R5X-05 BIKE SERVICE MANUAL

Add to my manuals
79 Pages

advertisement

R5X-05 BIKE SERVICE MANUAL | Manualzz

R 5 X - 0 5 B I K E

S E R V I C E M A N U A L

TABLE OF CONTENTS

4.1

4.2

4.3

4.4

4.5

4.6

4.7

2.1

2.2

3.1

3.2

3.3

5.1

5.2

6.1

7.1

8.1

8.2

8.3

8.4

8.5

8.6

8.7

8.8

8.9

8.10

8.11

8.12

8.13

CHAPTER 1: SERIAL NUMBER LOCATION ........................................................... 1

CHAPTER 2: IMPORTANT SAFETY INSTRUCTIONS

Read and Save These Instructions ............................................................................ 3

Electrical Requirements ............................................................................................. 4

CHAPTER 3: PREVENTATIVE MAINTENANCE

Recommended Cleaning Tips .................................................................................... 5

Check for Damaged Parts ......................................................................................... 5

Care and Maintenance Instructions ........................................................................... 6

CHAPTER 4: CONSOLE OVERLAY AND WORKOUT DESCRIPTION

Console Description .................................................................................................. 7

Workout Setup Steps - Manual .................................................................................. 8

Workout Setup Steps - Fat Burn ................................................................................ 8

Workout Setup Steps - Level Based .......................................................................... 8

Workout Setup Steps - Fitness Test ........................................................................... 9

Workout Setup Steps - Target Heart Rate ................................................................. 10

Workout Setup Steps - Constant Watts ..................................................................... 10

CHAPTER 5: MANAGER MODE

Using Manager Mode ................................................................................................ 11

Manager Mode Overview ........................................................................................... 11

CHAPTER 6: ENGINEERING MODE

Using Engineering Mode ............................................................................................ 12

CHAPTER 7: SERVICE MODE

Using Service Mode ................................................................................................... 13

CHAPTER 8: TROUBLESHOOTING

Electrical Diagram ...................................................................................................... 14

LCB LED Indicators .................................................................................................... 19

Troubleshooting - Error 04A0 / 0440 .......................................................................... 20

Troubleshooting - Error 04B0 ...................................................................................... 21

Troubleshooting - Error 0248 ...................................................................................... 22

Troubleshooting - Error 0247 ...................................................................................... 23

Troubleshooting - Error 02B4 / 03A8 / 02AB / 0441 ................................................... 23

Troubleshooting - Error 0149 / 01AF .......................................................................... 24

Troubleshooting - Error 01B4 ...................................................................................... 25

Troubleshooting - No Resistance ............................................................................... 26

Troubleshooting - Heart Rate Issues ......................................................................... 27

Troubleshooting - No Power to the Console .............................................................. 28

Troubleshooting - Keypad Issues ............................................................................... 29

TABLE OF CONTENTS

9.9

9.10

9.11

9.12

9.13

9.14

9.15

9.16

9.1

9.2

9.3

9.4

9.5

9.6

9.7

9.8

9.17

9.18

9.19

9.20

9.21

9.22

9.23

9.24

10.1

10.2

10.3

10.4

10.5

11.1

CHAPTER 9: PART REPLACEMENT GUIDE

Console Replacement ..................................................................................................... 30

Handlebar Replacement ................................................................................................ 31

Cup Holder Replacement .............................................................................................. 32

Keypad / Overlay Replacement ...................................................................................... 33

Seat Pad Replacement ................................................................................................... 35

Back Pad Replacement .................................................................................................. 36

HR Grips Replacement ................................................................................................... 37

Seat Set Replacement .................................................................................................... 38

Seat Slide Replacement ................................................................................................. 39

Rear Covers Replacement ............................................................................................ 41

Guide Rail Set Replacement .......................................................................................... 42

Pedal Replacement ........................................................................................................ 43

Crank Axle Set Replacement .......................................................................................... 44

Front Shrouds Replacement ........................................................................................... 45

Front Covers Replacement ............................................................................................. 46

Console Mast Removal ................................................................................................... 47

Lower Control Board Replacement ................................................................................ 48

Battery Replacement ...................................................................................................... 49

Drive Belt Replacement ................................................................................................. 50

Generator Replacement.................................................................................................. 51

Rear Stabilizer Replacement .......................................................................................... 52

Front Stabilizer Replacement ......................................................................................... 53

Drive Axle Set Replacement ........................................................................................... 54

Testing the Bike ............................................................................................................... 58

CHAPTER 10: BIKE SPECIFICATIONS AND ASSEMBLY GUIDE

R5x-05 Bike Specifications ......................................................................................... 59

Assembly Instructions ................................................................................................ 60

Adjusting the Pedal Straps and Seat .......................................................................... 67

Leveling the Bike ......................................................................................................... 68

TV Bracket Installation Instructions

............................................................................ 69

CHAPTER 11: SOFTWARE UPGRADE GUIDE

Software Upgrade Procedure ..................................................................................... 74

III

1.1 SERIAL NUMBER LOCATION

CHAPTER 1: SERIAL NUMBER LOCATION

FRAME SERIAL NUMBER LOCATION

1

2

CHAPTER 1: SERIAL NUMBER LOCATION

1.1 SERIAL NUMBER LOCATION - CONTINUED

CONSOLE SERIAL NUMBER LOCATION

SN # PLACEMENT

CHAPTER 2: IMPORTANT SAFETY INSTRUCTIONS

2.1 READ AND SAVE THESE INSTRUCTIONS

To ensure your safety and protect the equipment, read all instructions before operating the MATRIX R5x-05 Bike.

To ensure proper use of the Matrix R5x-05 Bike, make sure that all users read this manual. Remind the users that before undertaking any fitness program, they should obtain complete physical examinations from their physicians. If, at any time while exercising, the user experiences dizziness, pain, or shortness of breath, nausea or feels faint, he or she must stop immediately.

* This bike is only to be used for its intended purpose described in this manual. Do not use attachments that have not been recommended by Matrix.

* Never drop or insert objects into any opening. Keep hands away from moving parts. If the item cannot be reached, contact a Matrix authorized dealer for assistance.

* Never operate the unit if it is damaged, not working properly, when it has been dropped, or has been in water.

* Keep hands and feet clear at all times from moving parts to avoid injury.

* Do not use this product outdoors, near swimming pools or in areas of high humidity.

* Do not operate where aerosol (spray) products are being used or when oxygen is being administered.

* Do not use this product in bare feet. Do not wear shoes with heels, leather soles, cleats, or spikes while exercising.

* Do not remove the side covers. Service should only be done by an authorized service technician.

* Close supervision is necessary when used near children, invalids, or disabled people.

* When the bike is in use, young children and pets should be kept at least 3 meters / 10 feet away.

* Assemble and operate the bike on a solid, level surface.

* Never face backward while using the Matrix R5x-05 Bike.

* Use the stationary handlebars when mounting or dismounting the bike.

* Do not wear clothing that might catch on any moving parts of this bike.

CAUTION! If you experience chest pains, nausea, dizziness, or shortness of breath, stop exercising immediately and consult your physician before continuing.

CAUTION! Any changes or modifications to this equipment could void the product warranty.

3

4

CHAPTER 2: IMPORTANT SAFETY INSTRUCTIONS

2.2 ELECTRICAL REQUIREMENTS

110 V UNITS

All Matrix 3x, 5x, 7xe and 7xi 110 V bikes require the use of a 100-125 V, 60 Hz and a 15 A

“Dedicated Circuit”, with a non-looped (isolated) neutral/ground for power. This outlet should be a

NEMA 5-15R and have the same configuration as the plug. No adapter should be used with this product. These bikes can be daisy-chained together with up to 4 units per 15 A dedicated circuit.

Matrix daisy-chain cord adapters are sold separately.

220 V UNITS

All Matrix 3x, 5x, 7xe and 7xi 220 V bikes require the use of a 216-250 V, 50 Hz and a 15 A

“Dedicated Circuit”, with a non-looped (isolated) neutral/ground for power. This outlet should be a

NEMA 6-15R and have the same configuration as the plug. No adapter should be used with this product. These bikes can be daisy-chained together with up to 4 units per 15 A dedicated circuit.

Matrix daisy-chain cord adapters are sold separately.

110 NEMA 5-15P

PLUG

220 NEMA 6-15P

PLUG

North American power cord plugs shown.

Depending on your country, the plug type may vary.

DEDICATED CIRCUIT AND ELECTRICAL INFO

A “Dedicated Circuit” means that each outlet you plug into should not have anything else running on that same circuit. The easiest way to verify this is to locate the main circuit breaker box, and turn off the breaker(s) one at a time. Once a breaker has been turned off, the only thing that should not have power to it are the units in question. No lamps, vending machines, fans, sound systems, or any other item should lose power when you perform this test. Non-looped (isolated) neutral/grounding means that each circuit must have an individual neutral/ground connection coming from it, and terminating at an approved earth ground. You cannot “jumper” a single neutral/ground from one circuit to the next.

ELECTRICAL REQUIREMENTS

For your safety and to ensure good unit performance, the ground on this circuit must be non-looped (isolated). Please refer to NEC article 210-21 and 210-23. Any alterations to the standard power cord provided could void all warranties of this product.

The 3x, 5x and 7xe bikes are designed to be self-powered and do not require an external power supply source to operate. Without an external power supply, the console’s start-up time may be delayed. Add-on TV’s and other console accessories will increase the time needed for start-up.

An external power supply will ensure power is provided to the console at all times and is recommended when add-on accessories are used.

For units with an integrated TV (like the 7xe and 7xi), the TV power requirements are included in the unit. An RG6 coaxial cable with ‘F Type’ compression fittings on each end will need to be connected to the cardio unit and the video source. Additional power requirements are not needed for the add-on digital TV (3x and 5x). For units with an add-on PCTV (3x and 5x), the TV power requirements are separate.

GROUNDING INSTRUCTIONS

The unit must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. The unit is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. If the user does not follow these grounding instructions, the user could void the Matrix limited warranty.

ADDITIONAL ELECTRICAL INFO

In addition to the dedicated circuit requirement, the proper gauge wire must be used from the circuit breaker box, to each outlet that will have the maximum number of units running off of it. If the distance from the circuit breaker box to each outlet, is 100 ft (30.5 m) or less, then 12 gauge wire should be used. For distances greater than 100 ft (30.5 m) from the circuit breaker box to the outlet, a 10 gauge wire should be used.

ENERGY SAVING / LOW-POWER MODE

All units are configured with the ability to enter into an energy saving / low-power mode when the unit has not been in use for a specified period of time. Additional time may be required to fully reactivate this unit once it has entered the low-power mode. This energy saving feature may be enabled or disabled from within the ‘Manager Mode’ or ‘Engineering Mode.

ADD-ON PCTV (3X AND 5X)

A 15 A or 20 A “Dedicated Circuit” with a non-looped (isolated) neutral/ground is required. Each PCTV requires at least 1.2 A of current. No more than 12 PCTVs should be used for each 15 A circuit and no more than 16 PCTVs should be used for each 20 A circuit. The power outlet should have the same configuration as the plug. No adapter should be used with this product. An RG6 coaxial cable with ‘F Type’ compression fittings will need to be connected between the video source and each add-on PCTV unit.

ADD-ON DIGITAL TV (3X AND 5X)

Additional power requirements are not needed for the add-on digital TV. An RG6 coaxial cable with ‘F Type’ compression fittings will need to be connected between the video source and each add-on digital TV unit.

BATTERY CHARGING (3X AND 5X)

The bike saves its batter charge by moving into a shutdown mode whenever PEDAL FASTER appears on the display. If the user does not maintain a pedal rate of 40 RPM or higher, a 30 second shutdown process begins. When the battery voltage is low, LOW BATTERY appears on the display. This means it is time to recharge the battery. If the battery must be charged, use the optional power adapter charging unit. The charger should be connected to the bike for a minimum of eight hours to ensure a thorough charge.

CHAPTER 3: PREVENTATIVE MAINTENANCE

3.1 RECOMMENDED CLEANING TIPS

In order to maximize life span, and minimize down time, all Matrix Fitness Equipment requires regularly scheduled cleaning.

YOU WILL NEED:

- Mild dish soap and water mixture in a spray bottle (10:1 water to soap ratio).

- Lint free 100% cotton cleaning cloths or Microfiber cleaning cloths.

- Vacuum / Shop Vac with extendable hose and soft brush attachment.

- Corrosion Block (available from Matrix - part # ZMS4001374).

DAILY:

1. Wipe down the unit after each use with a mild dish soap and water mixture. NOTE: Spray the soap / water mixture onto the cloth.

NEVER spray directly onto the equipment. We recommend that you do NOT allow customers to use spray bottles to clean the equipment. If the cleaner is sprayed directly on the equipment or over spray is present, it may cause your equipment to rust and / or cause damage to console overlays.

2. With a clean dry 100% lint free cloth and water / soap mixture, wipe any dust or dirt from the out of the seat wheel track (Figure A).

WEEKLY:

1. With a clean dry 100% lint free cloth and water / soap mixture, wipe down the entire frame so it is free of dust, dirt, and sweat.

2. With a clean dry 100% lint free cloth and water / soap mixture, wipe down the entire console area including the hand grips and hand rails.

MONTHLY:

1. Vacuum under and around the Bike. If you need to move it, unplug the unit first.

2. Remove the shrouds and use a vacuum to remove any dust or dirt built up under the covers. NOTE: Be careful not to damage or unplug any of the wiring.

3. Apply Corrosion Block to the metal part of the iPod cable.

FIGURE A

3.2 CHECK FOR DAMAGED PARTS

DO NOT use any equipment that is damaged or has worn or broken parts. Use only replacement parts supplied by Matrix Fitness Systems.

MAINTAIN LABELS AND NAMEPLATES. Do not remove labels for any reason. They contain important information. If unreadable or missing, contact Matrix Fitness Systems for a replacement. 1-866-693-4863, www.matrixfitness.com

MAINTAIN ALL EQUIPMENT Preventative maintenance is the key to smooth operating equipment. Equipment needs to be inspected at regular intervals. Defective components must be replaced immediately. Improperly working equipment must be kept out of use until it is repaired.

Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is qualified to do so. Matrix Fitness Systems will provide service and maintenance training at our corporate facility upon request or in the field if proper arrangements are made.

5

6

CHAPTER 3: PREVENTATIVE MAINTENANCE

3.3 CARE AND MAINTENANCE INSTRUCTIONS

In order to maximize life span, and minimize down time, all MATRIX equipment requires regular cleaning, and maintenance items performed on a scheduled basis. This section contains detailed instructions on how to perform these items and the frequency of which they should be done.

Some basic tools and supplies will be necessary to perform these tasks which include (but may not be limited to):

* Metric Allen wrenches

* #2 Phillips head screwdriver

* Adjustable wrench

* Commercial Pedal wrench (available from Matrix - part # ZMS4001254)

You may periodically see addendums to this document, as the Matrix Technical Support Team identifies items that require specific attention, the latest version will always be available on the Matrix web site at www.matrixfitness.com.

DAILY MAINTENANCE ITEMS

1) Look and listen for loose fasteners, unusual noises, and any other indications that the equipment may be in need of service.

2) Attempt to wobble the unit from side to side and front to back. Level if needed (see Section 10.4).

WEEKLY MAINTENANCE ITEMS

1) Check the pedal straps for damage.

2) Clean the grooves on the foot pedals.

MONTHLY MAINTENANCE ITEMS

1) Frequently vacuum the floor beneath the unit to prevent the accumulation of dust and dirt which can affect the smooth operation of the unit.

2) Check that the pedal and crank assembly are tight with no free play or wobble in them. Make sure to use a commercial grade pedal wrench to get the pedals as tight as possible.

3) Check the condition of the seat upholstery. Make sure that the seat adjustment mechanism is operating correctly.

4) Check the seat for looseness. Tighten the seat rollers if needed.

5) Clean any debris off of the seat guide rail.

YEARLY MAINTENANCE ITEMS

1) Remove the front shrouds and check the belt for damage, alignment, and proper tension.

CHAPTER 4: CONSOLE OVERLAY AND WORKOUT DESCRIPTION

4.1 CONSOLE DESCRIPTION

WORKOUT KEYS: Simple program view and selection buttons.

GO: One touch Start.

UP / DOWN LEVEL: Easy information and level selection.

UP / DOWN TIME: Easy information and time adjustment.

STOP: Ends workout and shows workout summary data.

NUMBER KEYPAD: Workout data input for workout setup. Level adjustment during workout.

COOL DOWN: Puts bike into Cool Down mode.

FAN: Allows for fan speed selection (fan has 3 operating speeds).

TOGGLE DISPLAY: Allows user to select what information is displayed on the console.

LANGUAGE: Select Language.

7

8

CHAPTER 4: CONSOLE OVERLAY AND WORKOUT DESCRIPTION

4.2 WORKOUT SETUP STEPS - MANUAL

GO

- Press to immediately begin a workout. Workout, resistance level, and time will automatically go to default settings. Pressing

GO will not prompt user for age, weight, or level settings.

1) Start pedaling and press the GO key to begin your workout. 2)

The display will read 3, 2, 1, Begin and then the program will start.

MANUAL -

Manual allows the user to input more information while defining their own workout. Calorie expenditure will be more accurate when inputting information in Manual than by pressing GO.

1) Start pedaling, press the MANUAL key. Then press ENTER.

2) Select Level by using the UP or DOWN LEVEL keys and press

ENTER.

3) Select Time by using the UP or DOWN LEVEL keys and press

ENTER.

4) Select Weight by using the UP or DOWN LEVEL keys and press

ENTER.

5) Press GO, and then the display will read 3, 2, 1, Begin and then the program will start.

4.3 WORKOUT SETUP STEPS - FAT BURN

FAT BURN

- Fat burn is a level based program that is designed to help users burn fat through various resistance level changes.

1) Start pedaling and press the FAT BURN key. Then press

ENTER.

2) Select Level by using the UP or DOWN LEVEL keys and press

ENTER.

3) Select Time by using the UP or DOWN LEVEL keys and press

ENTER.

4) Select Weight by using the UP or DOWN LEVEL keys and press

ENTER.

5) Press GO, then the display will read 3, 2, 1, Begin and then the program will start.

4.4 WORKOUT SETUP STEPS - LEVEL BASED

ROLLING HILLS

- The Rolling Hills program is a level based program that automatically adjusts the resistance level to simulate real terrain.

1) Start pedaling and press the ROLLING HILLS key. Then press

ENTER.

2) Select Level by using the UP or DOWN LEVEL keys and press

ENTER.

3) Select Time by using the UP or DOWN LEVEL keys and press

ENTER.

4) Select Weight by using the UP or DOWN LEVEL keys and press

ENTER.

5) Press Go, then the display will read 3, 2, 1, Begin and then the program will start.

INTERVAL TRAINING

- The Interval Training program is a level based program that automatically adjusts the resistance of the machine from low to high intensity settings at regular intervals.

1) Start pedaling and press the INTERVAL TRAINING key. Then press ENTER.

2) Select Level by using the UP or DOWN LEVEL keys and press

ENTER.

3) Select Time by using the UP or DOWN LEVEL keys and press

ENTER.

4) Select Weight by using the UP or DOWN LEVEL keys and press

ENTER.

5) Press GO then the display will read 3, 2, 1, Begin and then the program will start.

RANDOM

- Random is a level based workout that randomly adjusts the resistance of the machine.

1) Start pedaling and press the key next to RANDOM key. Then press ENTER.

2) Select Level by using the UP or DOWN LEVEL keys and press

ENTER.

3) Select Time by using the UP or DOWN LEVEL keys and press

ENTER.

4) Select Weight by using the UP or DOWN LEVEL keys and press

ENTER.

5) Press GO, then the display will read 3, 2, 1, Begin and then the program will start.

CHAPTER 4: CONSOLE OVERLAY AND WORKOUT DESCRIPTION

4.5 WORKOUT SETUP STEPS - FITNESS TEST

FITNESS TEST

-The Cooper Fitness Test measures cardiovascular fitness and proves an estimated sub-maximal VO2 result. It is based on power output according to ACSM standards and was developed by the Cooper Institute© (www.cooperinstitute.org). User RPMs must remain between 60-80 RPM during the test. The test will end when the user can no longer maintain this speed. Use of a heart rate strap is optional but provides more data.

The test starts at a low intensity level and gradually increases in intensity (difficulty) every 2 minutes. As it increases, the user must maintain

60-80 RPM to advance to the next level. The test could take upwards of 30+ minutes for very fit individuals. Once the test ends a recovery period (cool down) will begin and the user's results are calculated and displayed. Results are based on the number of stages completed.

Incline will not be adjustable during the test.

1) Start pedaling and press the FITNESS TEST key. Then press ENTER.

2) Select Age by using the UP or DOWN LEVEL keys and press ENTER.

3) Select Gender by using the UP or DOWN LEVEL keys and press ENTER.

4) Select Weight by using the UP or DOWN LEVEL keys and press ENTER.

5) Press GO, then the display will read 3, 2, 1, Begin and then the program will start.

6) Once the workout is complete, the display will read the results of the Fitness Test.

STAGES COMPLETED:

1 Well Below Average

2 Well Below Average

3 Below Average

4 Below Average

5 Average

6 Average

7 Above Average

8 Above Average

9+ Well Above Average

9

10

CHAPTER 4: CONSOLE OVERLAY AND WORKOUT DESCRIPTION

4.6 WORKOUT SETUP STEPS - TARGET HEART RATE

TARGET HEART RATE

- The Matrix R5x-04 Bike comes with standard digital contact heart rate sensors and are POLAR telemetry compatible. The heart rate control workout mode allows the user to program their desired heart rate zone, and the bike will automatically adjust the level based upon the user's heart rate. The heart rate zone is calculated using the following equation: (220-Age)8%=target heart rate zone. The user must wear a POLAR telemetric strap or continually hold onto the contact heart rate grips for this workout.

Locate the metal sensors on the handlebars of the bike. Notice that there are two separate pieces of metal on each grip. You must be making contact with both pieces of each grip to get an accurate heart rate reading. You can grab these sensors in any program to view your current heart rate.

1) Start pedaling and press the HEART RATE key. Then press

ENTER.

2) Select Age by using the UP or DOWN LEVEL keys and press

SELECT.

3) Select Target HR Percentage by using the UP or DOWN LEVEL keys and press SELECT.

4) Select Time by using the UP or DOWN LEVEL keys and press

SELECT.

5) Select Weight by using the UP or DOWN LEVEL keys and press

SELECT.

6) Press GO, then the display will read 3, 2, 1, Begin and the program will start.

4.7 WORKOUT SETUP STEPS - CONSTANT WATTS

CONSTANT WATTS

- Constant Watts is a unique program that allows you to vary your cadence or RPM and the bike's resistance level will adjust accordingly to your selected goal. The quicker you pedal, the less resistance for the goal selected.

1) Start pedaling and press the CONSTANT WATTS key. Then press ENTER.

2) Select Watts by using the UP or DOWN LEVEL keys and press

SELECT.

3) Select Time by using the UP or DOWN LEVEL keys and press

SELECT.

4) Select Weight by using the UP or DOWN LEVEL keys and press SELECT.

5) Press GO, then the display will read 3, 2, 1, Begin and the program will start.

CHAPTER 5: MANAGER MODE

5.1 MANAGER MODE OVERVIEW

The Manager's Custom Mode allows the club owner to customize the bike for the club.

1) To enter Manager Mode, press and hold down the UP and DOWN LEVEL keys. Continue to hold down these two keys until the display reads Manager Mode and hit ENTER (Figure A).

2) To scroll through the list of options in Manager Mode, use the UP and DOWN LEVEL keys. Each of the custom settings will show on the display.

3) To select a custom setting, press the ENTER key when the desired setting is shown.

4) To change the value of the setting, use the UP and DOWN LEVEL keys.

5) To confirm and save the value of the setting, press the ENTER key.

6) To exit the setting without saving, press the BACK key.

7) Press and hold the STOP key for 3-5 seconds to return to normal operation.

5.2 MANAGER MODE OVERVIEW

CUSTOM SETTING

Maximum Time

Default Time

DEFAULT

60 min

30 min

Default Level

Default Age

Default User Weight

Accumulated Distance

Accumulated Time

Software Version

Timer Mode

Speed / Distance Mode

Out of Order

Gender

Language

Sound Mode

1

30

150 lbs /

75 kg

N/A

N/A

N/A

Up

Mile

Off

Male

English

On

MINIMUM

5 min

5 min

1

10

80 lbs / 36 kg

0

0

N/A

Up

Mile

On

Male

English

On

MAXIMUM DESCRIPTION

99 min Sets the total run time of any program.

Maximum

Time

Setting

30

Workout time when GO is pressed or when no time is selected during program set up.

100

Starting resistance when GO is pressed or when no resistance is selected during program set up.

Starting age when GO is pressed or when no age is selected during program set up.

Weight used for program calorie expenditure calculations. 400 lbs /

182 kg

999,999

Miles

Total distance for all programs.

999,999 hours

N/A

Down

Kilometer

Off

Female

Total time for all programs displayed in hours.

Current software version of UCB / LCB.

Determines whether the timer counts up or down.

Displays distance in miles or kilometers.

Locks the machine when out of order.

English

Off

Determines the gender of the user when not selected during program set up.

Sets the language for the console. Select between English, Spanish,

German, French, Italian, Dutch and Turkish.

Turns the chime on / off when a button is pressed.

11

12

CHAPTER 6: ENGINEERING MODE

6.1 USING ENGINEERING MODE

To enter Engineering Mode, hold the LEVEL UP and DOWN keys for 3-5 seconds until Manager Mode appears on the middle LED display.

Press the LEVEL UP or DOWN key to scroll to Engineering Mode. Press ENTER to go into Engineering Mode.

CODE

Disable Errors

Speed Units

Machine Type

Club ID

ErP Mode (Sleep

Time)

Audio Source

AM System

Volume Control

DEFAULT OPTIONS

No Yes or No

Mile

R5x-05

Power Save Time 30 Seconds

Pause Time 30 Seconds

Serial Number N/A

N/A

Off

Off

WIFI

TV/ PCTV:

Output:13

REMOTE TV

Output:13

REMOTE TV

Input:15

DESCRIPTION

No - Shows A-C class error codes. Yes - Shows only C class error codes.

Mile or Kilometer

H5x-05, U5x-05,

R5x-05, H5x-04,

U5x-04, R5x-04,

E5x-02, E5x-03

Set for Mile or Kilometer.

The Hybrid bike console should be set to U5x-05.

30-60 Seconds Power saving time for the self powered frame.

15 - 120 Seconds For non self powered frames only. Not used on this model.

N/A Serial Number input is available for both the Console and Frame. Use the number keys and UP / DOWN LEVEL keys to enter Engineering Mode. Due to the limited

LED characters, 2 layers are used to enter the serial number. First Layer:

- PPPPP V

- PPPPP is the product name.

- V is the version. If the version is A, just leave this blank.

Second Layer

- YY MM nnnnn.

- YY is the year (11, 12).

- MM is the month (e.g. 08, 09, 10).

- nnnnn is the actual serial number.

Use the UP / DOWN LEVEL keys to navigate the layers and the number keys to input the serial number. The product name is dependent on the Machine Type setting.

For example, the console is EP612 with version A and the manufactured date is

2012.08 with 98765. The frame is RB307 and the manufactured date is 2013.06 with 12345. Their serial numbers are:

Console SN: EP612 1st layer, 120898765 2nd layer.

Frame SN: RB307 1st layer, 130612345 2nd layer.

N/A

Off or On (1-30

Minutes)

This sets the club ID for clubs using Asset Management.

If there is no use of the machine over a period of time, the console LEDs will turn off (go into ErP mode).

Off / TV / PC TV /

Remote TV

WIFI / RF Radio

1~ 32

1~ 32

Manual setting that sets which outside TV will have audio through the console audio ports.

To select AM output device by WIFI or RF Radio.

Controls the default TV volume for entertainment wired through the C-Safe port.

a. Input Default (DF : 15 / Range : 1 ~ 15) b. Max Default (DF : 32 / Range : 1 ~ 32) c. Output Default (DF : 13 / Range : 1 ~ Max)

Remote TV support a / b / c item. TV and PCTV only support c item.

1~ 15

CHAPTER 7: SERVICE MODE

7.1 USING SERVICE MODE

To enter Service Mode, hold the LEVEL UP and DOWN keys for 3-5 seconds until Manager Mode appears on the middle LED display. Press the LEVEL UP or DOWN key to scroll to Service Mode. Press ENTER to go into Service Mode.

CODE

Service 1

Service 2

Service 3

DEFAULT

Display Test

Keypad Test

Distance / Time

OPTIONS

Distance:

Mile 0 - 99999

Kilometer 0 - 160898

Time:

0 - 999999

DESCRIPTION

Press the ENTER key repeatedly to check each set of LEDs on the display sequentially.

Press any key and the display should show the corresponding message.

Manually sets the Accumulated

Distance and Time.

Service 4

Service 5

Service 6

Service 7

Service 8

CSafe / RF Test

Error Log

Set Date / Time

Export and Import Parameter

WiFi Function

Press the ENTER key to test

CSAFE. Press the ENTER key again to test the RF.

Shows the last 10 errors. Press and LEVEL UP and DOWN for 3 seconds to clear the errors.

Press the LEVEL keys to move cursor, the number keys to set date / time, and the ENTER key to save.

Export Parameter - Export all parameters to a USB device.

Import Parameter 1 - Imports the engineer parameters to a USB device except serial number, accumulated distance and time.

Import Parameter 2 - Imports the engineer parameters to a USB device.

Automatically detects the available IP address and displays it.

13

14

8.1 ELECTRICAL DIAGRAMS

CHAPTER 8: TROUBLESHOOTING

CHAPTER 8: TROUBLESHOOTING

8.1 ELECTRICAL DIAGRAMS

- CONTINUED

15

16

CHAPTER 8: TROUBLESHOOTING

8.1 ELECTRICAL DIAGRAMS - CONTINUED

MCB POWER WIRE

DIGITAL COMMUNICATION WIRE

CHAPTER 8: TROUBLESHOOTING

8.1 ELECTRICAL DIAGRAMS - CONTINUED

PULSE SENSOR WIRE

17

CHAPTER 8: TROUBLESHOOTING

8.1 ELECTRICAL DIAGRAMS - CONTINUED

PULSE EXTENDED WIRE

18

RAIL CONNECT WIRE

8.2 LCB LED INDICATORS

CHAPTER 8: TROUBLESHOOTING

19

20

CHAPTER 8: TROUBLESHOOTING

8.3 TROUBLESHOOTING - ERROR 04A0 / 0440

ERROR CODE 04A0 / 0440

1) SYMPTOM:

04A0 – UCB communication disconnected.

0440 – Timeout receive packet (LCB can not receive any data for 50 seconds).

2) SOLUTION:

If the display is giving a 04A0 error, check the LCB LED10 status.

- LED10 blinking: Turn off power and after 3 seconds, turn on power again. If console also show the 04A0, re-install UCB software again. If this does not resolve the issue, replace the UCB.

- LED10 off: Check the connection of the digital communication wire at the UCB and LCB (Figures A & B). If the connection is good, replace the digital communication wire.

- If replacing the UCB and digital communication wire does not work, replace the LCB.

FIGURE A FIGURE B

CHAPTER 8: TROUBLESHOOTING

8.4 TROUBLESHOOTING - ERROR 04B0

ERROR CODE 04B0

1) SYMPTOM:

04B0 – LCB communication disconnected.

2) SOLUTION:

1) If the display is giving a 04B0 error, check the LCB LED10 status.

- LED10 blinking: Turn off power and after 3 seconds, turn on power again. If the console shows the 04A0 error, skip to Step 2.

- LED10 off: Check the connection of the digital communication wire at the UCB and LCB (Figure A & B). If the connection is good, replace the digital communication wire.

2) If LEDs 7 / 8 / 9 / 10 blinking together, this should be LCB software problem. Re-install LCB software. If this does not resolve the issue, replace the LCB.

FIGURE A FIGURE B

21

22

8.5 TROUBLESHOOTING - ERROR 0248

CHAPTER 8: TROUBLESHOOTING

ERROR CODE 0248

1) SYMPTOM:

0248 - Battery disconnection or fail. (When power is on, LCB battery voltage is less than 6 VAC).

2) SOLUTION:

1) Please check the battery wire connection between the battery and LCB (Figure A).

2) Check the battery voltage (Figure B), if it is less than 6 V, please plug in the power cord to charge battery for 1 hour. Replace the battery if it will not hold a charge.

3) If the battery voltage is more than 6 V, replace the LCB.

FIGURE A FIGURE B

CHAPTER 8: TROUBLESHOOTING

8.6 TROUBLESHOOTING - ERROR 0247

ERROR CODE 0247

1) SYMPTOM:

0247 - MCU fail.

2) SOLUTION:

1) Replace LCB.

8.7 TROUBLESHOOTING - ERROR 02B4 / 03A8 / 02AB / 0441

ERROR CODE 02B4 / 03A8 / 02AB / 0441

1) SYMPTOM:

02B4 – Resistance type error.

03A8 – Control settings on the machine does not match the model setting.

02AB – Machine Type Error.

0441 – Correct packet but LCB without the function (LCB does not support this command).

2) SOLUTION:

1) Check the machine type is matched with the correct frame in Service mode (Figure A).

2) Check if the console is matched with the correct frame.

3) Replace the LCB.

4) Replace the UCB.

FIGURE A

23

24

CHAPTER 8: TROUBLESHOOTING

8.8 TROUBLESHOOTING - ERROR 0149 / 01AF

ERROR CODE 0149 / 01AF

1) SYMPTOM:

0149 – Electro-magnet over current.

01AF – Electro-magnet disconnected.

2) SOLUTION:

1) Check if the Electro-magnet is short circuited or open (Figure A).

- If the resistance data shows a short / open ohms or is outside the range of 12.8 ~14.2 ohms, replace the Electro-magnet.

- If the resistance data is in the range between 12.8 ~14.2 ohms, replace the LCB.

FIGURE A

CHAPTER 8: TROUBLESHOOTING

8.9 TROUBLESHOOTING - ERROR 01B4

ERROR CODE 01B4

1) SYMPTOM:

01B4 – Battery connection reverse protection.

2) SOLUTION:

1) Check the battery wire connection between the battery and LCB (Figure A).

2) Check the battery voltage (Figure B).

- If there is no data on voltage, replace the battery

- If there is data on voltage, replace the LCB

FIGURE A FIGURE B

25

26

CHAPTER 8: TROUBLESHOOTING

8.10 TROUBLESHOOTING - NO RESISTANCE ISSUES

NO RESISTANCE ISSUES

1) SYMPTOM:

No resistance.

2) SOLUTION:

1) Check the resistance wire connection between the ECB and LCB (Figure A).

2) Check if the resistance is open (Figure B).

- If there is no data on resistance, replace the ECB.

- If there is data on resistance, replace the LCB.

CHAPTER 8: TROUBLESHOOTING

8.11 TROUBLESHOOTING - HEART RATE ISSUES

HEART RATE FUNCTION DOES NOT WORK OR IS READING INCORRECTLY

POSSIBLE CAUSES:

1) The HR grips are not hooked up correctly.

2) The HR grip wiring is damaged.

3) The console or HR board is not properly grounded.

4) The console, HR board, or wiring between are bad.

SOLUTION:

1) Perform a DC Voltage test on the HR grips.

a. With one prong of a multi meter on each of the plates on one side of the HR grip set (Figure A), a voltage reading of between .5 and 2.0 should be seen. If the reading is correct, the issue is not with the HR grips or grip wiring.

b. If the reading is not correct, remove the screws holding the halves of the HR grip together and check the connection of the wiring to the grips (Figure B).

2) Remove the console from the unit and verify continuity of the HR grip wiring. With a multi meter set for ohms, place one prong on the HR grip wiring coming up the console mast (Figure C), and the other on the appropriate plate.

a. An ohm reading of less than 1 should be received. If it is higher, replace the HR grip wiring.

3) Perform a continuity check on the console (See Service Bulletin - Continuity Test on Matrix Bikes).

a. Once the console continuity is confirmed, perform a continuity check on the HR board ground wire. With a multi meter set for ohms, place one prong on the HR board ground wire (Figure D), and the other on the console ground wire. An ohm reading of less than 1 should be received.

If it is higher, replace the HR board.

4) If all the troubleshooting listed above has been performed, and the unit still has HR issues, replace the HR board.

a. If the HR board does not resolve the issue, replace the console.

FIGURE A FIGURE B

FIGURE C FIGURE D

27

28

CHAPTER 8: TROUBLESHOOTING

8.12 TROUBLESHOOTING - NO POWER TO THE CONSOLE

POWER SWITCH IS ON, BUT THE CONSOLE HAS NO DISPLAY

POSSIBLE CAUSES:

1) The unit is not getting power from the outlet.

2) The LCB is not getting power from the power receptacle.

3 & 4) The LCB LEDs are lit, but there is no power to the console.

SOLUTION:

1) Verify power at the outlet. If the outlet is not outputting 120VAC, check the fitness room power.

2) Remove the front disk and check to see if LED1 is lit on the LCB (Figure A).

a. If it is not lit, verify power at the outlet. if the outlet is not outputting 120V power, check the fitness room power.

b. If LED9 is still not lit, check the incoming AC power to the LCB. If the incoming power is not correct, replace the power cord.

c. Replace the LCB if all power components are OK and there are AC volts to the LCB.

3 & 4) Remove the front disk and check to see if LED1 is lit on the LCB.

a. If LED9 is lit, check the connection of the console cable.

b. If the console cable is connected properly, LED2 on the control board should be lit (Figure B). If it is not lit, check voltage on the console cable. Measure voltage across pins 1 and 3 of the cable, it should show around 12V. Replace the console cable if this reading is off.

c. If LED2 on the control board is lit, but there is still no power to the console, replace the console.

FIGURE A FIGURE B

CHAPTER 8: TROUBLESHOOTING

8.13 TROUBLESHOOTING - KEYPAD ISSUES

ALL OR SOME OF THE FUNCTION KEYS DO NOT RESPOND

POSSIBLE CAUSES:

1) The keypad connection ribbon cable has not been plugged in correctly.

2) The keypad is damaged.

3) The UCB is damaged.

SOLUTION:

1) Perform a keypad test in Service Mode:

a. Press and hold both the UP and DOWN LEVEL keys until Manager Mode appears on the display.

b. Use the UP and DOWN LEVEL keys to scroll to Service Mode 2 and press ENTER.

c. Test the affected keypad. If the keypad works in the keypad test it may not be a functioning key in the program used for testing it.

2) Check the connections of the keypad at the UCB.

a. Remove the console from the console mast.

b. Remove the 6 screws holding the back of the console to the front (Figure A).

c. Inspect the keypad ribbon cable connection at the UCB (Figure B).

d. Even if the keypad ribbon cable appears to be connected correctly, unplug and re-seat the cable.

3) Replace the affected keypad.

4) Replace the console.

FIGURE A FIGURE B

29

30

CHAPTER 9: PART REPLACEMENT GUIDE

9.1 CONSOLE REPLACEMENT

1) Remove the 4 screws holding the console to the frame (Figure A).

FIGURE A

2) Disconnect the console cable and HR connections from the defective console and remove the console (Figure B).

FIGURE B

3) Reinstall the wire connections to the new console.

4) Carefully push the wires into the console and mast until they are clear of the console / mast connection and attach the console to the mast using the 4 screws.

5) Test the bike for function as outlined in Section 9.24.

CHAPTER 9: PART REPLACEMENT GUIDE

9.2 HANDLEBAR REPLACEMENT

1) Remove the 4 screws holding the heart rate handlebar to the console mast being careful to support the handlebar (Figure A).

2) Carefully pull the wires from the console mast until the connectors are showing, and then disconnect the 2 wires from the handlebar and remove the defective handlebar (Figure B).

FIGURE A

3) Reverse Steps 1-2 to install a new handlebar.

4) Test the bike for function as outlined in Section 9.24.

FIGURE B

31

32

CHAPTER 9: PART REPLACEMENT GUIDE

9.3 CUP HOLDER REPLACEMENT

1) Remove the 2 screws holding the cup holder to the frame (Figure A).

2) Remove the cup holder (Figure B).

FIGURE A

3) Reverse Steps 1-2 to install a new cup holder.

FIGURE B

CHAPTER 9: PART REPLACEMENT GUIDE

9.4 KEYPAD / OVERLAY REPLACEMENT

NOTE: The instructions below are for console overlays / keypads replacement, but the procedure is the same regardless of where the overlay / keypad is.

1) Turn off power and disconnect the cord from the machine.

2) Remove the console as outlined in Section 9.1.

3) Remove the back cover of the console (Figure A).

4) Unplug and remove the faulty overlay (Figure B).

FIGURE A

5) Clean the console area with alcohol to remove any left over adhesive (Figure C).

6) Remove the protective film over the display window of the overlay (Figure D).

FIGURE B

FIGURE C FIGURE D

33

CHAPTER 9: PART REPLACEMENT GUIDE

9.4 KEYPAD / OVERLAY REPLACEMENT - CONTINUED

7) Peel part of the protective film from the back of the overlay (Figure E).

8) Push the overlay ribbon cable through the hole in the console and plug it in (Figure F).

FIGURE E FIGURE F

9) Match the overlay to the cutout on the console (Figure G).

10) Press down on the corners of the overlay to keep it in place, then remove the protective film (Figure H & I).

11) Once the overlay is in the correct position, press down on the overlay with a cloth to adhere it to the console plastic (Figure J).

FIGURE G FIGURE H

34

FIGURE I FIGURE J

12) Use the same procedure to replace any additional faulty overlays. NOTE: Overlays can not be reused.

13) Test the bike for function as outlined in Section 9.24.

CHAPTER 9: PART REPLACEMENT GUIDE

9.5 SEAT PAD REPLACEMENT

1) Remove the 4 screws holding the seat pad to the seat frame (Figure A).

2) Lift the seat pad away from the seat frame (Figure B).

FIGURE A

3) Reverse Steps 1-2 to install a new seat pad.

FIGURE B

35

36

CHAPTER 9: PART REPLACEMENT GUIDE

9.6 BACK PAD REPLACEMENT

1) Remove the 2 bolts holding the back pad to the seat frame (Figure A).

2) Remove the back pad (Figure B).

FIGURE A

3) Reverse Steps 1-2 to install a new back pad.

FIGURE B

CHAPTER 9: PART REPLACEMENT GUIDE

9.7 HEART RATE GRIPS REPLACEMENT

1) Remove the 3 screws holding the HR grip together (Figure A).

2) Once the 3 screws are removed, the HR grip can be split into 2 pieces (Figure B).

FIGURE A FIGURE B

3) Disconnect the keypad / overlay and the HR plate wiring and remove the old HR grip (Figure C).

4) Reverse Steps 1-3 to install new HR grips. The white wire should be on the back side HR plate, the red wire on the front (Figure D).

FIGURE C

5) Test the Bike for function as outlined in Section 9.24.

FIGURE D

37

38

CHAPTER 9: PART REPLACEMENT GUIDE

9.8 SEAT SET REPLACEMENT

1) Remove the cup holder as outlined in Section 9.3.

2) Remove the seat pad as outlined in Section 9.5.

3) Remove the back pad as outlined in Section 9.6.

4) Remove the HR grips as outlined in Section 9.7.

5) Disconnect the heart rate wiring (Figure A).

6) Remove the 4 screws holding the seat set to the seat slide set (Figure B).

FIGURE A

7) Remove the upper seat set from the seat slide set (Figure C).

FIGURE B

8) Reverse Steps 1-7 to install a new seat set.

9) Test the bike for function as outlined in Section 9.24.

FIGURE C

CHAPTER 9: PART REPLACEMENT GUIDE

9.9 SEAT SLIDE SET REPLACEMENT

1) Remove the seat set as outlined in Section 9.8.

2) Remove the 2 screws holding the end cap over to the guide rail set (Figure A).

3) Remove the end cap cover (Figure B).

FIGURE A

4) Remove the 2 screws holding the adjust plate to the adjustable plate (Figure C).

5) Remove the adjust plate (Figure D).

FIGURE B

FIGURE C FIGURE D

39

40

CHAPTER 9: PART REPLACEMENT GUIDE

9.9 SEAT SLIDE SET REPLACEMENT - CONTINUED

6) Remove the 2 screws holding the indicate cap to the seat slide set (Figure E).

7) Remove the indicate cap (Figure F).

FIGURE E

8) Cut the cable tie and disconnect the HR wire from seat slide set (Figure G).

9) Depress the seat position lever and pull off the seat slide set from the guide rail set (Figure H).

FIGURE F

FIGURE G

10) Reverse Steps 1-9 to install a new seat slide set.

11) Test the bike for function as outlined in Section 9.24.

FIGURE H

CHAPTER 9: PART REPLACEMENT GUIDE

9.10 REAR COVERS REPLACEMENT

1) Remove the 4 screws holding the left side rear cover to the frame and remove it (Figure A).

2) Remove the 4 screws holding the right side rear cover to the frame and remove it (Figure B).

FIGURE A

3) Figure C shows the bike with both rear side covers removed.

FIGURE B

4) Reverse Steps 1-2 to install new rear side cover.

FIGURE C

41

CHAPTER 9: PART REPLACEMENT GUIDE

9.11 GUIDE RAIL SET REPLACEMENT

1) Remove the seat slide set. as outlined in Section 9.9.

2) Remove the rear covers as outlined in Section 9.10.

3) Cut the cable tie and disconnect the HR wire from guide rail set (Figure A).

4) Use a 13 mm wrench to remove the 6 screws holding the guide rail set to the frame (Figure B)

FIGURE A

5) Pull the HR wires out of the guide rail set and remove the guide rail set (Figure C).

FIGURE B

42

FIGURE C

6) Reverse Steps 1-5 to install a new guide rail set. NOTE: When installing a new guide rail set, be sure to pull the HR wire up through the new guide rail prior to installing the 6 screws into the frame.

7) Test the bike for function as outlined in Section 9.24.

CHAPTER 9: PART REPLACEMENT GUIDE

9.12 PEDAL REPLACEMENT

1) Use a 15 mm commercial pedal wrench to remove the pedal from the crank (Figure A). NOTE: For the right side pedal, the threads are normal. For the left side pedal, the threads are reversed (the pedal turns off counterclockwise).

2) Remove the pedal (Figure B).

FIGURE A

FIGURE B

3) Reverse Steps 1-2 to install a new pedal. NOTE: Be sure to tighten the pedal as much as possible onto the crank with a commercial pedal wrench (available from Matrix - part # ZMS4001254).

43

44

CHAPTER 9: PART REPLACEMENT GUIDE

9.13 CRANK AXLE SET REPLACEMENT

1) Remove the bolt that holds the crank to the drive axle set (Figures A & B).

FIGURE B FIGURE A

2) The crank can be removed (Figure C).

FIGURE C

3) Reverse Steps 1-2 to install a new crank axle set. NOTE: Torque the bolt removed in Step 1 to 80 N-m / 800 kgf-cm.

4) Test the bike as outlined in Section 9.24.

CHAPTER 9: PART REPLACEMENT GUIDE

9.14 FRONT SHROUDS REPLACEMENT

1) Remove the 4 screws that hold the silver cover to the frame (Figure A).

2) Remove the silver cover (Figure B).

FIGURE A

3) Remove the 2 screws that hold the grey cover to the frame (Figure C).

4) Remove the grey cover (Figure D).

FIGURE B

FIGURE C

5) Reverse Steps 1-4 to install new shrouds.

6) Test the bike for function as outlined in Section 9.24.

FIGURE D

45

CHAPTER 9: PART REPLACEMENT GUIDE

9.15 FRONT COVERS REPLACEMENT

1) Remove the pedals as outlined in Section 9.12.

2) Remove the crank as outlined in Section 9.13.

3) Remove the front shrouds as outlined in Section 9.14.

4) Remove the 6 screws to detach the front covers from the frame (Figures A & B).

FIGURE A

5) Figure C shows both the front covers removed.

FIGURE B

46

6) Reverse Steps 1-5 to install new front covers.

FIGURE C

CHAPTER 9: PART REPLACEMENT GUIDE

9.16 CONSOLE MAST REMOVAL

1) Remove the console as outlined in Section 9.1.

2) Remove the handlebars as outlined in Section 9.2.

3) Remove the front shrouds as outlined in Section 9.14.

4) Remove the 4 screws holding the console mast to the frame (Figure A)

FIGURE A

5) Pull the wires out the bottom of the console mast and remove the mast (Figure B).

FIGURE B

6) Reverse Steps 1-5 to install a new console mast. NOTE: When installing a new console mast, be sure to pull the console wires up through the new mast prior to installing the 4 screws into the frame.

7) Test the bike for function as outlined in Section 9.24.

47

CHAPTER 9: PART REPLACEMENT GUIDE

9.17 LOWER CONTROL BOARD REPLACEMENT

1) Remove the left side front cover as outlined in Section 9.15.

2) Disconnect the 5 wire connections to the lower board (Figure A).

3) Remove the 2 screws holding the lower control board to the frame (Figure B), and remove the lower control board.

48

FIGURE A FIGURE B

4) Reverse Steps 1-3 to install a new lower board. Figure C shows the electrical connections to the lower board.

2 Pin Connector from the Battery

8 Pin Connector from the Console

6 Pin Connector from the DC power source

2 Pin Connector from the ECB

3 Pin Connector from the Generator

5) Test the bike for function as outlined in Section 9.24.

FIGURE C

CHAPTER 9: PART REPLACEMENT GUIDE

9.18 BATTERY REPLACEMENT

1) Remove the right side pedal as outlined in Section 9.12.

2) Remove the right side crank as outlined in Section 9.13.

3) Remove the right side front cover as outlined in Section 9.15 (Figure A).

4) Disconnect the 2 wires from the battery (Figure B).

FIGURE A

5) Disconnect the 2 cable ties from the battery bracket (Figure C).

6) Remove the battery (Figure D).

FIGURE B

FIGURE C

7) Reverse Steps 1-6 to install a new battery.

FIGURE D

49

CHAPTER 9: PART REPLACEMENT GUIDE

9.19 DRIVE BELT REPLACEMENT

1) Remove the right side pedal as outlined in Section 9.12.

2) Remove the right side crank as outlined in Section 9.13.

3) Remove the right side front cover as outlined in Section 9.15 (Figure A).

4) Using a hook or loop of wire, remove the spring from the frame (Figure B). The tensioner should now pivot away from the drive belt.

FIGURE A FIGURE B

5) Remove the drive belt (Figure C).

6) Use a straight edge to make sure that the pulley and generator pulley are in a straight line (Figure D). If the belt is not on line, try to adjust the generator location.

50

FIGURE C FIGURE D

7) Reverse Steps 1-6 to install a new drive belt. NOTE: Be sure to reattach the tension spring. Rotate the pulley to make sure that the motion is smooth and that there is no wobbling to one side.

CHAPTER 9: PART REPLACEMENT GUIDE

9.20 GENERATOR REPLACEMENT

1) Remove the pedals as outlined in Section 9.12.

2) Remove the cranks as outlined in Section 9.13.

3) Remove the front covers as outlined in Section 9.15.

4) Remove the drive belt as outlined in Section 9.19.

5) Cut the cable tie and disconnect the generator with ECB wire from the LCB (Figures A & B).

FIGURE A FIGURE B

6) Remove the 4 screws holding the generator to the frame (Figures C & D), and remove the generator.

FIGURE C

7) Reverse Steps 1-6 to install a new generator.

8) Test the bike for function as outlined in Section 9.24.

FIGURE D

51

CHAPTER 9: PART REPLACEMENT GUIDE

9.21 REAR STABILIZER REPLACEMENT

1) Remove the 2 screws holding the black cover to the rear stabilizer (Figure A).

2) Remove the black cover (Figure B).

FIGURE A

3) Remove the 4 screws holding the rear stabilizer to the frame (Figure C).

4) Remove the rear stabilizer (Figure D).

FIGURE B

52

FIGURE C FIGURE D

5) Reverse Steps 1-4 to install a new rear stabilizer. NOTE: When installing a new rear stabilizer, be sure to make sure that the leveling is stable as outlined in Section 10.4.

CHAPTER 9: PART REPLACEMENT GUIDE

9.22 FRONT STABILIZER REPLACEMENT

1) Remove the 4 screws holding the rear stabilizer to the frame (Figures A & B). .

FIGURE B FIGURE A

2) Remove the front stabilizer (Figure C).

3) Reverse Steps 1-2 to install a new front stabilizer.

FIGURE C

53

CHAPTER 9: PART REPLACEMENT GUIDE

9.23 DRIVE AXLE SET REPLACEMENT

NOTE: A Matrix special tool is needed to correctly replace a drive axle. Order part

# 1000323981

from Matrix CTS at 866-693-4863 ext 3.

1) Turn off the power and disconnect the cord from the machine.

2) Remove the front covers from the machine as outlined in Section 9.15.

3) Remove drive belt as outlined in Sections 9.19.

4) On the left side of the frame, remove the retainer clip that holds the drive axle bearings in the frame (Figure A).

5) Use a hammer to hit the screw until the drive axle assembly is loose in the frame, and remove it (Figure B).

FIGURE A FIGURE B

6) Install the tool into the hole in the frame and use a rubber mallet to hit the end of the tool until the bearing can be removed from the frame

(Figures C & D).

FIGURE C

7) The drive axle should have come with an iron plate installed (Figure E).

8) Assemble the Matrix tool as shown in Figure F.

FIGURE D

54

FIGURE E FIGURE F

CHAPTER 9: PART REPLACEMENT GUIDE

9.23 DRIVE AXLE SET REPLACEMENT - CONTINUED

9) Slide the drive axle assembly into the frame from the right side. Install the bearing cap portion of the tool into the left side of the frame (Figure

G).

10) Mount the other tool from Figure F behind the bearing cap portion of the tool. Use the M10 x 100L x 1.25P screw with a nut to attach the tool to the drive axle (Figure H).

FIGURE G

11) Turn the screw until it is close into the drive axle (Figure I).

12) Then turn the nut until it is close to the cup portion of the tool (Figure J).

FIGURE H

FIGURE I

13) Use a wrench to hold the screw, then turn the nut to pull the drive axle into the frame (Figure K).

14) Turn the nut until the iron plate is close to the frame on the right side (Figure L).

FIGURE J

FIGURE K FIGURE L

55

CHAPTER 9: PART REPLACEMENT GUIDE

9.23 DRIVE AXLE SET REPLACEMENT - CONTINUED

15) Remove the tools, then insert the bearing into the hole in the frame on the left side (Figure M).

16) Again use the M10 x 100L x 1.25P screw with a nut to attach the tool to the drive axle (Figure N).

FIGURE M

17) Turn the screw until it is close into the drive axle (Figure O).

18) Then turn the nut until it is close to the cup portion of the tool (Figure P).

FIGURE N

56

FIGURE O FIGURE P

19) Use a wrench to hold the screw, then turn the nut to push the bearing into the hole in the frame (Figure Q).

20) Insert the retainer clip to hold the bearing in the frame (Figure R).

FIGURE Q FIGURE R

CHAPTER 9: PART REPLACEMENT GUIDE

9.23 DRIVE AXLE SET REPLACEMENT - CONTINUED

21) Use a screwdriver to remove the iron plate from the drive axle (Figures S & T).

FIGURE S FIGURE T

22) Rotate the drive axle to make sure that the motion is smooth and that there is no wobbling to one side (Figures U).

23) Re-install the belts as outlined in Section 9.19.

24) Reverse Steps 1-2 to re-assemble the unit.

25) Test the Bike as outlined in Section 9.24.

FIGURE U

57

58

CHAPTER 9: PART REPLACEMENT GUIDE

9.24 TESTING THE BIKE

ONCE THE UNIT OR REPLACEMENT PART IS FULLY INSTALLED AND ASSEMBLED AND

PROPERLY PLACED ON THE FLOOR, USE THE FOLLOWING INSTRUCTIONS TO SETUP

AND TEST THE MACHINE:

1) Check that the console is set for recumbent bike.

a. Press and hold both LEVEL keys until Manager Mode appears on the display.

b. Press the UP or DOWN LEVEL keys until Engineering Mode appears on the display.

c. Use the UP or DOWN LEVEL keys to scroll to Machine Type.

d. Press ENTER on Machine Type and make sure it is set for R5x-05.

e. If Machine Type is not set for R5x-05, change to R5x-05 using the UP or DOWN LEVEL key and press ENTER to save.

f. Press and hold the STOP key for 3-5 seconds to return to normal function.

2) If the unit has an add on TV, program the TV channels (see Entertainment Owner's Manual).

3) If the unit is a installed as part of a new installation or if a battery was replaced, charge the battery.

4) Without hitting start or entering any program modes, sit on the bike and hold the handlebars while pedaling to simulate exercising. While moving, listen for any odd noises or squeaks.

5) After stopping movement, press the green GO key and begin pedaling.

6) Grasp the hand grips to check for proper heart rate response.

7) Press the level up and down buttons on the console and hand grips to make sure resistance is fully functional.

8) Move the seat forward and back to check for excessive play or difficulty moving the seat.

9) If everything functions properly, stop pedaling and the unit will reset to normal operation within 30 seconds.

CHAPTER 10: BIKE SPECIFICATIONS AND ASSEMBLY GUIDE

10.1 R5x-05 BIKE SPECIFICATIONS

FEATURES

CONTACT & TELEMETRIC HR

SENSORS

R5x RECUMBENT

YES

HANDLEBAR DESIGN

SEAT SIDE AND FRONT VERTICAL ERGO

BEND

INTEGRATED ARM RESTS

THUMB SWITCH CONTROLS

RESISTANCE SYSTEM

TECHNOLOGY

YES

YES

POWER REQUIREMENTS

MINIMUM WATTS

MINIMUM RPM

CONSOLE

JID BRUSHLESS GENERATOR

SELF POWERED - POWERED 100-125 V, 60

HZ OR 216-250 V, 50 HZ

N/A

YES

DISPLAY TYPE

DISPLAY FEEDBACK

USER DEFINED MULTI-LANGUAGE

DISPLAY

RESISTANCE LEVELS

WORKOUTS

DOT-MATRIX LED

TIME ELAPSED, TIME REMAINING, TOTAL

PROGRAM TIME, CLOCK, DISTANCE

(KILOMETERS OR MILES), CALORIES,

SPEED, LEVEL, RPM, HEART RATE, METS,

WATTS, STATIC PROFILE DISPLAY

YES - ENGLISH, GERMAN, FRENCH,

ITALIAN, SPANISH, DUTCH, PORTUGUESE,

SWEDISH, FINNISH, JAPANESE

30

MANUAL, ROLLING HILLS, INTERVAL

TRAINING, RANDOM, FAT BURN, FITNESS

TEST, HEART RATE, CONSTANT WATTS

CSAFE READY - FITLINXX™

CERTIFIED

NETPULSE COMPATIBLE

ON-THE-FLY PROGRAM CHANGE

FIT TOUCH TECHNOLOGY™

INTEGRATED VISTA CLEAR™

DIGITAL READY TELEVISION

VIRTUAL ACTIVE™ COMPATIBLE

FITCONNEXION™ READY

WIFI

ETHERNET PORT

WEB CONNECTIVITY

FACILITY COMMUNICATOR

PORTAL/CALENDAR

ASSET MANAGEMENT

COMPATIBLE

NO

YES

YES

NO

NO

NO

YES

YES

YES

NO

NO

YES

IPOD® COMPATIBLE

IPHONE® COMPATIBLE

USB PORT

MULTIMEDIA PLAYBACK

NIKE + IPOD® COMPATIBLE

PERSONAL FAN

TECH SPECS

OVERALL DIMENSIONS

YES - CHARGING ONLY

YES - CHARGING ONLY

YES

NO

NO

YES

L X W X H

CRANK DESIGN

MAXIMUM USER WEIGHT

WEIGHT

63.2" X 28.8" X 54.6"

160.5CM X 73.2CM X 138.8CM

SINGLE PIECE

400 LBS/182 KG

SHIPPING WEIGHT

167 LBS/76 KG

204 LBS/92.6 KG

NORTH AMERICAN SPECIFICATIONS SHOWN. SPECIFICATIONS SUBJECT TO

CHANGE. FOR LATEST SPECIFICATIONS PLEASE VISIT WWW.MATRIXFITNESS.

COM

59

60

CHAPTER 10: BIKE SPECIFICATIONS AND ASSEMBLY GUIDE

10.2 ASSEMBLY INSTRUCTIONS

AFTER THESE ASSEMBLY STEPS ARE COMPLETE, BE SURE TO SETUP AND TEST THE UNIT AS OUTLINED

IN SECTION 9.24.

STEP 1

PART

A

B

YELLOW HARDWARE BAGS

TYPE DESCRIPTION

SOCKET HEAD BOLT M8X25L

FLAT WASHER Φ8.2XΦ16.0X2.0T

QTY

8

8

A

B

C

Open

YELLOW HARDWARE BAGS.

Attach the

FRONT STABILIZER TUBE

(1) to the MAIN FRAME (2) using 4

BOLTS (A) and 2 FLAT WASHERS (B).

Attach the

REAR STABILIZER TUBE (3)

to the

MAIN FRAME (2) using 4 BOLTS

(A) and 2 FLAT WASHERS (B).

CHAPTER 10: BIKE SPECIFICATIONS AND ASSEMBLY GUIDE

10.2 ASSEMBLY INSTRUCTIONS - CONTINUED

STEP 2

PART

C

D

BLACK HARDWARE BAG

TYPE DESCRIPTION

SOCKET HEAD BOLT M8X20L

PHILLIP HEAD BOLT M5X12L

QTY

2

2

A

B

C

Open

BLACK HARDWARE BAG.

Attach the

REAR FRAME HANDLE (3) to

the

MAIN FRAME (2) using 2 BOLTS (C).

Attach the

REAR FRAME COVER (4) to

the

MAIN FRAME (2) using 2 BOLTS (D).

PART

C

E

RED HARDWARE BAGS

TYPE DESCRIPTION

SOCKET HEAD BOLT

TOOTH WASHER

M8X20L

Φ8.5XΦ18.0X2.0T

QTY

4

4

D

E

Carefully pull the

CONSOLE CABLES (5)

through the

CONSOLE MAST (6) using

the twist tie located inside the

CONSOLE

MAST (6).

Attach

CONSOLE MAST (6) to MAIN

FRAME (2) using 4 BOLTS (C) and 4

TOOTH WASHERS (E).

61

62

CHAPTER 10: BIKE SPECIFICATIONS AND ASSEMBLY GUIDE

10.2 ASSEMBLY INSTRUCTIONS - CONTINUED

STEP 3

PART

F

WHITE HARDWARE BAG

TYPE DESCRIPTION

SOCKET HEAD BOLT M8X20L

QTY

4

A Open

GREEN HARDWARE BAG.

B Attach the

CONSOLE HANDLEBARS (7)

to the

CONSOLE MAST (6) using 4 BOLTS

(F).

PART

G

GREEN HARDWARE BAG

TYPE DESCRIPTION

PHILLIPS HEAD BOLT M5X12L

QTY

4

C Open

GREEN HARDWARE BAG.

D Attach the

FRONT SHROUD COVER (8) to

the

MAIN FRAME (2) using 4 BOLTS (G).

CHAPTER 10: BIKE SPECIFICATIONS AND ASSEMBLY GUIDE

10.2 ASSEMBLY INSTRUCTIONS - CONTINUED

STEP 4

PART

H

PINK HARDWARE BAG

TYPE DESCRIPTION

PHILLIPS HEAD BOLT M5X12L

QTY

4

A Open

PINK HARDWARE BAG.

B Attach the

WATER BOTTLE HOLDERS (9)

to the

SEAT FRAME (10) using 4 BOLTS

(H).

PART

I

J

BLUE HARDWARE BAG

TYPE

SOCKET HEAD BOLT

DESCRIPTION

M8X15L

SPRING WASHER Φ8.2XΦ13.5X2.0T

QTY

4

4

C Open

BLUE HARDWARE BAG.

D Attach the

SEAT FRAME (10) to the MAIN

FRAME (2) using 4 BOLTS (I) and 4

SPRING WASHERS (J).

63

64

CHAPTER 10: BIKE SPECIFICATIONS AND ASSEMBLY GUIDE

10.2 ASSEMBLY INSTRUCTIONS - CONTINUED

STEP 5

PART

K

L

M

PURPLE HARDWARE BAG

TYPE DESCRIPTION

SOCKET HEAD BOLT

SPRING WASHER

WAVE WASHER

M8X50L

Φ8.2XΦ13.5.0X2.0T

Φ8.2XΦ18.0X1.5T

QTY

4

4

4

A Open

PURPLE HARDWARE BAG.

B Attach the

SEAT BASE (11) to the SEAT

FRAME (10) using 4 BOLTS (K), 4 SPRING

WASHERS (L) and 4 WAVE WASHERS

(M).

PART

N

ORANGE HARDWARE BAG

TYPE

SOCKET HEAD BOLT

DESCRIPTION

M8X60L

QTY

2

A Open

ORANGE HARDWARE BAG.

B Attach the

SEAT BACK (12) to the SEAT

FRAME (10) using 2 BOLTS (N).

CHAPTER 10: BIKE SPECIFICATIONS AND ASSEMBLY GUIDE

10.2 ASSEMBLY INSTRUCTIONS - CONTINUED

STEP 6

NOTE: All hardware for this step is preinstalled.

A Attach the

CONSOLE CABLES (5) to the

CONSOLE (13).

B Attach the

CONSOLE (13) to the

CONSOLE MAST (6) using 4 PRE-

INSTALLED BOLTS (14).

C Attach

PEDALS (15) to the CRANK (16)

with the provided 15mm/17mm flat wrench.

65

66

CHAPTER 10: BIKE SPECIFICATIONS AND ASSEMBLY GUIDE

10.2 ASSEMBLY INSTRUCTIONS - CONTINUED

FINAL ASSEMBLY

CHAPTER 10: BIKE SPECIFICATIONS AND ASSEMBLY GUIDE

10.3 ADJUSTING THE PEDAL STRAPS AND SEAT

ADJUSTING THE PEDAL STRAPS

The straps are designed to fit your individual foot size and should be adjusted tight enough to keep your foot from slipping. The pedals include spring loaded clips for easy adjustment. To tighten the strap, pull down the open end of the strap. To loosen the strap, push down on the top of the clip and pull the strap up. Release the clip to lock the strap in place.

67

68

CHAPTER 10: BIKE SPECIFICATIONS AND ASSEMBLY GUIDE

10.4 LEVELING THE BIKE

STABILIZING THE MATRIX R5X-05 BIKE

After positioning the bike in its intended location, check its stability by attempting to shake it side to side. Shaking or wobbling indicates that your bike needs to be leveled. Determine which leveler is not resting completely on the floor. Rotate the left or right foot pad, and repeat the adjustment as necessary until the bike is stable.

CHAPTER 10: BIKE SPECIFICATIONS AND ASSEMBLY GUIDE

10.5 TV BRACKET INSTALLATION INSTRUCTIONS

The Matrix Recumbent bike is capable of having a MYE Entertainment or Web Ready (PCTV) television installed using an integrated bracket.

Follow the instructions below to install the TV and TV bracket, and the instructions located in the TV owner's manual to program the television.

1) Remove the console from the unit as outlined in Section 9.1.

2) Remove the 6 screws holding the console front to the back and split the console (Figures A & B).

FIGURE A FIGURE B

3) Remove the 2 screws holding on the blank headphone jack plastic to the console, and remove the plastic (Figures C & D).

FIGURE C

4) Remove the wire in the console that goes from the UCB to the board on the console back (Figure E).

5) Install the new Y cable sent with the TV bracket kit to replace the wire removed in Step 4 (Figure F).

FIGURE D

FIGURE E FIGURE F

69

CHAPTER 10: BIKE SPECIFICATIONS AND ASSEMBLY GUIDE

10.5 TV BRACKET INSTALLATION INSTRUCTIONS - CONTINUED

6) Run the white end from the Y cable through the headphone jack hole in the console plastic, and plug it into the headphone jack sent with the

TV bracket set (Figure G).

7) Mount the headphone jack into the console plastic using the 2 screws removed in Step 3 (Figure H).

FIGURE G FIGURE H

NOTE: Steps 8 - 13 should only be done if installing a MYE TV (the PCTV does not use the entertainment overlay).

8) Remove the existing heart rate overlay from the lower portion of the console (Figure I).

9) Clean the console area with alcohol to remove any left over adhesive from the console plastic (Figure J).

10)

FIGURE I

10) Peel off the protective film from the back of the entertainment keypad / overlay (Figure K).

11) Push the ribbon cable end through the hole in the console plastic (Figure L).

FIGURE J

70

FIGURE K FIGURE L

CHAPTER 10: BIKE SPECIFICATIONS AND ASSEMBLY GUIDE

10.5 TV BRACKET INSTALLATION INSTRUCTIONS - CONTINUED

12) Press the entertainment keypad / overlay into the cut out in the console plastic (Figure M).

13) Plug the ribbon cable into the pins on the UCB (Figure N). Make sure that the pins and ribbon cable are correctly aligned with no pins open on the UCB.

FIGURE M FIGURE N

14) Mount the TV bracket to the console using 4 socket head screws sent with the TV bracket kit (Figure O).

15) MYE TV - Plug the 4 pin black connector side of the power wire into the UCB in the port marked TV Power for EP (Figure P). PCTV - Plug the 4 pin black connector to the power wire coming up the console mast from the base of the unit.

FIGURE O FIGURE P

16) Plug the side of the controller wire labeled To Console into the CSafe board mounted on the console back (Figure Q). The MYE TV should be plugged into the TV port, the PCTV should be plugged into the PCTV port. If installing a PCTV, also change switch SW1 to the top location.

17) Route the net cable through the console. This wire is not plugged into the UCB, but should be routed through the console to hide the wire.

The 8 pin black connector on the net wire should stick out the bottom of the console along with the HR wiring (Figure R).

18) Connect one end of the coax cable to the board on the back cover using the adaptor sent with the TV kit (Figure S).

FIGURE Q FIGURE R FIGURE S

71

CHAPTER 10: BIKE SPECIFICATIONS AND ASSEMBLY GUIDE

10.5 TV BRACKET INSTALLATION INSTRUCTIONS - CONTINUED

18) There should now be 4 wires sticking out the top of the console - TV power wire, net wire, coax cable, and controller wire (Figure T).

19) Re-attach the console back to the front using the bottom 6 screws removed in Step 2. NOTE: Be sure to route the wiring so that it is not pinched by the bracket or plastic when installing the top 2 screws (Figure U). The small cover with the Matrix logo that makes up the top of the rear console cover is no longer used with a TV bracket.

20) Mount the console back onto the unit making sure to make all the necessary wire connections including the coax cable.

FIGURE T

21) Mount the plastic front plate to the TV (Figure V).

22) Plug the coax cable into the back of the TV (Figure W).

FIGURE U

MYE TV PCTV

FIGURE V FIGURE W

23) Plug the power wire into the back of the TV (Figure X).

24) Plug the controller wire into the back of the TV (Figure Y). NOTE: The controller wire should be plugged into the PCTV port on the PCTV.

72

MYE TV

FIGURE X

PCTV MYE TV

FIGURE Y

PCTV

CHAPTER 10: BIKE SPECIFICATIONS AND ASSEMBLY GUIDE

10.5 TV BRACKET INSTALLATION INSTRUCTIONS - CONTINUED

25) If installing a PCTV, plug the net wire into the back of the TV (Figure Z). NOTE: The net wire is not used if installing a MYE TV, and should be hidden by the plastic covers.

26) If the PCTV will be using a wireless signal, plug the dongle into the back of the TV and mount the USB flash drive to the console plastic using double sided foam tape (Figure AA).

FIGURE Z FIGURE AA

27) Put the TV into place on the TV bracket being sure to tuck the tabs of the plate installed during Step 20 into the console plastic (Figure BB).

28) Mount the TV to the TV bracket using 4 screws sent with the TV (Figure CC).

FIGURE BB FIGURE CC

29) Put the back cover onto the TV and secure with 4 screws (Figure DD).

30) Install the console back onto the unit making sure to connect the coax cable and net wire.

31) Plug a network wire (if using a PCTV not using wireless), power wire (PCTV only) and / or a coax cable to the port on the front of the unit

(Figure EE).

32) Enter into Engineering Mode and set the Audio Source setting for TV or PCTV as needed.

33) Program the TV as shown in the TV owner's manual.

FIGURE DD FIGURE EE

73

CHAPTER 11: SOFTWARE UPGRADE GUIDE

11.1 SOFTWARE UPGRADE PROCEDURE

NOTE: If you install the software while in a self powered mode, keep pedaling while the software is being installed. After the software has completely loaded, stop pedaling for 30 seconds to allow the machine to completely power down.

1. Create a file on the USB flash drive which will be used. The folders should be MATRIX\FW\UCB (create a folder called MATRIX, then a folder in MATRIX called FW, then a folder in FW called UCB). Or you can put USB flash drive into the console and press ENTER, 9, 0, 0, 1, ENTER on the keypad and the USB will create the folders (Figure A)

2. Copy the software files into the UCB folder on the USB flash drive (the access should read \MATRIX\FW\UCB - Figure B).

3. Insert the USB flash drive into the USB port on the console (Figure C).

4. With the display is in standard operation mode, press ENTER, 9, 0, 0, 1, ENTER on the keypad. Press the LEVEL UP or DOWN keys to choose the correct software (if there are more than one version on the USB flash drive). Once the correct software is found, press ENTER and the upgrade procedure will start.

5. If the console beeps and display shows 04A0 (Figure D), please remove the USB drive, turn off & turn on the machine again, and the display will go back to standard operation.

FIGURE A FIGURE B

74

FIGURE C FIGURE D

NOTES

75

76

MATRIX FITNESS SYSTEMS CORP.

1610 LANDMARK DRIVE COTTAGE GROVE WI 53527 USA

TOLL FREE 866.693.4863 www.matrixfitness.com FAX 608.839.1717

REV. 01

KO

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents