Canister Steam Cleaner

OWNER’S MANUAL

Model S3325H

120V., 60Hz., 1500 Watts

For information or assistance:

EURO-PRO Operating LLC

94 Main Mill Street, Door 16

Plattsburgh, NY 12901

Tel.: 800-798-7398

Model S3325H

1 YEAR LIMITED WARRANTY

Your Steam Cleaner is warranted to be free from defects in material and workmanship for a period of one (1) year from the date of purchase when utilized for normal household use by the original purchaser only. The included Warranty Registration Card must be filled out and returned within 10 days of purchase. This is essential for your Warranty to be effective should any problem arise with this product.

Should any defect covered by the terms of the limited warranty be discovered within one year,

EURO-PRO Operating LLC will repair or replace any defective part provided the unit is returned by the original purchaser, freight prepaid, to:

US: EURO-PRO Operating LLC , 94 Main Mill Street, Door 16, Plattsburgh, N.Y. 12901

Proof of purchase date and $12.95 for handling and return packing/shipping charges must be included.*

The liability of under this warranty is limited solely to the cost of the replacement parts or the complete unit at our option. LABOUR CHARGES ARE NOT INCLUDED.

This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes. This Limited Warranty does not cover damage caused by misuse, negligent handling, or damage due to faulty packaging or mishandling in transit

(by any common carrier).

This warranty is extended to the original purchaser of the unit and excludes all other legal and/or conventional warranties. The responsibility of EURO-PRO Operating LLC , if any, is limited to the specific obligations expressly assumed by it under the terms of the limited warranty. In no event is

EURO-PRO Operating LLC liable for incidental or consequential damages of any nature whatsoever. Some States/Provinces do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.

This warranty gives you specific legal rights which vary from state to state or province to province.

*Important: Carefully pack item to avoid damage in shipping. Be sure to attach tag to item before packing with your name, complete address and phone number with note giving purchase information, model number and what you believe is the problem with item. We recommend you insure the package (as damage in shipping is not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER SERVICE”. We are constantly striving to improve our products, therefore the specifications contained herein are subject to change without notice.

OWNERSHIP REGISTRATION CARD

Please complete and return within ten (10) days of purchase. The registration will enable us to contact you in the event a product defect is discovered. By returning this card you acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying instructions .

RETURN TO: EURO-PRO Operating LLC , 94 Main Mill Street, Door 16, Plattsburgh, N.Y. 12901

PURCHASER: ……………………………………..…………………………………………………

ADDRESS: ………………………………………...……………………………………………….

CITY: ……………………………….. STATE…………………………………………………….

NAME AND ADDRESS OF DEALER: …………………………………………………………..

Printed in China 13

USAGE SUGGESTIONS FOR THE STEAM CLEANER

Artificial Plants

Use the concentrator without a brush attached to blow off the dust and dirt.

Clothing

A vapor cleaning system is excellent for removing wrinkles from fabrics. Simply

“vaporize” the surface from a distance

(12”-18”)with the steam diffuser. The dry vapor removes wrinkles without leaving the fabric wet like ordinary fabric steamers do.

Nicotine and Tar

Nicotine and tar dissolves at high temperatures and becomes a light yellow oil that has the consistency of sewing machine oil. When the nicotine/tar film is touched by a hot terry cloth towel clipped over the floor brush, it immediately dissolves and flows into the towel. You can remove it from flat surfaces as fast as you can move the brush over the surface.

Removing Wax, Tar, Etc

.

Many stains are only stuck on the surface of materials and can be easily and quickly removed by “blowing” excess material away from the surface from the side. This is accomplished by using the concentrator. Hold the terry cloth towel to the side to catch the loose residue as it is blown by the concentrator. Note : Always vacuum any loose residue off the surface before you apply vapor to it.

Hints

ALWAYS FINISH CLEANING BY WIPING

DOWN THE CLEANED SURFACE WITH

A TOWEL

The steam cleaner has many uses that have not been mentioned. This was meant only to give you a general idea of what can be achieved with the unit. However, the ways in which to use the attachments and brushes are in most cases universal. It is most helpful to always have a terry cloth towel or paper towel ready to use for removal of moisture and residue.

100% white cotton towels work best.

You can clean the brushes with your steam cleaner. To clean the floor brush, hold at one end and use the concentrator to simply blow off dirt into the garbage can. When cleaning the detail brush, use a pair of pliers to hold and blow dirt as above or place in the basket of your dishwasher.

Note : Wipe with a towel immediately before the cleaned area dries. When cleaning the oven, use the detail brush to clean around the elements and drip trays. Use the detail brush for cracks, crevices, and hard to reach areas.

Refrigerator - Use the concentrator to blow away dirt in the ice machine and on door seals. The vapor will not dry out or crack the seals as chemicals often do. Can openers and other kitchen equipment can be easily cleaned with the detail brush to get into all the nooks and crannies. Mold stains around door gaskets can be removed with the detail brush.

To clean microwaves or other small appliances use the detail brush for small areas.

Note: When cleaning small electrical appliances always unplug them from outlet before cleaning.

To clean counter tops , use the floor brush with a terry cloth towel attached. For heavily soiled areas, use the brush without the terry cloth towel first in order to loosen the debris, then follow with a terry cloth towel attached to finish.

12

IMPORTANT SAFETY INSTRUCTIONS

When using your Canister Steam Cleaner , basic safety precautions should always be observed, including the following:

1.

Read all instructions before using your

Canister Steam Cleaner.

2.

Use the system only for its intended use.

3.

To protect against a risk of electric shock, do not immerse any part of the system in water or other liquids.

4.

This unit should always be turned “OFF” before plugging into or unplugging from electrical outlet. Never yank cord to disconnect from outlet; instead, grasp plug and pull to disconnect.

5.

Do not allow cord to touch hot surfaces.

Let the system cool completely before putting away or before opening the water tank (removing the safety cap) . Wrap power cord loosely around your system when storing.

6.

Always disconnect system from electrical outlet when filling or emptying water tank and when not in use. Always turn the safety cap slowly when opening the water tank.

This will allow any remaining steam to escape gradually.

7.

Do not operate the system with a damaged cord or plug, or if the appliance or any other part of the system has been dropped or damaged. To avoid the risk of electric shock, do not disassemble or attempt to repair the Canister Steam Cleaner.

Return the system to EURO-PRO

Operating LLC (see warranty) for examination and repair. Incorrect reassembly or repair can cause a risk of electrical shock or injury to persons when the steam cleaner is used.

8.

Close supervision is necessary for any appliance being used by or near children.

Do not leave the system unattended while connected.

9.

Burns can occur from touching hot parts, hot water or steam. Do not turn upside down as there may be hot water in the unit.

Never direct steam at any person. The steam is very hot and can cause burns.

10.

Do not operate in the presence of explosive and/or flammable fumes.

11. This appliance is intended only for household use. Follow all user instructions in this manual.

12. Never use any chemicals or substance other than tap water in the machine. Use of chemicals may damage the machine. Use of chemicals will automatically void your warranty.

To reduce the risk of fire, electric shock, or injury:

• Do not leave the Canister Steam Cleaner plugged in when unattended. Unplug the electrical cord when not in use and before servicing or refilling water tank.

• Do not allow unit to be used as a toy. Close attention is necessary when used by or near children, pets or plants.

• Use only as described in this manual. Use only manufacturer’s recommended accessories.

• When using the steam cleaner, please note that the force and the heat of the steam may damage certain surfaces or textiles. Always test on a small, concealed area of the material that you are steam cleaning. i.e. painted wood or leather can be bleached with hot steam; glossy plastic can be dulled, fabrics such as acrylic, velvet and linen can react sensitively to the temperature of the steam.

• Do not hold the steam jet concentrated for too long on a single spot.

• Do not pull cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Keep cord away from heated surfaces.

• Do not use extension cords or outlets with inadequate current carrying capacity.

• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• Do not handle plug or steam cleaner with wet hands or operate without shoes.

• Do not put any objects into openings. Do not use with any opening blocked.

• Store your appliance indoors in a cool, dry area.

• Keep your work area well lit.

• When in use, never turn the appliance over or on its side. Never direct steam towards people, animals or plants.

• Do not immerse the steam cleaner into water or other liquids. Always unplug the power cord from the electrical socket when filling the steam cleaner.

• Do NOT add cleaning solutions, scented perfumes, oils or any other chemicals to the water used in this appliance as this may damage the unit or make it unsafe for use.

Use regular tap water or distilled/purified water if the tap water in your area is very hard.

SAVE THESE INSTRUCTIONS

For Household Use Only

Rev. 11/03A

1

ADDITIONAL IMPORTANT SAFEGUARDS cont.

1. To avoid circuit overload, do not operate another appliance on the same socket

(circuit)

2. If an extension cord is absolutely necessary, a 15 ampere 14 gage cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange cord so that it cannot be pulled or tripped over.

3. Do not leave unattended when the system is connected to a power supply/electrical outlet.

SAVE THESE INSTRUCTIONS

FOR HOUSEHOLD USE ONLY

WARNING:

This appliance is equipped with a grounded-type 3-wire cord (3-prong plug).

This plug will only fit into an electrical outlet made for a 3-prong plug. This is a safety feature. If the plug should fail to fit the outlet, contact an electrician to replace the outlet. Do not attempt to defeat the safety purpose of the grounding pin, part of the 3-prong plug.

CAUTION:

The force and heat of the steam may adversely affect certain materials. Always check the suitability of using the steam cleaner on a surface by carrying out a preliminary test on a hidden area.

Examples for guidance only:- Varnished wood or glossy leather can be bleached by the effects of steam.

- Shiny plastic materials risk being tarnished.

- Acrylic, velvets and linen are very sensitive to the temperature of steam.

The manufacturer accepts no responsibility for damage caused to objects, materials, animals or persons due to the inappropriate use of steam, and through ignoring the advice and recommendations set down in the Owner's Manual.

USAGE SUGGESTIONS FOR THE STEAM CLEANER

Window, Glass Surfaces & Mirrors

Use the window squeegee. Work with the vapor jet on using the top to bottom movements. Use the squeegee with the vapor off to clear the water from the glass.

To do this without leaving streaks, use lateral movements from the top to the bottom of the surface.

Fiberglass or Stainless Steel

Surfaces

Use the floor brush or brass detail brush.

Slowly move the brush over the surface to be cleaned. The vapor will emulsify the dirt and grease on the surface. Follow behind with a terry cloth towel over the brush to remove excess moisture and residue.

Tip : An old idea for polishing stainless steel is to wipe it down with seltzer soda water after it is cleaned.

Soap Scum

Soap scum dissolves almost immediately under a combination of heat and moisture. Rinse the surface with a small amount of water afterwards or go back over it once more with a clean terry cloth towel.

Note: Soap scum sometimes will develop a hard surface from waterborne minerals.

If this is the case, use the floor brush with no towel first to break up this surface - or spray or wipe first with lemon, vinegar or seltzer soda water to soften the minerals.

Moving too slowly can dry out the soap scum and cause it to granulate on the surface. The surface will have a gritty feel. If this happens, apply vapor to the surface with the open brush again and reclean.

Blinds

Use the nylon detail brush to clean blinds.

Move the brush over the surface, allowing enough time for the vapor to penetrate.

Work quickly on PVC blinds. Test for color fastness on fabric blinds before using. Finish by wiping with a towel.

Bathroom Areas

To clean the bathtub or shower area, use the detail brush for grout, shower door tracks, hard to get areas and heavily soiled areas. The window squeegee will be the most efficient way to clean the rest of the area. Allow plenty of time for the heat to penetrate the surface. This is especially helpful in the shower area if there is tile or grout. Wipe with towel.

Removal of soap scum on tile, grout, and shower doors is also easier with the steam cleaner

To clean sanitary fixtures, use the concentrator nozzle with or without nylon detail brush. Use a terry cloth towel or paper towel to wipe up excess moisture and residue.

To clean the sink and faucets, use nylon detail brush then finish by wiping with a towel.

11

2

USAGE SUGGESTIONS FOR THE STEAM CLEANER

Wood, Vinyl and Marble Floors

Use the floor brush with a terry cloth attached. Move the brush across the floor as if you are mopping. When the towel is soiled, allow to cool, then turn the towel over or replace it with a clean towel. If you are working on a very dirty area, you can move the brush over the area slowly, several times. If it is a wood floor, move fast to avoid heat or moisture buildup in the wood. By cleaning with the towel over the brush, you will not affect the shine on the floor.

To Strip Wax : Use floor brush for open areas; detail brush for corners or tight areas - no towel, slow strokes. Work a small area at a time - remove the emulsified wax from the floor. When all of the wax has been stripped, immediately clean the floor and brushes with water before residue has a chance to harden on them. Go back over the stripped area with the floor brush with a towel to remove any remaining residue before waxing.

To Clean Waxed Floors: Wrap clean towel around the floor brush, brush quickly. This will cause the dirt to be removed but not the wax.

Vinyl Floors: Do not allow heat to buildup in any kind of vinyl, since it can soften it enough to affect its texture. Work fast on vinyl.

Tile Floors: Use the concentrator with the nylon detail brush attached to an extension. Have the floor brush with cloth attached ready as well. Clean the grout between the tiles with the detail brush.

Remove the detail brush and attach the floor brush, move the brush across the floor to clean the tile and remove excess moisture and residue. For areas of tile that are very dirty, remove the towel and agitate with the brush. Do not let the area dry before you wipe with a towel.

Spot Cleaning (Carpets)

Use the concentrator with or without the nylon detail brush. Move slowly over the soiled area, allowing the steam to penetrate. Agitate with detail brush or clean towel. Dab the spot with the towel

(do not rub). Repeat as necessary to remove stain. Vacuum only after the carpet has completely dried.

Always test color fastness of carpet in an inconspicuous area before cleaning.

If your steam cleaner fails to remove stubborn stains a commercially available carpet shampoo may be required.

Do NOT add cleaning solutions, scented perfumes, oils or any other chemicals to the water used in this appliance as this may damage the unit or make it unsafe for use.

Upholstery

Use the floor brush attached directly to the hand grip with a clean white terry cloth towel. Use fast, light strokes, avoid getting the fabric wet. Be patient with stubborn spots; work on a spot gently for no more than a minute at a time, then wait five minutes for the area to dry and repeat. Use circular movements or back-and-forth and sideto-side movements to get all sides of surface fibers then blot with a towel.

Finish with a brushing in one direction that will give the fabric a uniform appearance.

CAUTION:

Always determine the color-fastness of any fabric-especially with reds or blues - by taking a clean, moist, warm towel and gently rubbing a small area as far down on the back or other out of the way place on the furniture as possible. If color comes off on the towel, you may need to have the piece dry cleaned.

10

GETTING TO KNOW YOUR CANISTER STEAM CLEANER

1.

On/Off Switch

2.

Heating Light (Red)

3.

Steam Ready Light

4.

Water Tank Safety Cap

5.

Carrying Handle

6.

Transparent Accessory

Compartment

7.

Extension Tubes (x2)

8.

Latch Release Button

9.

Floor Brush Angle Adapter

10. 6-ft Flexible Steam Hose

11. Hose Hand Grip

12. On/Off Steam Switch

13. Floor Brush

14. Towel Clamps

15. Carpet/Floor Selector

16. Large Brass Bristle Brush

17. Small Nylon Bristle Brush

18. Angle Concentrator

19. Window Squeegee

20. Steam Diffuser

21. Accessory Adapter

22. Concentrator Nozzle

23. Towel For Floor Brush

24. Steam Diffuser Bonnet

25. Measuring Cup

26. Funnel

27. Parking System

28. Replacement O-Rings

(x3)

Technical Specifications

Voltage:

Power:

120V., 60Hz.

1500 Watts

Water Capacity: 47 U.S. Fl. Oz. (1400 ml)

Steam Generator: Stainless Steel

IMPORTANT: Before assembling the steam cleaner for the first time, make sure to remove any protective film from the accessory and hose ends.

3

FEATURES

Your Canister Steam Cleaner utilizes pressurized steam to remove tough grease,dirt and grime.

Steam is nature’s purest and most powerful cleaner for safely cleaning all hard surfaces in your home without harsh chemicals, thus being perfectly ecological. The appliance has various attachments so that it can be used for many purposes such as:

1. Clean upholstery, sealed grout, bathroom/kitchen tile, stovetops.

2. Easy to clean difficult to reach areas with the angle adapter or concentrator such as faucets, etc.

3. Ideal for windows, mirrors, glass doors, etc.

4. Clean fabrics, window coverings, pillows, bedding etc.

5. Clean hard surface areas such as counters, sinks, shower door tracks, etc.

WARNING:

When using your canister steam cleaner, the force and the heat of the steam may damage certain surfaces or textiles. Your Canister Steam Cleaner is designed to clean hard surfaces and upholstery that will withstand high heat. Do not use on soft plastics, unsealed wood and cold glass. On surfaces that have been treated with wax or some no wax floors, the sheen may be removed by the heat and steam action. Do not use on unsealed wood. This could cause the wood grain to rise. Fabrics such as acrylic, velvet and linen can react sensitively to the temperature of the steam. It is therefore recommended to test an isolated area of the surface to be cleaned before proceeding.

CAUTION:

Do not plug in the machine during filling. Use a grounded receptacle. Use only a heavy duty extension cord rated for 15 amps - Do not use an ordinary extension cord.

IMPORTANT:

Do NOT add cleaning solutions, scented perfumes, oils or any other chemicals to the water used in this appliance.

Use regular water or distilled/purified water if the tap water in your area is very hard.

Your Canister Steam Cleaner has the following features:

On/Off Button: To turn the unit “On” or “Off”, depress the ON/OFF button. When turned

“On”, the boiler will start to produce steam.

Heating Light (red): This light will illuminate when the unit is plugged into the wall outlet and will remain on until the unit is unplugged.

Steam Ready Light: When this light will illuminate, it indicates that the steam is ready to use.

On/Off Steam Switch : Press the steam switch on the hose hand grip to the “On” position to start the flow of steam.

Safety Cap : Always press the safety cap down and turn counter clockwise to open or clockwise to close and tighten.

4

Care & Maintenance

CAUTION: This appliance must be unplugged from the electrical outlet and allowed to cool down before performing any cleaning or maintenance tasks on the unit.

A periodic rinse of your steam cleaner will free it from deposits. This is recommended every 10-15 tankfulls to free up any scale deposits. Fill the boiler with water and shake vigorously. Tilt the cleaner upside down to empty the boiler of water and any scale deposits.

If you consistently use demineralized or distilled water, cleaning the tank is unnecessary.

Descaling your steam cleaner:

If the tap water in you area contains a high level of calcium deposits and you have been using tap water to do your steam cleaning, you should descale your unit after

10-15 tankfulls.

Step 1: Unplug the steam cleaner from the power source before you descale the boiler. Allow to cool.

Step 2: Fill the boiler with 1 part vinegar and 5 parts water and leave overnight or for a period of approximately 8 hours. Do not screw the safety/filler cap onto the steam cleaner while you are descaling the boiler.

Do not use the steam cleaner while descaling solution is inside the boiler.

Step 3: After the period of soaking, turn the steam cleaner upside down to empty solution from the boiler.

Due to the fact that a small amount of solution will be left in the boiler, it is necessary to rinse the boiler out with clean water 2 or

3 times. Your steam cleaner is now ready for use.

OPERATING INSTRUCTIONS

Tips On How To Use Your System

Water

• Use tap water for all your cleaning needs.

• However, if you live in an area with hard water, use de-mineralized / distilled water when steaming light colored fabrics to eliminate the possibility of hard water stains.

IMPORTANT:

Do NOT add cleaning solutions, scented perfumes, oils or any other chemicals to the water used in this appliance. Use tap water or distilled/purified water if the tap water in your area is very hard.

WARNING

: A towel wrapped around the brush can become hot enough to burn. Make sure that you let the towel cool off for

5 minutes before touching it.

Using Towels

• For best results use 100% cotton white terry cloth towels.

• Use correct size of towel to allow you to wrap the towel around the brushes and clip it under the spring loaded cloth holder.

• The purpose of using a towel is to absorb moisture and dirt being removed. Always use dry towels.

A wet towel will smear the dirt.

• Wash towels with strong detergent and bleach.

• Using scented fabric softener while washing the towels will cause the scent to be released into the air when using the towels with your steam system.

Efficient Work

• For vertical surfaces, wipe with a towel from the top down, in this way the dirty water will not soil surfaces already cleaned.

• Avoid changing brushes back and forth while cleaning.

• Start with the smallest brush to clean tight spots and corners first.

• Use a towel to wipe dirt as soon as possible, otherwise it will dry and re-adhere to the surface.

9

OPERATING INSTRUCTIONS

CAUTION: This appliance must be unplugged from the electrical outlet and allowed to cool down for 15 minutes before attaching or removing any accessory on the unit.

Using the Nylon Detail Brush

The nylon detail brush attaches to the accessory adapter and is best for cleaning the grout between tiles, ceramic or marble surfaces. Clean porcelain sinks, tubs, small spots, blinds, small appliances.

Using the Brass Detail Brush

The large brass brush attaches to the accessory adaptor and is best for cleaning ovens, stainless steel sinks and hard metal surfaces such as cast iron

BBQ’s.

Using the Angle Concentrator

The angle concentrator attaches to the accessory adaptor and is best for cleaning in tight areas such as around bathroom fixtures, door tracks or under toilet bowl rims.

Using the Steam Diffuser

Attach the steam diffuser to the accessory adaptor. You can use this attachment with or without the window squeegee.

Use the steam diffuser with the bonnet for cleaning upholstery. Use fast, light strokes, avoid getting the fabric wet. Be patient with stubborn spots; work on a spot gently for no more than a minute at a time, then wait five minutes for the area to dry and repeat. Use circular movements or back-and-forth and side-to-side movements to get all sides of surface fibers. Finish with a brushing in one direction that will give the fabric a uniform appearance. (Fig. 12)

Using the Window Squeegee

To attach the window squeegee to the steam diffuser,place the two hinges at the back of the window squeegee (see illustration) into the two open tabs that are at the back of the steam diffuser.

Swing the window squeegee up against the bottom of the steam diffuser until the locking tab engages. (Fig. 13)

Fig. 13

CAUTION : When cleaning windows, always avoid any sudden changes in temperature to prevent glass breakage or cracks.

To use the window squeegee, work with the vapor jet down using the top to bottom movements. To do this without leaving streaks, use lateral movements from the top to the bottom of the surface.

The window squeegee is also perfect for cleaning mirrors, ceramic tiles and shower doors.

Using the Parking Position

Please note that your steam cleaner can be conveniently placed in a space saving parking position.

When you are finished using the steam cleaner, slide the hook that is on the rear of the floor brush into the slot that is located on the rear of the steam cleaner.

(Fig. 14)

Fig. 12

Caution: Always determine the color-fastness of any fabric especially with reds or blues by taking a clean, moist, warm towel and gently rubbing a small area as far down on the back or other out of the way place on the furniture as possible. If color comes off on the towel, you may need to have the piece dry cleaned.

8

Fig. 14

OPERATING INSTRUCTIONS

Filling your Canister Steam Cleaner with Water

IMPORTANT:

Always insure that the unit is “UNPLUGGED” from the wall receptacle and all switches are in the “Off” position prior to initial filling or re-filling the water tank. Never attempt to fill this unit under a water tap , always use the filling flask and funnel provided.

Failure to follow these steps will cause the water tank to overfill and may pose an electrical safety hazard.

RECOMMENDATION

: The use of distilled/demineralized water is recommended particularly in areas with hard water in order to prevent the build-up of limescale.

Step 1: Make sure that the canister steam cleaner is NOT plugged into an electrical wall outlet.

Step 2: Press the safety cap down and turn counter clockwise until removed.

Step 3: Add 47 fl. oz (1400 ml) of water using the filling flask and funnel provided. (Fig. 1) Do not overfill. Replace Safety

Cap by turning clockwise press down firmly to tighten.

Heating time is approximately

10-12 minutes. Filling the boiler with hot water will shorten heat up time.

Step 4: Connect the desired accessory onto the steam hose.

Step 5: Plug the unit into a standard

120 volt wall receptacle. Press the On/Off switch. The Heating light (Red) will light up.

Step 6: Allow approximately 10-12 minutes for water vapor to reach its working temperature.

When unit is ready for use the steam ready light will light up.

Step 7: Upon initial use, some water will come out from the hose nozzle. This is residual water that is left over in the hose from the last use and is normal.

CAUTION: Always point the nozzle outlet in a safe direction. Never point in the direction of yourself, other people or pets.

Fig. 1

NOTE:

When the steam cleaner has run out of water, steam output will cease.

WARNING: Always allow the unit to cool for 15 minutes before re-filling. When refilling the steam cleaner while it is still hot, the first drops of water might bubble up. Use caution when opening the safety cap as cap may become hot during use and escaping steam can cause scalding.

Refilling Unit With Water

Step 1: Press the On/Off button on the unit to the “Off” position.

Step 2: Press the On/Off steam switch to the “On” position and wait until no more steam comes out of the hose.

Step 3: Remove the plug from the electrical outlet and allow the unit to cool for approximately

15 minutes before refilling with water.

Step 4: After the unit has cooled for

15 minutes, carefully press down on the safety cap and turn counter clockwise to loosen. Any residual steam will be released below the safety cap if the tank has not been completely vented.

When the hissing stops and the last steam has been released, remove the safety cap.

5

OPERATING INSTRUCTIONS

Step 5: Slowly pour water using the filling flask and funnel provided into the boiler. DO

NOT Fill Under a faucet , use the filling flask provided. DO NOT

OVERFILL . Never put more than 47 ounces (1400 ml) of water in the unit at one time.

Step 6: Screw safety cap back on to the unit by turning clockwise and press down to tighten securely. Plug appliance back into wall outlet. Steam will start to be produced as before.

Using Your Steam Cleaner with

Floor Brush

Step 1: Attach the two extension tubes to each other by pushing one onto the other making sure that they lock into place.

(Fig. 2)

Step 3

:

Attach the floor brush with the angle adapter on to the extension tubes.

Step 4: Attach the assembled extension tubes to the nozzle on the hose hand grip. Make sure that the locking button snaps in place.

Step 5: Insert the electrical power cord into the wall outlet.

Press the On/Off button on the unit to the “On” position.

The steam cleaner will now begin to produce steam.

Heating time is approx. 10-

15 minutes with cold water.

Filling the steam generator with hot water will shorten the heat up time. When the steam is ready, the steam ready light will light up.

Floor Brush

The floor brush is equipped with a carpet/floor selector. Turn the carpet/floor selector button to the right to raise the brush core to steam bare floors or walls with towel in place.

Turn the carpet/floor selector button to the left to release the brush core to steam clean carpets or hard to clean stains by using the bristles. (Fig. 4)

Fig. 2

Step 2: To attach the floor brush angle adapter to the floor brush, hold the floor brush with its bristles down in your left hand. With the floor brush angle adapter pointing downward, insert it into the hole in the back of the floor brush, then turn the floor brush angle adapter 180° counter clockwise. (Fig. 3)

Fig. 4

Note: The floor brush may be used with or without the towel.

Fig. 3

6

OPERATING INSTRUCTIONS

Attaching a Towel to the Floor

Brush

100% white terry cloth towel can be fitted on this brush, so as to absorb the dirt and protect delicate surfaces.

Important:

Please note that bristles may break through thin towels. To cut and make your own towels, we recommend that you use one (1) towel 8” x 17” folded in half or two (2) towels 4” x 17” laid one on top of the other be used. This will ensure that the brush bristles do not break through and that the towels will be sufficiently absorbent and retain as much dirt as possible.

Very Important

: When installing the towels to the floor brush, ensure that the towels do not cover the front and the back of the brush. (See Fig. 7)

In order to improve cleaning the floors with the steam cleaner and leave the floor drier, observe the following instructions:

1. Lay the towel flat on the floor.

2. Place the floor brush, centered on the towel. (Fig. 5)

3. Fold the ends of the towel and clamp ends under the towel clamps on the floor brush. The above is easily accomplished if the floor brush is removed from the extension tubes.

(Fig. 6)

4. Clip the other side of the towel under the other towel clamp as shown in

Fig. 7. When attaching the towel, leave some slack. Do not pull tightly around the brush.

5. Place the floor attachment on the floor. Wait until the towel is hot, then push slowly forward to clean the floor.

Most of the floor cleaning should be done with the slow, forward movement of the floor attachment.

Important Note:

After using the towel for some time the towel may become very

HOT. Care should be taken when changing the towel. Wait until the towel has cooled before changing it. Squeeze the towel to take out the accumulated water. Rinse in warm water or change the towel completely.

Washing Instructions

Machine wash in warm, soapy water using a mild detergent. If heavily soiled, you may want to use bleach in the washing machine.

Air dry ONLY . Do NOT dry in dryer.

Attaching the Accessory Adapter

To, attach the accessory adapter to the connection nozzle on the hose hand grip, push it in as far as it will go until you hear it click in place. To remove the accessory adapter, press on the locking button to release it. (Fig. 8)

Locking Button

Fig. 8

Attaching the Concentrator Nozzle

To, attach the concentrator nozzle to the accessory adapter, push it in as far as it will go and turn it to the left to lock in place. (Fig. 9)

The accessories (brushes, steam diffuser with or without window squeegee) can now be attached onto the concentrator nozzle or it can be used alone. (Fig. 10,

Fig. 11)

Fig. 9

Fig. 10

Fig. 5

Fig. 6

Fig. 7

Fig. 11

7