Next , bring up Fig. 15.

Fig. 14

Fig. 12

3. Click OK button to confirm your selection.

4. Click icon (Read EDID function) to read DDC EDID data from monitor. The EDID codes will display on screen as shown in Fig. 13.

Fig. 15

20

190CW7 LCD

2.

Click Next , bring up Fig.16.

DDC Instructions

5.


3.


4.


Fig. 19

Fig. 16

6.


In this step, please confirm the Descriptor Data Type is

Monitor Range Limits, and all the items are same as below.

Fig. 17

Fig. 20

7.


Fig. 18

Fig. 21

DDC Instructions

8.


- Click Finish to exit the Step window.

- Serial number can be filled up at this moment (for example, TY

123456).

NOTE: You must modify the Serial NO. In step 9, otherwise the Serial

NO. In OSD Couldn't be modified correctly.

Step 5: Write DDC data

1. Configuration should be as Fig. 23. And press OK.

190CW7 LCD

21

Step 8: Modify serial number in OSD

1. Unzip the serial number.zip to your computer, then open the folder as shown in Fig.27.

2. If use Win98 OS, you can execute SN.exe directly.

If use Win2000 or XP OS, first, you must execute install.bat, then execute SN.exe

3. Set I2C bus(press the left-top button of operating window) as shown in Fig.28, then press " SET" button.

4. Set Block2 as shown in Fig.29

5. key in new serial number, then press " Write" button as shown in

Fig.29 , Click " WRITE" button.

6. It will appear "Serial Number Write OK" , Click "Enter" to finish it.

Fig. 22 Fig. 23



2).




3).Press "MENU" button, wait until the OSD menu with Characters

"HUDSON 190CW7 V0.15 2006-06-26" (below OSD menu) come on the Screen of the monitor. as shown in Fig24.

Fig.27

Fig.28

TY 123456

Fig. 24


4). Click (Write EDID) icon from the tool bar to write DDC data.

Then wait for 20-30 seconds ,DDC data will be finished Writing.

Step 6: Save DDC data

Sometimes, you may need to save DDC data as a text file for using in other IC chip. To save DDC data, follow the steps below:

1. Click (Save) icon (or click "file"-> "save as") from the tool bar and give a file name as shown in Fig. 25.

The file type is EDID46 file (*.ddc) which can be open in WordPad.

By using WordPad, the texts of DDC data & table (128 bytes, hex code) can be modified. If DDC TEXTS & HEX Table ar completely correct, it can be saved as .ddc flie to re-load it into DDC IC for DDC

Data application.

Fig.29

Step9:

1. Disconnect the monitor power cord and connect it again.

2. Press the OK button to bring up the OSD main manu.

3. Re-confirm the serial Number is updated as shown in Fig.30.

TY 123456

Fig.30

Fig. 25

Fig. 26

2.

Click Save.

Step 7: Exit DDC program

Pull down the File menu and select Exit as shown in Fig. 26.

22

190CW7 LCD

DDC Instructions

Re-programming Digital DDC IC

Step 1: After initialize alignment box, connecting all cables and box as shown in Fig. 31.

PC

1=DVI-D connector

2=D-sub connector

3=Power Plug

DC Power

Printer

Port

To

Monitor

3

D-sub to DVI-D cable

1

2

Step 2: Read DDC data from monitor

D-sub cable

Fig. 31

1.

Click icon as shown in Fig. 11 from the tool bar to bring up the Channels "Configuration Setup" windows as shown in Fig. 32.

Select and fill out,

If necessary.

Fig. 35

Fig. 36

Step 4: Modify DDC data (Monitor Serial No.)

1.


2.


3.


Click this button

Fig. 32

Fig. 37

4.


5.


Fig. 38

2. Select the DDC2Bi as the communication channel.

As shown in Fig. 33.

Fig. 33 Fig. 34

3. Click OK button to confirm your selection.

4. Click icon (Read EDID function) to read DDC EDID data from monitor. The EDID codes will display on screen as shown in Fig. 34.

Step 3: Modify DDC data (verify EDID version, week, year)

Click (new function) icon from the tool bar, bring up

Step 1 of 9 as shown in Fig. 35 .

EDID46 DDC application provides the function selection and text change (select & fill out) from Step 1 to Step 9.

Fig. 39

Fig. 40

6.


In this step, please confirm the Descriptor Data Type is

Monitor Range Limits, and all the items are same as below.

7.


Philips 190CW

Fig. 41 Fig. 42

DDC Instructions

190CW7 LCD

23

8.


- Click Finish to exit the Step window.

- Serial number can be filled up at this moment (for example, TY

123456).

NOTE: You must modify the Serial NO. In step 9, otherwise the Serial

NO. In OSD Couldn't be modified correctly.

2.

Click Save.

Step 7: Exit DDC program

Pull down the File menu and select Exit as shown in Fig. 47.

Fig. 43 Fig. 44

Step 5: Write DDC data

1. Configuration should be as Fig. 40. And press OK.



2).




3).Press "MENU" button, wait until the OSD menu with Characters

"HUDSON 190CW7 V0.15 2006-06-26" (below OSD menu) come on the Screen of the monitor. as shown in Fig24.

Fig. 47

Step 8: Turn off the monitor, exit the factory mode.

Serial Number Definition

TY 123456


Fig. 45

3. Click (Write EDID) icon from the tool bar to write DDC data.

Then wait for 20-30 seconds ,DDC data will be finished Writing.

Step 6: Save DDC data

Sometimes, you may need to save DDC data as a text file for using in other IC chip. To save DDC data, follow the steps below:

1. Click (Save) icon (or click "file"-> "save as") from the tool bar and give a file name as shown in Fig. 46.

The file type is EDID46 file (*.ddc) which can be open in WordPad. By using WordPad, the texts of DDC data & table (128 bytes, hex code) can be modified. If DDC TEXTS & HEX Table ar completely correct, it can be saved as *.ddc flie to re-load it into DDC IC for DDC

Data application.

BOM Code

Panel Supplier

AUO

CPT

LPL(LG)

QDI

CMO

B Z 1 A 0 6 2 5 0 0 0 0 0 1

2

3

4

5

CODE

1

SERIAL NO

YEAR/WEEK

SERVICE VERSION CHANGE CODE

BOM CODE(BILL OF MATERIAL)CODE

SITE CODE(PRODUCTION CENTER)

BZ CODE(AR-CZECH REPUBLIC

VN-HUNGARY(SZR),BZ-SUZHOU

DS-DONGGUAN)

Fig.46

24

190CW7 LCD

DDC DATA

THE DISPLAY DATA CHANNEL (DDC_2B) CONTENT INCLUDING:

(FOR 190CW7 ANALOG FOR CMO PANEL)

**********************************************************************

EDID log file

**********************************************************************

Vendor/Product Identification

ID Manufacturer Name

ID Product Code

ID Serial Number

Week of Manufacture

Year of Manufacture

: PHL

: 084A (HEX.)

: 36F02 (HEX.)

: 27

: 2006

EDID Version, Revision

Version : 1

Revision : 3

Basic Display Parameters/Features

Video Input Definition : Analog Video Input

0.700V/0.300V (1.00Vpp) without Blank-to-Black Setup

Separate Sync

Composite Sync

Sync on Green no Serration required

Maximum H Image Size

Maximum V Image Size

Display Transfer Characteristic : 2.2

(gamma)

Feature Support (DPMS)

: 40

: 25

: no Standby no Suspend

Active Off

: RGB color display

: Detailed timing block 1

Display Type

Preferred Timing Mode

Color Characteristics

Red X coordinate

Red Y coordinate

Green X coordinate

Green Y coordinate

Blue X coordinate

Blue Y coordinate

White X coordinate

White Y coordinate

Established Timings

Established Timings I

: 0.64

: 0.334

: 0.285

: 0.599

: 0.153

: 0.076

: 0.313

: 0.328

Established Timings II

Manufacturer's timings

: 720 x 400 @70Hz (IBM,VGA)

640 x 480 @60Hz (IBM,VGA)

640 x 480 @67Hz (Apple,Mac II)

640 x 480 @72Hz (VESA)

640 x 480 @75Hz (VESA)

800 x 600 @56Hz (VESA)

800 x 600 @60Hz (VESA)

: 800 x 600 @72Hz (VESA)

800 x 600 @75Hz (VESA)


1024 x 768 @60Hz (VESA)

1024 x 768 @70Hz (VESA)

1024 x 768 @75Hz (VESA)

: 1152 x 870 @75Hz (Apple,Mac II)

Standard Timing Identification #1

Horizontal active pixels : 1152

Aspect Ratio

Refresh Rate

: 4:3

: 75



Aspect Ratio

Refresh Rate

: 4:3

: 60


Horizontal active pixels

Aspect Ratio

Refresh Rate



Aspect Ratio

Refresh Rate

Monitor Descriptor #2

Monitor Range Limits

Min. Vt rate Hz

Max. Vt rate Hz

Min. Horiz. rate kHz

Max. Horiz. rate kHz

Max. Supported Pixel

: 1440

: 16:10

: 60

: 1440

: 16:10

: 75

Detailed Timing #1

Pixel Clock (MHz)

H Active (pixels)

H Blanking (pixels)

V Active (lines)

V Blanking (lines)

: 106.5

: 1440

: 464

: 900

: 34

H Sync Offset (F Porch) (pixels): 80

H Sync Pulse Width (pixels) : 152

V Sync Offset (F Porch) (lines) : 3

V Sync Pulse Width (lines) : 6

H Image Size (mm)

V Image Size (mm)

: 408

: 255

H Border (pixels)

V Border (lines)

Flags

: 0

: 0

: Non-interlaced

: Normal Display, No stereo

: Digital Separate sync.

: Positive Vertical Sync.

: Negative Horizontal Sync.

: 55

: 75

: 30

: 83

: 140

No secondary GTF timing formula supported.


Monitor Name


Serial Number

: Philips 190CW

: TY 12345

: 0 Extension Flag

Check sum : 6A (HEX.)

**********************************************************************

EDID data (128 bytes)

**********************************************************************

0: 00 1: ff 2: ff 3: ff 4: ff 5: ff 6: ff 7: 00

8: 41 9: 0c 10: 4a 11: 08 12: 02 13: 6f 14: 03 15: 00

16: 1b 17: 10 18: 01 19: 03 20: 0e 21: 28 22: 19 23: 78

24: 2a 25: e1 26: 60 27: a3 28: 55 29: 49 30: 99 31: 27

32: 13 33: 50 34: 54 35: bf 36: ee 37: 80 38: 71 39: 4f

40: 81 41: 40 42: 95 43: 00 44: 95 45: 0f 46: 01 47: 01

48: 01 49: 01 50: 01 51: 01 52: 01 53: 01 54: 9a 55: 29

56: a0 57: d0 58: 51 59: 84 60: 22 61: 30 62: 50 63: 98

64: 36 65: 00 66: 98 67: ff 68: 10 69: 00 70: 00 71: 1c

72: 00 73: 00 74: 00 75: fd 76: 00 77: 37 78: 4b 79: 1e

80: 53 81: 0e 82: 00 83: 0a 84: 20 85: 20 86: 20 87: 20

88: 20 89: 20 90: 00 91: 00 92: 00 93: fc 94: 00 95: 50

96: 68 97: 69 98: 6c 99: 69 100: 70 101: 73 102: 20 103: 31

104: 39 105: 30 106: 43 107: 57 108: 00 109: 00 110: 00 111: ff

112: 00 113: 54 114: 59 115: 20 116: 31 117: 32 118: 33 119: 34

120: 35 121: 0a 122: 20 123: 20 124: 20 125: 20 126: 00 127: 6a

DDC DATA

190CW7 LCD

25

THE DISPLAY DATA CHANNEL (DDC_2B) CONTENT INCLUDING:

(FOR 190CW7 DIGITAL FOR CMO PANEL)

**********************************************************************

EDID log file

**********************************************************************

Vendor/Product Identification

ID Manufacturer Name : PHL

ID Product Code : 084A (HEX.)

ID Serial Number

Week of Manufacture

Year of Manufacture

: 36F02 (HEX.)

: 27

: 2006

EDID Version, Revision

Version

Revision

: 1

: 3

Basic Display Parameters/Features

Video Input Definition : Digital Video Input

Maximum H Image Size

Maximum V Image Size

: 40

: 25

Display Transfer Characteristic : 2.2

(gamma)

: no Standby Feature Support (DPMS) no Suspend

Active Off

: RGB color display

: Detailed timing block 1

Display Type

Preferred Timing Mode

Color Characteristics

Red X coordinate

Red Y coordinate

Green X coordinate

Green Y coordinate

Blue X coordinate

Blue Y coordinate

White X coordinate

White Y coordinate

Established Timings

Established Timings I

: 0.64

: 0.334

: 0.285

: 0.599

: 0.153

: 0.076

: 0.313

: 0.328

: 720 x 400 @70Hz (IBM,VGA)

640 x 480 @60Hz (IBM,VGA)


640 x 480 @72Hz (VESA)

640 x 480 @75Hz (VESA)

800 x 600 @56Hz (VESA)

800 x 600 @60Hz (VESA)

Established Timings II

Manufacturer's timings

: 800 x 600 @72Hz (VESA)

800 x 600 @75Hz (VESA)


1024 x 768 @60Hz (VESA)

1024 x 768 @70Hz (VESA)

1024 x 768 @75Hz (VESA)

: 1152 x 870 @75Hz (Apple,Mac II)



Aspect Ratio

Refresh Rate

Aspect Ratio

Refresh Rate

: 1152

: 4:3

: 75



: 4:3

: 60



Aspect Ratio

Refresh Rate



Aspect Ratio

Refresh Rate

Detailed Timing #1

Pixel Clock (MHz)

H Active (pixels)

H Blanking (pixels)

V Active (lines)

V Blanking (lines)

: 106.5

: 1440

: 464

: 900

: 34

H Sync Offset (F Porch) (pixels): 80

H Sync Pulse Width (pixels) : 152

V Sync Offset (F Porch) (lines) : 3

V Sync Pulse Width (lines)

H Image Size (mm)

V Image Size (mm)

H Border (pixels)

V Border (lines)

Flags

: 6

: 408

: 255

: 0

: 0

: Non-interlaced

: Normal Display, No stereo

: Digital Separate sync.

: Positive Vertical Sync.

: Negative Horizontal Sync.


Monitor Range Limits

Min. Vt rate Hz

Max. Vt rate Hz

Min. Horiz. rate kHz

Max. Horiz. rate kHz

Max. Supported Pixel

: 55

: 75

: 30

: 83

: 140

No secondary GTF timing formula supported.


Monitor Name


Serial Number

Extension Flag

Check sum

EDID data (128 bytes)

: 1440

: 16:10

: 60

: 1440

: 16:10

: 75

: Philips 190CW

: TY 123456

: 0

: E2 (HEX.)

********************************************************

********************************************************

0: 00 1: ff 2: ff 3: ff 4: ff 5: ff 6: ff 7: 00

8: 41 9: 0c 10: 4a 11: 08 12: 02 13: 6f 14: 03 15: 00

16: 1b 17: 10 18: 01 19: 03 20: 80 21: 28 22: 19 23: 78

24: 2a 25: e1 26: 60 27: a3 28: 55 29: 49 30: 99 31: 27

32: 13 33: 50 34: 54 35: bf 36: ee 37: 80 38: 71 39: 4f

40: 81 41: 40 42: 95 43: 00 44: 95 45: 0f 46: 01 47: 01

48: 01 49: 01 50: 01 51: 01 52: 01 53: 01 54: 9a 55: 29

56: a0 57: d0 58: 51 59: 84 60: 22 61: 30 62: 50 63: 98

64: 36 65: 00 66: 98 67: ff 68: 10 69: 00 70: 00 71: 1c

72: 00 73: 00 74: 00 75: fd 76: 00 77: 37 78: 4b 79: 1e

80: 53 81: 0e 82: 00 83: 0a 84: 20 85: 20 86: 20 87: 20

88: 20 89: 20 90: 00 91: 00 92: 00 93: fc 94: 00 95: 50

96: 68 97: 69 98: 6c 99: 69 100: 70 101: 73 102: 20 103: 31

104: 39 105: 30 106: 43 107: 57 108: 00 109: 00 110: 00 111: ff

112: 00 113: 54 114: 59 115: 20 116: 31 117: 32 118: 33 119: 34

120: 35 121: 36 122: 0a 123: 20 124: 20 125: 20 126: 00 127: e2

26

190CW7 LCD

Firmware Upgrade for CPU

Configuration and procedure

"Easywriter " The software is provided by Novatek to upgrade the firmware of CPU.

It is a windows-based program, which cannot be run in MS-DOS.

DDC2BI_ISP TOOL (3138 149 53161) is for the interface between

"Parallel Port of PC" and "15 pin-D-SUB connector of Monitor".

System and equipment requirements

1.

An i486 (or above) personal computer or compatible.

2.

Microsoft operation system Windows 95/98/2000/XP.

3.

ISP Software " Easywrite "

4.

DDC2BI_ISP TOOL (3138 106 10396) as shown in Fig. 1

Fig. 4

Step 5 :Copy the 190CW7_NT68663_M190A1_EU_4C70_Org_V015 to C:\190CW7 as shown in Fig. 5 .

D-SUB to monitor

Parallel Port to Print Port in PC

Fig. 1

Fig. 5

5.

Connect in Fig. 2.

DDC2BI_ISP TOOL and Mains cord to Monitor as shown

PC

Monitor (A)

190CW7-Monitor (B)

D-Sub

Update the firmware

1.

Double click the Easywriter.exe icon in desktop then appears window as shown in Fig.7 .

Connect to

Mains cord

Connect to Mains cord at this moment.

ISP box

Video cable

Fig.2

6. Install and setup the Easywriter program

Step 1 : Make a folder in your PC as shown in Fig. 3.

For example : C:\190CW7

Step 2 : Copy ISP Software Easywriter .zip

into your folder as shown in Fig.3.

Step 3 : Unzip Easywriter.zip into your folder as shown in Fig. 3.

Step 4 : Double click the EasyWriterV2.10p2 icon to install the

Application as Fig. 4.

Fig. 6

Fig. 3 Fig. 7

2.

Press the Load hex then select the hex as shown in Fig. 8.

Firmware Upgrade for CPU

190CW7 LCD

27

If there is a warring message coming as shown in Fig 12. , you have to check the AC power, Video cable, or Novatek MCU.

Fig. 8

3 Press the AUTO to running program , the firmware be updated as shown in Fig. 9~10.

Fig. 9

Fig. 12

5 Check the firmware version


2).



=> then release all buttons.

3).Press "MENU" button, wait until the OSD menu come on the

Screen of the monitor.You will find, after upgrade, the version have already changed from The former"HUDSON 190CW7

V0.06 2006-06-01" to the Present "HUDSON 190CW7 V0.15

2006-06-26 as shown in Fig. 13 and Fig. 14.

Fig. 10

4 Press the file --> exit to end program , as shown in Fig. 11.


Fig. 13

Fig. 11


4) Turn off the monitor, exit the factory mode.

Fig. 14

28

190CW7 LCD

Go to cover page

Quick reference for failure mode of LCD panel

Failure Mode Of Panel this page presents problems that could be made by LCD panel.

It is not necessary to repair circuit board. Simply follow the mechanical instruction on this manual to eliminate failure by replace LCD panel.

Polarizer has bubbles

Failure description

Phenomenon

Vertical block defect

Vertical dim lines

Polarizer has bubbles

Foreign material inside polarizer. It shows liner or dot shape.

Vertical lines defect

(Always bright or dark)

Concentric circle formed

Horizontal block defect

Bottom back light of LCD is brighter than normal

Horizontal dim lines

Back light un-uniformity

Horizontal lines defect

(Always bright or dark)

Has bright or dark pixel

Backlight has foreign material.

Black or white color, liner or circular type

29

CN406

1

12

CN101

1

CN801

CN802

CN803

CN804

Wiring Diagram

190CW7 LCD 29

30 190CW7 LCD

Block Diagram

Scaler Diagram-1

190CW7 LCD 31

32 190CW7 LCD

Scaler Diagram-2

Scaler Diagram-3

190CW7 LCD 33

34 190CW7 LCD

Scaler Diagram-4

Scaler Diagram-5

190CW7 LCD 35

36 190CW7 LCD

Scaler Board C.B.A.-1

Scaler Board C.B.A.-2

190CW7 LCD 37

38 190CW7 LCD

Power Diagram-1

Power Diagram-2

190CW7 LCD 39

40 190CW7 LCD

715G1899-B-PHI

715G1899-B-PHI

Power Board C.B.A.-1

Power Board C.B.A.-2

715G1899-B-PHI

715G1899-B-PHI

190CW7 LCD 41

42 190CW7 LCD

Control Diagram

Control Board C.B.A.

190CW7 LCD

43

44 190CW7 LCD

GENERAL PRODUCT SPECIFICATION

HUDSON7-190CW7

GENERAL PRODUCT

SPECIFICATION

. ANALOG AND DIGITAL DUAL INPUT

. AUTO PICTURE ADJUSTMENT

.

20 FACTORY PRESET MODES AND 40 PRESET MODES WHICH

CAN BE RECOVERED TO PRESET MODES, 24 USER MODES.

. USER FRIENDLY OSD DISPLAY FOR MODE IDENTIFICATION

/ADJUSTMENT

. MAX. RESOLUTION WXGA+ ( 1440 * 900 ) NON-INTERLACED AT 75 HZ

. 19"W COLOR TFT LCD FLAT PANEL

. EASY TILT BASE

. FULL RANGE POWER SUPPLY 100 - 240 VAC

. CE ENVIRONMENTAL POLICY

. ANTI-GLARE TO REDUCE LIGHT REFLECTION

. POWER MANAGEMENT CAPABILITY

. SOG SUPPORT

.

TCO 03 99

. SMART CONTROL & SMART MANAGEMENT REQUIREMENT

. WEEE REQUIREMENT

. RoHS REQUIREMENT

2006-06-22

19 inch TFT WXGA LCD Monitor

TYPE : 190CW7CS/00

BRAND : PHILIPS

22

2006-06-22

590

8639 000 17256

1

GENERAL PRODUCT SPECIFICATION(Continued) 190CW7 LCD

45

CONTENTS

1

2

2.1

2.2

2.3

FOREWORD

PRODUCT PROFILE

LCD

S

CANNING FREQUENCIES

A

MBIENT TEMPERATURE

: 0 °C - 35 °C

3

3.1

3.2

3.3

3.4

3.5

3.6

3.7

3.8

ELECTRICAL CHARACTERISTICS

I

NTERFACE SIGNALS

I

NTERFACE

T

IMING REQUIREMENT

H

ORIZONTAL SCANNING

V

ERTICAL SCANNING

P

OWER INPUT CONNECTION

P

OWER MANAGEMENT

D

ISPLAY IDENTIFICATION

4

5

4.1

4.2

4.3

4.4

4.5

4.6

VISUAL CHARACTERISTICS

T

EST CONDITIONS

B

RIGHTNESS

I

MAGE SIZE

B

RIGHTNESS UNIFORMITY

C

HECK

C

ROSS TALK

(S)

W

HITE COLOR ADJUSTMENT

MECHANICAL CHARACTERISTICS

5.10

5.11

5.12

5.13

5.6

5.7

5.8

5.9

5.1

5.2

C

OSMETIC

P

HILIPS

TPV ID

M

ECHANICAL DATA FILES

P

RO

E

FILES REQUIRED

5.3

L

OCATION OF

P

HILIPS LOGO

P

ER

P

HILIPS MAKE

-

UP SHEET

G

AP BETWEEN PANEL AND FRONT BEZEL

< 1.2

MM

L

OCATION OF

C

ONTROL ICONS

-

5.4

C

OLOR FOR RESIN

/

PAINT

P

ER

P

P

ER

P

HILIPS MAKE

HILIPS

-

G

RAPHIC

UP SHEET

S

HEET

5.5

R

ESINS

I

T

T

F PAINT IS USED

P

P

P

LASTIC MOLD TOOLING

LASTICS FLAMMABILITY

EXTURE

L

ABEL

/G

LOSSING OF HOUSING

T

ILT AND SWIVEL BASE

RODUCT DIMENSION

RANSPORTATION

/ W

EIGHT

2006-06-22


TYPE : 190CW7CS/00

BRAND : PHILIPS

22

2006-06-22

590

8639 000 17256

2

46

190CW7 LCD

GENERAL PRODUCT SPECIFICATION(Continued)

5.10

5.11

5.12

5.13

5.14

5.5

5.6

5.7

5.8

5.9

G

AP BETWEEN PANEL AND FRONT BEZEL

< 1.2

MM

L

OCATION OF

C

ONTROL ICONS

-

5.4

C

OLOR FOR RESIN

/

PAINT

P

ER

P

P

ER

P

HILIPS MAKE

HILIPS

-

G

RAPHIC

UP SHEET

S

HEET

I

R

ESINS

F PAINT IS USED

P

LASTIC MOLD TOOLING

P

LASTICS FLAMMABILITY

T

EXTURE

/G

LOSSING OF HOUSING

T

ILT AND SWIVEL BASE

L

ABEL

P

RODUCT DIMENSION

/ W

EIGHT

T

RANSPORTATION

P

ALLET

/ C

ONTAINER LOADING

6

6.1

6.2

6.3

6.4

ENVIRONMENTAL CHARACTERISTICS

S

USCEPTIBILITY OF DISPLAY TO EXTERNAL ENVIRONMENT

T

RANSPORTATION TESTS

D

ISPLAY DISTURBANCES FROM EXTERNAL ENVIRONMENT

D

ISPLAY DISTURBANCES TO EXTERNAL ENVIRONMENT

7

7.1

RELIABILITY

M

EAN

T

IME

B

ETWEEN

F

AILURES

8

9

8.1

QUALITY ASSURANCE REQUIREMENTS

A

CCEPTANCE TEST

Philips' Flat Panel Monitors Pixel Defect Policy

2006-06-22


TYPE : 190CW7CS/00

BRAND : PHILIPS

22

2006-06-22

590

8639 000 17256

3


47

1 FOREWORD

This specification describes a 19"W WXGA+ multi-scan color TFT LCD monitor with max. resolution up to

1440*900/ 76 75 Hz non-interlaced.

All optical characteristics (including WHITE-D, Brightness, and so on) are determined according to panel specification after warming up approximate 30 minutes that brightness stability is optimal, and follow strictly after panel specification.

2 PRODUCT PROFILE

This display monitor unit is a color display monitor enclosed in integrated tilt base.

PHILIPS global styling cabinet which has an

2.1

LCD

2.1.1

Type NR.

Outside dimensions

: M190A1

: 427.2(w)*277.4(h)*17.0(d) (Typ) mm

Pitch ( mm ) : 0.285 mm x 0.285 mm

Color pixel arrangement : RGB vertical stripes

Display surface

Color depth

: low reflection, antiglare with hard coating

: 16.2M colors ( 6 bits+FRC)

Backlight

Active area(WxH)

View angle (CR>10)

Contrast ratio

White luminance

: CCFL edge light system

: 410.4 x 256.5mm (19.05" diagonal)

: 75/75 (min), 85/85 (typ) for Horizontal & 70/70 (min), 80/80

: 850:1(Typ.) 500:1(Min.)

: Original color 230 nits (Min), 300 nits (Typ.)

(typ) for Vertical

Gate IC

Source IC

Response time

:

:

: 5ms (typ)

2.2

Scanning frequencies

Hor.

Ver.

: 30 - 83 K Hz

: 5 5 - 7 5 Hz

Video dot rate

Power input

: <140 MHz

: 90-264 V AC, 50/60 ± 2 Hz

Power consumption : < 36W(typ.) maximum

2.3

3

3.1

Ambient temperature : 0 °C - 35 °C

Electrical characteristics

Interface signals

1). D-Sub Analog

Input signal : Video, Hsync., Vsync

Video : 0.7 Vp-p, input impedance, 75 ohm @DC

Sync. : Separate sync TTL level , input impedance 2.2k ohm terminate

Hsync Positive/Negative

Vsync Positive/Negative

Composite sync TTL level, input impedance 2.2k ohm terminate

Sync on green video 0.3 Vp-p Negative (Video 0.7 Vp-p Positive)

(Positive/Negative)

2006-06-22


TYPE : 190CW7CS/00

BRAND : PHILIPS

22

2006-06-22

590

8639 000 17256

4

48 190CW7 LCD


2). Intel DVI Digital

Input signal : Four channel TMDS signal

3.2

3 .2.1

Interface

D-Sub Cable

Length : 1.8 M +/- 50 mm (fixed) , fix in monitor and with transplant pin protect cover.

Connector type : D-Sub male with DDC2B pin assignments.

Blue connector thumb-operated jack screws pin assignment :

3.2.2

DVI Cable

PIN No.

8

9

6

7

10

11

12

13

14

15

3

4

5

1

2

SIGNAL

Red

Green/ SOG

Blue

Sense (GND)

Cable Detect (GND)

Red GND

Green GND

Blue GND

DDC +3.3V or +5V

Logic GND

Sense (GND)

Bi-directional data

H/H+V sync

V-sync

Data clock

The input signals are applied to the display through DVI-D cable.

Length : 1.8 M +/- 50mm (fixed)

Connector type : DVI-D male with DDC2B pin assignments

White connector thumb-operated jack screws pin assignment :

2006-06-22


TYPE : 190CW7CS/00

BRAND : PHILIPS

22

2006-06-22

590

8639 000 17256

5


49

Note the mark "*" for DVI-I to Dsub only

3.2.3

Pin No.

18

19

20

21

15

16

17

10

11

12

13

14

3

4

5

1

2

8

9

6

7

22

23

24

C1

C2

C3

C4

C5

TMDS data2-

TMDS data2+

TMDS data2 shield

NC

NC

DDC clock

DDC data

* Analog V-sync

TMDS data1-

Description

TMDS data1+

TMDS data1 shield

NC

NC

+5V

Ground(return for +5V and H/V-sync)(Cable Detect)

Hot plug detect

TMDS data0-

TMDS data0+

TMDS data0 shield

NC

NC

TMDS clock shield

TMDS clock+

TMDS clock-

* Analog R

* Analog G

* Analog B

* Analog H-sync

* Analog GND (Analog R, G, B return)

Software control functions via OSD/control adjustable functions:

OSD control bottom sequence.

2006-06-22

Auto - Left (Brightness) - Power - Right (Contrast) - Menu


TYPE : 190CW7CS/00

BRAND : PHILIPS

22

2006-06-22

590

8639 000 17256

6

50 190CW7 LCD


(1) PC Analog Signal Input Mode

Adjustable functions:

1 st

LEVEL

MONITOR SETUP

Exit

Brightness & Contrast

Color

Position

2 nd

LEVEL

Brightness

Contrast

Original Color, 9300K,6500K, sRGB, User

Define

Horizontal

Vertical

Input Selection

More Settings

Analog [ Digital ]

Language

Phase/ Clock

OSD Settings

3rd LEVEL

/00,/05 : English, Spanish, French,

German, Italian and Russian

/27 : English, French, Spanish,

Portuguese & S. Chinese

/69,/75,/93,/96 : English, Spanish,

French, German, Italian and S. Chinese

Phase

Clock

Horizontal

Vertical

Reset

Serial No.:

(Serial No.)

Timing Mode

Up/Down left / right to Move and to Adjust,ok menu to

Confirm

No

Yes

2006-06-22


TYPE : 190CW7CS/00

BRAND : PHILIPS

22

2006-06-22

590

8639 000 17256

7


51

(2) Digital interface OSD :

Adjustable functions:

1 st

LEVEL

MONITOR SETUP

Exit

Brightness & Contrast

Color

Position

Input Selection

More Settings

Reset

Serial No.:

(Serial No.)

Timing Mode

Up/Down left / right to

Move and to Adjust,ok menu to Confirm

2 nd

LEVEL 3rd LEVEL

Brightness

Contrast

Original Color, 9300K,6500K, sRGB, User

Define

Horizontal

Vertical

Analog,[ Digital]

Language

Phase/ Clock

OSD Settings

/00 : English, Espanol, Frencais,

Deutsch, Italiano, , Russian

/27 : English, Espanol, Frencais,

Portuguess, S-Chinese

/69,/75,/93,/96 : English, Espanol,

Frencais, Deutsch, Italiano, , S-Chinese

Phase

Clock

Horizontal

Vertical

No

Yes

Remark : < to Adjust > / < to Move > - < to Confirm >

Remark : Color Temperature factory default setting = see 190CW7 SKU.

2006-06-22


TYPE : 190CW7CS/00

BRAND : PHILIPS

22

2006-06-22

590

8639 000 17256

8

52 190CW7 LCD


3.3

3.3.1

Timing requirement

Mode storing capacity

7

8

5

6

9

10

Note:

Item

1

3.3.2

H.Freq.

(KHz)

31.469

Factory preset modes

Preset modes

User define modes

1.

2.

:

: 20

40

: 24

Screen displays perfect picture at 17 factory-preset modes.

Screen displays visible picture with OSD warning when input modes are the

33 preset modes

Factory preset modes (20 modes)

Mode

DOS

Resolution

720x400

V.Freq.

(Hz)

70.087

Item

11

H.Freq.

(KHz)

60.023

Mode

VESA

Resolution

1024x768

2

3

4

31.469

37.861

37.500

VESA

VESA

VESA

640x480

640x480

640x480

59.940

72.809

75.000

12

13

14

67.500

47.712

55.935

VESA

VESA

VESA

1152x864

1360x768

1440x900

35.156

37.879

48.077

46.875

48.363

56.476

VESA

VESA

VESA

VESA

VESA

VESA

800x600

800x600

800x600

800x600

1024x768

1024x768

56.250

60.317

72.188

75.000

60.004

70.069

15

16

17

18

19

20

70.635

35.000

49.700

60.000

79.976

64.744

VESA

MACINTOSH

MACINTOSH

VESA

VESA

VESA

1440x900

640x480

832x624

1280x960

1280x1024

1400x1050

74.984

67.000

75.000

60.000

75.025

59.948

V.Freq

. (Hz)

75.029

75.000

60.015

59.887

2006-06-22


TYPE : 190CW7CS/00

BRAND : PHILIPS

22

2006-06-22

590

8639 000 17256

9

GENERAL PRODUCT SPECIFICATION(Continued) 190CW7 LCD 53

MODE NO.

RESOLUTION

Dot clock(MHz) f h

A ( us )

B ( us )

C ( us )

D ( us )

E ( us ) f v

O (ms )

P ( ms )

Q (ms )

R ( ms )

S ( ms )

SYNC. H/V

POLARITY

SEP . SYNC

3.3.3

MODE NO.

RESOLUTION

Dot clock(MHz) f h

A ( us )

B ( us )

C ( us )

D ( us )

E ( us ) f v

O (ms )

P ( ms )

Q (ms )

R ( ms )

S ( ms )

SYNC. H/V

POLARITY

SEP . SYNC

Preset Modes (33 40 modes)

1

640 x 350

25.175

31.469kHz

31.778(800 dots)

3.813(96 dots)

1.907(48 dots)

25.422(640 dots)

0.636(16 dots)

70Hz(70.09)

14.27(449 lines)

0.064(2 lines)

1.907(60 lines)

11.12(350 lines)

1.175(37 lines)

+/-

Y

2

720 x 400

28.321

31.468kHz

31.78(900dots)

3.813(108dots)

1.907(54dots)

25.42(720dots)

0.636(18dots)

70Hz(70.085)

14.27(449 lines)

0.064(2 lines)

1.080(34 lines)

12.71(400 lines)

0.381(13 lines)

-/+

Y

5

640 x 480

31.500

37.861kHz

26.413(832 dots)

1.270(40 dots)

3.810(120 dots)

20.317(640 dots)

1.016(32 dots)

72.809Hz

13.735(520 lines)

0.079(3 lines)

0.528(20 lines)

12.678(480 lines)

0.45(17 lines)

-/-

Y

6

640 x 480

31.501

37.5kHz

26.667 (840 dots)

2.032 ( 54 dots)

3.81 ( 120 dots)

20.317 (640 dots)

0.508 ( 26 dots)

75Hz

13.333 (500 lines )

0.08 ( 3 lines )

0.427 ( 16 lines )

12.8 (480 lines )

0.026 ( 1 lines)

- / -

Y

3

640 x 480

25.175

31.5kHz

31.778(800 dots)

3.813( 96 dots)

1.907( 48 dots)

25.422( 640 dots)

0.636( 16 dots)

60Hz

16.683 (525 lines)

0.064 ( 2 lines)

1.049 ( 33 lines)

15.253 (480 lines)

0.317 ( 10 line )

- / -

Y

7

640x480

36

36kHz

23.111 (832 dots)

1.556 (56 dots)

2.222 ( 80 dots)

17.778 (640 dots)

1.555 (56 dots)

85Hz

11.763 (509 lines )

0.069 ( 3 lines )

0.578 ( 25 lines )

11.093 (480 lines )

0.023 ( 1 lines)

-/-

Y

4

640 x 480

30.24

35 kHz

28.571 (864 dots)

2.116 ( 64 dots)

3.175( 96 dots)

21.164( 640 dots)

2.116( 64 dots)

67Hz

15 (525 lines)

0.086( 3 lines)

1.114( 39 lines)

13.714(480 lines)

0.086( 3 line )

- / -

Y

8

800 x 600

36

35.2kHz

28.444(1024 dots)

2.000 ( 72 dots)

3.556 ( 128 dots)

22.222( 800 dots)

0.666 ( 24 dots)

56Hz

17.778 (625 lines)

0.057

( 2 lines)

0.626

( 22 lines)

17.066 (600 lines)

0.029

( 1 line )

+ / +

Y

2006-06-22


TYPE : 190CW7CS/00

BRAND : PHILIPS

22

2006-06-22

590

8639 000 17256

10

54 190CW7 LCD


MODE NO.

RESOLUTION

Dot clock(MHz) f h

A ( us )

B ( us )

C ( us )

D ( us )

E ( us ) f v

O (ms )

P ( ms )

Q (ms )

R ( ms )

S ( ms )

SYNC. H/V

POLARITY

SEP . SYNC

MODE NO.

RESOLUTION

Dot clock(MHz) f h

A ( us )

B ( us )

C ( us )

D ( us )

E ( us ) f v

O (ms )

P ( ms )

Q (ms )

R ( ms )

S ( ms )

SYNC. H/V

POLARITY

SEP . SYNC

13

832 x 624

57.28

49.7kHz

20.11(1152 dots)

1.117(64 dots)

3.91(224 dots)

14.52(832 dots)

0.563(32 dots)

75Hz

13.41(667 lines)

0.06(3 lines)

0.784(39 lines)

12.55(624 lines)

0.016(1 lines)

+/+

Y

9

800 x 600

40

37.9kHz

26.4 (1056 dots)

3.2 ( 128 dots)

2.2 ( 88 dots)

20 ( 800 dots)

1 ( 40 dots)

60Hz

16.579 (628 lines)

0.106 ( 4 lines)

0.607 ( 23 lines)

15.84 (600lines)

0.026 ( 1 line )

+ / +

Y

14

1024 x 768

65

48.363kHz

20.677(1344 dots)

2.092(136 dots)

2.462(160 dots)

15.754(1024 dots)

0.369(24 dots)

60.004Hz

16.666(806 lines)

0.124(6 lines)

0.600(29 lines)

15.880(768 lines)

0.062(3 lines)

- / -

Y

10

800 x 600

50

48.077kHz

20.80 (1040dots)

2.400 ( 120 dots)

1.280 ( 64 dots)

16.00 ( 800 dots)

1.120 ( 56 dots)

72Hz ( 72.188)

13.85 (666 lines)

0.125 ( 6 lines)

0.478 ( 23 lines)

12.48 (600 lines)

0.770 ( 37 line )

+ / +

Y

15

1024 x 768

75

56.5kHz

17.707(1328 dots)

1.813(136 dots)

1.920(144 dots)

13.653(1024 dots)

0.321 (24 dots)

70.004Hz

14.272(806 lines)

0.106(6 lines)

0.514(29 lines)

13.599(768 lines)

0.053(3 lines)

-/-

Y

11

800 x 600

49.498

46.9kHz

21.333 (1056 dots)

1.616 ( 80 dots)

3.232 ( 160 dots)

16.162 ( 800 dots)

0.323 ( 16 dots)

75Hz

13.333 (625 lines)

0.064 ( 3 lines)

0.448 ( 21 lines)

12.8 (600 lines)

0.021 ( 1 line )

+ / +

Y

12

800 x 600

56.251

53.7kHz

18.631 (1048 dots)

1.138 ( 64 dots)

2.702 ( 152 dots)

14.222 ( 800 dots)

0.569 ( 32 dots)

85Hz

11.756(631 lines)

0.056 ( 3 lines)

0.503 ( 27 lines)

11.179 (600 lines)

0.018 ( 1 lines)

+ / +

Y

16

1024 x 768

78.75

60kHz

16.66 (1312dots)

1.219 ( 96 dots)

2.235 ( 176 dots)

13.003 ( 1024 dots)

0.203 ( 16 dots)

75Hz ( 75.000)

13.328 (800 lines)

0.05( 3 lines)

0.446 ( 28 lines)

12.80 (768 lines)

0.017 ( 1 line )

+ / +

Y

MODE NO.

RESOLUTION

Dot clock(MHz) f h

A ( us )

B ( us )

C ( us )

D ( us )

E ( us ) f v

O (ms )

P ( ms )

Q (ms )

R ( ms )

S ( ms )

SYNC. H/V

POLARITY

SEP . SYNC

17

1024 x 768

83.096

61.1kHz

16.367 (1360dots)

1.348 ( 112 dots)

2.022 ( 168 dots)

12.323 ( 1024 dots)

0.674 ( 56 dots)

76Hz

13.142 (803 lines)

0.049 ( 3 lines)

0.507 ( 31 lines)

12.57 (768 lines)

0.016 ( 1 line )

+ / +

Y

18

1024 x 768

94.5

68.7kHz

14.561 (1376 dots)

1.016 ( 96 dots)

2.201 ( 208 dots)

10.836 ( 1024 dots)

0.508 ( 48 dots)

85Hz

11.765 (808 lines)

0.044 ( 3 lines)

0.524 ( 36 lines)

11.183 (768lines)

0.014 ( 1 line )

+ / +

Y

19

1152 x 864

79.9

54.0kHz

18.523(1480 dots)

1.952(156 dots)

1.352(108 dots)

14.418(1152 dots)

0.801(64 dots)

60Hz

16.671(900lines)

0.148(8 lines)

0.445(24 lines)

16.004(864 lines)

0.074(4 lines)

+/+

Y

20

1152 x 864

94.5

63.9kHz

15.661(1480 dots)

1.016(96 dots)

1.116(105 dots)

12.19(1152 dots)

1.339(127 dots)

70Hz

14.283(912lines)

0.047(3lines)

0.689(44 lines)

13.531(864 lines)

0.016(1 lines)

+/+

Y

2006-06-22


TYPE : 190CW7CS/00

BRAND : PHILIPS

22

2006-06-22

590

8639 000 17256

11


55

MODE NO.

RESOLUTION

Dot clock(MHz) f h

A ( us )

B ( us )

C ( us )

D ( us )

E ( us ) f v

O (ms )

P ( ms )

Q (ms )

R ( ms )

S ( ms )

SYNC. H/V

POLARITY

SEP . SYNC

MODE NO.

RESOLUTION

Dot clock(MHz) f h

A ( us )

B ( us )

C ( us )

D ( us )

E ( us ) f v

O (ms )

P ( ms )

Q (ms )

R ( ms )

S ( ms )

SYNC. H/V

POLARITY

SEP . SYNC

MODE NO.

RESOLUTION

Dot clock(MHz)

F h

A ( us )

B ( us )

C ( us )

D ( us )

E ( us )

F v

O (ms )

P ( ms )

Q (ms )

R ( ms )

S ( ms )

SYNC. H/V

POLARITY

SEP . SYNC

21

1152 x 864

108

67.5kHz

14.815 (1600 dots)

1.185 ( 128 dots)

2.37 ( 256 dots)

10.667 ( 1152 dots)

0.593 ( 64 dots)

75Hz

13.333 (900 lines)

0.044 ( 3 lines)

0.474 ( 32 lines)

12.8 (864 lines)

0.015 ( 1 lines)

- / -

Y

25

1280 x 960

108

60kHz

16.667(1800 dots)

1.037(112 dots)

2.889(312 dots)

11.852(1280 dots)

0.889(96 dots)

60Hz

16.667(1000 lines)

0.05(3 lines)

0.600(36 lines)

16(960 lines)

0.017(1 lines)

+/+

Y

29

1280 x 1024

130.223

76kHz

13.158 (1712 dots)

1.024 ( 133 dots)

1.905 ( 248 dots)

9.83 ( 1280 dots)

0.399( 51 dots)

72Hz

14 (1064 lines)

0.02 ( 2 lines)

0.5 ( 38 lines)

13.468 (1024 lines)

0.012 ( 0 line)

+ / +

Y

22

1152 x 870

100

68.7kHz

14.56 (1456 dots)

1.28 ( 128 dots)

1.44( 144 dots)

11.52 ( 1152 dots)

0.32 ( 32 dots)

75Hz

13.333 (916 lines)

0.044 ( 3 lines)

0.568( 39 lines)

12.678 (870 lines)

0.043 ( 4 line )

- / -

Y

26

1280 x 960

129.895

75kHz

13.307 (1728 dots)

1.047 ( 136 dots)

1.725 ( 224 dots)

9.857 ( 1280 dots)

0.678 ( 88 dots)

75Hz

13.333 (1002 lines)

0.039 ( 3 lines)

0.48 ( 36 lines)

12.774 (960 lines)

0.04 ( 3 lines )

+ / +

Y

30

1280 x 1024

135

80kHz

12.504(1688 dots)

1.067(144 dots)

1.837(248 dots)

9.481(1280 dots)

0.119(16 dots)

75Hz

13.329(1066 lines)

0.038(3 lines)

0.475(38 lines)

12.804(1024 lines)

0.012 (1 line)

+/+

Y

23

1152 x 900

94.5

61.8kHz

16.169 (1528 dots)

1.354 ( 128 dots)

2.201 ( 208 dots)

12.19 ( 1152 dots)

0.424 ( 40 dots)

66Hz

15.151 (937lines)

0.065 ( 4 lines)

0.501 ( 31 lines)

14.552 (900lines)

0.033 ( 2 line )

Serr-

Y

24

1152 x 900

108

71.8kHz

13.926 (1054dots)

1.185 ( 128 dots)

1.778 ( 192 dots)

10.667 ( 1152 dots)

0.296 ( 32 dots)

76Hz

13.132 (943 lines)

0.111 ( 8 lines)

0.46 ( 33 lines)

12.533 (900 lines)

0.028 ( 2 lines)

+ / +

Y

27 28

1280 x 1024

108

64kHz

15.63 (1688 dots)

1.037 ( 112 dots)

2.296 ( 248 dots)

11.852 ( 1280 dots)

0.445 ( 48 dots)

60Hz

1280 x 1024

117

71.7kHz

13.949 (1632 dots)

0.957 (112 dots)

1.915 (224 dots)

10.94 (1280 dots)

0.137 (16 dots)

67Hz

16.661 (1066 lines) 14.883 (1067lines)

0.047 ( 3 lines) 0.112 ( 8 lines)

0.594 ( 38 lines) 0.46 ( 33 lines)

16.005 (1024 lines) 14.283 (1024 lines)

0.015 ( 1 line) 0.028 (2 lines )

+ / + + / +

Y Y

31

1280 x 1024

138.008

81.1kHz

12.326 (1664 dots)

0.474 (64 dots)

2.133 (288 dots)

9.481 (1280 dots)

0.238 (32 dots)

76Hz

13.139 (1066 lines)

0.099 ( 8 lines)

0.394 ( 32 lines)

12.622 (1024 lines)

0.024( 2 lines )

- / -

Y

32

1360 x 768

85.5

47.712kHz

20.959(1792 dots)

1.31(112 dots)

2.994(256 dots)

15.906(1360 dots)

0.749(64 dots)

60.015Hz

16.662(795 lines)

0.126(6 lines)

0.377(18 lines)

16.097(768 lines)

0.063(3 lines)

+ / +

Y

2006-06-22


TYPE : 190CW7CS/00

BRAND : PHILIPS

22

2006-06-22

590

8639 000 17256

12

56

190CW7 LCD


MODE NO.

RESOLUTION

Dot clock(MHz)

F h

A ( us )

B ( us )

C ( us )

D ( us )

E ( us )

F v

O (ms )

P ( ms )

Q (ms )

R ( ms )

S ( ms )

SYNC. H/V

POLARITY

SEP . SYNC

MODE NO.

RESOLUTION

Dot clock(MHz)

F h

A ( us )

B ( us )

C ( us )

D ( us )

E ( us )

F v

O (ms )

P ( ms )

Q (ms )

R ( ms )

S ( ms )

SYNC. H/V

POLARITY

SEP . SYNC

33

1440 x 900

106.50

55.935kHz

17.878(1904 dots)

1.427(152 dots)

2.718(232 dots)

13.521(1440 dots)

0.751(80 dots)

59.887Hz

16.698(934 lines)

0.107(6 lines)

0.447(25 lines)

16.09(900 lines)

0.054(3 lines)

- / +

Y

37

1280x720

95.75

56.456KHz

17.713

1.337

2.172

13.368

0.836

74.777

13.373

0.089

0.478

12.753

0.053

-/+

Y

34

1440 x 900

136.75

70.635kHz

14.157(1936 dots)

1.112(152 dots)

1.814(248 dots)

10.53(1440 dots)

0.702(96 dots)

74.984Hz

13.336(942 lines)

0.085(6 lines)

0.467(33 lines)

12.741(900 lines)

0.042(3 lines)

- / +

Y

38

1280 x 768

79.5

47.776kHz

20.931

1.61

2.415

16.101

0.805

59.87Hz

16.703

0.147

0.419

16.075

0.063

- / +

Y

35

1280x720

74.5

44.772KHz

22.335

1.718

2.577

17.181

0.859

59.855

16.707

0.112

0.447

16.082

0.067

-/+

Y

39

1280 x 768

94.976

56kHz

17.857

1.432

2.19

13.477

0.758

70Hz

14.286

0.054

0.5

13.714

0.018

-/+

Y

36

1280x720

89.04

52.5KHz

19.048

1.527

2.336

14.376

0.809

70

14.286

0.057

0.495

13.714

0.019

-/+

Y

40

1280 x 768

102.25

60.289kHz

16.587

1.252

2.034

12.518

0.782

74.893Hz

13.352

0.116

0.448

12.739

0.05

-/ +

Y

2006-06-22


TYPE : 190CW7CS/00

BRAND : PHILIPS

22

2006-06-22

590

8639 000 17256

13


57

3.4

Horizontal scanning

Sync polarity : Positive or Negative

Scanning frequency : 30 - 83 K Hz

3.5

Vertical scanning

Sync polarity : Positive or Negative

Scanning frequency : 5 5 - 7 5 Hz

3.6 Power input connection

Power cord length

Power cord type

: 1.8 M

: 3 leads power cord with protective earth plug.

3.7 Power management

The monitor must comply with the Microsoft On Now specification, with two power management states, as defined by the VESA DPMS document. The monitor must appropriately display the

DPMS state.

Mode

Power-On

HSYNC VSYN

C

On On

Video active

Pwr-cons.

Indication

Green LED

Rec.

time

--

Off

DC Power

Off

Off Off blanked

N/A

< 36 W(typ..)

34 W (typ.)

< 1 W

< 1 W

Amber LED

LED Off

< 3 s

3.8 Display identification

In accordance with VESA Display Channel Standard Ver.1.0 and having DDC 2B capability

4 Visual characteristics

4.4 Test conditions

Unless otherwise specified, this specification is defined under the following conditions.

(1) Input signal : As defined in 3.3, 1440 x 900 non-interlaced mode ( 56K/60Hz ), signal sources must have 75 ohm output impedance.

(2) Luminance setting : controls to be set to 300 nits with full screen 100 % duty cycle white signal

(3) Warm up: more than 30 minutes after power on with signal supplied.

(4) Ambient light : 400 -- 600 lux.

(5) Ambient temperature : 20 ± 5 °C

4.5 Brightness

> 300 nits (at panel color temperature, at center of the screen, set contrast and brightness at maximum. )

2006-06-22


TYPE : 190CW7CS/00

BRAND : PHILIPS

22

2006-06-22

590

8639 000 17256

14

58

190CW7 LCD


4.3

4.4

Image size

Actual display size 410.4 x 256.5mm

Brightness uniformity

Set contrast at 100% and turn the brightness to get average above 300 nits at centre of the screen.

Apply the Fig 1, it should comply with the following formula:

B_min

X 100% >75%

B_max

Where B_max =Maximum brightness

B_min = Minimum brightness

4.5 Check Cross talk (S)

Apply Pattern 2. Set contrast and brightness at 100 %.

Measure YA. Then output Pattern 3 and measure YB.

the cross talk value :

ABS( YA - YB )

¾¾¾¾¾¾¾¾¾ X 100% < 1.5 %

YA

4.6 White color adjustment

There are three factory preset white color 9300K, 6500K, sRGB.

Apply full white pattern, with brightness in 100 % position and the contrast control at 50 % position.

The 1931 CIE Chromaticity (color triangle) diagram (x,y) coordinate for the screen center should be:

Product spec.


± 0.02

Y = 0.297

± 0.02


± 0.02

Y = 0.329

± 0.02


± 0.02

Y = 0.329

± 0.02



± 0.005

Y = 0.297

± 0.005


± 0.005

Y = 0.329

± 0.005


± 0.005

Y = 0.329

± 0.005



± 0.015

Y = 0.297

± 0.015


± 0.015

Y = 0.329

± 0.015

2006-06-22


TYPE : 190CW7CS/00

BRAND : PHILIPS

22

2006-06-22

590

8639 000 17256

15

GENERAL PRODUCT SPECIFICATION(Continued) 190CW7 LCD 59 sRGB CIE coordinates X = 0.313 ± 0.015

Y = 0.329 ± 0.015

5

5.1

Mechanical characteristics

Cosmetic -

5.2

5.3

Mechanical data files -

Philips TPV ID

ProE files required

Location of Philips logo Per Philips make-up sheet

Gap between panel and front bezel < 1.2

mm

Location of Control icons Per Philips Graphic Sheet

Front side:

Rear :

5.4 Color for resin/paint -

5.5 Resins

Per Philips graphic sheet

Per Philips graphic sheet

Per Philips make-up sheet

·

RoHS required

·

WEEE required.

·

Resin type/selection refer to Project Book Section 7.2 Plastic material.

5.6 If paint is used

·

RoHS required

·

WEEE require

5.7 Plastic mold tooling

·

Tooling to be designed to minimize cosmetic defects induced by molding process (sink, blush, weld lines, gate marks, ejector marks, etc.).

·

Painting to cover up cosmetic defects due to molding is strongly discouraged.

5.8 Plastics flammability

·

All Plastics to be Flame Retardant UL 94-V0 or Better (if monitor weighs less than 18kg; UL94-V0 is

OK).

·

All major plastic parts (bezel, back cover ) need to be molded from same resin.

5.9 Texture/Glossing of housing

·

The texture area and texture no should follow Philips make-up sheet TPV Spec .

·

The exterior surfaces shall have a uniform texture.

·

Philips must approve the mold texturing.

·

Detail document for texture refer to UAN-D249.

·

< = 20 gloss units

2006-06-22


TYPE : 190CW7CS/00

BRAND : PHILIPS

22

2006-06-22

590

8639 000 17256

16

60 190CW7 LCD


5.10

·

5.11 Label

Tilt and swivel base

Tilt angle : -5

° max.(forward) and +

20

° min.(backward )

·

Regulatory label / Carton label should follow Philips requirement.

·

Detail document refer to Philips Engineering Reference Book.

5.12 Product dimension / Weight

·

Unit dimension (incl. pedestal) : 438.5

(W) * 358 (H) * 211

·

Packed unit dimension (WW carton) : 520 W* 190 H* 392 Dmm

)

(D) mm

·

Packed unit dimension ( China carton ) :

·

Net weight : 5.0

Kg

·

Gross weight

·

: 6.7

Kg

5.13 Transportation

Transportation standards refer to TYE-M0002

5.13.1Transportation packages

Packaging and wrapping shall be sufficient to protect the product against damage or loss during shipment from the supplier to the destination specified in the purchase order. All packaging materials are subject to test and evaluation per TYE-M0002. The cushion material shall be constructed using EPS material.

5.13.2 Transportation Test

The overall test refer to TYE-M0002.

Vibration, drop test should be performed at ambient temperature(20 o

C to 23 o

C) and relative humidity

(40% to 65% ).

A. Transportation test specification for all regions except China/India

·

Package test

1.

Random Vibration test

2.

Drop test

3.

Cold Drop test (for design reference)

·

Un-package test

1. Half sine shock test (non operation)

B. Transportation test specification for China/India

·

Package test

1. Random Vibration test

2. Drop test

3. Cold Drop test (for design reference)

·

Un-package test

1. Sine vibration (operating)

2. Half sine shock test (non operation)

2006-06-22


TYPE : 190CW7CS/00

BRAND : PHILIPS

22

2006-06-22

590

8639 000 17256

17


61

5.14

Pallet / Container loading

Except China

Transportation standards refer to TYE-M0002.

Pallet Slip sheet

·

Air shipment -

·

Sea container 20'(pallet/slip sheet) 660 ---

---

·

Sea container 40'(pallet/slip sheet) 1386

·

Sea container 40' High Cube (pallet/slip sheet) - 1008

·

Truck shipmenttbc

---

1008

6

A.

Air shipment

B.

Container loading for other regions

C.

Truck loading for other regions

Environmental characteristics

The following sections define the interference and susceptibility condition limits that might occur between external environment and the display device.

6.1 Susceptibility of display to external environment

Operating

Storage

- Temperature : 0 to 40 degree C

- Humidity : 80% max

- Altitude : 0-3658m


- Temperature : -20 to 60 degree C

- Humidity : 95% max

- Altitude : 0-12192m


Note: recommend at 5 to 35°C, Humidity less than 60 %

6.2 Transportation tests

Refer to 5.15.2

6.3 Display disturbances from external environment

According to IEC 801-2 for ESD disturbances

6.4 Display disturbances to external environment

7 Reliability

7.1 Mean Time Between Failures

8

System MTBF (Including the LCD panel and CCFL) : 50,000 hrs

Quality assurance requirements

2006-06-22


TYPE : 190CW7CS/00

BRAND : PHILIPS

22

2006-06-22

590

8639 000 17256

18

62 190CW7 LCD


8.1

Acceptance test

9

According to MIL-STD-105D Control II level

AQL: 0.4 (major)

1.5 (minor)

(Please also refer to annual quality agreement)

Customer acceptance criteria: UAW0377/00



BRIGHT DOT DEFECTS

190CW7

ACCEPTABLE LEVEL

MODEL

1 lit sub-pixel

2 adjacent lit sub-pixels

3 adjacent lit sub-pixels (one white pixel)

Distance between two bright dot defects*

Bright dot defects within 20 mm circle

Total bright dot defects of all type

2 3

0 1

0

25mm or more

15mm

25mm

0

3

BLACK DOT DEFECTS

MODEL

1 dark sub-pixel

2 adjacent dark sub-pixels

3 adjacent dark sub-pixels (one white pixel)

Distance between two black dot defects*

Black dot defects within 20 mm circle*

Total black dot defects of all type

190CW7

4 5

2 1 2

0

15mm or

More

15mm

1

4 5

ACCEPTABLE LEVEL

TOTAL DOT DEFECTS

MODEL

Total bright or black dot defects of all type

* 1 or 2 adjacent sub-pixel defects = 1 dot defect

190CW7

ACCEPTABLE LEVEL

5

2006-06-22


TYPE : 190CW7CS/00

BRAND : PHILIPS

22

2006-06-22

590

8639 000 17256

19


63

Fig 1: Brightness Uniformity

320 640 960

PIXEL

P2

P7

P6

P1

P3

P8

P4 P9 P5

Fig 2: Cross talk pattern

Gray level 46 (64 Gray level)

1/6

768

256

512

1/2

YA

1/2

2006-06-22


TYPE : 190CW7CS/00

BRAND : PHILIPS

22

2006-06-22

590

8639 000 17256

20

64 190CW7 LCD


1/3

Fig 3: Cross talk Pattern

Center at Gray level 0 (Black)

1/3

1/6

1/3

1/2

1/3

YB

1/2

1/3

2006-06-22


TYPE : 190CW7CS/00

BRAND : PHILIPS

22

2006-06-22

590

8639 000 17256

21

GENERAL PRODUCT SPECIFICATION(Continued) 190CW7 LCD 65

SEPARATE SYNC.

C

VIDEO

D

E

HORIZONTAL

B

Q

A

VIDEO

R

S

VERTICAL

P

O

COMPOSITE SYNC.

C

VIDEO

D

E

HORIZONTAL

B

A

FIG-4 TIMING CHART -1

2006-06-22


TYPE : 190CW7CS/00

BRAND : PHILIPS

22

2006-06-22

590

8639 000 17256

22

66

190CW7 LCD

Type: 190CW7CS/00

Exploded View

Repair Tips

190CW7 LCD

67

0. Warning

All ICs and many other semi-conductors are susceptible to electrostatic discharges (ESD). Careless handling during repair can reduce life drastically. When repairing, make sure that you are connected with the same potential as the mass of the unit via a wrist wrap with resistance. Keep components and tools also at the same potential !

1. Servicing of SMDs (Surface Mounted Devices)

1.1 General cautions on handling and storage

- Oxidation on the terminals of SMDs results in poor soldering.

Do not handle SMDs with bare hands.

- Avoid using storage places that are sensitive to oxidation such as places with sulphur or chlorine gas, direct sunlight, high temperatures or a high degree of humidity. The capacitance or resistance value of the SMDs may be affected by this.

- Rough handling of circuit boards containing SMDs may cause damage to the components as well as the circuit boards. Circuit boards containing SMDs should never be bent or flexed. Different circuit board materials expand and contract at different rates when heated or cooled and the components and/or solder connections may be damaged due to the stress. Never rub or scrape chip components as this may cause the value of the component to change.

Similarly, do not slide the circuit board across any surface.

preferably be equipped with a thermal control (soldering temperature: 225 to 250 C).

- The chip, once removed, must never be reused.

1.4 Attachment of SMDs

- Locate the SMD on the solder lands by means of tweezers and solder the component on one side. Ensure that the component is positioned correctly on the solder lands (see Fig.2A).

- Next complete the soldering of the terminals of the component (see Fiq. 2B).

1.2 Removal of SMDs

- Heat the solder (for 2-3 seconds) at each terminal of the chip. By means of litz wire and a slight horizontal force, small components can be removed with the soldering iron.

They can also be removed with a solder sucker (see Fig.

1A)

While holding the SMD with a pair of tweezers, take it off gently using the soldering iron's heat applied to each terminal (see Fig. 1 B).

- Remove the excess solder on the solder lands by means of litz wire or a solder sucker (see Fig. 1C).

1.3 Caution on removal

- When handling the soldering.iron. use suitable pressure and be careful.

- When removing the chip, do not use undue force with the pair of tweezers.

- The soldering iron to be used (approx. 30 W) should

2. Caution when attaching SMDs

- When soldering the SMD terminals, do not touch them directly with the soldering iron. The soldering should be done as quickly as possible, care must be taken to avoid damage to the terminals of the SMDs themselves.

- Keep the SMD's body in contact with the printed board when soldering.

- The soldering iron to be used (approx. 30 W ) should preferably be equipped with a thermal control (soldering temperature: 225 to 250 C).

- Soldering should not be done outside the solder land.

- Soldering flux (of rosin) may be used, but should not be acidic.

- After soldering, let the SMD cool down gradually at room temperature.

- The quantity of solder must be proportional to the size of the solder land. If the quantity is too great, the SMD might crack or the solder lands might be torn loose from the printed board (see Fig. 3).

Right

Fig.3 Examples

68

190CW7 LCD

Repair Tips

3. Lead-free product identification

You can identify lead-free product by Philips-lead-free logo on PCB.

4. Lead-free product repair instruction

4.1 Use only lead-free Solder Alloy 0622 149 00106(1.2mm SAC305) or 0622 14900108(1.0mm SAC305).

Remark: For lead free soldering material, please visit www.alphametals.com

website for details. This is recommended by Philips.

4.2 Use only adequate solder tools applicable for lead-free soldering-tin. The solder tool must be able to reach at least a solder-temperature of 400 , to stabilize the adjusted temperature at the solder-tip and to exchange solder-tips for different applications.

Small Passives/Actives to be removed with thermal tweezers

Automated system for IC and BGA repair (Microscope, Camera, Beam split optics, Computer, Programmer, Heat controllers, Vacuum system, Laser pointer) Solder Hand-Tool (Adjustable in temperature height, Temperature shall be held constant,Flexible tips)

4.3 Adjust your solder tool so that a temperature around 360 -380 is reached and stabilized at the solder joint.

Heating-time of the solder-joint should not exceed ~ 4 sec. Avoid temperatures above 400 otherwise wear-out of tips will rise drastically and flux-fluid will be destroyed.Corrosion of Tool-Spikes can be avoided when using SAC305 and a temperature of less than 400 .

4.4 Mix of lead-free solder-tin/parts with leaded soldering-tin/parts is possible but not recommended. If not to avoid clean carefully the solder-joint from old tin and re-solder with new tin.

4.5 Use only original spare-parts listed in the Service-Manuals. Standard-material(consumables) can also be purchased at external companies.

4.6 Special information for lead-free BGA-ICs: this ICs will be delivered in so-called dry-packaging to protect the IC against moisture and with lead-free logo on it. This packaging may only be opened shortly before it is used (soldered). Otherwise the body of the IC gets wet inside and during the heating time the structure of the IC will be destroyed due to high (steam-)pressure. If the packaging was opened before usage the IC has to be heated up for some hours (around 90 ) for drying (Take attention for ESD-protection!)

5. Rework on BGA (Ball Grid Array) ICs

General

Although (LF)BGA assembly yields are very high, there may still be a requirement for component rework. By rework, we mean the process of removing the component from the PWB and replacing it with a new component. If an (LF)BGA is removed from a PWB, the solder balls of the component are deformed drastically so the removed (LF)BGA has to be discarded.

Device Removal

As is the case with any component that, it is essential when removing an (LF)BGA, the board, tracks, solder lands, or surrounding components are not damaged. To remove an (LF)BGA, the board must be uniformly heated to a temperature close to the reflow soldering temperature. A uniform temperature reduces the chance of warping the PWB.

To do this, we recommend that the board is heated until it is certain that all the joints are molten. Then carefully pull the component off the board with a vacuum nozzle. For the appropriate temperature profiles, see the IC data sheet.

Area Preparation

When the component has been removed, the vacant IC area must be cleaned before replacing the (LF)BGA.

Removing an IC often leaves varying amounts of solder on the mounting lands. This excessive solder can be removed with either a solder sucker or solder wick. The remaining flux can be removed with a brush and cleaning agent. After the board is properly cleaned and inspected, apply flux on the solder lands and on the connection balls of the(LF)BGA

Note: Do not apply solder paste, as this has shown to result in problems during re-soldering.

Device Replacement

The last step in the repair process is to solder the new component on the board. Ideally, the (LF)BGA should be aligned under a microscope or magnifying glass. If this is not possible, try to align the (LF)BGA with any board markers.

To reflow the solder, apply a temperature profile according to the IC data sheet. So as not to damage neighbouring components, it may be necessary to reduce some temperatures and times.

More Information

For more information on how to handle BGA devices, visit this URL: http://www.atyourservice.ce.philips.com (needs subscription). After login, select Magazine , then go to Workshop Information . Here you will find Information on how

.to deal with BGA-ICs.

Repair Flow Chart

AC IN

Power Board

Control Board

Scaler Board

LCD Panel

No power

(power indicator off)

Bad Scaler Board

NG

Check 18V/12V/5V

OK

Check Scaler Board

NG

Bad power board

OK

Check Control Board

OK

Check Control Wires

Check LCD Panel

190CW7 LCD

69

70

190CW7 LCD

Repair Flow Chart

Power Board

OK

NG

Bad Power Board

OK

OK

Check Scaler Board

OK

Bad Scaler Board

OK

Repair Flow Chart

190CW7 LCD

71

18V/12V/5V DC

OK

NO

OK

Check

Power Board

OK

Check LCD Panel

Control Board

OK

OK

Board

72

190CW7 LCD

Safety Test Requirements

All units that are returned for service or repair must pass the original manufactures safety tests. Safety testing requires both

Hipot and Ground Continuity testing.

HI-POT TEST INSTRUCTION

1.Application requirements

1.1 All mains operated products must pass the Hi-Pot test as described in this instruction.

1.2 This test must be performed again after the covers have been refitted following the repair, inspection or modification of the product.

2. Test method

2.1 Connecting conditions

2.1.1 The test specified must be applied between the parallelblade plug of the mainscord and all accessible metal parts of the product.

2.1.2 Before carrying out the test, reliable conductive connections must be ensured and thereafter be maintained throughout the test period.

2.1.3 The mains switch(es) must be in the "ON" position.

2.2 Test Requirements

All products should be HiPot and Ground Continuity tested as follows:

Condition HiPot Test for HiPot Test for products where products where the mains input the mains input is range is Full range(or 220V

AC)

110V AC(USA type)

Test 2820VDC voltage (2000VAC)

1700VDC

(1200VAC)

Ground Continuity

Test requirement

Test time 3 seconds

(min.)

Trip current

(Tester)

Ramp time

(Tester) set at 100 uA for Max.

limitation; set at 0.1 uA for

Min. Limitation set at 2 seconds

1 second

5 mA

Test current:

25A,AC

Test time:

3 seconds(min.)

Resistance required:

<=0.09+Rohm,

R is the resistance of the mains cord.

3. Equipments and Connection

3.1. Equipments

For example :

- ChenHwa 9032 PROGRAMMABLE AUTO SAFETY

TESTER

- ChenHwa 510B Digital Grounding Continuity Tester

- ChenHwa 901 (AC Hi-pot test), 902 (AC, DC Hi-pot test)

Withstanding Tester

3.2. Connection

* Turn on the power switch of monitor before Hipot and

Ground Continuity testing.

Clip

(ChenHwa 9032 tester)

Video cable

Connect the "video cable" or "grounding screw" to the CLIP on your tester.

Clip

Grounding screw

2.2.1 The minimum test duration for Quality Control Inspector must be 1 minute.

2.2.2 The test voltage must be maintained within the specified voltage + 5%.

2.2.3 There must be no breakdown during the test.

2.2.4 The grounding blade or pin of mains plug must be conducted with accessible metal parts.

Connect the power cord to the monitor.

4. Recording

Power outlet

(Rear view of monitor)

Hipot and Ground Continuity testing records have to be kept for a period of 10 years.

Recommended Parts List

Recommended Parts List

TYPE:190CW7CS/00(CMO)

Item Philips 12NC DESCRIPTION

9965 000 39710 BASE

9965 000 39714 POWER LENS

9965 000 39715 FRONT BEZEL PHILIPS

9965 000 39716 KEY BUTTON

9965 000 39717 REAR COVER

9965 000 39718 STAND TOP

9965 000 39719 STAND BOTTOM

9965 000 39720 HINGE

IC801 9965 000 36059 0Z9938

IC901 9965 000 39747 LD7575PS SOP-8

IC902 9965 000 36055 PC123Y22FZOF

IC903 9965 000 36054 KIA431A-AT/P TO-92

U401 9965 000 41346 MCU ASSY

U403 9965 000 41345 EEPROM ASSY

U404 9965 000 35965 M24C02-WMN6TP

U405 9965 000 35965 M24C02-WMN6TP

U701 9965 000 37095 AIC1084-33PM

U702 9965 000 35963 AI1117D-1.8-EI

TPV 18NC

034G1844VB1B

A33G00601C

A34G0112VOA2T

A33G0067VO1T

A34G0051VB1T

A34G0053VB1B

A34G0054VB1B

A37G00071

056G60810

056G37961

056G1393A

056G15812

705GP9K056005

705GP9K056006

056G113334

056G113334

056G5637

056G56331

190CW7 LCD

73

74

190CW7 LCD

Spare Parts List

Model: 190CW7CS/00(CMO) 12NC: 8639 000 17256


Mechanical Parts

9965 000 39710 BASE

9965 000 39714 POWER LENS

9965 000 39715 FRONT BEZEL PHILIPS

9965 000 39716 KEY BUTTON

9965 000 39717 REAR COVER

9965 000 39718 STAND TOP

9965 000 39719 STAND BOTTOM

9965 000 39720 HINGE

Accessory

9965 000 35910 POWER CORD miscellanea

9965 000 39709 RUBBER

9965 000 39711 SIGNAL CABLE

9965 000 39712 FFC CABLE 30P 205MM P1.0

LCD Panel

9965 000 39713 PANEL LCD 19" A1-L02 CMO

PCB Assy

9965 000 39721 CONVERSION BOARD

9965 000 39722 KEY BOARD

9965 000 39723 POWER BOARD ASSY

PCB Assy

9965 000 39721 CONVERSION BOARD

Various

CN202 9965 000 39725 DVID CONN 24P FEMALE 90 DVR024

CN405 9965 000 35960 D-SUB 15PIN

CN406 9965 000 36924 FPC CONN. 1.0MM 30P

C401 9965 000 36917 CHIP 1000PF 50V NPO

C402 9965 000 36917 CHIP 1000PF 50V NPO

C403 9965 000 36921 CHIP 0.047UF 50V X7R

C404 9965 000 36921 CHIP 0.047UF 50V X7R

C405 9965 000 36921 CHIP 0.047UF 50V X7R

C406 9965 000 36921 CHIP 0.047UF 50V X7R

C407 9965 000 36921 CHIP 0.047UF 50V X7R

C408 9965 000 36921 CHIP 0.047UF 50V X7R

C409 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

C410 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

C411 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

C412 9965 000 37324 CAP:CER 0.22UF-20%-80% 10V SM

C413 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

C414 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

C416 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

C417 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

C418 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

C419 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

C420 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

C421 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

C422 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

C423 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

C424 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

C425 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

C426 9965 000 36922 KY16VB470M-L 10*12.5

C427 9965 000 36919 CER1 0603 NP0 50V 22P PM5 R

C428 9965 000 36919 CER1 0603 NP0 50V 22P PM5 R

C429 9965 000 36916 CHIP 10PF -0.5PF 50V NPO

C430 9965 000 36919 CER1 0603 NP0 50V 22P PM5 R

C431 9965 000 36923 KY25VB47-M-CC3.0 5*11MM

C432 9965 000 35959 LOW ESR EC 4.7 UF 50V NCC

C436 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

C437 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

C438 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

C439 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

C440 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

C441 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

C442 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

C443 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

C444 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

C445 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

C446 9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

TPV 18NC

034G1844VB1B

A33G00601C

A34G0112VOA2T

A33G0067VO1T

A34G0051VB1T

A34G0053VB1B

A34G0054VB1B

A37G00071

089G404A18NLS

012G62161

089G728GAA901

089G179E30C7

750GLM90A1211N

CBPC6MNNPHA

KEPC6AP1

PWPC942MR1P

CBPC6MNNPHA

088G35424FHGP

088G35315FH

033G801930FH

065G060310231

065G060310231

065G060347332

065G060347332

065G060347332

065G060347332

065G060347332

065G060347332

065G060310412

065G060310412

065G060310412

065G060322417

065G060310412

065G060310412

065G060310412

065G060310412

065G060310412

065G060310412

065G060310412

065G060310412

065G060310412

065G060310412

065G060310412

065G060310412

067G215L4713N

065G060322031

065G060322031

065G060310031

065G060322031

067G215V4704N

067G215Y4797N

065G060310412

065G060310412

065G060310412

065G060310412

065G060310412

065G060310412

065G060310412

065G060310412

065G060310412

065G060310412

065G060310412

C467

C468

C469

C470

C701

C702

C703

C704

C705

C706

C707

C708

C709

C710

C711

C712

C457

C458

C459

C460

C461

C462

C463

C464

C465

C466

C447

C448

C449

C450

C454

C455

C456

9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

9965 000 38992 CHIP 1UF 16V X7R 0603

9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

9965 000 36917 CHIP 1000PF 50V NPO

9965 000 36917 CHIP 1000PF 50V NPO

9965 000 36917 CHIP 1000PF 50V NPO

9965 000 36917 CHIP 1000PF 50V NPO

9965 000 36917 CHIP 1000PF 50V NPO

9965 000 36917 CHIP 1000PF 50V NPO

9965 000 36917 CHIP 1000PF 50V NPO

9965 000 36917 CHIP 1000PF 50V NPO

9965 000 36917 CHIP 1000PF 50V NPO

9965 000 36917 CHIP 1000PF 50V NPO

9965 000 36917 CHIP 1000PF 50V NPO

9965 000 36917 CHIP 1000PF 50V NPO

9965 000 36917 CHIP 1000PF 50V NPO

9965 000 36917 CHIP 1000PF 50V NPO

9965 000 37517 1000PF -10% 50V X7R

9965 000 37517 1000PF -10% 50V X7R

9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

9965 000 36918 CER2 0603 X7R 16V 100N PM10 R

9965 000 35958 KY25VB100M-L 6.3*11

9965 000 35958 KY25VB100M-L 6.3*11

9965 000 35958 KY25VB100M-L 6.3*11

9965 000 35958 KY25VB100M-L 6.3*11

9965 000 35958 KY25VB100M-L 6.3*11

9965 000 35958 KY25VB100M-L 6.3*11

R432

R433

R434

R435

R436

R437

R438

R440

R441

R442

R419

R420

R421

R422

R423

R424

R426

R427

R428

R431

R408

R410

R411

R414

R415

R416

R417

R418

R401

R402

R403

R404

R405

R406

R407

R454

R455

R456

R457

R458

R459

R460

R443

R444

R445

R446

R447

R450

R451

R452

R453

9965 000 35971 CHIPR 10K OHM -5% 1/16W

9965 000 35971 CHIPR 10K OHM -5% 1/16W

9965 000 35972 RST SM 0603 RC0603 100K PM5 R

9965 000 35972 RST SM 0603 RC0603 100K PM5 R

9965 000 35969 CHIPR 100 OHM -5% 1/16W

9965 000 35969 CHIPR 100 OHM -5% 1/16W

9965 000 35969 CHIPR 100 OHM -5% 1/16W

9965 000 35969 CHIPR 100 OHM -5% 1/16W

9965 000 36002 RST SM 0603 JUMP MAX 0R05 R

9965 000 36002 RST SM 0603 JUMP MAX 0R05 R

9965 000 35972 RST SM 0603 RC0603 100K PM5 R

9965 000 35971 CHIPR 10K OHM -5% 1/16W

9965 000 36002 RST SM 0603 JUMP MAX 0R05 R

9965 000 35971 CHIPR 10K OHM -5% 1/16W

9965 000 35971 CHIPR 10K OHM -5% 1/16W

9965 000 35971 CHIPR 10K OHM -5% 1/16W

9965 000 35970 CHIPR 1K OHM -5% 1/16W

9965 000 35974 CHIPR 150 OHM -5% 1/16W

9965 000 35970 CHIPR 1K OHM -5% 1/16W

9965 000 35974 CHIPR 150 OHM -5% 1/16W

9965 000 35974 CHIPR 150 OHM -5% 1/16W

9965 000 35970 CHIPR 1K OHM -5% 1/16W

9965 000 35970 CHIPR 1K OHM -5% 1/16W

9965 000 35970 CHIPR 1K OHM -5% 1/16W

9965 000 35970 CHIPR 1K OHM -5% 1/16W

9965 000 35970 CHIPR 1K OHM -5% 1/16W

9965 000 35970 CHIPR 1K OHM -5% 1/16W

9965 000 35973 RST SM 0603 RC0603 1M PM5 R

9965 000 35977 CHIPR 2.2K OHM -5% 1/16W

9965 000 35977 CHIPR 2.2K OHM -5% 1/16W

9965 000 35969 CHIPR 100 OHM -5% 1/16W

9965 000 35969 CHIPR 100 OHM -5% 1/16W

9965 000 35969 CHIPR 100 OHM -5% 1/16W

9965 000 35969 CHIPR 100 OHM -5% 1/16W

9965 000 35978 CHIP 3.3K OHM 1/10W

9965 000 35978 CHIP 3.3K OHM 1/10W

9965 000 36068 CHIP 150OHM 1/4W

9965 000 37788 CHIP 390 OHM 1/10W

9965 000 35971 CHIPR 10K OHM -5% 1/16W

9965 000 35981 CHIPR 4.7K OHM -5% 1/16W

9965 000 36002 RST SM 0603 JUMP MAX 0R05 R

9965 000 35969 CHIPR 100 OHM -5% 1/16W

9965 000 35969 CHIPR 100 OHM -5% 1/16W

9965 000 35969 CHIPR 100 OHM -5% 1/16W

9965 000 35982 CHIPR 75 OHM -5% 1/16W

9965 000 35982 CHIPR 75 OHM -5% 1/16W

9965 000 35982 CHIPR 75 OHM -5% 1/16W

9965 000 36002 RST SM 0603 JUMP MAX 0R05 R

9965 000 35971 CHIPR 10K OHM -5% 1/16W

9965 000 35971 CHIPR 10K OHM -5% 1/16W

9965 000 35981 CHIPR 4.7K OHM -5% 1/16W

061L0603103

061L0603102

061L0603151

061L0603102

061L0603151

061L0603151

061L0603102

061L0603102

061L0603102

061L0603102

061L0603102

061L0603102

061L0603105

061L0603222

061L0603222

061L0603101

061L0603101

061L0603101

061L0603101

061L0603332

061L0603103

061L0603103

061L0603104

061L0603104

061L0603101

061L0603101

061L0603101

061L0603101

061L0603000

061L0603000

061L0603104

061L0603103

061L0603000

061L0603103

061L0603103

061L0603332

061L1206151

061L0603391

061L0603103

061L0603472

061L0603000

061L0603101

061L0603101

061L0603101

061L0603750

061L0603750

061L0603750

061L0603000

061L0603103

061L0603103

061L0603472

065G060310412

065G060310412

065G060310412

065G060310512

065G060310412

065G060310412

065G060310231

065G060310231

065G060310231

065G060310231

065G060310231

065G060310231

065G060310231

065G060310231

065G060310231

065G060310231

065G060310231

065G060310231

065G060310231

065G060310231

065G060310232

065G060310232

065G060310412

065G060310412

065G060310412

065G060310412

065G060310412

067G215L1014N

067G215L1014N

067G215L1014N

067G215L1014N

067G215L1014N

067G215L1014N

Spare Parts List

R481

R484

R486

R487

R488

R489

R490

R491

R496

R497

R499

R701

R469

R470

R471

R472

R473

R476

R478

R479

R480

R461

R462

R463

R464

R465

R466

R467

R468

9965 000 36002 RST SM 0603 JUMP MAX 0R05 R

9965 000 36002 RST SM 0603 JUMP MAX 0R05 R

9965 000 36002 RST SM 0603 JUMP MAX 0R05 R

9965 000 36002 RST SM 0603 JUMP MAX 0R05 R

9965 000 36002 RST SM 0603 JUMP MAX 0R05 R

9965 000 36002 RST SM 0603 JUMP MAX 0R05 R

9965 000 36002 RST SM 0603 JUMP MAX 0R05 R

9965 000 36002 RST SM 0603 JUMP MAX 0R05 R

9965 000 35971 CHIPR 10K OHM -5% 1/16W

9965 000 35970 CHIPR 1K OHM -5% 1/16W

9965 000 37788 CHIP 390 OHM 1/10W

9965 000 35971 CHIPR 10K OHM -5% 1/16W

9965 000 36068 CHIP 150OHM 1/4W

9965 000 35971 CHIPR 10K OHM -5% 1/16W

9965 000 35981 CHIPR 4.7K OHM -5% 1/16W

9965 000 35981 CHIPR 4.7K OHM -5% 1/16W

9965 000 35981 CHIPR 4.7K OHM -5% 1/16W

9965 000 35981 CHIPR 4.7K OHM -5% 1/16W

9965 000 36003 RST SM 0603 RC0603 47K PM5 R

9965 000 36002 RST SM 0603 JUMP MAX 0R05 R

9965 000 36002 RST SM 0603 JUMP MAX 0R05 R

9965 000 35969 CHIPR 100 OHM -5% 1/16W

9965 000 35969 CHIPR 100 OHM -5% 1/16W

9965 000 36002 RST SM 0603 JUMP MAX 0R05 R

9965 000 36002 RST SM 0603 JUMP MAX 0R05 R

9965 000 35970 CHIPR 1K OHM -5% 1/16W

9965 000 35970 CHIPR 1K OHM -5% 1/16W

9965 000 36002 RST SM 0603 JUMP MAX 0R05 R

9965 000 35980 CHIPR 47 OHM -5% 1/16W

FB401 9965 000 36934

FB402 9965 000 36002 RST SM 0603 JUMP MAX 0R05 R

FB403 9965 000 36934

FB404 9965 000 36934



FB407 9965 000 37332 B201209D102TT

FB408 9965 000 35993 CHIP BEAD

FB410 9965 000 35993 CHIP BEAD

FB411 9965 000 35993 CHIP BEAD

FB412 9965 000 35993 CHIP BEAD

FB413 9965 000 35993 CHIP BEAD

FB414 9965 000 35993 CHIP BEAD

FB415 9965 000 36933 CHIP BEAD 120 OHM 0603FBM-11-1






FB701 9965 000 35993 CHIP BEAD

071G59B300K

061L0603000

071G59B300K

071G59B300K

061L0603000

061L0603000

071G56D102

071G56K121

071G56K121

071G56K121

071G56K121

071G56K121

071G56K121

071G59B121K

071G59B121K

071G59B121K

071G59B121K

071G59B121K

071G59B121K

071G56K121

FB702 9965 000 35993 CHIP BEAD

FB703 9965 000 35993 CHIP BEAD

FB704 9965 000 35993 CHIP BEAD

FB707 9965 000 35993 CHIP BEAD

X401

071G56K121

071G56K121

071G56K121

071G56K121

9965 000 35961 CRYSTAL 12MHZ HC-49US ARG6-120 093G2251

D404

D405

D406

D407

D408

D409

D410

D411

D412

D413

D414

D415

D416

D417

D701

D702

9965 000 35994 DIO SIG SM BAV99 (PHSE)R












9965 000 35995 BAV70 SOT-23

9965 000 35995 BAV70 SOT-23

9965 000 36935 FA20-04

9965 000 36935 FA20-04

ZD401 9965 000 35996 UDZS5.6B

ZD402 9965 000 35996 UDZS5.6B

ZD403 9965 000 35996 UDZS5.6B

ZD404 9965 000 35996 UDZS5.6B

ZD405 9965 000 35996 UDZS5.6B

ZD406 9965 000 35996 UDZS5.6B

ZD407 9965 000 35996 UDZS5.6B

ZD408 9965 000 35996 UDZS5.6B

ZD409 9965 000 35996 UDZS5.6B

ZD410 9965 000 35996 UDZS5.6B

ZD411 9965 000 35996 UDZS5.6B

ZD412 9965 000 35996 UDZS5.6B

ZD413 9965 000 35996 UDZS5.6B

093G6433

093G6433

093G6433

093G6433

093G6433

093G6433

093G6433

093G6433

093G6433

093G6433

093G6433

093G6433

093G6442PP

093G6442PP

093G20403F

093G20403F

093G39S34T

093G39S34T

093G39S34T

093G39S34T

093G39S34T

093G39S34T

093G39S34T

093G39S34T

093G39S34T

093G39S34T

093G39S34T

093G39S34T

093G39S34T

061L0603000

061L0603000

061L0603000

061L0603000

061L0603000

061L0603000

061L0603000

061L0603000

061L0603103

061L0603102

061L0603391

061L0603103

061L1206151

061L0603103

061L0603472

061L0603472

061L0603472

061L0603472

061L0603473

061L0603000

061L0603000

061L0603101

061L0603101

061L0603000

061L0603000

061L0603102

061L0603102

061L0603000

061L0603470

190CW7 LCD

75

ZD414 9965 000 35996 UDZS5.6B

Q401

Q402

Q404

Q405

Q406

U401

U403

U404

U405

U701

U702

9965 000 35966 PMBS3904/PHILIPS-SMT(04)

9965 000 12957 TR PNP PMBS3906 SOT23(PHILIPS)

9965 000 12957 TR PNP PMBS3906 SOT23(PHILIPS)

9965 000 35968 A03401 SOT23 BY AOS(A1)

9965 000 35966 PMBS3904/PHILIPS-SMT(04)

9965 000 41346 MCU ASSY

9965 000 41345 EEPROM ASSY

9965 000 35965 M24C02-WMN6TP

9965 000 35965 M24C02-WMN6TP

9965 000 37095 AIC1084-33PM

9965 000 35963 AI1117D-1.8-EI

093G39S34T

057G4174

057G4176

057G4176

057G7631

057G4174

705GP9K056005

705GP9K056006

056G113334

056G113334

056G5637

056G56331

PCB Assy

2490 9965 000 39722 KEY BOARD

Various

CN101 9965 000 39726 PIN HEADER 2*6 R/A

SW1 9965 000 36000 TACT SWITCH TSPB-2 -NP

SW2 9965 000 36000 TACT SWITCH TSPB-2 -NP

SW3

SW4

SW5

9965 000 36000 TACT SWITCH TSPB-2 -NP



C101

C102

C103

C104

C105

9965 000 36004 0.01UF -10% 50V X7R

9965 000 36004 0.01UF -10% 50V X7R

9965 000 36004 0.01UF -10% 50V X7R

9965 000 36004 0.01UF -10% 50V X7R

9965 000 36004 0.01UF -10% 50V X7R

R105

R106

R107

R108

R109

9965 000 35970 CHIPR 1K OHM -5% 1/16W

9965 000 35971 CHIPR 10K OHM -5% 1/16W

9965 000 35970 CHIPR 1K OHM -5% 1/16W

9965 000 35971 CHIPR 10K OHM -5% 1/16W

9965 000 35969 CHIPR 100 OHM -5% 1/16W

D101 9965 000 39727 LED GP32032C-R03-ZY-HB

C811

C811

C812

C813

C814

C815

C815

C801

C804

C805

C806

C807

C809

C810

C816

C818

C819

C820

C822

C823

C824

C825

C826

C827

C828

C829

C831

C834

C835

PCB Assy

2670 9965 000 39723 POWER BOARD ASSY

Various

F901

F901

9965 000 39741

9965 000 36046

FUSE 3.15A 250V MET3.15

1.5MM RIVET

NR901 9965 000 36046 1.5MM RIVET

PT801 9965 000 36093 X'FMR DARFONTK.2006M.101

PT801 9965 000 38142 TRANSFORMER ASS'Y

PT801 9965 000 36046 1.5MM RIVET

PT802 9965 000 36093 X'FMR DARFONTK.2006M.101

PT802 9965 000 38142 TRANSFORMER ASS'Y

PT802 9965 000 36046 1.5MM RIVET

Q903 9965 000 36046 1.5MM RIVET

T901

T901

T901

9965 000 39739

9965 000 39740

9965 000 36046

XFMR FOR POWER LITAI

XFMR FOR POWER LISHIN

1.5MM RIVET

9965 000 36041

9965 000 36073

9965 000 36044

9965 000 39773

9965 000 36045

9965 000 39773

9965 000 36941

9965 000 36941

9965 000 36941

CHIP 0.1U 50V X7R

9965 000 36073 CHIP 1UF 25V X7R 0805

9965 000 36991 1000PF 50V NPO

CHIP 1UF 25V X7R 0805

9965 000 39768 10NF/50V/0805/X7R

9965 000 39770 CHIP 0.022UF 50V X7R 0805

CHIP 470PF 50V NPO

9965 000 36007 ED 470UF 25V

9965 000 39732 470UF 25V

CHIP 1000PF 500V X7R

9965 000 39773 CHIP 1000PF 500V X7R

9965 000 39771 CHIP CAP 0.22 UF 25V X7R

9965 000 36007 ED 470UF 25V

9965 000 39732 470UF 25V

9965 000 39729 22PF 5% SL 3KV TDK

9965 000 39772 3200PF/25V/X7R

CHIP 0.047UF 50V X7R

9965 000 36044 CHIP 470PF 50V NPO

9965 000 39773 CHIP 1000PF 500V X7R


5PF 5% SL 3KV

5PF 5% SL 3KV

5PF 5% SL 3KV

9965 000 39772 3200PF/25V/X7R

9965 000 36041 CHIP 0.1U 50V X7R

9965 000 36041 CHIP 0.1U 50V X7R

9965 000 36044 CHIP 470PF 50V NPO

9965 000 39729 22PF 5% SL 3KV TDK

9965 000 36941 5PF 5% SL 3KV

KEPC6AP1

033G802712H

077G6001GCJ

077G6001GCJ

077G6001GCJ

077G6001GCJ

077G6001GCJ

065G060310332

065G060310332

065G060310332

065G060310332

065G060310332

061L0603102

061L0603103

061L0603102

061L0603103

061L0603101

081G121GGP

PWPC942MR1P

084G557

006G31502

006G31502

080GL19T8DN1

S80GL19T8V1

006G31502

080GL19T8DN1

S80GL19T8V1

006G31502

006G31502

080GL17T37LGP

080GL17T37LSGP

006G31502

065G080510432

065G080510522

065G080510231

065G080510522

065G080510332

065G080522332

065G080547131

067G215D4714K

067G215L4714H

065G120610272

065G120610272

065G080522422

067G215D4714K

067G215L4714H

065G3J2206ET

065G080533232

065G080547332

065G080547131

065G120610272

065G120610272

065G3J5096ET

065G3J5096ET

065G3J5096ET

065G080533232

065G080510432

065G080510432

065G080547131

065G3J2206ET

065G3J5096ET

76

190CW7 LCD

Spare Parts List

C911

C912

C912

C916

C917

C918

C919

C904

C905

C905

C905

C906

C907

C908

C909

C910

C911

C930

C931

C932

C933

C934

C935

C935

C936

C936

C937

C937

C844

C845

C846

C847

C848

C900

C901

C902

C903

C904

C837

C838

C839

C840

C841

C842

C843

9965 000 39729 22PF 5% SL 3KV TDK

9965 000 36041 CHIP 0.1U 50V X7R

9965 000 36041 CHIP 0.1U 50V X7R

9965 000 36073 CHIP 1UF 25V X7R 0805

9965 000 39729 22PF 5% SL 3KV TDK

9965 000 36041 CHIP 0.1U 50V X7R

9965 000 36041 CHIP 0.1U 50V X7R

9965 000 36041 CHIP 0.1U 50V X7R

9965 000 36991 1000PF 50V NPO

9965 000 36991 1000PF 50V NPO

9965 000 36991 1000PF 50V NPO

9965 000 36991 1000PF 50V NPO

9965 000 39731 2200PF -20% 250VAC

9965 000 39730 Y1.CAP.001UF 250VAC MURATA

9965 000 39730 Y1.CAP.001UF 250VAC MURATA

9965 000 37794 FILM CAPACITOR

9965 000 36007 ED 470UF 25V

9965 000 39732 470UF 25V

9965 000 36051 100UF 450V 18*36 105 BY HERMEI

9965 000 36086 100UF 450V

9965 000 36046 1.5MM RIVET

9965 000 39781 KY50VB10M-TP5 5*11.5

9965 000 39781 KY50VB10M-TP5 5*11.5

9965 000 39774 CHIP 0.1UF 25V X7R 1206

9965 000 39769 220PF 50V NPO

9965 000 36044 CHIP 470PF 50V NPO

9965 000 36007 ED 470UF 25V

9965 000 39732 470UF 25V

9965 000 36007 ED 470UF 25V

9965 000 39732 470UF 25V

9965 000 36041 CHIP 0.1U 50V X7R

9965 000 36041 CHIP 0.1U 50V X7R

9965 000 36041 CHIP 0.1U 50V X7R

9965 000 36041 CHIP 0.1U 50V X7R

9965 000 39780 CERAMIC CAP

9965 000 39780 CERAMIC CAP

9965 000 39780 CERAMIC CAP

9965 000 39780 CERAMIC CAP

9965 000 39780 CERAMIC CAP

9965 000 36007 ED 470UF 25V

9965 000 39732 470UF 25V

9965 000 36007 ED 470UF 25V

9965 000 39732 470UF 25V

9965 000 36007 ED 470UF 25V

9965 000 39732 470UF 25V

R816

R817

R818

R819

R822

R823

R824

R825

R805

R806

R807

R808

R810

R812

R813

R814

R815

R826

R827

R828

R829

C808

F902

F903

9965 000 39752 180K OHM 1/8W

9965 000 39751 0 OHM 1/8W

9965 000 39751 0 OHM 1/8W

JR801 9965 000 35984 CHIPR 0OHM -5% 1/10W

JR803 9965 000 36067 CHIPR 0 OHM -5% 1/8W

JR804 9965 000 35984 CHIPR 0OHM -5% 1/10W

JR805 9965 000 35984 CHIPR 0OHM -5% 1/10W

JR806 9965 000 36067 CHIPR 0 OHM -5% 1/8W

JR807 9965 000 35984 CHIPR 0OHM -5% 1/10W

JR808 9965 000 36067 CHIPR 0 OHM -5% 1/8W

JR809 9965 000 36067 CHIPR 0 OHM -5% 1/8W

JR901 9965 000 36067 CHIPR 0 OHM -5% 1/8W

JR902 9965 000 36067 CHIPR 0 OHM -5% 1/8W

NR901 9965 000 39728 8 OHM NCT

R801 9965 000 39749 100K 0805

R802

R803

R804

9965 000 36063

9965 000 36964

9965 000 36964

300K OM 1/8W

CHIPR 10K OHM -5% 1/10W


9965 000 36070

9965 000 36964

9965 000 39764

9965 000 39756

9965 000 36013

9965 000 39757

9965 000 36981

9965 000 39763

9965 000 39763

CHIPR 470 OHM -5% 1/8W


CHIP 22OHM 5% 8W


CHIP 1M OHM 5% 1/8W

9965 000 36964 CHIPR 10K OHM -5% 1/10W

9965 000 36013 CHIP 1M OHM 5% 1/8W

9965 000 39760 CHIPR 750K OHM -5% 1/8W

9965 000 36965 CHIPR 100K OHM -5% 1/10W

9965 000 36013 CHIP 1M OHM 5% 1/8W

9965 000 39754 SMD 39KOHM/0805/ -5% 1/8W

9965 000 39763 CHIP 15 OHM 5% 1206 1/4W

9965 000 39763 CHIP 15 OHM 5% 1206 1/4W

9965 000 36083 MGFR 6.2MOHM -5% 1/2W

9965 000 39761 CHIP 82KOHM 1/8W

9965 000 39759 750 OHM

9965 000 39758 CHIP 51KOHM 1/8W

CHIP 510 OHM 1% 1/8W

CHIP 7.5K OHM 1/10W

CHIP 15 OHM 5% 1206 1/4W

CHIP 15 OHM 5% 1206 1/4W

061L0805184

061G1206000

061G1206000

061L0805000

061L1206000

061L0805000

061L0805000

061L1206000

061L0805000

061L1206000

061L1206000

061L1206000

061L1206000

061G58080WT

061G0805104

061L0805304

061L0805103

061L0805103

061L1206471

061L0805103

061L1206220

061L0805473

061L0805105

061L0805103

061L0805105

061L0805754

061L0805104

061L0805105

061L0805393

061L1206150

061L1206150

061G212Y625KT

061L0805823

061L0805751

061L0805513

061L08055100F

061L0805752

061L1206150

061L1206150

065G3J2206ET

065G080510432

065G080510432

065G080510522

065G3J2206ET

065G080510432

065G080510432

065G080510432

065G080510231

065G080510231

065G080510231

065G080510231

065G306M2222BM

065G306M1022BM

065G306M1022BM

063G10747410S

067G215D4714K

067G215L4714H

067G215S10115H

067G215S10115K

006G31502

067G2151007NT

067G2151007NT

065G120610432

065G080522131

065G080547131

067G215D4714K

067G215L4714H

067G215D4714K

067G215L4714H

065G080510432

065G080510432

065G080510432

065G080510432

065G2K1521TGP

065G2K1521TGP

065G2K1521TGP

065G2K1521TGP

065G2K1521TGP

067G215D4714K

067G215L4714H

067G215D4714K

067G215L4714H

067G215D4714K

067G215L4714H

R911

R912

R913

R914

R916

R919

R920

R921

R922

R923

R858

R860

R901

R902

R903

R904

R905

R906

R909

R910

R830

R831

R832

R836

R837

R841

R842

R843

R846

R847

R848

R849

R850

R851

R852

R853

R924

R925

R926

R927

R931

R934

R935

R936

R937

R938

9965 000 39761 CHIP 82KOHM 1/8W

9965 000 36981 CHIP 7.5K OHM 1/10W

9965 000 36083 MGFR 6.2MOHM -5% 1/2W

9965 000 36963 CHIPR 1K OHM -5% 1/10W

9965 000 39767 CHIPR 5.1OHM -5% 1/4W

9965 000 39750 RST CHIPR 560 OHM -1% 1/8W

9965 000 39767 CHIPR 5.1OHM -5% 1/4W

9965 000 36963 CHIPR 1K OHM -5% 1/10W

9965 000 36013 CHIP 1M OHM 5% 1/8W

9965 000 36013 CHIP 1M OHM 5% 1/8W

9965 000 36013 CHIP 1M OHM 5% 1/8W

9965 000 36013 CHIP 1M OHM 5% 1/8W

9965 000 39755 CHIRP 4.7K OHM -5% 1/10W

9965 000 36986 CHIP 4.7KOHM 5% 1/4W

9965 000 39755 CHIRP 4.7K OHM -5% 1/10W

9965 000 39755 CHIRP 4.7K OHM -5% 1/10W

9965 000 39759 750 OHM

9965 000 36013 CHIP 1M OHM 5% 1/8W

9965 000 36024 CHIPR 680K OHM -5% 1/8W

9965 000 36024 CHIPR 680K OHM -5% 1/8W

9965 000 36024 CHIPR 680K OHM -5% 1/8W

9965 000 39766 RST CHIPR 3.9KOHM -5% 1/4W

9965 000 36010 100K OHM 5% 2W

9965 000 36022 CHIP 100 OHM 5% 1/8W

9965 000 39765 CHIP 3.3OHM 1/4W

9965 000 39764 CHIP 22OHM 5% 8W

9965 000 39762 CHIP 1K OHM 5% 1/8W

9965 000 36964 CHIPR 10K OHM -5% 1/10W

9965 000 36965 CHIPR 100K OHM -5% 1/10W

9965 000 39744 RST MOFR 0.47OHM -5% 2WS

9965 000 36022 CHIP 100 OHM 5% 1/8W

9965 000 36070 CHIPR 470 OHM -5% 1/8W

9965 000 36963 CHIPR 1K OHM -5% 1/10W

9965 000 36963 CHIPR 1K OHM -5% 1/10W

9965 000 36963 CHIPR 1K OHM -5% 1/10W

9965 000 36975 CHIP 33KOHM 1/8W 1%

9965 000 36142 CHIPR 2.4KOHM -1% 1/8W

9965 000 39753 CHIP 3.6KOHM 1/8W 1%

9965 000 36971 CHIP 2KOHM 1/8W

9965 000 36016 CHIP 10KOHM 5% 1/4W

9965 000 39766 RST CHIPR 3.9KOHM -5% 1/4W

9965 000 36022 CHIP 100 OHM 5% 1/8W

9965 000 36022 CHIP 100 OHM 5% 1/8W

9965 000 36022 CHIP 100 OHM 5% 1/8W

9965 000 36022 CHIP 100 OHM 5% 1/8W

9965 000 39766 RST CHIPR 3.9KOHM -5% 1/4W

L902

L902

L903

L903

L904

L904

FB901 9965 000 39733 FERRITE BEAD

L901

L901

9965 000 39737

9965 000 39738

CHOKE

CHOKE BY LISHIN

L901

L902

L902

9965 000 36046

9965 000 36088

9965 000 36025

1.5MM RIVET

LINE FILTER

LINE FILTER BY LISHIN

9965 000 39227

9965 000 36046

9965 000 39734

9965 000 39736

9965 000 39734

9965 000 39735

TRANSFORMERS

1.5MM RIVET

CHOKE

CHOKE BY LI SHIN

CHOKE

CHOKE BY LI SHIN

D810

D811

D812

D813

D901

D902

D903

D904

D908

D908

BD901 9965 000 39742 BRIDGE DIODE KBP208G LITEON

D801 9965 000 35994 DIO SIG SM BAV99 (PHSE)R

D802 9965 000 35994 DIO SIG SM BAV99 (PHSE)R

D803

D804

D805

D806

D809

9965 000 35994

9965 000 35994

9965 000 35994

9965 000 35994

9965 000 39779

DIO SIG SM BAV99 (PHSE)R




IN4148W

9965 000 39779

9965 000 39779

9965 000 39779

9965 000 39779

9965 000 36030

IN4148W

IN4148W

IN4148W

IN4148W

RECTIFIER DIODE FR107

9965 000 36095 FR103

9965 000 39775 LL4148-GS08

9965 000 39775 LL4148-GS08

9965 000 39745 SP20150

9965 000 39746 DIODE SP20150R ITO-220 SECOS

D909

D909

9965 000 39745 SP20150

9965 000 39746 DIODE SP20150R ITO-220 SECOS

ZD801 9965 000 36079 RLZ 5.6B LLDS

ZD901 9965 000 39777 RLZ 13B LLDS

ZD902 9965 000 36079 RLZ 5.6B LLDS

ZD903 9965 000 36080 PTZ 9.1B

ZD904 9965 000 39778 RLZ18B LLDS

071G5529GP

073L17453LGGP

073L17453LSGGP

006G31502

073G17465H

073G17465LS

S73G17465VW

006G31502

073G25391T

073G25391LSGP

073G25391T

073G25391LS

093G5046028

093G6433

093G6433

093G6433

093G6433

093G6433

093G6433

093G64S511SEM

093G64S511SEM

093G64S511SEM

093G64S511SEM

093G64S511SEM

093G6026T52T

093G6038T52T

093G6432V

093G6432V

093G60252

093G60281

093G60252

093G60281

093G39S24T

093G39S40T

093G39S24T

093G39S38T

093G39S44T

061L0805823

061L0805752

061G212Y625KT

061L0805102

061L1206519

061G08055600F

061L1206519

061L0805102

061L0805105

061L0805105

061L0805105

061L0805105

061L0805472

061L1206472

061L0805472

061L0805472

061L0805751

061L0805105

061L1206684

061L1206684

061L1206684

061L1206392

061G152M10458F

061L1206101

061L1206339

061L1206220

061L1206102

061L0805103

061L0805104

061G152M47858F

061L1206101

061L1206471

061L0805102

061L0805102

061L0805102

061L08053302F

061L08052401F

061L08053601F

061L0805202

061L1206103

061L1206392

061L1206101

061L1206101

061L1206101

061L1206101

061L1206392

ZD905 9965 000 39776 RLZ20B LLDS

Q805

Q806

Q806

Q807

Q808

Q809

Q810

Q903

IC801 9965 000 36059 0Z9938

IC901 9965 000 39747 LD7575PS SOP-8

IC902 9965 000 36055 PC123Y22FZOF

IC903 9965 000 36054 KIA431A-AT/P TO-92

Q801

Q802

Q803

Q804

Q805

9965 000 35966

9965 000 35966

9965 000 35966

9965 000 36033

9965 000 39748

PMBS3904/PHILIPS-SMT(04)



RK7002

AO4828L

9965 000 36100

9965 000 39748

9965 000 36100

9965 000 36033

9965 000 36033

9965 000 36033

9965 000 36033

9965 000 39743

AM9945N

AO4828L

AM9945N

RK7002

RK7002

RK7002

RK7002

STP10NK70ZFP

Spare Parts List

093G39S12T

056G60810

056G37961

056G1393A

056G15812

057G4174

057G4174

057G4174

057G7592

057G7636

057G76314

057G7636

057G76314

057G7592

057G7592

057G7592

057G7592

057G66721

190CW7 LCD

77

78

190CW7 LCD

Different Parts List

Diversity of 190CW7CS/27(CMO) compared with 190CW7CS/00(CMO)


8639 000 17262 190CW7CS/27

9965 000 41575 MAINSCORD

9965 000 41537 MAIN FRAME ASSY CMO

9965 000 41572 REAR COVER ASSY

9965 000 41573 FRONT BEZEL ASSY HP CMO

9965 000 41538 MAIN FRAME CMO

TPV 18NC

089G402A18NLS2

705GZ-000036

705GZ-000037

705GZ-000038

A15G00322



8639 000 17257 190CW7CS/69

TPV 18NC

9965 000 41057 POWER CORD 1.8M PY8B1V6CC0A-060 089G410A18NLSB





705GZ-000036

705GZ-000037

705GZ-000038

A15G00322



8639 000 17259 190CW7CS/93

9965 000 41562 MAINSCORD CCEE 10A 1M8 DET BK




9965 000 41712 EPS(L)

9965 000 41713 EPS(R)

9965 000 41714 CARTON (/93)


TPV 18NC

089G414A18NLSC

705GZ-000036

705GZ-000037

705GZ-000038

Q44G90441

Q44G90442

Z44G90018131A

A15G00322

Diversity of 190WV7CS/00(CMO) compared with 190CW7CS/00(CMO)

Item TPV 18NC

10 034G1844VB1B

20

Description

BASE

089G728GAA901 SIGNAL CABLE

30

40

60

90

089G179E30C7

705GZV15002

705GZV34001

705GZV34002

FFC CABLE 30P 205MM P1.0

MAIN FRAME ASSY CMO

REAR COVER ASSY

FRONT BEZEL ASSY

130 750GLM90A1211N PANEL LCD 19" A1-L02 CMO

140 A34G0053VB1B STAND TOP

150 A34G0054VB1B STAND BOTTOM

160 A37G00071 HINGE

240 089G420A18NIS1 MAINS CORD TWN 7A 1M8 BK

260 CBPC6MNNPZSA1 SCALER?ASSEMBLY

2150 KEPC6AP1 KEY BOARD

2320 PWPC942MR1P

50 Z15G00021

100 A33G00601C

POWER BOARD ASSY

MAIN FRAME CMO

POWER LENS

110 A33G0067VO1T KEY BUTTON

120 A34G0112VOA2T FRONT BEZEL PHILIPS

Philips 12NC

9965 000 39710

9965 000 39711

9965 000 39712

9965 000 43701

9965 000 43702

9965 000 43703

9965 000 39713

9965 000 39718

9965 000 39719

9965 000 39720

9965 000 43167

9965 000 43704

9965 000 39722

9965 000 39723

9965 000 43705

9965 000 39714

9965 000 39716

9965 000 39715

280 033G801930FH

290 067G3151014K

300 067G3151014K

310 067G3151014K

320 067G3151014K

330 067G3151014K

340 067G3151014K

350 067G3154704K

360 067G3154797K

370 067G215L1014N

380 067G215L1014N

390 067G215L1014N

400 067G215L1014N

410 067G215L1014N

420 067G215L4713N

KY25VB100M-L 6.3*11

KY25VB100M-L 6.3*11

KY16VB470M-L 10*12.5

430 067G215S4713K EC 470UF 16V

440 067G215V4704N KY25VB47-M-CC3.0 5*11MM

450 067G215Y4797N LOW ESR EC 4.7 UF 50V NCC

460 088G35315FH D-SUB 15PIN

470 093G2251

480 056G5637

490 056G56321

CRYSTAL 12MHZ HC-49US ARG6-120

AIC1084-33PM

AP1084K33LA

500 056G56331

510 056G113324

520 056G113333

530 056G113334

540 057G4174

AI1117D-1.8-EI

AT24C16AN-10SU-2.7

M24C16-MN6TP

M24C02-WMN6TP


550 057G4174

560 057G4176

570 057G4176

580 057G7631

690 061L0603101

800 061L0603102

FPC CONN. 1.0MM 30P 9965 000 36924

EC 100UF 25V EG1E101MNN0511PU 6.

9965 000 43645


9965 000 43645


9965 000 43645


9965 000 43645


9965 000 43645


9965 000 43645

EC 47UF 25V EG1E470MNN0511PU 5*1 9965 000 43647

5*11MM 9965 000 43648

KY25VB100M-L 6.3*11 9965 000 35958

KY25VB100M-L 6.3*11

KY25VB100M-L 6.3*11

9965 000 35958

9965 000 35958


TR PNP PMBS3906 SOT23(PHILIPS)

TR PNP PMBS3906 SOT23(PHILIPS)

A03401 SOT23 BY AOS(A1)

CHIPR 100 OHM -5% 1/16W


9965 000 35958

9965 000 35958

9965 000 36922

9965 000 43646

9965 000 36923

9965 000 35959

9965 000 35960

9965 000 35961

9965 000 37095

9965 000 37330

9965 000 35963

9965 000 35964

9965 000 39724

9965 000 35965

9965 000 35966

9965 000 35966

9965 000 12957

9965 000 12957

9965 000 35968

9965 000 35969

9965 000 35970

1250 065G060310231

1260 065G060310231

1270 065G060310231

1280 065G060310231

1290 065G060310231

1300 065G060310231

1310 065G060310231

1320 065G060310231

1330 065G060310232

1340 065G060310232

1350 065G060310412

1360 065G060310412

1370 065G060310412

1380 065G060310412

1390 065G060310412

1400 065G060310412

1410 065G060310412

1420 065G060310412

1430 065G060310412

1440 065G060310412

1450 065G060310412

1460 065G060310412

1470 065G060310412

1480 065G060310412

1490 065G060310412

1500 065G060310412

1600 065G060310512

1610 065G060322031

1620 065G060322031

1630 065G060322031

1640 065G060322417

1650 065G060347332

1660 065G060347332

1670 065G060347332

1680 065G060347332

1690 065G060347332

810 061L0603102

820 061L0603102

890 061L0603103

900 061L0603103

910 061L0603103

920 061L0603103

930 061L0603103

1000 061L0603104

1010 061L0603104

1020 061L0603104

1030 061L0603105

1040 061L0603151

1050 061L0603151

1060 061L0603151

1070 061L0603222

1080 061L0603222

1090 061L0603332

1100 061L0603332

1110 061L0603391

1120 061L0603470

1130 061L0603472

1140 061L0603472

1150 061L0603472

1160 061L0603472

1170 061L0603473

1180 061L0603750

1190 061L0603750

1200 061L0603750

1210 061L1206151

1220 061L1206151

1230 065G060310031

1240 065G060310231

1700 065G060347332

1710 071G56D102

1720 071G56D102M

1730 071G56K121

1740 071G56K121

1750 071G56K121

1760 071G56K121

1770 071G56K121

1780 071G56K121

1790 071G56K121

1800 071G56K121

1810 071G56K121M

1820 071G56K121M

1830 071G56K121M

1840 071G56K121M

1850 071G56K121M

1860 071G56K121M

1870 071G56K121M

1880 071G56K121M

1890 071G59B300K

1900 071G59B300K

1910 071G59B300K

1920 071G59B300M

1930 071G59B300M

1940 071G59B300M








RST SM 0603 RC0603 100K PM5 R

RST SM 0603 RC0603 100K PM5 R

RST SM 0603 RC0603 100K PM5 R

RST SM 0603 RC0603 1M PM5 R

CHIPR 150 OHM -5% 1/16W

CHIPR 150 OHM -5% 1/16W

CHIPR 150 OHM -5% 1/16W

CHIPR 2.2K OHM -5% 1/16W


CHIP 3.3K OHM 1/10W

CHIP 3.3K OHM 1/10W

CHIP 390 OHM 1/10W






RST SM 0603 RC0603 47K PM5 R




CHIP 150OHM 1/4W

CHIP 150OHM 1/4W

CHIP 10PF -0.5PF 50V NPO

CHIP 1000PF 50V NPO

CHIP 1000PF 50V NPO

CHIP 1000PF 50V NPO

CHIP 1000PF 50V NPO

CHIP 1000PF 50V NPO

CHIP 1000PF 50V NPO

CHIP 1000PF 50V NPO

CHIP 1000PF 50V NPO

CHIP 1000PF 50V NPO

1000PF -10% 50V X7R

1000PF -10% 50V X7R

CER2 0603 X7R 16V 100N PM10 R

CER2 0603 X7R 16V 100N PM10 R

CER2 0603 X7R 16V 100N PM10 R

CER2 0603 X7R 16V 100N PM10 R

CER2 0603 X7R 16V 100N PM10 R

CER2 0603 X7R 16V 100N PM10 R

CER2 0603 X7R 16V 100N PM10 R

CER2 0603 X7R 16V 100N PM10 R

CER2 0603 X7R 16V 100N PM10 R

CER2 0603 X7R 16V 100N PM10 R

CER2 0603 X7R 16V 100N PM10 R

CER2 0603 X7R 16V 100N PM10 R

CER2 0603 X7R 16V 100N PM10 R

CER2 0603 X7R 16V 100N PM10 R

CER2 0603 X7R 16V 100N PM10 R

CER2 0603 X7R 16V 100N PM10 R


CER1 0603 NP0 50V 22P PM5 R

CER1 0603 NP0 50V 22P PM5 R

CER1 0603 NP0 50V 22P PM5 R

CAP:CER 0.22UF-20%-80% 10V SM







B201209D102TT

CHIP HEAD 1000OHM

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD 30 OHM

CHIP BEAD 30 OHM

CHIP BEAD 30 OHM

9965 000 36917

9965 000 36917

9965 000 36917

9965 000 36917

9965 000 36917

9965 000 36917

9965 000 36917

9965 000 36917

9965 000 37517

9965 000 37517

9965 000 36918

9965 000 36918

9965 000 36918

9965 000 36918

9965 000 36918

9965 000 36918

9965 000 36918

9965 000 36918

9965 000 36918

9965 000 36918

9965 000 36918

9965 000 36918

9965 000 36918

9965 000 36918

9965 000 36918

9965 000 36918

9965 000 38992

9965 000 36919

9965 000 36919

9965 000 36919

9965 000 37324

9965 000 36921

9965 000 36921

9965 000 36921

9965 000 36921

9965 000 36921

9965 000 35970

9965 000 35970

9965 000 35971

9965 000 35971

9965 000 35971

9965 000 35971

9965 000 35971

9965 000 35972

9965 000 35972

9965 000 35972

9965 000 35973

9965 000 35974

9965 000 35974

9965 000 35974

9965 000 35977

9965 000 35977

9965 000 35978

9965 000 35978

9965 000 37788

9965 000 35980

9965 000 35981

9965 000 35981

9965 000 35981

9965 000 35981

9965 000 36003

9965 000 35982

9965 000 35982

9965 000 35982

9965 000 36068

9965 000 36068

9965 000 36916

9965 000 36917

9965 000 36921

9965 000 37332

9965 000 43649

9965 000 35993

9965 000 35993

9965 000 35993

9965 000 35993

9965 000 35993

9965 000 35993

9965 000 35993

9965 000 35993

9965 000 36567

9965 000 36567

9965 000 36567

9965 000 36567

9965 000 36567

9965 000 36567

9965 000 36567

9965 000 36567

9965 000 36934

9965 000 36934

9965 000 36934

9965 000 43707

9965 000 43707

9965 000 43707


1950 093G6433

1960 093G6433

1970 093G6433

1980 093G6433

1990 093G6442PP

2000 093G39S34T

2010 093G39S34T

2020 093G39S34T

2030 093G39S34T

2040 093G39S34T

2050 093G39S34T

2060 093G39S34T

2070 093G39S34T

2080 093G39S34T

2090 093G20403F

2100 093G20403F

2110 705GZV56017

2120 056G562117

2840 081G121GGP

2850 077G6001GCJ

2860 077G6001GCJ

2870 077G6001GCJ

2880 077G6001GCJ

2890 077G6001GCJ

2900 061L0603101

2910 061L0603102

2920 061L0603102

2930 061L0603103

2940 061L0603103

2950 065G060310332





BAV70 SOT-23

UDZS5.6B

UDZS5.6B

UDZS5.6B

UDZS5.6B

UDZS5.6B

UDZS5.6B

UDZS5.6B

UDZS5.6B

UDZS5.6B

FA20-04

9965 000 35994

9965 000 35994

9965 000 35994

9965 000 35994

9965 000 35995

9965 000 35996

9965 000 35996

9965 000 35996

9965 000 35996

9965 000 35996

9965 000 35996

9965 000 35996

9965 000 35996

9965 000 35996

9965 000 36935

FA20-04

CPU ASSEMBLY

9965 000 36935

9965 000 43708

IC NT68663MEFG-128 QFP-128L NOVA 9965 000 37779

LED GP32032C-R03-ZY-HB

TACT SWITCH TSPB-2 -NP



9965 000 39727

9965 000 36000

9965 000 36000

9965 000 36000



CHIPR 100 OHM -5% 1/16W





0.01UF -10% 50V X7R

9965 000 36000

9965 000 36000

9965 000 35969

9965 000 35970

9965 000 35970

9965 000 35971

9965 000 35971

9965 000 36004

2960 065G060310332

2970 065G060310332

2980 065G060310332

2990 065G060310332

0.01UF -10% 50V X7R

0.01UF -10% 50V X7R

0.01UF -10% 50V X7R

0.01UF -10% 50V X7R

3010 063G10747410S FILM CAPACITOR

3020 067G215D4714K ED 470UF 25V

3030 067G215D4714K ED 470UF 25V

3040 067G215D4714K ED 470UF 25V

3050 067G215D4714K ED 470UF 25V

3060 067G215D4714K ED 470UF 25V

3070 067G215D4714K ED 470UF 25V

3080 067G215D4714K ED 470UF 25V

3090 067G215D4714K ED 470UF 25V

3100 067G215L4714H

3110 067G215L4714H

470UF 25V

470UF 25V

3120 067G215L4714H

3130 067G215L4714H

3140 067G215L4714H

3150 067G215L4714H

470UF 25V

470UF 25V

470UF 25V

470UF 25V

3160 067G215L4714H

3170 067G215L4714H

470UF 25V

470UF 25V

3180 067G215S10115H 100UF 450V 18*36 105 BY HERMEI

3190 067G215S10115K 100UF 450V

3200 084G557

3210 093G5046028

3220 056G1393A

3230 061G58080WT

3240 065G3J2206EM

3250 065G3J2206EM

3260 065G3J2206ET

FUSE 3.15A 250V MET3.15

BRIDGE DIODE KBP208G LITEON

PC123Y22FZOF

8 OHM NCT

22PF 3KV

22PF 3KV

22PF 5% SL 3KV TDK

9965 000 36004

9965 000 36004

9965 000 36004

9965 000 36004

9965 000 37794

9965 000 36007

9965 000 36007

9965 000 36007

9965 000 36007

9965 000 36007

9965 000 36007

9965 000 36007

9965 000 36007

9965 000 39732

9965 000 39732

9965 000 39732

9965 000 39732

9965 000 39732

9965 000 39732

9965 000 39732

9965 000 39732

9965 000 36051

9965 000 36086

9965 000 39741

9965 000 39742

9965 000 36055

9965 000 39728

9965 000 43644

9965 000 43644

9965 000 39729

3270 065G3J2206ET

3280 065G3J2206ET

3290 065G3J2206ET

3300 065G3J5096ET

22PF 5% SL 3KV TDK

22PF 5% SL 3KV TDK

22PF 5% SL 3KV TDK

5PF 5% SL 3KV

3310 065G3J5096ET

3320 065G3J5096ET

5PF 5% SL 3KV

5PF 5% SL 3KV

3330 065G3J5096ET 5PF 5% SL 3KV

3340 065G306M1022BM Y1.CAP.001UF 250VAC MURATA


3360 065G306M2222BM 2200PF -20% 250VAC

3370 073G17465H

3380 073G17465LS

LINE FILTER


3390 073G25391T

3400 073G25391T

3410 073G25391LS

CHOKE

CHOKE

CHOKE BY LI SHIN

3420 073G25391LSGP CHOKE BY LI SHIN

3430 073L17453LGGP CHOKE

3440 073L17453LSGGP CHOKE BY LISHIN

3450 080GL17T37LGP XFMR FOR POWER LITAI

3460 080GL17T37LSGP XFMR FOR POWER LISHIN

3470 080GL19T8DN1 X'FMR DARFONTK.2006M.101

3480 080GL19T8DN1

3490 057G66721

X'FMR DARFONTK.2006M.101

STP10NK70ZFP

3500 061G152M10458F 100K OHM 5% 2W

3510 061G152M47858F RST MOFR 0.47OHM -5% 2WS

3520 093G60252

3530 093G60281

SP20150

DIODE SP20150R ITO-220 SECOS

3540 093G60252

3550 093G60281

3560 056G37961

SP20150


LD7575PS SOP-8

3570 056G60810

3580 057G4174

3590 057G4174

0Z9938



9965 000 39729

9965 000 39729

9965 000 39729

9965 000 36941

9965 000 36941

9965 000 36941

9965 000 36941

9965 000 39730

9965 000 39730

9965 000 39731

9965 000 36088

9965 000 36025

9965 000 39734

9965 000 39734

9965 000 39735

9965 000 39736

9965 000 39737

9965 000 39738

9965 000 39739

9965 000 39740

9965 000 36093

9965 000 36093

9965 000 39743

9965 000 36010

9965 000 39744

9965 000 39745

9965 000 39746

9965 000 39745

9965 000 39746

9965 000 39747

9965 000 36059

9965 000 35966

9965 000 35966

190CW7 LCD

79

3600 057G4174

3610 057G7592

3620 057G7592

3630 057G7592

3640 057G7592

3650 057G7592

3660 057G7636

3670 057G7636

3680 057G76314

3690 057G76314

3700 061G0805104

3710 061G08055600F

3720 061G1206000

3730 061G1206000

3740 061L0805000

3750 061L0805000

3760 061L0805000

3770 061L0805000

3780 061L0805102

3790 061L0805102

3800 061L0805102

3810 061L0805102

3820 061L0805102

3830 061L0805103

3840 061L0805103

3850 061L0805103

3860 061L0805103

3870 061L0805103

3880 061L0805104

3890 061L0805104

3900 061L0805105

3910 061L0805105

3920 061L0805105

3930 061L0805105

3940 061L0805105

3950 061L0805105

3960 061L0805105

3970 061L0805105

3980 061L0805184

3990 061L0805202

4000 061L08052401F

4010 061L0805304

4020 061L08053302F

4030 061L08053601F

4040 061L0805393

4050 061L0805472

4060 061L0805472

4070 061L0805472

4080 061L0805473

4090 061L08055100F

4100 061L0805513

4110 061L0805751

4120 061L0805751

4130 061L0805752


RK7002

RK7002

RK7002

RK7002

RK7002

AO4828L

AO4828L

AM9945N

AM9945N

100K 0805

RST CHIPR 560 OHM -1% 1/8W

0 OHM 1/8W

0 OHM 1/8W

CHIPR 0OHM -5% 1/10W
















CHIP 1M OHM 5% 1/8W

CHIP 1M OHM 5% 1/8W

CHIP 1M OHM 5% 1/8W

CHIP 1M OHM 5% 1/8W

CHIP 1M OHM 5% 1/8W

CHIP 1M OHM 5% 1/8W

CHIP 1M OHM 5% 1/8W

CHIP 1M OHM 5% 1/8W

180K OHM 1/8W

CHIP 2KOHM 1/8W

CHIPR 2.4KOHM -1% 1/8W

300K OM 1/8W

CHIP 33KOHM 1/8W 1%

CHIP 3.6KOHM 1/8W 1%

SMD 39KOHM/0805/ -5% 1/8W

CHIRP 4.7K OHM -5% 1/10W





CHIP 51KOHM 1/8W

750 OHM

750 OHM

CHIP 7.5K OHM 1/10W

4140 061L0805752

4150 061L0805754

4160 061L0805823

4170 061L0805823

4180 061L1206000

4190 061L1206000

4200 061L1206000

4210 061L1206000

4220 061L1206000

4230 061L1206000

4240 061L1206101

4250 061L1206101

4260 061L1206101

4270 061L1206101

4280 061L1206101

4290 061L1206101

4300 061L1206102

4310 061L1206103

4320 061L1206150

4330 061L1206150

4340 061L1206150

4350 061L1206150

4360 061L1206220

4370 061L1206220

4380 061L1206339

4390 061L1206392

4400 061L1206392

CHIP 7.5K OHM 1/10W


CHIP 82KOHM 1/8W

CHIP 82KOHM 1/8W













CHIP 1K OHM 5% 1/8W

CHIP 10KOHM 5% 1/4W

CHIP 15 OHM 5% 1206 1/4W

CHIP 15 OHM 5% 1206 1/4W

CHIP 15 OHM 5% 1206 1/4W

CHIP 15 OHM 5% 1206 1/4W

CHIP 22OHM 5% 8W

CHIP 22OHM 5% 8W

CHIP 3.3OHM 1/4W

RST CHIPR 3.9KOHM -5% 1/4W


4410 061L1206392

4420 061L1206471

4430 061L1206471

4440 061L1206472

4450 061L1206519

4460 061L1206519

4470 061L1206684

4480 061L1206684




CHIP 4.7KOHM 5% 1/4W

CHIPR 5.1OHM -5% 1/4W




4490 061L1206684 CHIPR 680K OHM -5% 1/8W

4500 065G2K1521TGP CERAMIC CAP





9965 000 36981

9965 000 39760

9965 000 39761

9965 000 39761

9965 000 36067

9965 000 36067

9965 000 36067

9965 000 36067

9965 000 36067

9965 000 36067

9965 000 36022

9965 000 36022

9965 000 36022

9965 000 36022

9965 000 36022

9965 000 36022

9965 000 39762

9965 000 36016

9965 000 39763

9965 000 39763

9965 000 39763

9965 000 39763

9965 000 39764

9965 000 39764

9965 000 39765

9965 000 39766

9965 000 39766

9965 000 39766

9965 000 36070

9965 000 36070

9965 000 36986

9965 000 39767

9965 000 39767

9965 000 36024

9965 000 36024

9965 000 36024

9965 000 39780

9965 000 39780

9965 000 39780

9965 000 39780

9965 000 39780

9965 000 36963

9965 000 36964

9965 000 36964

9965 000 36964

9965 000 36964

9965 000 36964

9965 000 36965

9965 000 36965

9965 000 36013

9965 000 36013

9965 000 36013

9965 000 36013

9965 000 36013

9965 000 36013

9965 000 36013

9965 000 36013

9965 000 39752

9965 000 36971

9965 000 36142

9965 000 36063

9965 000 36975

9965 000 39753

9965 000 39754

9965 000 39755

9965 000 39755

9965 000 39755

9965 000 39756

9965 000 39757

9965 000 39758

9965 000 39759

9965 000 39759

9965 000 36981

9965 000 35966

9965 000 36033

9965 000 36033

9965 000 36033

9965 000 36033

9965 000 36033

9965 000 39748

9965 000 39748

9965 000 36100

9965 000 36100

9965 000 39749

9965 000 39750

9965 000 39751

9965 000 39751

9965 000 35984

9965 000 35984

9965 000 35984

9965 000 35984

9965 000 36963

9965 000 36963

9965 000 36963

9965 000 36963

80

190CW7 LCD


Diversity of 190CW7CB/69(CMO) compared with 190CW7CS/00(CMO)

Item TPV 18NC

10 089G728GAA901

Description

SIGNAL CABLE

Philips 12NC

9965 000 39711

20

30

40

60

089G179E30C7 FFC CABLE 30P 205MM P1.0

9965 000 39712

089G410A18NLSB POWER CORD 1.8M PY8B1V6CC0A-060 9965 000 41057

705GZ-000036

705GZV34003

110 705GZV34004

MAIN FRAME ASSY CMO

FRONT BEZEL ASSY

REAR COVER ASSY

9965 000 41537

9965 000 43715

9965 000 43716


210 Z34G0022WV1B STAND TOP

220 Z34G0023WV1B

230 A37G00071

240 Z34G0024WV1B

STAND BOTTOM

HINGE

BASE

250 CBPC6MNNPHSB4 CONVERSATION BOARD

2830 KEPC6AP1 KEY BOARD

3000 PWPC942MR1P POWER BOARD ASSY

9965 000 39713

9965 000 43718

9965 000 43719

9965 000 39720

9965 000 43717

9965 000 43523

9965 000 39722

9965 000 39723

90

60

A34G0051VB1T

A15G00322

REAR COVER

MAIN FRAME CMO

90 Z33G0019WV1T KEY BUTTON

100 Z34G0020WVA2T FRONT BEZEL PHILIPS

1 705GZ9K056001 CPU ASSY

2840 081G121GGP

2850 077G6001GCJ

2860 077G6001GCJ

2870 077G6001GCJ

2880 077G6001GCJ






2890 077G6001GCJ

2900 061L0603101

2910 061L0603102

2920 061L0603102

2930 061L0603103

2940 061L0603103

2950 065G060310332

2960 065G060310332


CHIPR 100 OHM -5% 1/16W





0.01UF -10% 50V X7R

0.01UF -10% 50V X7R

9965 000 39717

9965 000 41538

9965 000 43720

9965 000 43721

9965 000 43518

9965 000 39727

9965 000 36000

9965 000 36000

9965 000 36000

9965 000 36000

9965 000 36000

9965 000 35969

9965 000 35970

9965 000 35970

9965 000 35971

9965 000 35971

9965 000 36004

9965 000 36004

2970 065G060310332

2980 065G060310332

2990 065G060310332

3010 063G10747410S

3020 067G215D4714K

3030 067G215D4714K

3040 067G215D4714K

3050 067G215D4714K

3060 067G215D4714K

3070 067G215D4714K

3080 067G215D4714K

3090 067G215D4714K

3100 067G215L4714H

3110 067G215L4714H

3120 067G215L4714H

3130 067G215L4714H

3140 067G215L4714H

3150 067G215L4714H

0.01UF -10% 50V X7R

0.01UF -10% 50V X7R

0.01UF -10% 50V X7R

FILM CAPACITOR

ED 470UF 25V

ED 470UF 25V

ED 470UF 25V

ED 470UF 25V

ED 470UF 25V

ED 470UF 25V

ED 470UF 25V

ED 470UF 25V

470UF 25V

470UF 25V

470UF 25V

470UF 25V

470UF 25V

470UF 25V

3160 067G215L4714H

3170 067G215L4714H

470UF 25V

470UF 25V

3180 067G215S10115H 100UF 450V 18*36 105 BY HERMEI

3190 067G215S10115K 100UF 450V

3200 084G557 FUSE 3.15A 250V MET3.15

3210 093G5046028

3220 056G1393A

3230 061G58080WT


PC123Y22FZOF

8 OHM NCT

3240 065G3J2206EM

3250 065G3J2206EM

3260 065G3J2206ET

3270 065G3J2206ET

3280 065G3J2206ET

3290 065G3J2206ET

3300 065G3J5096ET

3310 065G3J5096ET

3320 065G3J5096ET

3330 065G3J5096ET

22PF 3KV

22PF 3KV

22PF 5% SL 3KV TDK

22PF 5% SL 3KV TDK

22PF 5% SL 3KV TDK

22PF 5% SL 3KV TDK

5PF 5% SL 3KV

5PF 5% SL 3KV

5PF 5% SL 3KV

5PF 5% SL 3KV



3360 065G306M2222BM 2200PF -20% 250VAC

3370 073G17465H

3380 073G17465LS

3390 073G25391T

3400 073G25391T

3410 073G25391LS

LINE FILTER


CHOKE

CHOKE

CHOKE BY LI SHIN






3470 080GL19T8DN1

3480 080GL19T8DN1



3490 057G66721 STP10NK70ZFP

3500 061G152M10458F 100K OHM 5% 2W


3520 093G60252

3530 093G60281

3540 093G60252

SP20150


SP20150

9965 000 39730

9965 000 39730

9965 000 39731

9965 000 36088

9965 000 36025

9965 000 39734

9965 000 39734

9965 000 39735

9965 000 39736

9965 000 39737

9965 000 39738

9965 000 39739

9965 000 39740

9965 000 36093

9965 000 36093

9965 000 39743

9965 000 36010

9965 000 39744

9965 000 39745

9965 000 39746

9965 000 39745

9965 000 36004

9965 000 36004

9965 000 36004

9965 000 37794

9965 000 36007

9965 000 36007

9965 000 36007

9965 000 36007

9965 000 36007

9965 000 36007

9965 000 36007

9965 000 36007

9965 000 39732

9965 000 39732

9965 000 39732

9965 000 39732

9965 000 39732

9965 000 39732

9965 000 39732

9965 000 39732

9965 000 36051

9965 000 36086

9965 000 39741

9965 000 39742

9965 000 36055

9965 000 39728

9965 000 43644

9965 000 43644

9965 000 39729

9965 000 39729

9965 000 39729

9965 000 39729

9965 000 36941

9965 000 36941

9965 000 36941

9965 000 36941


LD7575PS SOP-8

0Z9938




RK7002

RK7002

RK7002

RK7002

RK7002

AO4828L

AO4828L

AM9945N

AM9945N

100K 0805


0 OHM 1/8W

0 OHM 1/8W

















CHIP 1M OHM 5% 1/8W

CHIP 1M OHM 5% 1/8W

CHIP 1M OHM 5% 1/8W

CHIP 1M OHM 5% 1/8W

CHIP 1M OHM 5% 1/8W

CHIP 1M OHM 5% 1/8W

CHIP 1M OHM 5% 1/8W

CHIP 1M OHM 5% 1/8W

180K OHM 1/8W

CHIP 2KOHM 1/8W


300K OM 1/8W

CHIP 33KOHM 1/8W 1%


SMD 39KOHM/0805/ -5% 1/8W






CHIP 51KOHM 1/8W

750 OHM

750 OHM

CHIP 7.5K OHM 1/10W

CHIP 7.5K OHM 1/10W


CHIP 82KOHM 1/8W

CHIP 82KOHM 1/8W













CHIP 1K OHM 5% 1/8W

CHIP 10KOHM 5% 1/4W

CHIP 15 OHM 5% 1206 1/4W

CHIP 15 OHM 5% 1206 1/4W

CHIP 15 OHM 5% 1206 1/4W

CHIP 15 OHM 5% 1206 1/4W

CHIP 22OHM 5% 8W

CHIP 22OHM 5% 8W

CHIP 3.3OHM 1/4W










4110 061L0805751

4120 061L0805751

4130 061L0805752

4140 061L0805752

4150 061L0805754

4160 061L0805823

4170 061L0805823

4180 061L1206000

4190 061L1206000

4200 061L1206000

4210 061L1206000

4220 061L1206000

4230 061L1206000

4240 061L1206101

4250 061L1206101

4260 061L1206101

4270 061L1206101

4280 061L1206101

4290 061L1206101

4300 061L1206102

4310 061L1206103

4320 061L1206150

4330 061L1206150

4340 061L1206150

4350 061L1206150

4360 061L1206220

4370 061L1206220

4380 061L1206339

4390 061L1206392

4400 061L1206392

4410 061L1206392

4420 061L1206471

4430 061L1206471

4440 061L1206472

4450 061L1206519

4460 061L1206519

4470 061L1206684

3550 093G60281

3560 056G37961

3570 056G60810

3580 057G4174

3590 057G4174

3600 057G4174

3610 057G7592

3620 057G7592

3630 057G7592

3640 057G7592

3650 057G7592

3660 057G7636

3670 057G7636

3680 057G76314

3690 057G76314

3700 061G0805104

3710 061G08055600F

3720 061G1206000

3730 061G1206000

3740 061L0805000

3750 061L0805000

3760 061L0805000

3770 061L0805000

3780 061L0805102

3790 061L0805102

3800 061L0805102

3810 061L0805102

3820 061L0805102

3830 061L0805103

3840 061L0805103

3850 061L0805103

3860 061L0805103

3870 061L0805103

3880 061L0805104

3890 061L0805104

3900 061L0805105

3910 061L0805105

3920 061L0805105

3930 061L0805105

3940 061L0805105

3950 061L0805105

3960 061L0805105

3970 061L0805105

3980 061L0805184

3990 061L0805202

4000 061L08052401F

4010 061L0805304

4020 061L08053302F

4030 061L08053601F

4040 061L0805393

4050 061L0805472

4060 061L0805472

4070 061L0805472

4080 061L0805473

4090 061L08055100F

4100 061L0805513

9965 000 39759

9965 000 39759

9965 000 36981

9965 000 36981

9965 000 39760

9965 000 39761

9965 000 39761

9965 000 36067

9965 000 36067

9965 000 36067

9965 000 36067

9965 000 36067

9965 000 36067

9965 000 36022

9965 000 36022

9965 000 36022

9965 000 36022

9965 000 36022

9965 000 36022

9965 000 39762

9965 000 36016

9965 000 39763

9965 000 39763

9965 000 39763

9965 000 39763

9965 000 39764

9965 000 39764

9965 000 39765

9965 000 39766

9965 000 39766

9965 000 39766

9965 000 36070

9965 000 36070

9965 000 36986

9965 000 39767

9965 000 39767

9965 000 36024

9965 000 36964

9965 000 36964

9965 000 36964

9965 000 36964

9965 000 36964

9965 000 36965

9965 000 36965

9965 000 36013

9965 000 36013

9965 000 36013

9965 000 36013

9965 000 36013

9965 000 36013

9965 000 36013

9965 000 36013

9965 000 39752

9965 000 36971

9965 000 36142

9965 000 36063

9965 000 36975

9965 000 39753

9965 000 39754

9965 000 39755

9965 000 39755

9965 000 39755

9965 000 39756

9965 000 39757

9965 000 39758

9965 000 39746

9965 000 39747

9965 000 36059

9965 000 35966

9965 000 35966

9965 000 35966

9965 000 36033

9965 000 36033

9965 000 36033

9965 000 36033

9965 000 36033

9965 000 39748

9965 000 39748

9965 000 36100

9965 000 36100

9965 000 39749

9965 000 39750

9965 000 39751

9965 000 39751

9965 000 35984

9965 000 35984

9965 000 35984

9965 000 35984

9965 000 36963

9965 000 36963

9965 000 36963

9965 000 36963

9965 000 36963


190CW7 LCD

81

4480 061L1206684

4490 061L1206684








4550 065G080510231 1000PF 50V NPO

4560 065G080510231 1000PF 50V NPO

4570 065G080510231

4580 065G080510231

4590 065G080510231

4600 065G080510332

4610 065G080510432

4620 065G080510432

4630 065G080510432

4640 065G080510432

4650 065G080510432

4660 065G080510432

4670 065G080510432

4680 065G080510432

4690 065G080510432

4700 065G080510432

4710 065G080510432

1000PF 50V NPO

1000PF 50V NPO

1000PF 50V NPO

10NF/50V/0805/X7R

CHIP 0.1U 50V X7R

CHIP 0.1U 50V X7R

CHIP 0.1U 50V X7R

CHIP 0.1U 50V X7R

CHIP 0.1U 50V X7R

CHIP 0.1U 50V X7R

CHIP 0.1U 50V X7R

CHIP 0.1U 50V X7R

CHIP 0.1U 50V X7R

CHIP 0.1U 50V X7R

CHIP 0.1U 50V X7R

4720 065G080510432

4730 065G080510522

4740 065G080510522

4750 065G080510522

4760 065G080522131

4770 065G080522332

4780 065G080522422

4790 065G080533232

4800 065G080533232

4810 065G080547131

4820 065G080547131

4830 065G080547131

4840 065G080547131

CHIP 0.1U 50V X7R




220PF 50V NPO

CHIP 0.022UF 50V X7R 0805

CHIP CAP 0.22 UF 25V X7R

3200PF/25V/X7R

3200PF/25V/X7R

CHIP 470PF 50V NPO

CHIP 470PF 50V NPO

CHIP 470PF 50V NPO

CHIP 470PF 50V NPO

9965 000 36041

9965 000 36073

9965 000 36073

9965 000 36073

9965 000 39769

9965 000 39770

9965 000 39771

9965 000 39772

9965 000 39772

9965 000 36044

9965 000 36044

9965 000 36044

9965 000 36044

4850 065G080547332

4860 065G120610272

4870 065G120610272

4880 065G120610272





9965 000 36045

9965 000 39773

9965 000 39773

9965 000 39773

4890 065G120610272

4900 065G120610432


CHIP 0.1UF 25V X7R 1206

9965 000 39773

9965 000 39774

4930 067G215Y1007KT LOW ESR EC 10UF 50V EG1H100MPN05 9965 000 43652

4940 067G215Y1007KT LOW ESR EC 10UF 50V EG1H100MPN05 9965 000 43652

4950 093G6433

4960 093G6433

4970 093G6433

4980 093G6433

4990 093G6433






9965 000 35994

9965 000 35994

9965 000 35994

9965 000 35994

9965 000 35994

5000 093G6433

5010 093G6432V

5030 093G39S12T

5050 093G39S24T


LL4148-GS08

RLZ20B LLDS

RLZ 5.6B LLDS

5060 093G39S38T

5070 093G39S40T

PTZ 9.1B

RLZ 13B LLDS

5080 093G39S44T RLZ18B LLDS

5090 093G64S511SEM IN4148W

5140 061G212Y625KT

5160 071G5529GP

5170 093G6026T52T

5180 093G6038T52T

5190 056G15810T

5200 056G15812

5210 S73G17465VW

5220 S80GL19T8V1

MGFR 6.2MOHM -5% 1/2W

FERRITE BEAD


FR103

AZ431AZ-AE1

KIA431A-AT/P TO-92

TRANSFORMERS

TRANSFORMER ASS'Y

9965 000 36024

9965 000 36024

9965 000 39780

9965 000 39780

9965 000 39780

9965 000 39780

9965 000 39780

9965 000 36991

9965 000 36991

9965 000 36991

9965 000 36991

9965 000 36991

9965 000 39768

9965 000 36041

9965 000 36041

9965 000 36041

9965 000 36041

9965 000 36041

9965 000 36041

9965 000 36041

9965 000 36041

9965 000 36041

9965 000 36041

9965 000 36041

9965 000 35994

9965 000 39775

9965 000 39776

9965 000 36079

9965 000 36080

9965 000 39777

9965 000 39778

9965 000 39779

9965 000 36083

9965 000 39733

9965 000 36030

9965 000 36095

9965 000 36101

9965 000 36054

9965 000 39227

9965 000 38142


Item TPV 18NC

10 089G728GAA901

Description

SIGNAL CABLE

20

30

089G179E30C7 FFC CABLE 30P 205MM P1.0

089G414A18NLSC MAINSCORD CCEE 10A 1M8 DET BK

40

60

705GZ-000036

705GZV34003

MAIN FRAME ASSY CMO

FRONT BEZEL ASSY

110 705GZV34004 REAR COVER ASSY


200 Z34G0022WV1B STAND TOP

210 A37G00071

220 Z34G0023WV1B

HINGE

STAND BOTTOM

230 Z34G0024WV1B BASE

250 CBPC6MNNPHSB6 CONVERSATION BOARD

2840 KEPC6AP1

3010 PWPC942MR1P

60

90

A15G00322

Z33G0019WV1T

KEY BOARD

POWER BOARD ASSY

MAIN FRAME CMO

KEY BUTTON

100 Z34G0020WVA2T FRONT BEZEL PHILIPS

1 705GZ9K056004 CPU ASSY

2840 081G121GGP

2850 077G6001GCJ

2860 077G6001GCJ




2870 077G6001GCJ

2880 077G6001GCJ

2890 077G6001GCJ




Philips 12NC

9965 000 39711

9965 000 39712

9965 000 41562

9965 000 41537

9965 000 43715

9965 000 43716

9965 000 39713

9965 000 43718

9965 000 39720

9965 000 43719

9965 000 43717

9965 000 43525

9965 000 39722

9965 000 39723

9965 000 41538

9965 000 43720

9965 000 43721

9965 000 43520

9965 000 39727

9965 000 36000

9965 000 36000

9965 000 36000

9965 000 36000

9965 000 36000

2900 061L0603101

2910 061L0603102

2920 061L0603102

2930 061L0603103

2940 061L0603103

2950 065G060310332

2960 065G060310332

2970 065G060310332

2980 065G060310332

CHIPR 100 OHM -5% 1/16W





0.01UF -10% 50V X7R

0.01UF -10% 50V X7R

0.01UF -10% 50V X7R

0.01UF -10% 50V X7R

2990 065G060310332

3010 063G10747410S

0.01UF -10% 50V X7R

FILM CAPACITOR

3020 067G215D4714K ED 470UF 25V

3030 067G215D4714K ED 470UF 25V

3040 067G215D4714K ED 470UF 25V

3050 067G215D4714K ED 470UF 25V

3060 067G215D4714K ED 470UF 25V

3070 067G215D4714K ED 470UF 25V

3080 067G215D4714K ED 470UF 25V

3090 067G215D4714K ED 470UF 25V

3100 067G215L4714H

3110 067G215L4714H

3120 067G215L4714H

470UF 25V

470UF 25V

470UF 25V

3130 067G215L4714H

3140 067G215L4714H

3150 067G215L4714H

3160 067G215L4714H

470UF 25V

470UF 25V

470UF 25V

470UF 25V

3170 067G215L4714H 470UF 25V

3180 067G215S10115H 100UF 450V 18*36 105 BY HERMEI

3190 067G215S10115K 100UF 450V

3200 084G557 FUSE 3.15A 250V MET3.15

3210 093G5046028

3220 056G1393A

3230 061G58080WT


PC123Y22FZOF

8 OHM NCT

3240 065G3J2206EM

3250 065G3J2206EM

3260 065G3J2206ET

3270 065G3J2206ET

3280 065G3J2206ET

3290 065G3J2206ET

3300 065G3J5096ET

3310 065G3J5096ET

22PF 3KV

22PF 3KV

22PF 5% SL 3KV TDK

22PF 5% SL 3KV TDK

22PF 5% SL 3KV TDK

22PF 5% SL 3KV TDK

5PF 5% SL 3KV

5PF 5% SL 3KV

3320 065G3J5096ET

3330 065G3J5096ET

5PF 5% SL 3KV

5PF 5% SL 3KV



3360 065G306M2222BM 2200PF -20% 250VAC

3370 073G17465H

3380 073G17465LS

3390 073G25391T

3400 073G25391T

LINE FILTER


CHOKE

CHOKE

3410 073G25391LS CHOKE BY LI SHIN






3470 080GL19T8DN1 X'FMR DARFONTK.2006M.101

3480 080GL19T8DN1

3490 057G66721


STP10NK70ZFP

3500 061G152M10458F 100K OHM 5% 2W


3520 093G60252

3530 093G60281

3540 093G60252

3550 093G60281

SP20150


SP20150


3560 056G37961

3570 056G60810

3580 057G4174

3590 057G4174

3600 057G4174

LD7575PS SOP-8

0Z9938




3610 057G7592

3620 057G7592

3630 057G7592

3640 057G7592

3650 057G7592

3660 057G7636

3670 057G7636

3680 057G76314

3690 057G76314

3700 061G0805104

3710 061G08055600F

3720 061G1206000

3730 061G1206000

3740 061L0805000

3750 061L0805000

3760 061L0805000

3770 061L0805000

3780 061L0805102

3790 061L0805102

3800 061L0805102

3810 061L0805102

3820 061L0805102

3830 061L0805103

3840 061L0805103

RK7002

RK7002

RK7002

RK7002

RK7002

AO4828L

AO4828L

AM9945N

AM9945N

100K 0805


0 OHM 1/8W

0 OHM 1/8W












9965 000 36088

9965 000 36025

9965 000 39734

9965 000 39734

9965 000 39735

9965 000 39736

9965 000 39737

9965 000 39738

9965 000 39739

9965 000 39740

9965 000 36093

9965 000 36093

9965 000 39743

9965 000 36010

9965 000 39744

9965 000 39745

9965 000 39746

9965 000 39745

9965 000 39746

9965 000 39747

9965 000 36059

9965 000 35966

9965 000 35966

9965 000 35966

9965 000 39732

9965 000 39732

9965 000 39732

9965 000 39732

9965 000 39732

9965 000 36051

9965 000 36086

9965 000 39741

9965 000 39742

9965 000 36055

9965 000 39728

9965 000 43644

9965 000 43644

9965 000 39729

9965 000 39729

9965 000 39729

9965 000 39729

9965 000 36941

9965 000 36941

9965 000 36941

9965 000 36941

9965 000 39730

9965 000 39730

9965 000 39731

9965 000 35969

9965 000 35970

9965 000 35970

9965 000 35971

9965 000 35971

9965 000 36004

9965 000 36004

9965 000 36004

9965 000 36004

9965 000 36004

9965 000 37794

9965 000 36007

9965 000 36007

9965 000 36007

9965 000 36007

9965 000 36007

9965 000 36007

9965 000 36007

9965 000 36007

9965 000 39732

9965 000 39732

9965 000 39732

9965 000 36033

9965 000 36033

9965 000 36033

9965 000 36033

9965 000 36033

9965 000 39748

9965 000 39748

9965 000 36100

9965 000 36100

9965 000 39749

9965 000 39750

9965 000 39751

9965 000 39751

9965 000 35984

9965 000 35984

9965 000 35984

9965 000 35984

9965 000 36963

9965 000 36963

9965 000 36963

9965 000 36963

9965 000 36963

9965 000 36964

9965 000 36964

82

190CW7 LCD

3850 061L0805103

3860 061L0805103

3870 061L0805103

3880 061L0805104

3890 061L0805104

3900 061L0805105

3910 061L0805105

3920 061L0805105

3930 061L0805105

3940 061L0805105

3950 061L0805105

3960 061L0805105

3970 061L0805105

3980 061L0805184

3990 061L0805202

4000 061L08052401F

4010 061L0805304

4020 061L08053302F

4030 061L08053601F

4040 061L0805393

4050 061L0805472

4060 061L0805472

4070 061L0805472

4080 061L0805473

4090 061L08055100F

4100 061L0805513

4110 061L0805751

4120 061L0805751

4130 061L0805752

4140 061L0805752

4150 061L0805754

4160 061L0805823

4170 061L0805823

4180 061L1206000

4190 061L1206000

4200 061L1206000

4210 061L1206000

4220 061L1206000

4230 061L1206000

4240 061L1206101

4250 061L1206101

4260 061L1206101

4270 061L1206101

4280 061L1206101

4290 061L1206101

4300 061L1206102

4310 061L1206103

4320 061L1206150

4330 061L1206150

4340 061L1206150

4350 061L1206150

4360 061L1206220

4370 061L1206220

4380 061L1206339






CHIP 1M OHM 5% 1/8W

CHIP 1M OHM 5% 1/8W

CHIP 1M OHM 5% 1/8W

CHIP 1M OHM 5% 1/8W

CHIP 1M OHM 5% 1/8W

CHIP 1M OHM 5% 1/8W

CHIP 1M OHM 5% 1/8W

CHIP 1M OHM 5% 1/8W

180K OHM 1/8W

CHIP 2KOHM 1/8W


300K OM 1/8W

CHIP 33KOHM 1/8W 1%


SMD 39KOHM/0805/ -5% 1/8W






CHIP 51KOHM 1/8W

750 OHM

750 OHM

CHIP 7.5K OHM 1/10W

CHIP 7.5K OHM 1/10W


CHIP 82KOHM 1/8W

CHIP 82KOHM 1/8W













CHIP 1K OHM 5% 1/8W

CHIP 10KOHM 5% 1/4W

CHIP 15 OHM 5% 1206 1/4W

CHIP 15 OHM 5% 1206 1/4W

CHIP 15 OHM 5% 1206 1/4W

CHIP 15 OHM 5% 1206 1/4W

CHIP 22OHM 5% 8W

CHIP 22OHM 5% 8W

CHIP 3.3OHM 1/4W

4390 061L1206392

4400 061L1206392

4410 061L1206392

4420 061L1206471

4430 061L1206471

4440 061L1206472

4450 061L1206519

4460 061L1206519









4470 061L1206684

4480 061L1206684

4490 061L1206684









4550 065G080510231

4560 065G080510231

4570 065G080510231

4580 065G080510231

4590 065G080510231

4600 065G080510332

4610 065G080510432

4620 065G080510432

4630 065G080510432

4640 065G080510432

4650 065G080510432

4660 065G080510432

4670 065G080510432

1000PF 50V NPO

1000PF 50V NPO

1000PF 50V NPO

1000PF 50V NPO

1000PF 50V NPO

10NF/50V/0805/X7R

CHIP 0.1U 50V X7R

CHIP 0.1U 50V X7R

CHIP 0.1U 50V X7R

CHIP 0.1U 50V X7R

CHIP 0.1U 50V X7R

CHIP 0.1U 50V X7R

CHIP 0.1U 50V X7R

4680 065G080510432

4690 065G080510432

4700 065G080510432

4710 065G080510432

4720 065G080510432

4730 065G080510522

4740 065G080510522

4750 065G080510522

4760 065G080522131

4770 065G080522332

4780 065G080522422

4790 065G080533232

CHIP 0.1U 50V X7R

CHIP 0.1U 50V X7R

CHIP 0.1U 50V X7R

CHIP 0.1U 50V X7R

CHIP 0.1U 50V X7R




220PF 50V NPO

CHIP 0.022UF 50V X7R 0805

CHIP CAP 0.22 UF 25V X7R

3200PF/25V/X7R


9965 000 39766

9965 000 39766

9965 000 39766

9965 000 36070

9965 000 36070

9965 000 36986

9965 000 39767

9965 000 39767

9965 000 36024

9965 000 36024

9965 000 36024

9965 000 39780

9965 000 39780

9965 000 39780

9965 000 39780

9965 000 39780

9965 000 36991

9965 000 36991

9965 000 36991

9965 000 36991

9965 000 36991

9965 000 39768

9965 000 36041

9965 000 36041

9965 000 36041

9965 000 36041

9965 000 36041

9965 000 36041

9965 000 36041

9965 000 36041

9965 000 36041

9965 000 36041

9965 000 36041

9965 000 36041

9965 000 36073

9965 000 36073

9965 000 36073

9965 000 39769

9965 000 39770

9965 000 39771

9965 000 39772

9965 000 39758

9965 000 39759

9965 000 39759

9965 000 36981

9965 000 36981

9965 000 39760

9965 000 39761

9965 000 39761

9965 000 36067

9965 000 36067

9965 000 36067

9965 000 36067

9965 000 36067

9965 000 36067

9965 000 36022

9965 000 36022

9965 000 36022

9965 000 36022

9965 000 36022

9965 000 36022

9965 000 39762

9965 000 36016

9965 000 39763

9965 000 39763

9965 000 39763

9965 000 39763

9965 000 39764

9965 000 39764

9965 000 39765

9965 000 36964

9965 000 36964

9965 000 36964

9965 000 36965

9965 000 36965

9965 000 36013

9965 000 36013

9965 000 36013

9965 000 36013

9965 000 36013

9965 000 36013

9965 000 36013

9965 000 36013

9965 000 39752

9965 000 36971

9965 000 36142

9965 000 36063

9965 000 36975

9965 000 39753

9965 000 39754

9965 000 39755

9965 000 39755

9965 000 39755

9965 000 39756

9965 000 39757

5090 093G64S511SEM IN4148W

5140 061G212Y625KT MGFR 6.2MOHM -5% 1/2W

5160 071G5529GP

5170 093G6026T52T

FERRITE BEAD


5180 093G6038T52T

5190 056G15810T

5200 056G15812

5210 S73G17465VW

FR103

AZ431AZ-AE1

KIA431A-AT/P TO-92

TRANSFORMERS

TRANSFORMER ASS'Y 5220 S80GL19T8V1

067G2151007NT

067G2151007NT

9965 000 39779

9965 000 36083

9965 000 39733

9965 000 36030

9965 000 36095

9965 000 36101

9965 000 36054

9965 000 39227

9965 000 38142

9965 000 39781

9965 000 39781


Item TPV 18 nc Description

705GZ-000036

A15G00322

Main Frame ASSY CMO

Main Frame CMO

705GZV34003 Front Bezel Assy

Z33G0019WV1T Key button

Z34G0020WVA2T Front Bezel Philips

705GZV34004 Rear Cover Assy

Z34G0021WV1T Rear Cover

Q40G19E81316C RATING LABEL

Q44G90288131C craton

Q44G90341

Q44G90342

Q45G8860614

Q45G8860949

EPS(L)

EPS(R)

PE BAG

EPE COVER

Q70G90028131B E-D.F.U

Z34G0022WV1B Stand Top

Z34G0023WV1B Stand Bottom

Z34G0024WV1B BASE

C707 067G3151014K

C708 067G3151014K

C709 067G3151014K

C710 067G3151014K

EC 100uF 25V EG1E101MNN0511PU




C711 067G3151014K

C712 067G3151014K

C431 067G3154704K

C432 067G3154797K




EC 4.7uF 50V EG1H4R7MNN0511PU

C426 067G215S4713K EC 470UF 16V

U701 056G56321 AP1084K33LA

U403 056G113324

FB407 071G56D102M

AT24C16AN-10SU-2.7

CHIP HEAD 1000OHM

FB704 071G56K121M

FB703 071G56K121M

FB702 071G56K121M

FB707 071G56K121M

FB414 071G56K121M

FB413 071G56K121M

FB412 071G56K121M

FB411 071G56K121M

FB410 071G56K121M

FB408 071G56K121M

FB420 071G59B121

FB419 071G59B121

FB418 071G59B121

FB417 071G59B121

FB416 071G59B121

FB415 071G59B121

FB404 071G59B300M

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

TB160808B

TB160808B

TB160808B

TB160808B

TB160808B

TB160808B

CHIP BEAD 30 OHM

FB403 071G59B300M

FB401 071G59B300M

CHIP BEAD 30 OHM

CHIP BEAD 30 OHM

U401 705GZ9K056002 CPU ASSY

056G562117 NT68663

Z40G90008132A cpu label

Z40G90008132AS CPU software

C816 065G3J2206EM CAP FOR HIGHT VOLTAGE

C841 065G3J2206EM CAP FOR HIGHT VOLTAGE

C906 067G215Y1007KT KY50VB10M-TP5 5*11.5

C907 067G215Y1007KT KY50VB10M-TP5 5*11.5

093G6433

093G6432V


LL4148-GSO8

093G6432V

093G39S12T

093G39S24T

093G39S24T

LL4148-GSO8

RLZ20B LLDS

RLZ 5.6B LLDS

RLZ 5.6B LLDS

093G39S38T

093G39S40T

PTZ 9.1B

RLZ 13B LLDS

093G39S44T RLZ18B LLDS

093G64S511SEM IN4148W

093G64S511SEM IN4148W

093G64S511SEM IN4148W

093G64S511SEM IN4148W

093G64S511SEM IN4148W

061G212Y625KT MGFR 6.2MOHM +-5% 1/2W

061G212Y625KT MGFR 6.2MOHM +-5% 1/2W

071G5529GP

093G6026T52T

FERRITE BEAD


Philips 12NC

9965 000 41537

9965 000 41538

9965 000 43715

9965 000 43720

9965 000 43721

9965 000 43716

9965 000 43718

9965 000 43719

9965 000 43717

9965 000 43516

9965 000 37779

9965 000 43644

9965 000 43644

9965 000 43652

9965 000 43652

9965 000 35994

9965 000 39775

9965 000 39775

9965 000 39776

9965 000 36079

9965 000 36079

9965 000 36080

9965 000 39777

9965 000 39778

9965 000 39779

9965 000 39779

9965 000 39779

9965 000 39779

9965 000 39779

9965 000 36083

9965 000 36083

9965 000 39733

9965 000 36030


190CW7 LCD

83

093G6038T52T

056G15810T

056G15812

S73G17465VW

S80GL19T8V1

S80GL19T8V1

FR103

IC AZ431AZ-AE1 TO-92 BY AAC

KIA431A-AT/P TO-92

TRANSFORMATER ASSY

TRANSFORMATER ASSY

TRANSFORMATER ASSY

9965 000 36095

9965 000 36101

9965 000 36054

9965 000 39227

9965 000 38142

9965 000 38142


Item TPV 18NC Description

Z34G0024WV1B BASE

Q44G90288131C craton

089G728SAAA00 D-SUB CABLE

Q70G90028131B E-D.F.U

Q45G8860952 EPE COVER

Q44G90341

Q44G90342

EPS(L)

EPS(R)

Philips 12NC

9965 000 43717

9965 000 44523

A33G0067VO1T

705GZ-000036

A15G00322

Key Button

Main Frame ASSY CMO

Main Frame CMO

9965 000 39716

9965 000 41537

9965 000 41538

089G412A18NIS1 MAINSCORD AUS/NZ 10A 1M8 BK 9965 000 44230

089G412A18NLS1 MAINSCORD AUS/NZ 7A5 1M8 BK 9965 000 44524

Q45G7628B05

A33G00601C

PE BAG

Power Lens

Q40G19E81316C RATING LABEL

Z34G0021WV1T

705GZV34004

Rear Cover

Rear Cover Assy

9965 000 39714

089G728GAA901

089G728CAA901

Z34G0023WV1B

SIGNAL CABLE

SIGNAL CABLE 1.8M

Stand Bottom

Z34G0022WV1B Stand Top

CBPC6MNNPHSB5 MPLCONVERSION BOARD

9965 000 43716

9965 000 39711

9965 000 44522

9965 000 43719

9965 000 43718

9965 000 43524

9965 000 43519 705GZ9K056003 CPU ASSY

Z40G90008135CS CPU Software

CN902 095G80141265 HARNESS 12P-12P 100mm

Diversity of 190CW7CS/00(LPL) compared with 190CW7CS/00(CMO)

Item TPV 18NC

089G404A18N IS

705GZ-000038

705GZV15003

095G8014 18 8

Z15G0006 1

705GZV34004

Z34G0021 WV 1T

750GLG90W1A11N

Q40G 19E81316C

Q44G9028813 1C

Q44G9034 1

Q44G9034 2

Q45G 88609 52

Q70G9002813 1B

Z34G0023 WV 1B

Z34G0024 WV 1B

Z34G0031 WV 1T

CBPC6GNNPHS

C707 067G 315101 4K

C708 067G 315101 4K

C709 067G 315101 4K

C710 067G 315101 4K

C711 067G 315101 4K

C712 067G 315101 4K

C431 067G 315470 4K

C432 067G 315479 7K

C426 067G215S471 3K

U701 056G 563 21

U403 056G1133 24

FB407 071G 56D102 M

FB707 071G 56K121 M

FB704 071G 56K121 M

FB703 071G 56K121 M

FB702 071G 56K121 M

FB414 071G 56K121 M

FB413 071G 56K121 M

FB412 071G 56K121 M

FB411 071G 56K121 M

FB410 071G 56K121 M

FB408 071G 56K121 M

FB420 071G 59B121

FB419 071G 59B121

FB418 071G 59B121

FB417 071G 59B121

FB416 071G 59B121

FB415 071G 59B121

FB404 071G 59B300 M

FB403 071G 59B300 M

FB401 071G 59B300 M

Description

POWER CORD

Front Bezel ASSY HP CMO

Main Frame ASSY- LPL

HARNESS 18P-12P 180mm

Main framMain frame - LPL

Rear Cover Assy

Rear Cover

PANEL LM190WX1-TLA1 LPL

RATING LABEL craton

EPS(L)

EPS(R)

EPE COVER

E-D.F.U

Stand Bottom

BASE

Stand Top

MPLCONVERSION BOARD

EC 100uF 25V EG1E101MNN0511PU 6.3*11mm






EC 47uF 25V EG1E470MNN0511PU 5*11mm

EC 4.7uF 50V EG1H4R7MNN0511PU 5*11mm

EC 470UF 16V

AP1084K33LA

AT24C16AN-10SU-2.7

CHIP HEAD 1000OHM

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

TB160808B

TB160808B

TB160808B

TB160808B

TB160808B

TB160808B

CHIP BEAD 30 OHM

CHIP BEAD 30 OHM

CHIP BEAD 30 OHM

705GZV56019

100CZ101000031

Z40G900081335A

CPU ASSY

CPU software

CPU Label

C816 065G 3J2206EM

C841 065G 3J2206EM

CAP FOR HIGHT VOLTAGE


R905 061G152M10458F GP 100K OHM 5% 2W

R914 061G152M47858F GP RST MOFR 0.47OHM +-5% 2WS

C906 067G215Y1007KT

C907 067G215Y1007KT

IC903 056G 158 10 T

KY50VB10M-TP5 5*11.5

KY50VB10M-TP5 5*11.5


Diversity of 190CW7CS/00(AUO) compared with 190CW7CS/00(CMO)


089G 728CAA901 SIGNAL CABLE 1.8M-AUO

089G 728SAAA00

D-SUB Cable-AUO

705GZV15005

Z15G0007 1

Main Frame ASSY- AUO

Main Frame

705GZV34005 front bezel assy- AUO

Z34G0027 VOA2T front bezel

750GLU90W1012N PANEL LCD 19" PW01 V00 AUO

CBPC7ANNPHS MPLCONVERSION BOARD-AUO

C707 067G 315101 4K

C708 067G 315101 4K

C709 067G 315101 4K

C710 067G 315101 4K

C711 067G 315101 4K

C712 067G 315101 4K

C431 067G 315470 4K

C432 067G 315479 7K









C426 067G215S471 3K EC 470UF 16V

U701 056G 563 21 AP1084K33LA

U403 056G1133 24

FB407 071G 56D102 M

FB707 071G 56K121 M

AT24C16AN-10SU-2.7

CHIP HEAD 1000OHM

CHIP BEAD

FB704 071G 56K121 M

FB703 071G 56K121 M

FB702 071G 56K121 M

FB414 071G 56K121 M

FB413 071G 56K121 M

FB412 071G 56K121 M

FB411 071G 56K121 M

FB410 071G 56K121 M

FB408 071G 56K121 M

FB420 071G 59B121

FB419 071G 59B121

FB418 071G 59B121

FB417 071G 59B121

FB416 071G 59B121

FB415 071G 59B121

FB404 071G 59B300 M

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

TB160808B

TB160808B

TB160808B

TB160808B

TB160808B

TB160808B

CHIP BEAD 30 OHM

FB403 071G 59B300 M

FB401 071G 59B300 M

CHIP BEAD 30 OHM

CHIP BEAD 30 OHM

705GZV56021 CPU ASSY

100CZ101000051 CPU software

Z40G900081353A CPU Label

Diversity of 190CW7CS/93(LPL) compared with 190CW7CS/00(CMO)

Item TPV 18NC

089G414A18NLSC

705GZ-000038

705GZV15003

095G8014 18 8

Z15G0006 1

705GZV34004

Z34G0021 WV 1T

750GLG90W1A11N

Q44G9044A01

Q44G9044A02

Q45G 88609 52

Q70G9002813 1B

Z34G0023 WV 1B

Z34G0024 WV 1B

Z34G0031 WV 1T

Z44G9001813 1B

CBPC7GNNPHSA4

C707 067G 315101 4K

C708 067G 315101 4K

C709 067G 315101 4K

C710 067G 315101 4K

C711 067G 315101 4K

C712 067G 315101 4K

C431 067G 315470 4K

Description

MAINSCORD CCEE 10A 1M8 DET BK

Front Bezel ASSY HP CMO

Main Frame ASSY LPL


Main framMain frame LPL

Rear Cover Assy

Rear Cover


EPS(L)

EPS(R)

EPE COVER

E-D.F.U

Stand Bottom

BASE

Stand Top

CARTON

MPLCONVERSION








84

190CW7 LCD


C432 067G 315479 7K

C426 067G215S471 3K

U701 056G 563 21

U403 056G1133 24

FB407 071G 56D102 M

FB707 071G 56K121 M

FB704 071G 56K121 M

FB703 071G 56K121 M

FB702 071G 56K121 M

FB414 071G 56K121 M

FB413 071G 56K121 M

FB412 071G 56K121 M

FB411 071G 56K121 M

FB410 071G 56K121 M

FB408 071G 56K121 M

FB420 071G 59B121

FB419 071G 59B121

FB418 071G 59B121


EC 470UF 16V

AP1084K33LA

AT24C16AN-10SU-2.7

CHIP HEAD 1000OHM

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

TB160808B

TB160808B

TB160808B

FB417 071G 59B121

FB416 071G 59B121

FB415 071G 59B121

FB404 071G 59B300 M

FB403 071G 59B300 M

FB401 071G 59B300 M

705GZV56025

100CZ101000091

Z40G900081347A

C816 065G 3J2206EM

TB160808B

TB160808B

TB160808B

CHIP BEAD 30 OHM

CHIP BEAD 30 OHM

CHIP BEAD 30 OHM

CPU ASSY

CPU Software

CPU Label


C841 065G 3J2206EM CAP FOR HIGHT VOLTAGE

R905 061G152M10458F GP 100K OHM 5% 2W


C906 067G215Y1007KT KY50VB10M-TP5 5*11.5

C907 067G215Y1007KT

IC903 056G 158 10 T

KY50VB10M-TP5 5*11.5


Diversity of 190CW7CS/93(AUO) compared with 190CW7CS/00(CMO)


089G 728CAA901 SIGNAL CABLE 1.8M

089G 728SAAA00

D-SUB CABLE

705GZV15005

Z15G0007 1

Main Frame ASSY-AUO

Main Frame-AUO

705GZV34005 front bezel assy-AUO

Z34G0027 VOA2T front bezel-AUO

750GLU90W1012N PANEL LCD 19" PW01 V00 AUO

CBPC7ANNPHSA2 MPLCONVERSION BOARD

C707 067G 315101 4K

C708 067G 315101 4K

C709 067G 315101 4K

C710 067G 315101 4K





C711 067G 315101 4K

C712 067G 315101 4K

C431 067G 315470 4K

C432 067G 315479 7K





C426 067G215S471 3K EC 470UF 16V

U701 056G 563 21 AP1084K33LA

U403 056G1133 24

FB407 071G 56D102 M

AT24C16AN-10SU-2.7

CHIP HEAD 1000OHM

FB707 071G 56K121 M

FB704 071G 56K121 M

FB703 071G 56K121 M

CHIP BEAD

CHIP BEAD

CHIP BEAD

FB702 071G 56K121 M

FB414 071G 56K121 M

FB413 071G 56K121 M

FB412 071G 56K121 M

FB411 071G 56K121 M

FB410 071G 56K121 M

FB408 071G 56K121 M

FB420 071G 59B121

FB419 071G 59B121

FB418 071G 59B121

FB417 071G 59B121

FB416 071G 59B121

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

TB160808B

TB160808B

TB160808B

TB160808B

TB160808B

FB415 071G 59B121

FB404 071G 59B300 M

FB403 071G 59B300 M

FB401 071G 59B300 M

TB160808B

CHIP BEAD 30 OHM

CHIP BEAD 30 OHM

CHIP BEAD 30 OHM

705GZV56036 CPU ASSY

100CZ101000221 CPU software

Z40G900081355A CPU Label


Diversity of 190CW7CB/93(LPL) compared with 190CW7CS/00(CMO)

Item

1060

1060

18NC

089G 728CAA901

089G 728GAA901

1060

1060

089G 728HAA550

089G 728SAAA00

SZ001 705GZV01025

SZ004 705GZV15003

SZ005 095G8014 18 8

SZ006 705GZV34003

SZ007 705GZV34004

SZ008 750GLG90W1A11N

SZ009 A37G0007 1

SZ010 Q40G 19E81316C

SZ011 Q44G9044A01

SZ012 Q44G9044A02

SZ013 Q45G 88609 52

SZ014 Z34G0024 WV 1B

SZ015 Z44G9001813 1B

SZ016 CBPC7GNNPHSA4

C707 067G 315101 4K

C708 067G 315101 4K

C709 067G 315101 4K

C710 067G 315101 4K

C711 067G 315101 4K

C712 067G 315101 4K

C431 067G 315470 4K

C432 067G 315479 7K

Description

SIGNAL CABLE 1.8M

SIGNAL CABLE

SIGNAL CABLE D-SUB HONGLIN

D-SUB CABLE

DFU Assy

Main Frame ASSY LPL


Front Bezel Assy

Rear Cover Assy


HINGE

RATING LABEL

EPS(L)

EPS(R)

EPE COVER

BASE

CARTON

MPLCONVERSION









C426 067G215S471 3K

U701 056G 563 21

U403 056G1133 24

FB407 071G 56D102 M

FB707 071G 56K121 M

FB704 071G 56K121 M

FB703 071G 56K121 M

FB702 071G 56K121 M

FB414 071G 56K121 M

FB413 071G 56K121 M

FB412 071G 56K121 M

FB411 071G 56K121 M

FB410 071G 56K121 M

FB408 071G 56K121 M

FB420 071G 59B121

FB419 071G 59B121

EC 470UF 16V

AP1084K33LA

AT24C16AN-10SU-2.7

CHIP HEAD 1000OHM

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

CHIP BEAD

TB160808B

TB160808B

FB418 071G 59B121

FB417 071G 59B121

FB416 071G 59B121

FB415 071G 59B121

FB404 071G 59B300 M

FB403 071G 59B300 M

FB401 071G 59B300 M

705GZV56025

TB160808B

TB160808B

TB160808B

TB160808B

CHIP BEAD 30 OHM

CHIP BEAD 30 OHM

CHIP BEAD 30 OHM

CPU ASSY

C816 065G 3J2206EM

C841 065G 3J2206EM



R905 061G152M10458F GP 100K OHM 5% 2W


C906 067G215Y1007KT KY50VB10M-TP5 5*11.5

C907 067G215Y1007KT

IC903 056G 158 10 T

KY50VB10M-TP5 5*11.5


190CW7 LCD

85

86

190CW7 LCD

Manual 3138 106 10544

-First release

-ALL chapters

Revision List

According to CP SZ00087 , 190CW7 some models are updated some material code number as following.

Model name Scaler board

190CW7CS/00(CMO) CBPC6MNNPHA

190CW7CS/75(CMO) CBPC6MNNPHSB5

190CW7CB/69(CMO) CBPC6MNNPHSB4

190CW7CB/93(CMO) CBPC6MNNPHSB6





CPU assy

705GZ9K0 56002

705GZ9K0 56003

705GZ9K0 56001

705GZ9K0 56004

705GZ9K0 56006

705GZ9K0 56001

705GZ9K0 56004

705GZ9K0 56005

TELEVISION/MONITOR SAFFTY GUIDELINES FOR THE PROFESSIONAL SERVICE TECHNICIAN

Safety Checks

After the original service problem has been corrected,a complete safety check should be made. Be sure to check over the entire set, not just the areas where you have worked. Some previous servicer may have left an unsafe condition,which could be unknowingly passed on to your customer. Be sure to check all of the following:

Fire and Shock Hazard

1. Be sure all components are positioned in such a way as to avoid the possibility of adjacent component shorts. This is especially important on those chassis which are transported to and from the service shop.

2. Never release a repaired unit unless all protective devices such as insulators, barries, covers, strain reliefs, and other hardware have been installed in accordance with the original design.

3. Soldering and wiring must be inspected to locate possible cold solder joints,solder splashes,sharp solder points, frayed leads, pinched leads, or damaged insulation ( including the ac cord).Be certain to remove loose solder balls and all other loose foreign particles.

4. Check across-the-line components and other components for physical evidence of damage or deterioration and replace if necessary. Follow original layout,lead length, and dress.

5. No lead or component should touch a receiving tube or a resistor rated at 1 watt or more. Lead tension around protruding metal surfaces or edges must be avoided.

6. Critical components having special safety characteristics are identified with ans by the Ref. No. in the parts list and enclosed within a broken line

* (where several critical components are grouped in one area) along with the safety symbols on the schematic diagrams and/or exploded views.

7. When servicing any unit, always use a separate isolation transformer for the chassis Failure to use a separate isolation transformer may expose you to possible shock hazard, and may cause damage to servicing instruments.

8. Many electronic products use a polarized ac line cord (one wide pin on the plug.) Defeating this safety feature may create a potential hazard to the service and the user. Extension cords which do not incorporate the polarizing feature should never be used.

9. After reassembly of the unit, always perform an leakage test or resistance test from the line cord to all exposed metal parts of the cabinet. Also check all metal control shafts(with knobs removed), antenna terminals, handles, screws, etc. to be sure the unit may be safety operated without danger of electrical shock.

6. New picture tubes are specifically designed to withstand higher operathng voltages without creating undesirable X-radiation. It is strongly recommended that any shop test fixture which is to be used with the new higher voltage chassis be equipped with one of the new type tubes designed for this service. Addition of a permanently connected HV meter to the shop test fixture is advisable. The CRT types used in these new sets should never be replaced with any other types, as this may result in excessive X-radiation.

7. It is essential to use the specified picture tube to avoid a possible X-diation problem.

8. Most TV receivers contain some type of emergency "Hold Down" circuit to prevent HV from rising to excessive levels in the presence of a failure mode. These various circuits should be understood by all technicians servicing them, especially since many hold down circuits are inoperative as long as the receiver performs normally.

Leakage Current Cold Check

1. Unplug the ac line cord and connect a jumper between the two prongs of the plug.

2. Turn on the power switch.

3. Measure the resistance value between the jumpered ac plug and all exposed cabinet parts of the receiver, such as screw heads, antennas, and control shafts. When the exposed metallic part has a return path to the chassis, the reading should be between 1 megohm and 5.2 megohms.

When the exposed metal does not have a return path to the chassis, the reading must be infinity. Remove the jumper from the ac line cord.

TO

INSTRUMENTS

EXPOSED

METAL PARTS

0.15 uF

1500 ohm, 10W

WATER

PIPE

EARTH

GROUND

* Broken line

Implosion

1. All picture tubes used in current model receivers are equipped with an integral implosion system. Care should always be used, and safety glasses worn,whenever handling any picture tube. Avoid scratching or otherwise damaging the picture tube during installation.

2. Use only replacement tubes specified by the manufacturer.

X-radiation

1. Be sure procedures and instructions to all your service personnel cover the subject of X-radiation. Potential sources of X-rays in TV receivers are the picture tube and the high voltage circuits. The basic precaution which must be exercised is to keep the high voltage at the factory recommended level.

2. To avoid possible exposure to X-radiation and electrical shock, only the manufacturer's specified anode connectors must be used.

3. It is essential that the service technician has an accurate HV meter available at all times. The calibration of this meter should be checked periodically against a reference standard.

4. When the HV circuitry is operating properly there is no possibility of an xradiation problem. High voltage should always be kept at the manufacturer's rated value-no higher - for optimum performance. Every time a color set is serviced, the brightness should be run up and down while monitoring the

HV with a meter to be certain that the HV is regulated correctly and does not exceed the specified value. We suggest that you and your technicians review test procedures so that HV and HV regulation are always checked as a standard servicing procedure, and the reason for this prudent routine is clearly understood by everyone. It is important to use an accurate and reliable HV meter. It is recommended that the HV recorded on each customer's invoice, which will demonstrate a proper concern for the customer's safety.

5. When troubleshooting and making test measurements in a receiver with a problem of excessive high voltage, reduce the line voltage by means of a Variac to bring the HV into acceptable limits while troubleshooting. Do

Leakage Current Hot Check

1. Do not use an isolation transformer for this test. Plug the completely reassembled receiver directly into the ac outlet.

2. Connect a 1.5k, 10w resistor paralleled by a 0.15uf. capacitor between each exposed metallic cabinet part and a good earth ground such as a water pipe, as shown above.

3. Use an ac voltmeter with at least 5000 ohms volt sensitivity to measure the potential across the resistor.

4. The potential at any point should not exceed 0.75 volts. A leakage current tester may be used to make this test; leakage current must not exceed

0.5 milliamps. If a measurement is outside of the specified limits, there is a possibility of shock hazard. The receiver should be repaired and rechecked before returning it to the customer.

5. Repeat the above procedure with the ac plug reversed.( Note: An ac adapter is necessary when a polarized plug is used. Do not defeat the polarizing feature of the plug.)

Picture Tube Replacement

The primary source of X-radiation in this television receiver is the picture tube. The picture tube utilized in this chassis is specially constructed to limit

X-radiation emissions. For continued X-radiation protection, the replacement tube must be the same type as the original, including suffix letter, or a Philips approved type.

Parts Replacement

Many electrical and mechanical parts in Philips television sets have special safety related characteristics. These characteristics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. The use of a substitute part which does not have the same safety characteristics as the Philips recommended replacement part shown in this service manual may create shock, fire, or other hazards

WARNING

:

SERVICE NOTE

:

Before removing the CRT anode cap, turn the unit

The CRT DAG is not at chassis ground.

OFF

and short the HIGH VOLTAGE to the CRT DAG ground.

Philips 190cw7

TABLE OF CONTENTS

FAQs (Frequently Asked Questions)-------------13~14

Firmware Upgrade for CPU-

Failure Mode Of Panel -

SAFETY NOTICE

LCD panel

/ to confirm

To adjust contrast of the display

Kensington anti-thief lock

AC power input

DVI-D input

VGA input

Description of the On Screen Display

The OSD Tree

Front Control

To Lock/Unlock OSD FUNCTION(User Mode)

Access Factory Mode

Unlock OSD function

Access Aging Mode

4. Access Factory Mode

General

Configuration and procedure

Step 1: After initialize alignment box, connecting all cables and box as shown in Fig. 10.

Step 3: Modify DDC data (verify EDID version, week, year)

Step 2: Read DDC data from monitor

Click this button

Select and fill out,

If necessary.

Step 4: Modify DDC data (Monitor Serial No.)

Step 5: Write DDC data

2. Access Factory Mode

Step 6: Save DDC data

Step 7: Exit DDC program

Step 1: After initialize alignment box, connecting all cables and box as shown in Fig. 31.

Step 2: Read DDC data from monitor

Step 4: Modify DDC data (Monitor Serial No.)

Step 3: Modify DDC data (verify EDID version, week, year)

Step 7: Exit DDC program

Step 5: Write DDC data

2. Access Factory Mode

Step 8: Turn off the monitor, exit the factory mode.

Step 6: Save DDC data

Firmware Upgrade for CPU

Configuration and procedure

System and equipment requirements

Update the firmware

Firmware Upgrade for CPU

Go to cover page

PIXEL

SEPARATE SYNC.

C

VIDEO

D

E

HORIZONTAL

B

Q

A

VIDEO

R

S

VERTICAL

P

O

COMPOSITE SYNC.

C

VIDEO

D

E

HORIZONTAL

B

A

FIG-4 TIMING CHART -1

- Oxidation on the terminals of SMDs results in poor soldering.

Do not handle SMDs with bare hands.

- Avoid using storage places that are sensitive to oxidation such as places with sulphur or chlorine gas, direct sunlight, high temperatures or a high degree of humidity. The capacitance or resistance value of the SMDs may be affected by this.

Similarly, do not slide the circuit board across any surface.

preferably be equipped with a thermal control (soldering temperature: 225 to 250 C).

- The chip, once removed, must never be reused.