™

Model 890 Four Wheel Hose Cart

Owner’s Manual

VISIT OUR WEBSITE: WWW.LIBERTYGARDENPRODUCTS.COM

OR CALL US TOLL FREE AT 1-866-820-5805, MONDAY - FRIDAY 9 A.M. - 5 P.M. EST

LIBERTY GARDEN PRODUCTS, INC.

1161 SOUTH PARK DRIVE, KERNERSVILLE NC 27284

IMPORTANT: READ THE OWNER’S MANUAL BEFORE ASSEMBLING

A1

TOOLS REQUIRED: TWO ADJUSTABLE WRENCHES, 1 0 mm BOX END

WRENCH, PHILLIPS HEAD SCREWDRIVER

Estimated Assembly Time: 30 Minutes

PARTS LIST

E

B

A2

C

F

G

D

A1. / A2.

FRAME SIDES (2 PIECES)

B.

U-HANDLE (1)

C.

TIRES (4)

D.

AXLE RODS (2)

E.

SPOOL ENDS (2)

F.

SPOOL RODS (3)

G.

LEADER HOSE (1)

Important!

Some of your hose cart parts shown will come factory assembled.

H

J

K

I

L

M

O

N

P

Q

R

H.

CRANK HANDLE (1)

I.

J.

K.

L.

M.

N.

SPRING (1)

SPACER WASHER (1)

RUBBER HANDLE W/BOLT (1)

U-BUSHING (1)

WATER CONNECTION UNIT (1)

(Brass Swivel, U-Bushing, Galvanized Tee)

13 MM BOLT W/NUTS (12)

O.

40 MM BOLT W/NUTS (4)

P.

AXLE NUTS (4)

Q.

AXLE WASHERS (4)

R.

U-HANDLE BOLT W/WING NUTS (2)

IMPORTANT: LAY OUT ALL PARTS AND FASTENERS. MAKE SURE ALL PARTS ARE ACCOUNTED

FOR. IF ANY PART IS MISSING PLEASE CONTACT LIBERTY GARDEN PRODUCTS AT

1-866-820-5805. DO NOT CONTACT THE RETAILER. YOU CAN ALSO VISIT OUR WEBSITE,

WWW.LIBERTYGARDENPRODUCTS.COM, FOR MORE INSTRUCTIONS PICTURES AND HELPFUL

HINTS. CONTACT [email protected] WITH QUESTIONS.

2

1. Set the frame sides upright and insert side (A1 and A2) together as shown. See Figure 1

A2

2. On the open end of the frame slide the u-handle

(B) into the frame. Align the holes then insert and tighten the u-handle bolts and wing nuts (R) securely.

See Figure 2

A1

B

R

A1

A2

FIGURE 1

FIGURE 2

3. Slide the axle rods (D) through the axle housing on the frame. See Figure 3

5. Set the cart upright on the wheels. See

Figure 6

D

FIGURE 3

4. Place the wheel (C) over the axle. Place the axle washer (Q) over the thread and screw on axle nut

(P) and tighten securely. Repeat for each remaining wheel. See Figures 4 & 5

C

FIGURE 6

FIGURE 4

P

Q

FIGURE 5

NOTE: Use two open end or adjustable wrenches to tighten the axle nuts.

3

7.

Using the 12 / 13 mm screws and lock nuts

(N) fasten the three spool rods (F) to each end of the spool ends (E) using a phillips head screw driver and a small adjustable wrench or a 1 0 mm box end wrench and tighten securely.

See Figures 7, 8 & 9

E

E

FIGURE 8

F

N

FIGURE 7

FIGURE 9

Attach 12

13 mm screws and lock nuts

F

E

M

10. Thread the water connection unit (M) onto the spool end. (E) Tighten using an adjustable wrench. See Figure 10

WARNING: DO NOT OVERTIGHTEN

THE GALVANIZED TEE THIS COULD

CAUSE STRIPPING OF THE THREADS .

FIGURE 10

M

FIGURE 11

M

O

11. Place the spool and water connection unit

(M) on the frame so the u-bushing is oriented over the holes on the frame. See Figure 11

J

I

L

FIGURE 12

12. Insert two 40mm bolts and nuts (O) through the u-bushing on the water connection unit (M) at the u-handle end of the frame. Hand tighten.

See Figure 12

FIGURE 14

L

O

O

FIGURE 13

13. Slide the Spacer washer (J) , spring (I) then the other u-bushing (L) over the spool end at the front of the cart.

See Figure 13

14. Insert two 40mm bolts and nuts u-bushing (L)

See Figure 14

15. Tighten all four of the 40mm nuts and bolts (O) with open end or adjustable wrenches. See Figure 15

and the frame.

(O) through the

O

NOTE: The spring may need to be pushed in so the u-bushings align with the frame holes.

FIGURE 15

16. Attach the crank handle (H) to the spring loaded spool end and hand tighten. DO NOT

OVER TIGHTEN. See Figure 16

H

K

FIGURE 17

H

FIGURE 16

17. Using an adjustable wrench attach the rubber handle and bolt (K) to the end of the crank handle (H) and tighten with a adjustable wrench. See Figure 17

18. Attach the Leader Hose (G) to the end of the brass swivel. DO NOT OVER TIGHTEN.

See Figure 18

19.

Attaching Your Garden Hose:

The 890 is designed to hold up to

200’ of 5/8” garden hose. Attach your hose to the brass adapter (on the galvanized tee). Loop the hose over the spool end (as shown) to avoid kinking. See Figure 19 & 20

Your Model 890 host cart is now ready to use. Attach the end of the leader hose to your water supply.

FIGURE 19

FIGURE 18

6

G

FIGURE 20

CARE INSTRUCTIONS

Your hose reel cart is manufactured with the finest quality components available. This product will give you many seasons of reliable and functional hose storage. All components are manufactured to rigorous quality standards not common in other consumer grade hose reels available today. As with any steel product, there is always the chance for rust developing over time. Your hose reel finish is designed for industrial applications, but even the toughest of coatings can be compromised by scratches. Such minor surface damage can occur in shipping despite our best efforts. We have found that most scratches occur during assembly and/or installation (in the case of wall mounted hose reels). If the base metal is exposed to the elements long enough, rust will develop. In the case of wall mounted reels, be sure to use damage. Scratches can easily be repaired by using standard automotive touch-up body paint. Some of our most loyal customers recommend that at the end of each season, the unit be cleaned and painted with a clear acrylic paint.

When you install your hose reel, be sure the hose washers are in place and all fittings are secure. If you live in more temperate climates, be sure to drain the unit of any residual water before storing.

• DO NOT EXPOSE UNIT TO FREEZING TEMPERATURES while water remains in the plumbing system, this can damage the swivel.

• DO NOT leave water running through the hose reel cart while not in use or unsupervised.

• DO NOT consume water from garden hose; not fit for human consumption.

WARNING! This product contains one or more chemicals known in the state of California to cause cancer and birth defects or reproductive harm. Wash hands after handling.

CALL US AT 1-866-820-5805 IF YOU HAVE ANY QUESTIONS

REGARDING CARE INSTRUCTIONS

7

TROUBLE SHOOTING GUIDE

Problem: Swivel head is not rotating, causing the leader hose to kink up.

Solution: Remove leader hose and turn the square head of the swivel several times; apply lubricant.

Problem: Your new Liberty hose reel is leaking at the swivel.

Solution: Apply Teflon/Plumber's Tape on the threads or/and make sure fixtures are tightened.

It is normal for the swivel to leak slightly until the O-rings are wet and have seated. If the leaking continues, try these steps: (It is not necessary to return the hose reel)

1. If the leader hose is attached to the swivel, unscrew the hose and look inside the swivel.

2. Check that the hose washer is inside the nut. You may contact Liberty Garden Products for a new hose washer or obtain one at any hardware store.

3. If your swivel is old, the O-rings may be worn, please contact us for a new set of O-rings.

4. If these steps do not solve your leaking problem, contact Liberty Garden Product’s customer service.

SHAFT O-RING HOUSING O-RING

SNAP RING

INSERT

WASHER

O-RING

NUT

CALL US AT 1-866-820-5805 IF YOU HAVE ANY QUESTIONS

REGARDING TROUBLESHOOTING AND MAINTENANCE

8

LIBERTY GARDEN PRODUCTS LIMITED WARRANTY

(Effective September 11, 2017)

This limited warranty is applicable to each original end-customer (hereinafter “Customer”) purchasing the model 890 four wheel hose reel cart consisting of the structural metal frame and spool (hereinafter the “Structural Frame”) and various other non-frame components

(hereinafter the “Non-Frame Parts”) sold by Liberty Garden Products, Inc. (hereinafter “Company”) for Customer’s own use and not for resale. The Structural Frame and Non-Frame Parts are collectively referred to herein as the “Products”..

1. LIMITED WARRANTY; EXCLUSIVE REMEDIES:

1.1. LIMITED WARRANTY ON PRODUCTS: Company warrants solely to the original Customer that (a) the Structural Frame will be free from defects in materials and workmanship under normal use for a period of three (3) YEAR(S) from the date of original retail purchase, and (b) the Non-Frame Parts (which consist of the crank handle, swivel and water connections, leader hose and tires), will be free from defects in materials and workmanship under normal use for a period of ONE (1) YEARS from the date of original retail purchase. Notwithstanding the foregoing, the colors and finishes of the Products may vary within a reasonable scope due to unavoidable color variations in different production batches, and such variations shall not constitute a material defect. This limited warranty is limited solely to the original Customer with proof of purchase and is not transferable

1.2. THE WARRANTY: During a covered Product’s limited warranty period, Company will, at Company’s sole option and discretion, (1) repair the defective component or product without charge or (2) replace the defective component or product without charge.

1.3.

The foregoing limited warranty is subject to the Customer’s proper storage, transportation, handling and use of the Products as the same are defined within Company’s then-current published guides and instructions for use and care. The limited warranty does not include defects due to normal wear and tear, abuse or misuse, mishandling, neglect, accident, fire, lightning, sunlight or other natural hazard, delivery or transportation damage, failure to follow applicable directions or instructions, or improper or inadequate cleaning, maintenance, care, repairs, modifications, or use beyond a Product’s intended use. Please note that since the Structural Frame is made from steel rust may occur over time. As such, this limited warranty does not include rust or defects due to the same.

1.4. LIMITED WARRANTY CLAIMS PROCEDURE: To obtain performance under this limited warranty, Customer shall notify Company in writing (to Liberty Garden Products, Inc., 1161 South Park Drive, Kernersville, NC 27284, Attn: Customer Service / Warranty Department), by email

(to [email protected]), or by telephone (to (336) 992-3595) with a full description of the defect that is covered by warranty and a copy of the dated proof of purchase of the applicable product.

• Company shall review each such claim and issue Customer a return merchandise authorization (“RMA”) in the event that the described defect or condition merits warranty review as determined by Company. Customers who have been issued a RMA shall, at Company’s election, return the covered item to the same physical address listed above for reporting initial claims. Company shall not accept any returned product without a RMA.

• Upon receipt, Company will evaluate the returned product(s) to determine if there is a warranty claim and, if so, how Company wishes to remedy the same. During a covered product’s respective limited warranty period, Company will, at Company’s sole and absolute option and discretion,

(1) repair the defective component or product without charge or (2) replace the defective component or product without charge. Refunds are not available pursuant to this limited warranty.

• Customer is solely responsible for transportation of the covered product(s) to the Company for evaluation (if applicable and requested by

Company). In the event that Company determines that a claim under this limited warranty is justified, Company shall be responsible for transportation of the repaired, corrected, replaced or exchanged product back to Customer. Customer shall be solely responsible for the transportation of any product back to Customer if Company determines that a claim under this warranty is not justified.

• Any repaired, corrected, replaced or exchanged Products shall be subject to the Limited Warranty set forth to the duration of the original limited warranty period as set forth in Section 1.1. and not for any extended duration, following their repair, correction, replacement or exchange.

1.5. IF A COMPANY PRODUCT DOES NOT CONFORM TO THESE LIMITED WARRANTIES, THE PURCHASER’S SOLE

AND EXCLUSIVE REMEDY IS, AT COMPANY’S SOLE AND EXCLUSIVE OPTION, THE (1) REPAIR OF ANY DEFECTIVE

PRODUCT OR COMPONENT PART OR (2) REPLACEMENT OF ANY DEFECTIVE PRODUCT OR COMPONENT PART.

THE LIMITED WARRANTY AND REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND MADE IN LIEU OF ALL

OTHER WARRANTIES, REMEDIES, RIGHTS OR CONDITIONS, WHETHER ORAL OR WRITTEN, EXPRESS OR

IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. COMPANY SPECIFICALLY

DISCLAIMS, WITHOUT LIMITATION, ANY AND ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, OF ANY KIND. IF

COMPANY CANNOT LAWFULLY DISCLAIM IMPLIED WARRANTIES UNDER THIS LIMITED WARRANTY, ALL SUCH

WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THIS LIMITED WARRANTY. The Company does not assume or authorize any person to assume for them any other liability in connection with the Products.

9

LIBERTY GARDEN PRODUCTS LIMITED WARRANTY CONTINUED

2. EXCLUSION AND LIMITATION OF LIABILITY:

IN NO EVENT, WHETHER BASED ON CONTRACT OR TORT OR OTHER LEGAL THEORY, SHALL COMPANY BE

LIABLE FOR ANY INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT

NOT LIMITED TO, DAMAGES TO OTHER PROPERTY, INCONVENIENCE, DAMAGES FOR LOSS OF PROFITS, REVE-

NUE, GOODWILL OR USE, INCURRED BY CUSTOMER OR ANY THIRD PARTY, WHETHER IN AN ACTION IN

CONTRACT, TORT, STRICT LIABILITY, OR IMPOSED BY STATUTE, OR OTHERWISE, EVEN IF ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES.

Some states do not allow the exclusion or limitation of incidental or consequential damages or exclusions or limitations on the duration of implied warranties or conditions, so the above limitations or exclusions may not apply to Customer. In jurisdictions that limit the scope of or preclude limitations or exclusion of remedies or damages, or of liability, such as liability for gross negligence or willful misconduct or do not allow implied warranties to be excluded, the limitation or exclusion of warranties, remedies, damages or liability set forth above are intended to apply to the maximum extent permitted by applicable law. This limited warranty gives the Customer specific legal rights, and the Customer may also have other rights that vary by state, country or other jurisdiction .

3. SEVERABILITY:

If any provision of this limited warranty is held to be illegal, invalid or otherwise unenforceable, such provision will be enforced to the extent possible consistent with its stated intention, or, if incapable of such enforcement, will be deemed to be severed and deleted from this limited warranty, while the remainder of the terms of this limited warranty will continue in full force and effect.

4. DISPUTE RESOLUTION:

This Liberty Garden Products, Inc.

Limited Warranty shall be governed by and construed in accordance with the laws of the State of North

Carolina, without regard to its principles of conflicts of law. The parties acknowledge the exclusive jurisdiction of the federal and state courts of the

State of North Carolina. Any claims or disputes under this

Carolina state and federal courts for such actions.

Liberty Garden Products, Inc.

Limited Warranty shall be heard exclusively in any state or federal courts sitting in Guilford County, North Carolina, and both parties expressly consent to the personal jurisdiction and venue of the North

“Liberty” is a registered trademark of Liberty Garden Products, Inc. Kernersville, NC. All Rights Reserved 2017

Updated 9/26/2017