ABSCO SHEDS A30231GK Assembly & Instruction Manual

Absco Industries

Aviary Model: A30231GK

FRONT: 3.00m

SIDE : 2.22m

HEIGHT: 2.10m

2320

CONCRETE SLAB

3100mm

WHEN LAYING YOUR CONCRETE

SLAB, ENSURE THERE IS A

REBATED EDGE 25mm DEEP

AROUND THE PERIMETER

THIS WILL HELP WATER EGRESS

FROM THE BASE OF THE SHED

CONCRETE

BOTTOM CHANNEL

REBATED EDGE

75mm WIDE REBATE

CONCRETE SLAB

We thank you for choosing an Australian made shed. For further assistance please visit our detailed instructional video library at

Http://www.abscosheds.com.au/watch-videos

At ABSCO Industries we are always looking to be number ONE, so please let us know what you think of our instructions. Feedback makes us better.

[email protected]

ABSCO INDUSTRIES ASSEMBLY INSTRUCTION MANUAL AVIARY MODEL: A30231GK 06-02-2018 PAGE 01



GENERAL INSTRUCTIONS

· Before commencing any assembly, read through these instructions in detail to gain a thorough understanding of assembly methods and associated details.

· Unpack the carton and carefully identify and check off all the parts against the parts described and illustrated on pages three and four.

SITE PREPARATION

· The site for the shed must be level. An uneven surface may result in misalignment of parts.

· It is recommended that the shed be set on a 100mm concrete slab and anchored down appropriately (refer to last page for details).

· Anchor sets are not supplied as standard items with this product as some customers wish to use their own anchoring systems.

TOOLS REQUIRED TOOLS OPTIONAL

10mm

(Steel)

10mm

(Masonary)

A NOTE ON SAFETY

· Some parts may have sharp edges. It is advisable to wear gloves when handling these items and safety glasses if drilling holes. Sensible shoes are highly recommended.

· Do not erect your shed in windy conditions, ensure that the shed is securely anchored to a solid foundation immediately after construction is completed.

· It is highly recommended to erect the shed with two or more people.




QTY

4

COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS

COMPONENT

DESCRIPTION

PART

No.

CHECK QTY

STEEL SHEET

1785mm X 773mm

30A

5

COMPONENT

DESCRIPTION

MESH SHEET

1220mm X 712mm

PART

No.

CHECK

-

2

STEEL SHEET

1785mm X 773mm

31A

1

MESH SHEET

590mm X 712mm

-

6

2

3

1

STEEL SHEET

1546mm X 773mm

45A

STEEL SHEET

1785mm X 731mm

33A

STEEL SHEET

585mm X 773mm

154

STEEL SHEET

585mm X 773mm

154L

STEEL SHEET

585mm X 773mm

154R 1

2

BRACE

L: 393mm

1

FITTINGS AND

ACCESSORIES

(SEE PAGE 5)

13A

1

PRE-ASSEMBLED

DOOR

-

1

1

RIDGE

BEAM

L = 1152mm

97BL

RIDGE

BEAM

L = 1152mm

97BR

1

2

RIDGE BEAM JOINER

L: 450mm (17.7")

GABLE L/H

L=1475mm

ZARSP

16L

2

GABLE R/H

L=1475mm

16R

1

A30231GCP

CHANNEL PACK

(SEE PAGE 4)




QTY

COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS

COMPONENT

DESCRIPTION

PART

No.

CHECK QTY

COMPONENT

DESCRIPTION

PART

No.

CHECK

2

CHANNEL

L = 1496.5mm

160L

2

CHANNEL

L = 1496.5mm

160R

1

CHANNEL

L = 1496.5mm

1

CHANNEL

L = 1496.5mm

2

CHANNEL

L = 1126.5mm

2

CHANNEL

L = 1105mm

77BL

81BL

81CL

168L

1

CHANNEL

L = 1496.5mm

1

CHANNEL

L = 1496.5mm

2

CHANNEL

L = 1126.5mm

2

CHANNEL

L = 1105mm

77BR

81BR

81CR

168R

2

CHANNEL

L = 1105mm

2

CHANNEL

L = 1126.5mm

13

CHANNEL

L = 712mm

2

CHANNEL

L = 1745mm

11

JAMB L= 1785mm

169L

78BL

181

172

191

2

CHANNEL

L = 1105mm

2

CHANNEL

L = 1126.5mm

1

JAMB L= 1785mm

1

JAMB L= 712mm

4

LIP TRIM L= 1546mm

169R

78BR

192

195

87B




COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS

2

CONTENTS OF FITTINGS PACKET

CAP GABLE

L: 170mm

14A

1 ASSEMBLY

INSTRUCTIONS

12

10

1

1

1

6

CHANNEL JOINER

L= 200mm (7.9")

CSJ

1

SINGLE DOOR

FITTINGS PACK

PSTKSGL

16mm TEK

SCREWS

FAST014 100

LARGE FLANGE

POP-RIVETS

PSTKSGL - SINGLE DOOR FITTINGS PACK

DOOR

PADBOLT

3mm DRILL BIT

FAST006

DRILL

1

1

DOOR

PADBOLT

HASP

FAST007

PHILLIPS DRIVER BIT

FAST038

SELF TAPPING SCREWS

PACKET CONTAINING 220

1

PACK 6P - SCREW PACK 6

3/16 COUNTERSUNK

SCREWS & NUTS

6

PACK 6P

SCREW PACK 6

3.2 x 8mm

BLIND POP RIVETS




INSTRUCTIONS FOR JOINING SPLICED CHANNELS

NOTE: THE TEXT MARKED ON ALL PARTS MUST BE SHOWN ON THE SAME SIDE AS EACH OTHER.

=

JOIN>>

CSJ

=

<<JOIN

=

JOIN>>

J

=

=

JOIN>> SJ

=

STEP 1.

Position the channels and the CSJ joiner channel so the center of the

CSJ is in line with the end of each channel to be joined together.

STEP 2.

Join the first channel to the CSJ by inserting the center of the CSJ (on an angle) to the end of the channel where the JOIN>> text is marked. Push down one side of the CSJ until you hear a 'click'.

=

JOIN>>

=

<<JOIN

JOIN>>

=

<<JOIN

=

STEP 3.

Join the second channel to the CSJ by positioning the <<JOIN end of the channel at the center of the CSJ

(on an angle). Push the CSJ into the channel until you here a 'click'.

FINISHED CHANNEL

The joined channels should now look like the picture above with the

CSJ positioned equally inside of the joined channels.

DRILL 4 x 3mm (2 PER A SIDE)

HOLES TO SECURE SECTIONS

TOGETHER.

(THESE SCREWS MAY HAVE TO

BE TEMPORARILY REMOVED

AND REPLACED DURING LATER

ASSEMBLY)

QTY = 10pcs.

CSJ

CSJ CSJ CSJ

CSJ

HIGH-SIDE

LOW-SIDE

CHANNEL

CHANNEL

ABSCO INDUSTRIES

20mm

CHANNEL

15mm

CSJ

CHANNEL

ASSEMBLY INSTRUCTION MANUAL AVIARY MODEL: A30231GK 06-02-2018 PAGE 06



STEP 1. PRE-ASSEMBLY OF SPLICED CHANNELS

NOTE: JOIN TOGETHER 24 X CHANNEL SECTIONS USING 12 X CHANNEL JOINERS (PART CSJ)

NOTE: SOME CHANNELS HAVE

HOLES IN THEM - YOU WILL NEED

TO RE-DRILL HOLES ON ANY

CHANNEL WHERE THE CSJ

JOINING CHANNEL COVERS

HOLES ON THE CHANNELS

YOU ARE CONNECTING

2993mm (117.8")

81BR

=

=

1 x 81B

1 x 77B

77BR

= 2 x 160

81BL

160R

1 X 81BR

1 X 81BL

77BL

= 2 x 81C

1 X 77BR

1 X 77BL

2 X 160R

2 X 160L

160L

2253mm (88.7")

81CR

78BR

= 2 x 78B

81CL

2 X 81CR

2 X 81CL

= 2 x 168

78BL

168R

2 X 78BR

2 X 78BL 2210mm (87")

= 2 x 169

169R

168L

2 X 168R

2 X 168L

2 X 169R

2 X 169L


169L




INSTRUCTIONS FOR JOINING SPLICED RIDGE BEAM

STAGE 1: PUSH RIDGE BEAMS TOGETHER, MAKE SURE THERE IS A 50mm OVERLAP

OF THE RIDGE CAP

STAGE 2: INSERT RIDGE CAP JOINER INTO CONNECTED RIDGE CAPS.

MAKE SURE JOINER HAS 225mm IN EACH RIDGE CAP.

STAGE 3: TURN RIDGE CAP OVER AND MEASURE 250mm FROM THE END OF EACH RIDGE

CAP.

PLACE TEK SCREWS IN 50mm INCREMENTS FROM SAID END.

REPEAT THIS PROCESS FOR THE OPPOSING HALF OF RIDGE BEAM


QTY. = 1

QTY. = 8

QTY. = 2



STEP 2. PRE-ASSEMBLY OF SPLICED RIDGE BEAM

PHILLIPS DRIVER BIT

SELF DRILLING TEK SCREW

RIDGE BEAM 1126.5mm

PARTS 97BL & 97BR

QTY. = 1

PART ZARSP - 450mm LONG

16mm

ZARSP

200mm

250mm

97BR

16mm


97BL

THE TOP SECTIONS OF

CAPPING WILL OVERLAP

EACH OTHER AT THE

JOIN BY 50mm.

(PART 97B)

2253mm OVERALL LENGTH





16L

16R

16R

16L






ABSCO ASSEMBLY INTRODUCTION

The snaptite assembly system locks most perimeter channels to all roof and wall sheets without the need for tools and fasteners.

SNAP

To pre-assemble the four wall panels and two roof panels, the perimeter channels are secured to the top and bottom of each panel using the snaptite system, as detailed on the following pages wherever you see the symbol.

SNAP

HIGH SIDE

After joining sheets together, position channel over one end of the sheets, gently tapping it over the snaptite lugs, working along the sheets to the other end.

PUSH

PUSH

Position sheets on timbers, trestles or partly over edge of concrete slab.

HIGH SIDE

Each perimeter channel must finish flush with the edges of the sheets.The snaptite system allows adjustment for this process by simply tapping the channel along the sheets until each end is neatly flush. If you need to remove channels from the panels, pull the channel along the panel from

FASTENING SYMBOLS

D opposing ends. You may need someone to help with this.

Join components together by pre-drilling the holes first. Use one component as a template to mark where 3mm POP RIVETS the holes are. Drill with 3mm drill bit.

4mm NUT & BOLT SET

Join components together with one screw at this location only, as some channel sections have extra holes that are not required for this model of garden shed

Do not join components together at this location yet, as the screw may obstruct further assembly of other components




REAR PANEL ASSEMBLY

30A

31A

31A

30A

77B

SNAP i

SNAP i

81B




ROOF PANEL ASSEMBLY

(2 Required)

45A

45A

SNAP i

78B

45A

87B

2 x PRE-PUNCHED

HOLES TO THIS

END OF EACH

SHEET WITH PART

NO. 81C FITTED

81C

SNAP i

87B




SIDE PANEL ASSEMBLY

LEFT HAND SIDE 169

SNAP i

181

SMALL PAN

THIS SIDE

191

191

181

172

154

33A

30A

STEP 2.

JOIN THE TWO SHEETS

TOGETHER (30A & 33A) AT

PRE-PUNCHED LOCATIONS AND

FIT THE TOP AND BOTTOM

CHANNELS (168 & 169). ENSURE

THAT THE PRE-PUNCHED HOLES

IN THE CHANNELS ARE LOCATED

AT THE RIGHT HAND END FOR

CONNECTING THE REMAINING

JAMB AND CORNER MULLION. THE

TOP AND BOTTOM CHANNELS

WILL EXTEND PAST THE CORNER

MULLION BY 3mm.

SNAP i

STEP 1.

JOIN THE JAMB AND

CHANNEL SECTIONS

(191 & 172) TOGETHER

AT PRE-PUNCHED

LOCATIONS TO FORM

THE CORNER MULLION.

THE CHANNEL SECTION

WILL FINISH 20mm

SHORT OF THE JAMB AT

EACH END.

168

SMALL EDGE

STEP 1.


STEP 3.

SCREW THE FRAME TOGETHER

AS SHOWN AT PRE-PUNCHED

LOCATIONS. ADDITIONAL HOLES

IN THE JAMB SECTIONS DO NOT

REQUIRE SCREWS.



SNAP i

181

STEP 4.



LEFT HAND SIDE (CONTINUED)

NOTCHED CORNERS TO

BOTTOM OF SHEET

154

LAY THESE SECTIONS OVER

THE PANEL AS SHOWN,

LOCKING THE SHEET INTO

THE BOTTOM CHANNEL.

SNAP i

MOVE THE TOP INFILL

CHANNEL (181) INTO

POSITION.

181

SNAP i

D

D

D

D

D

D

D



RIGHT HAND SIDE

172

154L



181

168

191

181

191

SMALL PAN

THIS SIDE

33A

SNAP

30A

SMALL EDGE

169

SNAP

STEP 1.

JOIN THE JAMB AND

CHANNEL SECTIONS

(191 & 172) TOGETHER AT

PRE-PUNCHED LOCATIONS

TO FORM THE CORNER

MULLION. THE CHANNEL

SECTION WILL FINISH 20mm

SHORT OF THE JAMB AT

EACH END.

STEP 1.

STEP 2.

JOIN THE TWO SHEETS TOGETHER

(30A & 33A) AT PRE-PUNCHED

LOCATIONS AND FIT THE TOP AND

BOTTOM CHANNELS (168 & 169).

ENSURE THAT THE PRE-PUNCHED

HOLES IN THE CHANNELS ARE

LOCATED AT THE LEFT HAND END

FOR CONNECTING THE REMAINING

JAMB AND CORNER MULLION.

THE TOP AND BOTTOM CHANNELS

WILL EXTEND PAST THE CORNER

MULLION BY 3mm.

STEP 3.

SCREW THE FRAME TOGETHER AS SHOWN AT PRE-PUNCHED LOCATIONS. ADDITIONAL HOLES IN

THE JAMB SECTIONS DO NOT REQUIRE SCREWS.



RIGHT HAND SIDE (CONTINUED)

STEP 4.

NOTCHED CORNERS TO

BOTTOM OF SHEET



SNAP

154L

181

NOTE: THIS EDGE

ONLY FOLDED AT 90

DEGREES.

LAY THESE SECTIONS OVER THE

PANEL AS SHOWN, LOCKING

THE SHEET INTO THE

BOTTOM CHANNEL.

SNAP

181

MOVE THE TOP

INFILL CHANNEL

(181) INTO POSITION.

D

D

D

D

D

D

D

D


FRONT PANEL ASSEMBLY

STEP 1.

PARTS REQUIRED:

2) CHANNELS (PART 160)

7) JAMBS (PART 191)

JOIN TWO JAMBS TOGETHER

AT PRE-PUNCHED LOCATIONS

AS SHOWN TO FORM TWO

DOUBLE JAMB SECTIONS.

160

191



191

191

160

191

191

STEP 2.

JOIN ALL SECTIONS TOGETHER, LINING UP

EACH JAMB WITH PRE-PUNCHED HOLES

LOCATED IN BOTH CHANNEL SECTIONS.

8mm




FRONT PANEL ASSEMBLY (CONTINUED)

SNAP i

STEP 3.

181

LOCK THE CHANNEL ON TO THE

SHEET AS SHOWN. THE CHANNEL

WILL FINISH 30mm IN FROM

EACH SIDE OF THE SHEET.

181

SNAP i

154

SNAP i

181

154

154R

THIS EDGE ONLY

FOLDED AT 90

DEGREES.

STEP 4.

LAY THESE SECTIONS, ONE AT A TIME,

OVER THE FRAME AS SHOWN, LOCKING

THE SHEETS INTO THE BOTTOM

CHANNEL.

D

D

D

D

D

D

192

STEP 6.

MOVE THE FIVE INFILL CHANNELS

INTO POSITION AND SCREW TO THE

TOP/BOTTOM CHANNELS WITH TWO

SCREWS EACH.

D

D

SNAP i

D

D

D

SNAP i

D

SNAP i

STEP 5.

MOVE THE DOOR HINGE

JAMB (PART 192) INTO

POSITION, LOCATING IT

"OVER THE TOP" OF THE

SHEET (154R) AND

SECURING IT TO THE

OTHER JAMB (191). (THE

SCREWS SECURING THE

EXISTING JAMB (191) WILL

HAVE TO BE REMOVED

AND THEN REPLACED)

181

D

D

D

181 D

D

181

D D

181

D

181


THIS EDGE ONLY



FRONT PANEL ASSEMBLY (CONTINUED)

STEP 7.

LAY THE DOOR PANEL IN THE

OPEN POSITION ON THE FRAME

AS SHOWN. USING THE SMALL

FLANGE POP RIVETS,

SECURE THE DOOR

TO THE DOOR

HINGE JAMB.

181

D

195

STEP 8.

FOR THE MIDRAIL ABOVE THE DOOR,

JOIN THE JAMB (195) TO THE

CHANNEL (181) AS SHOWN.

FIT THE MIDRAIL PARALLEL ABOVE THE

DOOR, TO THE SIDE JAMBS WITH

SCREWS FROM THE UNDERNEATH SIDE.


WALL PANEL ASSEMBLY



SIDE WALL PANEL CHANNELS FIT

INTO THE NOTCHED FRONT AND

REAR WALL PANEL CHANNELS

SCREW THE FRONT FRAME CORNER

JAMBS INTO THE PRE-PUNCHED

HOLES OF THE SIDE WALL CORNER

MULLIONS.


LAP THESE CORNER

SHEETS, DRILL AND

SCREW TOGETHER.




JOIN THE GABLES (16L + 16R) AND

MOVE INTO POSITION AS SHOWN.

DRILL AND SCREW THE GABLES

INTO THE TOP CHANNELS AS

SHOWN.

16R

16L

16L

16R

ATTACHING RIDGE

BEAM TO ROOF PANEL

97B

CHANNEL TYPE

78B THIS END

CHANNEL TYPE

81C THIS END




ROOF CONSTRUCTION

THE ROOF PANELS OVERHANG THE FRONT AND SIDE WALLS BY 37mm, BUT

DO NOT OVERHANG PAST THE REAR WALL.

INSIDE VIEW

SECURE THE RIDGE BEAM TO THE

GABLE SECTIONS WITH TWO SCREWS

AT EACH END. THE RIDGE BEAM

AND ROOF PANEL WILL PROTRUDE

37mm PAST THE FRONT GABLE,

AND WILL FINISH JUST OVER THE

OUTSIDE FACE OF THE REAR GABLES.

SECURE RIDGE BEAM TO

GABLE SECTIONS WITH

TWO SCREWS AT EACH

END. SECURE EACH ROOF

PANEL WITH ONE SCREW

IN EACH CORNER ONLY

AT THIS STAGE

THEN SECURE EACH ROOF PANEL

WITH ONE SCREW IN EACH CORNER

ONLY AT THIS STAGE AS SHOWN

BELOW.

INSIDE VIEW


13A

AFTER ATTACHING BOTH ROOF

PANELS TO WALLS AS SHOWN

ABOVE, FIT ONE REGENT BRACE

TO THE RIDGE BEAM AND FRONT

WALL AS SHOWN. YOU WILL HAVE

TO REMOVE AND REPLACE

EXISTING SCREWS AT FIXING

LOCATIONS. REPEAT THIS

PROCEDURE FOR THE REAR

WALL REGENT BRACE




FINAL CONSTRUCTION

AS THERE IS NO ROOF

OVERHANG OVER THE REAR

WALL, DRILL THROUGH THE

ROOF LIP FLASHING INTO

THE GABLE SECTIONS AND

SECURE WITH POP RIVETS.

THIS SHOULD BE DONE AFTER THE

REST OF THE ROOF HAS BEEN

SECURED TO THE OTHER WALLS.

VIEW OF

REAR WALL

BEND THE TOP AND BOTTOM

FLANGES AS SHOWN, THEN

HOOK THE BOTTOM FLANGES

UNDER THE ROOF LIP

FLASHINGS AND SCREW THE

TOP FLANGES AS SHOWN

FOR BOTH GABLE CAPS

14A

ANCHORING OF SHED

LOCATION OF 12

CONCRETE ANCHORS

BOLT & NUT

STEEL

ANGLE

WALL

SHEET

- EACH ANCHOR CONSISTS OF ONE NUT, BOLT,

DYNABOLT AND STEEL ANGLE

- DRILL A 10mm HOLE INTO THE WALL SHEET

- DRILL A 10mm HOLE INTO THE CONCRETE


SLAB

ASSEMBLY INSTRUCTION MANUAL AVIARY MODEL: A30231GK

DYNABOLT

06-02-2018 PAGE 25

FITTING OF WIRE MESH

ALL MESH SHEETS ARE FITTED TO THE

INSIDE OF THE AVIARY

WARNING

IT IS RECOMMENDED THAT NEW

GALVINESED MESH SHOULD BE

WEATHERED FOR TWO (2) MONTHS

OR SCRUBBED WITH A MILD ACIDIC

SOLUTION SUCH AS VINEGAR, THEN

RINSED WITH WATER BEFORE

BEING USED IN BIRD HOUSING

APPLIANCES.



INSIDE VIEW

OF AVIARY


THE MESH SHEETS ARE FIXED TO

FRAMEWORK USING THE LARGE FLANGE

RIVETS SUPPLIED.

WORKING FROM INSIDE THE AVIARY,

LOCATE THE FIRST MESH SHEET OVER

THE FRAMEWORK. DRILL 3mm HOLES

AND FASTEN WITH RIVETS TO THE

FRAMEWORK AT 150mm CENTRES.

IT IS IMPORTANT TO CONTINUALLY

STRETCH THE MESH TO ENSURE A

SMOOTH TIGHT FINISH.

replacement or refund for a major failure and for compensation for any other foreseeable loss or damage. You are also entitled

LOCATE RIVETS AT THE INSIDE

INTERSECTION OF THE WIRE TO

FACILITATE TIGHTENING OF THE MESH

AS SHOWN.

three business days to advise you of the assessment outcome of the claim, which may include your expenses incurred in making

ANY EXPOSED RAW ENDS OF WIRE

CAN BE FOLDED INTO THE HOLLOWS

OF THE FRAMEWORK USING A SMALL

PAIR OF PLIERS OR TRIMMED BACK

WITH TIN SNIPS.




AUSTRALIA PRODUCT WARRANTY AGAINST DEFECTS

Congratulations on your purchase of an ABSCO SHED

ABSCO SHEDS, including garden sheds, garden beds, aviaries, storage units, garages, awnings and carports are made using high quality Australian made steel.

We are pleased to advise we warrant that the steel coating will not rust, crack, flake peel or blister for 30 years from date of purchase, when installed within Australia.

This warranty does not apply to surface deterioration of panels caused by 'Swarf” (Tiny particles of steel debris left from cutting, grinding or drilling operations) that has not been removed after building construction, or as a result of contact with damp soil, chemicals, fertilisers or other corrosive substances.

This warranty covers any Absco product used for normal domestic use and installed in accordance with the installation instructions. The warranty does NOT cover Damage caused by storms, wind, rain snow or poor foundations.

This warranty does NOT cover ABSCO products installed in severe coastal, industrial or other highly corrosive environments. The warranty does not cover fasteners (screws, nuts, bolts, rivets, hasps or sliding padbolts).

The warranty is limited to replacement and delivery of components and does not include any labour or installation costs. The benefits given by the warranty are in addition to your other rights and remedies under a law in relation to the goods or services to which the warranty relates.

The warranty applies to the exclusion of all other representations, guarantees or warranties express or implied, our goods come with guarantees that cannot be excluded under the Australian consumer law and is not transferable. You are entitled to a replacement or refund for a major failure and for compensation for any other foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of an acceptable quality and the failure does not amount to a major failure. For further information go to http://www.consumerlaw.gov.au

.

Please retain a proof of purchase (sales docket or invoice) or register your warranty within 30 days of purchase here: www.absco.com.au/register_warranty.php

In the unlikely event a warranty claim is made, it must be supported by photographic evidence and details of the defect, including component part numbers, together with proof of purchase documentation (or on-line registration of purchase) and forwarded to the address below. Upon receipt of the warranty claim, the Customer Service Manager will contact you within three business days to advise you of the assessment outcome of the claim, which may include your expenses incurred in making the claim.

THE CUSTOMER SERVICE MANAGER, ABSCO INDUSTRIES, PO BOX 119 ACACIA RIDGE QLD AUSTRALIA 4110

PHONE: 1800 029701 FAX: 07-33441191 EMAIL: [email protected]

Issued 01 January 2013


This warranty does not apply to surface deterioration of panels caused by 'Swarf” (Tiny particles of steel debris left from cutting, replacement or refund for a major failure and for compensation for any other foreseeable loss or damage. You are also entitled



ABSCO SHEDS - STORAGE GUIDELINES

ABSCO SHEDS include garden sheds, garden beds, storage units, aviaries, garages, awnings and carports.

ABSCO SHEDS are designed to be weatherproof for normal weather conditions. In the event of extreme weather conditions such as heavy rain, combined with high wind gusts, the ridge capping, sheeting joins, screw fixings etc., may exhibit minor deformations which may allow some water entry. These areas should be checked regularly to ensure that maximum strength and protection is maintained.

Other weather conditions such as extreme heat and extreme cold, moist or dry air can influence the effects of concrete floor moisture and/or condensation on the underside of the roof sheets.

ABSCO SHEDS and storage units are primarily used for storage of garden equipment such as lawnmowers, wheelbarrows, garden tools etc. Storage items that might be adversely affected by any of the above conditions may require additional protection such as being sealed or covered by plastic sheets and/or stacked above the concrete floor on timber slats.

Waterproof sealants may be used to offer further protection where required around joins and screw fixings, as can rubber door seals and other products which are available from most hardware outlets.

Placement of waterproof sealants (silicone) between the base of the shed and concrete slab is not recommended, as this process can have a reverse effect, preventing excess water from escaping, resulting with water accumulating and being trapped inside the shed.

Absco accepts no responsibility for water entry, floor moisture, condensation or the condition of the Contents inside your Absco steel building arising from any of the pre-mentioned weather conditions.

three business days to advise you of the assessment outcome of the claim, which may include your expenses incurred in making


ABSCO SHEDS A30231GK Assembly & Instruction Manual

GENERAL INSTRUCTIONS

SITE PREPARATION

TOOLS REQUIRED TOOLS OPTIONAL

A NOTE ON SAFETY

30A

31A

45A

33A

13A

97BL

97BR

16L

16R

160L

160R

77BL

81BL

81CL

168L

77BR

81BR

81CR

168R

169L

78BL

181

172

191

169R

78BR

192

195

87B

14A

CSJ

QTY. = 1

QTY. = 8

QTY. = 2

QTY. = 1

AUSTRALIA PRODUCT WARRANTY AGAINST DEFECTS

ABSCO SHEDS - STORAGE GUIDELINES

Key Features

Related manuals

Overstock

2037800003

Glitzhome

2037800003

Glitzhome

1512202855

HOMCOM

838-040GY

CALHOME

SDH-WDN-SS-96

ABSCO SHEDS

J15231FK

ABSCO SHEDS

60303WK

Absco Industries

J52233WECOK

ABSCO SHEDS

Space Saver 23081SK

ABSCO SHEDS

30151SK

ABSCO SHEDS

ECO J23151GECOK

ABSCO SHEDS

J15301FK

Frequently Answers and Questions

What are the dimensions of the shed?

What materials are used in the construction of the shed?

Is the shed difficult to assemble?

Is the shed weather-resistant?