CADDX NX4 Manual

TM
NETWORX NX-4
User manual
WWW.DIYALARMFORUM.COM
POWER Light is “on” when AC
power is present; flashes to
indicate a low battery condition.
ZONE LIGHTS are “on” steady to
indicate bypass; slow flash for
zone fault; rapid flash for service
condition.
PULL OUT ZONE ID TAB
FIRE Light is “on” to indicate fire
alarm; flashes to indicate a
trouble condition with your fire
system.
INSTANT Light is “on” when
there is no entry/exit delay.
ARMED Light is “on” when
armed; “off” when disarmed;
flashes to indicate a previous
alarm.
WWW.DIYALARMFORUM.COM
NOTE: Some of the features described above may or may not be available for your system.
Check with your installation company to find out how your system is programmed.
NUMERIC CODE
ENTRY KEYS
Includes models
NX-108E, NX-116E, NX-124E
NX-4 SYSTEM
KEYPAD
EMERGENCY ACTIVIATION KEYS
SERVICE Light is “on” to indicate a
trouble condition with your system.
5 FUNCTION KEYS perform
various functions.
READY Light is “on” when the
system is ready to arm; flashes
if ready to “force arm”.
SECURITY SYSTEM NOTES
Installing/Service Company _________________________________
For Service Call __________________________________________
Central Station ___________________________________________
Duress Code ____________________
FUNCTION CODES
Function Code
Controls Function
EMERGENCY ACTIVATION KEYS (check if enabled)
Fire
Auxiliary Emergency
Police
PROGRAMMED FUNCTIONS
Abort Delay (s)
Cancel Alarm
Group Bypass (s)
Auto Bypass (s)
Chime
Quick Arm (s)
Auto Instant
Communicator Test
Re Exit
Battery Test
Forced Arming (s)
Siren Test
(s) These features should not be enabled on UL listed systems.
ENTRY / EXIT DELAY TIMES
Exit Delay Time __________
Secondary Exit Delay Time ________
Entry Delay Time _________
Secondary Entry Delay Time _______
ZONE DESCRIPTIONS
01 _______________________
02 _______________________
03 _______________________
04 ________________________
05 ________________________
06 ________________________
07 ________________________
08 ________________________
Installer: Mark wireless zones with an “u” as required by UL.
1
WWW.DIYALARMFORUM.COM
THIS MANUAL IS FURNISHED TO HELP YOU UNDERSTAND YOUR SECURITY
SYSTEM AND BECOME PROFICIENT IN ITS OPERATION. ALL USERS OF
YOUR SECURITY SYSTEM SHOULD READ AND FOLLOW THE INSTRUCTIONS
AND PRECAUTIONS IN THIS BOOKLET. FAILURE TO DO SO COULD RESULT
IN THE SECURITY SYSTEM NOT WORKING PROPERLY. THIS BOOKLET
SHOULD BE KEPT IN AN ACCESSIBLE LOCATION FOR THE LIFE OF THE
SECURITY SYSTEM. IF YOU DO NOT UNDERSTAND ANY PART OF THIS
MANUAL YOU SHOULD NOTIFY YOUR INSTALLING COMPANY.
The SECURITY CONTROL can be turned on (ARMED) and off (DISARMED) by
entering a 4 or 6 digit code into the Keypad Control, which is similar to a telephone
keypad. If your Security Control has been so programmed, you may be able to turn on
(ARM) your System by simply pressing the [STAY] or [EXIT] key. The system must
always be disarmed using a 4 or 6 digit code. The LED keypad includes up to 35 lights
and a built-in electronic sounder. These provide specific information relating to the
status of the security system which is described in the booklet. Understanding what
the lights and sounds mean will help you to easily operate your system.
READ THE ENTIRE MANUAL AND, IF POSSIBLE, PRACTICE ON THE KEYPAD
CONTROL WHILE YOUR PROFESSIONAL INSTALLER IS ON SITE.
KEEP IN MIND, THE LEVEL OF SECURITY YOU WILL OBTAIN WITH THIS
SYSTEM RELATES SPECIFICALLY WITH TWO MAJOR FACTORS:
1.
2.
The quantity, quality, and placement of security devices attached to this
system.
The knowledge you have of the security system and how that knowledge is
utilized in a weekly test of the complete system.
YOU SHOULD BE AWARE OF THE FOLLOWING FACTS WHEN PREPARING A
SAFETY/SECURITY PLAN FOR YOUR HOME/BUSINESS.
Your security system is an electronic device and is subject to failure or
malfunction. Do not rely on it as your single source of security.
Your system should be tested weekly.
Your system will not work without power.
Warning devices will need to be loud enough, wired correctly, and properly
placed to provide notification of an alarm event.
Smoke and heat detectors may not detect heat and smoke in all situations.
Use qualified security professionals to install and maintain your security system.
It may be possible to arm the security system without the backup battery
connected. Your periodic test should be done with A.C. Power removed to verify
the battery is connected and adequately charged.
Care should be taken to plug in and restrain the A.C. Transformer after testing.
PLEASE READ THE FOLLOWING INFORMATION AND INSTRUCTIONS
CAREFULLY BEFORE OPERATING YOUR SECURITY CONTROL SYSTEM. IF
YOU DO NOT UNDERSTAND ANY PORTION OF THIS MANUAL, OR IF YOU
HAVE ANY QUESTIONS ABOUT YOUR SYSTEM, CONTACT THE INSTALLING
COMPANY LISTED ON PAGE 1 OF THIS BOOKLET.
2
WWW.DIYALARMFORUM.COM
TABLE OF CONTENTS
GLOSSARY OF TERMS ....................................................................4
UNDERSTANDING THE LIGHTS.....................................................5
Armed Light ......................................................................................5
Bypass Light.....................................................................................5
Cancel Light .....................................................................................5
Chime Light ......................................................................................5
Exit Light...........................................................................................5
Fire Light ..........................................................................................5
Instant Light......................................................................................5
Power Light ......................................................................................5
Ready Light ......................................................................................5
Stay Light .........................................................................................6
Zone Light ........................................................................................6
EMERGENCY ACTIVATION KEYS .................................................6
KEYPAD FUNCTIONS .......................................................................7
Arming Your System In The “Away” Mode .......................................7
Arming Your System In The “Stay” Mode.........................................7
Using The Quick Arm ......................................................................8
Disarming Your System....................................................................8
Cancel / Abort Feature ....................................................................9
Bypassing Zones..............................................................................9
Group Bypass...................................................................................9
Unbypassing.....................................................................................9
Turning The Door Chime On And Off...............................................9
CHANGING USER CODES .............................................................10
ASSIGNING USER CODE AUTHORITY LEVELS ......................10
OTHER KEYPAD FUNCTIONS ......................................................11
Setting The Keypad Tone...............................................................11
View Alarm Memory .......................................................................11
Test Function .................................................................................12
Walk Test .......................................................................................12
Reset Function ...............................................................................12
Setting The System Date ...............................................................12
Setting The System Clock ..............................................................13
KEYPAD CONTROL TONES (BEEPS) .........................................14
SERVICE MENU ................................................................................15
EMERGENCY EVACUATION PLANS ...........................................16
3
WWW.DIYALARMFORUM.COM
GLOSSARY OF TERMS
Abort Delay: An option that allows a delay in reporting to the central station.
There is a communicator delay of 30 seconds. It can be removed, or increased
up to 45 seconds at the option of the end user by consulting with the installer.
Authority Level: The level of access an individual has when using an alarm
panel.
Central Station: Location where alarm data is sent during an alarm report.
Chime Feature: An option that allows the keypad to sound a ding-dong
whenever an entry/exit door is opened.
Codes: Can be either User Codes (relating to a person) or Function Codes (a
toggle switch to turn specific functions on/off). NOTE: A system may have either
8 four (4) digit codes or 8 six (6) digit codes, but not a mixture of the two.
Duress Code: An option that allows a special code to be sent to the central
station that indicates the alarm system is being operated under duress. Any
arming or disarming operation performed using the Duress PIN (in lieu of the
User PIN) will operate normally, without additional audible or visual indicators.
Forced Arming: An option that allows the system to be turned on (ARMED) with
one or more zones open. A system that is ready to be “force armed” will flash the
ready light. (Note: Those zones that are not ready will not create an alarm.)
Function Code: A Function Code is either a four (4) or six (6) digit code that has
been programmed by the installer to operate a device.
Group Bypass: An option that allows the user to bypass multiple zones with a
single operation.
Instant/Delay: An option that allows an instant alarm condition for Entry/Exit
doors, or grants a delay to allow someone to enter/exit the building without an
alarm, or before entering a user code to disarm.
Master Code: A master arm/disarm code that can program other user codes.
Perimeter: The outer edge of the protected area.
Quick Arm: An option that allows you to turn on (ARM) the security system by
pressing either the [STAY] or [EXIT] key on the keypad control (for ARMING
only) as programmed by the installing company.
User Code: A four (4) or six (6) digit entry used to arm or disarm the system.
4
WWW.DIYALARMFORUM.COM
UNDERSTANDING THE LIGHTS
Armed Light
The armed light is “on” when the system is armed. The armed light is “off”
when it is disarmed. The armed light will flash when there has been an alarm
during the previous arm cycle.
Bypass Light
The bypass light is “on” when any zone is bypassed. The zone(s) that is
bypassed will also be illuminated. If the bypass light is “off”, no zones are
bypassed.
Cancel Light
The cancel light will flash during an abort delay time. If a code is entered
followed by the [CANCEL] key while this light is flashing, all abortable reports
will stop the communication process. Note: The abort feature must be
enabled. Entering a code followed by the [CANCEL] key during or after an
alarm report to the central station will cause the cancel light to come on. It will
stay on until the central station has received the cancel report. Note: The
cancel feature must be enabled. No additional keypad tones will be emitted.
Chime Light
The chime light is “on” when the chime feature is “on”; “off” otherwise.
Exit Light
The exit light is “on” during the exit delay. During the last 10 seconds of the exit
delay, the exit light will flash rapidly and the keypads will beep rapidly as a
warning to the user that the exit time is about to expire. (The user may want to
disarm the system if the exit light is flashing in order to prevent an alarm. The
user may then re-arm the system and exit before the delay expires.)
Fire Light
A steady fire light means a fire zone has been faulted. A rapidly flashing fire
light means that a fire zone is in a trouble condition.
Instant Light
The instant light is “on” when there is no delay on your entry/exit door(s). Any
time the instant light is “on” and the exit delay has expired, the opening
of an entry/exit door will produce an immediate alarm. The instant light can
be toggled on or off by pressing the [Stay] key while the system is armed.
When the instant light is “off”, the entry/exit door(s) is delayed.
Power Light
The power light is on if the primary power is on. The power light will flash if the
system has a low battery condition.
Ready Light
The ready light is “on” when the system is ready to arm and “flashes” if ready to
force arm. The ready light is off when the system is not ready to arm because
of a zone(s) being faulted.
5
WWW.DIYALARMFORUM.COM
Stay Light
The stay light is “on” when the all interior (motion detector) zones are
bypassed.
Zone Light
The zone lights are “off” when everything is normal. A zone light will be “on” if
the zone has been bypassed. If a zone light is “flashing”, that zone is in alarm
or has been faulted. If a zone light is “flashing” rapidly, it means that the zone is
in a trouble condition. Trouble conditions are:
Tamper
Hardware
Low Battery
Loss of Supervision
(A combination of Alarm/Fault and Tamper/Trouble will produce a rapid
“flashing” light for a short period of time, followed by a slow “flashing” light.)
EMERGENCY ACTIVATION KEYS
NOTES: You must press and hold these keys for 2 seconds to activate
these functions. Your system may not be programmed for these activation
keys (see page 1). You should press these keys only in an emergency situation
that requires response by emergency personnel. If your system is programmed
for these functions, the following reports can be sent.
Fire Key – This key can activate the fire alarm when pressed for two seconds. If
your system is connected to a monitoring center, an emergency report could be
sent to that center. The keypads sound a continuous beeping.
Auxiliary Emergency Key – This key can activate the auxiliary alarm when
pressed for two seconds. If your system is connected to a monitoring center, an
emergency report could be sent to that center. The keypads sound a continuous
beeping.
Police (Panic/Hold-Up) Key - This key can sound a local audible alarm when
pressed for two seconds. If your system is connected to a monitoring center, an
emergency report could be transmitted to that center. NOTE: Some Panic/HoldUp alarms are programmed to be silent at the protected site while reporting an
alarm to the monitoring center. Check with your installing company to determine
how your security system will respond to the Panic/Hold-Up activation. If
programmed for Silent Hold-up, the keypads will not sound. Otherwise, the
keypads will sound a continuous beeping.
6
WWW.DIYALARMFORUM.COM
KEYPAD FUNCTIONS
ARMING YOUR SYSTEM IN THE “AWAY” MODE
AWAY is used when the user is away from the premise and wants the interior
protected. Listed below are the steps to arm in the AWAY Mode:
Step 1 Close all protected doors and windows.
• Ready light will be on or flashing when all protected zones and
sensors are secure. NOTE: If any zones are bypassed, a sensor
in that zone can be violated without affecting the ready light.
• The security system will not arm if the ready light is not on or
flashing.
• If the power light is off, you have no AC power. Restore power if
possible. If not, contact your installing company listed on page 1 of
this booklet for service.
Step 2
• Enter your user code to arm the system.
• The armed and exit lights will illuminate.
• You may now leave the building.
Note: The keypads beep slowly during an exit delay. During the last 10 seconds
of the exit delay, the keypads beep rapidly and the exit light will flash rapidly
as a warning to the user that the exit time is about to expire. At the end of the
exit delay, the keypads beep one longer tone (1 second). The user may wish
to disarm and re-arm the system if more time is needed.
ARMING YOUR SYSTEM IN THE “STAY” MODE
STAY is used when the user is inside the premise and wants protection around
the perimeter. Listed below are the steps to arm in the STAY Mode:
Step 1 Close all protected doors and windows.
• Ready light must be on or flashing when all protected zones and
sensors are secure. NOTE: If any zones are bypassed, a sensor
in that zone can be violated without affecting the ready light.
• The security system will not arm if the ready light is not on or
flashing.
• If the power light is off, you have no AC power. Restore power if
possible. If not, contact your installing company listed on page 1 of
this booklet for service.
Step 2
• Enter your 4 or 6 digit user code.
• If “Auto Bypass” is enabled, all interior zones will be bypassed if you
do not leave through a designated entry/exit door. If Auto Bypass is
enabled, omit Step 3.
• When “Auto Instant” is enabled, if you do not leave through a
designated entry/exit door the instant light will illuminate indicating
that the entry/exit doors no longer have an entry delay. If “Auto
Instant” is enabled, omit Step 4.
7
WWW.DIYALARMFORUM.COM
Step 3
• Press the [STAY] key.
• The stay light will illuminate indicating that all interior zones are
bypassed. (All interior devices will bypass automatically, giving the
user freedom of movement within the interior area.)
• The bypass light will illuminate if any zone(s) are bypassed. If any
zone(s) have been bypassed previously by the user, the light(s)
corresponding to the bypassed zone(s) will illuminate, alerting the
user that a zone(s) may be unprotected and can be faulted without
an alarm.
Step 4
• To toggle from a “delayed entry” mode to an “Instant” mode, press
the [STAY] key again.
• The instant light will illuminate indicating that the entry/exit doors
have no entry delay.
USING THE QUICK ARM (Optional, see page 1)
The Quick Arm feature may be used if it is enabled. Quick Arm will allow the user
to arm the security system in the AWAY mode by pressing the [EXIT] key, or arm
in the STAY mode by pressing the [STAY] key. The keypads beep during the exit
delay; beeps rapidly for the last 10 seconds of the exit delay; and beeps 1 second
at the end of the exit delay. This feature is used for ARMING ONLY, and will not
disarm the security system. This is ideal for a maid or baby sitter code, etc.
CHANGING MODES WHILE YOUR SYSTEM IS ARMED
Pressing the [STAY] key will turn on/off (toggle) a delay on entry/exit doors
and turn on/off (toggle) the instant light.
(Optional) Press the [BYPASS] key at this time to turn on/off (toggle) all
designated interior zones.
(Optional) When armed, pressing the [EXIT] key will start the exit delay,
enabling you to leave the building.
IMPORTANT
The instant light needs to be off at this time if you plan on re-entering the
building; otherwise you will create an alarm. You may restore an entry
delay by pressing the [STAY] key again.
DISARMING YOUR SYSTEM
When you enter the protected area through one of the designated Entry/Exit
doors, the keypad control will sound a continuous tone for the duration of the
entry delay time, or until you enter a valid code. The red armed light will go off
and the tone will stop. The security system is now DISARMED. If a valid code is
not entered before the end of the entry delay, an alarm will occur. (NOTE: If the
red armed light is flashing during the entry delay, the alarm system has
been activated in your absence. Leave the building immediately and call
your alarm company and/or the police from a safe location.)
8
WWW.DIYALARMFORUM.COM
CANCEL / ABORT FEATURE (Optional, see page 1)
The cancel light will flash during an abort delay time. If a code is entered
followed by the [CANCEL] key while this light is flashing, all abortable reports will
stop the communication process. Entering a code followed by the [CANCEL] key
during or after an alarm report to the central station will cause the cancel light to
come on. It will stay on until the central station has received the cancel report. No
additional keypad tones will be emitted.
BYPASSING ZONES
If you wish to bypass one or more zones, this must be done while the system is in
the disarmed state. The following steps are used for bypassing zones:
Step 1
Press the [BYPASS] key.
Step 2
Enter user code, if required (optional). The bypass light flashes.
Step 3
Enter the 1-digit number for the zone you wish to bypass. (Example:
Press the [1] key for zone 1, press [4] for zone 4.)
Step 4
Press the [BYPASS] key again.
Step 5
The corresponding zone light will illuminate indicating the zone has
been bypassed. Repeat steps 3 and 4 for any other zone(s) that
need to be bypassed.
Step 6
Press the [BYPASS] key again -or- press the [#] key to exit the
Bypass Mode. The bypass light will stop flashing upon exiting the
Bypass Mode.
GROUP BYPASS
By pressing the [BYPASS] key, followed by the [0] key, then the [BYPASS] key
again, all zones that are designated as group bypass zones will be bypassed.
Press the [BYPASS] key again to exit group bypassing.
UNBYPASSING
To unbypass zones, perform the bypassing procedure on the zone(s). The
corresponding light for that zone will go off when unbypassed. NOTE: All zones
will automatically be unbypassed each time the system is disarmed.
TURNING THE DOOR CHIME ON AND OFF
The door chime is turned on or off by pressing the [CHIME] key while the system
is in the disarmed state. If the chime is on the chime light will be illuminated. If the
chime is off, the chime light will be off. Each press of the [CHIME] key will toggle
the chime feature on/off and produce a momentary ding-dong sound.
9
WWW.DIYALARMFORUM.COM
CHANGING USER CODES
Step 1
Your system must be in the Disarmed state to change user codes.
Step 2
Press [r]-[5].
Step 3
Enter a “Master Arm/Disarm Code”.
Step 4
The ready light will flash.
Step 5
Enter the 2-digit “user number” (always enter 2 digits such as [0] - [3]
for user 3).
Step 6
Enter the new four (4) or six (6) digit “user code”.
NOTE: To delete a user code, enter [r]-[r]-[r]-[r] for a 4-digit code,
or [r]-[r]-[r]-[r]-[r]-[r] for a 6-digit code.
Step 7
The ready light will flash indicating you are back at Step 4 above. If
the code is rejected, the sounder will beep 3 times.
Step 8
If another “user code” needs to be programmed, return to Step 5.
Step 9
Press the [#] key while the ready light is flashing to exit the User
Code Programming Mode.
ASSIGNING USER CODE AUTHORITY LEVELS
Assign authority levels to users by following the steps below. Assign user codes
before assigning authority levels.
Step 1
Press [r]-[6].
Step 2
Enter a “Master Arm/Disarm Code”.
Step 3
The ready light will flash.
Step 4
Enter the 2 digit “user number” to be assigned authority (always 2
digits such as 03 for user 3). The ready light is constant and the
instant light will flash.
Step 5
Lights illuminated indicate the authority levels assigned to this code.
An explanation of the lights is listed below. You may toggle (turn
on/off) the authority level by pressing the number for that authority
level.
10
WWW.DIYALARMFORUM.COM
LIGHT
AUTHORITY LEVELS IF LIGHT 8 IS OFF
1
Reserved
2
Arm Only
3
Arm Only After Closing Time
4
Master Arm/Disarm (can program other codes)
5
Arm/Disarm
6
Bypass Zones
7
Open / Close Reporting
If this light is on, this code is programmed as a
function code. Do not change! Press [#] - [#] to
exit.
8
(Note: Do not change if on.)
Step 6
Press [r] [r].
This returns you to Step 3 above. At this point you may enter
another user number to assign authority level. Repeat Steps 4 - 6
until you have assigned authority levels to all user numbers.
Step 7
Press the [#] key to exit the Assigning Authority Level Program.
OTHER KEYPAD FUNCTIONS
SETTING THE KEYPAD TONE
Step 1
Press [r]-[0]. Keypad is now in the “Adjust Tone” mode.
Step 2
Pressing the [1] key will make the keypad sounder go to higher
tones, pressing the [2] key will make the keypad sounder go to lower
tones.
Step 3
When the desired tone is reached, press the [#] key to set this tone
and exit from the “Adjust Tone” mode.
VIEW ALARM MEMORY
Step 1
Press [r]-[3].
The zone(s) that created the last alarm will be
displayed on the keypad.
Step 2
The ALARM MEMORY feature will flash those zones that created
alarms and will light steady those zones that were bypassed during
the last alarm.
11
WWW.DIYALARMFORUM.COM
TEST FUNCTION – Optional
If programmed, this function will perform a battery test, communicator test, and/or
a siren test. No alarms will be sent and no reports will be sent unless a
communicator test is performed, at which time a test signal will be sent.
Step 1
Press [r]-[4]. The test will be performed as programmed.
Step 2
If the siren test is performed, enter a user code to silence the siren.
WALK TEST
If enabled, it will permit a temporary walk-through test where all zones become
silent and do not report alarms to the central station.
Step 1
Press [r]-[Chime]-[user code]. During this test the chime light will
flash on the LED keypad.
Step 2
Each time a zone is faulted, the zone light on the LED keypad will
illuminate and the chime will sound. The number of the faulted
zone(s) will be displayed on the LCD keypad. It will also be entered
into alarm memory and the internal log.
Step 3
The keypad will begin to beep after 15 minutes in this mode. This
beeping indicates that the “Walk-Test” mode will be automatically
exited in 5 minutes.
Step 4
To exit at any time during this mode, enter a user code. Otherwise
the AWalk-Test Mode@ will automatically exit after 20 minutes.
RESET FUNCTION
This function is used to reset Smoke Detectors, Zone Troubles, and Zone
Tampers.
Step 1
Disarm the system if not disarmed.
Step 2
Press [r]-[7]. Resets have now been performed.
Step 3
If the keypad begins beeping, the reset did not execute properly.
Enter your code to silence the keypad. Wait a few minutes and
repeat step 2 to attempt another reset. If the keypad still beeps after
repeated attempts, please contact your installer.
SETTING THE SYSTEM DATE
Step 1
Press the [r]-[9]-[6].
Step 2
Enter the “Master Code”.
12
WWW.DIYALARMFORUM.COM
Step 3
Enter the “Day of Week “
1 = Sunday
3 = Tuesday
2 = Monday
4 = Wednesday
5 = Thursday
6 = Friday
7 = Saturday
Step 4
Enter the “Month Code”. Must always be two (2) digits.
01 = January
05 = May
09 = September
02 = February
06 = June
10 = October
03 = March
07 = July
11 = November
04 = April
08 = August
12 = December
Step 5
Enter the “Day Code”. Must always be two (2) digits.
Example: The 5th would be entered as [0]–[5].
Step 6
Enter the last two digits of the “Year Code”.
Example: For 2007 enter [0]–[7].
SETTING THE SYSTEM CLOCK
Step 1
Press [r]-[9]-[7].
Step 2
Enter the “Master Code “.
Step 3
Enter the “hour code” which must be two (2) digits. Note: The clock
is a 24-hour clock. Refer to the following table.
Step 4
Enter the “minutes code” which must be two (2) digits.
Example: 7 minutes after would be entered [0]–[7].
Time
Hour Code
Time
Hour Code
Time
Hour Code
00
8:00 AM
08
4:00 PM
16
01
9:00 AM
09
5:00 PM
17
2:00 AM
02
10:00 AM
10
6:00 PM
18
3:00 AM
03
11
7:00 PM
19
4:00 AM
04
12
8:00 PM
20
5:00 AM
05
11:00 AM
12:00
Noon
1:00 PM
13
9:00 PM
21
6:00 AM
06
2:00 PM
14
10:00 PM
22
7:00 AM
07
3:00 PM
15
11:00 PM
23
12:00
Midnight
1:00 AM
13
WWW.DIYALARMFORUM.COM
KEYPAD CONTROL TONES (BEEPS)
A sounder is built into the keypad. If programmed, your system keypad may
sound for any of the following reasons:
Beeps for all keypresses.
Sounds a continuous tone during the Entry delay time.
Pulses when a day zone is violated while the system is disarmed.
Pulses when a FIRE zone has a trouble condition.
Beeps 3 times for trying to arm with the “Ready” light off, if “Force Arming”
has not been selected.
Beeps for 1 second or emits a “ding-dong” sound for the “Chime” feature.
Beeps during an exit delay; beeps rapidly for the last 10 seconds of an exit
delay; and beeps 1 second at the end of the exit delay.
Pulses when the armed status changes and the AC power is off.
Pulses when the armed status changes and any zone(s) are bypassed.
Pulses when the armed status changes and a low battery is detected.
Pulses when the armed status changes and a Tamper condition is detected.
Pulses when one or more of the following conditions are detected: Zone or
Box Tamper, Low Battery, AC Power Fail, or Expander trouble.
Entering a valid code will silence the keypad sounder when it is pulsing. The
arm/disarm state of your system will not change when entering a code to silence
a pulsing keypad sounder. Please contact your installer if a trouble condition
exists.
14
WWW.DIYALARMFORUM.COM
SERVICE MENU
The service light will be “on” if the security system requires service. If the service
light is “on”, press the [r] key followed by the [2] key to determine the service
condition. One or more zone lights will illuminate indicating what service(s) is
required. Call your service provider immediately for these problems. Below is a
listing of what each light means in a service condition.
LIGHT
PROBLEM
1
SYSTEM FAULT - Press the [1] key. The zone light(s) that is
illuminated corresponds to the system fault(s) below:
1 Over Current Fault
5 Expander Low Battery
2 Siren Trouble
6 Expander Box Tamper
3 Box Tamper
7 Expander Trouble
4 Expander Power
8 Reserved
Press the [#] key to return to the 1 of 8 service lights.
2
ZONE TAMPER - Press the [2] key and the zone light(s) will
illuminate showing the zone(s) that are tampered. Press the [#] key
to return to the 1 of 8 service lights.
ZONE LOW BATTERY - Press the [3] key. The zone light(s) will
illuminate showing which zone(s) has a low battery. This only
applies to wireless zones. Press the [#] key to return to the 1 of 8
service lights.
ZONE LOSS OF SUPERVISION - Press the [4] key and the zone
light(s) will illuminate showing which zone(s) has loss of
supervision. This only applies to wireless zones. Press [#] key to
return to the 1 of 8 service lights.
ZONE TROUBLE - Press the [5] key and the zone light(s) will
illuminate showing which zone(s) has a trouble condition. Press the
[#] key to return to the 1 of 8 service lights.
RESERVED.
3
4
5
6
7
8
EXIT
FAILURE TO COMMUNICATE - This light will illuminate when there
is a failure to communicate between your system and the central
station.
LOSS OF SYSTEM TIME - This light will illuminate when there has
been a loss of power and your system clock needs to be reset.
Instructions are on page 13.
Press the [#] key to exit the Service Light mode.
15
WWW.DIYALARMFORUM.COM
EMERGENCY EVACUATION PLANS
An emergency evacuation plan should be established for an actual fire alarm
condition. For example, the following steps are recommended by the National
Fire Protection Association and can be used as a guide in establishing an
evacuation plan for your building.
Draw up a floor plan of your home. Show windows, doors, stairs, and rooftops
that can be used for escape. Indicate each occupant's escape routes. Always
keep these routes free from obstruction. Determine two means of escape from
each room. One will be the normal exit from the building. The other may be a
window that opens easily. An escape ladder may have to be located near the
window if there is a long drop to the ground below. Set a meeting place outdoors
for a headcount of the building occupants. Practice escape procedures. In a
home, sleep with bedroom door closed; this will increase your escape time. If
you suspect fire, test the door for heat. If you think it is safe, brace your shoulder
against the door and open it cautiously. Be ready to slam the door if smoke or
heat rush in. Practice escaping to the outdoors and meeting in an assigned spot.
Call the Fire Department from a neighbor's phone.
NOTE: After the installation of your Security System has been completed, notify
your local Fire and Police Departments to give them your name and address for
their records. Early warning fire detection is best achieved by the installation of
fire detection equipment in all rooms. This equipment should be installed in
accordance with the National Fire Protection Association's Standard 72. For
additional information write the National Fire Protection Association,
Batterymarch Park, Quincy, MA 02269.
The following are examples of evacuation plans. A plan unique to your home or
business should be drawn and memorized by each occupant.
16
WWW.DIYALARMFORUM.COM
SYSTEM NOTES
17
WWW.DIYALARMFORUM.COM
NX-4 USER’S MANUAL
NX4UD04
REV D (FEB 2004)
WWW.DIYALARMFORUM.COM