HD CCTV

Digital Video Camera

OPERATION MANUAL

M141-HDX222-001

Thank you for choosing our high quality camera. Before attempting to connect operate this unit, please read and follow these instructions.

CAUTION

These servicing instructions are for use by qualified service personnel only.

To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

Use Class 2 Power Supply Only

2

CONTENTS

1. CAUTIONS

2. IMPORTANT SAFETY INSTRUCTIONS

3. FEATURES

4. EQUIPMENT AND ACCESSORIES

5. CAMERA COMPONENT DESCRIPTIONS

6. INSTALLATION

7. DIMENSIONS

8. SPECIFICATIONS

9. OSD MANUAL

3

1. CAUTIONS

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference

that may cause undesired operation.

Note

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

WARNING

This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Caution

Any changes or modifications in construction of this devices which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

1. A regulated DC12V 500mA power supply is recommended for use with this camera for the best picture and the most stable operation.

An unregulated power supply can cause damage to the camera. When an unregulated power supply is applied, the product warranty will be void.

2. It is recommended that the camera be used with a monitor that has a CCTV quality 75Ω video impedance level. If your monitor is switched to high impedance then please adjust accordingly.

3. Do not attempt to disassemble the camera to gain access to the internal components.

Refer servicing to your dealer.

4. Never face the camera towards the sun or any bright or reflective light, which may cause smears on the picture and possible damage to the Image Sensor.

5. Do not remove the serial sticker for the warranty service.

6. Do not expose the camera to rain or other types of liquid.

7. The apparatus must be connected to a main socket-outlet with a protective earth connection.

4

1. CAUTIONS

WEEE

(Waste Electrical & Electronic Equipment)

This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.

To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract.

This product should not be mixed with other commercial wastes for disposal.

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL

This symbol is intended to alert the user to the presence of un-insulated

“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

5

2. IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long

periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

6

3. FEATURES

• High Resolution

SONY 1/3” 2.1M/P Progressive Color CMOS Image Sensor,

1920x1080 30fps

• Support various digital video output

720p60, 720p50, 1080p30, 1080p25

• Video Outputs

Primary HD-SDI (BNC)

Test/Setup TV Out (Test Point-adapter to BNC included), NTSC/PAL selectable

• OSD menu for setup and configuration

• Lens Control

DC Iris

• Power Source

DC 12V / AC 24V ( Dual Power Type )

DC 12V ( DC Power Type )

7

4. EQUIPMENT AND ACCESSORIES

HD CCTV

Digital Video Camera

Auto Iris Lens

Connection Plug

C-mount Adaptor Ring

Operation Manual

* NOTE

PLEASE REMOVE PROTECTION FILM

8

+ -

5. CAMERA COMPONENT DESCRIPTIONS

• FRONT

TRIPOD MOUNTING HOLE(1/4"-20 UNC)

C-MOUNT ADAPTOR RING

MOUNT COVER

CS-MOUNT ADAPTOR RING

CS-MOUNT ADAPTOR RING FIXING SCREW(2EA)

TRIPOD MOUNTING HOLE(1/4"-20 UNC)

AUTO

IRIS JACK

9

5. CAMERA COMPONENT DESCRIPTIONS

• BACK

➊ ➋ ➎ ➐ ➊ ➋ ➎ ➐

➍

➌

➓

VIDEO

MENU/SET

OFF/ON

HD SDI

OUTPUT

+ -

POWER

VIDEO

➏

➑

➍

➌

➒

➓

DC12V GND

DC12V

① . MENU BUTTON

②

. UP BUTTON

③ . DOWN BUTTON

④

. LEFT BUTTON

⑤ . RIGHT BUTTON

⑥

. POWER LED

(The LED turns on when power is supplied)

⑦ . VIDEO OFF/ON SWITCH

⑧

. HD SDI OUTPUT JACK

⑨ . VIDEO OUT JACK

(Used to connect an external video monitor in jack)

⑩.

POWER TERMINAL

(Used to connect an DC12V power source)

(Options : AC24V / DC12V)

10

VIDEO

MENU/SET

OFF/ON

HD SDI

OUTPUT

POWER

VIDEO

➏

➑

➒

DC12V/AC24V

AC24V / DC12V

6. INSTALLATION

• LENS CONNECTION

Mega Pixel Lenses are sold separately. Lenses such as an auto iris lens,

CS-Mount lens and C-Mount lens can be used (adapter included for C-Mount Lens).

NOTE

• Please keep the lens clean.

• Any foreign objects and Finger marks on the lens can cause

inferior image quality in low light level conditions

.

When using an auto iris lens

1. Please peel off about 8mm

of the outer skin of the auto iris lens cable.

2. Please peel off about 2mm of the outer skin

of the insulated conductor inside the lens cable.

11

6. INSTALLATION

3. Please remove the cover of the auto iris lens connection plug and

solder the lens cable to the connector pin in the plug.

* PIN ASSIGNMENT OF THE LENS CONNECTOR

1) Video auto iris lens

Pin 1: Power source(DC 12V)

Pin 3: Video signal

Pin 4: Shield, GND(Ground)

2) DC auto iris lens

Pin 1: DAMP-(CTL-)

Pin 2: DAMP+(CLT+)

Pin 3: DRV+

Pin 4: DRV-(GND)

4. Please replace the auto iris lens connection plug cover and take off the sensor

protection cap and then attach the auto iris lens to the camera by screwing it in

clockwise.

12

6. INSTALLATION

5. Please insert the connection plug from the auto iris lens cable into the auto

lens connector, which is located on the side of the camera.

* NOTE

Use the lens under the specification as shown.

Otherwise the lens can damage the camera or abnormal fixing may result.

C-mount lens : 10 mm or less

CS-mount lens : 5 mm or less

13

6. INSTALLATION

Installation of C-Mount Lens

C-MOUNT ADAPTOR RING

CS-MOUNT ADAPTOR RING

Installation of CS-Mount Lens

CS-MOUNT ADAPTOR RING

14

6. INSTALLATION

• MONITOR CONNECTION

- DC12V

MENU/SET

VIDEO

OFF/ON

POWER

+ -

VIDEO

HD SDI OUTPUT

DC12V GND

HD SDI INPUT

SDI

RECEIVER

DISPLAY

DEVICE

TV

MONITOR

VIDEO INPUT

DC12V REGULATED

POWER SUPPLY

- DC12V/AC24V

MENU/SET

VIDEO

OFF/ON

HD SDI

OUTPUT

POWER

VIDEO

HD SDI OUTPUT

DC12V/AC24V

HD SDI INPUT

RECEIVER

DEVICE

DC12V / AC24V REGULATED

POWER SUPPLY

15

VIDEO INPUT

CAUTIONS

When you output Video

WDR function does not work

7. DIMENSIONS

Unit(mm)

TRIPOD MOUNTING HOLE

(1/4"-20 UNC, Depth 5)

58

75.5(C-MOUNT)

70.5(CS-MOUNT)

TRIPOD MOUNTING HOLE

(1/4"-20 UNC, Depth 5)

16

8. SPECIFICATION

Image Device

Effective Pixels

Unit cell size

Video Output Mode

Minimum Illumination

S/N Ratio

Shutter Speed

Manual Shutter Speed

Controllable Max Gain

White Balance

Lens Control

OSD Menu

DC

Power

Consumption

DUAL

Weight

Dimension

Conformity

Temperature / Humidity

(no condensing)

SONY 1/3” 2.1M/P Progressive Color CMOS Image Sensor

1984 (H) x 1105 (V) 30fps

2.8um (H) x 2.8um (V)

HD-SDI: 720p60, 720p50, 1080p30, 1080p25

TV Out: NTSC / PAL selectable

0.1 Lux

More than 50dB

Auto / Manual selectable

1/30(25), 1/60(50), 1/120(100), 1/240, 1/500,

1/1K, 1/2K, 1/4K, 1/8K, 1/16K, 1/30K, 1/60K

29 dB

AUTO / AUTOext / PUSH / MANUAL

DC Iris

Yes

DC12V(±10%), Max. 200mA

DC12V(±10%), Max. 270mA

AC24V(±10%), Max. 3.6W

DC12V: 175g, DUAL: 200g

58(W) x 58(H) x 70.5(D)

CE, FCC, KC

Operation: 14°F~122°F(-10°C~+50°C / 20~80%)

Storage: -4°F~158°F(-20°C~+60°C / 20~95%)

Specifications and designs are subject to change for improving the functionality of this product without notice.

17

9. OSD MANUAL

• Menu structure

Main

EXPOSURE

WHITE

BALANCE

WDR / BLC

DNR

DAY &

NIGHT

Sub Menu Sub Menu

BRIGHTNESS 0 ~ 20

AE MODE

LENS(IRIS)

NORMAL AE / INDOOR

MANUAL / AUTO

SHUTTER

MANUAL /

AUTO

LEVEL

RETURN

1/30(25), 1/60(50), 1/120(100), 1/240, 1/500,

1/1K, 1/2K, 1/4K, 1/8K, 1/16K, 1/30K, 1/60K.

BACK / EXIT

DSS

AGC

OFF, X2, X3, X4, X5, X6, X7, X8

0 ~ 10

BASE FREQ 60Hz / 50Hz

RESET DATA BACK / DEF.

RETURN BACK / EXIT.

WB MODE

AUTO

/AUTOext

/PUSH

/MANUAL

COLORTEMP. LOW / MIDDLE / HIGH

R-GAIN

B-GAIN

RETURN

0 ~ 20

0 ~ 20

BACK / EXIT

SATURATION 0 ~ 20

RESET DATE BACK / DEF.

RETURN

MODE

WDR WGT

BLC OSD

BACK / EXIT.

OFF, WDR, BLC, D-WDR

0 ~ 4

OFF ~ ON

BLC POS-X

BLC POS-Y

BLC SIZE-X

BLC SIZE-Y

0 ~ 20

0 ~ 20

0 ~ 20

0 ~ 20

RESET DATA BACK / DEF.

RETURN BACK / EXIT.

OFF, LOW, MIDDLE, HIGH

D&N DETECT AGC

COLOR/

B&W/

AUTO

DELAY 1sec, 3, 5, 10, 15, 20, 25, 30, 40, 50, 60sec

D->N LEVEL 3 ~ 20

N->D LEVEL 0 ~ 16

RESET DATA BACK / DEF.

RETURN BACK / EXIT.

18

9. OSD MANUAL

Main

IMAGE

Sub Menu

SHARPNESS

GAMMA

FLIP

LENS SHADING

DZOOM

RESET DATA

RETURN

SPECIAL

SYSTEM

PRIVACY

HLMASK

PATTERN

RESET DATA

RETURN

SDI FORMAT

SDI FPS

CVBS FORMAT

APPLY

SYSTEM INFO.

Sub Menu

0 ~ 20

0 ~ 4

OFF, H FLIP, V FLIP, HV FLIP

OFF, ON

1x, 2x, 4x, 6x, 8x, 10x, 12x, 14x, 16x, 18x, 20x

BACK / DEF.

BACK / EXIT.

OFF / ON

ZONE NO

ZONE OP

X-POS

Y-POS

X-SIZ

Y-SIZ

COLOR

TRANS.

RESET DATA

RETURN

OFF / ON

OFF / 0 / 1

BACK / DEF.

BACK / EXIT.

LEVEL

COLOR

RESET DATA

RETURN

0 ~ 23

OFF / ON

0 ~ 60

0 ~ 40

0 ~ 40

0 ~ 40

BLK, WHT, YEL, CYN, GRN, MAG, RED, BLU

0 ~ 4

BACK / DEF.

BACK / EXIT.

0 ~ 20

BLK, WHT, YEL, CYN, GRN, MAG, RED, BLU

BACK / DEF.

BACK / EXIT.

1080P / 720P

30(60) / 25(50)

NTSC /

PAL

OK / ON

CVBS OUT

CVBS VIEW

RETURN

S/W VERSION

SET VERSION

AUTO / OFF / ON(WDR OFF)

CROP / FULL

BACK / EXIT.

RETURN BACK / EXIT.

REBOOT

RETURN BACK / EXIT.

19

9. OSD MANUAL

• Function Description

0. SETUP

- EXPOSURE

- WHITE ALANCE : Go sub menu for camera white balance control.

- WDR/BLC

: Go sub menu for camera exposure control.

: Go sub menu for camera WDR or BLC action.

- DNR

- DAY & NIGHT

- IMAGE

- SPECIAL

: Control noise reduction setting.

: Go sub menu for camera day & night control.

: Go sub menu for adjust image functions.

: Go sub menu for special feature control.

- SYSTEM : Go sub menu for system control & information.

- RESET DATA ALL : Reset camera’s all feature data to default value.

1. EXPOSURE

- BRIGHTNESS

- AE MODE

- LENS(IRIS)

- SHUTTER

• LEVEL

- DSS

- AGC

- BASE FREQ

: Adjust image brightness value.

: Adjust AE control mode.

: Select lens iris control type.

: Select shutter speed control type.

: Adjust shutter speed at manual shutter mode.

: Adjust digital slow shutter control level.

: Adjust max gain level for brightness control.

: Select basic control frequency for control camera feature.

2. WHITE BALANCE

- WB MODE

• AUTO

• AUTOext

• PUSH

: Select white balance control mode.

: Full auto control mode in color temperature rage 2300K~10000K.

• MANUAL

◦ COLOR TEMP. : Select color temperature range for WB control at manual mode.

◦ R-GAIN

◦ B-GAIN

- SATURATION

: Extended auto mode for special illumination.

: Enable fix the control setting for specific environment.

Push & release, for fix WB control setting.

: Enable WB control setting by user’s intention.

: Adjust red color gain for WB control at maual mode.

: Adjust blue color gain for WB control at manual mode.

: Adjust color saturation level.

20

9. OSD MANUAL

3. WDR/BLC

- MODE

• WDR

• BLC

• D-WDR

- WDR WGT

- BLC OSD

- BLC POS-X

- BLC POS-Y

- BLC SIZ-X

- BLC SIZ-Y

: Select WDR / BLC mode.

: Act in wdie dynamic rage mode. Controled video frame rate in 1/2.

: Act in Backlight compensation mode.

: Digital wide dynamic range control.

: WDR weight control level settig at WDR mode.

: Display BLC control zone in screen.

: Select BLC control zone vertical position.

: Select BLC control zone horizontal position.

: Select BLC control zone vertical size.

: Select BLC control zone horizontal size.

4. DNR: Reduce image’s noise

5. DAY & NIGHT

- MODE

• AUTO

: Select TDN(True Day & Night control) mode.

: Camera controlled automatically to decide day or night environment

using AGC calculation data or input level data from CDS sense.

• COLOR : Fix to mode at day environment setting.

• B&W

Make video image act in color.

: Fix to mode at night environment setting.

Make video image act in B/W.

■ D/N DETECT : Fixed selection to AGC for TDN auto control.

■ DELAY

: Delay time for change day or night mode at auto mode.

■ D->N LEVEL : Threshold level for change Day to Night mode.

■ N->D LEVEL : Threshold level for change Night to Day mode.

6. IMAGE

- SHARPNESS

- GAMMA

- FLIP

: Adjust image sharpness level.

: Gamma curve select.

: Vertical & Horizontal flip setting.

- LENS SHADING : Enable lens shading compensation.

- DZOOM : Select digital zoom magnification.

21

9. OSD MANUAL

7. SPECIAL

- PRIVACY

• ZONE NO.

• ZONE OP.

• X-POS

• Y-POS

• X-SIZ

• Y-SIZ

• COLOR

• TRANS.

- HLMASK

• LEVEL

• COLOR

- PATTERN

8. SYSTEM

- SDI FORMAT

- SDI FPS

- CVBS FORMAT

• CVBS OUT

◦ ON, OFF

◦ AUTO

• CVBS VIEW

◦ CROP

◦ FULL

: Setting for protect private area in image using mask setting.

: Select private mask zone number.

: Select zone mask display on/off.

: Select zone horizontal position.

: Select zone vertical position.

: Select zone horizontal size.

: Select zone vertical size.

: Select mask color

: Select mask transparency level.

: Mask image high light area.

: Select high light level.

: Select mask color.

: Color bar display select.

: 1080P / 720P

: 30 or 25 fps in 1080p mode.

60 or 50 fps in 720p mode.

: NTSC / PAL

: Select mode for CVBS out action.

: Enable or Disable CVBS out data.

: Check automatically CVBS video cable connection.

If connected, CVBS out data is enable and WDR mode

is setted off automatically.

: CVBS out video angle setting.

: Cut the scene outside area for keep image aspect ratio.

: Fill the full angle scene into image with

H-V size & ratio change.

: Apply all video angle setting. Use the set button to apply.

- APPLY

- SYSTEM INFO.

• S/W VERSION

• SET VERSION

: Camera’s basic software version.

: Camera’s feature control setting version.

22