UHD6G-200

Micro UHD 6G-SDI EFP Camera

Operation Guide

Ver. 1.0 / MAR 2018

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Warning

This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.

Precaution

This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Warning

To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to rain or moisture.

3.

4.

1.

2.

Be sure to use only the standard adapter that is specified in the speci fi cation sheet. Using any other adapter could caus e fire, electrical shock, or damage to the product.

Incorrectly connecting the power supply or replacing battery may cause e x plosion , fire, ele ctric sho ck, or damage to the product.

Do not connect multiple cameras to a single adapter. Ex ceeding the capacity may cau se ex cessive heat or fire.

Securely plug the power cord into the power receptacle. Insecure connection may cause fire.

2

5.

6.

When installing the camera, fasten it securely and firmly. A falling camera may cause personal injury.

Do not place conductive ob j ects (e.g. screw drivers , c oins , metal item s, etc.

) or container s fi lled with water on top o f the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects.

Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.

7.

8.

9.

10.

If any unusual smells or smoke come from the unit, stop using the product. Immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fire or electric shock.

If this product fails to operate normally , contact the nearest service center. Never disassemble or modify this product in any way.

When cleanin g, do not spray water directly onto parts of th e product. Doing so may cause fire or electric shock.

Precaution

Please read this Operation Guide before installing and using the camera & retain this copy for your reference.

1.

Always follow the instructions in the operations guide when applying power. Fire and equipment damage can occur if power is applied incorrectly. For the correct power supply,refer to the specifications page.

2.

3.

4.

5.

6.

Do not use camera if fumes, smoke or a strange odor is emitted from the camera, or if it seems not functional correctly. Disconnect the power source immediately and consult with your supplier.

Do not use the camera in extreme environments where high temperatures or high humidity exists. Use the camera under conditions where temperatures are between 32°F ~ 104°F, and humidity is below 90%.

If installed close to a TV, radio transmitter, magnet, electric motor transformer or audio speakers the magnetic field generated may interfere with or distort the image.

Try to avoid fluorescent light reflections, unstable light conditions, direct pointing toward the sun. Use caution when operating the camera in the vicinity of spotlights or other bright lights and light reflecting objects.

To prevent damage, do not drop the camera or subject it to strong shock or vibration.

3

4

UHD6G-200

FRONT

Tripod

Mounting

Hole

SDI OUT

CS-Mount

Holding

Screw

AUTO IRIS Lens

Connector

I/O Connector Cable

REAR

I/O: Power, OSD,

RS-485, Audio

POWER LED

Power In

Audio In

U

L

R

D

485

+ -

OSD Controller

RS-485

RS-485 +

RS-485 -

12VDC

FEATURES

4K UHD 1/2.5 Progressive Scan CMOS sensor captures sharp and vivid UHD video even under very low light conditions.

Advanced digital imaging processor provides vivid and detailed images by utilizing

Dynamic Range, Auto White Balance, and Noise Reduction.

Superb motion-compensated temporal noise reduction filter for motion video without blurring.

OSD control breakout cable with audio input and RS-485 for remote communication.

Flawlessly relays multi-channel embedded audio via SDI output.

Interchangeable lens design compatible with CS and C mount lenses.

Perfectly suited for broadcast, pro audio/video, and security.

Conforming with SMPTE 292M, 424M and 2081-10

Versatile, compact, and rugged design.

5

6

OSD MENU

MAIN MENU

* EXPOSURE

WHITE BALANCE

DAY & NIGHT

DNR

PRIVACY

EFFECT

SPECIAL

SETUP

EXIT

>

>

>

>

>

>

>

>

UP

LEFT

U R

L D

485

+ -

RIGHT

SEL

DOWN

1

Move the Cursor Up/Down to Choose Menu

To move from item to item in the menu, move the joystick to the Up/Down.

2

Change the Value

To change the value of the selected item, move the joystick to the Left/Right.

3

Shift to the Sub Menu of the Chosen Menu

To go into sub menu, press SEL key.

EXPOSURE

*

AE MODE

SHUTTER

IRIS

AGC

AGC MAX

SENS UP

AE BRIGHT

IRIS SPEED

LENS MODE

FLK CONTROL

RETURN

AUTO

HIGH

OFF

6

3

INDOOR

AUTO

EXPOSURE

AUTO

Auto mode will adjust the exposure level automatically.

Detailed fine tuning options are available under this menu.

AGC MAX : OFF, LOW, MIDDLE, HIGH, DMIN, DMID, DMAX

“AGC MAX” sets the maximum gain value to control the video noise caused by Auto Gain Control.

SENS UP : OFF, x2 ~ x10

“SENS UP” mode controls the digital slow shutter to allow extra light into the camera and adjust the picture quality.

AE BRIGHT : 0~20

Auto Exposure brightness level can be adjusted.

7

8

EXPOSURE

EXPOSURE

*

AE MODE

SHUTTER

IRIS

AGC

AGC MAX

SENS UP

AE BRIGHT

IRIS SPEED

LENS MODE

FLK CONTROL

RETURN

SHUT FIX

AUTO

HIGH

OFF

6

3

INDOOR

AUTO

SHUT FIX

SHUT FIX mode provides more detailed shutter speed option.

All other controls are tuned for the selected shutter speed.

SHUTTER : AUTO, 1/30 ~ 1/10,000

Shutter speed can be set.

AGC MAX : OFF, LOW, MIDDLE, HIGH, DMIN, DMID, DMAX

“AGC MAX” sets the maximum gain value to control the video noise caused by Auto Gain Control.

SENS UP : OFF, x2 ~ x10

“SENS UP” mode controls the digital slow shutter to allow extra light into the camera and adjust the picture quality.

AE BRIGHT : 0~10

Auto Exposure brightness level can be adjusted.

EXPOSURE

*

AE MODE

SHUTTER

IRIS

AGC

AGC MAX

SENS UP

AE BRIGHT

IRIS SPEED

LENS MODE

FLK CONTROL

RETURN

AGC FIX

AUTO

HIGH

6

3

INDOOR

AUTO

EXPOSURE

AGC FIX

AGC FIX mode provides more detailed gain option.

All other controls are tuned for the selected gain value.

AGC : AUTO, 0dB ~ 27dB, d2X ~ d9X

Gain level can be set.

AGC MAX : OFF, LOW, MIDDLE, HIGH, DMIN, DMID, DMAX

“AGC MAX” sets the maximum gain value to control the video noise caused by Auto Gain Control.

AE BRIGHT : 0~10

Auto Exposure brightness level can be adjusted.

9

10

EXPOSURE

EXPOSURE

*

AE MODE

SHUTTER

IRIS

AGC

AGC MAX

SENS UP

AE BRIGHT

IRIS SPEED

LENS MODE

FLK CONTROL

RETURN

AUTO

HIGH

OFF

6

3

INDOOR

AUTO

IRIS SPEED : 0 ~ 5

Electronic Iris speed can be controlled. (DC Iris lens only)

LENS MODE : INDOOR, OUTDOOR, MANUAL

Lens setting will be optimized for the selected environment.

(DC Iris lens only)

FLK CONTROL : AUTO, ON, OFF

“FLK CONTROL” mode provides a proper image sensor frequency to match the power frequency in order to minimize video flicker.

WHITE BALANCE

*

MODE

PUSH

BLUE

RED

SPEED

OFFSET-B

OFFSET-R

RETURN

ATW

6

52

54

WHITE BALANCE

* MODE

PUSH

BLUE

RED

SPEED

OFFSET-B

OFFSET-R

RETURN

ONE PUSH

PRESS OK

52

54

WHITE BALANCE

ATW

Auto white balance mode will adjust white balance within 1,900°K ~

11,000°K temperature.

SPEED : 0 ~ 7

White balance adjust speed can be adjusted.

OFFSET-B : 0 ~ 100

“OFFSET-B” adjusts Blue gain within the range of 0 to 100.

OFFSET-R : 0 ~ 100

“OFFSET-R” adjusts Red gain within the range of 0 to 100.

ONE PUSH

“ONE PUSH” mode is used if “ATW” cannot produce the proper white balance.

PUSH

Press Select button to enable “ONE PUSH” white balance adjustment.

Place a white paper in front of the camera when using the “ONE PUSH” mode to self-adopt.

Camera provides a wide range of white balance options. Check your color temperature before adjusting this mode.

11

12

WHITE BALANCE

WHITE BALANCE

*

MODE

PUSH

BLUE

RED

SPEED

OFFSET-B

OFFSET-R

RETURN

INDOOR

6

52

54

WHITE BALANCE

*

MODE

PUSH

BLUE

RED

SPEED

OFFSET-B

OFFSET-R

RETURN

MANUAL

50

50

INDOOR

“INDOOR” mode will adjust white balance to indoor lighting condition.

OUTDOOR

“OUTDOOR” mode will adjust white balance to outdoor lighting condition.

MANUAL

“MANUAL” mode will adjust white balance manually.

BLUE : 0 ~ 100

Select Blue gain within the range of 0 to 100.

RED : 0 ~ 100

Select Red gain within the range of 0 to 100.

DAY & NIGHT

*

MODE

NIGHT COLOR

COLOR BURST

RETURN

DAY (COLOR)

OFF

OFF

DAY & NIGHT

Adjust color or B&W setting from this menu.

MODE : DAY(COLOR), NIGHT(B&W)

Set camera to either color mode or B&W mode.

NIGHT COLOR : ON, OFF

When “NIGHT COLOR” is turned ON, camera stays on color mode even “NIGHT(B&W)” is selected from the MODE.

COLOR BURST : ON, OFF

Color burst signal ON or OFF can be set for CVBS signal.

(Not applicable)

13

14

DNR

NOISE REDUCTION

*

MODE

DNR LEVEL

DNR APERTURE

RETURN

2D + 3D

AUTO

2

NOISE REDUCTION

Camera noise level can be adjusted from this menu.

DNR MODE : OFF, 2D, 3D, 2D+3D

Digital noise reduction can be applied from this menu.

DNR LEVEL : AUTO, LOW, MIDDLE, HIGH

Noise reduction level can be adjusted from this menu.

DNR APERTURE : 0 ~ 4

Motion artifacts tightness can be adjusted.

0 = Most ghost artifact 4 = Least ghost artifact

PRIVACY MASK

*

MODE

TYPE

MASK NO.

DISPLAY

POLY SELECT

POSITION-X

POSITION-Y

SIZE-X

SIZE-Y

DEFAULT

RETURN

ON

SQUARE

MASK 1

ON

WHITE

L-TOP

22

38

PRIVACY

Privacy zone can be setup from this menu.

MODE : ON, OFF

Enable “PRIVACY ZONE” ON or OFF.

TYPE: SQUARE, POLYGON

Select privacy zone shape.

MASK No : MASK1 ~ MASK8

Select privacy zone mask number.

DISPLAY : ON, OFF

Turn ON or OFF the selected privacy mask zone.

COLOR : WHITE, GREEN, BLUE, RED, CYAN,

MAGENTA, YELLOW, GRAY-1 ~ 6, MOSAIC, BLACK

Select privacy zone mask color.

POLY SELECT : L-TOP, L-BOTTOM, R-TOP,

R-BOTTOM

Change the shape of the polygon by selecting the corner of the polygon.

POSITION-X & POSITION-Y

Change the size of the selected corner from “POLY SELECT” menu.

SIZE-X & SIZE-Y

Change the size of the privacy square.

DEFAULT

Set privacy zone to default value.

15

16

EFFECT

Camera image control can be adjusted from EFFECT menu.

*

*

EFFECT

LENS SHADING

GAMMA CORRECT

CONTRAST

BRIGHTNESS

SATURATION

HUE

EDGE ENHANCE

AUTO SATURATION

AUTO EDGE

DEFAULT

RETURN

GAMMA CORRECTION OPTION

FRONT GM EN

REAR GM EN

REAR GM INV

BAY LUT EXTEND

RGB LUT EXTEND

Y LUT EXTEND

BYLUT XSAMPLE

RGBLUT XSAMPLE

RETURN

ON

ON >

11

11

12

10

5

MIDDLE

ON

LENS SHADING : ON, OFF

Optical vignetting issue can be corrected from this menu.

GAMMA CORRECT: ON, OFF(1.0)

Gamma level can be adjusted.

FRONT GM EN : DEFAULT, OFF-BYPASS, 0.9 ~ 0.4, CUSTOM

CMOS sensor gamma level can be adjusted.

REAR GM INV : DEFAULT, OFF, 0.9 ~ 0.4, CUSTOM

Output gamma level can be adjusted.

DEFAULT

DEFUALT

UNIFORM

UNIFORM

UNIFORM

64x256LUT

64x256LUT

Y LUT EXTEND : UNIFORM, EXTEND-F2C

Tuning and engineering purpose LUT correction.

BYLUT XSAMPLE : 64x256LUT, 32x256LUT, 64x256LUT,

128x256LUT, 256x256LUT

Tuning and engineering purpose LUT correction.

RGBLUT XSAMPLE : 64x256LUT, 32x256LUT, 64x256LUT,

128x256LUT, 256x256LUT

Tuning and engineering purpose LUT correction.

EFFECT

EFFECT

*

LENS SHADING

GAMMA CORRECT

CONTRAST

BRIGHTNESS

SATURATION

HUE

EDGE ENHANCE

AUTO SATURATION

AUTO EDGE

DEFAULT

RETURN

ON

ON > BRIGHTNESS:

11

11

CONTRAST : 0 ~ 20

Contrast level can be adjusted.

0 ~ 20

Brightness level can be adjusted.

12

10

5

SATURATION : 0 ~ 20

Saturation level can be adjusted.

MIDDLE

ON

HUE: 0 ~ 20

Hue level can be adjusted.

EDGE ENHANCE : 0 ~ 20

Image sharpness level can be adjusted.

AUTO SATURATE: OFF, LOW, MIDDLE, HIGH

Decrease saturation automatically when noisy scene is detected.

AUTO EDGE : ON, OFF

Decrease edge enhancement (sharpness) automatically when noisy scene is detected.

DEFAULT

Set EFFECT menu to default value.

17

18

SPECIAL

SPECIAL

* DZOOM

DEFOG

DIS

BACKLIGHT

BINNING

DEFECT PIXEL

DISP. FUNCTION

FLICKER DETECT

RETURN

ON >

OFF

OFF

OFF

ON >

D-ZOOM

*

ZOOM CONTROL

PIP

PIP SIZE

PIP POSITION

DEFAULT

RETURN

>

ON

1/16

Camera special functions can be adjusted from SPECIAL menu.

DZOOM

: ON, OFF

Digital Zoom and PIP function can be enabled from this menu.

ZOOM CONTROL: RATIO, POSITION, RETURN

Adjust the digital zoom ratio and position.

Use LEFT / RIGHT button to adjust the ratio, then press select.

USE LEFT / RIGHT/ UP / DOWN button to adjust the image position, then press select.

Press select to exit.

PIP : ON, OFF

Turn ON or OFF the PIP window.

PIP SIZE: : 1/16, 1/25

Change the size of PIP window.

PIP POSITION : POSITION, RETURN

Adjust the PIP window location.

USE LEFT / RIGHT/ UP / DOWN button to adjust the image position, then press select.

Press select to exit.

DEFAULT

Set privacy zone to default value.

DEFOG SETUP

*

STRENGTH

THRESHOLD

AUTO LEVEL

RETURN

8

BACKLIGHT - BLC

*

BLC

SIZE/POSITION

DISPLAY

DEFAULT

RETURN

ON

>

ON

SPECIAL

DEFOG

: ON, OFF, AUTO

“DEFOG” menu improves foggy image.

STRENGTH : 0 ~ 16

Change defog strength.

THRESHOLD : 0 ~ 3

Threshold value sets minimum sensitivity value for automatic defog control. Higher value makes defog-on control reluctant.

AUTO LEVEL : LOW, MID, HIGH

Auto level value sets maximum strength value for automatic defog control. Higher value makes defog effect to be stronger.

DIS

: ON, OFF

Digital image stabilization can be turned ON or OFF.

BACKLIGHT

: OFF, BLC, HLM

Camera backlight compensation can be adjusted.

BLC

: OFF, ON

BLC enables back light compensation.

SIZE/POSITION : SIZE, POSITION, RETURN

Adjust BLC area window size.

DISPLAY : OFF, ON

BLC area display can be turned ON or OFF.

DEFAULT

Set BLC menu to default value.

19

20

SPECIAL

BACKLIGHT - HLM

*

AREA

AREA DISPLAY

SIZE/POSITION

LEVEL

BLACK MASK

DEFAULT

RETURN

DEFECT PIXEL

*

STATIC PROGRESS

DETECT SHUT LV

SDPC UPDATE

SDPC CLER

DDPC AUTO PARA

DDPC THHD1

DDPC THHD2

DDPC SEL MODE

DPC DEBUG DISP

RETURN

>

3

ON

HLM

: OFF, ON

HLM can be adjusted.

AREA DISPLAY : ON, OFF

HLM AREA DISPLAY can be turned ON or OFF.

SIZE/POSITION : SIZE, POSITION, RETURN

Adjust BLC area window size.

LEVEL : 0 ~ 20

BLACK MASK : OFF, ON

Masking area highlight can be turned ON or OFF.

DEFAULT

Set HLM menu to default value.

PRESS OK

DEFULT

PRESS OK

PRESS OK

PWR-0

15

15

0

OFF

BINNING

: OFF, ON

Binning can be turned ON of OFF.

DEFECT PIXEL

: OFF, ON, ON(FIXED), STATIC

Defective Pixel Correction feature can be operated.

It is turned ON by default and will run both dynamic and static DPC function.

DISPLAY FUNCTION

*

FREEZE

MIRROR

IMAGE EFFECT

ROTATION

PICTURE STYLE

RETURN

OFF

MIRROR

NEGATIVE

ROT

VIVID

SPECIAL

*

DZOOM

DEFOG

DIS

BACKLIGHT

BINNING

DEFECT PIXEL

DISP. FUNCTION

FLICKER DETECT

RETURN

OFF

OFF

OFF >

RT ZOOM

ON

SPECIAL

DISPLAY FUNCTION

Adjust image display features from this menu.

FREEZE : OFF, ON

Image freeze can be turned ON or OFF.

MIRROR : OFF, MIRROR, V-FLIP, BOTH(H/V)

IMAGE EFFECT : OFF, NEGATIVE, GREY MODE,

REDDISH-1 ~ 4, BLUISH-1 ~ 4, GREENISH-1 ~ 4.

Several color effects can be applied.

ROTATION : OFF, ROT_L FULL, ROT_L 1:1,

ROT_R Full, ROT_R 1:1

Image can be rotated either left or right side.

PICTURE STYLE : OFF, STANDARD, VIVID,

CLEAR, VIVID CLEAR, NEUTRAL,

Different types of picture style can be applied.

FLICKER DETECT

: OFF, ON

“FLICKER DETECT” mode provides a proper image sensor frequency to match the power frequency in order to minimize video flicker.

21

22

SETUP

SETUP

*

CAM TITLE

RS485

MENU COLOR

FACTORY RESET

SYSTEM INFO

OUTPUT FORMAT

AUDIO

RETURN

OFF

>

>

>

>

1080P60 >

Camera setup can be adjusted from this menu.

CAM TITLE : OFF, ON

Camera title can be turned ON or OFF.

RS-485

VISCA communication control can be adjusted.

CAM ID : 0 ~ 7

ID DISPLAY : OFF, ON

BAUDRATE : 2400, 4800, 9600, 19200, 38400

MENU COLOR

OSD menu color can be adjusted.

SYSTEM INFO

Camera information can be found under this menu.

OUTPUT FORMAT

Camera resolution and frame rate can be set.

Supported formats are:

4K2160P 30 / 29.97 / 25 / 24

720P

1080i

1080P

60 / 59.94 / 50

60 / 59.94 / 50

60 / 59.94 / 50 / 30 / 29.97 / 25 / 24

AUDIO

Audio input [MIC or LINE] can be selected, and level can be adjusted under this menu.

SPECIFICATION: UHD6G-200

Image Sensor

Sensor Size

Effective Pixels

Pixel Size

Sync System

Resolution

Minimum Illumination

Frame Rate

Video Signal Output

White Balance

Lens Mount

Synchronization

Audio Input

Audio Sample Rate

Color Space

Other Features

Camera Control

Operation Temperature

Dimension & Weight

Power Requirements

1/2.5 inch Progressive CMOS

Diagnal 7.20mm

Horizontal: 3840, Vertical: 2202

1.62 µm (H) x 1.62 µm (V)

Internal Sync.

2160p : 3840 x 2160

1080p / 1080i : 1920 x 1080

720p : 1280 x 720

0.2Lux (Day), 0.05Lux(Night)

4K2160p : 30 / 29.97 / 25 / 24

1080p : 60 / 59.94 / 50 / 30 / 29.97 / 25 / 24

1080i : 60 / 59.94 / 50

720p : 60 / 59.94 / 50

6G-SDI

Auto & Manual (1,900°K~11,000°K)

C / CS Mount

-

3.5mm Analog Audio Input

16 / 20 / 24 / 32 bits

4:2:2(YCbCr) 10bit

Digital Zoom, DNR, GAMMA CORRECT

OSD Control Button / via RS-485

32°F - 104°F

38mm x 38mm x 65mm / 1.49" x 1.49" x 2.55"

12VDC (+9 - +15VDC)

Specifications are subject to change without notice 23

Disposal of Old Appliances

1. When this crossed-out wheel bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.

2. All electrical and electronic products should be disposed of separately form the municipal waste stream stream in accordance to laws designated by the government or the local authorities.

3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.

4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful inte rference in which case the user will be required to correct the interferenece at his own expense.