Manual

Cooking & Holding Oven
Manual Control
Model:
1000-TH-I
• I N STALLATION
• OPERATION
• MAI NTENANCE
W164 N9221 Water Street • P.O. Box 450 • Menomonee Falls, Wisconsin 53052-0450 USA
PHONE: 262.251.3800 • 800.558.8744 USA / CANADA
FAX: 262.251.7067 • 800.329.8744 U . S . A .
www.alto-shaam.com
PRINTED IN U.S.A.
ONLY
MN-28853 • 02/10
Delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Procedures and Precautions . . . . . . . . . . . . . . . . . 2
Sanitation
Sanitation/Food Safety . . . . . . . . . . . . . . . . . . . . . . . 13
Internal Food Product Temperatures . . . . . . . . . . . . . 13
Installation
Installation Requirements . . . . . . . . . . . . . .
Clearance Requirements . . . . . . . . . . . . . . .
Dimension Drawings, weights & capacities .
Options and Accessories . . . . . . . . . . . . . . .
Leveling . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restraint Requirements - Mobile Equipment
Drip Tray Installation . . . . . . . . . . . . . . . . . .
Electrical Specifications . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Service
Thermostat/Indicator Light Sequence
Thermostat Calibration . . . . . . . . . . .
Trouble Shooting . . . . . . . . . . . . . . .
Exterior Service View . . . . . . . . . . . .
Exterior Service Parts List . . . . . . . . .
Cable Heating Kit . . . . . . . . . . . . . . .
Bonnet Assembly View . . . . . . . . . . .
Bonnet Assembly Parts List . . . . . . . .
Operating Instructions
User Safety Information. . . . . .
Before Initial Use. . . . . . . . . . .
Manual Control Operation . . . .
Cooking Oven Characteristics .
General Holding Guidelines . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.8
.8
.9
.9
10
Care and Cleaning
Cleaning and Preventative Maintenance
Protecting Stainless Steel Surfaces . . . .
Cleaning Agents . . . . . . . . . . . . . . . . . .
Cleaning Materials . . . . . . . . . . . . . . . .
Equipment Care . . . . . . . . . . . . . . . . . .
Clean Daily . . . . . . . . . . . . . . . . . . . . . .
Clean the Door Vents . . . . . . . . . . . . . .
Check Overall Condition of Oven. . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
11
11
11
11
12
12
12
12
PG .
2
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
3
3
4
4
5
5
6
7
1000-TH-I
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
14
14
15
16
17
17
18
19
Wire Diagrams
208-240V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
230V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Warranty
Transportation Damage and Claims. . . . . . . Back Cover
Limited Warranty . . . . . . . . . . . . . . . . . . . . . Back Cover
INSTALLATION / OPERATION / SERVICE MANUAL
DELIVERY
U N PA C K I N G
This Alto-Shaam appliance has been
thoroughly tested and inspected to ensure only the
highest quality unit is provided. Upon receipt,
check for any possible shipping damage and report
it at once to the delivering carrier. See
Transportation Damage and Claims section
located in this manual.
This appliance, complete with unattached
items and accessories, may have been delivered in
one or more packages. Check to ensure that all
standard items and options have been received
with each model as ordered.
Save all the information and instructions
packed with the appliance. Complete and return
the warranty card to the factory as soon as
possible to ensure prompt service in the event of a
warranty parts and labor claim.
This manual must be read and understood by
all people using or installing the equipment
model. Contact the Alto-Shaam service
department if you have any questions concerning
installation, operation, or maintenance.
NOTE: All claims for warranty must include the
full model number and serial number of
the unit.
1000-TH-I
1. Carefully remove the
appliance from the
carton or crate.
NOTE: Do not discard the
carton and other
packaging material
until you have
inspected the unit
for hidden damage
and tested it for
proper operation.
®
®
2. Read all instructions in this manual carefully
before initiating the installation of this appliance.
DO NOT DISCARD THIS MANUAL.
This manual is considered to be part of the
appliance and is to be provided to the owner or
manager of the business or to the person
responsible for training operators. Additional
manuals are available from the Alto-Shaam
service department.
3. Remove all protective plastic film, packaging
materials, and accessories from the appliance
before connecting electrical power. Store any
accessories in a convenient place for future use.
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
1
SAFETY PROCEDURES
AND PRECAUTIONS
Knowledge of proper procedures is essential to the
safe operation of electrically and/or gas energized
equipment. In accordance with generally accepted
product safety labeling guidelines for potential
hazards, the following signal words and symbols
may be used throughout this manual.
DANGER
Used to indicate the presence of a
hazard that WILL cause severe
personal injury, death, or substantial
property damage if the warning
included with this symbol is ignored.
WA R N I N G
Used to indicate the presence of a
hazard that CAN cause personal injury,
possible death, or major property
damage if the warning included with
this symbol is ignored.
1. This appliance is intended to cook, hold or
process foods for the purpose of human
consumption. No other use for this appliance is
authorized or recommended.
2. This appliance is intended for use in commercial
establishments where all operators are familiar
with the purpose, limitations, and associated
hazards of this appliance. Operating
instructions and warnings must be read and
understood by all operators and users.
3. Any troubleshooting guides, component views,
and parts lists included in this manual are for
general reference only and are intended for use
by qualified technical personnel.
4. This manual should be considered a permanent
part of this appliance. This manual and all
supplied instructions, diagrams, schematics,
parts lists, notices, and labels must remain with
the appliance if the item is sold or moved to
another location.
CAUTION
Used to indicate the presence of a
hazard that can or will cause minor or
moderate personal injury or property
damage if the warning included with
this symbol is ignored.
CAUTION
NOTE
For equipment delivered for use
in any location regulated by the
following directive:
DO NOT DISPOSE OF ELECTRICAL
OR ELECTRONIC EQUIPMENT WITH
OTHER MUNICIPAL WASTE.
Used to indicate the presence of a hazard that can
or will cause minor personal injury, property
damage, or a potential unsafe practice if the
warning included with this symbol is ignored.
N O T E : Used to notify personnel of
installation, operation, or
maintenance information that is
important but not hazard related.
PG .
2
1000-TH-I
INSTALLATION / OPERATION / SERVICE MANUAL
I N S TA L L AT I O N
DANGER
CAUTION
IMPROPER INSTALLATION,
ALTERATION, ADJUSTMENT,
SERVICE, OR MAINTENANCE COULD
RESULT IN SEVERE INJURY, DEATH,
OR CAUSE PROPERTY DAMAGE.
READ THE INSTALLATION,
OPERATING AND MAINTENANCE
INSTRUCTIONS THOROUGHLY
BEFORE INSTALLING OR SERVICING
THIS EQUIPMENT.
METAL PARTS OF THIS EQUIPMENT
BECOME EXTREMELY HOT WHEN IN
OPERATION. TO AVOID BURNS,
ALWAYS USE HAND PROTECTION
WHEN OPERATING THIS APPLIANCE.
DANGER
DO NOT store or use gasoline or other
flammable vapors or liquids in the
vicinity of this or any other appliance.
CAUTION
TO PREVENT PERSONAL INJURY,
USE CAUTION WHEN MOVING OR
LEVELING THIS APPLIANCE.
S I T E I N S TA L L AT I O N
The Alto-Shaam cook
and hold oven must be
installed in a location
that will permit the
oven to function for its
intended purpose and
to allow adequate
clearance for
ventilation, proper
cleaning, and
maintenance access.
®
1. The oven must be installed on a stable and
level surface.
2. DO NOT install this oven in any area where it
may be affected by any adverse conditions such
as steam, grease, dripping water, high
temperatures, etc.
3. DO NOT store or use any flammable liquids or
allow flammable vapors in the vicinity of this
oven or any other appliance.
Emissions testing conducted by Underwriters
Laboratories, Inc. ® was found to be in
compliance with the applicable requirements of
NFPA96: 2004 Edition, Par. 4.1.1.2. U.L
emissions sampling of grease laden vapor
resulted in a total of 0.55 milligrams per cubic
meter with no visible smoke and is considered
representative of all oven models in the line.
Based on these results, hood installation and/or
outside venting should not be a requirement in
most areas. Verify local codes for locations
where more restrictive codes are applicable.
MINIMUM CLEARANCE REQUIREMENTS
COMBUSTIBLE
SURFACES
BACK
LEFT SIDE
RIGHT SIDE
TOP
3"
1"
1"
2"
(76mm)
(25mm)
(25mm)
(51mm)
NON - COMBUSTIBLE
SURFACES
3"
1"
1"
2"
(76mm)
(25mm)
(25mm)
(51mm)
4. This appliance must be kept free and clear of
any combustible materials.
5. This appliance must be kept free and clear of
any obstructions blocking access for
maintenance or service.
1000-TH-I
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
3
I N S TA L L AT I O N
S I T E I N S TA L L AT I O N
OPTIONS & ACCESSORIES
Bumper, Full Perimeter
5009767
PRIME RIB
STEAMSHIP ( CAFETERIA ) ROUND
72-3/4" (1847mm)
53-5/8" (1361mm)
with optional bumper
51-5/8" (1311mm)
Carving Holder,
Pass-Through
Design
Casters, 3-1/2” stem
(2 RIGID , 2 SWIVEL W / BRAKE )
5008017
Door Lock with Key
Drip Pan without Drain
1-7/8" (48mm)
LK-22567
DEPTH
Legs, 6" (152mm), Stemmed ( SET
Pan Grid, Wire 18"
26"
Rib Rack, Stainless Steel
32-1/4" (819mm)
15-1/4" (387mm)
Pass-Through
22-9/16" (573mm)
X
OF
PAN INSERT
4)
Security Panel w/Key Lock
Shelf, Stainless Steel, Flat Wire,
5011149
PN-2115
SH-2773
REACH - IN
SH-2325
SH-2346
72-15/16" (1852mm) to Electrical Connection
68-13/16" (1747mm)
7" (177mm)
11906
5011592
PASS - THROUGH
75-3/4" (1924mm) with 5" (127mm) Casters*
HL-2635
4459
20-1/2" (521mm)
24-1/8" (613mm)
25-1/16" (636mm)
with optional bumper
34-1/2" (876mm)
with optional bumper
*74-3/8" (1889mm) - with optional 3-1/2" (89mm) casters
*75-3/4" (1924mm) approx. - with optional 6" (152mm) legs
P R O D U C T \ P A N C A P A C I T Y (PER
120 lb (54 kg)
VOLUME MAXIMUM :
PG .
4
60
COMPARTMENT)
WEIGHT
(76
NET ( EST .)
MAXIMUM
QUARTS
LITERS )
1000-TH-I
SHIP ( EST .)
1000-TH-I/STD
1000-TH-I/HD
400 lb (181 kg)
440 lb (200 kg)
349 lb (159 kg)
INSTALLATION / OPERATION / SERVICE MANUAL
385 lb (175 kg)
I N S TA L L AT I O N
S I T E I N S TA L L AT I O N
A number of adjustments are associated with
initial installation and start-up. It is important
that these adjustments be conducted by a qualified
service technician. Installation and start-up
adjustments are the responsibility of the dealer or
user. These adjustments include but are not
limited to thermostat calibration, door adjustment,
leveling, electrical hook-up and installation of
optional casters or legs.
LEVELING
Level the oven
from side-to-side and front-toback with the use of a spirit level. For ovens
installed with casters, it is important that the
installation surface be level due to the probability
of frequent oven repositioning.
We recommend checking the level of the oven
periodically to make certain the floor has not
shifted nor the oven moved.
NOTE: Failure to properly level this oven can
cause improper function and will result in
the uneven baking with products
consisting of semi-liquid batter.
1000-TH-I
RESTRAINT REQUIREMENTS
—MOBILE EQUIPMENT
WA R N I N G
RISK OF ELECTRIC SHOCK.
Appliance must be secured
to building structure.
Any appliance that is not furnished with a power
supply cord but that includes a set of casters must
be installed with a tether. Adequate means must
be provided to limit the movement of this
appliance without depending on or transmitting
stress to the electrical conduit. The following
requirements apply:
1. Maximum height of casters is 6" (152mm).
2. Two of the casters must of be the locking type.
3. Such mobile appliances or appliances on mobile
stands must be installed with the use of a flexible
connector secured to the building structure.
A mounting connector for a restraining device is
located on the lower back flange of the appliance
chassis or on an oven stand, approximately 18"
(457mm) from the floor. A flexible connector is not
supplied by nor is it available from the factory.
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
5
I N S TA L L AT I O N
S I T E I N S TA L L AT I O N
DRIP TRAY INSTALLATION INSTRUCTIONS
Item
1.
2.
3.
4.
5.
FAILURE TO PROPERLY INSTALL THE
DRIP TRAY CAN OR WILL CAUSE
MAJOR EQUIPMENT DAMAGE AND
WILL RESULT IN A LEAKAGE
HAZARD THAT CAN CAUSE
PERSONAL INJURY.
6
1000-TH-I
INSTALLATION / OPERATION / SERVICE MANUAL
Qty
Double-Sided Tape
1
2
Drip Tray Holder
1
3
8-32 x 1/4" Phil Screw
3
4
Drip Tray
1
Poke holes through double-sided tape which is attached to the back of drip tray holder .
Remove backing on double-sided tape .
Put screws through holes and attach drip tray holder to unit.
Optional - apply a line of food-grade silicone caulk along top edge of drip tray holder to seal.
Place drip tray in drip tray holder .
WA R N I N G
PG .
Description
1
I N S TA L L AT I O N
ELECTRICAL CONNECTION
The appliance must be installed by a qualified
service technician. The oven must be properly
grounded in accordance with the National Electrical
Code and applicable local codes.
Plug the unit into a properly grounded receptacle
ONLY, positioning the unit so that the plug is
easily accessible in case of an emergency. Arcing
will occur when connecting or disconnecting the
unit unless all controls are in the “ OFF ” position.
Proper receptacle or outlet configuration or
permanent wiring for this unit must be installed by
a licensed electrician in accordance with applicable
local electrical codes.
With the voltage conversion switch in the 200-208V
(UPPER) position, the oven will function properly
with a source voltage of between 200 and 208.
All 125V rated units will function properly with a
source voltage of between 100 and 125, 60 Hz.
The 125V rated units are provided with a cord and
plug [NEMA #5-20P]. Have a licensed electrician
install the proper outlet configuration as required
for the unit in accordance with applicable, local
electrical codes. This will assure a safe and troublefree installation.
Ensure that the voltage conversion switch position
and the available power source match.
230V:
To prevent an electrical shock hazard between
the appliance and other appliances or metal parts
in close vicinity, an equalization-bonding stud is
provided. An equalization bonding lead must be
connected to this stud and the other appliances /
metal parts to provide sufficient protection
against potential difference. The terminal is
marked with the following symbol.
With the voltage conversion switch in the 220-240V
(LOWER) position, the unit will function properly
with a source voltage of between 220 and 240.
NOTE: ALL 208-240V units are shipped from the
factory with the voltage conversion switch
in the 220-240 position.
NOTE: 230V appliances must be connected to an
electrical circuit that is protected by an
external GFCI outlet.
DANGER
DANGER
ENSURE POWER SOURCE
MATCHES VOLTAGE STAMPED
To avoid electrical shock, this
appliance MUST be adequately
grounded in accordance with local
electrical codes or, in the absence of
local codes, with the current edition
of the National Electrical Code
ANSI/NFPA No. 70. In Canada, all
electrical connections are to be
made in according with CSA C22.1,
Canadian Electrical Code Part 1 or
local codes.
ELECTRICAL
VOLTAGE
208-240 (AGCY)
at 208
at 240
230 (AGCY)
PHASE
1
1
1
1
CYCLE / HZ
60
60
60
50
ON APPLIANCE NAMEPLATE.
DANGER
ELECTRICAL CONNECTIONS MUST
BE MADE BY A QUALIFIED SERVICE
TECHNICIAN IN ACCORDANCE WITH
APPLICABLE ELECTRICAL CODES.
AMPS
28.8
28.9
22.2
21.3
kW
6.0
6.0
5.3
4.9
CORD AND PLUG
NO CORD
OR PLUG
NO CORD OR PLUG
Wire diagrams are located inside the bonnet of the unit.
1000-TH-I
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
7
O P E R AT I N G I N S T R U C T I O N S
U S E R S A F E T Y I N F O R M AT I O N
CAUTION
METAL PARTS OF THIS EQUIPMENT
BECOME EXTREMELY HOT WHEN IN
OPERATION. TO AVOID BURNS,
ALWAYS USE HAND PROTECTION
WHEN OPERATING THIS APPLIANCE.
The Alto-Shaam cook and hold oven is intended
for use in commercial establishments by qualified
operating personnel where all operators are
familiar with the purpose, limitations, and
associated hazards of this appliance. Operating
instructions and warnings must be read and
understood by all operators and users.
S T A R T- U P O P E R A T I O N
BEFORE INITIAL USE:
Interior oven surfaces must be heated to remove
surface oils and the accompanying odor produced
during the first use of the oven.
1. Wipe all wire shelves, side racks and the full
oven interior with a clean, damp cloth. Install
the oven side racks, oven shelves, and external
drip tray. Shelves are installed with the curved
edge toward the back of the oven. Insert the
drip pan on the interior bottom surface of
the oven.
PREHEATING:
Always preheat the oven for a minimum of 45
minutes before cooking product. Follow the
operating instructions indicated on the next page
of this manual.
DANGER
2. Close the oven doors, press the power switch
to the on position, and set the thermostat to
300°F (149°C).
3. Allow the oven to cycle for approximately
2 hours or until no odor is detected.
AT NO TIME SHOULD THE INTERIOR
OR EXTERIOR BE STEAM CLEANED,
HOSED DOWN, OR FLOODED WITH
WATER OR LIQUID SOLUTION OF
ANY KIND. DO NOT USE WATER JET
TO CLEAN.
SEVERE DAMAGE OR
ELECTRICAL HAZARD
COULD RESULT.
WARRANTY BECOMES VOID IF
APPLIANCE IS FLOODED
DANGER
DISCONNECT UNIT FROM
POWER SOURCE BEFORE
CLEANING OR SERVICING.
PG .
8
1000-TH-I
INSTALLATION / OPERATION / SERVICE MANUAL
O P E R AT I N G I N S T R U C T I O N S
Holding Indicator
Light
Cooking Indicator
Light
I
o
Temperature
Gauge
Holding
Thermostat
Cooking
Thermostat
Cooking
Timer
ON/OFF
Power Switch
MANUAL CONTROL OPERATION:
COOKING OVEN CHARACTERISTICS:
1.
The oven is equipped with a special, high-heat-density,
heating cable. Through the Halo Heat concept, the
heating cable is mounted against the walls of the
cooking cavity to provide an evenly applied,
thermostatically controlled, heat source. The design
and operational characteristics of the oven eliminate
the need for a moisture pan or a heat circulating fan.
Through even heat application, the quality of a food
product is maintained for many hours.
I
o
Turn oven POWER SWITCH ‘ON’.
— POWER SWITCH will illuminate and
will remain lit as long as the Power
Switch is in the ‘ON’ position.
2.
Set the HOLD THERMOSTAT to the
required holding temperature.
3.
Set COOK THERMOSTAT to the required
cooking temperature.
4.
— HOLDING INDICATOR LIGHT will
illuminate as the Hold Thermostat calls
for heat. This process will continue as
long as the Power Switch and Hold
Thermostat are ‘ON’.
To preheat the oven, activate the Cook
Thermostat by turning the COOKING
TIMER clockwise.
DANGER
DISCONNECT UNIT FROM
POWER SOURCE BEFORE
CLEANING OR SERVICING.
— COOKING INDICATOR LIGHT and
HOLDING INDICATOR LIGHT will
illuminate as the unit calls for heat.
This process will continue until the
COOKING TIMER cycles to the
‘OFF’ position.
These instructions are basic operational guidelines only.
For complete instructions, see A Guide to Low
Temperature Cooking and Holding by HALO HEAT
packed with the oven.
1000-TH-I
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
9
O P E R AT I N G I N S T R U C T I O N S
General Holding Guideline
Chefs, cooks and other specialized food service
personnel employ varied methods of cooking.
Proper holding temperatures for a specific food
product must be based on the moisture content of
the product, product density, volume, and proper
serving temperatures. Safe holding temperatures
must also be correlated with palatability in
determining the length of holding time for a
specific product.
Halo Heat maintains the maximum amount of
product moisture content without the addition of
water, water vapor, or steam. Maintaining
maximum natural product moisture preserves the
natural flavor of the product and provides a more
genuine taste. In addition to product moisture
retention, the gentle properties of Halo Heat
maintain a consistent temperature throughout the
cabinet without the necessity of a heat distribution
fan, thereby preventing further moisture loss due to
evaporation or dehydration.
When product is removed from a high
temperature cooking environment for immediate
transfer into equipment with the lower temperature
required for hot food holding, condensation can
form on the outside of the product and on the inside
of plastic containers used in self-service
applications. Allowing the product to release the
initial steam and heat produced by high temperature
cooking can alleviate this condition. To preserve the
safety and quality of freshly cooked foods, however,
a maximum of 1 to 2 minutes must be the only time
period allowed for the initial heat to be released
from the product.
Most Halo Heat Holding Equipment is provided
with a thermostat control between 60° and 200°F
(16° to 93°C). If the unit is equipped with vents,
close the vents for moist holding and open the vents
for crisp holding.
PG .
10
1000-TH-I
H O L D I N G T E M P E R AT U R E R A N G E
MEAT
FAHRENHEIT
CELSIUS
BEEF ROAST — Rare
130°F
54°C
BEEF ROAST — Med/Well Done
155°F
68°C
BEEF BRISKET
160° — 175°F
71° — 79°C
CORN BEEF
160° — 175°F
71° — 79°C
PASTRAMI
160° — 175°F
71° — 79°C
PRIME RIB — Rare
STEAKS — Broiled/Fried
RIBS — Beef or Pork
130°F
54°C
140° — 160°F
60° — 71°C
160°F
71°C
VEAL
160° — 175°F
71° — 79°C
HAM
160° — 175°F
71° — 79°C
PORK
160° — 175°F
71° — 79°C
LAMB
160° — 175°F
71° — 79°C
CHICKEN — Fried/Baked
160° — 175°F
71° — 79°C
DUCK
160° — 175°F
71° — 79°C
TURKEY
160° — 175°F
71° — 79°C
GENERAL
160° — 175°F
71° — 79°C
FISH — Baked/Fried
160° — 175°F
71° — 79°C
LOBSTER
160° — 175°F
71° — 79°C
SHRIMP — Fried
160° — 175°F
71° — 79°C
120° — 140°F
49° — 60°C
160° — 175°F
71° — 79°C
80° — 100°F
27° — 38°C
EGGS —Fried
150° — 160°F
66° — 71°C
FROZEN ENTREES
160° — 175°F
71° — 79°C
HORS D'OEUVRES
160° — 180°F
71° — 82°C
PASTA
160° — 180°F
71° — 82°C
PIZZA
160° — 180°F
71° — 82°C
POULTRY
FISH/SEAFOOD
BAKED GOODS
BREADS/ROLLS
MISCELLANEOUS
CASSEROLES
DOUGH — Proofing
POTATOES
180°F
82°C
PLATED MEALS
140° — 165°F
60°— 74°C
SAUCES
140° — 200°F
60° — 93°C
SOUP
140° — 200°F
60° — 93°C
VEGETABLES
160° — 175°F
71° — 79°C
THE HOLDING TEMPERATURES LISTED ARE SUGGESTED
GUIDELINES ONLY. ALL FOOD HOLDING SHOULD BE BASED ON
INTERNAL PRODUCT TEMPERATURES . ALWAYS FOLLOW LOCAL
HEALTH ( HYGIENE ) REGULATIONS FOR ALL INTERNAL
TEMPERATURE REQUIREMENTS .
INSTALLATION / OPERATION / SERVICE MANUAL
CARE AND CLEANING
CLEANING AND PREVENTIVE MAINTENANCE
PROTECTING STAINLESS STEEL SURFACES
It is important to guard against
corrosion in the care of
stainless steel surfaces.
Harsh, corrosive, or
inappropriate chemicals can
completely destroy the
protective surface layer of stainless steel.
Abrasive pads, steel wool, or metal implements
will abrade surfaces causing damage to this
protective coating and will eventually result in
areas of corrosion. Even water, particularly hard
water that contains high to moderate
concentrations of chloride, will cause oxidation
and pitting that result in rust and corrosion. In
addition, many acidic foods spilled and left to
remain on metal surfaces are contributing factors
that will corrode surfaces.
Proper cleaning agents, materials, and
methods are vital to maintaining the appearance
and life of this appliance. Spilled foods should be
removed and the area wiped as soon as possible
but at the very least, a minimum of once a day.
Always thoroughly rinse surfaces after using a
cleaning agent and wipe standing water as quickly
as possible after rinsing.
CLEANING AGENTS
Use non-abrasive cleaning products designed for
use on stainless steel surfaces. Cleaning agents
must be chloride-free compounds and must not
contain quaternary salts. Never use hydrochloric
acid (muriatic acid) on stainless steel surfaces.
Always use the proper cleaning agent at the
manufacturer's recommended strength.
Contact your local cleaning supplier for
product recommendations.
CLEANING MATERIALS
The cleaning function can usually be accomplished
with the proper cleaning agent and a soft, clean
cloth. When more aggressive methods must be
employed, use a non-abrasive scouring pad on
difficult areas and make certain to scrub with the
visible grain of surface metal to avoid surface
scratches. Never use wire brushes, metal scouring
pads, or scrapers to remove food residue.
BRU
S
IRE
EL PA
STE
DS
NO
W
S
HE
NO
SCR APER
O
S
N
CAUTION
1000-TH-I
TO PROTECT STAINLESS STEEL
SURFACES, COMPLETELY AVOID
THE USE OF ABRASIVE CLEANING
COMPOUNDS, CHLORIDE BASED
CLEANERS, OR CLEANERS
CONTAINING QUATERNARY SALTS.
NEVER USE HYDROCHLORIC ACID
(MURIATIC ACID) ON STAINLESS
STEEL. NEVER USE WIRE
BRUSHES, METAL SCOURING
PADS OR SCRAPERS.
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
11
CARE AND CLEANING
EQUIPME NT CARE
Under normal circumstances, this
oven should provide you with long
and trouble free service. There is no
preventative maintenance required,
however, the following Equipment
Care Guide will maximize the potential life and
trouble free operation of this oven.
The cleanliness and appearance of this equipment
will contribute considerably to operating efficiency
and savory, appetizing food. Good equipment that
is kept clean works better and lasts longer.
CLEAN DAILY
1.
2.
3.
4.
Disconnect unit from power
source, and let cool.
Remove all detachable items
such as wire shelves, side racks,
and drip pans. Clean these
items separately.
6.
7.
9.
Remove excess water with sponge and wipe dry
with a clean cloth or air dry. Leave doors open
until interior is completely dry. Replace side racks
and shelves.
Wipe door gaskets and control panel dry with a
clean, soft cloth.
10. Interior can be wiped with a sanitizing solution
after cleaning and rinsing. This solution must
be approved for use on stainless steel food
contact surfaces.
11. To help maintain the protective film coating on
polished stainless steel, clean the exterior of the
cabinet with a cleaner recommended for stainless
steel surfaces. Spray the cleaning agent on a clean
cloth and wipe with the grain of the stainless steel.
12. Clean any glass with a window cleaner.
Wipe the interior metal surfaces of the oven with a
paper towel to remove loose food debris.
Clean the interior metal surfaces of the cabinet
with a damp clean cloth or sponge and any good
commercial detergent.
NOTE: Avoid the use of abrasive cleaning
compounds, chloride based cleaners, or
cleaners containing quaternary salts. Never
use hydrochloric acid (muriatic acid) on
stainless steel.
5.
8.
Spray heavily soiled areas with a water soluble
degreaser and let stand for 10 minutes, then
remove soil with a plastic scouring pad.
Wipe control panel, door vents, door handles, and
door gaskets thoroughly since these areas harbor
food debris.
Rinse surfaces by wiping with sponge and clean
warm water.
DANGER
DISCONNECT UNIT FROM
POWER SOURCE BEFORE
CLEANING OR SERVICING.
Always follow appropriate state or local health
(hygiene) regulations regarding all applicable cleaning
and sanitation requirements for equipment.
CLEAN THE DOOR VENTS
Door vents need to be inspected and cleaned
as required.
CHECK OVERALL CONDITION OF
OVEN ONCE A MONTH
Check the oven once a month for physical damage and
loose screws. Correct any problems before they begin
to interfere with the operation of the oven.
DANGER
AT NO TIME SHOULD THE INTERIOR
OR EXTERIOR BE STEAM CLEANED,
HOSED DOWN, OR FLOODED WITH
WATER OR LIQUID SOLUTION OF
ANY KIND. DO NOT USE WATER JET
TO CLEAN.
SEVERE DAMAGE OR
ELECTRICAL HAZARD
COULD RESULT.
WARRANTY BECOMES VOID IF
APPLIANCE IS FLOODED
DO NOT USE OVEN IF CONTROLS ARE NOT
PROPERLY FUNCTIONING
Refer to the Trouble Shooting Guide located in this
manual or call an authorized service technician.
PG .
12
1000-TH-I
INSTALLATION / OPERATION / SERVICE MANUAL
S A N I TAT I O N
Food flavor and aroma are usually so closely
related that it is difficult, if not impossible, to
separate them. There is also an important,
inseparable relationship between cleanliness and
food flavor. Cleanliness, top operating efficiency,
and appearance of equipment contribute
considerably to savory, appetizing foods.
Good equipment that is kept clean, works
better and lasts longer.
The most accurate method of measuring safe
temperatures of both hot and cold foods is by
internal product temperature. A quality
thermometer is an effective tool for this purpose,
and should be routinely used on all products that
require holding at a specific temperature.
A comprehensive sanitation program should focus
on the training of staff in basic sanitation
procedures. This includes personal hygiene,
proper handling of raw foods, cooking to a safe
internal product temperature, and the routine
monitoring of internal temperatures from receiving
through service.
Most food imparts its own particular aroma and
many foods also absorb existing odors.
Unfortunately, during this absorption there is no
distinction between GOOD and BAD odors. The
majority of objectionable flavors and odors
troubling food service operations are caused by
bacteria growth. Sourness, rancidity, mustiness,
stale or other OFF flavors are usually the result of
germ activity.
The easiest way to insure full, natural food flavor is
through comprehensive cleanliness. This means
good control of both visible soil (dirt) and invisible
soil (germs). A thorough approach to sanitation
will provide essential cleanliness. It will assure an
attractive appearance of equipment, along with
maximum efficiency and utility. More importantly,
a good sanitation program provides one of the key
elements in the prevention of food-borne illnesses.
A controlled holding environment for prepared
foods is just one of the important factors involved
in the prevention of food-borne illnesses.
Temperature monitoring and control during
receiving, storage, preparation, and the service of
foods are of equal importance.
Most food-borne illnesses can be prevented
through proper temperature control and a
comprehensive program of sanitation. Both these
factors are important to build quality service as the
foundation of customer satisfaction. Safe food
handling practices to prevent food-borne illness is
of critical importance to the health and safety of
your customers.
HACCP, an acronym for Hazard Analysis (at)
Critical Control Points, is a quality control program
of operating procedures to assure food integrity,
quality, and safety. Taking steps necessary to
augment food safety practices is both cost effective
and relatively simple. While HACCP guidelines go
far beyond the scope of this manual, additional
information is available by contacting:
CENTER FOR FOOD SAFETY AND APPLIED
NUTRITION FOOD AND DRUG ADMINISTRATION
1-888-SAFEFOOD
INTERNAL FOOD PRODUCT TEMPERATURES
HOT FOODS
DANGER ZONE
40° TO 140°F
(4° TO 60°C)
CRITICAL ZONE
70° TO 120°F
(21° TO 49°C)
SAFE ZONE
140° TO 165°F
(60° TO 74°C)
COLD FOODS
DANGER ZONE
SAFE ZONE
ABOVE 40°F
(ABOVE 4°C)
36° TO 40°F
(2° TO 4°C)
FROZEN FOODS
DANGER ZONE
ABOVE 32°F
(ABOVE 0°C)
CRITICAL ZONE
0° TO 32°F
(-18° TO 0°C)
SAFE ZONE
0°F or below
(-18°C or below)
1000-TH-I
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
13
SERVICE
THERMOSTAT/INDICATOR LIGHT SEQUENCE
Whenever the thermostat is turned “ON”, the
indicator light will indicate the power ON/OFF
condition of the heating cable, and consequently, the
cycling of the cabinet as it maintains the dialed cavity
temperature. If this light does not illuminate after
normal start-up, the main power source, thermostat,
and/or light must be checked. If the warming cabinet
does not hold the temperature as dialed, the
calibration of the thermostat must be checked. If the
warming cabinet fails to heat or heats continuously
with the thermostat “OFF”, the thermostat must be
initially checked for proper operation. If these items
are checked and found to be in order, a continuity and
resistance check of the heating cable should be made.
SEE CIRCUIT DIAGRAM.
DANGER
DISCONNECT UNIT FROM
POWER SOURCE BEFORE
CLEANING OR SERVICING.
THERMOSTAT CALIBRATION
The thermostat is precision calibrated at the factory.
Normally, no adjustment or recalibration is necessary
unless the thermostat has been mishandled in transit,
changed or abused while in service. A thermostat
with a sensing bulb operates on hydraulic pressure,
consequently, any bending of the bulb results in a
change in its volume, and alters the accuracy of the
thermostat calibration.
A thermostat should be checked or recalibrated by
placing a quality, thermal indicator at the center of an
empty holding cavity. DO NOT CALIBRATE WITH
ANY FOOD PRODUCT IN THE CABINET. The
thermostat should be set, and should be allowed to
stabilize at that setting for a minimum of one hour.
Following temperature stabilization, the center of the
thermal swing of the air temperature within the
cabinet should approximately coincide with the
thermostat setting.
If calibration is necessary, the calibration screw
should be adjusted with great care. The calibration
screw of the thermostat is located in the thermostat
dial shaft. With the shaft held stationary, a minute,
clockwise motion of the calibration screw appreciably
lowers the thermostat setting. A reverse, or counterclockwise motion appreciably raises the thermostat
setting. After achieving the desired cycling of the
thermostat, the calibration screw must be sealed.
Place a few drops of enamel sealant directly on the
calibration screw.
(Red nail polish or equivalent is acceptable.)
PG .
14
1000-TH-I
INSTALLATION / OPERATION / SERVICE MANUAL
SERVICE
TROUBLE SHOOTING CHECKLIST
TROUBLE
POSSIBLE CAUSE
REMEDY
Cooking temperature not correct.
Cook thermostat out of calibration.
Calibrate.
Unit does not operate.
Insufficient electric power unit.
Defective plug or cord.
Power switch defective.
Holding temperature not correct.
Timer runs down, but oven will not
go into HOLD.
Hold thermostat out of calibration.
Check power source.
Check and repair if necessary.
Replace.
Calibrate.
Timer not de-energizing cook circuit. Replace timer.
Cook thermostat erratic — will not
hold calibration.
Cook thermostat.
Replace thermostat.
Hold thermostat erratic — will not
hold calibration.
Hold thermostat.
Replace thermostat.
Oven goes from cooking
temperature to cold.
Hold thermostat.
Replace hold thermostat.
Oven will not go into cook cycle
when timer and cook thermostat
are ON.
Timer or contactor.
With timer turned ON, line
voltage should appear across
terminal 2 and 3 of timer. If not,
replace timer.
If line voltage does appear across
terminal 2 and 3 of timer, it should
also appear across holding coil
of contactor.
It takes too long to cook.
(Temperature O.K.)
Cannot control temperature but
thermostats check O.K.
Heating element open, resulting in
low wattage.
Heating element grounded.
If line voltage does appear across
holding coil, and it won’t close its
contacts, replace contactor.
Replace element.
Replace element.
DANGER
DISCONNECT UNIT FROM
POWER SOURCE BEFORE
CLEANING OR SERVICING.
1000-TH-I
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
15
SERVICE
1000-TH-I SERVICE VIEW - EXTERIOR
3
39
34
16
21
38
9
26
25
13
8
11
6
SECTION A-A
20
41
A
40
A
30
36
14
10
8
23
17
1
31
12
23
33
2
22
37
24
32
4
19
Part numbers and drawings are subject to change without notice.
PG .
16
1000-TH-I
INSTALLATION / OPERATION / SERVICE MANUAL
15
18
7
38
SERVICE
1 0 0 0 - T H - I PA R T S L I S T - E X T E R I O R
ITEM
DESCRIPTION
PART NO. QTY
ITEM
DESCRIPTION
PART NO. QTY
1
SHIM, HINGE
13947
2
22
GASKET ASSY, DOOR
GS-22952
2
2
SLAB DOOR ASSY.
15415
2
23
HANDLE, OFFSET MAG. LATCH
HD-27080
2
3
NON-SENSOR COVER
1005886
4
24
HINGE
HG-22338
2
4
CASTER SPACER
1007145
12
25
INSULATION
IN-2003
1
5
VENT PANEL*
1007351
1
26
RATING TAG LABEL
LA-26348
2
6
BACK CASING
1009940
1
27
NUT, M4-0.7 HEX 18-8*
NU-22286
2
7
BOTTOM PANEL
1009941
1
28
PLUG, 3/8" HOLE*
PG-25574
1
8
PANEL, SIDE, STD
1009942
2
29
RIVET, #42 STAINLESS*
RI-2097
10
9
BONNET, TOP COVER
1009951
1
30
RIVET, BLIND, #44, STNLS
RI-2100
12
10
DRIP PAN WELD ASSY*
5005616
2
31
SCREW, 10-32 X 3/4 PAN HD
SC-2071
4
11
CABLE INSULATION
5009203
1
32
SCREW,10-32 X 3/4,NF PHIL
SC-2072
12
12
CENTER PANEL
5009219
1
33
SCREW,10-32X1-1/2,NF,PHIL
SC-2073
20
13
BONNET ASSY, SPOT
5009223
1
34
8-32 X 5/8" PAN HD 4*
SC-2077
4
14
FAN MOUNT
5009253
1
35
SCREW,M4-0.7X6MM PHIL*
SC-22271
2
15
DRIP TRAY KIT
5009716
1
36
8-32 X 2 SLOT PAN HEAD 18-8 S.S.
SC-23154
2
16
BLOCK, CAP HOLD DOWN
BK-33844
4
37
SCREW,1/4-20 X 1/2,NC SLOT RND
SC-2332
4
17
BUSHING, SNAP
BU-3378
4
38
8-32 X 1/2" PHIL SCREW
SC-2425
16
18
CASTER, 5" RIGID
CS-24874
2
39
8-32 X 1/4" PHIL SCREW 24*
SC-2459
24
19
CASTER, 5" SWIVEL W/ BRAKE
CS-24875
2
40
SHELF, NICKEL CHROME
SH-2325
6
20
FAN, BOX
FA-34524
1
41
SIDE RACK, CHROME
SR-2266
4
21
CAPILLARY GUARD
GD-2450
2
42
TAPE, FOAM*
TA-25621
1
*NOT
SHOWN
CABLE HEATING SERVICE KIT - #4881
( ON E KIT P E R CA BIN E T COMP A RTME N T)
Includes:
CB-3045
CR-3226
IN-3488
BU-3105
BU-3106
SL-3063
TA-3540
ST-2439
NU-2215
Cable Heating Element . . . . . . . . . . .210 feet
Ring Connector . . . . . . . . . . . . . . . . . . . . . .12
Insulation Corner . . . . . . . . . . . . . . . . .1 foot
Shoulder Bushing . . . . . . . . . . . . . . . . . . . .12
Cup Bushing . . . . . . . . . . . . . . . . . . . . . . . .12
Insulating Sleeve . . . . . . . . . . . . . . . . . . . .12
Electrical Tape . . . . . . . . . . . . . . . . . . . .1 roll
Stud 10-32 . . . . . . . . . . . . . . . . . . . . . . . . . .12
Hex Nut 10-32 . . . . . . . . . . . . . . . . . . . . . . .24
1000-TH-I
DANGER
DISCONNECT UNIT FROM
POWER SOURCE BEFORE
CLEANING OR SERVICING.
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
17
SERVICE
1000-TH-I SERVICE VIEW - ELECTRICAL
5
36
5
20
1
34
32
13
38
31
3
7
26
25
30
28
15
29
21
40
24
39
8
27
12
17
16
18
14
23
37
35
33
Part numbers and drawings are subject to change without notice.
PG .
18
1000-TH-I
INSTALLATION / OPERATION / SERVICE MANUAL
SERVICE
1 0 0 0 - T H - I PA R T S L I S T - E L E C T R I C A L
ITEM
DESCRIPTION
1
SWITCH COVER
2
PART NO. QTY
ITEM
DESCRIPTION
PART NO. QTY
11133
1
21
M4-0.7 HEX NUT 18-8
NU-22286
2
BRKT, PILOT LIGHT MTG*
1004360
2
22
NUT, HEX #8-32*
NU-2296
4
3
HEAT SINK
1005836
1
23
CONTROL PANEL BEZEL
PE-26567
1
4
ACCESS COVER*
1009990
1
24
CONTROL PANEL OVERLAY
PE-26692
1
5
BONNET SPOT ASSEMBLY
5009188
1
25
PLUG, 3/8 HOLE
PG-25574
2
6
WIRE SET*
5009290
1
26
PLUG, 13/16 HOLE
PG-3589
2
7
T-BLOCK
BK-3019
1
27
10-32 X 3/4 PAN HD
SC-2071
4
8
TERMINAL BLOCK
BK-3023
2
28
10-32 X 1/4 PAN HD GROUND SCREW
SC-2190
1
9
BRACKET, TETHER*
BT-26884
1
29
SCREWS, M4-0.7X6MM PHIL
SC-22271
2
10
1/2" HOLE BUSHING*
BU-3006
2
30
8-32 X 2 SLOT PAN HEAD 18-8 S.S.
SC-23154
2
11
7/8" SNAP BUSHING*
BU-3007
1
31
6-32 X 1-1/4" ROUND HD
SC-2365
2
12
1 1/8" SNAP BUSHING
BU-3378
8
32
SCREW, 10-32X1/2, NF PHIL, FLAT
SC-23670
4
13
CONTACTOR 208/240V 3 POLE 25 A
CN-3052
2
33
8-32 X 1/4" PHIL SCREW
SC-2459
8
14
CONNECTOR,PUSH WIRE
CR-34056
1
34
SCREW, 8-32X1/2T-410PH PAN HD
SC-25849
8
15
FAN, 3" BOX, 230V
FA-34524
1
35
SWITCH, RKR, 20AMP, 250V, GREEN
SW-34769
1
16
1/2" SELF ADHESIVE GASKET
GS-2019
8
36
20A, TOGGLE SWITCH
SW-3528
1
17
GAUGE, TEMP, 100-400 DEG
GU-34197
1
37
TIMER, 12HR, 208-240V, 50/60HZ
TR-34542
1
18
KNOB, THERMOSTAT
KN-26568
3
38
THERMOSTAT, HOLD
TT-3057
1
19
WHITE PILOT LIGHT 250V*
LI-3951
2
39
THERMOSTAT, COOK
TT-3329
1
20
NUT, 10-32, NF HEX MS, #18-8 S/S
NU-2215
4
40
STAR LOCK WASHER
WS-2467
1
*NOT
SHOWN
DANGER
DISCONNECT UNIT FROM
POWER SOURCE BEFORE
CLEANING OR SERVICING.
1000-TH-I
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
19
PG .
20
1000-TH-I
INSTALLATION / OPERATION / SERVICE MANUAL
1000-TH-I
INSTALLATION / OPERATION / SERVICE MANUAL
PG .
21
T R A N S P O RTAT I O N D A M A G E a n d C L A I M S
All Alto-Shaam equipment is sold F.O.B. shipping point, and when accepted by the carrier, such shipments
become the property of the consignee.
Should damage occur in shipment, it is a matter between the carrier and the consignee. In such cases, the
carrier is assumed to be responsible for the safe delivery of the merchandise, unless negligence can be
established on the part of the shipper.
1. Make an immediate inspection while the equipment is still in the truck or immediately after it is moved to the receiving area.
Do not wait until after the material is moved to a storage area.
2. Do not sign a delivery receipt or a freight bill until you have made a proper count and inspection of all merchandise received.
3. Note all damage to packages directly on the carrier’s delivery receipt.
4. Make certain the driver signs this receipt. If he refuses to sign, make a notation of this refusal on the receipt.
5. If the driver refuses to allow inspection, write the following on the delivery receipt:
Driver refuses to allow inspection of containers for visible damage.
6. Telephone the carrier’s office immediately upon finding damage, and request an inspection. Mail a written confirmation of the time,
date, and the person called.
7. Save any packages and packing material for further inspection by the carrier.
8. Promptly file a written claim with the carrier and attach copies of all supporting paperwork.
We will continue our policy of assisting our customers in collecting claims which have been properly filed and actively pursued.
We cannot, however, file any damage claims for you, assume the responsibility of any claims, or accept deductions in payment
for such claims.
L I M I T E D WA R R A N T Y
Alto-Shaam, Inc. warrants to the original purchaser only that any original part that is found to be defective in material or workmanship will, at
Alto-Shaam's option, subject to provisions hereinafter stated, be replaced with a new or rebuilt part.
The parts warranty period is as follows:
For the refrigeration compressor on Alto-Shaam Quickchillers™, five (5) years from the date of installation.
For the heating element on Halo Heat® cook/hold ovens, as long as the original purchaser owns the oven.
For all other parts, one (1) year from the date of installation or fifteen (15) months from the shipping date, whichever occurs first.
The labor warranty period is one (1) year from the date of installation or fifteen (15) months from the shipping date, whichever occurs first.
Alto-Shaam will bear normal labor charges performed during standard business hours, excluding overtime, holiday rates or any
additional fees.
To be valid, a warranty claim must be asserted during the applicable warranty period. This warranty is not transferable.
THIS WARRANTY DOES NOT APPLY TO:
1. Calibration.
2. Replacement of light bulbs and/or the replacement of display case glass due to damage of any kind.
3. Equipment damage caused by accident, shipping, improper installation or alteration.
4. Equipment used under conditions of abuse, misuse, carelessness or abnormal conditions, including but not limited to, equipment subjected
to harsh or inappropriate chemicals, including but not limited to, compounds containing chloride or quaternary salts, poor water quality, or
equipment with missing or altered serial numbers.
5. Damage incurred as a direct result of poor water quality, inadequate maintenance of steam generators and/or surfaces affected by water
quality. Water quality and required maintenance of steam generating equipment is the responsibility of the owner/operator.
6. Damage caused by use of any cleaning agent other than Alto-Shaam's Combitherm® Cleaner, including but not limited to damage due to
chlorine or other harmful chemicals. Use of Alto-Shaam's Combitherm® Cleaner on Combitherm® ovens is highly recommended.
7. Any losses or damage resulting from malfunction, including loss of product or consequential or incidental damages of any kind.
8. Equipment modified in any manner from original model, substitution of parts other than factory authorized parts, removal of any parts
including legs, or addition of any parts.
This warranty is exclusive and is in lieu of all other warranties, express or implied, including the implied warranties of merchantability and
fitness for a particular purpose. In no event shall Alto-Shaam be liable for loss of use, loss of revenue or profit, or loss of product, or for any
indirect, special, incidental, or consequential damages. No person except an officer of Alto-Shaam, Inc. is authorized to modify this warranty
or to incur on behalf of Alto-Shaam any other obligation or liability in connection with Alto-Shaam equipment.
Effective 02/09
RECORD THE MODEL AND SERIAL NUMBER OF THE APPLIANCE FOR EASY REFERENCE.
ALWAYS REFER TO BOTH MODEL AND SERIAL NUMBER IN ANY CONTACT WITH ALTO-SHAAM REGARDING THIS APPLIANCE.
Model: _______________________________________________Date Installed: __________________________________________________________
Voltage: ______________________________________________ Purchased From: _______________________________________________
Serial Number: _______________________________________ _______________________________________________________________________
W164 N9221 Water Str eet
PHONE:
●
P. O . B o x 4 5 0
●
Menomonee Falls, Wisconsin 53052-0450
●
U.S.A.
262.251.3800 • 800.558-8744 USA/CANADA
FAX: 262.251.7067 • 800.329.8744 U.S.A. ONLY
www.alto-shaam.com
PRINTED IN U.S.A.