Avalue ARC-15W33 15.6” WXGA LCD Quick Reference Guide

ARC-15W33

15.6" Intel® Pentium®/Celeron®/Atom™ SoC Processor

Apollo Lake Fanless Rugged Touch Panel PC with IET

Expansion

Quick Reference Guide

3 rd

Ed

– 13 August 2020

Copyright Notice

Copyright



2020 Avalue Technology Inc., ALL RIGHTS RESERVED.

Part No. E2017A530A2R

ARC-15W33

FCC Statement

THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS

SUBJECT TO THE FOLLOWING TWO CONDITIONS:

(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE.

(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING

INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS

FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.

THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST

HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A

COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN

RADIATE RADIO FREQUENCY ENERGY AND, IF NOT INSTATLLED AND USED IN

ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL

INTERFERENCE TO RADIO COMMUNICATIONS.

OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE

HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO

CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.

A Message to the Customer

Avalue Customer Services

Each and every Avalue’s product is built to the most exacting specifications to ensure reliable performance in the harsh and demanding conditions typical of industrial environments. Whether your new Avalue device is destined for the laboratory or the factory floor, you can be assured that your product will provide the reliability and ease of operation for which the name Avalue has come to be known.

Your satisfaction is our primary concern. Here is a guide to A value’s customer services. To ensure you get the full benefit of our services, please follow the instructions below carefully.

Technical Support

We want you to get the maximum performance from your products. So if you run into technical difficulties, we are here to help. For the most frequently asked questions, you can easily find answers in your product documentation. These answers are normally a lot more detailed than the ones we can give over the phone. So please consult the user’s manual first.

To rec eive the latest version of the user’s manual; please visit our Web site at: http://www.avalue.com.tw/

2 ARC-15W33 Quick Reference Guide


Content

1.

Getting Started ........................................................................................................ 7

1.1

Safety Precautions .................................................................................................... 7

1.2

Packing List ............................................................................................................... 7

1.3

System Specifications ............................................................................................... 8

1.4

System Overview .................................................................................................... 12

1.4.1

I/O View ................................................................................................................................. 12

1.5

System Dimensions ................................................................................................ 13

2.

Hardware Configuration ....................................................................................... 14

2.1

ARC-15W33 connector mapping............................................................................. 15

2.1.1

Serial port 1 connector (COM1) ............................................................................................. 15

2.1.2

Serial port 2 connector (COM2) ............................................................................................. 15

2.2

Installing Hard Disk & Memory ................................................................................ 16

2.3

Installing ARC-BYT DB ........................................................................................... 18

2.4

ARC-APL Overviews ............................................................................................... 20

2.5

ARC-APL Jumper and Connector list ...................................................................... 21

2.6

ARC-APL Jumpers & Connectors settings .............................................................. 23

2.6.1

Clear CMOS (JBAT1) ............................................................................................................ 23

2.6.2

Serial port 1/2 pin9 signal select (JRI1/JRI2) ........................................................................ 23

2.6.3

PWM Level select (JPWM_SEL1) ......................................................................................... 24

2.6.4

AT/ATX Input power select (JAT1) ........................................................................................ 24

2.6.5

Serial port 1 in RS-232/422/485 mode (JCOM_SEL1).......................................................... 25

2.6.6

LCD Inverter connector (JBKL1) ........................................................................................... 25

2.6.7

On-board header for USB2.0 (JUSB1) .................................................................................. 26

2.6.8

On-board header for USB2.0 (JUSB2) .................................................................................. 26

2.6.9

Battery connector (JBAT1) .................................................................................................... 27

2.6.10

LCD backlight brightness adjustment (JVR_BTN1) .............................................................. 27

2.6.11

LVDS connector (LVDS1) ...................................................................................................... 28

2.6.12

AMPLIFIER_R (JSPR1) ........................................................................................................ 29

2.6.13

AMPLIFIER_L (JSPL1) .......................................................................................................... 29

2.6.14

BIOS SPI connector (BIOS_SPI1)......................................................................................... 30

2.6.15

EC Debug connector (JEC1) ................................................................................................. 30

2.6.16

B2B connector (JB2B1) ......................................................................................................... 31

2.6.17

Touch panel connector (JTP1) .............................................................................................. 32

2.6.18

SATA Power connector (SATA_PWR1) ................................................................................ 32

ARC-15W33 Quick Reference Guide 3

ARC-15W33

2.6.19

FPC connector (JFPC1) ........................................................................................................ 33

2.6.20

Battery connector (JUPS1) .................................................................................................... 33

2.6.21

Power Button (JBTN1) ........................................................................................................... 34

2.6.22

Miscellaneous setting connector (JFP1) ............................................................................... 34

2.6.23

LED Board connector (JLED1) .............................................................................................. 35

2.6.24

Low pin count connector (JLPC1) ......................................................................................... 35

2.6.25

Power connector (PWR1) ...................................................................................................... 36

2.7

ARC-BYT DB-A/B/C/D/E/F/G/H/K Overviews ......................................................... 37

2.7.1

ARC-BYT DB-A ..................................................................................................................... 37

2.7.2

ARC-BYT DB-B ..................................................................................................................... 37

2.7.3

ARC-BYT DB-C ..................................................................................................................... 37

2.7.4

ARC-BYT DB-D ..................................................................................................................... 38

2.7.5

ARC-BYT DB-E ..................................................................................................................... 38

2.7.6

ARC-BYT DB-F ...................................................................................................................... 38

2.7.7

ARC-BYT DB-G ..................................................................................................................... 39

2.7.8

ARC-BYT DB-H ..................................................................................................................... 39

2.7.9

ARC-BYT DB-K ..................................................................................................................... 39

2.8

ARC-BYT DB-A/B/C/D/E/F/G/H/K Connector list .................................................... 40

2.8.1

ARC-BYT DB-A ..................................................................................................................... 40

2.8.2

ARC-BYT DB-B ..................................................................................................................... 40

2.8.3

ARC-BYT DB-C ..................................................................................................................... 40

2.8.4

ARC-BYT DB-D ..................................................................................................................... 40

2.8.5

ARC-BYT DB-E ..................................................................................................................... 40

2.8.6

ARC-BYT DB-F ...................................................................................................................... 41

2.8.7

ARC-BYT DB-G ..................................................................................................................... 41

2.8.8

ARC-BYT DB-H ..................................................................................................................... 41

2.8.9

ARC-BYT DB-K ..................................................................................................................... 41

2.9

ARC-BYT DB-D Connectors settings ...................................................................... 43

2.9.1

Serial Port 1 connector (D_COM1)........................................................................................ 43

2.9.2

Serial Port 2 connector (D_COM2)........................................................................................ 43

2.10

ARC-BYT DB-E Jumpers & Connectors settings .................................................... 44

2.10.1

CAN2.0 Switch (E_JCAN20) ................................................................................................. 44

2.10.2

For user update FW (E_JBOOT0) ......................................................................................... 44

2.10.3

For user update FW (E_JIAP1) ............................................................................................. 45

2.11

ARC-BYT DB-F Connectors settings ...................................................................... 47

2.12

ARC-BYT DB-G Connectors settings ...................................................................... 48

2.12.1

Serial Port 1 connector (G_COM1) ....................................................................................... 48

2.12.2


2.12.3


2.13

ARC-BYT DB-H Jumpers settings ........................................................................... 49



2.13.1

USB Power selector (H_USB_PWR_SEL1) .......................................................................... 49

2.14

ARC-BYT DB-H Connectors settings ...................................................................... 50

2.14.1

Serial Port 1 connector (H_COM1)........................................................................................ 50

2.14.2

Serial Port 2 connector (H_COM2)........................................................................................ 50

2.15

ARC-BYT DB-K Connectors settings ...................................................................... 51

2.15.1

Serial Port 1 connector (I_COM1) ......................................................................................... 51

2.15.2

Serial Port 2 connector (I_COM2) ......................................................................................... 51

3.BIOS Setup .................................................................................................................... 52

3.1

Introduction ............................................................................................................. 53

3.2

Starting Setup ......................................................................................................... 53

3.3

Using Setup ............................................................................................................ 54

3.4

Getting Help ............................................................................................................ 55

3.5

In Case of Problems ................................................................................................ 55

3.6

BIOS setup .............................................................................................................. 56

3.6.1

Main Menu ............................................................................................................................. 56

3.6.1.1

System Language ............................................................................................................................ 57

3.6.1.2

System Date .................................................................................................................................... 57

3.6.1.3

System Time .................................................................................................................................... 57

3.6.2

Advanced Menu ..................................................................................................................... 57

3.6.2.1

Trusted Computing .......................................................................................................................... 58

3.6.2.2

APCI Settings .................................................................................................................................. 58

3.6.2.3

IT8528 Super IO Configuration ........................................................................................................ 60

3.6.2.3.1

Serial Port 1 Configuration ............................................................................................................... 61

3.6.2.3.2


3.6.2.3.3


3.6.2.3.4


3.6.2.3.5


3.6.2.4

H/W Monitor ..................................................................................................................................... 63

3.6.2.5

S5 RTC Wake Settings .................................................................................................................... 64

3.6.2.6

Serial Port Console Redirection ....................................................................................................... 64

3.6.2.6.1

Legacy Console Redirection Settings .............................................................................................. 65

3.6.2.7

CPU Configuration ........................................................................................................................... 65

3.6.2.7.1

Socket 0 CPU Information ............................................................................................................... 66

3.6.2.7.2

CPU Power Management Configuration .......................................................................................... 66

3.6.2.8

Network Stack Configuration ........................................................................................................... 67

3.6.2.9

CSM Configuration........................................................................................................................... 68

3.6.2.10

NVMe Configuration ......................................................................................................................... 68

3.6.2.11

USB Configuration ........................................................................................................................... 69

3.6.2.12

Security Configuration ...................................................................................................................... 70

3.6.3

Chipset ................................................................................................................................. 70


ARC-15W33

3.6.3.1

North Bridge ................................................................................................................................... 71

3.6.3.2

South Bridge .................................................................................................................................. 72

3.6.3.3

Uncore Configuration ..................................................................................................................... 72

3.6.3.4

South Cluster Configuration ........................................................................................................... 74

3.6.3.4.1 HD-Audio Configuration .................................................................................................. 74

3.6.3.4.2 PCI Express Configuration .............................................................................................. 75

3.6.3.4.2.1 PCI Express Root Port 3 .......................................................................................... 75




3.6.3.4.4 SATA Drives .................................................................................................................... 79

3.6.3.4.3 USB Configuration........................................................................................................... 80

3.6.4

Security ................................................................................................................................ 80

3.6.4.1

Secure Boot menu ........................................................................................................................... 81

3.6.5

Boot ...................................................................................................................................... 82

3.6.6

Save and exit ....................................................................................................................... 83

3.6.6.1

Save Changes and Reset ................................................................................................................ 83

3.6.6.2

Discard Changes and Reset ............................................................................................................ 83

3.6.6.3

Restore Defaults .............................................................................................................................. 84

3.6.6.4

Launch EFI Shell from filesystem device ......................................................................................... 84



1. Getting Started

1.1 Safety Precautions

Warning!

Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis.

Caution!

Always ground yourself to remove any static charge before touching the CPU card. Modern electronic devices are very sensitive to static electric charges. As a safety precaution, use a grounding wrist strap at all times. Place all electronic components in a static-dissipative surface or static-shielded bag when they are not in the chassis.

1.2 Packing List

 1 x ARC-15W33 Panel PC













1 x Power Adapter

4 x screws for VESA

4 x screws for HDD

10 x screws for Wall Mount

10 x brackets for Wall Mount

10 x plastics spacer for Wall Mount


ARC-15W33

1.3 System Specifications

Component

Mother Board ARC-APL

CPU Onboard Intel® Celeron® N3350 SoC BGA Processor

CPU Cooler(Type) Fanless Heatsink

One 204-pin DDR3L SODIMM Socket, Supports Up to 8GB DDR3L 1600MTs

Memory

SDRAM

Power Supply

Adapter

Speaker

DC in

60W power adaptor

2 W*2

Wireless LAN

Bluetooth

Optional USB or MPCIe module

Optional

Operating System Ubuntu, Windows 10

Compatible to all ARC-BYT DB modules (BIOS auto adjusted)

Expansion Card

Expandable interface (1 x DP, 1 x PCIex1, 4 x USB, 1 x LPC, 1 x Audio (line in, line out, mic in)

2 x mini-PCIe Socket

Storage

Hard Disk Drive 1 x 2.5” Drive Bay (HDD/SSD either one)

Solid State Drive 1 x 2.5” Drive Bay (HDD/SSD either one)

Other Storage Device

1 x mSATA supports on the 1st Mini PCIe slot, Auto switch for mSATA or Mini

PCIe

Panel

LCD Panel 15.6", 1366 x 768

B/L Inverter/Converter LCD built in

Touch Screen P-cap (E968X000130R/Henghao HD-T156WP05-F4SB)

Touch Controller EETI

External I/O

1 x DB-9 COM1 (RS-232/422/485, selectable by BIOS & JUPMER, RS-485

Serial Port supports Auto Flow, Pin-9 selected by Ring/+5V/+12V)

1 x DB-9 COM2 (RS-232, Pin-9 selected by Ring/+5V/+12V)

USB Port

Video Port

4 x USB3.0 (2 x Double deck)

1 x HDMI (by ARC-BYT DB-C)

Audio Port Realtek ALC892 HD codec

LAN Port 2 x Intel I211AT GbE controller

Wireless LAN Antenna 3 x Antenna

Indicator Light HDD LED, Power LED (Green for Power, Yellow for HDD)



Expansion Slots

1 x mini PCIe full size (support half size)

1 x mSATA supports on the 1st Mini PCIe slot, Auto switch for mSATA or Mini

PCIe

Internal I/O

1 x SATA connector & 1 x 2-pin wafer SATA power connector

1 x 5-pin lockable connector for inverter backlight control with dimming

(PWM/DC mode & backlight brightness selected by BIOS as standard)

2 x 3-pin header for LCD backlight brightness adjustment (dimming)

1 x 3-pin header for CMOS (protect*Clear)

1 x 2 x 3-pin header for COM1/ 2 pin 9 signal selection (+5, +12, Ring, selected by jumper)

1 x 2 x 5-pin header for LPC (for test)

1 x 2 x 4-Pin header for SPI

1 x 2 x 5-pin wafer for front panel

1 x 3-pin for Power mode (AT/ATX)

1 x Buzzer

2 x 2-pin wafer for speaker out

1 x 1 x 5-pin 90 degree pin header for touch connector

1 x 1 x 5 pin wafer for 1 USB 2.0 (For USB WiFi)

1 x 8 pin FPC for SM bus

1 x 2 x 40-pin board to board connector for Expansion board

(Hirose FX18-80P-0.8SH & FX18-80S-0.8SH)

Mechanical

Power Type AT/ATX

DC +9V ~ +36V, wide voltage single power input

Power Requirement TVS component for surge protection

Reverse current/voltage protection

ACPI

Power Connector

Type

Dimension

Weight

Color

Fanless

OS Support

Reliability

Single power ATX Support S0, S3, S4, S5 and ACPI 3.0 Compliant

2.5mm Lockable DC Jack

391.2 x 239.2 x 57.5 mm

3.7 Kgs

Front: Die-Casting with Cover lens; Rear: Black Casting-Aluminum

Yes

Linux, Ubuntu, Windows 10

EMI Test CE/ FCC class B

Dust and Rain Test Front Panel IP65, Rear IP41 except I/O

Vibration Test Random Vibration Operation:

1. PSD: 0.00454G²/Hz , 1.5 Grms


ARC-15W33

Mechanical Shock

Test

2. operation mode

3. Test Frequency : 5-500Hz

4. Test Axis : X,Y and Z axis

5. 30 minutes per each axis

6. IEC 60068-2-64 Test:Fh

7. Storage : CF or SSD

Sine Vibration test (Non-operation)

1 Test Acceleration : 2G

2 Test frequency : 5~500 Hz

3 Sweep ： 1 Oct/ per one minute. (logarithmic)

4 Test Axis : X,Y and Z axis

5 Test time :30 min. each axis

6 System condition : Non-Operating mode

7. Reference IEC 60068-2-6 Testing procedures

Package vibration test

1. PSD: 0.026G²/Hz , 2.16 Grms

2. Non-operation mode

3. Test Frequency : 5-500Hz

4. Test Axis : X,Y and Z axis

5. 30 min. per each axis

6. IEC 60068-2-64 Test:Fh

1. Wave form ： Half Sine wave

2. Acceleration Rate ： 20g for operation mode

3. Duration Time ： 11ms

4. No. of Shock ： +/- X,Y,Z axis 3 times

5. Test Axis: +/- X,Y,Z axis

6. Operation mode

7. Reference IEC 60068-2-27 Testing procedures Test Eb : Shock Test

Package drop test

Drop Test 1 One corner , three edges, six faces

2 ISTA 2A, IEC-60068-2-32 Test:Ed

Operating

Temperature

-10 ~ +50 degree C

Operating Humidity 0 ~ 90% Relative Humidity, Non-condensing

Storage Temperature -20 ~ 60 degree

Compliant with following Flexible

Expansion Modules


ARC-BYT DB-A 4 x USB3.0 module

ARC-BYT DB-B 3 x Audio Jack (Line in/Line out/Mic in)+HDMI

ARC-BYT DB-C HDMI + Mini PCIe (w/ SIM slot)

ARC-BYT DB-D 2 x COM Isolation module

ARC-BYT DB-G 3 x COM (w/o isolation, RS-232 only)

ARC-BYT DB-H 2COM (RS-232) + 1USB 2.0

ARC-BYT DB-K 2COM (RS-232) + 1LAN

ARC-BYT DB-E 12-bit GPIO+CAN Bus

ARC-BYT DB-F CAN Bus for OBDII


Note: Specifications are subject to change without notice.


ARC-15W33

1.4 System Overview

1.4.1 I/O View

Connectors

Label Function

DC-IN DC Power-in connector

COM1/2 Serial port 1/2 connector

USB

LAN1/2

4 x USB 3.0 connector

RJ-45 Ethernet 1/2

LED HDD/Power LED indicator

Power Switch Power on button

Note

Default: Lockable DC Jack

Option: Phoenix Connector(MOQ apply)

DB-9 male connector


1.5 System Dimensions


(Unit: mm)


ARC-15W33

2. Hardware

Configuration

For advanced information, please refer to:

1- ARC-APL, ARC-BYT DB-A/B/C/D/E/F/G/H/K included in this manual.

Note: If you need more information, please visit our website: http://www.avalue.com.tw



2.1 ARC-15W33 connector mapping

2.1.1 Serial port 1 connector (COM1)

Signal

DATA-

DATA+

NC

RS-485

PIN PIN

1 6

2 7

3 8

Signal

NC

NC

NC

NC

GND

4 9

5

NC

Please set BIOS & JCOM1_SEL1

Signal

NDCDA#

NRXDA

NTXDA

NDTRA#

GND

RS-232

PIN PIN

1 6

2 7

3 8

4 9

5

Signal

NDSRA#

NRTSA#

NCTSA#

NRIA#

Signal

TxD-

TxD+

RxD+

RxD-

GND

RS-422

PIN PIN

1 6

2 7

3 8

4 9

5

Signal

NC

NC

NC

NC

Please set BIOS & JCOM1_SEL1

2.1.2 Serial port 2 connector (COM2)

Signal

NDCDB#

NRXDB

NTXDB

NDTRB#

GND

PIN PIN

1 6

2 7

3 8

4 9

5

Signal

NDSRB#

NRTSB#

NCTSB#

NRIB#


ARC-15W33

2.2 Installing Hard Disk & Memory

Step 1.

Memory Installation: Remove 3 screws to release the chassis cover, and remove it.

Step 2.1

Insert the SODIMM into the memory socket.

Step 2.2 Re-assemble your system back through previous steps to complete the installation.



Step 3.

HDD Installation: Insert the HDD into the Drive Bay and fasten 2 screws.


ARC-15W33

2.3 Installing ARC-BYT DB

Step 1.

Unfasten 2 screws of the HDD bracket and take it off.

Step 2.

Remove 4 screws to release the chassis cover, and remove it.



Step 2.1

Insert the ARC-BYT DB into the socket and fasten 3 screws.

Step 2.2 Re-assemble your system back through previous steps to complete the installation


ARC-15W33

2.4 ARC-APL Overviews



2.5 ARC-APL Jumper and Connector list

Jumper

Label

JBAT1

JRI1/2

JCOM_SEL1

Function Note

3 x 1 header, pitch 2.00mm Clear CMOS

Serial port 1/2 pin9 signal select 3 x 2 header, pitch 2.00mm

Serial port 1 in RS-232/422/485 mode 4 x 3 header, pitch 2.00mm

JPWM_SEL1

JAT1

Connectors

Label

PWM Level select

AT/ATX Input power select

3 x 1 header, pitch 2.00mm


Note

SO_DIMM1

Function

1 x 204-Pin DDR3L 1866MHz

SO-DIMM

JFP1

JLPC1

JBKL1

COM1/2

JTP1

JSPR1

JSPL1

JB2B1

JVR_BTN1

LED1

JLED1

LVDS1

USB1/2

JUSB1

JUSB2

ULAN1/2

MPCIE1

BT1

PWR1

Miscellaneous setting connector

Low pin count connector

5 x 2 wafer, pitch 2.00 mm

5 x 2 header, pitch 2.00 mm

LCD Inverter connector

Serial Port 1/2 connector

Touch panel connector

5 x 1 wafer, pitch 2.00mm

Matching Connector: JST

PHR-5

D-sub 9 pin, male


AMPLIFIER_R

AMPLIFIER_L

B2B connector




LCD backlight brightness adjustment 3 x 2 header, pitch 2.00mm

HDD/Power LED indicator

LED Board connector

LVDS connector


DIN 40-pin wafer, pitch 1.25mm

Matching Connector: Hirose

DF13-40DS-1.25C

USB connector 1/2

On-board header for USB2.0

On-board header for USB2.0

RJ-45 Ethernet 1/2



Mini-PCIe connector

Battery connector

Power connector



ARC-15W33

BIOS_SPI1

JEC1

BIOS SPI header

EC Debug connector

SATA1 Serial ATA connector

SATA_PWR1 SATA Power connector

JFPC1

JUPS1

FPC connector

Battery connector

JBTN1 Power Button








2.6 ARC-APL Jumpers & Connectors settings

2.6.1 Clear CMOS (JBAT1)


Protect*

Clear CMOS

*Default

2.6.2 Serial port 1/2 pin9 signal select (JRI1/JRI2)

Ring*

+12V

+5V

JRI2

* Default

JRI1


ARC-15W33

2.6.3 PWM Level select (JPWM_SEL1)

* Default

2.6.4 AT/ATX Input power select (JAT1)

* Default


ATX*

AT

+3.3V*

+5V


2.6.5 Serial port 1 in RS-232/422/485 mode (JCOM_SEL1)

RS232* RS422 RS485

PIN Signal PIN Signal PIN Signal

1 NDCDA# 2 COM1-1 3 485_422TX1-

4 NTXDA 5 COM1-3 6 422RX1+

7 NRXDA 8 COM1-2 9 485_422TX1+

10 NDTRA# 11 COM1-4 12

Note:

422RX1-

This connector is available after modify the mode of COM1 in

BIOS setting.

* Default

2.6.6 LCD Inverter connector (JBKL1)

Signal

+5V

VBRIGHT

BKLEN

GND

+12V

3

2

1

PIN

5

4


ARC-15W33

2.6.7 On-board header for USB2.0 (JUSB1)

2.6.8 On-board header for USB2.0 (JUSB2)

Signal

+5VSB

USB_R_DN6

USB_R_DP6

GND

GND

PIN

1

4

5

2

3

Signal

+5VSB

USB_CA_PN7

PIN

1

2

USB_CA_PP7

GND

GND

3

4

5



2.6.9 Battery connector (JBAT1)

2.6.10 LCD backlight brightness adjustment (JVR_BTN1)

Signal

+RTCBATT

GND

PIN

1

2

PIN Signal Note

1-2 BLK_VR_MOD VR must select 10K/1%

3-4 BLK_BRI_UP

5-6 BLK_BRI_DN

Low pulse button for backlight brighter

Low pulse button for backlight dim


ARC-15W33

2.6.11 LVDS connector (LVDS1)


Signal

+5V

+5V

PIN PIN

2 1

4 3

Signal

+3.3V

+3.3V

NC

GND

6

8

5

7

NC

GND

LVDS_DATA0_P 10 9 LVDS_DATA1_P

LVDS_DATA0_N 12 11 LVDS_DATA1_N

GND 14 13 GND



GND 20 19 GND



GND 26 25 GND



GND 32 31 GND

LVDS_CLK1_P 34 33 LVDS_CLK2_P

LVDS_CLK1_N 36 35 LVDS_CLK2_N

GND 38 37 GND

+12V 40 39 +12V


2.6.12 AMPLIFIER_R (JSPR1)

Signal

SPK_R-

SPK_R+

PIN

2

1

2.6.13 AMPLIFIER_L (JSPL1)

Signal

SPK_L-

SPK_L+

PIN

2

1


ARC-15W33

2.6.14 BIOS SPI connector (BIOS_SPI1)

2.6.15 EC Debug connector (JEC1)

Signal

+1.8VSB

SPI_CS#0

SPI_MISO

SPI_HOLD#

PIN PIN

1 2

3 4

5 6

7

Signal

GND

SPI_CLK

SPI_MOSI


Signal PIN

EC_SMCLK_DEBUG 1

EC_SMDAT_DEBUG 2


2.6.16 B2B connector (JB2B1)

Signal

GND

GND

+12V

+12V

GND

PIN PIN Signal

1 41 GND

2 42 GND

3 43 GND

4

5

44

45

GND

GND

LPC_SERIRQ 6 46 +5VSB

LPC_FRAME# 7 47 +5VSB

LPC_IET_CLK1 8 48 +5VSB

LPC_AD0 9 49 +5VSB

LPC_AD1 10 50 +5VSB

Signal

LPC_AD2

LPC_AD3

PS_ON_B2B

PIN PIN

11 51

12 52

13 53

PLT_RST_BUF# 14 54

PCH_SLP_S3# 15 55

HDMI_HPD_CONN 16 56

GND 17 57

Signal

GND

USB_DP_4

USB_DN_4

GND

SMB_SCL_S5

SMB_SDA_S5

GND

HDMI_DDC_CLK 18 58 NC

HDMI_DDC_DAT 19 59 PCIEUSB3_PONRSTB

GND

HDMI_TX_N2

20

21

60 PCIEUSB3_SMIB_INT#

61 PCIE_WAKE#_3

HDMI_TX_P2

GND

HDMI_TX_N1

HDMI_TX_P1

22 62

24 64

25 65

PLT_RST_BUF#

23 63 PCIE_CLKREQ#_3

GND

PCIE_TXN_3

GND

HDMI_TX_N0

HDMI_TX_P0

GND

HDMI_CLKN

HDMI_CLKP

GND

GND

26 66

27 67

28 68

29 69

30 70

31 71

32 72

33 73

MIC1-R-IN

MIC1-L-IN

GND

FRONT-JD

34 74

35 75

36 76

37 77

FRONT-R-OUT 38 78

FRONT-L-OUT 39 79

GND 40 80

PCIE_TXP_3

GND

PCIE_RXN_3

PCIE_RXP_3

GND

CLK_PCIE_N3

CLK_PCIE_P3

GND

GND

MIC1_JD

GND

LINE1-JD

LINE1-R-IN

LNE1-L-IN

GND


ARC-15W33

2.6.17 Touch panel connector (JTP1)

2.6.18 SATA Power connector (SATA_PWR1)

Signal

X+

X-

SENSE

Y+

Y-

PIN

1

2

3

4

5

Signal

GND

+5V

PIN

1

2


2.6.19 FPC connector (JFPC1)

2.6.20 Battery connector (JUPS1)


Signal

+5VSB

+3.3VSB

EC_SMDAT 6

NC 5

PIN

8

7

EC_SMCLK

AUX_INT1#

+5VSB

GND

4

3

2

1

Signal PIN PIN Signal

AC_PRESENT2 3 1 AC_PRESENT1

SMB_DSA_S0 4 2 SMB_SCL_S0


ARC-15W33

2.6.21 Power Button (JBTN1)

Signal

BUTTON

GND

PIN

1

2

2.6.22 Miscellaneous setting connector (JFP1)


Signal

+3.3VSB

VOL_UP#

BRI_UP#

PIN PIN

2

4

6

1

3

5

Signal

GND

VOL_DN#

BRI_DN#

LED_ONOFF# 8 7 PWR_BTN_IN_EC#

POWER_LED2 10 9 POWER_LED1

2.6.23 LED Board connector (JLED1)


Signal

+5VSB

LUMEN_EN

GND

PIN

1

2

3

2.6.24 Low pin count connector (JLPC1)

Signal

LPC_AD0

LPC_AD1

LPC_AD2

PIN PIN

1

3

5

2

4

6

Signal

+3.3V

PLT_RST_BUF#

LPC_FRAME#

LPC_AD3 7 8 LPC_PORT80_CLK

LPC_SERIRQ 9 10 GND


ARC-15W33

2.6.25 Power connector (PWR1)


*Option: Phoenix Connector

Signal

+DCIN

GND

PIN

1

2

2.7 ARC-BYT DB-A/B/C/D/E/F/G/H/K Overviews

2.7.1 ARC-BYT DB-A


2.7.2 ARC-BYT DB-B

2.7.3 ARC-BYT DB-C


ARC-15W33

2.7.4 ARC-BYT DB-D

2.7.5 ARC-BYT DB-E

2.7.6 ARC-BYT DB-F



2.7.7 ARC-BYT DB-G

2.7.8 ARC-BYT DB-H

2.7.9 ARC-BYT DB-K


ARC-15W33

2.8 ARC-BYT DB-A/B/C/D/E/F/G/H/K Connector list

2.8.1 ARC-BYT DB-A

Connectors

Label Function

A_JUSB1~4 USB3.0 connector 1~4

A_JB2B1 B2B connector

2.8.2 ARC-BYT DB-B

Connectors

Label Function

B_LINE_OUT1 Line-out audio jack

B_LINE_IN1 Line-in audio jack

B_MIC_IN1 Mic-in audio jack

B_JHDMI1 HDMI connector

B_JB2B1 B2B connector

2.8.3 ARC-BYT DB-C

Connectors

Label Function

C_JPCIE1

C_JSIM1

Mini PCI Express connector

SIM card slot (Push-push)

C_JHDMI1 HDMI connector

C_JB2B1 B2B connector

2.8.4 ARC-BYT DB-D

Connectors

Label Function

D_COM1/2

D_JB2B1


B2B connector

2.8.5 ARC-BYT DB-E

Jumpers

Label Function

E_JCAN20

E_JIAP1

CAN2.0 Switch

For user update FW

Note

Note

Note

Note

DB-9 male connector

Note





3 x 1 header, pitch 2.00mm E_JBOOT0 For user update FW

Connectors

Label Function

E_GPIO1

E_CN1

E_CAN1

E_JB2B1

General purpose I/O connector

For user update FW

CAN Bus connector

B2B connector

2.8.6 ARC-BYT DB-F

Connectors

Label Function

F_CAN1

F_CAN2

CAN Bus connector 1

CAN Bus connector 2

F_JB2B1 B2B connector

2.8.7 ARC-BYT DB-G

Connectors

Label Function

G_COM1/2/3 Serial Port 1/2/3 connector

G_JB2B1 B2B connector

2.8.8 ARC-BYT DB-H

Jumpers

Label Function

H_USB_PWR_SEL1 USB Power selector

Connectors

Label Function

H_JUSB1 USB3.0 connector

H_COM1/2 Serial Port 1/2 connector

H_JB2B1 B2B connector

2.8.9 ARC-BYT DB-K

Connectors

Label Function

Note

14 x 1 terminal, pitch 2.50mm


3 x 1 terminal, pitch 2.50mm

Note

Note


Note

DB-9 male connector


Note

DB-9 male connector

Note


ARC-15W33

I_JLAN1

I_COM1/2

I_JB2B1

RJ-45 Ethernet


B2B connector


DB-9 male connector


2.9 ARC-BYT DB-D Connectors settings

2.9.1 Serial Port 1 connector (D_COM1)

Signal

NDCD#_3_D

NRXD_3_D

NTXD_3_D

NDTR#_3_D

GND

PIN PIN Signal

1 6 NDSR#_3_D

2 7 NRTS#_3_D

3 8 NCTS#_3_D

4 9 NRI#_3_D

5

2.9.2 Serial Port 2 connector (D_COM2)

Signal

NDCD#_2_D

NRXD_2_D

NTXD_2_D

NDTR#_2_D

GND

PIN PIN Signal

1 6 NDSR#_2_D

2 7 NRTS#_2_D

3 8 NCTS#_2_D

4 9 NRI#_2_D

5


ARC-15W33

2.10 ARC-BYT DB-E Jumpers & Connectors settings

2.10.1 CAN2.0 Switch (E_JCAN20)

CAN2.0A (11-bit)*

CAN2.0B (29-bit)

*Default

2.10.2 For user update FW (E_JBOOT0)

Default*

For user update FW

*Default



2.10.3 For user update FW (E_JIAP1)

*Default

2.10.4 For user update FW (E_CN1)

Default*

For user update FW

Signal

+3.3V

SWDIO

SWCLK

CAN_BUS_RESET# 4

GND 5

PIN

1

2

3


ARC-15W33

2.10.5 General purpose I/O connector (E_GPIO1)

DI5

DI4

DI3

DI2

DI1

DI0

Signal

GND

+3.3V

DO5

DO4

DO3

DO2

DO1

DO0

4

3

6

5

2

1

10

9

8

7

PIN

14

13

12

11

2.10.6 CAN Bus connector (E_CAN1)

Signal

CANH

CANL

GND

PIN

1

2

3


2.11 ARC-BYT DB-F Connectors settings

2.11.1 CAN Bus connector 1 (F_CAN1)


2.11.2 CAN Bus connector 2 (F_CAN2)

Signal

CAN_PWR

CAN_IND

GND

PIN PIN

1 2

3 4

5 6

CAN_WAKE 7 8

UART_RXD_1_F 9 10

UART_TXD_1_F 11 12

+5V 13 14

Signal

CAN_8

CAN_9

BAT_GND

CAN_11

CAN_12

CAN_13

CAN_14

Signal

BAT_PWR

CAN_8

CAN_9

BAT_GND

CAN_11

PIN PIN

1 6

2 7

3 8

4 9

5

Signal

CAN_12

CAN_13

CAN_14

NC


ARC-15W33

2.12 ARC-BYT DB-G Connectors settings

2.12.1 Serial Port 1 connector (G_COM1)

Signal

NDCD#_3_G

NRXD_3_G

NTXD_3_G

NDTR#_3_G

GND

PIN PIN Signal

1 6 NDSR#_3_G

2 7 NRTS#_3_G

3 8 NCTS#_3_G

4 9 NRI#_3_G

5


Signal

NDCD#_2_G

NRXD_2_G

NTXD_2_G

NDTR#_2_G

GND

PIN PIN Signal

1 6 NDSR#_2_G

2 7 NRTS#_2_G

3 8 NCTS#_2_G

4 9 NRI#_2_G

5




2.13 ARC-BYT DB-H Jumpers settings

2.13.1 USB Power selector (H_USB_PWR_SEL1)

Signal

NDCD#_1_G

NRXD_1_G

NTXD_1_G

NDTR#_1_G

GND

PIN PIN Signal

1 6 NDSR#_1_G

2 7 NRTS#_1_G

3 8 NCTS#_1_G

4 9 NRI#_1_G

5

+5VSB*

+5V

*Default


ARC-15W33

2.14 ARC-BYT DB-H Connectors settings

2.14.1 Serial Port 1 connector (H_COM1)

Signal

NDCD#_1_H

NRXD_1_H

NTXD_1_H

NDTR#_1_H

GND

PIN PIN Signal

1 6 NDSR#_1_H

2 7 NRTS#_1_H

3 8 NCTS#_1_H

4 9 NRI#_1_H

5

2.14.2 Serial Port 2 connector (H_COM2)

Signal

NDCD#_2_H

NRXD_2_H

NTXD_2_H

NDTR#_2_H

GND

PIN PIN Signal

1 6 NDSR#_2_H

2 7 NRTS#_2_H

3 8 NCTS#_2_H

4 9 NRI#_2_H

5



2.15 ARC-BYT DB-K Connectors settings

2.15.1 Serial Port 1 connector (I_COM1)

Signal

NDCD#_1_I

NRXD_1_I

NTXD_1_I

NDTR#_1_I

GND

PIN PIN Signal

1 6 NDSR#_1_I

2 7 NRTS#_1_I

3 8 NCTS#_1_I

4 9 NRI#_1_I

5

2.15.2 Serial Port 2 connector (I_COM2)

Signal

NDCD#_2_I

NRXD_2_I

NTXD_2_I

NDTR#_2_I

GND

PIN PIN Signal

1 6 NDSR#_2_I

2 7 NRTS#_2_I

3 8 NCTS#_2_I

4 9 NRI#_2_I

5


ARC-15W33

3.BIOS Setup



3.1 Introduction

The AMI setup program allows users to modify the basic system configuration. In this following chapter will describe how to access the BIOS setup program and the configuration options that may be changed.

3.2 Starting Setup

The AMI BIOS ™ is immediately activated when you first power on the computer. The BIOS reads the system information contained in the NVRAM and begins the process of checking out the system and configuring it. When it finishes, the BIOS will seek an operating system on one of the disks and then launch and turn control over to the operating system.

While the BIOS is in control, the Setup program can be activated in one of two ways:

By pressing <Del> or <F2> immediately after switching the system on, or

By pressing the <Del> or <F2> key when the following message appears briefly at the left-top of the screen during the POST (Power On Self Test).

Press <Del> or <F2> to enter SETUP

If the message disappears before you respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or pressing the "RESET" button on the system case. You may also restart by simultaneously pressing <Ctrl>, <Alt>, and <Delete> keys. If you do not press the keys at the correct time and the system does not boot, an error message will be displayed and you will again be asked to.

Press F1 to Continue, DEL to enter SETUP


ARC-15W33

3.3 Using Setup

In general, you use the arrow keys to highlight items, press <Enter> to select, use the

PageUp and PageDown keys to change entries, press <F1> for help and press <Esc> to quit. The following table provides more detail about how to navigate in the Setup program using the keyboard.

Button

↑

↓

←

→

Description

Move to previous item

Move to next item

Move to the item in the left hand

Esc key

+ key

- key

Move to the item in the right hand

Main Menu -- Quit and not save changes into NVRAM

Status Page Setup Menu and Option Page Setup Menu -- Exit current page and return to Main Menu

Increase the numeric value or make changes

Decrease the numeric value or make changes

F1 key General help, only for Status Page Setup Menu and Option Page Setup Menu

F2 key

F3 key

F4 key

Previous Values.

Optimized defaults

Save & Exit Setup



Navigating Through The Menu Bar

Use the left and right arrow keys to choose the menu you want to be in.

Note: Some of the navigation keys differ from one screen to another.



To Display a Sub Menu

Use the arrow keys to move the cursor to the sub menu you want. Then press

<Enter>. A “  ” pointer marks all sub menus.



3.4 Getting Help

Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window press <Esc> or the F1 key again.

3.5 In Case of Problems

If, after making and saving system changes with Setup, you discover that your computer no longer is able to boot, the AMI BIOS supports an override to the NVRAM settings which resets your system to its defaults.

The best advice is to only alter settings which you thoroughly understand. To this end, we strongly recommend that you avoid making any changes to the chipset defaults. These defaults have been carefully chosen by both BIOS Vendor and your systems manufacturer to provide the absolute maximum performance and reliability. Even a seemingly small change to the chipset setup has the potential for causing you to use the override.


ARC-15W33

3.6 BIOS setup

Once you enter the Aptio Setup Utility, the Main Menu will appear on the screen. The Main

Menu allows you to select from several setup functions and exit choices. Use the arrow keys to select among the items and press <Enter> to accept and enter the sub-menu.

3.6.1 Main Menu

This section allows you to record some basic hardware configurations in your computer and set the system clock.



3.6.1.1 System Language

This option allows choosing the system default language.

3.6.1.2 System Date

Use the system date option to set the system date. Manually enter the day, month and year.

3.6.1.3 System Time

Use the system time option to set the system time. Manually enter the hours, minutes and seconds.

Note: The BIOS setup screens shown in this chapter are for reference purposes only, and may not exactly match what you see on your screen.

Visit the Avalue website ( www.avalue.com.tw

) to download the latest product and BIOS information.

3.6.2 Advanced Menu

This section allows you to configure your CPU and other system devices for basic operation through the following sub-menus.


ARC-15W33

3.6.2.1 Trusted Computing

Item

Security Device Support

Physical Presence Spec Version

3.6.2.2 APCI Settings

Options

Disable,

Enable [Default]

1.2

1.3

[Default]

Description

Enables or Disables BIOS support for security device. O.S. will not show Security Device. TCG

EFI protocol and INT1A interface will not be available.

Select to Tell O.S. to support PPI Spec Version

1.2 or 1.3 Note some HCK tests might not support 1.3.


Item

Enable Hibernation

ACPI Sleep State

ErP Function

PWR-On After PWR-Fail

Watch Dog

USB Standby Power Setting

Wake Up by Ring

Disabled

Enabled [Default] ,


Options

Disabled

Enabled [Default] ,

Suspend Disabled,

S3 (Suspend to RAM) [Default]

Description

Enables or Disables System ability to

Hibernate (OS/S4 Sleep State). This option may be not effective with some

OS.

Select the highest ACPI sleep state the system will enter when the SUSPEND button is pressed.

Disabled [Default] ,

Enabled

Off [Default]

On

Last state


30 sec

40 sec

50 sec

1 min

2 min

10 min

30 min

Disabled

Enabled [Default] ,

ErP Function (Deep S5).

AC loss resume.

Select WatchDog.

Enabled/Disabled USB Standby Power during S3/S4/S5.

Wake Up by Ring from S3/S4/S5.


ARC-15W33

3.6.2.3 IT8528 Super IO Configuration

You can use this item to set up or change the IT8528 Super IO configuration for serial ports.

Please refer to 3.6.2.3.1~ 3.6.2.3.5 for more information.

Item

DB board

Options

DB-A/C/E/J

DB-B

DB-F 1COM

DB-D/H/K 2COM

DB-G 3COM

M/B mode test [Default] ,

Description

DB board A-K. DA-A/B/C/E/J w/o UART DB-G w/t

3UART DB-D/H/K w/t 2UART DB-F w/t 1UART.

Serial Port 1 Configuration Set Parameters of Serial Port 1 (COMA).

Serial Port 2 Configuration Set Parameters of Serial Port 2 (COMB).

Serial Port 3 Configuration Set Parameters of Serial Port 3 (COMC).

Serial Port 4 Configuration Set Parameters of Serial Port 4 (COMD).

Serial Port 5 Configuration Set Parameters of Serial Port 5 (COME).


3.6.2.3.1 Serial Port 1 Configuration


Item

Serial Port

UART 232 422 485

Option

Enabled [Default] ,

Disabled

UART 232 [Default]

UART 422

UART 485


Description

Enable or Disable Serial Port (COM).

Change the Serial Port


ARC-15W33

Item

Serial Port

Option

Enabled [Default] ,

Disabled


Description


Item

Serial Port

Option

Enabled [Default] ,

Disabled


Description




Item

Serial Port

Option

Enabled [Default] ,

Disabled


Description


Item

Serial Port

3.6.2.4 H/W Monitor

Option

Enabled [Default] ,

Disabled

Description



ARC-15W33

3.6.2.5 S5 RTC Wake Settings

Item

Wake system from S5

Options


Fixed Time

Dynamic Time

Description

Enable or disable System wake on alarm event. Select

Fixed Time, system will wake on the hr::min::sec specified. Select Dynamic Time, System will wake on the current time + Increase minute(s).

3.6.2.6 Serial Port Console Redirection



Item

Console Redirection

Options


Enabled

3.6.2.6.1 Legacy Console Redirection Settings

Description

Console Redirection Enable or Disable.

Item

Legacy Serial Redirection Port

Option

COM0 [Default] ,

Description

Select a COM port to display redirection of

Legacy OS and Legacy OPROM Messages.

3.6.2.7 CPU Configuration

Use the CPU configuration menu to view detailed CPU specification and configure the

CPU.


ARC-15W33

Item Options

Intel Virtualization Technology

Disabled,

Enabled [Default]

VT-d


Enabled

3.6.2.7.1 Socket 0 CPU Information

Description

When enabled, a VMM can utilize the additional hardware capabilities provided by

Vanderpool Technology.

Enable/Disable CPU VT-d.

3.6.2.7.2 CPU Power Management Configuration



Item

EIST

Turbo Mode

C-States

Options

Disabled,


Disabled,


Disabled,


Disabled,


Enable/Disable Intel SpeedStep.

Turbo Mode.

Description

Enable/Disable C States.

Enhanced C-states

Max Package C State

Max Core C State

C-State Auto Demotion

C-State Un-demotion

PC2 [Default]

PC1

C0

Fused value [Default]

Core C10

Core C9

Core C8

Core C7

Core C6

Core C1

Unlimited

Disabled,

C1 [Default]

Disabled,

C1 [Default]

3.6.2.8 Network Stack Configuration

Enable/Disable C1E. When enabled, CPU will switch to minimum speed when all cores enter

C-State.

Controls the Max Package C State that the processor will support.

This option controls the Max Core C State that cores will support.

Configure C-State Auto Demotion.

Configure C-State Un-demotion.


ARC-15W33

Item

Network Stack

3.6.2.9 CSM Configuration

Options

Enabled

Disabled [Default]

Description

Enable/Disable UEFI Network Stack.

Item

CSM Support

3.6.2.10 NVMe Configuration

Options

Enabled


Description

Enable/Disable CSM Support.



3.6.2.11 USB Configuration

The USB Configuration menu helps read USB information and configures USB settings.

Item

Legacy USB Support

XHCI Hand-off

USB Mass Storage Driver Support

USB transfer time-out

Device reset time-out

Device power-up delay

Mass Storage Devices

Options


Disabled

Auto


Disabled


Disabled

1 sec

5 sec

10 sec

20 sec [Default]

10 sec

20 sec [Default]

30 sec

40 sec

Auto [Default]

Manual

Auto [Default]

Floppy

Forced FDD

Hard Disk

CD-ROM

Description

Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.

This is a workaround for OSes without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver.

Enable/Disable USB Mass Storage Driver

Support.

The time-out value for Control, Bulk, and

Interrupt transfers.

USB mass storage device Start Unit command time-out.

Maximum time the device will take before it properly reports itself to the Host Controller.

‘Auto’ uses default value: for a Root port it is

100ms, for a Hub port the delay is taken form

Hub descriptor.

Mass storage device emulation type. ‘AUTO’ enumerates devices according to their media format. Optical drives are emulated as

‘CDROM’, drives with no media will be emulated according to a drive type.


ARC-15W33

3.6.2.12 Security Configuration

Item

TXE HMRFPO

TXE EOP Message

3.6.3 Chipset

Options

Enabled



Disabled

TXE HMRFPO.

Description

Send EOP Message Before Enter OS.


3.6.3.1 North Bridge


Item

Max TOLUD

Above 4GB MMIO BIOS assignment

Option

2 GB [Default]

2.25 GB

2.5 GB

2.75 GB

Description

Maximum Value of TOLUD.

Enabled


Enable/Disable above 4GB

MemoryMappedIO BIOS assignment. This is disabled automatically when Aperture

Size is set to 2048MB.


ARC-15W33

3.6.3.2 South Bridge

Item

Serial IRQ Mode

OS Selection

Option

Quiet

Continuous [Default]

Windows [Default]

Android

Intel Linux

Description

Configure Serial IRQ Mode.

Select the target OS.

3.6.3.3 Uncore Configuration



Item

Active LVDS (Ch7511)

Brightness Control Method

LVDS Back Light PWM

LVDS Back Light PWM

Frequency

USB Touch

Option


Enabled

BIOS [Default]

BR Button

VR

OS Driver

00%

25%

50%

75%

100% [Default]

200 [Default]

300

400

500

700

1k

2k

3k

5k

10k

20k


Enabled

Active Internal LVDS(eDP->Ch7511-to-LVDS).

LVDS Brightness Control Method. 1.BIOS

2.Brightness Button 3.Variable Resistor 4.OS

Driver.

Description

Select LVDS back light PWM duty.

Select LVDS back light PWM Frequency.

Enable or Disable USB Touch.


ARC-15W33

3.6.3.4 South Cluster Configuration

3.6.3.4.1 HD-Audio Configuration

Item

HD-Audio Support

ARC-APL VerbTable

Description Option

Disable [Default] ,

Enable

5.1ch

2ch unmute speaker [Default]

Enable/Disable HD-Audio Support.

ARC-APL VerbTable.


3.6.3.4.2 PCI Express Configuration


Item

Compliance Mode

Option

Disable [Default] ,

Enable

3.6.3.4.2.1 PCI Express Root Port 3

Description

Compliance Mode Enable/Disable.


ARC-15W33

Item

PCI Express Root Port 3

ASPM

L1 Substates

PCIe Speed

Option

Disable


Disable [Default]

L0s

L1

L0sL1

Auto


L1.1

L1.2

L1.1 & L1.2

Auto [Default]

Gen 1

Gen 2


Description

Control the PCI Express Root Port. Enable:

Enable PCIe root port Disable: PCIe root port.

PCI Express Active State Power

Management settings.

PCI Express L1 Substates settings.

Configure PCIe Speed.

Item


ASPM

Option

Disable



L0s

L1

L0sL1

Auto

Description







L1 Substates

PCIe Speed


L1.1

L1.2

L1.1 & L1.2

Auto [Default]

Gen 1

Gen 2




Item


ASPM

L1 Substates

PCIe Speed

Option

Disable



L0s

L1

L0sL1

Auto


L1.1

L1.2

L1.1 & L1.2

Auto [Default]

Gen 1

Gen 2

Description








ARC-15W33


Item


ASPM

L1 Substates

PCIe Speed


Option

Disable



L0s

L1

L0sL1

Auto


L1.1

L1.2

L1.1 & L1.2

Auto [Default]

Gen 1

Gen 2

Description







3.6.3.4.4 SATA Drives


Item

Chipset SATA

Aggressive LPM Support

Port 0/1

SATA Device Type

SATA Port 0/1 DevSlp

Option

Enable [Default] ,

Disable

Description

Enables or Disables the Chipset the SATA

Controller. The Chipset SATA controller supports the 2 black internal SATA ports (up to

3Gb/s supported per port).

Enable PCH to aggressively enter link power state.


Enabled

Disabled


Hard Disk Drive [Default]

Solid State Drive


Enabled

Enable or Disable SATA Port.

Identify the SATA port is connected to Solid

State Driver or Hard Disk Drive.

Enable/Disable SATA Port 0/1 DevSlp. Board rework for LP needed before enable.


ARC-15W33

3.6.3.4.3 USB Configuration

Item

XHCI Pre-Boot Driver

3.6.4 Security

Option

Enable,


Description

Enable/Disable XHCI Pre-Boot Driver support.


 Administrator Password

Set setup Administrator Password

 User Password

Set User Password

3.6.4.1 Secure Boot menu



ARC-15W33

Item

Attempt Secure Boot

Secure Boot Mode

Option

Disabled



Enabled

Description

Secure Boot activated when Platform Key(PK) is enrolled, System mode is User/Deployes, and CSM function is disabled.

Secure Boot Mode – Custom_Standard, Set UEFI

Secure Boot Mode to STANDARD mode or CUSTOM mode, this change is effect after save. And after reset, the mode will returen to STANDARD mode.

3.6.5 Boot

Item

Setup Prompt Timeout

Bootup NumLock State

Quiet Boot

Boot Option #1

Option

1~ 65535

Description

Number of seconds to wait for setup activation key. 65535(0xFFFF) means indefinite waiting.

Select the Keyboard NumLock state

On [Default]

Off


Enabled

Set the system boot order.

Enables or disables Quiet Boot option


3.6.6 Save and exit


3.6.6.1 Save Changes and Reset

Reset the system after saving the changes.

3.6.6.2 Discard Changes and Reset

Any changes made to BIOS settings during this session of the BIOS setup program are discarded. The setup program then exits and reboots the controller.


ARC-15W33

3.6.6.3 Restore Defaults

This option restores all BIOS settings to the factory default. This option is useful if the controller exhibits unpredictable behavior due to an incorrect or inappropriate BIOS setting.

3.6.6.4 Launch EFI Shell from filesystem device

Attempts to Launch EFI Shell application (Shellx64.efi) from one of the available filesystem devices.


Avalue ARC-15W33 15.6” WXGA LCD Quick Reference Guide

ARC-15W33

15.6" Intel® Pentium®/Celeron®/Atom™ SoC Processor

Apollo Lake Fanless Rugged Touch Panel PC with IET

Expansion

Quick Reference Guide

Copyright Notice

FCC Statement

A Message to the Customer

Avalue Customer Services

Technical Support

Content

1. Getting Started

1.1 Safety Precautions

1.2 Packing List

1.3 System Specifications

1.4 System Overview

Connectors

1.5 System Dimensions

2. Hardware

Configuration

2.1 ARC-15W33 connector mapping

2.2 Installing Hard Disk & Memory

2.3 Installing ARC-BYT DB

2.4 ARC-APL Overviews

2.5 ARC-APL Jumper and Connector list

2.6 ARC-APL Jumpers & Connectors settings

2.7 ARC-BYT DB-A/B/C/D/E/F/G/H/K Overviews

2.8 ARC-BYT DB-A/B/C/D/E/F/G/H/K Connector list

2.9 ARC-BYT DB-D Connectors settings

2.10 ARC-BYT DB-E Jumpers & Connectors settings

2.11 ARC-BYT DB-F Connectors settings

2.12 ARC-BYT DB-G Connectors settings

2.13 ARC-BYT DB-H Jumpers settings

2.14 ARC-BYT DB-H Connectors settings

2.15 ARC-BYT DB-K Connectors settings

3.BIOS Setup

3.1 Introduction

3.2 Starting Setup

3.3 Using Setup

3.4 Getting Help

3.5 In Case of Problems

3.6 BIOS setup

Related manuals

Avalue Technology

OFT-15W33-3455-A2R

Grantech

SYM76999VGGA

Avalue

OFT-15W33

Avalue

OFP-15W33

Avalue

RITY152

Avalue Technology

EBM-APL

Avalue

ARC-1232-B

AXIOMTEK

tBOX110

Avalue Technology

ARC-1232

Avalue

ECM-APL

Avalue

ARC-10W33

Table of contents