- No category
advertisement
SSP-371-X-ISSUE4.0
SERVICE MANUAL
FOR
MODEL SSP-371-X
STAINLESS STEEL PANEL ELEVATOR
TELEPHONE
FOR MANUAL RING-DOWN OPERATION
Serving the Telephone Industry Since 1930
519 W South Park Street
Okeechobee, FL 34972
863-357-0798
863-357-0006
ISSUE 4.0
IMPORTANT INFORMATION
FOR
CUSTOMER
Please fill in before you continue.
The following information is necessary when calling CEECO for assistance.
MODEL NUMBER MODEL SSP-371-X STAINLESS STEEL PANEL
ELEVATOR PHONE
SERIAL NUMBER
DATE MANUFACTURED
LOCATION INSTALLED
For us to better serve you, please have this information available when calling for technical support.
CEECO
Communication Equipment & Engineering Company
519 W South Park Street
Okeechobee, FL 34972
863-357-0798- telephone
863-357-0006- facsimile [email protected]
www.ceeco.net
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
2
ISSUE 4.0
TABLE OF CONTENTS
SECTION PAGE
1.0 INTRODUCTION................................................................................................... 4
3.0 OPERATION .......................................................................................................... 4
4.0 RECOMMENDED TOOLS AND TEST EQUIPMENT .................................... 4
5.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS ..................... 5
6.0 TESTING................................................................................................................. 6
7.0 TROUBLESHOOTING ......................................................................................... 6
8.0 SPECIFICATIONS................................................................................................. 7
10.0 FCC NOTICE.......................................................................................................... 9
11.0 REPAIR AND RETURN INFORMATION....................................................... 10
12.0 WARRANTY POLICY ........................................................................................ 11
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
3
ISSUE 4.0
1.0 INTRODUCTION
The practices in this manual provide installation and maintenance information for the Model SSP-371-X Elevator Telephone.
The information in this manual is subject to change without notification.
For information not included in this manual, please call or write:
CEECO
Customer Service
519 W South Park Street
Okeechobee, FL 34972
863-357-0798- telephone
863-357-0006- facsimile [email protected]
www.ceeco.net
2.0 GENERAL DESCRIPTION
The CEECO Model SSP-371-X Elevator Telephone is a Special Service
Telephone designed for elevator installations, where a telephone must be both sturdy and vandal resistant. The telephone is designed to accept incoming calls only. The user cannot initiate a call. Any other type of operation would require the use of external dialing equipment.
3.0 OPERATION
An audible ringer indicates an incoming call. When the phone rings, lift the handset. Normal telephone operation will follow. When the call is completed, return the handset to the cradle.
4.0 RECOMMENDED TOOLS AND TEST EQUIPMENT
Volt/Ohm Meter
1/4
∀ Nut Driver
Flat Blade Screw Driver
Security Tool (sold separately)- CEECO P/N 301-037
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
4
ISSUE 4.0
5.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS
5.1 The SSP-371-X is designed to be mounted inside any apparatus box with dimensions of 6 7/8
∀W x 9 3/4∀H x 3∀D or greater. CEECO part number 371-011 is an apparatus box, which is well suited for this purpose.
Four mounting holes are required inside the box. If the holes are not tapped, then self-tapping screws should be used when mounting the panel.
It is best to use the security screws, which do require tapped mounting holes.
5.2
Mount the two mounting support brackets provided to the apparatus box being used. Route the inside station wire and terminate to an RJ11C modular jack or terminal block.
5.3
The use of a gas tube station protector is recommended. The station ground should not exceed 50 ohms.
5.4
Plug the modular line cord from the telephone assembly into the RJ11C modular jack or terminal block. Dress the line cable away from the mounting holes. Install the telephone assembly by placing it into its mounting box and securing it with the four security screws.
*****WARNING*****
A. Never install telephone lines during a lightning storm.
B. Never install telephone jacks in wet locations, unless the jack is
Specifically designed for wet locations.
C. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
D.
Use caution when installing or modifying telephone lines.
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
5
ISSUE 4.0
6.0 TESTING
6.1 Connect the phone to a working phone line or a DTMF test set.
6.2
From another phone or the DTMF test set, place a call to the SSP-371-X telephone.
6.3
Verify that the ringer is working.
6.4
Lift the handset and check that normal phone conversation is allowed.
7.0 TROUBLESHOOTING
Always visually check the phone for loose or shorted wires, damaged terminals or damaged parts,
PROBLEM: No dial tone. POSSIBLE CAUSE: Line cord
RJ11C Connector
Network
Handset
PROBLEM: Dial tone distorted. POSSIBLE
Handset
Network
PROBLEM: Ringer doesn’t work. POSSIBLE CAUSE: Ringer
Network
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
6
8.0 SPECIFICATIONS
INPUT POWER:
LOOP CURRENT:
C.O. Line Powered
23 mA min. to 80 mA max.
SIGNALING:
COMPATIBILITY:
DTMF, 70ms tone, 50ms spacing
Humidity
TELEPHONE PANEL: Brushed 16 gauge stainless steel
(handset on hook)
Vertical surface or enclosure mount MOUNTING:
WEIGHT:
RINGER EQUIVALENCY:
FCC REGISTRATION NO.:
UL LISTED NO.:
0.8A
BW-88T7-13717-TE-T
60F5
ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
7
ISSUE 4.0
1 371-014 Handset with coiled cord & magnetic plate
1 928-001 Strain
1 401-009 Ringer
1 301-009 Network
1 945-001 Magnetic reed switch assembly
1 371-003 Stainless
2 371-009 Mounting
4 406-019 10-32 x 1/2" Security Screws
OPTIONAL
730-103 Model 730-LNB MBTD
371-011 Mounting box
371-012 Frame assembly for mounting box
406-019 10-32 x ½” Security screw (4 req’d)
301-037 Security tool
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
8
ISSUE 4.0
10.1 FCC REGISTRATION AND REPAIR INFORMATION
Your new telephone has been registered with the Federal Communication
Commission (FCC) in accordance with Part 68 of its rules. The FCC requires that you be advised of certain requirements involving the use of this telephone.
10.2 CONNECTION AND USE WITH THE NATIONWIDE TELEPHONE
NETWORK
The FCC requires that you connect this telephone to the Nationwide
Telephone Network through a registered jack provided by the Telephone
Company in your area. This jack is a modular outlet, which you can order from your local telephone company.
10.3 NOTIFICATION TO THE TELEPHONE COMPANY
Before connecting this telephone, the FCC requires that you notify your local telephone company business office. The number is in the front of your phone book. them:
The "line" to which you will connect the telephone (that is, your phone number), the telephone's FCC registration number and ringer equivalence number. These numbers are listed in section 7.0
The FCC further requires that you notify your local telephone company when permanently disconnecting this telephone.
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
9
ISSUE 4.0
11.0 REPAIR AND RETURN INFORMATION
11.1 WARRANTY REPAIR
Any device returned requiring warranty service, repair or credit must be accompanied with a "Return Material Authorization" (RMA) FORM. It must include: return shipping instructions, original purchase order number and special marking instruction. A description of the trouble observed must be attached to the defective unit. This information must be inside the shipping container.
11.2 DIRECT ALL INQUIRES TO:
CEECO
Repair Department
863-357-0798- telephone
863-357-0006- facsimile [email protected]
www.ceeco.net
11.3 NON-WARRANTY REPAIR
CEECO will repair equipment out of warranty for a set charge plus parts.
The customer must pay the shipping costs for both directions.
11.4 RETURN FOR CREDIT
Material may be returned for credit only with prior approval. Material authorized for return is subject to a 20% restocking charge based on the manufacturer's list price. Return Material Authorization must be requested no later than 30 days after original shipment.
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
10
ISSUE 4.0
12.1 GENERAL
CEECO products are guaranteed to be free of defects in material and workmanship for a period of 365 days from the date of original purchase.
CEECO’s obligation under this warranty is limited to repair or replacement of any part found to be defective by CEECO. Under no circumstances shall CEECO be liable for loss, damage, cost of repair, or consequential damages of any kind which have been caused by neglect, abuse, acts of GOD, or improper operation of equipment.
CEECO will repair or replace any unit during this period if found to be defective for reasons other than abuse, neglect, acts of GOD, or improper operation. It is the buyer’s responsibility to return the defective unit to the factory. CEECO will then repair or replace any defective parts and return the unit to the buyer free of charge.
PRINTED CIRCUIT BOARDS
Printed circuit boards should not be field repaired. If a unit is found to be faulty, replace it with another unit and return the faulty unit to CEECO for repair. Modifications by anyone other than CEECO will void the warranty.
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
11
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project