advertisement
Index & Warnings
SERVICE MANUAL
Schematic Diagrams
CODE : 277322
GENERALMUSIC S.p.a. Sales Division:47842 S.Giovanni in Marignano (RN) ITALY - Via delle Rose, 12 - tel. 0541/957404 - fax0541/957404 - http://www.generalmusic.com
Notice
Service must be carried out by qualified personnel only. Any tampering carried out by unqualified personnel during the guarantee period will forfeit the right to guarantee.
For a correct operation of the instrument, after having switched off, be careful to wait at least 3 seconds before switching on again.
To improve the device's specifications, the schematic diagrams may be subject to change without prior notice.
Schematic Notes
All components marked by this symbol have special safety characteristics, when replacing any of these components use only manufacturer's specified parts.
The (µ) micro symbol of capacitance value is substituted by U. The (Ω) omega symbol of resistance value is substituted by E.
The electrolytic capacitors are 25Vdc rated voltage unless otherwise specified. All resistors are 1/4W unless otherwise specified.
All switches shown in the "OFF" position. All DC voltages measured to ground with a voltmeter 20KOhm/V.
Soldering point.
Male connector.
Female connector.
M/F faston connector.
Test point.
Supply voltage.
Logic supply ground.
Analog supply ground.
Signal ground.
Chassis ground.
Flag joined with one or more flags with the same signal name inscribed.
ATTENTION
Observe precautions when handling electrostatic sensitive devices
1 r
r 2
-
+
+
-
3 r
r 4
5 r
r 6
Spare Parts
26
26
27
28
22
23
24
25
18
19
20
21
15
15
16
17
33
34
35
36
37
29
30
31
32
11
12
13
14
7
8
9
10
6
7
4
5
1
2
3
237064
237065
229030
347283
227038
177476
177325
150591
141202
141184
140526
140212
130297
130283
120319
120125
120111
120108
120099
120098
110614
110297
110291
180637
177474
887074
768030
768126
768043
768042
768128
767987
768002
667613
667610
659027
717054
347287
347286
347187
XLR MALE-FEMALE SIGNAL CABLE (mt. 1.5)
DISPLAY & SETTING BOARD
SIGNAL INPUTS CONTROLS & MIDI INTERFACE BOARD
POWER AMPLIFIER BOARD
POWER SUPPLY BOARD
CONVY PROCESSOR BOARD
MAINS FILTER BOARD (EU)
MAINS FILTER BOARD (US)
CONTROLS PANEL
METAL GRID
CYL. KNOB WHITE CAP
WOODEN CABINET
PLASTIC HANDLE
HANDLE SET
RUBBER HANDLE
TRANSFORMER (EU)
TRANSFORMER (US)
2" COMPRESSION DRIVER TWEETER
COMPRESSION DRIVER HORN
15" SPEAKER
AMPLIFIER HEAT SINK
STAND ADAPTOR
DISPLAY RED GLASS
XLR MALE SOCKET
XLR FEMALE SOCKET
GRAY BUTTON
DIN SOCKET
MAINS CORD (EU)
MAINS CORD (US)
WL 4x15 MAINS CORD SCREW
M5x35 MAINS CORD SCREW
M6x25 MAINS CORD SCREW
M5x30 MAINS CORD SCREW
M4x25 MAINS CORD SCREW
M4x20 MAINS CORD SCREW
MAINS INLET (EU)(US)
2 POLES 2 POS. SLIDE SWITCH
MAIN SWITCH (EU)(US)
ADHESIVE "GENERALMUSIC-LEM" BRAND
DRIVER HOLDER
Inputs Controls Panel
TOUR MASTER 15,2 ACTIVE - Technical Specification
COMPONENTS
HIGH section POWER HANDLING
(EIA RS-426A)
LOW section POWER HANDLING
(EIA RS-426A)
IMPEDANCE (nominal)
CONSTRUCTION
WEIGHT
DIMENSIONS
INPUT
A/D converter
D/A converter
Dynamic range
Sampling rate
CROSSOVER
SPEAKER SPECIFICATIONS
High
Low
High
Low
W continuous
W peak
W continuous
W peak ohm
2" driver with controlled directivity horn
15" low frequency speaker
75
240
8
4
800
2400
Cabinet: birch playwood
Finish: Black scratch-resistant paint
Protection grille: metal grille kg - lbs.
48,5 - 106,8 mm - in.
470x790x465 (LxAxP) - 185x311x183(WxHxD)
PROCESSOR SPECIFICATIONS
Sensitivity dB 0 (0.775Vrms)
Impedance
Frequency
Slope
Kohm bit bit dB
KHz
Hz dB/oct.
30 (balanced) - 15 (unbalanced)
18
18
105
48
1350
24
HIGH section POWER AMPLIFIER
LOW section POWER AMPLIFIER
AMPLIFIERS DISTORTION
CONTROLS
W continuous
W continuous
THD +Noise
150
650
<0,02%
VOLUME control
UP & DOWN selector buttons
MIDI button
DISPLAY
Earth Lift
2-digit display
CONNECTORS
POWER SUPPLY
SIGN/COMP LED
1 XLR-F +1 XLR-M (input + link)
MIDI in & MIDI THRU
230V ±15% 50/60Hz - 115V ±15% 50/60Hz
SYSTEM SPECIFICATIONS
Hz 50 ÷ 20000 (-10dB) FREQUENCY RESPONSE
SENSITIVITY SPL 1W/1m dB
MAX SPL continuous horizontal °
98
127
60 (±10) DISPERSION ANGLE vertical
DIRECTIVITY Factor (Q)
DIRECTIVITY Index Di dB
Note:the system specifications have been calculated using PRESET n.1 FLAT
40 (±7)
12
11 (+2.8 , -4)
BIAS ADJUSTMENT
Instruments, materials and tools:
- Audio Generator
- Dual Trace Oscilloscope
- Digital Voltmeter (or Multimeter)
- 4
Ω
500W and 8
Ω
100W Resistors
- Temperature Meter
Setup:
- Connect the Audio Generator to the input and set its output at 2KHz sinusoidal signal.
- Insert the temperature sensor through the interstize between the heatsink and R93 (PTC).
- Connect the 4
Ω
500W resistor to the amplifier output instead of the woofer speaker and 8
Ω
100W instead of tweeter speaker.
- Connect the oscilloscope probes (setting 20V/div.,1ms/div.) on the loads.
- Insert the voltmeter terminals on R107.
ADJUSTMENT PROCEDURE
1) Turn on the amplifier, pressing "UP" "DOWN" and "MIDI" simultaneously, check that the display shows "C".
2) Set the input signal to 0dB (0.775Vrms).
3) When the temperature has reaches about 45°C (109°F) set the signal input to minimum (0 or ).
4) Adjust the trimmer R111 to read a voltage of 6mV ±0.1 on the multimeter.
5) Check that the voltage across the R108 resistor has the same value.
6) At the same temperature condition, adjust the VR1 trimmer to read 2.2mV ±0.1 at R24 resistor.
7) Check that the voltage on the R25 resitor has the same value.
Veryfing:
1) Increase the input level to obtain an output voltage about of 0.5Vpp.
2) Check with the oscilloscope that the output signal is without a cross-talk distortion and eventually slightly
adjust the R111 or VR1 position until distortion disappears.
(Note: the voltage value across the R107 or R108 resistor must not exceed 10mV and the R24 or R25 resistor must
not exceed 4mV).
LIMITER ADJUSTEMENT
1) Increase the input level to 10dB, adjust the trimmer VR1 until clipping distortion disappears.
2) Verify tha the led change colour from green to red.
3) Re-connect the speakers instead of the 4
Ω
and 8
Ω
resistors.
7 r
SPARE PARTS LIST
ACCESSORIES
887074 XLR Female-Male Signal Cable (1.5mt)
277310 Owner’s Manual
ASSEMBLY
667613 Controls Panel
659027 Cyl. Knob White Cap
237064 Transformer (230V)
237065 Transformer (115V)
150591 Display Red Glass
110614 Mains Socket
110291 Power Switch
110037 T6.3A Fuse 6.3x32mm (US)
110035 T2.5A Fuse 6.3x32mm (US)
110034 T800mA Fuse 6.3x32mm (US)
110022 T8A Fuse 6.3x32mm (US)
110029 T4A Fuse 5x20mm (EU)
110023 T8A Fuse 5x20mm (EU)
110018 T6.3A Fuse 5x20mm (EU)
110015 T800mA Fuse 5x20mm (EU)
110014 T2.5A Fuse 5x20mm (EU)
667506 Left Side Bar
717054 Wooden Cabinet
667610 Metal Grid
347287 Plastic Handle
347286 Plastic Set
347283 2" Comprission Driver Horn
347187 Plastic Grip
229030 2" Compression Driver Tweeter
227038 15" Speaker
177474 Driver Holder
177325 Stand Adapter
130297 Mains Cord (EU Version)
130283 Mains Cord (US Version)
CONVY Processor Board
758128 CONVY Processor Board (PCB#313020)
230569 *
141059 *
FL5R200PNT EMI Coil For Signal
Con V M 9 C Mini Mate Burndy
141015 *
141013 *
141010 *
100943 *
Con V F 14c P=1.27 Mmatch Amp
Con V F 10c P=1.27 Mmatch Amp
4 Contacts Vert Female Connector
MC33079 Quad Ln Op Amp
100919 *
100737 *
100643 *
100642 *
100612 *
100061 *
100059 *
100058 *
MC33078 Dual LN J-Fet Operational Amplifier
ADMOD79 2ch Ad Delta Modulator
AD1865N Dual 18bit Dac
TS93C46 1Kbit Eeprom Memory
74HC374 Octal D-Type Flip-Flop
TL072 Dual J-Fet Operational Amplifier
7805 +5V 1A Voltage Regulator
7905 -5V 1A Voltage Regulator
080103 *
050494 *
050492 *
010722 *
010720 *
557026 *
105001 *
1N4148 100mA 75V Signal Diode
Resistor Array 10K X5 1/8w 5%
10Kx8 1/8w 5% Resistor Array
24.576MHz Quartz Resonator
12MHz Ceramic Resonator With Capacitors
AT89C55-12JC Programmed CPU
CONVY Dsp Convolver
Power Supply Board
768042 * Power Supply Board (PCB#317191)
141060 ** Con V M 12c Mini Mate Burndy
141013 ** Con V F 10c P=1.27 Mmatch Amp
140081 ** H 2c P=10 Terminal Block
140069 ** H 3c P=10mm Terminal Block
100060 ** 7815 +15V 1A Voltage Regulator
100059 ** 7805 +5V 1A Voltage Regulator
100049 ** 7915 -15v 1a Voltage Regulator
080606 ** GBU8D 8A Rectifier Diodes Bridge
080168 ** W02M 1.5A Rectifier Diodes Bridge
030882 ** 10000uF 50V Snap-In Electrolytic Capacitor
030881 ** 10000uF 50V Snap-In Electrolytic Capacitor
030866 ** 4700uF 100V Snap-In Electrolytic Capacitor
030858 ** 4700uF 25V 20% Vert Electrolytic Capacitor
030560 ** 4700uF 80V 20% Snap-In Electrolytic Capacitor
Signal Input Controls & MIDI Interface Board
768126 Signal Input, Controls & MIDI Interface Board (PCB#313019)
757942 * Photores Coupler
141202 *
141184 *
141064 *
Hor. Male XLR Socket (M21bc Nuova Asme)
Hor. Male XLR Socket (NC3FPRH Neutrik)
9 Contacts Hor. Male Connector r 8
141010 *
140212 *
100602 *
100061 *
100035 *
090194 *
090183 *
080734 *
080245 *
080103 *
074570 *
070125 *
140526 *
4 Contacts Vert Female Connector
Horizontal Female 5 Poles Din Socket
74HC04 Hex Inverter
TL072 Dual J-Fet Operational Amplifier
6N138 Optocoupler
BC560 TO92 LN Pnp Transistor
BC550 To92 Ln Npn Transistor
Led 2.5x5mm Rect Diff Red-Grn LED
7V5 1W 5% Zener Diode
1N4148 100mA 75V Signal Diode
5K lin. 31 clicks Potentiometer
1K 20% Vertical Linear Trimmer
Gray Button
Display & Setting Board
768030 * Display & Setting Board (PCB#319046)
141015 ** Con V F 14c P=1.27 Mmatch Amp
140526 ** Microswitch 100V 100ma 0.8mm
080717 ** HDN1105 7 Segments Display
Mains Filter Board
767987 * Mains Filter Board (Pcb#315016) (EU)
768002 * Mains Filter Board (Pcb#315016) (US)
230565 ** 2.5mH 250V 3A AC Line Filter
140010 ** 3 Contacts P=10 Vert Terminal Block
110113 ** Fuse Clip 5x20mm 6A max (EU)
110114 ** Fuse Clip 6.3x32mm 10A Max (US)
020493 ** 100n 250Vac MKP EMI Capacitor “Siemens”
010719 ** 2n2 250Vac 7A 20% AC Line “Y” Filter “Murata”
Power Amplifier Assembly
727524 Power Amplifier Assenbly
768043 * Power Amplifier Board (PCB#319044)
141059 ** 9 Contacts Vert. Male Connector
141058 ** 6 Contacts Vert. Male Connector
110316 ** Relay 24V / 1 Switch no 16A 250V
110307 ** Relay 24V / 2 Switch 5A 250V
100084 ** TL074 Quad J-Fet Operational Amplifier
100061 ** TL072 Dual J-Fet Operational Amplifier
090920 ** Mje803 TO126 Npn Darl Transistor
090917 ** MJE350 TO126 Pnp Transistor
090916 ** MJE340 TO126 Npn Transistor
090201 ** 2N5401 TO92 Pnp Transistor
090200 ** 2N5550 TO92 Npn Transistor
090924 ** MJL21194 NPN Transistor
090923 ** MJL21193 PNP Transistor
090920 ** MJE802P PNP Transistor
090919 ** MJE15031 PNP Transistor
090918 ** MJE15030 NPN Transistor
090917 ** MJE350 PNP Transistor
090916 ** MJE340 NPN Transistor
090863 ** TIP36C PNP Transistor
090862 ** TIP35C NPN Transistor
080282 ** 13V 1W 5% Zener Diode
080261 ** 10V1W 5% Zener Diode
080245 ** 7V5 1W 5% Zener Diode
080241 ** 5V6 1W 5% Zener Diode
080171 ** FE6B 6A 100V Fast Recovery Diode
080156 ** 1N4002 1A 100V Rectifier Diode
080103 ** 1N4148 100mA 75V Signal Diode
070106 ** 470E 20% Horizontal Linear Trimmer
070082 ** 220E 20% Horizontal Linear Trimmer
080819 * PTC 70 Pth59f04bg222ts
080607 *
080606 *
KBPC25 25A 200V Bridge Rectifier Diode
GBU8D 8A Rectifier Diodes Bridge
Notes:
Each spare part is single quantity unless otherwise specified
Asterisk prefix explanation:
Omitted = First level spare part.
One asterisk
Two asterisks
= Second level, part of previous listed first level part.
= Third level, part of previous listed second level part.
Three asterisk =.......................
Any request for not above mentioned part must encompass specific description including:
1) Model name,
2) Section,
3) Module code,
4) Reference name,
5) Quantity number.
advertisement
Related manuals
advertisement